Photo All-In-One MP980 series Getting Started =Read Me First= Make sure to read this manual before using the machine. Please keep it in hand for future reference.
■ Sy m b o l s The following symbols are used to mark important instructions. Observe these instructions. Instructions that, if ignored, could result in personal injury or material damage. Instructions that must be observed for safe operation. Additional explanations. Descriptions for operations that take some time to complete. • Microsoft is a registered trademark of Microsoft Corporation. • Windows is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries.
Contents Unlock the Scanning Unit (Cover) Turn the Power On Install the Print Head Install the Ink Tanks Align the Print Head Confirming the Setup Flow Setup the Machine and the Computer Loading Paper After Installing the Machine
1 Unlock the Scanning Unit (Cover) First, check the in c l u d e d i t e m s The Print Head is placed inside of the Paper Output Tray (A). 1 (B) Open the Paper Output Tray with your hands, and take out the Print Head. Print Head (C) (A) power cord ink tank • Manuals • Setup CD-ROM (containing the drivers, applications and on-screen manuals) 1 Open the Document Cover (B). the Scanner Lock Switch (C) towards the 2 Move release mark to unlock the Scanning Unit (Cover). 3 Close the Document Cover (B).
2 Turn the Power On 3 2 1 (B) (1) (2) (D) (C) (A) Plug in the power cord on the left side at the back of the machine and connect the other end to the wall outlet. Open the Operation Panel (A), then press the ON button (B) to turn on the machine. Use the { or } button (D) on the Operation Panel to select the language for the LCD, then press the OK button. The standby screen is displayed. • Make sure that the Document Cover (C) is closed.
3 Install the Print Head 2 1 (D) (E) (B) (A) (C) Open the Paper Output Tray (A), then lift the Scanning Unit (Cover) (B) until it locks into place. Raise the Print Head Lock Lever (E). The Scanning Unit (Cover) (B) is fixed automatically. The Print Head Holder (C) comes out. (This is where you install the Print Head.) • For your safety, always grip as illustrated. • Do not handle the Print Head roughly such as applying them excessive pressure or dropping them.
3 4 5 (E) Remove the Print Head from the silver package. Remove and discard the orange protective cap. Tilt the Print Head and set it in place. Lower the Print Head Lock Lever (E) completely. • Do not knock the Print Head against the sides of the Holder. • There may be some transparent or light blue ink on the inside of the bag the Print Head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items.
4 Install the Ink Tanks 2 1 (A) (1) (2) Pull the orange tape (1) in the direction of the arrow to peel off the protective film and remove the film (2) completely. While pressing down with your left thumb, twist off the orange protective cap (A) located on the bottom of the ink tank. • Do not handle the ink tanks roughly such as applying them excessive pressure or dropping them. • If the Print Head Holder moves to the right, close and reopen the Scanning Unit (Cover).
3 Install the I n k Ta n k 4 5 (B) Press the PUSH mark on the ink tank until it clicks into place. Make sure the Ink lamp lights red. Install all the other ink tanks in the same way. Install all the ink tanks. Close the Scanning Unit (Cover) (B). • Wait until the screen above appears (about 6 minutes) and go to the next step. • The machine may make some operating noises when preparing to print. This is normal operation. • Be sure to install it in a well-lit environment.
5 Align the Print Head 2 1 (A) (C) (C) (B) Open the Paper Support (A) and pull it out. Align the Print Head for better print results. This takes about 7 minutes. Use a sheet of supplied speciality paper (MP-101) for alignment. • Make sure that the Output Tray Extension (B) is extended. Move the Paper Guides (C) to both edges.
4 3 (D) (E) Load a sheet of supplied speciality paper (MP-101) in the Rear Tray (D). Confirm the message on the LCD (E) and press the OK button. • Print Head Alignment takes about 7 minutes to complete. Wait until the pattern is printed, then go to the next step. • Be sure to use the supplied speciality paper (MP-101) for Automatic Print Head Alignment. • MP-101 cannot be fed from the Cassette. Load it in the Rear Tray. • MP-101 has the front and back sides. Load it with the whiter side facing up.
5 5 6 (E) (F) Make sure that a pattern similar to the one shown in the illustration is printed. Confirm the message on the LCD (E), then load plain paper into the Cassette (F) and press the OK button. The standby screen is displayed on the LCD. 10 • When an error message is displayed on the LCD, refer to "An Error Message Is Displayed on the LCD" in "Troubleshooting" in the on-screen manual: Advanced Guide. • For details, refer to "22 Loading Paper" on page 58.
6 Confirming the Setup Flow ■ Co n f i r m i n g Yo u r C o n n e c t i o n Type Before starting setup, decide on the most suitable connection method for the machine. This machine can be used over a wireless or wired LAN, as well as via USB connection. USB Wireless LAN Wired LAN USB cable LAN cable Router Access point • Before connecting the machine to the network, confirm that configuration of the computer and network devices (router, access point, etc.
6 ■ Pre p a r a t i o n f o r S e t u p To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk, and setting configured according to the connection method. In addition, configure the machine's LAN settings to connect to the network. Read the following carefully before starting setup. The screens below are based on Windows Vista operating system Ultimate Edition (hereafter referred to as "Windows Vista") and Mac OS X v.10.5.
■ Set u p F l o w Which connection method do you intend to use? Network Is this your first time connecting the machine to the network? 8 14 USB USB Wired LAN 7 7 Yes No 7 7 Wireless LAN WPS WCN To set up an additional computer 20 20 21 8 14 (P.15) (P.34) (P.14) (P.14) (P.14) (P.14) (P.50) (P.50) (P.53) (P.15) (P.34) 9 15 8 14 8 14 8 14 8 12 18 (P.18) 13 A (P.31) B (P.39) (P.15) (P.34) (P.15) (P.34) (P.15) (P.34) (P.15) (P.28) (P.46) 10 16 11 17 12 18 12 13 19 (P.19) (P.
7 1 Setup the Machine and the Computer Machine's LAN Setting (A) 3 2 4 5 C D E F Use the Easy-Scroll Wheel (A) or the [ or ] button to select Settings, then press the OK button. Select Device settings, then press the OK button. Select LAN settings, then press the OK button. Select Change wireless/wired, then press the OK button. Next, read "Install the Software" ! 14 Windows Macintosh Select either to the connection method, then press the OK button. 8 (P.15) 14 (P.
8 Setup the Machine and the Computer Windows Install the Software If the Found New Hardware or Found New Hardware Wizard screen appears: 1 2 (A) A C (B) Press the ON button (A) to TURN OFF THE MACHINE. the USB cable connected to 1 Remove your computer. E The setup program should run automatically. The screen may close. In this case, proceed from . 2 Click Cancel to quit the screen. 3 Proceed from . Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.
8 3 Windows Vista 4 Windows Vista 5 A C E G AutoPlay screen appears, click Run Msetup4.exe. User Account Control screen appears, click Continue. If the same screen reappears in subsequent steps, click Continue. Click Easy Install. The drivers, application software, and on-screen manuals are installed automatically. I J 16 • If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.
Windows 6 7 A Go to either of the following procedures according to your connection method! A USB Click Install. Move the cursor over items to display explanations. Read the License Agreement screen carefully and click Yes. Installation starts. C Wired LAN E Wireless LAN Additional J Computer G WPS I WCN 9 (P.18) 10 (P.19) 11 (P.23) 12 (P.28) 12 (P.28) 12 (P.28) C E G I • Follow any on-screen instructions to install the software.
9 Setup the Machine and the Computer Windows USB Connection 1 2 A USB On the Setup Method screen, select Use the printer via USB, then click Next. When the Printer Connection screen appears, connect the machine to the computer with a USB cable, then turn on the machine. • When the machine is recognized by the computer, a message appears on the screen. • If you cannot go to the next procedure after 10 minutes, click Help and confirm the message.
10 Setup the Machine and the Computer Windows First-time Setup for Use over Wired LAN 1 2 Prepare Cables USB Cable On the Setup Method screen, select Connect printer to the network for the first time, then click Next. LAN Cable C Confirm that USB Cable and LAN Cable are Ready. When a confirmation screen for the machine's LAN setting appears, click OK. • Set the machine's LAN setting to Wired LAN active beforehand. For details, refer to “7 Machine's LAN Setting” on page 14.
10 4 3 C USB When the Printer Connection screen appears, connect the machine to the computer with a USB cable, then turn on the machine. Set up the machine over a USB connection until the network connection is complete. • The machine is recognized by the computer, then message appears on the screen. • If you cannot go to the next procedure after 10 minutes, click Help and confirm the message. • The USB port is located on the right side at the back of the machine.
Windows 6 5 D e t e c t the Machine C Connect the machine to the network device with a LAN cable (A), then click Yes. (A) USB When the Set Printer IP Address screen appears, click Connect. If the machine is detected automatically, the Set Printer IP Address screen does not appear. Go to the following procedure. Windows Vista Go to Step . Windows XP/2000 Go to Step . • If no connection is established even after Connect is clicked, refer to "5.
10 7 Windows XP/2000 C Windows 8 USB When the Network Setup of the Card Slot dialog box appears, specify the drive letter, then click Next. • If the error message appears, refer to "5 The following screen is displayed during setup" in the printed manual: Network Setup Troubleshooting. When the Setup Completion dialog box appears, remove the USB cable, then click Finish. • To change the port name, click View Setup Results, then click Set Port Name.
11 Setup the Machine and the Computer First-time Setup for Use over Wireless LAN 1 Windows 2 USB On the Setup Method screen, select Connect printer to the network for the first time, then click Next. When a confirmation screen for the machine's LAN setting appears, click OK. When the Printer Connection screen appears, connect the machine to the computer with a USB cable, then turn on the machine. E Set up the machine over a USB connection until the network connection is complete.
11 3 E When the Setup Preparations dialog box appears, confirm that preparation is complete, then click Next. 4 Detect Access Point When the Access Points screen appears, select an access point to use, then click Connect. When an access point is detected automatically, the Access Points screen does not appear. Go to step . • To connect to the access point with WEP or WPA displayed in the Encryption column, enter the network key (WEP key or WPA key) in Network Key, then click Connect.
Windows 5 6 Detect the M a c h i n e When the Set Printer IP Address screen appears, click Connect. Windows XP/2000 When the Network Setup of the Card Slot dialog box appears, specify the drive letter, then click Next. E If the machine is detected automatically, the Set Printer IP Address screen does not appear. Go to the following procedure. Windows Vista Go to Step . Windows XP/2000 Go to Step . • If no connection is established even after Connect is clicked, refer to "5.
11 7 8 USB E When the Setup Completion dialog box appears, remove the USB cable, then click Next. • To change the port name, click View Setup Results, then click Set Port Name. For details, refer to "8 Changing the port name" in the printed manual: Network Setup Troubleshooting. • If Unsafe Removal of Device is displayed, click OK. 26 Turn off the machine, then place the machine in the location where you will use it, and turn on it.
Windows 9 10 On the Connection Performance Measurement screen, click Next. Confirm the measurement results, then click Finish. Measuring of the communication status starts, and the results are displayed. Ensure that is displayed in Connection performance between the printer and the access point. E • If any symbol other than is displayed, refer to displayed comments and Help for improving the status of communication link. • Measuring takes a few minutes. You can cancel measuring by clicking Cancel.
12 Setup the Machine and the Computer Connect the Wired LAN / Wireless LAN 2 1 (A) Press the ON button (A) to TURN ON THE MACHINE. G I J 28 • Make sure that the computer you are setting up is not connected to the machine with a USB cable. • For wired LAN connections, confirm that the machine is connected to the network with a LAN cable. On the Setup Method screen, select Printer is already connected to the network, then click Next.
Windows 3 When the Printers screen appears, make sure that the machine is selected and click Next. Windows Vista Go to Step . Windows XP/2000 Go to Step . • When the machine is not detected, make sure of the following, click Update. – The machine is turned on. – When using wireless LAN : The computer is connected to the access point. – When using wired LAN : The machine is connected to the network device with the LAN cable.
12 4 Windows XP/2000 When the Network Setup of the Card Slot dialog box appears, specify the drive letter, then click Next. Windows 5 When the Setup Completion screen appears, click Finish. G I J • If the error message appears, refer to "5 The following screen is displayed during setup" in the printed manual: Network Setup Troubleshooting. • To change the port name, click View Setup Results, then click Set Port Name.
13 Setup the Machine and the Computer Windows Information 2 1 A C (A) When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next. Click Next. E It may take a while for the next screen to appear. Click Next only once. G I • For details, refer to "22 Loading Paper" on page 58.
13 4 3 A Serial Number Serial * * * *Number *** ******* C E G I J 32 Click Next. If connected to the Internet, the user registration page appears. Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine. • Internet connection is required. (Connection fees apply.) • To register later, click Cancel. User Registration can be started from the Solution Menu icon. For details, refer to "Solution Menu" on page 62.
Windows 5 A C Click Exit. If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. After restarting the computer, remove the Setup CD-ROM and keep it in a safe place.
14 Setup the Machine and the Computer Install the Software 2 1 3 B D F USB Connect one end of the USB cable to the computer and the other to the machine. Make sure the machine is turned on. H • The USB port is located on the right side at the back of the machine. • When using WPS (Wi-Fi Protected Setup) or connecting an additional computer, make sure that the machine is turned on, then go to step . It is not necessary to connect the machine to the computer with a USB cable.
Macintosh 4 5 B D Enter your administrator name and password. Click OK. Click Easy Install. If you do not know your administrator name or password, click Help, then follow the on-screen instructions. The drivers, application software, and on-screen manuals are installed automatically. F H • If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.
14 6 7 8 B D (A) Click Install. F Move the cursor over items to display explanations. Read the License Agreement screen carefully and click Yes. When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next. Installation starts. H • Follow any on-screen instructions to install the software. K 36 • For details, refer to "22 Loading Paper" on page 58.
Macintosh 9 10 Serial Number Serial * * * *Number *** ******* B D Click Next. Click Next. If connected to the Internet, the user registration page appears. Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine. F H • Internet connection is required. (Connection fees apply.) • To register later, click Cancel. User Registration can be started from the Solution Menu icon.
14 Macintosh 11 B Go to either of the following procedures according to your connection method! D F Click Restart. B USB When the computer restarts, Canon IJ Network Tool starts automatically. D Wired LAN Click Restart to restart the computer. After restarting the computer, remove the Setup CD-ROM and keep it in a safe place. F Wireless LAN H H WPS • When using Mac OS X v.10.3.
15 Setup the Machine and the Computer USB Connection Macintosh 1 B On the Canon IJ Network Tool screen, select USB connection, then click OK.
16 Setup the Machine and the Computer First-time Setup for Use over Wired LAN 1 2 3 D On the Canon IJ Network Tool screen, select LAN connection, then click OK. • Set the machine's LAN setting to Wired LAN active beforehand. For details, refer to “7 Machine's LAN Setting” on page 14. 40 If the Setup Preparations dialog box appears, confirm that preparation is complete, then click OK. Select Setup in the pop-up menu, select MP980 series in Printers, then click OK.
Macintosh 4 (A) USB 5 USB D Connect the machine to the network device with a LAN cable (A), then click Yes. When the Setup Completion dialog box appears, remove the USB cable, then click OK. The Printer Setup Utility and Canon IJ Network Scanner Selector will start up. • If the Set Printer IP Address dialog box appear, refer to "5.6 The Set Printer IP Address dialog box is displayed during setup" in the printed manual: Network Setup Troubleshooting.
17 Setup the Machine and the Computer First-time Setup for Use over Wireless LAN 1 F On the Canon IJ Network Tool screen, select LAN connection, then click OK. • Set the machine's LAN setting to Wireless LAN active beforehand. For details, refer to “7 Machine's LAN Setting” on page 14. 42 2 If the Setup Preparations dialog box appears, confirm that preparation is complete, then click OK. 3 Select Setup in the pop-up menu, select MP980 series in Printers, then click OK.
Macintosh 4 Detect Acce s s P o i n t When the Access Points screen appears, select an access point to use, then click Connect. When an access point is detected automatically, the Access Points screen does not appear. Go to step . F • To connect to the access point with WEP or WPA displayed in the Encryption column, enter the network key (WEP key or WPA key) in Network Password, then click Connect. For details on network keys, refer to "3.
17 5 Detect the M a c h i n e 6 7 (A) USB F When the Set Printer IP Address screen appears, confirm the contents, then click Connect. If the machine is detected automatically, the Set Printer IP Address screen does not appear. Go to step . • If no connection is established even after Connect is clicked, refer to "5.6 The Set Printer IP Address dialog box is displayed during setup" in the printed manual: Network Setup Troubleshooting.
Macintosh 8 On the Connection Performance Measurement dialog box, click Next. Measuring of the communication status starts, and the results are displayed. 9 Confirm the measurement results, then click Finish. Ensure that is displayed in Connection performance between the printer and the access point. The Printer Setup Utility and Canon IJ Network Scanner Selector will start up. • Measuring takes a few minutes. Measuring can be cancelled by clicking Cancel.
18 Setup the Machine and the Computer Macintosh Connect the Wired LAN / Wireless LAN 1 On the Canon IJ Network Tool screen, select LAN connection, then click OK. 2 If the Setup Preparations dialog box appears, confirm that preparation is complete, then click OK. 4 3 Select Setup in the pop-up menu, then click Register Printer. H When the Cancel Setup screen appears, then click Cancel. The Printer Setup Utility and Canon IJ Network Scanner Selector will start up.
19 1 Setup the Machine and the Computer Macintosh Add the Machine 2 Mac OS X v.10.4.x/v.10.3.9 Mac OS X v.10.5.x/v.10.4.x D When the Printer List screen appears, click Add. Wait for a while, then select Canon MP980 series and click Add. Mac OS X v.10.4.x Go to Step . Mac OS X v.10.3.9 Go to Step . In Mac OS X v.10.4.x, click More Printers in the Printer Browser screen. Mac OS X v.10.5.x Go to Step . Mac OS X v.10.4.x Go to Step .
19 3 Mac OS X v.10.4.x/v.10.3.9 4 Mac OS X v.10.4.x/v.10.3.9 D F H Select Canon IJ Network in the pop-up menu, select your machine’s name in the list of printers, then click Add. • The alphanumeric string after Canon MP980 series is the machine's MAC address. • If the machine has not been detected, make sure of the following. – The machine is turned on. – The firewall function of any security software is turned off.
Macintosh 5 6 D On the Canon IJ Network Scanner Selector screen, select Canon MP980 series Network in TWAIN Data Source Name and the MAC address of the machine in Network Device List, then click Apply to use the machine as a scanner. Confirm that a check mark is displayed, then click Exit to close the dialog box. Next, read "22 Loading Paper" on page 58! F H • To confirm the machine's MAC address, refer to "Troubleshooting" in the on-screen manual: Advanced Guide available via Solution Menu.
20 Setup the Machine and the Computer WPS Connection If your access point supports WPS (Wi-Fi Protected Setup), you can set the wireless LAN security easily. 1 (A) Use the Easy-Scroll Wheel (A) or the [ or ] button to select Settings, then press the OK button. G H 50 2 Select Device settings, then press the OK button. 3 Select LAN settings, then press the OK button.
Windows ／ Macintosh 4 Select Change wireless/ wired, then press the OK button. 5 Select Wireless LAN active, then press the OK button. 6 Select Wireless LAN settings, then press the OK button. 7 Select WPS settings, then press the OK button.
20 8 Select Push button method, then press the OK button. Windows ／ Macintosh 9 Press the OK button. 10 When the access point is ready, press the OK button on the machine, then press the WPS button on the access point within two minutes. The completion screen appears on the LCD of the machine, then the LAN settings screen returns. G H • To use the PIN code method for setup, select PIN method on step , then press the OK button.
21 Setup the Machine and the Computer Windows WCN Connection You can set the wireless LAN security on the machine easily by using the WCN (Windows Connect Now) function of Windows Vista together with a USB flash drive. • Canon assumes no responsibility for any damage or loss of stored data regardless of the cause. • If your USB flash drive cannot be attached to the direct print port of the machine, an extension cord for USB flash drives may be required. Purchase one at an electronics shop.
21 3 Click I want to add a wireless device or computer that is not on the list, using a USB flash drive. 4 Click Add the device or computer using a USB flash drive. 5 From the list, select the network name (SSID), then click Next. I • If the User Account Control screen appears, click Continue. If the same screen reappears in subsequent steps, click Continue.
Windows 6 Connect the USB flash drive to the computer, confirm that the drive name is displayed, then click Next. 7 When the above screen appears, remove the USB flash drive from the computer, then click Close.
21 8 (A) Use the Easy-Scroll Wheel (A) or the [ or ] button to select Settings, then press the OK button. I 56 9 Select Device settings, then press the OK button. 10 11 Select LAN settings, then press the OK button. Select Change wireless/ wired, then press the OK button.
Windows 12 13 14 15 Select Wireless LAN active, then press the OK button. Select Wireless LAN settings, then press the OK button. Select WCN settings, then press the OK button. Connect the USB flash drive to the direct print port (USB connector) on the front of the machine, then press the OK button. The completion screen appears on the LCD of the machine, then the LAN settings screen returns. Remove the USB flash drive from the machine.
22 Loading Paper This section explains how to load paper in the Cassette (A) and the Rear Tray (B). 1 Load in the Cassette 3 2 (F) (D) (B) (A) (A) (E) (C) Pull out the Cassette (A). Move the Paper Guides (E) and (F) to both edges. Load paper. The Cassette (A) supports plain paper (C) only. To print Photo Paper / Hagaki (D), be sure to load it in the Rear Tray (B). • Load paper with the printing side facing down.
4 6 5 (F) (A) (G) (E) Slide the Paper Guide (E) to align with the mark of paper size. Slide the Paper Guide (F) against left edge of the paper. The Paper Guide (E) will stop when it aligns with the corresponding mark of paper size. Do not exceed the Load Limit Mark (G). • There may be a little space between the Paper Guide (E) and the paper stack. Insert the Cassette (A) into the machine until it clicks into place. • To print on speciality paper, be sure to load it in the Rear Tray.
22 7 Load paper in the Rear Tray 8 9 10 (H) (J) (I) (I) (I) Open the Paper Support (H) and pull it out. Move the Paper Guides (I) to both edges. Load paper in the center of the Rear Tray. (I) Slide the left and right Paper Guides (I) against both edges of the paper. Do not exceed the Load Limit Mark (J). • Load paper in portrait orientation with the printing side facing up. • For details on media sizes and types you can use, refer to "Loading Paper" in the on-screen manual: Basic Guide.
After Installing the Machine ■ Ma n u a l s Safety Precautions Safety and Environment I n f o r m a t i on For proper use, read safety precautions before using the product. Getting Started (t his manual) Basic Guide (on-screen manua l ) Advanced Guide (on-screen manual) Network Setup Troubleshooting Describes how to set up and use your machine. Introduces the machine and its functions, the included manuals and application software.
■ Sol u t i o n M e n u Solution Menu is a gateway to functions and information that allow you to make full use of the machine! Example: Windows Vista Open various applications and on-screen manuals with a single click. You can start Solution Menu from the Solution Menu icon on the desktop (Windows) or on the Dock (Macintosh). If you have a problem with machine settings, click the Change settings or find solutions to problems icon in Solution Menu to open My Printer (Windows only).
■ Usi n g Yo u r M a c h i n e This machine allows you to print in various ways using the MP driver and application software installed on the computer. For example, you can print borderless photos, and create your own calendar etc. easily. Also, you can scan documents into a computer, and correct/enhance scanned images. For detailed operating procedures and functions, refer to the on-screen manuals.
Print Photos from a Memory Card Print images saved on a memory card used with digital cameras, etc. For more information on printing from a memory card, refer to "Printing from a Memory Card" in the on-screen manual: Basic Guide. *Supported Memory Cards (Adapter required for .) CF Memory Stick Duo Memory Stick PRO Duo 1 (C) (B) Memory Stick Micro MS SD Duo MS Memory Stick Memory Stick PRO SD Card SDHC Card MultiMediaCard (Ver.4.1) MultiMediaCard Plus (Ver.4.
2 (D) Load a sheet of 4" x 6" size photo paper in the Rear Tray (D) in portrait orientation. 3 (E) Rotate the Easy-Scroll Wheel (E) to display a photo to print. Alternatively, use the [ or ] button to select a photo. • For details, refer to "22 Loading Paper" on page 58.
4 5 6 (A) (B) (F) Press the [+] or [-] button to specify the number of copies, then press the OK button. The Print Settings Confirmation Screen appears. Press the Color button (F). Printing will start. After printing, open the Card Slot Cover (A), pinch the memory card and pull it straight out, then close the Card Slot Cover (A). • Do not remove the memory card while the Access lamp (B) is flashing. Saved data may be damaged.
Try Copying You can copy a document by simply placing it on the Platen Glass and pressing the Black button or the Color button. This section explains with Plain Paper. For various copying procedures, refer to "Copying" in the on-screen manual: Basic Guide. 1 2 3 (B) 4 (A) (D) (A) (C) (E) (F) Load A4 or Letter-sized plain paper in the Cassette. Open the Document Cover (A). Place the document face-down and align it with the Alignment Mark (B).
Print Photos from a Computer Easy-PhotoPrint EX allows you to print photos easily. This section explains how to print borderless photos using 4" x 6" size Photo Paper Plus Glossy II. The screens are based on Windows Vista. 1 2 4 3 (A) In Solution Menu, click OneClick to Photo Print. Easy-PhotoPrint EX starts. Select the image you want to print in a folder, then click Layout/Print. When a photo is selected, the number of copies is set to "1.
Getting Help from Canon Email Tech Support — www.canontechsupport.com Toll-Free Live Tech Support— (1-800-828-4040) This option provides live telephone technical support, free of service charges, Monday-Friday (excluding holidays), during the warranty period. Telephone Device for the Deaf (TDD) support is available at (1-866-251-3752). Ordering Information The following ink tanks are compatible with this product.
