MX390 series Online handleiding Scannen Nederlands (Dutch)
Scannen Scannen vanaf een computer Scannen met IJ Scan Utility Scannen met een toepassing die u gebruikt (ScanGear) Handige informatie over scannen Items plaatsen (wanneer u scant vanaf een computer) Scannen via het bedieningspaneel van het apparaat Gescande gegevens naar de computer sturen met het bedieningspaneel van het apparaat Basis Items instellen met het bedieningspaneel van het apparaat Opgeven hoe gereageerd moet worden op opdrachten van het bedieningspaneel met gebruik van IJ Scan Utility
Scannen vanaf een computer Scannen met IJ Scan Utility Scannen met een toepassing die u gebruikt (ScanGear) Handige informatie over scannen Items plaatsen (wanneer u scant vanaf een computer)
Scannen via het bedieningspaneel van het apparaat Gescande gegevens naar de computer sturen met het bedieningspaneel van het apparaat Basis Items instellen met het bedieningspaneel van het apparaat Opgeven hoe gereageerd moet worden op opdrachten van het bedieningspaneel met gebruik van IJ Scan Utility
Scannen met IJ Scan Utility Wat is IJ Scan Utility (scannersoftware)? IJ Scan Utility starten Eenvoudig scannen met Automatische scan Basis Foto's scannen Documenten scannen Scannen met voorkeursinstellingen Items scannen die groter zijn dan de glasplaat (Afbeelding samenvoegen) Meerdere items tegelijk scannen Meerdere documenten tegelijk scannen vanuit de ADF (automatische documentinvoer) Opslaan na controle van de scanresultaten Gescande afbeeldingen via e-mail verzenden Tekst extraheren van gescande af
Wat is IJ Scan Utility (scannersoftware)? IJ Scan Utility is een toepassing waarmee u op eenvoudige wijze foto's, documenten, enzovoort kunt scannen. U kunt in één handeling scannen en opslaan door op het bijbehorende pictogram in het hoofdscherm van IJ Scan Utility te klikken.
Belangrijk Sommige functies zijn alleen beschikbaar wanneer My Image Garden is geïnstalleerd. Opmerking Zie het 'Dialoogvenster Instellingen' voor informatie over het instellen van de toepassingen voor integratie.
IJ Scan Utility starten Selecteer Programma's (Applications) in het menu Ga (Go) van de Finder, en dubbelklik achtereenvolgens op de map Canon Utilities, de map IJ Scan Utility en het pictogram Canon IJ Scan Utility om IJ Scan Utility te starten.
Eenvoudig scannen met Automatische scan U kunt eenvoudig scannen door automatisch het itemtype te detecteren. Belangrijk De volgende typen items worden mogelijk niet goed gescand. In dat geval past u de bijsnijdkaders (scangebieden) aan in de volledige afbeeldingsweergave van ScanGear (scannerstuurprogramma) en voert u de scan opnieuw uit.
Foto's scannen U kunt via dit scherm foto's die op de plaat zijn geplaatst scannen met instellingen die geschikt zijn voor foto's. 1. Plaats de foto op de plaat. Items plaatsen (wanneer u scant vanaf een computer) 2. Start IJ Scan Utility. IJ Scan Utility starten 3. Klik op Instellingen (Settings...), selecteer het dialoogvenster Instellingen (Foto scannen) (Settings (Photo Scan)) en stel dan het papierformaat, de resolutie, enzovoort naar wens in.
Documenten scannen U kunt via dit scherm items die op de plaat zijn geplaatst scannen met instellingen die geschikt zijn voor documenten. 1. Plaats het item op de glasplaat. Items plaatsen (wanneer u scant vanaf een computer) 2. Start IJ Scan Utility. IJ Scan Utility starten 3. Klik op Instellingen (Settings...), selecteer het dialoogvenster Instellingen (Document scannen) (Settings (Document Scan)) en stel dan het papierformaat, de resolutie, enzovoort naar wens in.
Scannen met voorkeursinstellingen U kunt via dit scherm items die op de plaat zijn geplaatst scannen met uw voorkeursinstellingen die u eerder hebt opgeslagen. Dit is een gemakkelijke manier om veelgebruikte instellingen op te slaan of scaninstellingen in detail op te geven. 1. Start IJ Scan Utility. IJ Scan Utility starten 2. Klik op Instellingen (Settings...
Items scannen die groter zijn dan de glasplaat (Afbeelding samenvoegen) U kunt de linker- en rechterhelft van een item dat groter is dan de plaat scannen en deze tot één afbeelding samenvoegen. Items scannen die maximaal ongeveer twee keer zo groot zijn dan de glasplaat worden ondersteund. Opmerking Hierna wordt uitgelegd hoe moet worden gescand vanaf het item dat aan de linkerkant moet worden geplaatst. 1. Start IJ Scan Utility. IJ Scan Utility starten 2. Klik op Instellingen (Settings...
5. Zorg dat Links beginnen met scannen (Scan from Left) is geselecteerd in Richting selecteren (Scan Direction). 6. Plaats het item dat aan de linkerkant van het scherm moet worden weergegeven met de bedrukte zijde naar beneden op de glasplaat. 7. Klik op Start het scannen van afbeelding 1 (Start Scanning Image 1).
Het eerste item wordt gescand en verschijnt in 1. Opmerking Klik op Annuleren (Cancel) om het scannen te annuleren. 8. Plaats het item dat aan de rechterkant van het scherm moet worden weergegeven met de bedrukte zijde naar beneden op de glasplaat. 9. Klik op Start het scannen van afbeelding 2 (Start Scanning Image 2). Het tweede item wordt gescand en verschijnt in 2. Opmerking Klik op Annuleren (Cancel) om het scannen te annuleren.
10. Pas de gescande afbeeldingen desgewenst aan. Gebruik de taakbalk om te draaien of in/uit te zoomen, of sleep de afbeeldingen om hun posities aan te passen. Opmerking Selecteer het selectievakje Bijsnijdkaders aanpassen (Adjust cropping frames) om het gebied dat moet worden opgeslagen op te geven. Bijsnijdkaders aanpassen (IJ Scan Utility) Om een item opnieuw te scannen selecteert u de afbeelding in het voorbeeldgebied of de miniatuur bovenaan het scherm en klikt u op (Verwijderen).
De gecombineerde afbeelding wordt opgeslagen. Opmerking Raadpleeg 'Venster Afbeelding samenvoegen' voor details over het venster Afbeelding samenvoegen (Image Stitch). U kunt geavanceerde scaninstellingen opgeven in het dialoogvenster Instellingen (Scannen en samenvoegen) (Settings (Scan and Stitch)) door te klikken op Instellingen (Settings...).
Meerdere items tegelijk scannen U kunt twee of meer foto's (kleine items) die op de glasplaat zijn geplaatst tegelijk scannen en elke afbeelding apart opslaan. Belangrijk De volgende typen items worden mogelijk niet goed bijgesneden. In dat geval past u de bijsnijdkaders (scangebieden) aan in de volledige afbeeldingsweergave van ScanGear (scannerstuurprogramma) en voert u de scan opnieuw uit.
5. Kies bij Bron selecteren (Select Source) het type items dat u wilt scannen. 6. Selecteer Automatisch scannen (Auto scan) bij Papierformaat (Paper Size) en klik vervolgens op OK.
Het hoofdvenster IJ Scan Utility verschijnt. Opmerking Zie de volgende pagina's voor meer informatie over instellingsitems in het dialoogvenster Instellingen. Dialoogvenster Instellingen (Foto scannen) Dialoogvenster Instellingen (Document scannen) Dialoogvenster Instellingen (Aangepast scannen) 7. Klik op Aangepast (Custom). Er worden meerdere items tegelijk gescand. Opmerking Klik op Annuleren (Cancel) om het scannen te annuleren.
Meerdere documenten tegelijk scannen vanuit de ADF (automatische documentinvoer) Plaats meerdere documenten in de ADF (automatische documentinvoer) en scan deze tegelijkertijd. Opmerking U kunt meerdere documenten tegelijkertijd scannen vanuit de ADF wanneer u scant via Auto, Document, Aangepast (Custom) of ScanGear.
5. Selecteer bij Bron selecteren (Select Source) het type documenten dat u wilt scannen. Als u alleen de voorzijde van elk document wilt scannen, selecteert u Document (ADF/glasplaat) (Document (ADF/Platen)) of Document (ADF enkelzijdig) (Document (ADF Simplex)). Als u zowel de voorzijde als de achterzijde van elk document wilt scannen, selecteert u Document (ADF handmatig dubbelzijdig) (Document (ADF Manual Duplex)). 6. Stel de kleurenmodus, het documentformaat en de scanresolutie naar wens in.
documenten moet plaatsen voor het scannen van de achterzijde, is afhankelijk van de Inbindzijde (Binding Side). Als u klaar bent met het opgeven van de instellingen, klikt u op OK. Het hoofdvenster IJ Scan Utility verschijnt. Opmerking Zie de volgende pagina's voor meer informatie over instellingsitems in het dialoogvenster Instellingen. Dialoogvenster Instellingen (Document scannen) Dialoogvenster Instellingen (Aangepast scannen) 7. Klik op Document. Het scannen begint.
Als u onder Instellingen scanstand document... (Document Scan Orientation Settings...) Lange zijde (Long edge) selecteert bij Inbindzijde (Binding Side) Plaats de uitvoerdocumenten 180 graden gedraaid. Als u onder Instellingen scanstand document... (Document Scan Orientation Settings...) Korte zijde (Short edge) selecteert bij Inbindzijde (Binding Side) Plaats de documenten zonder de afdrukstand van de uitvoerdocumenten te wijzigen. 9. Klik op OK. Het scannen begint.
Opslaan na controle van de scanresultaten U kunt de scanresultaten controleren en de afbeeldingen vervolgens op een computer opslaan. Belangrijk U kunt de scanresultaten niet vóór het opslaan controleren wanneer u hebt gescand via Auto of het bedieningspaneel. Opmerking De vensters voor het scannen van foto's worden in de volgende beschrijvingen als voorbeeld gebruikt. 1. Start IJ Scan Utility. IJ Scan Utility starten 2. Klik op Instellingen (Settings...).
4. Schakel het selectievakje Scanresultaten controleren (Check scan results) in en klik op OK. Het hoofdvenster IJ Scan Utility verschijnt. Opmerking Zie de volgende pagina's voor meer informatie over instellingsitems in het dialoogvenster Instellingen. Dialoogvenster Instellingen (Foto scannen) Dialoogvenster Instellingen (Document scannen) Dialoogvenster Instellingen (Aangepast scannen) Dialoogvenster Instellingen (Scannen en samenvoegen) Dialoogvenster Instellingen (ScanGear) 5. Klik op Foto (Photo).
Opmerking De standaardmap voor het opslaan van bestanden is de map Documenten (Documents). 7. Klik op OK. De gescande afbeeldingen worden volgens de instellingen opgeslagen.
Gescande afbeeldingen via e-mail verzenden U kunt gescande afbeeldingen via e-mail verzenden. Opmerking De vensters voor het scannen van foto's worden in de volgende beschrijvingen als voorbeeld gebruikt. 1. Start IJ Scan Utility. IJ Scan Utility starten 2. Klik op Instellingen (Settings...). Het dialoogvenster Instellingen wordt weergegeven. Dialoogvenster Instellingen 3. Klik op Foto scannen (Photo Scan). 4.
Opmerking In het pop-upmenu kunt u e-mailclients voor bijlagen toevoegen. Als Geen (handmatig toevoegen) (None (Attach Manually)) is geselecteerd, moet u gescande en opgeslagen afbeeldingen handmatig toevoegen aan een e-mail. 5. Klik op OK. Het hoofdvenster IJ Scan Utility verschijnt. Opmerking Zie de volgende pagina's voor meer informatie over instellingsitems in het dialoogvenster Instellingen.
Dialoogvenster Instellingen (Automatisch scannen) Dialoogvenster Instellingen (Foto scannen) Dialoogvenster Instellingen (Document scannen) Dialoogvenster Instellingen (Aangepast scannen) Dialoogvenster Instellingen (ScanGear) 6. Klik op Foto (Photo). Het scannen begint. Na afloop van het scannen wordt de gespecificeerde e-mailclient gestart en worden de afbeeldingen aan een nieuw bericht toegevoegd. Opmerking Klik op Annuleren (Cancel) om het scannen te annuleren.
Tekst extraheren van gescande afbeeldingen (OCR) U kunt tekst in gescande tijdschriften en kranten scannen en weergeven in TextEdit (geleverd bij Mac OS). Opmerking U kunt tekst extraheren tijdens het scannen via Document, Aangepast (Custom) of ScanGear. De vensters voor het scannen van documenten worden in de volgende beschrijvingen als voorbeeld gebruikt. 1. Start IJ Scan Utility. IJ Scan Utility starten 2. Klik op Instellingen (Settings...). Het dialoogvenster Instellingen wordt weergegeven.
Opmerking Als u My Image Garden opgeeft, wordt de tekst in de afbeelding, nadat de afbeelding is gescand, geëxtraheerd en weergegeven in TextEdit (geleverd bij Mac OS). 5. Klik op OK. Het hoofdvenster IJ Scan Utility verschijnt. Opmerking Zie de volgende pagina's voor meer informatie over instellingsitems in het dialoogvenster Instellingen.
Dialoogvenster Instellingen (Aangepast scannen) Dialoogvenster Instellingen (ScanGear) 6. Klik op Document. Het scannen begint. Als het scannen is voltooid worden de gescande afbeeldingen opgeslagen volgens de instellingen en verschijnt de geëxtraheerde tekst in de opgegeven toepassing. Opmerking Klik op Annuleren (Cancel) om het scannen te annuleren. Tekst die wordt weergegeven in TextEdit (geleverd bij Mac OS), is alleen als richtlijn bedoeld.
Schermen van IJ Scan Utility Hoofdscherm van IJ Scan Utility Dialoogvenster Instellingen Dialoogvenster Instellingen (Automatisch scannen) Dialoogvenster Instellingen (Foto scannen) Dialoogvenster Instellingen (Document scannen) Dialoogvenster Instellingen (Aangepast scannen) Dialoogvenster Instellingen (Scannen en samenvoegen) Dialoogvenster Instellingen (ScanGear) Dialoogvenster Instellingen (Opslaan naar pc (automatisch)) Dialoogvenster Instellingen (Opslaan naar pc (foto)) Dialoogvenster Instellingen (O
Hoofdscherm van IJ Scan Utility Selecteer Programma's (Applications) in het menu Ga (Go) van de Finder, en dubbelklik achtereenvolgens op de map Canon Utilities, de map IJ Scan Utility en het pictogram Canon IJ Scan Utility om IJ Scan Utility te starten. U kunt in één handeling scannen en opslaan door op het bijbehorende pictogram te klikken. • Productnaam (Product Name) Hier wordt de productnaam weergegeven van het product waar IJ Scan Utility momenteel voor is ingesteld.
Dialoogvenster Instellingen
Dialoogvenster Instellingen Het dialoogvenster Instellingen bestaat uit drie tabbladen: (Scannen vanaf een computer), (Scannen vanaf het bedieningspaneel) en (Algemene instellingen). Als u op een tabblad klikt verandert de weergave in het rode kader en kunt u geavanceerde instellingen voor de functies op elk tabblad opgeven. Tabblad (Scannen vanaf een computer) U kunt opgeven hoe moet worden gereageerd als er wordt gescand vanaf IJ Scan Utility of My Image Garden.
Tabblad (Algemene instellingen) U kunt het te gebruiken product, de beperking van de bestandsgrootte voor e-mailbijlagen, de taal om tekst in afbeeldingen te detecteren en de map waarin de afbeeldingen tijdelijk worden opgeslagen instellen.
Dialoogvenster Instellingen (Automatisch scannen) Klik op Automatisch scannen (Auto Scan) op het tabblad (Scannen vanaf een computer) om het dialoogvenster Instellingen (Automatisch scannen) (Settings (Auto Scan)) weer te geven. In het dialoogvenster Instellingen (Automatisch scannen) (Settings (Auto Scan)) kunt u geavanceerde scaninstellingen opgeven voor het scannen, waarbij het type onderdeel automatisch wordt gedetecteerd.
Opmerking Voor het reduceren van moiré in scans stelt u Bron selecteren (Select Source) in op Tijdschrift (Magazine) in het dialoogvenster Instellingen (Document scannen) (Settings (Document Scan)) of Instellingen (Aangepast scannen) (Settings (Custom Scan)) en klikt u op Document of Aangepast (Custom) in het hoofdscherm van IJ Scan Utility.
• Naar een toepassing sturen (Send to an application) Selecteer deze optie wanneer u de gescande afbeeldingen ongewijzigd wilt gebruiken in een toepassing waarmee u door afbeeldingen kunt bladeren of ze kunt organiseren. In het pop-upmenu kunt u de toepassing selecteren. • Naar een map sturen (Send to a folder) Selecteer deze optie wanneer u de gescande afbeeldingen ook wilt opslaan in een andere map dan is opgegeven in Opslaan in (Save in). In het pop-upmenu kunt u de map selecteren.
Dialoogvenster Instellingen (Foto scannen) Klik op Foto scannen (Photo Scan) op het tabblad (Scannen vanaf een computer) om het dialoogvenster Instellingen (Foto scannen) (Settings (Photo Scan)) weer te geven. In het dialoogvenster Instellingen (Foto scannen) (Settings (Photo Scan)) kunt u geavanceerde scaninstellingen opgeven.
Selecteer de grootte van het item dat u wilt scannen. Wanneer u Aangepast (Custom) selecteert, wordt een dialoogvenster geopend waarin u het papierformaat kunt opgeven. Selecteer een Eenheid (Unit), voer de Breedte (Width) en Hoogte (Height) in en klik vervolgens op OK. Opmerking Klik op Standaard (Defaults) om de opgegeven instellingen te herstellen naar de standaardinstellingen. • Resolutie (Resolution) Selecteer de resolutie van het item dat u wilt scannen.
De standaardmap voor het opslaan van bestanden is de map Documenten (Documents). Belangrijk Als het dialoogvenster Instellingen wordt weergegeven vanuit My Image Garden wordt deze optie niet weergegeven. • Scanresultaten controleren (Check scan results) Hiermee geeft u het dialoogvenster Instellingen opslaan (Save Settings) na het scannen weer. Dialoogvenster Instellingen opslaan Belangrijk Als het dialoogvenster Instellingen wordt weergegeven vanuit My Image Garden wordt deze optie niet weergegeven.
Dialoogvenster Instellingen (Document scannen) Klik op Document scannen (Document Scan) op het tabblad (Scannen vanaf een computer) om het dialoogvenster Instellingen (Document scannen) (Settings (Document Scan)) weer te geven. In het dialoogvenster Instellingen (Document scannen) (Settings (Document Scan)) kunt u geavanceerde scaninstellingen voor het scannen van items als documenten opgeven.
Wanneer Document (ADF/glasplaat) (Document (ADF/Platen)) is geselecteerd en documenten op de plaat en de ADF worden geplaatst, worden de documenten gescand die op de ADF zijn geplaatst. • Kleurenmodus (Color Mode) Hier kunt u de kleurenmodus selecteren waarmee het item moet worden gescand. Belangrijk Schakel het selectievakje Gescande afbeeldingen bij het overbrengen comprimeren (Compress scanned images upon transfer) uit als u Zwart-wit (Black and White) wilt selecteren.
• Instellingen voor het verwerken van afbeeldingen (Image Processing Settings) Klik op (pijl naar rechts) om het volgende in te stellen. Opmerking De weergegeven items hangen af van Bron selecteren (Select Source) en Kleurenmodus (Color Mode). • Automatische documentcorrectie toepassen (Apply Auto Document Fix) Schakel dit selectievakje in om tekst in een document of tijdschrift scherper te maken en zo de leesbaarheid ervan te verbeteren.
Documenten met een zeer groot of zeer klein lettertype Documenten met weinig tekst Documenten met illustraties/afbeeldingen Handschrift Documenten met zowel verticale als horizontale lijnen (tabellen) Opmerking Het scannen neemt meer tijd in beslag als u Scheve tekstdocumenten corrigeren (Correct slanted text document) inschakelt.
• Scanresultaten controleren (Check scan results) Hiermee geeft u het dialoogvenster Instellingen opslaan (Save Settings) na het scannen weer. Dialoogvenster Instellingen opslaan Belangrijk Als het dialoogvenster Instellingen wordt weergegeven vanuit My Image Garden wordt deze optie niet weergegeven. (3) Gebied Instellingen voor de toepassing • Met een toepassing openen (Open with an application) Selecteer dit wanneer u de gescande afbeeldingen wilt verbeteren of corrigeren.
Dialoogvenster Instellingen (Aangepast scannen) Klik op Aangepast scannen (Custom Scan) op het tabblad (Scannen vanaf een computer) om het dialoogvenster Instellingen (Aangepast scannen) (Settings (Custom Scan)) weer te geven. In het dialoogvenster Instellingen (Aangepast scannen) (Settings (Custom Scan)) kunt u geavanceerde scaninstellingen voor het scannen volgens uw voorkeur opgeven.
Tekstdocumenten kleiner dan 2L (127 x 178 mm) (5 x 7 inch), zoals pagina's van een pocket waarvan de rug is afgesneden Items die zijn afgedrukt op dun wit papier Lange, smalle items, zoals panoramafoto's Reflecterende disclabels worden mogelijk niet zoals verwacht gescand. Plaats de items op de juiste manier op de plaat, afhankelijk van het type item dat u wilt scannen. Anders worden de items mogelijk niet goed gescand.
Belangrijk Inbindzijde (Binding Side) kan niet worden opgegeven als alleen de voorzijde van elk document wordt gescand. • Gescande afbeeldingen bij het overbrengen comprimeren (Compress scanned images upon transfer) Comprimeert gescande afbeeldingen wanneer deze worden overgebracht naar een computer. Dit is handig als uw scanner of printer en computer via een langzame interface zijn aangesloten zoals USB1.1.
Alleen beschikbaar wanneer het selectievakje Gescande afbeeldingen bij het overbrengen comprimeren (Compress scanned images upon transfer) niet is geselecteerd. De kleurtint kan afwijken van de bronafbeelding nadat de correcties zijn toegepast. Schakel in dat geval het selectievakje uit en voer de scan uit. Opmerking Het scannen neemt meer tijd in beslag als u deze functie inschakelt. • Contouren scherper maken (Sharpen outline) Versterkt de contouren van onderwerpen om de afbeelding scherper te maken.
Belangrijk Alleen tekstdocumenten geschreven in een taal die beschikbaar is voor selectie bij Documenttaal (Document Language) in het dialoogvenster Instellingen (Algemene instellingen) (Settings (General Settings)) worden ondersteund. Dialoogvenster Instellingen (Algemene instellingen) De afdrukstand van de volgende typen instellingen of documenten wordt mogelijk niet gedetecteerd, aangezien de tekst niet correct kan worden gedetecteerd.
Dit verschijnt niet wanneer Bron selecteren (Select Source) is ingesteld op Automatisch (Auto). Als het dialoogvenster Instellingen wordt weergegeven vanuit My Image Garden wordt deze optie niet weergegeven. (3) Gebied Instellingen voor de toepassing • Met een toepassing openen (Open with an application) Selecteer dit wanneer u de gescande afbeeldingen wilt verbeteren of corrigeren. In het pop-upmenu kunt u de toepassing selecteren.
Dialoogvenster Instellingen (Scannen en samenvoegen) Klik op Scannen en samenvoegen (Scan and Stitch) op het tabblad (Scannen vanaf een computer) om het dialoogvenster Instellingen (Scannen en samenvoegen) (Settings (Scan and Stitch)) weer te geven. In het dialoogvenster Instellingen (Scannen en samenvoegen) (Settings (Scan and Stitch)) kunt u geavanceerde scaninstellingen opgeven voor het scannen van items die groter zijn dan de plaat.
Hoe hoger de resolutie (waarde), hoe gedetailleerder de afbeelding. Resolutie • Instellingen voor het verwerken van afbeeldingen (Image Processing Settings) Klik op (pijl naar rechts) om het volgende in te stellen. De beschikbare items die u kunt instellen variëren volgens Bron selecteren (Select Source). Belangrijk Wanneer Kleurenmodus (Color Mode) staat ingesteld op Zwart-wit (Black and White) is Instellingen voor het verwerken van afbeeldingen (Image Processing Settings) niet beschikbaar.
Hiermee geeft u het dialoogvenster Instellingen opslaan (Save Settings) na het scannen weer. Dialoogvenster Instellingen opslaan Belangrijk Als het dialoogvenster Instellingen wordt weergegeven vanuit My Image Garden wordt deze optie niet weergegeven. (3) Gebied Instellingen voor de toepassing • Met een toepassing openen (Open with an application) Selecteer dit wanneer u de gescande afbeeldingen wilt verbeteren of corrigeren. In het pop-upmenu kunt u de toepassing selecteren.
Dialoogvenster Instellingen (ScanGear) Klik op ScanGear op het tabblad (Scannen vanaf een computer) om het dialoogvenster Instellingen (ScanGear) (Settings (ScanGear)) weer te geven. In het dialoogvenster Instellingen (ScanGear) (Settings (ScanGear)) kunt u aangeven hoe afbeeldingen moeten worden opgeslagen nadat u deze hebt gescand met ScanGear (scannerstuurprogramma) en hoe er moet worden gereageerd nadat afbeeldingen zijn opgeslagen.
• Instellingen (Settings...) Klik om het dialoogvenster Instellingen voor gegevensindeling (Data Format Settings) weer te geven. Hierin kunt u de kwaliteit instellen van de afbeeldingen die u wilt opslaan, zoeken op trefwoorden in PDF-bestanden en het type compressie inschakelen, en de gegevensindeling opgeven waarin de afbeeldingen moeten worden opgeslagen die u hebt gescand met Automatisch scannen.
• Geen toepassing starten (Do not start any application) De scan wordt opgeslagen in de map die is opgegeven in Opslaan in (Save in). Opmerking Geef het programma of de map op in het dialoogvenster dat wordt weergeven als u Toevoegen... (Add...) selecteert in het pop-upmenu. • Instructies (Instructions) Deze handleiding openen. • Standaard (Defaults) U kunt de instellingen in het getoonde scherm herstellen naar de standaardinstellingen.
Dialoogvenster Instellingen (Opslaan naar pc (automatisch)) Klik op Opslaan naar pc (automatisch) (Save to PC (Auto)) op het tabblad (Scannen vanaf het bedieningspaneel) om het dialoogvenster Instellingen (Opslaan naar pc (automatisch)) (Settings (Save to PC (Auto))) weer te geven.
• Instellingen voor het verwerken van afbeeldingen (Image Processing Settings) Klik op (pijl naar rechts) om het volgende in te stellen. • Aanbevolen afbeeldingscorrectie toepassen (Apply recommended image correction) Past geschikte correcties automatisch toe op basis van het type item. Belangrijk De kleurtint kan afwijken van de bronafbeelding nadat de correcties zijn toegepast. Schakel in dat geval het selectievakje uit en voer de scan uit.
De scan wordt opgeslagen in de map die is opgegeven in Opslaan in (Save in). Opmerking Geef het programma of de map op in het dialoogvenster dat wordt weergeven als u Toevoegen... (Add...) selecteert in het pop-upmenu. • Instructies (Instructions) Deze handleiding openen. • Standaard (Defaults) U kunt de instellingen in het getoonde scherm herstellen naar de standaardinstellingen.
Dialoogvenster Instellingen (Opslaan naar pc (foto)) Klik op Opslaan naar pc (foto) (Save to PC (Photo)) op het tabblad (Scannen vanaf het bedieningspaneel) om het dialoogvenster Instellingen (Opslaan naar pc (foto)) (Settings (Save to PC (Photo))) weer te geven. In het dialoogvenster Instellingen (Opslaan naar pc (foto)) (Settings (Save to PC (Photo))) kunt u aangeven hoe er moet worden gereageerd als u afbeeldingen als foto's opslaat op een computer nadat u deze hebt gescand vanaf het bedieningspaneel.
(2) Gebied Instellingen opslaan • Bestandsnaam (File Name) Voer een bestandsnaam in voor de afbeelding die u wilt opslaan. Wanneer u een bestand opslaat, worden de datum en vier cijfers aan de ingestelde bestandsnaam toegevoegd in de indeling "_20XX0101_0001". • Gegevensindeling (Data Format) Dit stelt u in vanuit het bedieningspaneel. • Instellingen (Settings...) Klik om het dialoogvenster Instellingen voor gegevensindeling (Data Format Settings) weer te geven.
Dialoogvenster Instellingen (Opslaan naar pc (document)) Klik op Opslaan naar pc (document) (Save to PC (Document)) op het tabblad (Scannen vanaf het bedieningspaneel) om het dialoogvenster Instellingen (Opslaan naar pc (document)) (Settings (Save to PC (Document))) weer te geven.
• Gescande afbeeldingen bij het overbrengen comprimeren (Compress scanned images upon transfer) Comprimeert gescande afbeeldingen wanneer deze worden overgebracht naar een computer. Dit is handig als uw scanner of printer en computer via een langzame interface zijn aangesloten zoals USB1.1. • Instellingen voor het verwerken van afbeeldingen (Image Processing Settings) Klik op (pijl naar rechts) om het volgende in te stellen.
Het scannen neemt meer tijd in beslag als u Scheve tekstdocumenten corrigeren (Correct slanted text document) inschakelt. • De afdrukstand van tekstdocumenten detecteren en afbeeldingen roteren (Detect the orientation of text document and rotate image) Roteert de afbeelding automatisch naar de juiste afdrukstand door de afdrukstand van tekst in het gescande document te detecteren.
Geef het programma of de map op in het dialoogvenster dat wordt weergeven als u Toevoegen... (Add...) selecteert in het pop-upmenu. • Instructies (Instructions) Deze handleiding openen. • Standaard (Defaults) U kunt de instellingen in het getoonde scherm herstellen naar de standaardinstellingen.
Dialoogvenster Instellingen (Algemene instellingen) Klik op het tabblad (Algemene instellingen) om het dialoogvenster Instellingen (Algemene instellingen) (Settings (General Settings)) weer te geven. U kunt het te gebruiken product, de beperking van de bestandsgrootte voor e-mailbijlagen, de taal om tekst in afbeeldingen te detecteren en de map waarin de afbeeldingen tijdelijk worden opgeslagen instellen in het dialoogvenster Instellingen (Algemene instellingen) (Settings (General Settings)).
U kunt de instellingen in het getoonde scherm herstellen naar de standaardinstellingen.
Dialoogvenster Instellingen voor gegevensindeling Geef het dialoogvenster Instellingen voor gegevensindeling (Data Format Settings) weer op een van de volgende manieren. • Klik op Instellingen... (Settings...) bij Instellingen opslaan (Save Settings) op elk tabblad van het dialoogvenster Instellingen. • Klik op Instellingen... (Settings...
• Indeling voor een item dat als een document in Automatisch scannen wordt gedetecteerd (Format for Item Detected as Document in Auto Scan) U kunt de gegevensindeling opgeven voor het automatisch opslaan van items die als documenten worden gedetecteerd in Automatisch scannen.
Dialoogvenster Instellingen opslaan Selecteer het selectievakje Scanresultaten controleren (Check scan results) in Instellingen opslaan (Save Settings) van het dialoogvenster Instellingen om na het scannen het dialoogvenster Instellingen opslaan (Save Settings) weer te geven. U kunt de gegevensindeling en de bestemming opgeven terwijl u de miniaturen van scanresultaten weergeeft.
(3) Gebied Instellingen opslaan • Bestandsnaam (File Name) Voer een bestandsnaam in voor de afbeelding die u wilt opslaan. Wanneer u een bestand opslaat, worden de datum en vier cijfers aan de ingestelde bestandsnaam toegevoegd in de indeling "_20XX0101_0001". • Gegevensindeling (Data Format) Selecteer de gegevensindeling waarin de gescande documenten moeten worden opgeslagen. U kunt JPEG/Exif, TIFF, PNG, PDF of PDF (meerdere pagina's) (PDF (Multiple Pages)) selecteren.
Venster Afbeelding samenvoegen Klik op Samenvoegen (Stitch) in het hoofdscherm van IJ Scan Utility om het venster Afbeelding samenvoegen (Image Stitch) weer te geven. U kunt de linker- en rechterhelft van een item dat groter is dan de plaat scannen en deze tot één afbeelding samenvoegen. U kunt items scannen die maximaal ongeveer twee keer zo groot zijn dan de glasplaat.
Geeft de eerste gescande afbeelding aan de rechterkant weer. • Afbeelding 1 scannen (Scan Image 1) • Start het scannen van afbeelding 1 (Start Scanning Image 1) Scant het eerste item. • Afbeelding 2 scannen (Scan Image 2) • Start het scannen van afbeelding 2 (Start Scanning Image 2) Scant het tweede item. • Bijsnijdkaders aanpassen (Adjust cropping frames) U kunt het scangebied aanpassen in het voorbeeld.
• Opslaan (Save) De twee gescande afbeeldingen worden als één afbeelding opgeslagen. • Annuleren (Cancel) Annuleert Samenvoegen (Stitch) scan. (2) Werkbalk • Werkbalk U kunt de gescande afbeeldingen verwijderen of de voorbeeldafbeeldingen aanpassen. • (Verwijderen) Hiermee verwijdert u de gescande afbeelding. • (Vergroten/verkleinen) Hiermee vergroot of verkleint u de voorbeeldafbeelding. Door met de linkermuisknop te klikken in het Voorbeeldgebied wordt de getoonde afbeelding vergroot.
• Na het scannen van het eerste item door te klikken op Start het scannen van afbeelding 1 (Start Scanning Image 1) De afbeelding wordt gescand in de richting die is opgegeven in Richting selecteren (Scan Direction), en 2 verschijnt ernaast. • Na het scannen van het tweede item door te klikken op Start het scannen van afbeelding 2 (Start Scanning Image 2) De twee gescande afbeeldingen worden weergegeven.
Scannen met een toepassing die u gebruikt (ScanGear) Wat is ScanGear (scannerstuurprogramma)? Scannen met geavanceerde instellingen met ScanGear (scannerstuurprogramma) ScanGear (scannerstuurprogramma) starten Scannen in de Basismodus Scannen in de Geavanceerde modus Meerdere documenten tegelijk scannen vanuit de ADF (automatische documentinvoer) in de Geavanceerde modus Meerdere documenten tegelijk scannen met ScanGear (scannerstuurprogramma) Afbeeldingen corrigeren en kleuren aanpassen met ScanGear (scann
Wat is ScanGear (scannerstuurprogramma)? ScanGear (scannerstuurprogramma) is software die nodig is voor het scannen van documenten. U kunt hiermee het uitvoerformaat opgeven en afbeeldingen corrigeren wanneer u documenten scant. ScanGear kan worden gestart vanuit My Image Garden of IJ Scan Utility. ScanGear kan ook worden gestart vanuit andere toepassingen die compatibel zijn met de standaardinterface genaamd TWAIN. (ScanGear is een TWAIN-compatibel stuurprogramma.
Scannen met geavanceerde instellingen met ScanGear (scannerstuurprogramma) ScanGear (scannerstuurprogramma) starten ScanGear (scannerstuurprogramma) starten Documenten scannen nadat u eenvoudige afbeeldingscorrecties hebt aangebracht Scannen in de Basismodus Documenten scannen nadat u geavanceerde afbeeldingscorrecties hebt toegepast en de helderheid/kleur hebt aangepast Scannen in de Geavanceerde modus Meerdere documenten tegelijk scannen vanuit de ADF (automatische documentinvoer) na het maken van geavanc
ScanGear (scannerstuurprogramma) starten Met ScanGear (scannerstuurprogramma) kunt u bij het scannen afbeeldingscorrecties en kleuraanpassingen aanbrengen. ScanGear kan worden gestart vanuit My Image Garden of een toepassing. Opmerking Installeer de netwerkomgeving als u meer dan één scanner of een netwerkscanner hebt, en de verbinding van een USB-verbinding in een netwerkverbinding hebt veranderd. Starten vanuit My Image Garden Volg deze stappen om ScanGear te starten vanuit My Image Garden. 1.
Scannen in de Basismodus Via het tabblad Basismodus (Basic Mode) kunt u gemakkelijk scannen aan de hand van de weergegeven stappen. Raadpleeg 'Meerdere documenten tegelijk scannen met ScanGear (scannerstuurprogramma)' voor informatie over het scannen van meerdere documenten tegelijk op de glasplaat. Bij het scannen vanuit de ADF (automatische documentinvoer) worden de documenten gescand zonder eerst een voorbeeld weer te geven. Belangrijk De volgende documenttypen worden mogelijk niet correct gescand.
Opmerking Wanneer u tijdschriften scant die veel kleurenfoto's bevatten, selecteert u Tijdschrift (kleur) (Magazine (Color)). Wanneer u een model gebruikt dat is uitgerust met een automatisch dubbelzijdige ADF, kunt u opgeven hoe het papier moet worden uitgevoerd na het scannen van beide zijden vanuit de ADF in ADF Dubbelzijdig Instellingen voor papieruitvoer (ADF Duplex Paper Output Settings) op het tabblad Scannen (Scan) van het dialoogvenster Voorkeuren (Preferences). Tabblad Scannen 3.
Het scannen begint. Opmerking Klik op (Informatie) om een dialoogvenster te openen waarin u de huidige scan-instellingen (documenttype etc.) kunt controleren. Bij Status van het dialoogvenster ScanGear na het scannen (Status of ScanGear dialog after scanning) op het tabblad Scannen (Scan) van het dialoogvenster Voorkeuren (Preferences) kunt u de reactie van ScanGear opgeven.
Scannen in de Geavanceerde modus Op het tabblad Geavanceerde modus (Advanced Mode) kunt u de kleurenmodus, uitvoerresolutie, helderheid, kleurtint en dergelijke voor de scan instellen. Raadpleeg 'Meerdere documenten tegelijk scannen met ScanGear (scannerstuurprogramma)' voor informatie over het scannen van meerdere documenten tegelijk.
4. Klik op Voorbeeld (Preview). Er verschijnt een scanvoorbeeld van het document in het voorbeeldgebied. 5. Stel de Instellingen voor uitvoer (Output Settings) in. Instellingen voor uitvoer 6. Stel het bijsnijdkader (scangebied) in en breng desgewenst afbeeldingscorrecties en kleuraanpassingen aan. Bijsnijdkaders aanpassen (ScanGear) Instellingen voor afbeeldingen Knoppen voor kleuraanpassing 7. Klik op Scannen (Scan). Het scannen begint.
Meerdere documenten tegelijk scannen vanuit de ADF (automatische documentinvoer) in de Geavanceerde modus U kunt op het tabblad Geavanceerde modus (Advanced Mode) de helderheid, kleurtint, enzovoort, van afbeeldingen opgeven, en meerdere documenten tegelijk vanuit de ADF (automatische documentinvoer) scannen. Wanneer u een model gebruikt dat is uitgerust met een automatisch dubbelzijdige ADF, kunt u beide kanten van documenten automatisch met de ADF scannen.
in ADF Dubbelzijdig Instellingen voor papieruitvoer (ADF Duplex Paper Output Settings) op het tabblad Scannen (Scan) van het dialoogvenster Voorkeuren (Preferences). Tabblad Scannen 4. Stel de Instellingen voor uitvoer (Output Settings) in. Instellingen voor uitvoer 5. Breng naar wens afbeeldingscorrecties en kleuraanpassingen aan. Instellingen voor afbeeldingen Knoppen voor kleuraanpassing 6. Klik op Scannen (Scan). Het scannen begint.
Meerdere documenten tegelijk scannen met ScanGear (scannerstuurprogramma) U kunt twee of meer foto's (kleine documenten) op de glasplaat tegelijk scannen via het tabblad Basismodus (Basic Mode) of Geavanceerde modus (Advanced Mode). In dit gedeelte wordt uitgelegd hoe u meerdere documenten kunt scannen vanaf het tabblad Basismodus (Basic Mode). Belangrijk Als u meerdere documenten als één afbeelding wilt scannen, scant u in de volledige afbeeldingsweergave.
3. Klik op Voorbeeld (Preview). In het voorbeeldgebied worden miniaturen van de voorbeeldafbeeldingen weergegeven. Bijsnijdkaders worden automatisch aangegeven op basis van het documentformaat. 4. Selecteer Doel (Destination). 5. Stel Uitvoerformaat (Output Size) in, afhankelijk van het doel. 6. Pas desgewenst de bijsnijdkaders aan en stel Afbeeldingscorrecties (Image corrections) in. Opmerking U kunt elke afbeelding afzonderlijk corrigeren. Selecteer het kader dat u wilt corrigeren.
7. Selecteer de afbeeldingen die u wilt scannen. Schakel de selectievakjes in voor de afbeeldingen die u wilt scannen. 8. Klik op Scannen (Scan). Meerdere documenten scannen in de volledige afbeeldingsweergave Volg deze stappen als miniaturen niet correct worden weergegeven in de voorbeeldweergave of als u meerdere documenten als één afbeelding wilt scannen. Opmerking De positie van scheef geplaatste documenten wordt niet gecorrigeerd in de volledige afbeeldingsweergave. 1.
Pas de grootte en de positie van de bijsnijdkaders aan in de voorbeeldafbeelding. U kunt ook twee of meer bijsnijdkaders maken. Als een gebied niet is opgegeven, wordt het document gescand op documentformaat (Automatisch bijsnijden). Wanneer een gebied is geselecteerd, wordt alleen het geselecteerde gebied gescand. Bijsnijdkaders aanpassen (ScanGear) 5. Stel de gewenste Afbeeldingscorrecties (Image corrections) in. 6. Klik op Scannen (Scan).
Afbeeldingen corrigeren en kleuren aanpassen met ScanGear (scannerstuurprogramma) Onscherpe foto's scherper maken, stof en krassen reduceren en vervaagde kleuren corrigeren Afbeeldingen corrigeren (Beeld verscherpen, Stof en krassen reduceren, Correctie van vervaging, enzovoort) Een voorbeeld bekijken en de kleur wijzigen van de afbeelding die wordt gescand Kleuren aanpassen met een kleurenpatroon Kleuren helderder maken die in de loop der tijd of als gevolg van overkleuring zijn vervaagd Verzadiging en kle
Afbeeldingen corrigeren (Beeld verscherpen, Stof en krassen reduceren, Correctie van vervaging, enzovoort) Met de functies van Instellingen voor afbeeldingen (Image Settings) op het tabblad Geavanceerde modus (Advanced Mode) van ScanGear (scannerstuurprogramma) kunt u bij het scannen van afbeeldingen de contouren van het onderwerp verscherpen, stof en krassen verminderen en vervaagde kleuren corrigeren. Items instellen Klik op (pijl) van een functie en selecteer een item in het pop-upmenu.
Doorschijneffecten reduceren in tekstdocumenten of de basiskleur lichter maken voor bijvoorbeeld gerecycled papier en kranten bij het scannen van documenten Stel Doorschijnendheid beperken (Reduce Show-through) in op AAN (ON). UIT (OFF) AAN (ON) Afbeeldingen verscherpen die niet helemaal scherp zijn Stel Beeld verscherpen (Unsharp Mask) in op AAN (ON). UIT (OFF) AAN (ON) Gradaties en streeppatronen verminderen Stel Moiré-reductie (Descreen) in op AAN (ON).
Geen (None) Middel (Medium) Foto's corrigeren die in de loop der tijd of als gevolg van overkleuring zijn vervaagd Stel Correctie van vervaging (Fading Correction) in op Laag (Low), Middel (Medium) of Hoog (High), afhankelijk van de mate van vervaging of overkleuring. Geen (None) Middel (Medium) Korreligheid verminderen Stel Correctie van korreligheid (Grain Correction) in op Laag (Low), Middel (Medium) of Hoog (High), afhankelijk van de mate van de korreligheid.
Kleuren aanpassen met een kleurenpatroon Met de functie Kleurenpatroon op het tabblad Basismodus (Basic Mode) van ScanGear (scannerstuurprogramma) kunt u voorbeelden van kleurwijzigingen bekijken en natuurlijke kleuren reproduceren. Kleuraanpassing Hiermee kunt u kleuren corrigeren die in de loop der tijd of als gevolg van overkleuring zijn vervaagd. Overkleuring' is het verschijnsel waarbij een bepaalde kleur de gehele foto beïnvloedt als gevolg van de weersomstandigheden of sterke omgevingskleuren.
Het beste kunt u een gedeelte op de foto zoeken dat wit zou moeten zijn, en de kleuren zo aanpassen dat dit gedeelte wit wordt. Er verschijnt een scanvoorbeeld van het document in het midden. De kleuren van het voorbeeld veranderen met uw aanpassingen mee. Hieronder ziet u een voorbeeld van het corrigeren van een blauwige afbeelding. Omdat Blauw (Blue) en Groen (Green) te sterk zijn, klikt u op de pijlen bij de kleuren Geel (Yellow) en Magenta om de kleur te corrigeren.
Verzadiging en kleurbalans aanpassen Klik op het tabblad Geavanceerde modus (Advanced Mode) van ScanGear (stuurprogramma) op (Verzadiging/kleurbalans). Opmerking Klik op Standaard (Defaults) om alle aanpassingen in het huidige venster ongedaan te maken. Verzadiging De verzadiging (levendigheid) van de afbeelding aanpassen. U kunt kleuren helderder maken die in de loop der tijd of door andere oorzaken zijn vervaagd.
Magenta en groen Geel en blauw Dit zijn de complementaire kleuren (als de twee kleuren van een kleurenpaar worden gemengd, ontstaat een grijstint). U kunt de natuurlijke kleuren van een fotosituatie reproduceren door de te veel benadrukte kleur te verminderen en de complementaire kleur te verhogen. Het is vaak lastig om de afbeelding helemaal te corrigeren door slechts één kleurenpaar aan te passen.
Helderheid en contrast aanpassen Klik op het tabblad Geavanceerde modus (Advanced Mode) van ScanGear (stuurprogramma) op (Helderheid/contrast). Opmerking Klik op (pijl omlaag) om over te schakelen naar de gedetailleerde weergave. Klik op (pijl omhoog) om terug te keren naar de vorige weergave. Klik op Standaard (Defaults) om alle aanpassingen in het huidige venster ongedaan te maken. Kanaal Iedere punt van een afbeelding is een mengsel van rood, groen en blauw in verschillende verhoudingen (gradaties).
Helderheid (schuifknop) onder Helderheid (Brightness) naar Pas de helderheid van de afbeelding aan. Sleep links om de afbeelding donkerder te maken en naar rechts om deze lichter te maken. U kunt ook een waarde invoeren (-127 tot 127). Donkerder Originele afbeelding Lichter Opmerking Als u de afbeelding te licht maakt kunnen de lichte gebieden verloren gaan, en als u de afbeelding te donker maakt kan dit ten koste gaan van de schaduwgebieden.
Histogram aanpassen Klik op het tabblad Geavanceerde modus (Advanced Mode) van ScanGear (stuurprogramma) op (Histogram). Opmerking Klik op Standaard (Defaults) om alle aanpassingen in het huidige venster ongedaan te maken. Kanaal Iedere punt van een afbeelding is een mengsel van rood, groen en blauw in verschillende verhoudingen (gradaties). Deze kleuren kunnen afzonderlijk worden aangepast als een 'kanaal'. • Model (Master) Rood, groen en blauw aanpassen. • Rood (Red) Het rode kanaal aanpassen.
In het lichte gebied zijn meer gegevens verdeeld. In het schaduwgebied zijn meer gegevens verdeeld. De gegevens zijn gelijk verdeeld tussen het lichte gebied en het schaduwgebied. Histogrammen aanpassen (met de schuifknop) Selecteer een Kanaal (Channel) en versleep (schuifknop voor zwartpunt) of (schuifknop voor witpunt) om het niveau op te geven dat moet worden ingesteld als schaduwen of hoge lichten. - Alle gedeelten links van (schuifknop voor zwartpunt) worden zwart (niveau 0).
Afbeeldingen waarin in het lichte gebied meer gegevens zijn verdeeld Sleep de schuifknop voor middenpunt naar het lichte gebied. Afbeeldingen waarin in het schaduwgebied meer gegevens zijn verdeeld Sleep de schuifknop voor middenpunt naar het schaduwgebied. Histogrammen aanpassen (met de pipetten) Als u een Kanaal (Channel) selecteert en op de pipet voor zwartpunt, middenpunt of witpunt klikt, verandert de muisaanwijzer in de voorbeeldweergave in een pipet.
Tintcurve aanpassen Klik op het tabblad Geavanceerde modus (Advanced Mode) van ScanGear (stuurprogramma) op (Tintcurve-instellingen). Opmerking Klik op Standaard (Defaults) om alle aanpassingen in het huidige venster ongedaan te maken. Kanaal Iedere punt van een afbeelding is een mengsel van rood, groen en blauw in verschillende verhoudingen (gradaties). Deze kleuren kunnen afzonderlijk worden aangepast als een 'kanaal'. • Model (Master) Rood, groen en blauw aanpassen.
Tintcurve aanpassen Selecteer in Tintcurve selecteren (Select Tone Curve) een tintcurve in Geen correctie (No correction), Overbelichting (Overexposure), Onderbelichting (Underexposure), Veel contrast (High contrast), Negatief/positief beeld omdraaien (Reverse the negative/positive image) en Aangepaste curve bewerken (Edit custom curve).
Aangepaste curve bewerken (Edit custom curve) U kunt bepaalde punten op de tintcurve slepen, zodat u de helderheid van de bijbehorende gebieden naar wens kunt aanpassen.
Drempel instellen De helderheid van kleurenafbeeldingen en afbeeldingen in grijswaarden wordt uitgedrukt in een waarde tussen 0 en 255. Bij het maken van zwart-wit afbeeldingen worden echter alle kleuren omgezet in zwart (0) of wit (255). De drempel is de grenswaarde die bepaalt of een kleur zwart of wit wordt. Door het drempelniveau aan te passen, kunt u de tekst in een document scherper maken en voorkomen dat tekst op de achterzijde van het papier doorschijnt (wat vooral bij en gebeurt).
Schermen van ScanGear (scannerstuurprogramma) Tabblad Basismodus Tabblad Geavanceerde modus Instellingen voor invoer Instellingen voor uitvoer Instellingen voor afbeeldingen Knoppen voor kleuraanpassing Dialoogvenster Voorkeuren Tabblad Scanner Tabblad Voorbeeld Tabblad Scannen Tabblad Kleurinstellingen
Tabblad Basismodus In deze modus kunt u eenvoudig scannen door de instructies op het scherm te volgen. In dit gedeelte worden instellingen en functies beschreven die beschikbaar zijn op het tabblad Basismodus (Basic Mode). Bij het scannen vanuit de ADF (automatische documentinvoer) worden de documenten gescand zonder eerst een voorbeeld weer te geven.
• Document (grijstinten) ADF dubbelzijdig (Document (Grayscale) ADF Duplex) (alleen modellen met Automatisch dubbelzijdig ADF) Beide zijden van documenten in zwart-wit scannen vanuit de ADF. Documenten worden gescand om in de lengte te worden gebonden, waarbij het uiteinde wordt ingevoerd in de ADF als het bovenste uiteinde. Belangrijk Het doorlopend scannen vanuit de ADF wordt niet door alle toepassingen ondersteund. Raadpleeg de handleiding van de toepassing voor meer informatie.
Hiermee kunt u de bijsnijdkaders (scangebieden) naar wens aanpassen. In miniaturenweergave Sleep de muis over een miniatuur om een bijsnijdkader weer te geven. Wanneer een bijsnijdkader wordt weergegeven, wordt het gedeelte in het bijsnijdkader gescand. Als er geen bijsnijdkader wordt weergegeven, wordt elk kader afzonderlijk gescand. In volledige afbeeldingsweergave Wanneer er geen bijsnijdkader wordt weergegeven, wordt het hele voorbeeldgebied gescand.
Opmerking Als u wilt weten of en hoe het bijsnijdkader aanvankelijk wordt weergegeven in een voorbeeldafbeelding, raadpleegt u Kader van voorbeeldafbeelding bijsnijden (Cropping Frame on Previewed Images) op het 'Tabblad Voorbeeld' (dialoogvenster Voorkeuren (Preferences)). • Verhouding omkeren (Invert aspect ratio) Beschikbaar wanneer bij Uitvoerformaat (Output Size) een andere optie dan Aanpasbaar (Flexible) is geselecteerd. Klik op deze knop om het bijsnijdkader te draaien.
Start met scannen. Opmerking Wanneer het scannen begint, wordt de voortgang weergegeven. Klik op Annuleren (Cancel) om de scan te annuleren. • Voorkeuren... (Preferences...) Hiermee opent u het dialoogvenster Voorkeuren (Preferences), waarin u instellingen voor scannen en voorbeeld kunt opgeven. Dialoogvenster Voorkeuren • Sluiten (Close) Hiermee sluit u ScanGear (scannerstuurprogramma). (2) Werkbalk • Werkbalk U kunt voorbeeldafbeeldingen aanpassen of roteren.
• (Alle kaders selecteren) Beschikbaar wanneer twee of meer kaders worden weergegeven. Hiermee kunt u de afbeeldingen in de miniaturenweergave selecteren en met een blauw kader omlijnen. • (Alle bijsnijdkaders selecteren) Beschikbaar wanneer er twee of meer bijsnijdkaders zijn opgegeven. Hiermee verandert u de bijsnijdkaders in dikke onderbroken lijnen en worden de instellingen toegepast op alle bijsnijdkaders. • (Bijsnijdkader verwijderen) Hiermee verwijdert u het geselecteerde bijsnijdkader.
Dubbelklik op een kader om in te zoomen op de afbeelding. Klik op (volgend/vorig kader) onder aan het scherm om het vorige of volgende kader weer te geven. Dubbelklik opnieuw op het kader om terug te keren naar de weergave op de oorspronkelijke grootte. Als (volledige afbeelding) wordt weergegeven op de werkbalk De items op de glasplaat worden gescand en als één afbeelding weergegeven. Alle gedeelten binnen de bijsnijdkaders worden gescand.
Tabblad Geavanceerde modus In deze modus kunt u geavanceerde scaninstellingen opgeven, zoals de kleurenmodus, uitvoerresolutie, helderheid van de afbeelding en kleurtint. In dit gedeelte worden instellingen en functies beschreven die beschikbaar zijn op het tabblad Geavanceerde modus (Advanced Mode). Bij het scannen vanuit de ADF (automatische documentinvoer) worden de documenten gescand zonder eerst een voorbeeld weer te geven.
Voer Naam instelling (Setting Name) in en klik op Toevoegen (Add). De naam wordt weergegeven in Lijst met voorkeursinstellingen (Favorite Settings List). Wanneer u op Opslaan (Save) klikt, wordt het item weergegeven in de lijst Voorkeursinstellingen (Favorite Settings) en kan het worden geselecteerd, samen met de vooraf gedefinieerde items. Als u een item wilt verwijderen, selecteert u het item in de Lijst met voorkeursinstellingen (Favorite Settings List) en klikt u op Verwijderen (Delete).
Met In-/uitzoomen (Zoom) wordt het document opnieuw gescand en wordt er in het voorbeeld een afbeelding met een hoge resolutie weergegeven. (Vergroten/Verkleinen) op de werkbalk biedt u de mogelijkheid snel in of uit te zoomen op de voorbeeldafbeelding. De resolutie van de afbeelding die wordt weergegeven, is echter laag. • Voorbeeld (Preview) Een proefscan uitvoeren. • Scannen (Scan) Start met scannen. Opmerking Wanneer het scannen begint, wordt de voortgang weergegeven.
In miniaturenweergave In volledige afbeeldingsweergave • (Miniatuur) / (Hele afbeelding) Hiermee wordt geschakeld tussen weergaven in het voorbeeldgebied. Voorbeeldgebied • (Wissen) Hiermee kunt u de voorbeeldafbeelding uit het voorbeeldgebied verwijderen. Hiermee worden ook de instellingen die met de werkbalk en kleuraanpassing zijn gemaakt, ingesteld op de standaardwaarden. • (Bijsnijden) Hiermee kunt u het scangebied bepalen door met de muis te slepen.
Beschikbaar wanneer twee of meer kaders worden weergegeven. Hiermee kunt u de afbeeldingen in de miniaturenweergave selecteren en met een blauw kader omlijnen. • (Alle bijsnijdkaders selecteren) Beschikbaar wanneer er twee of meer bijsnijdkaders zijn opgegeven. Hiermee verandert u de bijsnijdkaders in dikke onderbroken lijnen en worden de instellingen toegepast op alle bijsnijdkaders. • (Bijsnijdkader verwijderen) Hiermee verwijdert u het geselecteerde bijsnijdkader.
Als (volledige afbeelding) wordt weergegeven op de werkbalk De items op de glasplaat worden gescand en als één afbeelding weergegeven. Alle gedeelten binnen de bijsnijdkaders worden gescand. Opmerking U kunt het bijsnijdkader opgeven in de weergegeven afbeelding. U kunt in de miniaturenweergave maar één bijsnijdkader per afbeelding maken. In de volledige afbeeldingsweergave kunt u meerdere bijsnijdkaders maken.
Instellingen voor invoer Bij Instellingen voor invoer (Input Settings) kunt u de volgende opties instellen: • Bron selecteren (Select Source) Het type document dat wordt gescand wordt weergegeven. Als u wilt scannen vanaf de glasplaat, selecteert u Plaat (Platen). Als u wilt scannen vanuit de ADF (Auto Document Feeder), selecteert u Document (ADF enkelzijdig) (Document (ADF Simplex)) of Document (ADF dubbelzijdig) (Document (ADF Duplex)).
Als u niet zeker weet welk formaat u moet selecteren bij Papierformaat (Paper Size), stelt u het Papierformaat (Paper Size) in op Volledige plaat (Full Platen), meet u het formaat van het document en geeft u de waarden op bij (Breedte) en (Hoogte). • Afdrukstand origineel (Original Orientation) Stel de afdrukstand en de zijde in voor het nieten van de documenten die worden gescand vanuit de ADF. Klik op Instellingen... (Settings...) om het dialoogvenster Afdrukstand (Orientation) te openen.
Instellingen voor het invoerformaat zijn alleen beschikbaar wanneer het Uitvoerformaat (Output Size) in Instellingen voor uitvoer (Output Settings) is ingesteld op Aanpasbaar (Flexible). Als u een ander formaat dan Aanpasbaar (Flexible) selecteert, wordt een bijsnijdkader weergegeven dat is berekend op basis van Uitvoerformaat (Output Size) en Uitvoerresolutie (Output Resolution) en met een vaste verhouding.
Instellingen voor uitvoer Bij Instellingen voor uitvoer (Output Settings) kunt u de volgende opties instellen: • Uitvoerresolutie (Output Resolution) Selecteer de resolutie waarmee u wilt scannen. Hoe hoger de resolutie (waarde), hoe gedetailleerder de afbeelding. Selecteer een van de weergegeven opties voor de resolutie door op de knop te klikken, of typ een waarde (in stappen van 1 dpi). Raadpleeg voor meer informatie 'Resolutie' voor uw model vanuit de startpagina van de Online handleiding.
In volledige afbeeldingsweergave Wanneer er geen bijsnijdkader wordt weergegeven, wordt het hele voorbeeldgebied gescand. Wanneer een bijsnijdkader wordt weergegeven, wordt het gedeelte in het bijsnijdkader gescand. Opmerking Als u de gescande afbeelding wilt vergroten/verkleinen, voert u waarden in bij (Breedte) en (Hoogte) bij Instellingen voor uitvoer (Output Settings) of geeft u een waarde op in procenten bij %.
Raadpleeg 'Bijsnijdkaders aanpassen (ScanGear)' voor meer informatie over bijsnijdkaders. Als u wilt weten of en hoe het bijsnijdkader aanvankelijk wordt weergegeven in een voorbeeldafbeelding, raadpleegt u Kader van voorbeeldafbeelding bijsnijden (Cropping Frame on Previewed Images) op het 'Tabblad Voorbeeld' (dialoogvenster Voorkeuren (Preferences)). • (Lengte-breedteverhouding schakelen) Beschikbaar wanneer bij Uitvoerformaat (Output Size) een andere optie dan Aanpasbaar (Flexible) is geselecteerd.
Instellingen voor afbeeldingen Belangrijk Gebruik deze functies niet voor afbeeldingen zonder moiré, stof/krassen of vervaagde kleuren. De kleurtint kan dan nadelig beïnvloed worden. Resultaten van afbeeldingscorrecties worden mogelijk niet weergegeven in de voorbeeldafbeelding. Opmerking Welke instellingen u kunt selecteren, is afhankelijk van de instellingen voor Kleurenmodus (Color Mode). Het scannen kan langer duren als u Instellingen voor afbeeldingen (Image Settings) gebruikt.
Belangrijk U kunt Beeldaanpassing (Image Adjustment) instellen nadat u het voorbeeld hebt bekeken. U kunt deze instelling wijzigen als Aanbevolen (Recommended) is geselecteerd op het tabblad Kleurinstellingen (Color Settings) van het dialoogvenster Voorkeuren (Preferences). Opmerking Als de afbeelding niet correct wordt aangepast met Automatisch (Auto), moet u het documenttype opgeven. De kleurtint kan afwijken van de bronafbeelding na toepassing van de functie Beeldaanpassing.
• Middel (Medium) Deze instelling wordt aanbevolen. • Hoog (High) Selecteer deze optie om grote stofdeeltjes en krassen te reduceren. Het is echter mogelijk dat het reductieproces zichtbaar blijft of dat fijnere delen van de afbeelding worden verwijderd. Belangrijk Deze instelling heeft mogelijk geen effect bij bepaalde typen foto's. Opmerking U wordt aanbevolen deze optie in te stellen op Geen (None) wanneer u gedrukte materialen scant.
Schaduw van rugmarge wordt niet gecorrigeerd. • Laag (Low) Selecteer deze instelling wanneer het effectniveau met de instelling Middel te sterk is. • Middel (Medium) Deze instelling wordt aanbevolen. • Hoog (High) Selecteer deze instelling wanneer het effectniveau met de instelling Middel te zwak is. Belangrijk Plaats geen items op de glasplaat van 2,0 kg (4,4 lbs) of meer. Oefen ook geen druk van meer dan 2,0 kg (4,4 lbs) uit op het document.
Knoppen voor kleuraanpassing Met de knoppen voor kleuraanpassing kunt u fijne correcties aanbrengen in de helderheid en kleurtonen van de afbeelding, waaronder aanpassingen in de algehele helderheid of het contrast van de afbeelding en wijzigingen in de waarden voor lichte en schaduwgebieden (histogram) of de balans (tintcurve).
In een histogram kunt u de gegevensconcentratie zien op elk helderheidsniveau van een afbeelding. U kunt de helderste niveaus (hoge lichten) en de donkerste niveaus (schaduwen) in een afbeelding opgeven, de niveaus verlagen en het midden van het toonbereik van een afbeelding uitbreiden. Histogram aanpassen • (Tintcurve-instellingen) De helderheid van een afbeelding aanpassen door het type grafiek (tintcurve) te selecteren die de balans van de tintinvoer en -uitvoer aangeeft.
Voer Naam instelling (Setting Name) in en klik op Toevoegen (Add). De naam wordt weergegeven in Lijst met tintcurve-instellingen (Tone Curve Settings List) of Lijst met drempelinstellingen (Threshold Settings List). Klik op Opslaan (Save) om op te slaan. Als u een item wilt verwijderen, selecteert u het in de Lijst met tintcurve-instellingen (Tone Curve Settings List) of de Lijst met drempelinstellingen (Threshold Settings List) en klikt u op Verwijderen (Delete).
Dialoogvenster Voorkeuren Klik op Voorkeuren... (Preferences...) in het scherm van ScanGear (scannerstuurprogramma) om het dialoogvenster Voorkeuren (Preferences) te openen. In het dialoogvenster Voorkeuren (Preferences) kunt u geavanceerde instellingen voor de functies van ScanGear opgeven via de tabbladen Scanner, Voorbeeld (Preview), Scannen (Scan) en Kleurinstellingen (Color Settings). Tabblad Scanner Hiermee kunt u de stille modus en een map opgeven waarin de afbeeldingen tijdelijk worden opgeslagen.
Tabblad Scanner Op het tabblad Scanner kunt u de volgende instellingen opgeven. • Stille instellingen (Quiet Settings) Met de stille functie kunt u ervoor zorgen dat het apparaat minder geluid maakt. Gebruik deze functie als u het geluidsniveau van het apparaat wilt beperken, bijvoorbeeld wanneer u 's nachts scant of afdrukt. Klik op Instellingen... (Settings...) om de stille modus in te stellen.
• Stille modus gebruiken op opgegeven tijden (Use quiet mode during specified hours) Selecteer deze optie als u wilt dat het apparaat minder geluid maakt op de opgegeven tijden. Geef de Begintijd (Start time) en de Eindtijd (End time) op van de periode waarin de stille modus actief moet zijn. Belangrijk U moet voor Begintijd (Start time) en Eindtijd (End time) verschillende tijden opgeven.
Tabblad Voorbeeld Op het tabblad Voorbeeld (Preview) kunt u de volgende instellingen opgeven. • Voorbeeld bij starten van ScanGear (Preview at Start of ScanGear) Selecteer wat u wilt doen met Voorbeeld wanneer ScanGear (scannerstuurprogramma) wordt gestart. • Voorbeeld automatisch uitvoeren (Automatically Execute Preview) ScanGear begint automatisch met een voorbeeldweergave bij het opstarten.
• Groter (Larger) Hiermee wordt 105% (in breedte en hoogte) weergegeven van het gedeelte dat voor het standaardformaat wordt weergegeven. • Standaard (Standard) Het standaardformaat. • Kleiner (Smaller) Hiermee wordt 95% (in breedte en hoogte) weergegeven van het gedeelte dat wordt weergegeven voor het standaardformaat. Opmerking Als u de instelling Uitsnijdformaat voor filmminiatuur (Cropping Size for Thumbnail View) wijzigt, worden de voorbeeldafbeeldingen vernieuwd en bijgesneden tot het nieuwe formaat.
Tabblad Scannen Op het tabblad Scannen (Scan) kunt u de volgende instellingen opgeven. • Status van het dialoogvenster ScanGear na het scannen (Status of ScanGear dialog after scanning) Selecteer wat u wilt doen met ScanGear (scannerstuurprogramma) nadat afbeeldingen zijn gescand. • ScanGear automatisch sluiten (Close ScanGear automatically) Selecteer deze optie wanneer u na het scannen wilt teruggaan naar de oorspronkelijke toepassing.
Uitvoer op achterzijde/voorzijde (snel) (Output by back/front(Fast)) is ingesteld voor het scannen naar toepassingen, zoals OCR-software, die niet het scherm ScanGear openen. • Uitvoer op achterzijde/voorzijde (snel) (Output by back/front(Fast)) Deze instelling wordt aanbevolen als u snel moet scannen. De documenten worden snel uitgevoerd. De documenten worden echter niet in de juiste paginavolgorde uitgevoerd.
Tabblad Kleurinstellingen Op het tabblad Kleurinstellingen (Color Settings) kunt u de volgende instellingen opgeven. • Kleuraanpassing Selecteer een van de volgende opties. U kunt een instelling selecteren wanneer Kleurenmodus (Color Mode) is ingesteld op Kleur (Color) of Grijswaarden (Grayscale). • Aanbevolen (Recommended) Gebruik deze optie om een levendige reproductie van de tint van een document weer te geven op het scherm. Deze instelling wordt aanbevolen.
niet overeenkomt met de standaardwaarde in ScanGear en de kleuren van de oorspronkelijke afbeelding niet goed worden weergegeven op de monitor. Klik op Standaard (Defaults) om de gammawaarde terug te zetten op de standaardwaarde (1,80). Opmerking Raadpleeg de handleiding van uw monitor voor de gammawaarde. Neem contact op met de fabrikant als de gammawaarde niet in de handleiding staat vermeld.
Items plaatsen (wanneer u scant vanaf een computer) Informatie over hoe u items moet plaatsen op de plaat of ADF (automatische documentinvoer) van uw scanner of printer. Plaats de items op de juiste manier op de plaat, afhankelijk van het type item dat u wilt scannen. Anders worden de items mogelijk niet goed gescand. Belangrijk Leg geen voorwerpen op de documentklep. Wanneer u de documentklep opent, kunnen er voorwerpen in uw scanner of printer vallen, wat leidt tot slecht functioneren.
van de plaat kunnen worden geplaatst, worden mogelijk opgeslagen als PDF-bestanden. Als u bestanden in een andere indeling dan PDF wilt opslaan, geeft u bij het scannen de gegevensindeling op. Meerdere items plaatsen Houd een ruimte van 1 cm (0,4 inch) of meer vrij tussen de randen (schuin gestreept gebied) van de glasplaat en de items, en tussen de items. Delen die op het diagonaal gestreepte gebied zijn geplaatst kunnen niet worden gescand.
Plaats de documenten met de bedrukte zijde omhoog totdat u een piepgeluid hoort. Plaats de documenten met de bedrukte zijde omhoog als u beide zijden van de documenten wilt scannen.
Bijsnijdkaders aanpassen (ScanGear) Met bijsnijden selecteert u het gebied in een afbeelding dat u wilt behouden en verwijdert u de rest tijdens het scannen. Op het tabblad Basismodus (Basic Mode) en Geavanceerde modus (Advanced Mode) kunt u bijsnijdkaders (scangebieden) opgeven voor de afbeelding(en) die in het voorbeeldgebied van het scherm wordt/worden weergegeven. Als u een scan uitvoert, wordt elk gebied dat door middel van het bijsnijdkader is opgegeven als aparte afbeelding gescand.
Een bijsnijdkader aanpassen De cursor verandert in (pijl) wanneer deze boven een bijsnijdkader wordt geplaatst. Als u nu op de muisknop klikt en de muisaanwijzer in de richting van de pijl sleept, wordt het bijsnijdkader dienovereenkomstig vergroot of verkleind. De cursor verandert in (vierrichtingspijl) wanneer deze binnen een bijsnijdkader wordt geplaatst. Klik op de muisknop en sleep de muis om het hele bijsnijdkader te verplaatsen.
U kunt meerdere bijsnijdkaders maken en op elk daarvan verschillende scaninstellingen toepassen. U kunt ook meerdere bijsnijdkaders selecteren door op de afzonderlijke kaders te klikken terwijl u de Command-toets ingedrukt houdt. Als u meerdere bijsnijdkaders selecteert en de instellingen op het tabblad aan de rechterkant van ScanGear wijzigt, worden deze instellingen op alle geselecteerde bijsnijdkaders toegepast.
Algemene opmerkingen (scannerstuurprogramma) ScanGear (scannerstuurprogramma) kent de volgende beperkingen. Denk hieraan wanneer u het programma gebruikt. Beperkingen van het scannerstuurprogramma • Als de computer door meerdere gebruikers wordt gebruikt of u zich na het afmelden opnieuw aanmeldt, kan een bericht verschijnen dat ScanGear in gebruik is. In dat geval haalt u de USB-kabel uit de computer en sluit u deze weer aan.
ScanGear (scannerstuurprogramma) bijwerken De nieuwste versie van ScanGear (scannerstuurprogramma) verkrijgen De onnodige versie van ScanGear (scannerstuurprogramma) verwijderen Voordat u ScanGear (scannerstuurprogramma) installeert ScanGear (scannerstuurprogramma) installeren
De nieuwste versie van ScanGear (scannerstuurprogramma) verkrijgen Als u een upgrade uitvoert van de huidige versie van ScanGear (scannerstuurprogramma) naar de nieuwste versie van ScanGear, kunt u eventuele problemen die u ondervindt, mogelijk oplossen. De versie van ScanGear controleren Start ScanGear en klik op (Informatie) om de versie van ScanGear weer te geven. ScanGear ophalen U kunt ScanGear verkrijgen door naar onze website te gaan en de ScanGear-versie voor uw model te downloaden.
De onnodige versie van ScanGear (scannerstuurprogramma) verwijderen U kunt ScanGear (scannerstuurprogramma) verwijderen als u het niet meer gebruikt. Voordat u ScanGear verwijdert, sluit u alle actieve toepassingen en koppelt u de USB-kabel los waarmee het apparaat op de computer is aangesloten. 1. Verwijder ScanGear. Selecteer Computer in het menu Ga (Go) van de Finder.
Voordat u ScanGear (scannerstuurprogramma) installeert Controleer de volgende punten voordat u ScanGear (scannerstuurprogramma) installeert. Controleer deze ook als u ScanGear niet kunt installeren. Apparaatstatus • Als het apparaat en de computer met een USB-kabel zijn verbonden, koppelt u deze USB-kabel los van de computer. • Schakel het apparaat uit. Computerinstellingen • Sluit alle actieve toepassingen. • Meld u aan als beheerder van de computer.
ScanGear (scannerstuurprogramma) installeren Ga naar onze website op internet en download de nieuwste versie van ScanGear (scannerstuurprogramma). Volg deze stappen om de gedownloade versie van ScanGear te installeren. 1. Activeer de schijf. Dubbelklik op het gedownloade schijfbestand. Het bestand wordt uitgepakt en de schijf wordt geactiveerd. 2. Start het installatieprogramma. Dubbelklik op het .pkg-bestand op de uitgepakte schijf. De installatie wordt gestart. 3. Installeer het stuurprogramma.
Handige informatie over scannen Bijsnijdkaders aanpassen (IJ Scan Utility) Resolutie Gegevensindelingen Kleurafstemming
Bijsnijdkaders aanpassen (IJ Scan Utility) Met bijsnijden selecteert u het gebied in een afbeelding dat u wilt behouden en verwijdert u de rest tijdens het scannen. In het venster Afbeelding samenvoegen (Image Stitch) kunt u een bijsnijdkader opgeven voor de afbeelding die in het voorbeeldgebied wordt weergegeven.
Resolutie De gegevens in de door u gescande afbeelding zijn een verzameling puntjes die informatie over helderheid en kleur bevatten. De dichtheid van deze puntjes wordt 'resolutie' genoemd. De resolutie bepaalt hoeveel details de afbeelding bevat. De resolutie wordt uitgedrukt in het aantal puntjes per inch (dpi). Dpi is het aantal puntjes per inch (2,5 cm). Hoe hoger de resolutie (waarde), des te gedetailleerder de afbeelding. Hoe lager de resolutie (waarde), des te minder details in de afbeelding.
Opmerking Wanneer u de gescande afbeelding groter wilt afdrukken, scan dan met een hogere resolutie dan hierboven wordt aangeraden.
Gegevensindelingen Bij het opslaan van gescande afbeeldingen kunt u een gegevensindeling kiezen. Geef de meest geschikte gegevensindeling op, in overeenstemming met het gebruik van de afbeelding in een bepaalde toepassing. De beschikbare gegevensindelingen zijn afhankelijk van de toepassing en het besturingssysteem (Windows of Mac OS). Zie hieronder voor de eigenschappen van iedere gegevensindeling voor afbeeldingen. PNG (standaardbestandsextensie: .
Kleurafstemming Kleurafstemming' is het aanbrengen van aanpassingen zodat de kleurtonen van het originele item, het monitorscherm en de kleurenafdruk met elkaar overeenkomen. Op uw scanner of printer worden de kleurtinten aangepast zoals hieronder wordt aangegeven.
Items plaatsen (wanneer u scant vanaf een computer) Informatie over hoe u items moet plaatsen op de plaat of ADF (automatische documentinvoer) van uw scanner of printer. Plaats de items op de juiste manier op de plaat, afhankelijk van het type item dat u wilt scannen. Anders worden de items mogelijk niet goed gescand. Belangrijk Leg geen voorwerpen op de documentklep. Wanneer u de documentklep opent, kunnen er voorwerpen in uw scanner of printer vallen, wat leidt tot slecht functioneren.
van de plaat kunnen worden geplaatst, worden mogelijk opgeslagen als PDF-bestanden. Als u bestanden in een andere indeling dan PDF wilt opslaan, geeft u bij het scannen de gegevensindeling op. Meerdere items plaatsen Houd een ruimte van 1 cm (0,4 inch) of meer vrij tussen de randen (schuin gestreept gebied) van de glasplaat en de items, en tussen de items. Delen die op het diagonaal gestreepte gebied zijn geplaatst kunnen niet worden gescand.
Plaats de documenten met de bedrukte zijde omhoog totdat u een piepgeluid hoort. Plaats de documenten met de bedrukte zijde omhoog als u beide zijden van de documenten wilt scannen.
Scannen via het bedieningspaneel van het apparaat Gescande gegevens naar de computer sturen met het bedieningspaneel van het apparaat Basis Items instellen met het bedieningspaneel van het apparaat Opgeven hoe gereageerd moet worden op opdrachten van het bedieningspaneel met gebruik van IJ Scan Utility
Gescande gegevens naar de computer sturen met het bedieningspaneel van het apparaat U kunt de gescande gegevens naar de computer sturen vanaf het bedieningspaneel van het apparaat. Controleer het volgende voordat u gescande gegevens naar de computer verstuurt: • ScanGear (scannerstuurprogramma) is geïnstalleerd. Als ScanGear (scannerstuurprogramma) nog niet is geïnstalleerd, plaatst u de installatie-cd-rom in het schijfstation van de computer en installeert u ScanGear (scannerstuurprogramma).
Belangrijk Plaats originelen op de juiste manier, in overeenstemming met het type. Als u dit niet doet, is het mogelijk dat bepaalde originelen niet goed worden gescand. Meer informatie over het plaatsen van het origineel: Originelen plaatsen De volgende items kunnen worden gescand. Foto's, briefkaarten, visitekaartjes, tijdschriften, kranten, tekstdocumenten en BD's/cd's/dvd's. De volgende items kunnen niet goed worden gescand.
• Als u een andere instelling dan JPEG of TIFF selecteert voor Gegevensindeling (Data format), begint het apparaat met scannen en worden de gescande gegevens doorgestuurd naar de computer. • Als u PDF of Compacte PDF (Compact PDF) selecteert bij Gegevensindeling (Data format), wordt een bevestigingsscherm weergegeven waarin wordt gevraagd of u wilt doorgaan met scannen nadat het scannen is voltooid. Selecteer Ja (Yes) en druk op de knop OK om de originelen continue te scannen.
Items instellen met het bedieningspaneel van het apparaat U kunt de scaninstellingen, zoals scanformaat, resolutie of gegevensindeling, wijzigen. Selecteer een instelling met de knoppen en druk vervolgens op de knop OK. om een instellingsitem aan te passen en druk op de knop OK. Het volgende Gebruik de knop instellingsitem wordt weergegeven. Opmerking Een * (sterretje) op het LCD geeft de huidige instelling aan.
Opgeven hoe gereageerd moet worden op opdrachten van het bedieningspaneel met gebruik van IJ Scan Utility Met IJ Scan Utility kunt u opgeven hoe moet worden gereageerd als er wordt gescand vanaf het bedieningspaneel. Opmerking De schermen voor het opgeven van de reacties bij het uitvoeren van Automatisch scannen vanaf het bedieningspaneel worden in de volgende beschrijvingen als voorbeeld gebruikt. 1. Start IJ Scan Utility. IJ Scan Utility starten 2. Klik op Instellingen (Settings...).
Dialoogvenster Instellingen (Opslaan naar pc (foto)) Dialoogvenster Instellingen (Opslaan naar pc (document)) 4. Geef afbeeldingscorrecties op in Scanopties (Scan Options). 5. Geef de bestandsnaam en andere instellingen op in Instellingen opslaan (Save Settings). 6. Selecteer de toepassing die u na het scannen wilt starten in Instellingen voor de toepassing (Application Settings).
7. Klik op OK. De reacties worden volgens de opgegeven instellingen uitgevoerd wanneer u start met scannen vanaf het bedieningspaneel.