Setup Guide QT5-0264-V01 XXXXXXXX ©CANON INC.
ENGLISH Setup Guide
ENGLISH Canadian Radio Interference Regulations This digital apparatus does not exceed the Class B limits for radio noise emissions from a digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Industry Canada.
ENGLISH Table of Contents Preface.............................................................4 Introduction .....................................................4 Setup Outline ..................................................5 Confirming Your Connection Type ...............6 Connecting over Wireless LAN via an Access Point................................................................7 Connecting over Wired LAN ...........................8 Connecting with USB Connection...................
ENGLISH Preface Introduction Thank you for purchasing a Canon Multifunction Inkjet Printer. This Setup Guide uses the following symbols to indicate important information. Always observe the instructions indicated by these symbols. Warning Indicates a warning concerning operations that may lead to death or injury to persons if not performed correctly. In order to use the machine safely, always pay attention to these warnings.
ENGLISH Setup Outline Follow the steps below to start using the machine. Step 1 Confirming Your Connection Type. (see page 6) There are several ways to connect the machine and your computer. Decide on a connection type that matches your network setup. Step 2 Setting Up. (see page 11) Place the machine and install the print head and the ink tanks. Even though the machine is intended to be used over a wireless or wired LAN, it must be placed temporarily near the computer to do the setup via a USB cable.
ENGLISH Confirming Your Connection Type If your machine is connected to a network, it can be shared by multiple computers. This machine can be used over a wireless or wired LAN, as well as with USB connection. Connection types available for this machine are as follows.
ENGLISH Connecting over Wireless LAN via an Access Point Your computer communicates with the machine via an access point (the infrastructure mode). To share the machine among multiple computers, connect them to the access point. Important z When using this machine in a wireless LAN setup, use the infrastructure mode. It does not support the ad-hoc mode. z An access point is needed to set up the infrastructure mode.
ENGLISH Connecting over Wired LAN Your computer communicates with the machine via an Ethernet network. The Internet LAN cable Broadband modem with router Hub Important A hub and LAN cable are required to connect this machine to a wired LAN. These must be purchased separately. Note The type of device in use in your network may vary. Refer to the manual of your device or contact its manufacturer for details. Connecting with USB Connection Your computer communicates with the machine via a USB cable.
ENGLISH Combination of USB Connection and LAN (Wireless or Wired) Using both USB Cable and Wireless LAN Connections A computer communicates directly with the machine with a USB cable, while other computers are connected over a wireless LAN (infrastructure mode). You can exploit this configuration by setting up the machine over either a USB connection first, or over a wireless connection first.
ENGLISH Using both USB Cable and Wired LAN Connections A computer communicates directly with the machine with a USB cable, while other computers are connected over wired LAN. You can exploit this configuration by setting up the machine over either a USB connection first, or over a wired connection first. You can connect to a USB-connected machine from another computer over wired LAN, and connect another computer by USB to a wired LAN-connected machine.
ENGLISH Setting Up Note z Please confirm bundled thing by the illustration printed on the flapped lid of the packing box. z Even though the machine is intended to be used on a wireless or wired LAN, it must be placed temporarily near the computer to do the setup via a USB cable. Place the machine in the location where you will use it over a wireless or wired LAN as instructed during setup.
ENGLISH 3 Press [ON/OFF] on the Operation Panel to turn on the machine. 4 Use [ ] or [ ] on the Operation Panel to select the language for the LCD display, then press [OK]. The message will be displayed. Note z The language setting may not be available depending on the country of purchase. z You can change the language for the LCD display at anytime. For details, see “Language selection” in the User’s Guide.
ENGLISH 2 Pull out the Paper Output Tray extension. Important Press the Open Button to open the Paper Output Tray if it does not open automatically. 3 Open the Inner Cover (A). Important For customers in the United States Write down the serial number located inside the machine (B). You will need this later to register the product. (A) (B) 4 Raise the Print Head Lock Lever (A) completely. (A) Important Be careful not to touch any parts inside the machine, other than the Print Head Lock Lever.
ENGLISH 6 Remove the protective cap (A) from the Print Head. (A) Caution There might be some transparent or light blue ink on the inside of the bag the print head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. Note z Do not touch the print head nozzles or electrical contacts (B). z Do not attempt to reattach the protective cap once it has been removed. 7 Insert the Print Head.
ENGLISH Installing the Ink Tanks Caution z For safety reasons, store ink tanks out of the reach of small children. z Do not drop or shake ink tanks as this may cause the ink to leak out and stain your clothes and hands. z Be sure to remove the clear film from the ink tank in the exact order as shown in step 1. 1 To prepare the cyan ink tank first, pull the orange tape (A) off in the direction of the arrow, then remove the protective film (B) completely.
ENGLISH 4 Press the mark on the ink tank until it clicks into place and then its lamp lights red. 5 Use the same procedure to install the other ink tanks into their appropriate slots. Note z Ensure that all the ink tanks are installed in the order directed by the color guide (A). The machine cannot be used unless all the ink tanks are installed. z Ensure that all the ink tank lamps light red. 6 Close the Inner Cover. 7 Close the Scanning Unit (Printer Cover).
ENGLISH Aligning the Print Head from the Operation Panel This procedure is necessary to get the best print results. The Print Head positions are automatically aligned. When the pattern shown on step 3 is printed, the alignment is completed. Be sure to align the Print Head to ensure print quality. 1 Open the Paper Support (A), then pull out the extension. (A) Pinch and slide the paper guide (B) to the left end.
ENGLISH 3 Use [ [OK]. ] and [ ] to select , then press The Print Head alignment pattern will be printed in black and blue. Note z Print Head alignment will take several minutes to complete. Do not start another operation until the alignment is completed. z If this message does not appear after closing the Scanning Unit (Printer Cover), see “Aligning Print Head automatically” in the User’s Guide.
ENGLISH Confirming the Setup Environment 1 Ensure that the machine and the computer are turned off. Important Be sure [COPY] stops flashing and all the lamps on the Operation Panel are off. 2 Turn on the computer. Note z When using Windows XP or Windows 2000, you must log on as an administrator or have administrative privileges. Do not switch users during setup. z Close any open software applications including anti-virus, computer security and other software.
ENGLISH On Firewalls A firewall is a system that prevents unauthorized access to a local network from the outside. When setting up the machine for a use over a network, disable the firewall of your security software during the setup. Any firewall feature provided by security software may prevent proper setup or communication over a network.
ENGLISH Confirming Settings of your Access Point When setting up the machine to be used over wireless LAN, the machine’s network settings are configured to match those of the access point. Therefore, if you are using wireless LAN, we recommend that you confirm the necessary information on the access point before entering the setup process. Check and fill in the table below.
ENGLISH z If IP address filtering is enabled Disable the access point’s IP address filtering feature while setting up the machine. After setup is complete, configure the machine to communicate with other devices and then turn back the IP address filtering feature on. z If Client-to-Client Blocking is enabled Disable the Client-to-Client Blocking feature while using the machine. z Some access points are capable of automatically switching between wireless channels.
Installing the Software The following software programs are included on the Setup CD-ROM: MP Drivers On-screen Manual MP Navigator Easy-WebPrint Easy-PhotoPrint ArcSoft PhotoStudio ScanSoft OmniPage SE Canon IJ Network Tool * The contents of the Setup CD-ROM may differ depending on the country of purchase. Important If you have an earlier version of the MultiPASS Suite software installed on your computer, uninstall this version before installing the new version.
ENGLISH 2 Follow the instructions displayed on screen. When the screen shown on the right is displayed, click [Easy Install]. Note When you select [Easy Install], the items included in the CD-ROM are installed automatically. To select particular items to install, click [Custom Install] and follow the instruction on the screen. 3 When the list of applications to install appears, verify the contents, click [Install], then follow the instructions on the screen.
Which connection type do you intend to use ? Not being used (not set up) To use a wireless or wired LAN connection z “First-time Setup for Use over Wireless LAN” on page 25. ENGLISH How is the machine currently being used ? To use a USB connection z “Setting Up for Use with USB Connection” on page 34. z “First-time Setup for Use over Wired LAN” on page 31.
ENGLISH 2 When the screen shown on the right appears, connect the machine with a USB cable. Note To set up a machine that is not yet connected to a LAN, connect to it by USB. 3 Turn on the machine. If the machine is recognized, the next screen will appear automatically. Note If the connection is not recognized, click [Help] and follow instructions on how to solve the problem. 4 When the [Setup Preparations] dialog box is displayed, confirm that preparation is complete, then click [Next].
ENGLISH 5 Select [Wireless LAN] and click [Next]. Note z If the wired LAN settings are already configured, the [Note on Network Settings] dialog box is displayed. Generally, click [Wireless connection only] to enable only wireless LAN. z If the machine’s network settings have been set before, the [Printer Network Setup] dialog box is displayed. For details, see “The [Printer Network Setup] dialog box is displayed during setup” on page 66. 6 Setup automatically detects access points.
ENGLISH 7 Setup automatically detects the machine. The MP800R connected with the USB cable is detected automatically. z When the machine is detected automatically The machine is detected automatically if no operation is required for connecting to the machine. Setup proceeds to step 8. z If the [Set Printer IP Address] dialog box is displayed If the machine is not detected automatically, the [Set Printer IP Address] dialog box is displayed. Click [Connect] to connect to the machine.
ENGLISH 9 When the screen shown on the right appears, remove the USB cable, and click [Next]. The network connection between the machine and the computer is now successfully established. To confirm the Setup Results, click [View Setup Results]. To change the port name, click [Set Port Name] on the [Setup Results] dialog box. For details, see “Changing the port name” on page 69. Note If “Unsafe Removal of Device” is displayed, click [OK].
ENGLISH 13 When the screen shown on the right appears, click [Exit]. Note z If the screen shows a check box for restarting system, you can restart the system instead of the program. To restart the system, ensure that box is selected, and then click [Restart]. z To view the On-screen Manual, double-click the [MP800R On-screen Manual] shortcut icon on the desktop, or click [Start] and select [All Programs] (or [Programs]), [Canon MP800R Manual] and [MP800R On-screen Manual]. z Microsoft Internet Explorer® 5.
ENGLISH First-time Setup for Use over Wired LAN When you are setting up the machine to be used over wired LAN, follow these steps to set up the machine and your computer. 1 In the [Setup Method] screen, select [Set up the printer and the computer] and click [Next]. 2 When the screen shown on the right appears, connect the machine with a USB cable. Note To set up a machine that is not yet connected to a LAN, connect to it by USB. 3 Turn on the machine.
ENGLISH 4 When the [Setup Preparations] dialog box is displayed, confirm that preparation is complete, then click [Next]. Note If the machine’s network settings are already configured, the [Setup Environment Confirmation] dialog box appears asking you for confirmation to use the machine with the current settings. You can proceed with the setup using the current network settings. To do so, click [Use as is]. To reconfigure the network settings, click [Reconfigure]. 5 Select [Wired LAN].
ENGLISH 8 When the [Network Setup of the Card Slot] dialog box is displayed, specify the drive letter, then click [Next]. z If “Communication with the Card Slot failed.” is displayed Click [Retry]. If it still fails, see ““Communication with the Card Slot failed” is displayed during setup” on page 68. Note z If “Cannot map any more drives, because all the drive letters are assigned” is displayed, make an available drive letter manually, and try the network setup of the Card Slot again.
ENGLISH 10 When the screen shown on the right appears, click [Exit]. Note z If the screen shows a check box for restarting system, you can restart the system instead of the program. To restart the system, ensure that box is selected, and then click [Restart]. z To view the On-screen Manual, double-click the [MP800R On-screen Manual] shortcut icon on the desktop, or click [Start] and select [All Programs] (or [Programs]), [Canon MP800R Manual] and [MP800R On-screen Manual]. z Microsoft Internet Explorer 5.
When the screen shown on the right appears, connect the machine with a USB cable. 3 Turn on the machine. ENGLISH 2 If the machine is recognized, the next screen will appear automatically. Note If the connection is not recognized, click [Help] and follow its instructions. Note For customers in the United States When the online registration dialog box appears, follow the on-screen instructions to register your product.
ENGLISH 4 When the screen shown on the right appears, click [Exit]. Note z If the screen shows a check box for restarting system, you can restart the system instead of the program. To restart the system, ensure that box is selected, and then click [Restart]. z To view the On-screen Manual, double-click the [MP800R On-screen Manual] shortcut icon on the desktop, or click [Start] and select [All Programs] (or [Programs]), [Canon MP800R Manual] and [MP800R On-screen Manual]. z Microsoft Internet Explorer 5.
ENGLISH 3 Setup automatically detects the machine. The MP800R connected to the network is detected automatically. Note z If the machine was not detected, confirm the following and click [Update]. – Ensure that the machine is on. – Ensure that the firewall of any security software is turned off. For details on firewalls, see “On Firewalls” on page 20. – When using wireless LAN, confirm that the computer can communicate with the access point.
ENGLISH z If “Communication with the Card Slot failed.” is displayed Click [Retry]. If it still fails, see ““Communication with the Card Slot failed” is displayed during setup” on page 68. Note z If “Cannot map any more drives, because all the drive letters are assigned” is displayed, make an available drive letter manually, and try the network setup of the Card Slot again. z If “The Card Slot is already mapped as Network Drive to this computer” is displayed, the Card Slot is already setup. Click [Next].
Installing the Software The following software programs are included on the Setup CD-ROM: MP Drivers On-screen Manual MP Navigator Easy-PhotoPrint ArcSoft PhotoStudio ScanSoft OmniPage SE Canon IJ Network Tool * The contents of the Setup CD-ROM may differ depending on the country of purchase. Important Do not connect the machine to Mac OS 9 or Mac OS X Classic environments since they are not supported.
ENGLISH 5 When the list of applications to install appears, verify the contents, click [Install], and then follow the instructions on the screen. Move the cursor over items to display explanations of each application below. Note The list of applications may differ depending on the country of purchase. 6 Read the License Agreement and click [Yes]. Note For customers in the United States When the online registration dialog box appears, follow the on-screen instructions to register your product.
ENGLISH How is the machine Which connection type do you intend to use ? currently being used ? Used over a wireless or wired LAN To enable to use the machine from another computer over a LAN z “Setting Up an Additional Computer to Use a Machine Already Connected to a Network” on page 52. Used over a USB connection To also enable to use over a wireless or wired LAN z “First-time Setup for Use over Wireless LAN” on page 41.
ENGLISH 3 Turn on the machine. 4 5 Click [OK] on the [Setup Preparations] screen. Select [Setup] from the [Canon IJ Network Tool] pop-up menu and [MP800R] in [Printers], then click [OK]. If Canon IJ Network Tool does not start automatically, select [Library] - [Printers] - [Canon] [BJPrinter] - [Utilities] - [Canon IJ Network Tool]. Note z If no printer is detected, check that your machine is connected with a USB cable and turned on, then click [Update].
ENGLISH 7 Setup automatically detects access points. Important If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party. z When your access point is detected automatically The access point is detected automatically if no operation is required for connecting to the access point. Setup proceeds to step 8.
ENGLISH 9 When the screen shown on the right appears, remove the USB cable and click [Next]. The network connection between the machine and the computer is now successfully established. 10 Place the machine in the location where you will use it, then turn it on. 11 Click [Next] in the [Connection Performance Measurement] dialog box. Measuring of the communication performance starts, and the results are displayed. Note Measuring takes a few minutes. You can cancel measuring by clicking [Cancel].
ENGLISH 13 On the Printer Setup Utility (Printer Center on Mac OS X v.10.2), click [Add]. 14 Click [More Printers] on the [Printer Browser] dialog box. 15 Select [CANON IJ Network] from the pop-up menu, select [MP800R] from the list of printers, and click [Add]. The alphanumeric string after the machine name is its MAC address. 16 Confirm that your machine is added to the list of printers.
ENGLISH Note z When using the Card Slot over the network, mount the Card Slot referring to “Using the Card Slot over a Network” in the Network Guide. z To view the On-screen Manual, double-click the [MP800R On-screen Manual] alias on the desktop. First-time Setup for Use over Wired LAN When you are setting up the machine to be used over wired LAN, follow these steps to set up the machine and your computer. 1 Confirm that the screen shown on the right appears. 2 Connect the machine with a USB cable.
ENGLISH 5 Select [Setup] from the [Canon IJ Network Tool] pop-up menu and [MP800R] in [Printers], then click [OK]. If Canon IJ Network Tool does not start automatically, select [Library] - [Printers] - [Canon] [BJPrinter] - [Utilities] - [Canon IJ Network Tool]. Note z If no printer is detected, check that your machine is connected with a USB cable and turned on, then click [Update].
ENGLISH 8 Setup automatically detects the machine. The MP800R connected with the USB cable is detected automatically. If the machine was not detected, the [Printer IP Address Setup] dialog box appears. Ensure that the machine is on and connected to your computer with a USB cable, then click [Connect] to retry detection. If your machine is still not detected, refer to “The [Set Printer IP Address / Printer IP Address Setup] dialog box is displayed during setup” on page 64.
ENGLISH 13 Confirm that your machine is added to the list of printers. 14 On the Canon IJ Network Scanner Selector, select the MAC address of the machine from [Network Device List], then click [Apply] to use the machine as a scanner. Ensure that a check mark is displayed, then click [Exit] to close the dialog box. Note z To confirm the machine’s MAC address, print out the machine’s network setting information. For details, see “Printing Out Network Setting Information” on page 72.
ENGLISH 2 Connect the machine with a USB cable. 3 Turn on the machine. 4 5 Click [OK] on the [Setup Preparations] screen. Select [Setup] from the [Canon IJ Network Tool] pop-up menu, and click [Register Printer]. Note If Canon IJ Network Tool does not start automatically, select [Applications] from the [Go] menu, double-click the [Utilities] folder, double-click the [Printer Setup Utility] icon, and then proceed to step 7. When using Mac OS X v.10.2.
ENGLISH 7 Confirm that your machine is added to the list of printers. Note If the machine does not appear on the list, click [Add] and select [USB] from the pop-up menu. Select [MP800R] from the list of printers and click [Add]. After confirming that the machine is added to the list, exit [Printer Setup Utility] ([Print Center]). 8 On the Canon IJ Network Scanner Selector, click [Exit]. Note z Do not click [Apply].
ENGLISH Setting Up an Additional Computer to Use a Machine Already Connected to a Network This section describes how to enable a client to use a machine that is already connected to a wireless or wired LAN (setup from another computer is complete). This setup procedure only requires settings to be made on the client computer. Perform this setup procedure after installing the software.
ENGLISH 5 Click [Register Printer]. 6 When the screen shown on the right appears, click [Cancel]. The Printer Setup Utility (Printer Center on Mac OS X v.10.2) and Canon IJ Network Scanner Selector will start up. 7 On the Printer Setup Utility (Printer Center on Mac OS X v.10.2), click [Add]. 8 Click [More Printers] on the [Printer Browser] dialog box.
ENGLISH 9 Select [CANON IJ Network] from the pop-up menu, select [MP800R] from the list of printers, and click [Add]. Note z The alphanumeric string after the machine name is its MAC address. z If the machine was not detected, confirm the following. – Ensure that the machine is on. – Ensure that the firewall of any security software is turned off. – When using wireless LAN, confirm that the computer can communicate with the access point.
ENGLISH Troubleshooting Cause and measures on possible troubles in the setup procedure are explained here. Note If you do not find a description for your trouble here, refer to “Troubleshooting” on the User’s Guide and the Network Guide.
ENGLISH Checking information about the network z “Checking information about the network” on page 70 • “Checking the IP address or the MAC address of the machine” on page 70 • “Checking the IP address or the MAC address of the computer” on page 71 • “Checking the network setting information” on page 71 • “Confirming the version of Windows XP” on page 71 Cannot connect to the access point (the access point is not detected) Before you proceed to Troubleshooting, confirm the following: z The USB cable is sec
ENGLISH Problem The target access point is not detected Possible Cause and Measures If the machine or your computer cannot communicate with the target access point, follow the procedure below. 1 Ensure that the access point is on and then click [Update] in the [Access Points] dialog box. 2 If the access point is still not detected, move your machine closer to the access point and remove possible obstructions, then click [Update]. 3 Ensure that your computer can communicate with the access point.
ENGLISH Problem Using the machine in a multiple access point setup Possible Cause and Measures Confirm the following; z The access point to be used can communicate with the machine and the computer. z The wireless channel of the access point is far enough away with those of other access points. Windows XP may automatically connect to an unintended access point. Follow the steps below to make your access point the highest priority. 1 Select [Start] and [Connect To].
ENGLISH Problem How to set a WEP/ WPA key Possible Cause and Measures z When using WEP The key length, key format, the key to use (out of 1 to 4), and the authentication method must match among the access point, the machine, and the computer. For access points that use automatically generated WEP keys, use the hexadecimal key format for the machine. If you do not know the access point WEP key, refer to documentation provided with the access point or contact its manufacturer.
ENGLISH Cannot connect to the machine (the machine is not detected) Problem The machine is not detected Possible Cause and Measures z Confirm that the machine is turned on. z Move the machine closer to the access point or remove any obstacles. z Firewall features provided by security software may prevent proper setup or communication over a network. When setting up the machine for use over a network, disable any firewall provided by security software during the setup.
No printer is detected after the network settings are changed in Windows ENGLISH Problem Possible Cause and Measures Wait until the IP address is assigned to the computer. You may need to restart your computer. When you are using Windows Me or Windows 98, you need to restart the computer. Search for the machine again after confirming a valid IP address is assigned to the computer.
ENGLISH Problem The [Access Points] dialog box is displayed during setup (Continued) Possible Cause and Measures Encryption Method Do not use Select to disable encryption. Use WEP Transmission is encrypted using the WEP key you specified. Use WPA Transmission is encrypted using the passphrase (WPA key) you specified. The actual encryption key is renewed automatically at a certain time interval, making the transmission harder to break.
ENGLISH Problem The [Access Points] dialog box is displayed during setup (Continued) Possible Cause and Measures Encryption Method Do not use Select to disable encryption Use WEP Transmission is encrypted using the password (WEP key) you specified. Use WPA Transmission is encrypted using the passphrase (WPA key) you specified. The actual encryption key is renewed automatically at a certain time interval, making the transmission harder to break.
ENGLISH Problem Possible Cause and Measures The [Set Printer IP The following dialog box is displayed if no printer was detected on the Address / Printer IP network. Specify the IP address of the machine and click [Connect] to Address Setup] dialog retry the detection of the target printer. box is displayed during setup (1) (2) (3) (4) (1) Get IP address automatically Select to use an IP address provided by a DHCP server. This requires that the DHCP function is enabled on the router or access point.
ENGLISH Problem Possible Cause and Measures The [Set Printer IP Address / Printer IP Address Setup] dialog box is displayed during setup (Continued) (1) (2) (3) (1) TCP/IP Setting Select [Get IP address automatically] or [Use next IP address]. Select [Get IP address automatically] to search for the target printer automatically. If it fails, check the network settings and the network connection.
ENGLISH Problem The [Printer Network Setup] dialog box is displayed during setup Possible Cause and Measures The [Printer Network Setup] dialog box is displayed in the following cases. - when you are re-setting a machine whose setup was canceled halfway - when you changed the network settings - when you are already using a machine over a wireless or wired LAN If you canceled setup or changed the network settings, perform network setup again.
ENGLISH Problem “You have connected the printer to an unsecured wireless network” is displayed during setup Possible Cause and Measures Security is not configured on the access point. The machine can still be used, so continue the setup procedure to complete it. Important If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party.
ENGLISH Problem Possible Cause and Measures To disable the Windows Firewall: “Communication with the Card Slot failed” is displayed during setup (Continued) 1 Click [Start], [Control Panel], and [Windows Firewall]. 2 Select [Off] and click [OK]. To open port 137:139: 1 Click [Start], [Control Panel], and [Windows Firewall]. 2 Select the [Advanced] tab and select the target connection, and click [Settings]. 3 Select the [Services] tab, and click [Add].
ENGLISH Re-setting the machine Problem Re-setting the machine Possible Cause and Measures Restore the machine to the factory default and set up the machine again. For details, see “Printing and Initializing Network Settings” on page 72. For setup procedures, see “Confirming the Setup Environment” on page 19. The admin password set to the machine was forgotten Problem The admin password was forgotten Possible Cause and Measures Restore the machine setting to factory default.
ENGLISH Troubles in the network setup of the Card Slot Problem Unable to determine whether the Card Slot is mounted Possible Cause and Measures Open [My Computer], and find the [canon_memory on ‘MP800R(xxxxxxxxxxxx)’] icon with the mapped drive letter. * xxxxxxxxxxxx are 12 alphanumeric characters. * The icon name may differ depending on the language version of Windows you are using. The [CANON_MEMORY] icon appears on the desktop.
ENGLISH Problem Checking the IP address or the MAC address of the computer Possible Cause and Measures To check the IP address or MAC address assigned to the computer, follow the procedure below. z When using Windows XP/Windows 2000 1 From the [Start] menu, select [(All) Programs], [Accessories], and then [Command Prompt]. 2 Enter “ipconfig /all” and press the [Enter] key. The IP addresses and the MAC addresses of the network devices installed in your computer are displayed.
ENGLISH Printing and Initializing Network Settings Printing Out Network Setting Information 1 2 3 4 5 6 Press [ON/OFF] to turn on the machine. Press [Menu]. Use [ ] or [ ] to select , then press [OK]. Use [ ] or [ ] to select , then press [OK]. Use [ ] or [ ] to select , then press [OK]. Use [ ] or [ ] to select , then press [OK]. The information as follows is printed out.
Use [ ] or [ ] to select , then press [OK]. Use [ ] or [ ] to select , then press [OK]. Use [ ] or [ ] to select , then press [OK]. Use [ ] or [ ] to select , then press [OK]. ENGLISH 3 4 5 6 z Initializing with Canon IJ Network Tool 1 2 3 Connect the machine and your computer with a USB cable. Turn on the machine. Start Canon IJ Network Tool.
ENGLISH Conformity declaration for R&TTE Czech Canon tímto prohlašuje, že tento PIXMA MP800R je ve shodČ se základními požadavky a dalšími pĜíslušnými ustanoveními smČrnice 1999/5/ES. Danish Undertegnede Canon erklærer herved, at følgende udstyr PIXMA MP800R overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Canon declara que este PIXMA MP800R está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/ CE. Slovenian Canon izjavlja, da je ta PIXMA MP800R v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloþili direktive 1999/5/ES. Slovak Canon týmto vyhlasuje, že PIXMA MP800R spĎĖa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
Regulatory Information For 120V, 60Hz model Color Printer Model: K10266 (Contains IC: 498C-K30254) This device complies with Part 15 of the FCC Rules and RSS-210 of the IC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Setup Guide QT5-0264-V01 XXXXXXXX ©CANON INC.
