MX720 series Podręcznik online Skanowanie polski (Polish)
Skanowanie Skanowanie z komputera Skanowanie za pomocą programu IJ Scan Utility Skanowanie za pomocą używanej aplikacji (ScanGear) Przydatne informacje na temat skanowania Ekran menu i ustawień programu IJ Network Scanner Selector EX Umieszczanie przedmiotów (w przypadku skanowania z komputera) Skanowanie z panelu operacyjnego urządzenia Przekazywanie zeskanowanych danych do komputera za pomocą panelu operatora urządzenia Podstawy Dołączanie zeskanowanych danych do wiadomości e-mail za pomocą panelu operacy
Skanowanie z komputera Skanowanie za pomocą programu IJ Scan Utility Skanowanie za pomocą używanej aplikacji (ScanGear) Przydatne informacje na temat skanowania Ekran menu i ustawień programu IJ Network Scanner Selector EX Umieszczanie przedmiotów (w przypadku skanowania z komputera) 3
Skanowanie z panelu operacyjnego urządzenia Przekazywanie zeskanowanych danych do komputera za pomocą panelu operatora urządzenia Podstawy Dołączanie zeskanowanych danych do wiadomości e-mail za pomocą panelu operacyjnego urządzenia Zapisywanie zeskanowanych danych w napędzie flash USB przy użyciu panelu operacyjnego urządzenia Usuwanie zeskanowanych danych zapisanych w napędzie flash USB Wprowadzanie ustawień pozycji menu za pomocą panelu operacyjnego urządzenia Ustawienia skanowania sieciowego Wybieranie
Skanowanie za pomocą programu IJ Scan Utility Co to jest program IJ Scan Utility (oprogramowanie skanera)? Uruchamianie programu IJ Scan Utility Łatwe skanowanie z funkcją Automatyczne skanowanie Podstawy Skanowanie fotografii Skanowanie dokumentów Skanowanie z ulubionymi ustawieniami Skanowanie przedmiotów większych niż płyta szklana (Złączenie obrazu) Skanowanie wielu przedmiotów naraz Skanowanie wielu dokumentów naraz za pomocą ADF (Automatycznego podajnika dokumentów) Skanowanie każdego dokumentu z ob
Co to jest program IJ Scan Utility (oprogramowanie skanera)? IJ Scan Utility jest aplikacją, która umożliwia łatwe skanowanie fotografii, dokumentów itd. Wszystkie czynności od skanowania po zapisywanie można wykonywać, klikając po prostu odpowiednią ikonę na ekranie głównym programu IJ Scan Utility. Co można zrobić za pomocą programu IJ Scan Utility Łatwe skanowanie odpowiednio do przeznaczenia Można skanować, klikając po prostu jedną z ikon — na przykład Automat.
Ważne Niektóre funkcje są dostępne tylko po zainstalowaniu oprogramowania My Image Garden. Uwaga Informacje na temat wskazywania programu, z którym ma nastąpić integracja, można znaleźć w części „Okno dialogowe Ustawienia”.
Uruchamianie programu IJ Scan Utility Uwaga Jeśli masz więcej niż jeden skaner lub w używanym egzemplarzu rodzaj połączenia został zmieniony z USB na połączenie sieciowe, skonfiguruj środowisko sieciowe za pomocą programu IJ Scan Utility. Ustawienia skanowania sieciowego W menu Idź (Go) programu Finder wybierz opcję Aplikacje (Applications), a następnie po kolei kliknij dwukrotnie folder Canon Utilities, folder IJ Scan Utility i ikonę Canon IJ Scan Utility, aby uruchomić program IJ Scan Utility.
Łatwe skanowanie z funkcją Automatyczne skanowanie Skanowanie jest łatwiejsze dzięki automatycznemu wykrywaniu typu elementu. Ważne Poniższe rodzaje przedmiotów mogą być skanowane nieprawidłowo. W takim przypadku dopasuj ramki przycinania (obszary skanowania) w widoku całego obrazu, uruchom program ScanGear (sterownik skanera) i ponownie zeskanuj dokument. Fotografie o białawym tle Obrazy lub dokumenty wydrukowane na białym papierze, rękopisy, wizytówki itp.
Skanowanie fotografii Fotografie umieszczone na płycie szklanej można skanować z odpowiednimi dla nich ustawieniami. 1. Umieść fotografię na płycie. Umieszczanie przedmiotów (w przypadku skanowania z komputera) 2. Uruchom program IJ Scan Utility. Uruchamianie programu IJ Scan Utility 3. Kliknij przycisk Ustawienia (Settings...), wybierz okno dialogowe Ustawienia (Skanowanie fotografii) (Settings (Photo Scan)), a następnie wprowadź odpowiednie ustawienia rozmiaru papieru, rozdzielczości itd.
Skanowanie dokumentów Dokumenty umieszczone na płycie szklanej można skanować z odpowiednimi dla nich ustawieniami. 1. Umieść element na płycie szklanej. Umieszczanie przedmiotów (w przypadku skanowania z komputera) 2. Uruchom program IJ Scan Utility. Uruchamianie programu IJ Scan Utility 3. Kliknij przycisk Ustawienia (Settings...), wybierz okno dialogowe Ustawienia (Skanowania dokumentu) (Settings (Document Scan)), a następnie wprowadź odpowiednie ustawienia rozmiaru papieru, rozdzielczości itd.
Skanowanie z ulubionymi ustawieniami Przedmioty umieszczone na płycie szklanej można skanować z zapisanymi wcześniej ulubionymi ustawieniami. Jest to wygodny sposób na zapisywanie często używanych ustawień lub na wprowadzanie szczegółowych ustawień skanowania. 1. Uruchom program IJ Scan Utility. Uruchamianie programu IJ Scan Utility 2. Kliknij przycisk Ustawienia (Settings...
Skanowanie przedmiotów większych niż płyta szklana (Złączenie obrazu) W tym oknie można zeskanować osobno lewą i prawą połowę przedmiotu większego od płyty szklanej, a następnie połączyć zeskanowane obrazy w jedną całość. Można skanować przedmioty, które są nawet dwukrotnie większe od płyty szklanej. Uwaga Poniżej objaśniono, jak należy skanować przedmiot umieszczony po lewej stronie. 1. Uruchom program IJ Scan Utility. Uruchamianie programu IJ Scan Utility 2. Kliknij przycisk Ustawienia (Settings...
5. Upewnij się, że w obszarze Kierunek skanowania (Scan Direction) wybrane jest ustawienie Skanuj od lewej (Scan from Left). 6. Przedmiot, którego obraz ma zostać wyświetlony po lewej stronie ekranu, umieść na płycie szklanej stroną do zeskanowania skierowaną do dołu. 7. Kliknij przycisk Rozpocznij skanowanie obrazu 1 (Start Scanning Image 1). Zostanie zeskanowany pierwszy przedmiot, a jego obraz pojawi się w obszarze 1. Uwaga Aby anulować skanowanie, kliknij przycisk Anuluj (Cancel).
8. Przedmiot, którego obraz ma zostać wyświetlony po prawej stronie ekranu, umieść na płycie szklanej stroną do zeskanowania skierowaną do dołu. 9. Kliknij przycisk Rozpocznij skanowanie obrazu 2 (Start Scanning Image 2). Zostanie zeskanowany drugi przedmiot, a jego obraz pojawi się w obszarze 2. Uwaga Aby anulować skanowanie, kliknij przycisk Anuluj (Cancel). 10. W razie potrzeby dopasuj zeskanowane obrazy.
Zaznacz pole wyboru Dopasuj ramki przycinania (Adjust cropping frames), aby wskazać obszar do zapisania. Dopasowywanie ramek przycinania (program IJ Scan Utility) Aby ponownie zeskanować dany przedmiot, wybierz jego obraz w obszarze Podgląd lub jego (Usuń). Wybrany obraz zostanie miniaturę na górze ekranu, a następnie kliknij przycisk usunięty, co umożliwi ponowne zeskanowanie przedmiotu. 11. Kliknij przycisk Zapisz (Save). Zostanie zapisany obraz połączony.
Skanowanie wielu przedmiotów naraz Można zeskanować jednocześnie dwie lub większą liczbę fotografii (małych przedmiotów) umieszczonych na płycie szklanej i zapisać każdy obraz oddzielnie. Ważne Poniższe rodzaje przedmiotów mogą być przycinane nieprawidłowo. W takim przypadku dopasuj ramki przycinania (obszary skanowania) w widoku całego obrazu, uruchom program ScanGear (sterownik skanera) i ponownie zeskanuj dokument.
5. Wybierz ustawienie Wybierz źródło (Select Source) odpowiednie dla skanowanych przedmiotów. 6. Wybierz dla opcji Rozmiar papieru (Paper Size) ustawienie Automatyczne skanowanie (Auto scan), a następnie kliknij przycisk OK.
Pojawi się ekran główny programu IJ Scan Utility. Uwaga Szczegółowe informacje o elementach ustawień znajdujących się w oknie dialogowym Ustawienia można znaleźć na poniższych stronach. Okno dialogowe Ustawienia (Skanowanie fotografii) Okno dialogowe Ustawienia (Skanowania dokumentu) Okno dialogowe Ustawienia (Skanowanie niestandardowe) 7. Kliknij przycisk Niestandard. (Custom). Następuje jednoczesne skanowanie wielu przedmiotów. Uwaga Aby anulować skanowanie, kliknij przycisk Anuluj (Cancel).
Skanowanie wielu dokumentów naraz za pomocą ADF (Automatycznego podajnika dokumentów) W ADF (Automatyczny podajnik dokumentów) można umieścić wiele dokumentów i zeskanować je naraz. W tej sekcji opisano sposób skanowania jednej strony wielu dokumentów naraz. Informacje na temat automatycznego skanowania obu stron dokumentów można znaleźć w części Skanowanie każdego dokumentu z obu stron naraz.
ustawienia opcji Orientacja (Orientation) i Strona szycia (Binding Side). Sposób umieszczania dokumentów podczas skanowania tylnych stron zależy od ustawienia opcji Strona szycia (Binding Side). Po wprowadzeniu ustawień kliknij przycisk OK. Pojawi się ekran główny programu IJ Scan Utility. Uwaga Szczegółowe informacje o elementach ustawień znajdujących się w oknie dialogowym Ustawienia można znaleźć na poniższych stronach.
Kliknij przycisk Ustaw. orient. skanowania dokum... (Document Scan Orientation Settings...), aby określić orientację skanowanych dokumentów. W wyświetlonym oknie dialogowym możesz wybrać ustawienia opcji Orientacja (Orientation) i Strona szycia (Binding Side). Sposób umieszczania dokumentów podczas skanowania tylnych stron zależy od ustawienia opcji Strona szycia (Binding Side). Kliknij przycisk Ustawienie wydruku dokumentu... (Document Output Setting...
Zapisywanie po sprawdzeniu wyników skanowania Można sprawdzić wyniki skanowania, a następnie zapisać obrazy na komputerze. Ważne W przypadku skanowania z użyciem funkcji Automat. (Auto) lub panelu operacyjnego nie można sprawdzać wyników skanowania przed ich zapisaniem. Uwaga W poniższych przykładach posłużono się ekranami skanowania fotografii. 1. Uruchom program IJ Scan Utility. Uruchamianie programu IJ Scan Utility 2. Kliknij przycisk Ustawienia (Settings...). Pojawi się okno dialogowe Ustawienia.
Pojawi się ekran główny programu IJ Scan Utility. Uwaga Szczegółowe informacje o elementach ustawień znajdujących się w oknie dialogowym Ustawienia można znaleźć na poniższych stronach. Okno dialogowe Ustawienia (Skanowanie fotografii) Okno dialogowe Ustawienia (Skanowania dokumentu) Okno dialogowe Ustawienia (Skanowanie niestandardowe) Okno dialogowe Ustawienia (Skanuj i złącz) Okno dialogowe Ustawienia (ScanGear) 5. Kliknij przycisk Fotografia (Photo). Rozpocznie się skanowanie.
Zeskanowane obrazy są zapisywane zgodnie z ustawieniami.
Wysyłanie zeskanowanych obrazów pocztą e-mail Zeskanowane obrazy można wysyłać pocztą e-mail. Uwaga W poniższych przykładach posłużono się ekranami skanowania fotografii. 1. Uruchom program IJ Scan Utility. Uruchamianie programu IJ Scan Utility 2. Kliknij przycisk Ustawienia (Settings...). Pojawi się okno dialogowe Ustawienia. Okno dialogowe Ustawienia 3. Kliknij przycisk Skanowanie fotografii (Photo Scan). 4.
Uwaga Klienty poczty e-mail na potrzeby obsługi załączników można dodawać w menu rozwijanym. Po wybraniu ustawienia Brak (dołącz ręcznie) (None (Attach Manually)) należy ręcznie dołączyć zeskanowane i zapisane obrazy do wiadomości e-mail. 5. Kliknij przycisk OK. Pojawi się ekran główny programu IJ Scan Utility. Uwaga Szczegółowe informacje o elementach ustawień znajdujących się w oknie dialogowym Ustawienia można znaleźć na poniższych stronach.
Okno dialogowe Ustawienia (Automatyczne skanowanie) Okno dialogowe Ustawienia (Skanowanie fotografii) Okno dialogowe Ustawienia (Skanowania dokumentu) Okno dialogowe Ustawienia (Skanowanie niestandardowe) Okno dialogowe Ustawienia (ScanGear) 6. Kliknij przycisk Fotografia (Photo). Rozpocznie się skanowanie. Po zakończeniu skanowania zostanie uruchomiony wybrany klient poczty e-mail, a obrazy zostaną dołączone do nowej wiadomości. Uwaga Aby anulować skanowanie, kliknij przycisk Anuluj (Cancel).
Wyodrębnianie tekstu z zeskanowanych obrazów (OCR) Służy do skanowania tekstu w zeskanowanych czasopismach i gazetach oraz wyświetlania go w programie TextEdit (dostarczanym z komputerami z systemem operacyjnym Mac OS). Uwaga Tekst można wyodrębniać podczas skanowania za pośrednictwem opcji Dokument (Document) lub Niestandard. (Custom) albo programu ScanGear. W poniższych przykładach posłużono się ekranami skanowania dokumentów. 1. Uruchom program IJ Scan Utility. Uruchamianie programu IJ Scan Utility 2.
Uwaga W przypadku wybrania opcji My Image Garden po zakończeniu skanowania tekst na obrazie zostanie wyodrębniony i wyświetlony w programie TextEdit (dostarczanym z komputerami z systemem operacyjnym Mac OS). 5. Kliknij przycisk OK. Pojawi się ekran główny programu IJ Scan Utility. Uwaga Szczegółowe informacje o elementach ustawień znajdujących się w oknie dialogowym Ustawienia można znaleźć na poniższych stronach.
Okno dialogowe Ustawienia (Skanowania dokumentu) Okno dialogowe Ustawienia (Skanowanie niestandardowe) Okno dialogowe Ustawienia (ScanGear) 6. Kliknij przycisk Dokument (Document). Rozpocznie się skanowanie. Po zakończeniu skanowania zeskanowane obrazy są zapisywane zgodnie z ustawieniami, a wyodrębniony tekst pojawia się w wybranej aplikacji. Uwaga Aby anulować skanowanie, kliknij przycisk Anuluj (Cancel).
Ekrany programu IJ Scan Utility Ekran główny programu IJ Scan Utility Okno dialogowe Ustawienia Okno dialogowe Ustawienia (Automatyczne skanowanie) Okno dialogowe Ustawienia (Skanowanie fotografii) Okno dialogowe Ustawienia (Skanowania dokumentu) Okno dialogowe Ustawienia (Skanowanie niestandardowe) Okno dialogowe Ustawienia (Skanuj i złącz) Okno dialogowe Ustawienia (ScanGear) Okno dialogowe Ustawienia (Zapisz na komputerze (automatycznie)) Okno dialogowe Ustawienia (Zapisz na komputerze (fotografia)) Okno
Ekran główny programu IJ Scan Utility W menu Idź (Go) programu Finder wybierz opcję Aplikacje (Applications), a następnie po kolei kliknij dwukrotnie folder Canon Utilities, folder IJ Scan Utility i ikonę Canon IJ Scan Utility, aby uruchomić program IJ Scan Utility. Wszystkie czynności od skanowania po zapisywanie można wykonać, klikając odpowiednią ikonę. • Nazwa produktu (Product Name) Podaje nazwę produktu, do którego obsługi skonfigurowano program IJ Scan Utility.
Otwiera niniejszy podręcznik. • Ustawienia (Settings...) Powoduje wyświetlenie okna dialogowego Ustawienia, w którym można wprowadzić ustawienia skanowania/zapisu i określić sposób działania programu po zakończeniu skanowania.
Okno dialogowe Ustawienia W oknie dialogowym Ustawienia znajdują się trzy karty: (Skanowanie z komputera), (Skanowanie przy użyciu panelu operacyjnego) i (Ustawienia ogólne). Po kliknięciu danej karty zmienia się widok w czerwonej ramce i można wprowadzać zaawansowane ustawienia funkcji dostępnych na każdej karcie. Karta (Skanowanie z komputera) Umożliwia określenie sposobu reagowania na polecenia w przypadku skanowania za pomocą programu IJ Scan Utility lub My Image Garden.
W przypadku korzystania ze skanera lub drukarki za pośrednictwem połączenia sieciowego nie pojawia się okno dialogowe Ustawienia (Zapisz na komputerze (automatycznie)) (Settings (Save to PC (Auto))). Karta (Ustawienia ogólne) Umożliwia wybór używanego produktu, ograniczenie rozmiaru plików wysyłanych w załącznikach do wiadomości e-mail, wybór języka, w jakim mają być wykrywane napisy na obrazach, oraz wskazanie folderu, w którym obrazy będą zapisywane tymczasowo.
Okno dialogowe Ustawienia (Automatyczne skanowanie) Aby wyświetlić okno dialogowe Ustawienia (Automatyczne skanowanie) (Settings (Auto Scan)), kliknij na karcie (Skanowanie z komputera) przycisk Automatyczne skanowanie (Auto Scan). W oknie dialogowym Ustawienia (Automatyczne skanowanie) (Settings (Auto Scan)) można wprowadzać zaawansowane ustawienia skanowania w celu skanowania z automatycznym wykrywaniem rodzaju przedmiotu.
W przypadku skanowania dwóch lub więcej dokumentów za pośrednictwem podajnika ADF, należy umieszczać w nim dokumenty tego samego rozmiaru.
Okno dialogowe Ustawienia (Skanowanie fotografii) Aby wyświetlić okno dialogowe Ustawienia (Skanowanie fotografii) (Settings (Photo Scan)), kliknij na karcie (Skanowanie z komputera) przycisk Skanowanie fotografii (Photo Scan). W oknie dialogowym Ustawienia (Skanowanie fotografii) (Settings (Photo Scan)) można wprowadzać zaawansowane ustawienia skanowania dotyczące takich przedmiotów, jak fotografie.
Uwaga Kliknij przycisk Domyślne (Defaults), aby przywrócić wartości domyślne określonym ustawieniom. • Rozdzielczość (Resolution) Służy do określania rozdzielczości skanowanego przedmiotu. Im wyższa rozdzielczość (wartość), tym więcej szczegółów na obrazie. Rozdzielczość • Kompresuj zeskanowane obrazy po ich przeslaniu do komputera (Compress scanned images upon transfer) Umożliwia zastosowanie kompresji zeskanowanych obrazów podczas ich przesyłania do komputera.
• Sprawdź wyniki skanowania (Check scan results) Powoduje wyświetlenie po skanowaniu okna dialogowego Zapisz ustawienia (Save Settings). Okno dialogowe Zapisz ustawienia Ważne Jeśli okno dialogowe Ustawienia zostanie wyświetlone z poziomu programu My Image Garden, opcja ta nie pojawia się. (3) Obszar Ustawienia aplikacji • Otwórz za pomocą aplikacji (Open with an application) Zaznacz to pole wyboru, jeśli chcesz uwydatnić lub poprawić zeskanowane obrazy. Aplikację można wskazać w menu rozwijanym.
Okno dialogowe Ustawienia (Skanowania dokumentu) Aby wyświetlić okno dialogowe Ustawienia (Skanowania dokumentu) (Settings (Document Scan)), kliknij na karcie (Skanowanie z komputera) przycisk Skanowania dokumentu (Document Scan). W oknie dialogowym Ustawienia (Skanowania dokumentu) (Settings (Document Scan)) można wprowadzać zaawansowane ustawienia skanowania dotyczące takich przedmiotów, jak dokumenty.
Jeśli wybrane jest ustawienie Dokument (ADF/płyta szklana) (Document (ADF/Platen)), a dokumenty są umieszczone zarówno na płycie szklanej, jak i w podajniku ADF, zeskanowane zostaną te z podajnika ADF. • Tryb koloru (Color Mode) Umożliwia wybór trybu koloru, w jakim zostanie zeskanowany dany przedmiot. Ważne Aby wybrać opcję Czarno-biały (Black and White), usuń zaznaczenie pola wyboru Kompresuj zeskanowane obrazy po ich przeslaniu do komputera (Compress scanned images upon transfer).
(Scan both sides when scanning from the ADF) oraz po wybraniu trybu Dokument (automat. druk dwustronny z ADF) (Document (ADF Auto Duplex)). Kliknij go, aby wyświetlić okno dialogowe Ustawienie wydruku dokumentu (Document Output Setting), w którym możesz określić sposób wyprowadzania papieru z podajnika ADF podczas skanowania. Do wyboru są ustawienia: Wydruk odwrócony przód/tył (szybki) (Output with front and back reversed (Fast)) i Wydruk posortowany (Output in the page order).
• Redukuj cień marginesu (Reduce gutter shadow)/Redukuj cień marginesu (płyta szklana) (Reduce gutter shadow (platen)) Powoduje redukowanie cienia na marginesie, który pojawia się między stronami przy skanowaniu otwartych broszur. Ważne Ta funkcja jest dostępna tylko w przypadku skanowania z płyty szklanej. Opcja dostępna, tylko gdy nie jest zaznaczone pole wyboru Kompresuj zeskanowane obrazy po ich przeslaniu do komputera (Compress scanned images upon transfer).
Wybór formatu danych, w którym będą zapisywane zeskanowane obrazy. Do wyboru są ustawienia JPEG/Exif, TIFF, PNG, PDF i PDF (wielostronnic.) (PDF (Multiple Pages)). Ważne Nie można wybrać ustawienia JPEG/Exif, jeśli dla opcji Tryb koloru (Color Mode) wybrane jest ustawienie Czarno-biały (Black and White). Jeśli w obszarze Ustawienia aplikacji (Application Settings) wybrano opcję Rozpocznij OCR (Start OCR), nie można wybrać ustawienia PDF ani PDF (wielostronnic.) (PDF (Multiple Pages)).
Wskaż aplikację lub folder w oknie dialogowym wyświetlanym po wybraniu w menu rozwijanym polecenia Dodaj... (Add...). • Instrukcje (Instructions) Otwiera niniejszy podręcznik. • Domyślne (Defaults) Umożliwia przywrócenie wartości domyślnych ustawieniom znajdującym się na wyświetlonym ekranie.
Okno dialogowe Ustawienia (Skanowanie niestandardowe) Aby wyświetlić okno dialogowe Ustawienia (Skanowanie niestandardowe) (Settings (Custom Scan)), kliknij na karcie (Skanowanie z komputera) przycisk Skanowanie niestandardowe (Custom Scan). W oknie dialogowym Ustawienia (Skanowanie niestandardowe) (Settings (Custom Scan)) można wprowadzać zaawansowane ustawienia skanowania zgodnie z własnymi preferencjami.
Nadruki na cienkim, białym papierze Długie, wąskie przedmioty, np. zdjęcia panoramiczne Odblaskowe etykiety dysków mogą nie zostać zeskanowane zgodnie z oczekiwaniami. Sposób umieszczenia przedmiotu, który ma zostać zeskanowany, musi być odpowiednio dobrany do jego rodzaju. W przeciwnym razie przedmioty mogą zostać zeskanowane nieprawidłowo. Szczegółowe informacje na temat umieszczania przedmiotów można znaleźć w części „Umieszczanie przedmiotów (w przypadku skanowania z komputera)”.
Przycisk ten pojawia się po wybraniu dla opcji Wybierz źródło (Select Source) ustawienia ADF lub Automatyczny (Auto). Kliknij go, aby wyświetlić okno dialogowe Ustaw. orient. skanowania dokumentu (Document Scan Orientation Settings), w którym można określić orientację i stronę szycia dokumentów skanowanych za pośrednictwem podajnika ADF. Ważne Jeśli skanowana jest tylko przednia strona każdego dokumentu, nie można wprowadzać ustawienia opcji Strona szycia (Binding Side). • Ustawienie wydruku dokumentu...
Powoduje automatyczne wprowadzanie odpowiednich korekt w zależności od rodzaju przedmiotu. Ważne W wyniku korekt odcień koloru może się zmienić w stosunku do odcienia na obrazie źródłowym. W takim przypadku należy usunąć zaznaczenie tego pola wyboru i wykonać skanowanie. Uwaga Włączenie tej funkcji powoduje wydłużenie czasu skanowania.
Uwaga W celu skorygowania cienia na marginesie podczas skanowania przedmiotów o niestandardowych rozmiarach lub przy skanowaniu określonych obszarów należy skorzystać z karty Tryb zaawansowany (Advanced Mode) w programie ScanGear (sterowniku skanera). Szczegółowe informacje na ten temat można znaleźć w części „Korekcja cienia marginesu” dotyczącej użytkowanego modelu, na stronie głównej dokumentu Podręcznik online.
Nie można wybrać ustawienia JPEG/Exif, jeśli dla opcji Tryb koloru (Color Mode) wybrane jest ustawienie Czarno-biały (Black and White). Jeśli w obszarze Ustawienia aplikacji (Application Settings) wybrano opcję Rozpocznij OCR (Start OCR), nie można wybrać ustawienia PDF, PDF (wielostronnic.) (PDF (Multiple Pages)) ani Automatycznie (Auto). Uwaga Opcja Automatyczny (Auto) pojawia się, tylko gdy dla opcji Wybierz źródło (Select Source) wybrano ustawienie Automat. (Auto) • Ustawienia (Settings...
Uwaga Wskaż aplikację lub folder w oknie dialogowym wyświetlanym po wybraniu w menu rozwijanym polecenia Dodaj... (Add...). • Instrukcje (Instructions) Otwiera niniejszy podręcznik. • Domyślne (Defaults) Umożliwia przywrócenie wartości domyślnych ustawieniom znajdującym się na wyświetlonym ekranie.
Okno dialogowe Ustawienia (Skanuj i złącz) Aby wyświetlić okno dialogowe Ustawienia (Skanuj i złącz) (Settings (Scan and Stitch)), kliknij na karcie (Skanowanie z komputera) przycisk Skanuj i złącz (Scan and Stitch). W oknie dialogowym Ustawienia (Skanuj i złącz) (Settings (Scan and Stitch)) można wprowadzać zaawansowane ustawienia skanowania przedmiotów większych od płyty szklanej.
Kliknij przycisk (Strzałka w prawo), aby wprowadzić poniższe ustawienia. Dostępne elementy ustawień zmieniają się w zależności od ustawienia opcji Wybierz źródło (Select Source). Ważne Gdy dla opcji Tryb koloru (Color Mode) wybrane jest ustawienie Czarno-biały (Black and White), opcja Ustawienia przetwarzania obrazu (Image Processing Settings) jest niedostępna.
Okno dialogowe Zapisz ustawienia Ważne Jeśli okno dialogowe Ustawienia zostanie wyświetlone z poziomu programu My Image Garden, opcja ta nie pojawia się. (3) Obszar Ustawienia aplikacji • Otwórz za pomocą aplikacji (Open with an application) Zaznacz to pole wyboru, jeśli chcesz uwydatnić lub poprawić zeskanowane obrazy. Aplikację można wskazać w menu rozwijanym.
Okno dialogowe Ustawienia (ScanGear) Aby wyświetlić okno dialogowe Ustawienia (ScanGear) (Settings (ScanGear)), kliknij na karcie (Skanowanie z komputera) przycisk ScanGear. W oknie dialogowym Ustawienia (ScanGear) (Settings (ScanGear)) można określić sposób zapisu obrazów podczas skanowania przedmiotów za pomocą programu ScanGear (sterownika skanera) oraz jego działanie po ich zapisaniu.
słów kluczowych i ich typ kompresji oraz format danych, w jakim mają być zapisywane obrazy zeskanowane z użyciem trybu Automatyczne skanowanie. Okno dialogowe Ustawienia formatu danych • Zapisz w (Save in) Powoduje wyświetlenie folderu, w którym zapisywane są zeskanowane obrazy. W celu zmiany folderu wskaż folder docelowy w oknie dialogowym wyświetlanym po wybraniu w menu rozwijanym polecenia Dodaj... (Add...). Domyślny folder zapisu to Dokumenty (Documents).
Uwaga Wskaż aplikację lub folder w oknie dialogowym wyświetlanym po wybraniu w menu rozwijanym polecenia Dodaj... (Add...). • Instrukcje (Instructions) Otwiera niniejszy podręcznik. • Domyślne (Defaults) Umożliwia przywrócenie wartości domyślnych ustawieniom znajdującym się na wyświetlonym ekranie.
Okno dialogowe Ustawienia (Zapisz na komputerze (automatycznie)) Aby wyświetlić okno dialogowe Ustawienia (Zapisz na komputerze (automatycznie)) (Settings (Save to PC (Auto))), kliknij na karcie (Skanowanie przy użyciu panelu operacyjnego) przycisk Zapisz na komputerze (automatycznie) (Save to PC (Auto)).
(2) Obszar Zapisz ustawienia • Nazwa pliku (File Name) Wprowadź nazwę pliku, w którym ma zostać zapisany obraz. Przy zapisywaniu pliku do jego podanej nazwy dodawany jest przyrostek w postaci daty i 4 cyfr o formacie „_20XX0101_0001”. • Format danych (Data Format) Wybrano ustawienie Automatycznie (Auto). Przy zapisywaniu stosowane są automatycznie poniższe formaty danych w zależności od rodzaju przedmiotu.
Okno dialogowe Ustawienia (Zapisz na komputerze (fotografia)) Aby wyświetlić okno dialogowe Ustawienia (Zapisz na komputerze (fotografia)) (Settings (Save to PC (Photo))), kliknij na karcie (Skanowanie przy użyciu panelu operacyjnego) przycisk Zapisz na komputerze (fotografia) (Save to PC (Photo)).
Kliknięcie powoduje wyświetlenie okna dialogowego Ustawienia formatu danych (Data Format Settings), w którym można określić jakość zapisywanych obrazów, wyszukiwanie plików PDF według słów kluczowych oraz format danych, w jakim mają być zapisywane obrazy zeskanowane z użyciem trybu Automatyczne skanowanie. Okno dialogowe Ustawienia formatu danych • Zapisz w (Save in) Powoduje wyświetlenie folderu, w którym zapisywane są zeskanowane obrazy.
Okno dialogowe Ustawienia (Zapisz na komputerze (dokument)) Aby wyświetlić okno dialogowe Ustawienia (Zapisz na komputerze (dokument)) (Settings (Save to PC (Document))), kliknij na karcie (Skanowanie przy użyciu panelu operacyjnego) przycisk Zapisz na komputerze (dokument) (Save to PC (Document)).
W wyniku korekt odcień koloru może się zmienić w stosunku do odcienia na obrazie źródłowym. W takim przypadku należy usunąć zaznaczenie tego pola wyboru i wykonać skanowanie. Uwaga Włączenie tej funkcji powoduje wydłużenie czasu skanowania. • Redukuj cień marginesu (płyta szklana) (Reduce gutter shadow (platen)) Powoduje redukowanie cienia na marginesie, który pojawia się między stronami przy skanowaniu otwartych broszur. Ważne Ta funkcja jest dostępna tylko w przypadku skanowania z płyty szklanej.
słów kluczowych oraz format danych, w jakim mają być zapisywane obrazy zeskanowane z użyciem trybu Automatyczne skanowanie. Okno dialogowe Ustawienia formatu danych • Zapisz w (Save in) Powoduje wyświetlenie folderu, w którym zapisywane są zeskanowane obrazy. W celu zmiany folderu wskaż folder docelowy w oknie dialogowym wyświetlanym po wybraniu w menu rozwijanym polecenia Dodaj... (Add...). Domyślny folder zapisu to Dokumenty (Documents).
Okno dialogowe Ustawienia (Dołącz do wiadomości e-mail (fotografia)) Aby wyświetlić okno dialogowe Ustawienia (Dołącz do wiadomości e-mail (fotografia)) (Settings (Attach to E-mail (Photo))), kliknij na karcie (Skanowanie przy użyciu panelu operacyjnego) przycisk Dołącz do wiadomości e-mail (fotografia) (Attach to E-mail (Photo)).
• Ustawienia (Settings...) Kliknięcie powoduje wyświetlenie okna dialogowego Ustawienia formatu danych (Data Format Settings), w którym można określić jakość zapisywanych obrazów, wyszukiwanie plików PDF według słów kluczowych oraz format danych, w jakim mają być zapisywane obrazy zeskanowane z użyciem trybu Automatyczne skanowanie. Okno dialogowe Ustawienia formatu danych • Zapisz w (Save in) Powoduje wyświetlenie folderu, w którym zapisywane są zeskanowane obrazy.
Okno dialogowe Ustawienia (Dołącz do wiadomości e-mail (dokument)) Aby wyświetlić okno dialogowe Ustawienia (Dołącz do wiadomości e-mail (dokument)) (Settings (Attach to E-mail (Document))), kliknij na karcie (Skanowanie przy użyciu panelu operacyjnego) przycisk Dołącz do wiadomości e-mail (dokument) (Attach to E-mail (Document)).
Opcja dostępna, tylko gdy nie jest zaznaczone pole wyboru Kompresuj zeskanowane obrazy po ich przeslaniu do komputera (Compress scanned images upon transfer). W wyniku korekt odcień koloru może się zmienić w stosunku do odcienia na obrazie źródłowym. W takim przypadku należy usunąć zaznaczenie tego pola wyboru i wykonać skanowanie. Uwaga Włączenie tej funkcji powoduje wydłużenie czasu skanowania.
Kliknięcie powoduje wyświetlenie okna dialogowego Ustawienia formatu danych (Data Format Settings), w którym można określić jakość zapisywanych obrazów, wyszukiwanie plików PDF według słów kluczowych oraz format danych, w jakim mają być zapisywane obrazy zeskanowane z użyciem trybu Automatyczne skanowanie. Okno dialogowe Ustawienia formatu danych • Zapisz w (Save in) Powoduje wyświetlenie folderu, w którym zapisywane są zeskanowane obrazy. W celu zmiany folderu kliknij przycisk Dodaj... (Add...
Okno dialogowe Ustawienia (Ustawienia ogólne) Aby wyświetlić okno dialogowe Ustawienia (Ustawienia ogólne) (Settings (General Settings)), kliknij kartę (Ustawienia ogólne). W oknie dialogowym Ustawienia (Ustawienia ogólne) (Settings (General Settings)) można wybrać użytkowany produkt, ograniczyć rozmiar plików wysyłanych w załącznikach do wiadomości e-mail, wybrać język, w jakim mają być wykrywane napisy na obrazach, oraz wskazać folder, w którym obrazy będą zapisywane tymczasowo.
• Instrukcje (Instructions) Otwiera niniejszy podręcznik. • Domyślne (Defaults) Umożliwia przywrócenie wartości domyślnych ustawieniom znajdującym się na wyświetlonym ekranie.
Okno dialogowe Ustawienia formatu danych Okno dialogowe Ustawienia formatu danych (Data Format Settings) można wyświetlić w jeden z poniższych sposobów. • Kliknij przycisk Ustawienia... (Settings...) w obszarze Zapisz ustawienia (Save Settings) na każdej karcie okna dialogowego Ustawienia. • Kliknij przycisk Ustawienia... (Settings...
• Format dla elementu wykrytego jako fotografia w Automatycznym Skanowaniu (Format for Item Detected as Photo in Auto Scan) Umożliwia wybór formatu danych dla zapisywanych automatycznie elementów wykrytych w trybie Automatyczne skanowanie jako fotografie. • Domyślne (Defaults) Umożliwia przywrócenie wartości domyślnych ustawieniom znajdującym się na wyświetlonym ekranie.
Okno dialogowe Zapisz ustawienia Aby po skanowaniu pojawiało się okno dialogowe Zapisz ustawienia (Save Settings), w oknie dialogowym Ustawienia zaznacz w obszarze Zapisz ustawienia (Save Settings) pole wyboru Sprawdź wyniki skanowania (Check scan results). Format danych i miejsce docelowe można określić podczas przeglądania miniatur wyników skanowania. Ważne Po skanowaniu za pomocą programu My Image Garden lub panelu operacyjnego okno dialogowe Zapisz ustawienia (Save Settings) nie jest wyświetlane.
• Format danych (Data Format) Wybór formatu danych, w którym będą zapisywane zeskanowane obrazy. Do wyboru są ustawienia JPEG/Exif, TIFF, PNG, PDF i PDF (wielostronnic.) (PDF (Multiple Pages)). Ważne W poniższych przypadkach nie można wybrać ustawienia PDF ani PDF (wielostronnic.) (PDF (Multiple Pages)).
Okno Złączenie obrazu Aby wyświetlić okno Złączenie obrazu (Image Stitch), na ekranie głównym programu IJ Scan Utility kliknij przycisk Złącz (Stitch). W oknie tym można zeskanować osobno lewą i prawą połowę przedmiotu większego od płyty szklanej, a następnie połączyć zeskanowane obrazy w jedną całość. Można skanować przedmioty, które są nawet dwukrotnie większe od płyty szklanej.
• Skanuj obraz 1 (Scan Image 1) • Rozpocznij skanowanie obrazu 1 (Start Scanning Image 1) Umożliwia zeskanowanie pierwszego przedmiotu. • Skanuj obraz 2 (Scan Image 2) • Rozpocznij skanowanie obrazu 2 (Start Scanning Image 2) Umożliwia zeskanowanie drugiego przedmiotu. • Dopasuj ramki przycinania (Adjust cropping frames) Obszar skanowania można dopasowywać na podglądzie.
Umożliwia zapisanie dwóch zeskanowanych obrazów jako jednego. • Anuluj (Cancel) Umożliwia anulowanie skanowania w trybie Złącz (Stitch). (2) Pasek narzędzi • Pasek narzędzi Umożliwia usuwanie zeskanowanych obrazów oraz dostosowywanie obrazów wyświetlanych w obszarze podglądu. • (Usuń) Powoduje usunięcie zeskanowanego obrazu. • (Powiększ/zmniejsz) Umożliwia powiększanie i pomniejszanie obrazu wyświetlanego w obszarze podglądu.
• Po zeskanowaniu pierwszego przedmiotu zainicjowanym przez kliknięcie przycisku Rozpocznij skanowanie obrazu 1 (Start Scanning Image 1) Obraz jest skanowany w kierunku określonym za pomocą opcji Kierunek skanowania (Scan Direction), a obok niego pojawia się symbol 2. • Po zeskanowaniu drugiego przedmiotu zainicjowanym przez kliknięcie przycisku Rozpocznij skanowanie obrazu 2 (Start Scanning Image 2) Pojawiają się dwa zeskanowane obrazy.
Skanowanie za pomocą używanej aplikacji (ScanGear) Co to jest program ScanGear (sterownik skanera)? Skanowanie z ustawieniami zaawansowanymi przy użyciu programu ScanGear (sterownik skanera) Uruchamianie programu ScanGear (sterownik skanera) Skanowanie w trybie podstawowym Skanowanie w trybie zaawansowanym Skanowanie wielu dokumentów za pomocą automatycznego podajnika dokumentów (ADF) w trybie zaawansowanym Skanowanie wielu dokumentów jednocześnie przy użyciu programu ScanGear (sterownika skanera) Poprawian
Co to jest program ScanGear (sterownik skanera)? Program ScanGear (sterownik skanera) to oprogramowanie wymagane do skanowania dokumentów. Pozwala ono określić rozmiar wydruku skanowanego dokumentu i korygować obraz podczas skanowania. Program ScanGear można uruchomić z poziomu aplikacji My Image Garden lub IJ Scan Utility. Można go również uruchomić za pomocą innych aplikacji zgodnych ze standardowym interfejsem TWAIN. (Program ScanGear jest sterownikiem zgodnym z interfejsem TWAIN).
Aby skanować czasopisma zawierające wiele kolorowych fotografii, wybierz opcję Czasopismo (kolor) (Magazine (Color)). W przypadku modelu wyposażonego w podajnik ADF z automatycznym drukowaniem dwustronnym można określić sposób wyprowadzania papieru z podajnika ADF podczas skanowania obustronnego. Służy do tego opcja Ustawienia wydruku dwustronnego z podajnika ADF (ADF Duplex Paper Output Settings) na karcie Skanuj (Scan) w oknie dialogowym Preferencje (Preferences). Karta Skanuj 3.
8. Kliknij przycisk Skanuj (Scan). Rozpocznie się skanowanie. Uwaga Kliknij przycisk (Informacje), aby otworzyć okno dialogowe, w którym można sprawdzić bieżące ustawienia skanowania (typ dokumentu itp.). Sposób działania programu ScanGear po zakończeniu skanowania można określić przy użyciu ustawienia Stan okna dialogowego programu ScanGear po zakończeniu skanowania (Status of ScanGear dialog after scanning) na karcie Skanuj (Scan) okna dialogowego Preferencje (Preferences).
Skanowanie w trybie zaawansowanym Karta Tryb zaawansowany (Advanced Mode) służy do określania trybu koloru, rozdzielczości wydruku, jasności obrazu, odcienia koloru itp. podczas skanowania. Opis sposobu skanowania wielu dokumentów jednocześnie można znaleźć w temacie „Skanowanie wielu dokumentów jednocześnie przy użyciu programu ScanGear (sterownika skanera)”.
Zmniejszanie efektu prześwitywania w dokumentach tekstowych lub rozjaśnianie koloru podstawowego w przypadku papieru z makulatury, gazet itp. przy skanowaniu dokumentów Wybierz dla opcji Zmniejszanie efektu prześwitywania (Reduce Show-through) ustawienie WŁ (ON). WYŁ (OFF) WŁ (ON) Wyostrzanie lekko nieostrych obrazów Dla ustawienia Wyostrz obraz (Unsharp Mask) wybierz opcję WŁ (ON). WYŁ (OFF) WŁ (ON) Zmniejszanie gradacji i wzorów paskowych Dla ustawienia Derasteryzacja (Descreen) wybierz opcję WŁ (ON).
Brak (None) Średnia (Medium) Poprawianie zdjęć, które wyblakły z powodu upływu czasu lub uległy przebarwieniom W zależności od stopnia, w jakim kolory wyblakły lub uległy przebarwieniom, ustaw opcję Korekcja zaniku (Fading Correction) na wartość Niska (Low), Średnia (Medium) lub Wysoka (High). Brak (None) Średnia (Medium) Zmniejszanie ziarnistości W zależności od stopnia ziarnistości, ustaw opcję Korekcja ziarna (Grain Correction) na wartość Niska (Low), Średnia (Medium) lub Wysoka (High).
Dopasowywanie kolorów przy użyciu desenia kolorów Za pomocą funkcji deseniu kolorów, dostępnej na karcie Tryb podstawowy (Basic Mode) programu ScanGear (sterownika skanera), można wyświetlać podgląd zmian koloru i uzyskiwać naturalne kolory. Dopasowywanie kolorów Kolory, które wyblakły z powodu upływu czasu lub uległy przebarwieniom, można poprawić. „Przebarwienie” to zjawisko, w którym z powodu panujących warunków atmosferycznych lub obecności silnych kolorów pewien kolor dominuje na całym zdjęciu.
Poniżej znajduje się przykład poprawienia niebieskiego obrazu. Ponieważ nasycenie kolorów Niebieski (Blue) i Zielony (Green) jest zbyt duże, kliknij strzałki kolorów Żółty (Yellow) i Amarantowy (Magenta), aby dokonać poprawek. Przed Po Uwaga Korekty kolorów są wprowadzane tylko w ramkach przycinania (obszarach skanowania) lub w ramce wybranej w widoku miniatur. Wiele klatek lub ramek przycinania można wybrać, klikając je przy wciśniętym klawiszu Command.
Dopasowywanie nasycenia i balansu koloru Na karcie Tryb zaawansowany (Advanced Mode) programu ScanGear (sterownika skanera) kliknij przycisk (Nasycenie/Balans kolorów). Uwaga Kliknij przycisk Domyślne (Defaults), aby przywrócić wartości domyślne wszystkich ustawień w bieżącym oknie. Nasycenie Umożliwia dopasowanie nasycenia obrazu (żywości kolorów). Można rozjaśnić kolory, które wyblakły z upływem czasu itd.
Są to pary dopełniających się kolorów (po połączeniu każdej pary otrzymywany jest odcień szarości). Można uzyskiwać naturalne kolory ujęcia, zmniejszając nasycenie koloru dominującego i zwiększając nasycenie koloru dopełniającego. Zazwyczaj trudno jest całkowicie poprawić obraz, dopasowując tylko jedną parę kolorów. Należy znaleźć część obrazu, która powinna być biała, i dopasować wszystkie kolory w taki sposób, aby stała się ona biała. Można również wprowadzić wartość liczbową (od -127 do 127).
Dopasowywanie jasności i kontrastu Na karcie Tryb zaawansowany (Advanced Mode) programu ScanGear (sterownika skanera) kliknij przycisk (Jasność/Kontrast). Uwaga Kliknij przycisk (strzałka w dół), aby przełączyć do widoku szczegółowego. Kliknij przycisk (strzałka w górę), aby powrócić do poprzedniego widoku. Kliknij przycisk Domyślne (Defaults), aby przywrócić wartości domyślne wszystkich ustawień w bieżącym oknie.
Jasność w obszarze Jasność (Brightness) w lewo, aby przyciemnić Dopasuj jasność obrazu. Przesuń suwak obraz, lub w prawo, aby go rozjaśnić. Można również wprowadzić wartość liczbową (od -127 do 127). Przyciemniony Oryginalny obraz Rozjaśniony Uwaga Jeśli obraz zostanie zbyt mocno rozjaśniony, może zostać utracone podświetlenie, a jeśli zostanie zbyt mocno przyciemniony, może zostać utracony cień. Kontrast „Kontrast” to stopień różnicy między jaśniejszymi i ciemniejszymi częściami obrazu.
Dopasowywanie histogramu Na karcie Tryb zaawansowany (Advanced Mode) programu ScanGear (sterownika skanera) kliknij przycisk (Histogram). Uwaga Kliknij przycisk Domyślne (Defaults), aby przywrócić wartości domyślne wszystkich ustawień w bieżącym oknie. Kanał (Channel) Każdy punkt obrazu jest połączeniem koloru czerwonego, zielonego i niebieskiego w różnych proporcjach (gradacjach). Te kolory można osobno dopasować jako „kanały”.
Więcej danych znajduje się w zakresie podświetlenia. Więcej danych znajduje się w zakresie cienia. Dane są rozłożone w obu zakresach, podświetlenia i cienia. Dopasowywanie histogramów (przy użyciu suwaka) Wybierz ustawienie Kanał (Channel), a następnie przesuń suwak aby określić poziom cienia lub podświetlenia. (Punkt czerni) lub (Punkt bieli), - Wszystkie elementy po lewej stronie suwaka (Punkt czerni) będą czarne (poziom 0).
Obrazy, na których więcej danych znajduje się w zakresie podświetlenia Przesuń suwak Punkt pośredni w stronę zakresu podświetlenia. Obrazy, na których więcej danych znajduje się w zakresie cienia Przesuń suwak Punkt pośredni w stronę zakresu cienia. Dopasowywanie histogramów (przy użyciu przycisków) Po wybraniu ustawienia Kanał (Channel) i kliknięciu przycisku Punkt czerni, Punkt pośredni lub Punkt bieli wskaźnik myszy na obrazie podglądu przyjmuje kształt pipety.
Dopasowywanie krzywej tonowej Na karcie Tryb zaawansowany (Advanced Mode) programu ScanGear (sterownika skanera) kliknij przycisk (Ustawienia krzywej tonowej). Uwaga Kliknij przycisk Domyślne (Defaults), aby przywrócić wartości domyślne wszystkich ustawień w bieżącym oknie. Kanał (Channel) Każdy punkt obrazu jest połączeniem koloru czerwonego, zielonego i niebieskiego w różnych proporcjach (gradacjach). Te kolory można osobno dopasować jako „kanały”.
Dopasowywanie krzywej tonowej Z listy Wybierz krzywą tonową (Select Tone Curve) wybierz krzywą tonową spośród następujących opcji: Bez korekcji (No correction), Prześwietlenie (Overexposure), Niedoświetlenie (Underexposure), Wysoki kontrast (High contrast), Odwróć negatyw/pozytyw (Reverse the negative/positive image) i Edycja krzywej niestandard (Edit custom curve).
Edycja krzywej niestandard (Edit custom curve) Można przeciągać wybrane punkty Krzywej tonowej, aby swobodnie dopasować jasność odpowiednich obszarów.
Ustawianie progu Jasność obrazów kolorowych i obrazów w odcieniach szarości jest wyrażana jako wartość z przedziału od 0 do 255, natomiast przy tworzeniu obrazów czarno-białych wszystkim kolorom są przyporządkowywane wyłącznie kolory czarny (0) lub biały (255). „Próg” to wartość graniczna określająca kolor jako czarny lub biały. Ustawiając odpowiednio poziom progowy, można wyostrzyć tekst w dokumencie oraz zredukować prześwit wydruku w przypadku gazet.
Ekrany programu ScanGear (sterownik skanera) Karta Tryb podstawowy Karta Tryb zaawansowany Ustawienia wejściowe Ustawienia wydruku Ustawienia obrazu Przyciski dopasowywania kolorów Okno dialogowe Preferencje Karta Skaner Karta Podgląd Karta Skanuj Karta Ustawienia koloru 121
Karta Tryb podstawowy Ten tryb umożliwia łatwe skanowanie przez wykonywanie czynności przedstawianych na ekranie. W tej sekcji opisano ustawienia i funkcje dostępne na karcie Tryb podstawowy (Basic Mode). Podczas skanowania za pomocą ADF (Automatyczny podajnik dokumentów) dokumenty są skanowane bez podglądu. (1) Przyciski ustawień i operacji (2) Pasek narzędzi (3) Obszar podglądu Uwaga Wyświetlane elementy zależą od typu dokumentu i widoku.
Służy do dwustronnego skanowania dokumentów z ADF w trybie czarno-białym. Dokumenty są skanowane w formacie zszywanym wzdłuż długiego boku, przy czym krawędzią górną jest krawędź trafiająca do podajnika ADF jako pierwsza. Ważne Niektóre aplikacje nie obsługują skanowania ciągłego za pomocą ADF. Szczegółowych informacji należy szukać w podręczniku danej aplikacji. Uwaga Funkcja wyostrzania obrazu będzie aktywna po wybraniu typu dokumentu.
W widoku miniatur Aby wyświetlić ramkę przycinania, należy przeciągnąć kursor po miniaturze. Jeśli ramka przycinania jest wyświetlana, zostanie zeskanowany fragment obrazu ograniczony ramką. Jeśli nie jest wyświetlana ramka przycinania, każda klatka jest skanowana osobno. W widoku całego obrazu Jeśli ramka przycinania nie jest wyświetlana, skanowany będzie cały obszar podglądu. Jeśli ramka przycinania jest wyświetlana, zostanie zeskanowany fragment obrazu ograniczony ramką. • Rozmiar papieru (L, A4 itd.
Więcej informacji na temat obecności i sposobu wyświetlania ramki przycinania na obrazie podglądu można znaleźć w punkcie Ramka przycinania na obrazach podglądu (Cropping Frame on Previewed Images) w temacie „Karta Podgląd” (okno dialogowe Preferencje (Preferences)). • Odwróć współczynnik proporcji (Invert aspect ratio) Dostępny, gdy dla opcji Rozmiar wydruku (Output Size) wybrane jest ustawienie inne niż Elastyczny (Flexible). Kliknięcie tego przycisku powoduje obrót ramki przycinania.
Uwaga Po rozpoczęciu skanowania będą wyświetlane informacje o postępie operacji. Aby anulować skanowanie, należy kliknąć przycisk Anuluj (Cancel). • Preferencje... (Preferences...) Powoduje otwarcie okna dialogowego Preferencje (Preferences), w którym można wprowadzać zaawansowane ustawienia skanowania/podglądu. Okno dialogowe Preferencje • Zamknij (Close) Umożliwia zamknięcie programu ScanGear (sterownik skanera). (2) Pasek narzędzi • Pasek narzędzi Umożliwia dopasowywanie i obracanie obrazów podglądu.
Umożliwia wybór obrazów w widoku miniatur. Zostaną one otoczone niebieską obwódką. • (Wybierz wszystkie ramki przycinania) Dostępny, gdy zostały wyznaczone co najmniej dwie ramki przycinania. Powoduje zmianę ramek przycinania w grube linie przerywane i zastosowanie ustawień do nich wszystkich. • (Usuń ramkę przycinania) Usuwa zaznaczoną ramkę przycinania. • (Informacje) Powoduje wyświetlenie informacji o wersji programu ScanGear oraz bieżących ustawieniach skanowania (typ dokumentu itd.).
Jeśli na pasku narzędzi jest wyświetlany przycisk (Cały obraz) Elementy na płycie szklanej są skanowane i wyświetlane jako jeden obraz. Zostaną zeskanowane wszystkie części w ramkach przycinania. Uwaga Na wyświetlanym obrazie można wyznaczyć ramkę przycinania. W widoku miniatur można utworzyć tylko jedną ramkę przycinania dla każdego obrazu. W widoku całego obrazu można utworzyć wiele ramek przycinania.
Karta Tryb zaawansowany Ten tryb umożliwia wprowadzanie zaawansowanych ustawień skanowania, np. trybu koloru, rozdzielczości wyjściowej, jasności obrazu czy odcienia koloru. W tej sekcji opisano ustawienia i funkcje dostępne na karcie Tryb zaawansowany (Advanced Mode). Podczas skanowania za pomocą ADF (Automatyczny podajnik dokumentów) dokumenty są skanowane bez podglądu. (1) Przyciski ustawień i operacji (2) Pasek narzędzi (3) Obszar podglądu Uwaga Wyświetlane elementy zależą od typu dokumentu i widoku.
Wprowadź nazwę w polu Nazwa ustawienia (Setting Name) i kliknij przycisk Dodaj (Add). Nazwa ta pojawi się w polu Lista ustawień ulubionych (Favorite Settings List). Po kliknięciu przycisku Zapisz (Save) nazwa pojawi się na liście Ustawienia ulubione (Favorite Settings) i będzie można ją wybrać podobnie jak elementy wstępnie zdefiniowane. Aby usunąć element, należy zaznaczyć go w polu Lista ustawień ulubionych (Favorite Settings List), a następnie kliknąć przycisk Usuń (Delete).
• Skanuj (Scan) Umożliwa rozpoczęcie skanowania. Uwaga Po rozpoczęciu skanowania będą wyświetlane informacje o postępie operacji. Aby anulować skanowanie, należy kliknąć przycisk Anuluj (Cancel). Po zakończeniu skanowania może pojawić się okno dialogowe z monitem o wybranie następnej czynności. Aby zakończyć, należy wykonać instrukcje wyświetlane w tym monicie.
W widoku całego obrazu • (Miniatura) / (Cały obraz) Umożliwia przełączenie widoku w obszarze podglądu. Obszar podglądu • (Wyczyść) Powoduje usunięcie podglądu z obszaru podglądu. Przycisk ten resetuje też ustawienia paska narzędzi i dopasowywania kolorów. • (Przytnij) Umożliwia określenie obszaru skanowania przez przeciągnięcie kursora myszy.
Powoduje zmianę ramek przycinania w grube linie przerywane i zastosowanie ustawień do nich wszystkich. • (Usuń ramkę przycinania) Usuwa zaznaczoną ramkę przycinania. • (Informacje) Powoduje wyświetlenie informacji o wersji programu ScanGear oraz bieżących ustawieniach skanowania (typ dokumentu itd.). • (Otwórz przewodnik) Umożliwia wyświetlenie niniejszej strony. (3) Obszar podglądu • Obszar podglądu W obszarze podglądu wyświetlane są próbne obrazy uzyskane po kliknięciu przycisku Podgląd (Preview).
Uwaga Na wyświetlanym obrazie można wyznaczyć ramkę przycinania. W widoku miniatur można utworzyć tylko jedną ramkę przycinania dla każdego obrazu. W widoku całego obrazu można utworzyć wiele ramek przycinania.
Ustawienia wejściowe Sekcja Ustawienia wejściowe (Input Settings) umożliwia skonfigurowanie następujących elementów: • Wybierz źródło (Select Source) Wyświetlany jest typ dokumentu, który ma być skanowany. Aby skanować z użyciem płyty szklanej, wybierz ustawienie Płyta szklana (Platen).
• Orientacja oryginału (Original Orientation) Służy do ustawiania orientacji i zszywanego boku dokumentów skanowanych z ADF. Kliknij przycisk Ustawienia... (Settings...), aby wyświetlić okno dialogowe Orientacja (Orientation). Ważne Okno dialogowe Orientacja (Orientation) może się pojawić, tylko gdy dla opcji Wybierz źródło (Select Source) wybrano ustawienie Dokument (Druk jednostronny z podajnika ADF) (Document (ADF Simplex)) lub Dokument (Druk dwustronny z podajnika ADF) (Document (ADF Duplex)).
Wprowadzane wartości muszą należeć do wybranego zakresu rozmiaru dokumentu. Jeśli ustawienie Rozdzielczość wyjściowa (Output Resolution) ma wartość 600 dpi, rozmiar minimalny wynosi 96 pikseli x 96 pikseli przy skali 100%. W przypadku autoprzycinania w widoku całego obrazu nie jest zachowywany współczynnik proporcji, ponieważ priorytet ma rozmiar. Szczegółowe informacje na temat ramek przycinania można znaleźć w części „Dopasowywanie ramek przycinania (program ScanGear)”.
Ustawienia wydruku Sekcja Ustawienia wydruku (Output Settings) umożliwia skonfigurowanie następujących elementów: • Rozdzielczość wyjściowa (Output Resolution) Wybór rozdzielczości, z jaką będzie przeprowadzane skanowanie. Im wyższa rozdzielczość (wartość), tym więcej szczegółów na obrazie. Rozdzielczość należy wybrać spośród opcji wyświetlanych po kliknięciu przycisku; wartość można też wprowadzić (w krokach co 1 dpi).
W widoku całego obrazu Jeśli ramka przycinania nie jest wyświetlana, skanowany będzie cały obszar podglądu. Jeśli ramka przycinania jest wyświetlana, zostanie zeskanowany fragment obrazu ograniczony ramką. Uwaga Aby powiększyć lub pomniejszyć zeskanowany obraz, należy wprowadzić odpowiednie wartości w polach (Szerokość) i (Wysokość) w obszarze Ustawienia wydruku (Output Settings) lub określić wartość (z dokładnością do 1%) w polu %.
Szczegółowe informacje na temat ramek przycinania można znaleźć w części „Dopasowywanie ramek przycinania (program ScanGear)”. Więcej informacji na temat obecności i sposobu wyświetlania ramki przycinania na obrazie podglądu można znaleźć w punkcie Ramka przycinania na obrazach podglądu (Cropping Frame on Previewed Images) w temacie „Karta Podgląd” (okno dialogowe Preferencje (Preferences)).
Ustawienia obrazu Ważne Nie należy stosować tych funkcji w przypadku obrazów bez efektu mory, kurzu/rys lub wyblakłych kolorów. Może to mieć niekorzystny wpływ na odcień koloru. Efekty korekcji obrazu mogą nie być uwidocznione w podglądzie. Uwaga Dostępne ustawienia zależą od konfiguracji trybu Tryb koloru (Color Mode). Włączenie opcji Ustawienia obrazu (Image Settings) może powodować wydłużenie czasu skanowania.
Uwaga Jeśli obraz nie jest poprawnie dopasowywany przy ustawieniu Automatyczne (Auto), należy określić typ dokumentu. W wyniku dopasowania obrazu ton koloru może się zmienić w stosunku do tonu w obrazie źródłowym. W takim przypadku dla ustawienia Dopasowywanie obrazu (Image Adjustment) należy określić wartość Brak (None).
• Wysoka (High) Wybranie tej opcji umożliwia wyeliminowanie większych cząstek kurzu oraz rys. Proces ten może jednak pozostawić widoczne ślady lub mogą zostać usunięte delikatne fragmenty obrazu. Ważne Ta funkcja może nie działać w przypadku niektórych typów fotografii. Uwaga W przypadku skanowania materiałów drukowanych zaleca się wybranie ustawienia Brak (None).
Tej opcji należy użyć, gdy przy ustawieniu średnim efekt jest zbyt silny. • Średnia (Medium) To ustawienie jest zalecane w zwykłych warunkach. • Wysoka (High) Tej opcji należy użyć, gdy przy ustawieniu średnim efekt jest zbyt słaby. Ważne Na płycie szklanej nie można umieszczać przedmiotów o wadze przekraczającej 2,0 kg (4,4 funta). Nie należy także naciskać dokumentów z siłą przekraczającą 2,0 kg (4,4 funta). Silne dociskanie może spowodować nieprawidłową pracę skanera lub pęknięcie płyty szklanej.
Przyciski dopasowywania kolorów Przyciski dopasowywania kolorów służą do precyzyjnego korygowania jasności i odcieni kolorów na obrazie. Można regulować m.in. jasność i kontrast całego obrazu, wprowadzać korekty dla najjaśniejszych i najciemniejszych partii obrazu (histogram) oraz ustawiać balans przy użyciu krzywej tonowej.
Umożliwia dopasowanie jasności obrazu przez wybranie typu wykresu (krzywej tonowej) pokazującego balans tonów wejściowych i wyjściowych. Można precyzyjnie dopasować jasność wybranego obszaru. Dopasowywanie krzywej tonowej • (Przegląd końcowy) Służy do końcowego sprawdzenia dopasowania kolorów. Wyświetlony zostanie połączony widok krzywej tonowej i histogramu uzyskany na podstawie dalszych operacji przetwarzania obrazu. Na tym ekranie nie ma żadnych ustawień, które można zmieniać.
(Delete). Kliknięcie przycisku Zapisz (Save) powoduje zapisanie ustawień wyświetlanych w polu Lista ustawień krzywej tonowej (Tone Curve Settings List) lub Lista ustawień progu (Threshold Settings List). Można też załadować zapisane ustawienia krzywej tonowej/wartości progowej i zastosować je do obrazu podglądu. Aby załadować te ustawienia, wybierz zapisane ustawienia z menu rozwijanego. Uwaga Można zapisać maksymalnie 20 elementów.
Okno dialogowe Preferencje Aby otworzyć okno dialogowe Preferencje (Preferences), na ekranie programu ScanGear (sterownik skanera) kliknij przycisk Preferencje... (Preferences...). Na kartach Skaner (Scanner), Podgląd (Preview), Skanuj (Scan) i Ustawienia koloru (Color Settings) okna dialogowego Preferencje (Preferences) można określić zaawansowane ustawienia funkcji programu ScanGear.
Karta Skaner Na karcie Skaner (Scanner) można konfigurować następujące ustawienia. • Ustawienia ciche (Quiet Settings) Tryb cichej pracy umożliwia zmniejszenie hałasu towarzyszącego pracy urządzenia. Funkcji tej należy używać, gdy konieczne jest ograniczenie hałasu towarzyszącego pracy urządzenia, np. podczas skanowania lub drukowania w nocy. Aby ustawić tryb cichy, kliknij przycisk Ustawienia... (Settings...).
• Używaj trybu cichego przez określoną liczbę godzin (Use quiet mode during specified hours) To ustawienie powoduje zmniejszenie poziomu hałasu pracującego urządzenia w wybranym okresie. Wybierz ustawienia opcji Godzina rozpoczęcia (Start time) i Godzina zakończenia (End time), aby określić czas korzystania z trybu cichego. Ważne Czas określony w polach Godzina rozpoczęcia (Start time) i Godzina zakończenia (End time) musi mieć różne wartości.
Karta Podgląd Na karcie Podgląd (Preview) można konfigurować następujące ustawienia. • Podgląd przy uruchamianiu programu ScanGear (Preview at Start of ScanGear) Umożliwia wybranie sposobu wyświetlania podglądu po uruchomieniu programu ScanGear (sterownika skanera). • Wykonuj podgląd automatycznie (Automatically Execute Preview) Po uruchomieniu programu ScanGear będzie w nim automatycznie włączany podgląd.
Wymiary standardowe. • Mniejszy (Smaller) Wyświetlany obszar będzie o 5% mniejszy (wszerz i wzdłuż) niż przy ustawieniu standardowym. Uwaga Po zmianie wartości opcji Wielkość przycinania dla miniatury (Cropping Size for Thumbnail View) obrazy podglądu zostaną powtórnie wyświetlone, zgodnie z wybranym przycięciem. Ponowne wyświetlenie podglądu spowoduje utratę dopasowania kolorów i innych zastosowanych modyfikacji.
Karta Skanuj Na karcie Skanuj (Scan) można konfigurować następujące ustawienia. • Stan okna dialogowego programu ScanGear po zakończeniu skanowania (Status of ScanGear dialog after scanning) Umożliwia wybranie czynności wykonywanych w programie ScanGear (sterowniku skanera) po zakończeniu skanowania obrazów. • Zamknij program ScanGear automatycznie (Close ScanGear automatically) Wybór tego ustawienia powoduje powrót do oryginalnej aplikacji po zakończeniu skanowania.
Ten wybór jest preferowany, gdy wymagana jest duża szybkość drukowania zeskanowanych dokumentów. Jednak dokumenty nie są drukowane we właściwej kolejności. • Wydruk po stronie (Output by page) Powoduje wydrukowanie zeskanowanych dokumentów w odpowiedniej kolejności.
Karta Ustawienia koloru Na karcie Ustawienia koloru (Color Settings) można konfigurować następujące ustawienia. • Dopasowywanie kolorów Wybierz jedno z poniższych ustawień. Jedno z ustawień można wybrać, jeżeli opcja Tryb koloru (Color Mode) ma wartość Kolorowy (Color) lub Odcienie szarości (Grayscale). • Zalecane (Recommended) To ustawienie służy do żywego odwzorowania tonu dokumentu na ekranie. To ustawienie jest zalecane w zwykłych warunkach.
Kliknij przycisk Domyślne (Defaults), aby przywrócić domyślną wartość korekcji gamma monitora (1,80). Uwaga Wartość gamma monitora można znaleźć w podręczniku monitora. Jeśli podręcznik nie zawiera tej informacji, należy skontaktować się z producentem.
Umieszczanie przedmiotów (w przypadku skanowania z komputera) Objaśnienie sposobu umieszczania przedmiotów na płycie szklanej lub w podajniku ADF (Automatycznym podajniku dokumentów) skanera lub drukarki. Sposób umieszczenia przedmiotu, który ma zostać zeskanowany, musi być odpowiednio dobrany do jego rodzaju. W przeciwnym razie przedmioty mogą zostać zeskanowane nieprawidłowo. Ważne Na pokrywie dokumentów nie należy kłaść żadnych przedmiotów.
od brzegów/strzałki (znacznika wyrównania) płyty szklanej, mogą zostać zapisane jako pliki PDF. Aby zapisywać w formacie innym niż PDF, należy skanować po określeniu formatu danych. użytkowanego modelu, na stronie głównej dokumentu Podręcznik online. Umieszczanie wielu przedmiotów Między krawędziami płyty szklanej a przedmiotem oraz między poszczególnymi przedmiotami należy zachować odstępy wynoszące co najmniej 1 cm (0,4 cala) (obszar oznaczony poprzecznymi paskami).
2. Umieść dokumenty w ADF, a następnie dopasuj prowadnice dokumentów do ich szerokości. Wkładaj dokumenty stroną zadrukowaną skierowaną w górę do momentu, gdy urządzenie wyemituje sygnał dźwiękowy. Aby skanować obie strony dokumentów, umieszczaj je stroną zadrukowaną skierowaną w górę.
Dopasowywanie ramek przycinania (program ScanGear) „Przycinanie” jest czynnością polegającą na zaznaczeniu obszaru obrazu, który ma zostać zachowany, i usunięciu pozostałej części. Na kartach Tryb podstawowy (Basic Mode) i Tryb zaawansowany (Advanced Mode) można wyznaczać ramki przycinania (obszary skanowania) na obrazach wyświetlanych na ekranie w obszarze Podgląd. Po rozpoczęciu skanowania każdy obszar wyznaczony przez jedną z ramek przycinania zostanie zeskanowany jako osobny obraz.
Kursor po umieszczeniu go w obrębie ramki przycinania przybiera kształt przeciągnąć kursor, przenosząc całą ramkę przycinania. (Krzyżyk). Można kliknąć i Uwaga Na karcie Tryb zaawansowany (Advanced Mode) można określić rozmiar ramki przycinania, wprowadzając wartości w polach wejściowe (Input Settings). Ustawienia wejściowe (Szerokość) i (Wysokość) w obszarze Ustawienia Ramkę przycinania można obrócić o 90 stopni za pomocą przycisku (Przełącz współczynnik proporcji).
Można utworzyć wiele ramek przycinania i zastosować różne ustawienia skanowania do poszczególnych ramek. Można również wybrać wiele ramek przycinania, klikając je przy naciśniętym klawiszu Command. W przypadku zaznaczenia wielu ramek przycinania każda zmiana ustawień na karcie po prawej stronie okna programu ScanGear jest stosowana do wszystkich zaznaczonych ramek. Nowo utworzona ramka przycinania przejmuje ustawienia ostatniej ramki. Uwaga Można utworzyć do 12 ramek przycinania.
Uwagi ogólne (sterownik skanera) Program ScanGear (sterownik skanera) podlega ograniczeniom wymienionym poniżej. Używając sterownika skanera, należy mieć je na uwadze. Ograniczenia dotyczące sterownika skanera • W przypadku współużytkowania komputera przez kilku użytkowników lub podczas ponownego logowania po wylogowaniu z systemu wyświetlony może zostać komunikat, że program ScanGear jest w użyciu. W takim przypadku należy odłączyć kabel USB od komputera, a następnie podłączyć go ponownie.
lizacja sterownika skanera (ScanGear) Uzyskiwanie najnowszej wersji programu ScanGear (sterownika skanera) Usuwanie niepotrzebnego sterownika skanera (ScanGear) Przed instalacją sterownika skanera (ScanGear) Instalacja sterownika skanera (ScanGear) 164
Uzyskiwanie najnowszej wersji programu ScanGear (sterownika skanera) Często rozwiązaniem napotykanych problemów może się okazać uaktualnienie zainstalowanego programu ScanGear (sterownika skanera) do najnowszej wersji programu ScanGear. Sprawdzanie wersji programu ScanGear Uruchom program ScanGear i kliknij ikonę ScanGear.
Usuwanie niepotrzebnego sterownika skanera (ScanGear) Można usunąć program ScanGear (sterownik skanera), jeśli nie jest już używany. Przed usunięciem programu ScanGear (sterownika skanera) należy zamknąć wszystkie uruchomione aplikacje i odłączyć kabel USB łączący urządzenie z komputerem. 1. Usuń program ScanGear. W menu Idź (Go) programu Finder wybierz polecenie Komputer (Computer).
Przed instalacją sterownika skanera (ScanGear) Przed zainstalowaniem programu ScanGear (sterownika skanera) należy sprawdzić poniższe elementy. Należy je sprawdzić również w przypadku, gdy nie można zainstalować programu ScanGear. Stan urządzenia • Jeśli urządzenie i komputer są połączone za pomocą kabla USB, odłącz kabel USB od komputera. • Wyłącz urządzenie. Ustawienia komputera • Zakończ działanie wszystkich bieżących aplikacji. • Zaloguj się jako administrator komputera.
Instalacja sterownika skanera (ScanGear) Odwiedź naszą witrynę sieci Web i pobierz najnowszą wersję programu ScanGear (sterownika skanera). Aby zainstalować pobrany program ScanGear, wykonaj poniższe czynności. 1. Podłącz dysk. Dwukrotnie kliknij plik pobranego obrazu dysku. Plik zostanie zdekompresowany, a następnie dysk zostanie podłączony. 2. Uruchom instalatora. Kliknij dwukrotnie plik „.pkg” na zdekompresowanym dysku. Instalacja rozpocznie się. 3. Zainstaluj sterownik.
Przydatne informacje na temat skanowania Dopasowywanie ramek przycinania (program IJ Scan Utility) Rozdzielczość Formaty danych Dopasowywanie kolorów 169
Dopasowywanie ramek przycinania (program IJ Scan Utility) „Przycinanie” jest czynnością polegającą na zaznaczeniu obszaru obrazu, który ma zostać zachowany, i usunięciu pozostałej części. W oknie Złączenie obrazu (Image Stitch) można wyznaczyć ramkę przycinania na obrazie wyświetlonym w obszarze Podgląd.
Rozdzielczość Dane tworzące zeskanowany obraz to zbiór punktów z określonymi parametrami jasności i koloru. Gęstość tych punktów jest nazywana „rozdzielczością”. Przekłada się ona na liczbę szczegółów, które zawiera obraz. Jednostką rozdzielczości są punkty na cal (dpi). Dpi to liczba punktów na cal (2,5 cm). Im wyższa rozdzielczość (wartość liczbowa), tym więcej szczegółów zawiera zeskanowany obraz, i odwrotnie. Ustawianie rozdzielczości Rozdzielczość można ustawiać na poniższych ekranach.
Uwaga Jeśli zeskanowany obraz będzie drukowany w powiększeniu, należy skanować z rozdzielczością większą niż zalecana powyżej.
Formaty danych Podczas zapisywania zeskanowanych obrazów można wybrać format danych. Należy wybrać format najbardziej odpowiedni do przeznaczenia obrazu i docelowej aplikacji. Dostępne formaty danych zmieniają się w zależności od aplikacji i systemu operacyjnego (Windows lub Mac OS). Poniżej opisano poszczególne formaty danych obrazu. PNG (standardowe rozszerzenie pliku: .png) Format danych stosowany często w witrynach sieci Web. Format PNG umożliwia edytowanie zapisanych obrazów.
Dopasowywanie kolorów „Dopasowywanie kolorów” polega na wprowadzaniu korekt zapewniających zgodność odcieni kolorów między oryginalnym przedmiotem, ekranem monitora i kolorowym wydrukiem. W skanerze lub drukarce odcienie kolorów są korygowane w sposób przedstawiony poniżej.
Ekran menu i ustawień programu IJ Network Scanner Selector EX Program IJ Network Scanner Selector EX umożliwia wybranie skanerów i drukarek, które będą używane do skanowania lub drukowania przez sieć z komputera lub panelu operacyjnego. Ważne Jeśli nie można skanować przez sieć, pobierz najnowszą wersję sterowników ScanGear (sterownika skanera) z naszej witryny i wykonaj aktualizację.
Ekran Ustawienia skanowania z komputera Przed rozpoczęciem skanowania przez sieć trzeba wybrać skaner lub drukarkę za pomocą programu IJ Network Scanner Selector EX. W menu Idź (Go) programu Finder wybierz opcję Aplikacje (Applications), a następnie kolejno kliknij dwukrotnie: folder Canon Utilities, folder IJ Network Scanner Selector EX oraz ikonę Canon IJ Network Scanner Selector EX, aby wyświetlić ekran Ustawienia skanowania z komputera.
• Skanery (Scanners) Zostaną wyświetlone nazwy usług Bonjour lub adresy MAC skanerów i drukarek, które mogą być używane przez sieć. Do skanowania z panelu operacyjnego można wybrać maksymalnie trzy skanery i drukarki jednocześnie. Wybranie skanera lub drukarki automatycznie włącza skanowanie z panelu operacyjnego.
Informacje o programie IJ Network Scanner Selector EX Jeśli zainstalowane są sterowniki ScanGear (sterownik skanera), program IJ Network Scanner Selector EX jest uruchamiany automatycznie, aby umożliwić skanowanie przez sieć z komputera lub panelu operacyjnego skanera. Aby program IJ Scanner Selector EX nie uruchamiał się automatycznie, należy zmienić ustawienia, wykonując poniższą procedurę. Ważne Program IJ Network Scanner Selector EX można skonfigurować tak, aby nie był uruchamiany automatycznie.
Umieszczanie przedmiotów (w przypadku skanowania z komputera) Objaśnienie sposobu umieszczania przedmiotów na płycie szklanej lub w podajniku ADF (Automatycznym podajniku dokumentów) skanera lub drukarki. Sposób umieszczenia przedmiotu, który ma zostać zeskanowany, musi być odpowiednio dobrany do jego rodzaju. W przeciwnym razie przedmioty mogą zostać zeskanowane nieprawidłowo. Ważne Na pokrywie dokumentów nie należy kłaść żadnych przedmiotów.
od brzegów/strzałki (znacznika wyrównania) płyty szklanej, mogą zostać zapisane jako pliki PDF. Aby zapisywać w formacie innym niż PDF, należy skanować po określeniu formatu danych. użytkowanego modelu, na stronie głównej dokumentu Podręcznik online. Umieszczanie wielu przedmiotów Między krawędziami płyty szklanej a przedmiotem oraz między poszczególnymi przedmiotami należy zachować odstępy wynoszące co najmniej 1 cm (0,4 cala) (obszar oznaczony poprzecznymi paskami).
2. Umieść dokumenty w ADF, a następnie dopasuj prowadnice dokumentów do ich szerokości. Wkładaj dokumenty stroną zadrukowaną skierowaną w górę do momentu, gdy urządzenie wyemituje sygnał dźwiękowy. Aby skanować obie strony dokumentów, umieszczaj je stroną zadrukowaną skierowaną w górę.
Skanowanie z panelu operacyjnego urządzenia Przekazywanie zeskanowanych danych do komputera za pomocą panelu operatora urządzenia Podstawy Dołączanie zeskanowanych danych do wiadomości e-mail za pomocą panelu operacyjnego urządzenia Zapisywanie zeskanowanych danych w napędzie flash USB przy użyciu panelu operacyjnego urządzenia Usuwanie zeskanowanych danych zapisanych w napędzie flash USB Wprowadzanie ustawień pozycji menu za pomocą panelu operacyjnego urządzenia Ustawienia skanowania sieciowego Wybieranie
Przekazywanie zeskanowanych danych do komputera za pomocą panelu operatora urządzenia Zeskanowane dane można przekazać do komputera przy użyciu panelu operacyjnego urządzenia. Przed przekazaniem zeskanowanych danych do komputera należy sprawdzić, czy są spełnione następujące warunki: • Program ScanGear (sterownik skanera) został zainstalowany.
Uwaga Jeśli na wyświetlaczu LCD pojawi się ekran gotowości do skanowania umożliwiający przekazywanie danych do komputera podłączonego przez złącze USB, naciśnij lewy przycisk Funkcja (Function), aby wyświetlić ekran wyboru miejsca zapisywania danych. Wybierz komputer, na którym chcesz zapisać zeskanowane dane, postępując według poniższej procedury. 1. Wybierz opcję Komputer (PC), a następnie naciśnij przycisk OK. wybierz komputer, do którego chcesz przesłać zeskanowane dane, a 2.
Ważne Wybór opcji Skanow. autom. (Auto scan) jest możliwy, tylko jeśli zeskanowane dane są przekazywane do komputera podłączonego przy użyciu kabla USB. Załaduj oryginały zgodnie z ich typem, ponieważ w innym przypadku niektóre z nich mogą nie zostać poprawnie zeskanowane. Szczegółowe informacje na temat ładowania oryginałów można znaleźć w części: Ładowanie oryginałów Można skanować następujące elementy: Fotografie, pocztówki, wizytówki, czasopisma, gazety, dokumenty oraz płyty CD/DVD.
Ważne Jeśli po wybraniu ustawienia Skanow. autom. (Auto scan) jakość skanowania jest niezadowalająca, w zależności od oryginału wybierz w kroku 3 opcję Dokument (Document) lub Fotograficzna (Photo), a następnie określ rozmiar skanowania lub inne ustawienia w kroku 4.
Dołączanie zeskanowanych danych do wiadomości e-mail za pomocą panelu operacyjnego urządzenia Za pomocą panelu operacyjnego urządzenia zeskanowane dane można dołączyć do wiadomości e-mail. Przed dołączeniem zeskanowanych danych do wiadomości e-mail należy sprawdzić, czy są spełnione następujące warunki: • Program ScanGear (sterownik skanera) został zainstalowany.
W przypadku połączenia przy użyciu kabla USB wybierz opcję Lokalny (USB) (Local (USB)), a w przypadku komputera podłączonego do sieci wybierz komputer, do którego mają być przekazane dane. Zostanie wyświetlony ekran gotowości skanowania. 5. Wybierz typ dokumentu za pomocą przycisków . Dokument (Document) Skanowanie oryginału umieszczonego na płycie szklanej lub w ADF jako danych dokumentu przy zastosowaniu ustawień wprowadzonych za pomocą opcji Ust. skanow. (Scan settings).
• Jeśli na ekranie ustawień skanowania wybrano dla opcji Format ustawienie JPEG, urządzenie rozpocznie skanowanie, a zeskanowane dane zostaną przekazane do komputera i dołączone do wiadomości e-mail. • Jeśli opcja Format na ekranie ustawień skanowania jest ustawiona na wartość PDF lub Compact PDF, to po zakończeniu skanowania zostanie wyświetlony ekran z pytaniem o potwierdzenie dalszego skanowania. Jeśli chcesz kontynuować, załaduj oryginał na płytę szklaną i rozpocznij skanowanie.
Zapisywanie zeskanowanych danych w napędzie flash USB przy użyciu panelu operacyjnego urządzenia Zeskanowane dane można zapisać w napędzie flash USB przy użyciu panelu operacyjnego urządzenia.
6. Wybierz typ dokumentu za pomocą przycisków . Dokument (Document) Skanowanie oryginału umieszczonego na płycie szklanej lub w ADF jako danych dokumentu przy zastosowaniu ustawień wprowadzonych za pomocą opcji Ust. skanow. (Scan settings). Fotografii (Photo) Skanowanie oryginału umieszczonego na płycie szklanej jako danych fotograficznych przy zastosowaniu ustawień wprowadzonych za pomocą opcji Ust. skanow. (Scan settings). 7.
Skanując oryginały w trybie ciągłym można zapisać maksymalnie 100 stron obrazów w jednym pliku PDF. Po zakończeniu skanowania usuń oryginał z płyty szklanej lub z otworu wyjściowego dokumentu. Uwaga Jeśli podczas skanowania w napędzie flash USB skończy się wolne miejsce, zapisane zostaną jedynie obrazy już zeskanowane. Można zapisać maksymalnie 2000 plików zawierających zeskanowane dane w formatach PDF i JPEG.
Usuwanie zeskanowanych danych zapisanych w napędzie flash USB Zeskanowane dane zapisane w napędzie flash USB można usuwać za pomocą panelu operacyjnego. 1. Upewnij się, że urządzenie jest włączone. Sprawdzanie, czy jest włączone zasilanie 2. Włóż napęd flash USB do portu napędu flash USB. Wkładanie napędu USB 3. Naciśnij przycisk SKANUJ (SCAN). Wyświetlony zostanie ekran wyboru miejsca zapisywania danych.
7. Za pomocą przycisków wybierz na ekranie potwierdzenia opcję Tak (Yes), a następnie naciśnij przycisk OK. Urządzenie rozpocznie usuwanie pliku.
Wprowadzanie ustawień pozycji menu za pomocą panelu operacyjnego urządzenia Można zmieniać ustawienia skanowania, np. rozmiar skanowania, rozdzielczość czy format danych. Gdy wyświetlany jest ekran gotowości skanowania, naciśnij prawy przycisk Funkcja (Function), aby wybrać element ustawień. Za pomocą przycisków wybierz element ustawień, określ jego ustawienie za pomocą przycisków , a następnie naciśnij przycisk OK.
1. Rozm.sk. (Scan size) Umożliwia określenie rozmiaru oryginału. Uwaga Jeśli wybrano ustawienie Legal, załaduj oryginał do ADF. Po wybraniu ustawienia 10x15cm(4"x6") (4"x6"(10x15cm)), 13x18cm(5"x7") (5"x7"(13x18cm)) lub Skanow. autom. (Auto scan) umieść oryginał na płycie szklanej. 2. Format Wybierz format skanowanych danych. 3. Roz.skan (Scan res) (Rozdzielczość skanowania) Wybierz rozdzielczość skanowania. 4.
Ustawienia skanowania sieciowego Skaner lub drukarkę można podłączyć do sieci, aby udostępnić wielu komputerom lub skanować obrazy do wybranego komputera. Ważne Skanowanie może wykonywać tylko jeden użytkownik w danym momencie. Uwaga Przed użyciem instalacyjnego dysku CD-ROM zakończ konfigurację sieci w skanerze lub drukarce. Skanowanie przy użyciu połączenia sieciowego trwa dłużej niż w przypadku połączenia USB. Aby umożliwić skanowanie za pośrednictwem sieci, należy wprowadzić następujące ustawienia.
Ważne Jeśli w sieci występuje wiele skanerów, pojawi się wiele nazw modeli. W takim przypadku można wybrać jeden skaner dla każdego modelu. Szczegółowe informacje na ten temat można znaleźć w części „Ekran menu i ustawień programu IJ Network Scanner Selector EX” dotyczącej użytkowanego modelu, na stronie głównej dokumentu Podręcznik online. 3. Kliknij przycisk OK.
4. Kliknij przycisk (Ustawienia ogólne), a następnie w obszarze Nazwa produktu (Product Name) kliknij przycisk Wybierz (Select). Pojawi się ekran narzędzia IJ Network Scanner Selector EX dotyczący ustawień skanowania z komputera. Wybierz skaner, którego chcesz używać, a następnie kliknij przycisk OK. 5. Kliknij przycisk OK w oknie dialogowym Ustawienia (Ustawienia ogólne) (Settings (General Settings)). Ponownie pojawi się ekran główny programu IJ Scan Utility.
Pojawi się ekran Ustawienia skanowania z panelu operacyjnego. 3. Wybierz skaner lub drukarkę w obszarze Skanery (Scanners), a następnie kliknij przycisk OK. Dla skanera lub drukarki wybierana jest domyślna nazwa usługi Bonjour. Jeśli usługa Bonjour jest wyłączona, pojawi się adres MAC skanera lub drukarki. Uwaga Gdy za pośrednictwem sieci podłączonych jest wiele skanerów, można wybrać maksymalnie trzy skanery.
Uwaga Jeśli nazwa usługi Bonjour lub adres MAC skanera bądź drukarki są wyświetlane w szarym kolorze lub nie można ich wybrać, sprawdź poniższe warunki i kliknij przycisk OK, aby zamknąć ekran. Następnie otwórz go ponownie i wybierz skaner lub drukarkę. Program ScanGear (sterownik skanera) został zainstalowany Po zainstalowaniu programu ScanGear skonfigurowano ustawienia sieciowe skanera lub drukarki. Działa komunikacja sieciowa między skanerem lub drukarką a komputerem.
Wybieranie za pomocą programu IJ Scan Utility reakcji na polecenia inicjowane z panelu operacyjnego Program IJ Scan Utility umożliwia określenie reakcji na polecenia w przypadku skanowania za pomocą panelu operacyjnego. Uwaga W poniższych przykładach posłużono się ekranami wyboru reakcji podczas automatycznego skanowania za pomocą panelu operacyjnego. 1. Uruchom program IJ Scan Utility. Uruchamianie programu IJ Scan Utility 2. Kliknij przycisk Ustawienia (Settings...).
4. Korekcje obrazu określ w obszarze Opcje skanowania (Scan Options). 5. Nazwę pliku i inne ustawienia wprowadź w obszarze Zapisz ustawienia (Save Settings). 6. W obszarze Ustawienia aplikacji (Application Settings) wybierz aplikację, która ma być uruchamiana po zakończeniu skanowania.
7. Kliknij przycisk OK. Po rozpoczęciu skanowania za pomocą panelu operacyjnego reakcje będą wywoływane odpowiednio do wprowadzonych ustawień.