MX720 series Online kézikönyv Beolvasás magyar (Hungarian)
Beolvasás Beolvasás számítógépről Beolvasás az IJ Scan Utility segédprogrammal Beolvasás a használt szoftveralkalmazással (ScanGear) Hasznos információk letapogatáshoz Az IJ Network Scanner Selector EX menüje és beállítási képernyője Egyéb beolvasási módszerek Anyagok elhelyezése (számítógépről történő beolvasás esetén) Beolvasás a készülék kezelőpaneljének használatával A beolvasott adatok továbbítása a számítógépre a készülék kezelőpaneljének segítségével Alapszintű A beolvasott adatok e-mailhez csatolása
Beolvasás számítógépről Beolvasás az IJ Scan Utility segédprogrammal Beolvasás a használt szoftveralkalmazással (ScanGear) Hasznos információk letapogatáshoz Az IJ Network Scanner Selector EX menüje és beállítási képernyője Egyéb beolvasási módszerek Anyagok elhelyezése (számítógépről történő beolvasás esetén) 3
Beolvasás a készülék kezelőpaneljének használatával A beolvasott adatok továbbítása a számítógépre a készülék kezelőpaneljének segítségével Alapszintű A beolvasott adatok e-mailhez csatolása a készülék kezelőpaneljének segítségével Beolvasott adatok mentése USB flash meghajtóra a készülék kezelőpaneljének segítségével Beolvasott adatok törlése az USB flash meghajtóról Értékek beállítása a készülék kezelőpaneljén Beállítások hálózaton keresztül történő beolvasás esetén Parancsokra adott válasz kiválasztása a
Beolvasás az IJ Scan Utility segédprogrammal Mi az IJ Scan Utility (lapolvasószoftver)? Az IJ Scan Utility elindítása Egyszerű letapogatás automatikus beolvasással Alapszintű Fotók szkennelése Dokumentumok szkennelése Szkennelés kedvenc beállításokkal Az üveglapnál nagyobb méretű anyagok beolvasása (Összefűzés-segítő) Több anyag egyidejű beolvasása Több dokumentum egyidejű beolvasása az ADF-ből (automatikus lapadagoló) A dokumentumok mindkét oldalának egyidejű beolvasása Mentés a beolvasás eredményének el
Mi az IJ Scan Utility (lapolvasószoftver)? Az IJ Scan Utility egy olyan alkalmazás, amely fényképek, dokumentumok stb. egyszerű beolvasását teszi lehetővé. Az IJ Scan Utility főképernyőjén bármely tevékenységet elvégezhet a beolvasástól a mentésig egyszerűen a megfelelő ikonra történő egyetlen kattintással.
Fontos Bizonyos funkciók csak a My Image Garden telepítésével válnak elérhetővé. Megjegyzés Az együttműködéshez választott alkalmazások beállításának ismertetését lásd: „A Beállítások párbeszédpanel”.
Az IJ Scan Utility elindítása Megjegyzés Ha több lapolvasót használ vagy a csatlakozást USB-kapcsolatról hálózati kapcsolatra módosította, akkor végezze el a hálózati környezet beállítását az IJ Scan Utility programban. Beállítások hálózaton keresztül történő beolvasás esetén Válassza a Start menü Minden program (All Programs) > Canon Utilities > IJ Scan Utility > IJ Scan Utility parancsát az IJ Scan Utility elindításához.
5. Győződjön meg róla, hogy a Beolvasási irány (Scan Direction) beállítás értéke Beolvasás balról (Scan from Left). 6. Helyezze az üveglapra fejjel lefelé fordítva az anyagnak azt az oldalát, amelyet a képernyő bal oldalán kíván megjeleníteni. 7. Kattintson az 1-es kép beolvasásának elindítása (Start Scanning Image 1) gombra. A lapolvasó beolvassa az első részt, és megjeleníti az 1-es területen. Megjegyzés Kattintson a Mégse (Cancel) gombra a beolvasás megszakításához.
8. Helyezze az üveglapra fejjel lefelé fordítva az anyagnak azt az oldalát, amelyet a képernyő jobb oldalán kíván megjeleníteni. 9. Kattintson a 2-es kép beolvasásának elindítása (Start Scanning Image 2) gombra. A lapolvasó beolvassa a második részt, és megjeleníti a 2-es területen. Megjegyzés Kattintson a Mégse (Cancel) gombra a beolvasás megszakításához. 10. Állítsa be a beolvasott képet a kívánt módon.
Megjegyzés A Vágási keretek beállítása (Adjust cropping frames) jelölőnégyzettel megadhatja a menteni kívánt területet. Vágási keretek beállítása (IJ Scan Utility) A dokumentum újbóli beolvasásához jelölje ki a képet a megtekintési területen vagy jelölje ki a megfelelő indexképet a képernyő felső részén, majd kattintson a kép törlődik, így újból beolvashatja a dokumentumot. (Törlés) gombra. A kijelölt 11. Kattintson a Mentés (Save) gombra. A program menti az egyesített képet.
Több anyag egyidejű beolvasása Beolvashat egyszerre az üveglapra helyezett két vagy több fotót (kis anyagot), majd külön képként mentheti őket. Fontos A következő típusok esetleg nem vághatók megfelelően. Ebben az esetben a ScanGear (lapolvasó illesztőprogram) alkalmazás teljes kép nézetében állítsa be a vágási kereteket (beolvasási területeket), majd ismételje meg a beolvasást. Fehéres hátterű fényképek Fehér lapra nyomtatott anyagok, kézzel írt dokumentumok, névjegyek stb.
5. A beolvasni kívánt anyagoknak megfelelően adja meg a Forrás kiválasztása (Select Source) értékét. 6. Válassza ki az Automatikus beolvasás (Auto scan) értéket a Papírméret (Paper Size) beállításnál, majd kattintson az OK gombra.
A IJ Scan Utility főképernyője újra megjelenik. Megjegyzés A Beállítások párbeszédpanelen megadható beállításokról a következő oldalakon olvashat. A Beállítások (Fényképbeolvasás) párbeszédpanel A Beállítások (Dokumentumbeolvasás) párbeszédpanel A Beállítások (Egyéni beolvasás) párbeszédpanel 7. Kattintson az Egyéni (Custom) gombra. Az anyagok egyszerre lesznek beolvasva. Megjegyzés Kattintson a Mégse (Cancel) gombra a beolvasás megszakításához. A beolvasott képek a Beáll.-ok... (Settings...
Több dokumentum egyidejű beolvasása az ADF-ből (automatikus lapadagoló) Helyezzen több dokumentumot az ADF-be (automatikus lapadagoló), és végezze el egy művelettel a beolvasást. Ebben a részben elmagyarázzuk, hogyan lehet letapogatni a dokumentumok egyik oldalát. A dokumentumok mindkét oldalának automatikus beolvasásához lásd: A dokumentumok mindkét oldalának egyidejű beolvasása.
5. A beolvasni kívánt dokumentumoknak megfelelően adja meg a Forrás kiválasztása (Select Source) beállítás értékét. Ha csak a dokumentumok első oldalát szeretné beolvasni, válassza a Dokumentum (ADF/üveglap) (Document (ADF/Platen)) vagy a Dokumentum (ADF egyoldalas) (Document (ADF Simplex)) beállítást. A dokumentum első és hátoldalának beolvasásához válassza a Dokumentum (ADF kétoldalas) (Document (ADF Manual Duplex)) beállítást. 6.
Ha végzett a beállításokkal, kattintson az OK gombra. A IJ Scan Utility főképernyője újra megjelenik. Megjegyzés A Beállítások párbeszédpanelen megadható beállításokról a következő oldalakon olvashat. A Beállítások (Dokumentumbeolvasás) párbeszédpanel A Beállítások (Egyéni beolvasás) párbeszédpanel 7. Kattintson a Dokumentum (Document) gombra. Ezzel a letapogatás elindul. Megjegyzés Kattintson a Mégse (Cancel) gombra a beolvasás megszakításához.
A következő leírásokban a Tájolás (Orientation) beállítás Álló (Portrait) értékével végzett beolvasás képernyői szerepelnek példaként. Ha a Kötési oldal (Binding Side) beállítás Hosszú szél (Long edge) lehetőségét választja kötési oldalnak a Dokum.beolv. tájolási beállításai... (Document Scan Orientation Settings...) beállításnál Helyezze el a dokumentumokat, miután 180 fokkal elforgatta a kimeneti dokumentumokat.
A dokumentumok mindkét oldalának egyidejű beolvasása Az ADF (automatikus lapadagoló) használatával egyidejűleg beolvashatja az egyes dokumentumok mindkét oldalát. Megjegyzés Egyszerre több dokumentumot olvashat be az ADF-ből, amikor az Automatikus (Auto), a Dokumentum (Document), az Egyéni (Custom) vagy a ScanGear beállítást használja a beolvasáshoz.
5. Adja meg a Forrás kiválasztása (Select Source) beállításhoz a Dokumentum (ADF/üveglap) (Document (ADF/Platen)) vagy a Dokumentum (ADF automatikus kétoldalas) (Document (ADF Auto Duplex)) lehetőséget. Megjegyzés Jelölje be a Mindkét oldal beolvasása az ADF-ből történő letapogatás esetén (Scan both sides when scanning from the ADF) jelölőnégyzetet a Beolvasási beállítások (Scan Options) párbeszédpanelen, ha a Dokumentum (ADF/üveglap) (Document (ADF/Platen)) lehetőséggel olvas be. 6.
Tájolás (Orientation) és a Kötési oldal (Binding Side) beállítást. A hátoldalak beolvasásánál a dokumentumok elhelyezésének módja a Kötési oldal (Binding Side) beállítástól függ. Kattintson a Dokumentum kimeneti beállítása... (Document Output Setting...) elemre a beolvasott dokumentumok kimenetének megadásához. A megjelenő párbeszédpanelen beállíthatja a kimenetet. Ha végzett a beállításokkal, kattintson az OK gombra. A IJ Scan Utility főképernyője újra megjelenik.
Mentés a beolvasás eredményének ellenőrzése után Ellenőrizheti a beolvasás eredményét, majd a számítógépre mentheti a képeket. Fontos Nem ellenőrizheti a beolvasás eredményét Automatikus (Auto) beolvasáskor vagy ha a kezelőpanelről olvas be. Megjegyzés Fényképek beolvasási képernyői szerepelnek példaként a következő leírásokban. 1. Indítsa el az IJ Scan Utility alkalmazást. Az IJ Scan Utility elindítása 2. Kattintson a Beáll.-ok... (Settings...) gombra. Megjelenik a Beállítások párbeszédpanel.
A IJ Scan Utility főképernyője újra megjelenik. Megjegyzés A Beállítások párbeszédpanelen megadható beállításokról a következő oldalakon olvashat. A Beállítások (Fényképbeolvasás) párbeszédpanel A Beállítások (Dokumentumbeolvasás) párbeszédpanel A Beállítások (Egyéni beolvasás) párbeszédpanel A Beállítások (Beolvasás és egyesítés) párbeszédpanel A Beállítások (ScanGear) párbeszédpanel 5. Kattintson a Fénykép (Photo) gombra. Ezzel a letapogatás elindul.
7. Kattintson az OK gombra. A letapogatott képek a beállításoknak megfelelően mentésre kerülnek.
Beolvasott képek küldése e-mailben A beolvasott képeket elküldheti e-mailben. Megjegyzés Fényképek beolvasási képernyői szerepelnek példaként a következő leírásokban. 1. Indítsa el az IJ Scan Utility alkalmazást. Az IJ Scan Utility elindítása 2. Kattintson a Beáll.-ok... (Settings...) gombra. Megjelenik a Beállítások párbeszédpanel. A Beállítások párbeszédpanel 3. Kattintson a Fényképbeolvasás (Photo Scan) gombra. 4.
Megjegyzés A csatoláshoz használni kívánt levelezőprogramokat a legördülő menüből választhatja ki. Ha a Nincs (csatolás kézzel) (None (Attach Manually)) beállítás van kiválasztva, kézzel csatolja e-mailhez a beolvasott és mentett képeket. 5. Kattintson az OK gombra. A IJ Scan Utility főképernyője újra megjelenik. Megjegyzés A Beállítások párbeszédpanelen megadható beállításokról a következő oldalakon olvashat.
A Beállítások (ScanGear) párbeszédpanel 6. Kattintson a Fénykép (Photo) gombra. Ezzel a letapogatás elindul. Ha a beolvasás befejeződik, elindul a megadott levelezőprogram, amelyben a képek egy új üzenethez lesznek csatolva. Megjegyzés Kattintson a Mégse (Cancel) gombra a beolvasás megszakításához. A beolvasott képek mentése a Beállítások párbeszédpanelen megadottak szerint történik.
A beolvasott képeken található szöveg felismerése (OCR) Beolvassa a szöveget a beolvasás alatt álló folyóiratokból és újságokból, majd megjeleníti azt a Jegyzettömb alkalmazásban (a Windows tartozéka). Megjegyzés Lehetősége van a szöveg kinyerésére, amikor a Dokumentum (Document), az Egyéni (Custom) vagy a ScanGear beállítást használja a beolvasáshoz. Dokumentumok beolvasási képernyői szerepelnek példaként a következő leírásokban. 1. Indítsa el az IJ Scan Utility alkalmazást.
Megjegyzés Ha a My Image Garden opciót választja, akkor az alkalmazás kinyeri a képben lévő szöveget a kép beolvasása után, és megjelenik a Jegyzettömb programban (amely a Windows tartozéka). 5. Kattintson az OK gombra. A IJ Scan Utility főképernyője újra megjelenik. Megjegyzés A Beállítások párbeszédpanelen megadható beállításokról a következő oldalakon olvashat. A Beállítások (Dokumentumbeolvasás) párbeszédpanel A Beállítások (Egyéni beolvasás) párbeszédpanel A Beállítások (ScanGear) párbeszédpanel 6.
Ezzel a letapogatás elindul. A beolvasás után a program menti a beolvasott képet a beállítások szerint, a kinyert szöveg pedig megjelenik a megadott alkalmazásban. Megjegyzés Kattintson a Mégse (Cancel) gombra a beolvasás megszakításához. A Jegyzettömb alkalmazásban (a Windows tartozéka) megjelenő szöveg csak tájékoztató jellegű. A következő dokumentumtípusok képeiben lévő szöveg lehet, hogy nem érzékelhető megfelelően.
Az IJ Scan Utility képernyői Az IJ Scan Utility főképernyője A Beállítások párbeszédpanel A Beállítások (Automatikus beolvasás) párbeszédpanel A Beállítások (Fényképbeolvasás) párbeszédpanel A Beállítások (Dokumentumbeolvasás) párbeszédpanel A Beállítások (Egyéni beolvasás) párbeszédpanel A Beállítások (Beolvasás és egyesítés) párbeszédpanel A Beállítások (ScanGear) párbeszédpanel A Beállítások (Mentés számítógépre (automatikus)) párbeszédpanel A Beállítások (Mentés számítógépre (fénykép)) párbeszédpanel A
Az IJ Scan Utility főképernyője Válassza a Start menü Minden program (All Programs) > Canon Utilities > IJ Scan Utility > IJ Scan Utility parancsát az IJ Scan Utility elindításához. Végezze el a műveletet a beolvasástól a mentésig egyszerűen a megfelelő ikonra történő kattintással. • Terméknév (Product Name) Megjeleníti annak a terméknek a nevét, amelyet az aktuális beállítás szerint az IJ Scan Utility használ.
Megjeleníti a Beállítások párbeszédpanelt, amelyen a beolvasási/mentési beállításokat és a beolvasás utáni műveletet adhatja meg.
A Beállítások párbeszédpanel A Beállítások párbeszédpanel három lapot tartalmaz: (Beolvasás számítógépről), (Beolvasás a kezelőpanel használatával) és (Általános beállítások). Amikor rákattint az egyik lapra, megváltozik a piros keretben megjelenített tartalom, és megadhatja az egyes lapokon elérhető funkciók speciális beállításait. (Beolvasás számítógépről) lap Megadhatja, hogy mi történjen az IJ Scan Utility programból vagy a My Image Garden alkalmazásból végzett beolvasás esetén.
(Általános beállítások) lap Megadhatja a használt terméket, az e-mail mellékletek fájlméretére vonatkozó korlátozást, a képek lévő szöveg felismeréséhez használt nyelvet, valamint a képek ideiglenes tárolásához használt mappát.
A Beállítások (Automatikus beolvasás) párbeszédpanel A Beállítások (Automatikus beolvasás) (Settings (Auto Scan)) párbeszédpanel megjelenítéséhez a (Beolvasás számítógépről) lapon kattintson az Automatikus beolvasás (Auto Scan) elemre. A Beállítások (Automatikus beolvasás) (Settings (Auto Scan)) párbeszédpanelen megadhatja a dokumentumtípus automatikus meghatározásával végzett beolvasás speciális beállításait.
Megjegyzés A moire minta csökkentéséhez a Beállítások (Dokumentumbeolvasás) (Settings (Document Scan)) vagy a Beállítások (Egyéni beolvasás) (Settings (Custom Scan)) párbeszédpanel Forrás kiválasztása (Select Source) beállításánál válassza a Magazin (Magazine) értéket, majd kattintson a Dokumentum (Document) vagy az Egyéni (Custom) elemre az IJ Scan Utility főképernyőjén.
Amikor a Beállítások párbeszédpanelt a My Image Garden szolgáltatásból jeleníti meg, ez a lehetőség nem jelenik meg. (3) Alkalmazás-beállítások terület • Megnyitás egy alkalmazással (Open with an application) Válassza ezt a lehetőséget a beolvasott képek helyesbítéséhez vagy javításához. Az alkalmazást a legördülő menüből választhatja ki.
A Beállítások (Fényképbeolvasás) párbeszédpanel A Beállítások (Fényképbeolvasás) (Settings (Photo Scan)) párbeszédpanel megjelenítéséhez a (Beolvasás számítógépről) lapon kattintson az Fényképbeolvasás (Photo Scan) elemre. A Beállítások (Fényképbeolvasás) (Settings (Photo Scan)) párbeszédpanelen speciális beolvasási beállításokat adhat meg az olyan anyagok beolvasásához mint a fényképek.
Megjegyzés Kattintson az Alapértelmezés (Defaults) lehetőségre a megadott beállítások visszaállításához az alapértelmezett értékre. • Felbontás (Resolution) Adja meg a beolvasni kívánt anyag felbontását. Minél magasabb a felbontás (érték), annál részletesebb a kép. Felbontás • Beolvasott képek tömörítése továbbításkor (Compress scanned images upon transfer) Tömöríti a beolvasott képeket a számítógépre történő továbbításkor. Ez akkor hasznos, ha a lapolvasó vagy a nyomtató lassú interfésszel, például USB1.
Amikor a Beállítások párbeszédpanelt a My Image Garden szolgáltatásból jeleníti meg, ez a lehetőség nem jelenik meg. • Beolvasási eredmények ellenőrzése (Check scan results) Beolvasás után megjeleníti a Beállítások mentése (Save Settings) párbeszédpanelt. A Beállítások mentése párbeszédpanel Fontos Amikor a Beállítások párbeszédpanelt a My Image Garden szolgáltatásból jeleníti meg, ez a lehetőség nem jelenik meg.
A Beállítások (Dokumentumbeolvasás) párbeszédpanel A Beállítások (Dokumentumbeolvasás) (Settings (Document Scan)) párbeszédpanel megjelenítéséhez a (Beolvasás számítógépről) lapon kattintson a Dokumentumbeolvasás (Document Scan) elemre. A Beállítások (Dokumentumbeolvasás) (Settings (Document Scan)) párbeszédpanelen speciális beolvasási beállításokat adhat meg az olyan anyagok beolvasásához, mint a dokumentumok.
Megjegyzés Ha a Dokumentum (ADF/üveglap) (Document (ADF/Platen)) beállítás van kiválasztva, és az üveglapra és az ADF-be is helyezett dokumentumokat, a készülék az ADF-be helyezett dokumentumokat fogja beolvasni. • Színmód (Color Mode) Válassza ki a színmódot az anyag beolvasásához. Fontos A Fekete-fehér (Black and White) beállítás választásához törölje a Beolvasott képek tömörítése továbbításkor (Compress scanned images upon transfer) jelölőnégyzet jelölését.
A Kötési oldal (Binding Side) nem adható meg, ha csak a dokumentumok elülső oldalának beolvasása van beállítva. • Dokumentum kimeneti beállítása... (Document Output Setting...
A nyomtatott anyagok pontok finom halmazaként vannak ábrázolva. A moire minta egy olyan jelenség, amely esetén egyenetlen elosztású részek vagy csíkozott minták keletkeznek az ilyen finom pontokból álló nyomtatott fotók és képek letapogatása során. Megjegyzés A beolvasás a szokásosnál hosszabb ideig tart, ha engedélyezi a Moire minták csökkentése (Reduce moire) funkciót.
(2) Mentési beállítások terület • Fájlnév (File Name) Írja be a menteni kívánt kép fájlnevét. Fájl mentésekor a megadott fájlnévhez a dátum és 4 számjegy lesz hozzáfűzve „_20XX0101_0001” formátumban. • Adatformátum (Data Format) Megadja a beolvasott képek mentésekor használt adatformátumot. A választható lehetőségek: JPEG/Exif, TIFF, PNG, PDF vagy PDF (több oldal) (PDF (Multiple Pages)).
• Optikai szövegfelismerés indítása (Start OCR) Válassza ezt a lehetőséget, ha a képen lévő szöveget a megadott OCR szoftverrel szöveges adattá szeretné alakítani. Az alkalmazást a legördülő menüből választhatja ki. • Ne indítson el alkalmazást (Do not start any application) A képeket a Mentés ide (Save in) beállításnál megadott mappába menti. Megjegyzés Adja meg az alkalmazást vagy a mappát a legördülő menü Hozzáadás... (Add...
A Beállítások (Egyéni beolvasás) párbeszédpanel A Beállítások (Egyéni beolvasás) (Settings (Custom Scan)) párbeszédpanel megjelenítéséhez a (Beolvasás számítógépről) lapon kattintson az Egyéni beolvasás (Custom Scan) elemre. A Beállítások (Egyéni beolvasás) (Settings (Custom Scan)) párbeszédpanelen speciális beolvasási beállításokat adhat meg az egyéni igényei szerinti beolvasáshoz.
A 2L méretnél (127 x 178 mm) (5 x 7 hüvelyk) kisebb szöveges dokumentumok, például a puhafedelű regények a gerinc kivágásával Vékony fehér papírra nyomtatott anyagok Hosszú, keskeny anyagok, például panorámafotók Tükröződő lemezcímkék beolvasása nem biztos, hogy a vártnak megfelelő lesz. Helyezze el megfelelően az anyagokat a beolvasni kívánt anyag típusa szerint. Máskülönben lehet, hogy az anyagok beolvasása nem lesz megfelelő.
Ez akkor jelenik meg, amikor az ADF vagy az Automatikus (Auto) lehetőséget választja a Forrás kiválasztása (Select Source) beállításnál. Kattintson erre a gombra a Dokum.beolvasás tájolási beállításai (Document Scan Orientation Settings) párbeszédpanel megnyitásához, amelyen megadhatja az ADF használatával beolvasandó dokumentumok tájolását és kötési oldalát. Fontos A Kötési oldal (Binding Side) nem adható meg, ha csak a dokumentumok elülső oldalának beolvasása van beállítva.
• Ajánlott képjavítások alkalmazása (Apply recommended image correction) Automatikusan alkalmazza az anyag típusának megfelelő javításokat. Fontos A javítások miatt a kép színtónusa eltérhet az eredetitől. Ebben az esetben törölje a négyzet jelölését, és hajtsa végre a letapogatást. Megjegyzés A letapogatás a szokásosnál hosszabb ideig tart, ha engedélyezi ezt a funkciót.
Gerincárnyék-korrekcióra a ScanGear (lapolvasó illesztőprogram) Különleges mód (Advanced Mode) lapját használja, ha nem szabványos méretű anyagokat vagy egyénileg megadott területeket olvas be. További részleteket az Online kézikönyv kezdőlapján található, az adott típusra vonatkozó „Gerincárnyék-korrekció” című részben talál. • Ferde szöveges dokumentumok javítása (Correct slanted text document) Észleli és javítja a dokumentum beolvasott szövegének szögét (-0,1 – -10 fok vagy +0,1 – +10 fok tartományban).
Nem választhatja a JPEG/Exif formátumot, ha a Színmód (Color Mode) beállítás értéke Fekete-fehér (Black and White). Ha az Alkalmazás-beállítások (Application Settings) értéke Optikai szövegfelismerés indítása (Start OCR), nem választhatja ki a PDF, a PDF (több oldal) (PDF (Multiple Pages)) vagy az Automatikus (Auto) beállítást. Megjegyzés Az Automatikus (Auto) lehetőség csak akkor jelenik meg, ha az Automatikus (Auto) értéket választja a Forrás kiválasztása (Select Source) beállításnál. • Beáll.-ok...
Megjegyzés Adja meg az alkalmazást vagy a mappát a legördülő menü Hozzáadás... (Add...) elemének választásával megjeleníthető Alkalmazás választása (Select Application) vagy Célmappa választása (Select Destination Folder) párbeszédpanelen. • Utasítások (Instructions) Megnyitja ezt a kézikönyvet. • Alapértelmezés (Defaults) A megjelenített képernyőn visszaállíthatja a beállítások alapértelmezett értékét.
A Beállítások (Beolvasás és egyesítés) párbeszédpanel A Beállítások (Beolvasás és egyesítés) (Settings (Scan and Stitch)) párbeszédpanel megjelenítéséhez a (Beolvasás számítógépről) lapon kattintson az Beolvasás és egyesítés (Scan and Stitch) elemre. A Beállítások (Beolvasás és egyesítés) (Settings (Scan and Stitch)) párbeszédpanelen speciális beolvasási beállításokat adhat meg az üveglapnál nagyobb anyagok beolvasásához.
• Képfeldolgozás beállításai (Image Processing Settings) A következők beállításához kattintson a (plusz) gombra. Az elérhető beállítási lehetőségek a Forrás kiválasztása (Select Source) értékétől függenek. Fontos A Képfeldolgozás beállításai (Image Processing Settings) nem használható, ha a Színmód (Color Mode) értéke Fekete-fehér (Black and White). Ha a Forrás kiválasztása (Select Source) értéke Fénykép (Photo) • Körvonal élesítése (Sharpen outline) Kiemeli az elemek körvonalát, így élesíti a képet.
• Beolvasási eredmények ellenőrzése (Check scan results) Beolvasás után megjeleníti a Beállítások mentése (Save Settings) párbeszédpanelt. A Beállítások mentése párbeszédpanel Fontos Amikor a Beállítások párbeszédpanelt a My Image Garden szolgáltatásból jeleníti meg, ez a lehetőség nem jelenik meg. (3) Alkalmazás-beállítások terület • Megnyitás egy alkalmazással (Open with an application) Válassza ezt a lehetőséget a beolvasott képek helyesbítéséhez vagy javításához.
A Beállítások (ScanGear) párbeszédpanel A Beállítások (ScanGear) (Settings (ScanGear)) párbeszédpanel megjelenítéséhez a számítógépről) lapon kattintson a ScanGear elemre. (Beolvasás A Beállítások (ScanGear) (Settings (ScanGear)) párbeszédpanelen megadhatja a képek mentési beállításait a ScanGear (lapolvasó illesztőprogram) használatával beolvasott anyagokhoz, valamint azt, hogy mi történjen a mentésük után.
kulcsszavas keresését és tömörítési típusát, illetve kiválaszthatja az automatikus módban beolvasott képek mentéséhez használandó adatformátumot. Az Adatformátum-beállítások párbeszédpanel • Mentés ide (Save in) Megjeleníti azt a mappát, ahová a letapogatott képek mentésre kerülnek. Másik mappa megadásához a legördülő menü Hozzáadás... (Add...) elemének választásával megjeleníthető Célmappa választása (Select Destination Folder) párbeszédpanelen válassza ki a kívánt mappát.
A képeket a Mentés ide (Save in) beállításnál megadott mappába menti. Megjegyzés Adja meg az alkalmazást vagy a mappát a legördülő menü Hozzáadás... (Add...) elemének választásával megjeleníthető Alkalmazás választása (Select Application) vagy Célmappa választása (Select Destination Folder) párbeszédpanelen. • Utasítások (Instructions) Megnyitja ezt a kézikönyvet. • Alapértelmezés (Defaults) A megjelenített képernyőn visszaállíthatja a beállítások alapértelmezett értékét.
A Beállítások (Mentés számítógépre (automatikus)) párbeszédpanel A Beállítások (Mentés számítógépre (automatikus)) (Settings (Save to PC (Auto))) párbeszédpanel megjelenítéséhez kattintson a Mentés számítógépre (automatikus) (Save to PC (Auto)) gombra a (Beolvasás a kezelőpanel használatával) lapon.
(2) Mentési beállítások terület • Fájlnév (File Name) Írja be a menteni kívánt kép fájlnevét. Fájl mentésekor a megadott fájlnévhez a dátum és 4 számjegy lesz hozzáfűzve „_20XX0101_0001” formátumban. • Adatformátum (Data Format) Az Automatikus (Auto) lehetőséget választja. A következő adatformátumokat a program automatikusan használja mentéskor a dokumentumtípus alapján.
A Beállítások (Mentés számítógépre (fénykép)) párbeszédpanel A Beállítások (Mentés számítógépre (fénykép)) (Settings (Save to PC (Photo))) párbeszédpanel megjelenítéséhez kattintson a Mentés számítógépre (fénykép) (Save to PC (Photo)) gombra a (Beolvasás a kezelőpanel használatával) lapon. A Beállítások (Mentés számítógépre (fénykép)) (Settings (Save to PC (Photo))) párbeszédpanelen megadhatja, hogy mi történjen, amikor a kezelőpanelről történő beolvasás után fényképként menti a képeket a számítógépre.
Az Adatformátum-beállítások párbeszédpanel • Mentés ide (Save in) Megjeleníti azt a mappát, ahová a letapogatott képek mentésre kerülnek. Másik mappa megadásához a legördülő menü Hozzáadás... (Add...) elemének választásával megjeleníthető Célmappa választása (Select Destination Folder) párbeszédpanelen válassza ki a kívánt mappát. Az alapértelmezett mentési mappák a következők.
A Beállítások (Mentés számítógépre (dokumentum)) párbeszédpanel A Beállítások (Mentés számítógépre (dokumentum)) (Settings (Save to PC (Document))) párbeszédpanel megjelenítéséhez kattintson a Mentés számítógépre (dokumentum) (Save to PC (Document)) gombra a (Beolvasás a kezelőpanel használatával) lapon.
A javítások miatt a kép színtónusa eltérhet az eredetitől. Ebben az esetben törölje a négyzet jelölését, és hajtsa végre a letapogatást. Megjegyzés A letapogatás a szokásosnál hosszabb ideig tart, ha engedélyezi ezt a funkciót. • Gerincárnyék csökkentése (üveglap) (Reduce gutter shadow (platen)) Csökkenti a gerincárnyékok, amely a nyitott könyvek beolvasásakor a lapok között jelenik meg. Fontos Ez a funkció csak akkor használható, ha az üveglapot használja a beolvasáshoz.
Az Adatformátum-beállítások párbeszédpanel • Mentés ide (Save in) Megjeleníti azt a mappát, ahová a letapogatott képek mentésre kerülnek. Másik mappa megadásához a legördülő menü Hozzáadás... (Add...) elemének választásával megjeleníthető Célmappa választása (Select Destination Folder) párbeszédpanelen válassza ki a kívánt mappát. Az alapértelmezett mentési mappák a következők.
A Beállítások (Csatolás e-mailhez (fénykép)) párbeszédpanel A Beállítások (Csatolás e-mailhez (fénykép)) (Settings (Attach to E-mail (Photo))) párbeszédpanel megjelenítéséhez kattintson a Csatolás e-mailhez (fénykép) (Attach to E-mail (Photo)) gombra a (Beolvasás a kezelőpanel használatával) lapon.
Az Adatformátum-beállítások párbeszédpanel • Mentés ide (Save in) Megjeleníti azt a mappát, ahová a letapogatott képek mentésre kerülnek. Másik mappa megadásához a legördülő menü Hozzáadás... (Add...) elemének választásával megjeleníthető Célmappa választása (Select Destination Folder) párbeszédpanelen válassza ki a kívánt mappát. Az alapértelmezett mentési mappák a következők.
A Beállítások (Csatolás e-mailhez (dokumentum)) párbeszédpanel A Beállítások (Csatolás e-mailhez (dokumentum)) (Settings (Attach to E-mail (Document))) párbeszédpanel megjelenítéséhez kattintson a Csatolás e-mailhez (dokumentum) (Attach to E-mail (Document)) gombra a (Beolvasás a kezelőpanel használatával) lapon.
Megjegyzés A letapogatás a szokásosnál hosszabb ideig tart, ha engedélyezi ezt a funkciót. • Gerincárnyék csökkentése (üveglap) (Reduce gutter shadow (platen)) Csökkenti a gerincárnyékok, amely a nyitott könyvek beolvasásakor a lapok között jelenik meg. Fontos Ez a funkció csak akkor használható, ha az üveglapot használja a beolvasáshoz. Csak akkor érhető el, ha a Beolvasott képek tömörítése továbbításkor (Compress scanned images upon transfer) jelölőnégyzet nincs bejelölve.
Megjeleníti azt a mappát, ahová a letapogatott képek mentésre kerülnek. A mappa módosításához kattintson a Hozzáadás... (Add...) gombra, majd adja meg a célmappát a Célmappa választása (Select Destination Folder) párbeszédpanelen. Az alapértelmezett mentési mappák a következők.
A Beállítások (Általános beállítások) párbeszédpanel A Beállítások (Általános beállítások) (Settings (General Settings)) párbeszédpanel megjelenítéséhez kattintson az (Általános beállítások) lapra. A Beállítások (Általános beállítások) (Settings (General Settings)) párbeszédpanelen megadhatja a használt terméket, az e-mail mellékletek fájlméretére vonatkozó korlátozást, a képek lévő szöveg felismeréséhez használt nyelvet, valamint a képek ideiglenes tárolásához használt mappát.
• Alapértelmezés (Defaults) A megjelenített képernyőn visszaállíthatja a beállítások alapértelmezett értékét.
Az Adatformátum-beállítások párbeszédpanel Az Adatformátum-beállítások (Data Format Settings) párbeszédpanelt a következő műveletek valamelyikének végrehajtásával jelenítheti meg. • A Beállítások párbeszédpanel lapjain a Beállítások mentése (Save Settings) elemhez tartozó Beállítások... (Settings...) elemre kattinthat.
Megadhatja az automatikus beolvasás közben dokumentumként felismert eredeti példányok automatikus mentéséhez használandó adatformátumot. • Az automatikus beolvasáskor fényképként felismert elemek formátuma (Format for Item Detected as Photo in Auto Scan) Megadhatja az automatikus beolvasás közben fényképként felismert eredeti példányok automatikus mentéséhez használandó adatformátumot. • Alapértelmezés (Defaults) A megjelenített képernyőn visszaállíthatja a beállítások alapértelmezett értékét.
A Beállítások mentése párbeszédpanel Ha a beolvasást követően meg szeretné jeleníteni a Beállítások mentése (Save Settings) párbeszédpanelt, jelölje be a Beolvasási eredmények ellenőrzése (Check scan results) jelölőnégyzetet a Beállítások párbeszédpanel Beállítások mentése (Save Settings) részében. A beolvasási eredmények indexképeinek megtekintése közben megadhatja az adatformátumot és a célt.
• Adatformátum (Data Format) Megadja a beolvasott képek mentésekor használt adatformátumot. A választható lehetőségek: JPEG/Exif, TIFF, PNG, PDF vagy PDF (több oldal) (PDF (Multiple Pages)). Fontos A PDF vagy a PDF (több oldal) (PDF (Multiple Pages)) beállítás nem választható a következő esetekben. Amikor úgy hajtotta végre a beolvasást, hogy a Fénykép (Photo) elemre kattintott az IJ Scan Utility főképernyőjén.
A Képek egyesítése ablak A Képek egyesítése (Image Stitch) ablak megjelenítéséhez az IJ Scan Utility főképernyőjén kattintson az Egyesítés (Stitch) elemre. A nagyméretű dokumentumok jobb és bal oldali felét beolvashatja külön-külön, majd összefűzheti a két részt egy képpé. Az üveglapnál legfeljebb körülbelül kétszer nagyobb anyagok olvashatók le.
• 1-es beolvasott kép (Scan Image 1) • 1-es kép beolvasásának elindítása (Start Scanning Image 1) Beolvassa az első részt. • 2-es beolvasott kép (Scan Image 2) • 2-es kép beolvasásának elindítása (Start Scanning Image 2) Beolvassa a második részt. • Vágási keretek beállítása (Adjust cropping frames) A megtekintési területen beállíthatja a beolvasási területet. Ha nincs megadva a terület, a program a Kimeneti méret megadása (Select Output Size) beállításnál megadott méretű képet fog létrehozni.
Megszakítja az Egyesítés (Stitch) beállítással végrehajtott beolvasást. (2) Eszköztár • Eszköztár Törölheti a beolvasott képeket vagy módosíthatja az előzetesen megtekintett képeket. • (Törlés) Törli a beolvasott képet. • (Nagyítás/kicsinyítés) Nagyíthatja vagy kicsinyítheti az előnézeti képet. A megjelenített kép nagyításához kattintson az egér bal gombjával a megtekintési területre. A megjelenített kép kicsinyítéséhez kattintson az egér jobb gombjával a megtekintési területre.
• Az 1-es kép beolvasásának elindítása (Start Scanning Image 1) elemre kattintva beolvasott első rész A lapolvasó beolvassa a képet a Beolvasási irány (Scan Direction) beállításnál megadott irányban, és a 2 számot jeleníti meg mellette. • A 2-es kép beolvasásának elindítása (Start Scanning Image 2) elemre kattintva beolvasott második rész Megjelenik a két beolvasott kép.
Beolvasás a használt szoftveralkalmazással (ScanGear) Mi a ScanGear (Lapolvasó illesztőprogram)? Beolvasás a ScanGear (Lapolvasó illesztőprogram) speciális beállításaival A ScanGear (Lapolvasó illesztőprogram) indítása Letapogatás Alap módban Letapogatás Különleges módban Több dokumentum letapogatása az ADF-ből (Automatikus lapadagoló) Különleges módban Több dokumentum egyidejű letapogatása a ScanGear (Lapolvasó illesztőprogram) alkalmazással Képek javítása és a színek beállítása a ScanGear (Lapolvasó illes
5. Állítsa be a Kimeneti beállítások (Output Settings) értékét. Kimeneti beállítások 6. Szükség szerint állítsa be a vágási keretet (letapogatási területet), javítsa a képet vagy állítsa be a színeket. Vágási keretek beállítása (ScanGear) Kép beállításai Színbeállítás gombok 7. Kattintson a Letapogatás (Scan) gombra. Ezzel a letapogatás elindul.
Több dokumentum letapogatása az ADF-ből (Automatikus lapadagoló) Különleges módban A Különleges mód (Advanced Mode) lapon megadhatja a képek világosságát, színtónusát stb., és a dokumentumokat az ADF-be (automatikus lapadagoló) helyezve egyidejűleg beolvashatja őket. Auto kétoldalas ADF-fel rendelkező modellek használatakor a dokumentumok mindkét oldala automatikusan beolvasható az ADF-ből. Ha a beolvasást az ADF-ből végzi, akkor a dokumentumok beolvasása előnézet nélkül történik. 1.
5. Végezze el a kívánt képkorrekciókat és színigazításokat. Kép beállításai Színbeállítás gombok 6. Kattintson a Letapogatás (Scan) gombra. Ezzel a letapogatás elindul. Megjegyzés Kattintson ide (Információ), ha meg szeretne nyitni egy párbeszédpanelt, ahol ellenőrizni tudja a jelenlegi letapogatási beállításokat (dokumentum típusa stb.).
Több dokumentum egyidejű letapogatása a ScanGear (Lapolvasó illesztőprogram) alkalmazással Az Alap mód (Basic Mode) és Különleges mód (Advanced Mode) lapon egyszerre beolvashatja az üveglapra helyezett két vagy több fotót (kis dokumentumot). Ebben a részben elmagyarázzuk, hogyan lehet letapogatni több dokumentumot az Alap mód (Basic Mode) lapon. Fontos Ha több dokumentumot szeretne beolvasni egyetlen képként, a letapogatást teljes kép nézetben hajtsa végre.
A megtekintési területen megjelennek a képek indexképei. A vágási keretek meghatározása automatikusan történik a dokumentum méretének megfelelően. 4. Állítsa be a Cél (Destination) értékét. 5. A célnak megfelelően határozza meg a Kimeneti méret (Output Size) beállítást. 6. Állítsa be a vágási kereteket, és adja meg szükség szerint a Képkorrekciók (Image corrections) beállításokat. Megjegyzés A képek javítását egymástól függetlenül is elvégezheti.
Megjegyzés Ha a teljes kép van megjelenítve, az ikon (Teljes kép) alakúra változik. 2. Állítsa be a Cél (Destination) értékét. 3. A célnak megfelelően határozza meg a Kimeneti méret (Output Size) beállítást. Az Oldalarány felcserélése (Invert aspect ratio) funkció akkor áll rendelkezésre, ha a Kimeneti méret (Output Size) nem Rugalmas (Flexible) értékű. Kattintson erre a gombra a vágási keret elforgatásához. Kattintson újra az eredeti tájolás visszaállításához. 4. Állítsa be a vágási kereteket.
Képek javítása és a színek beállítása a ScanGear (Lapolvasó illesztőprogram) segítségével Rosszul fókuszált fényképek élesítése, por és karcolások csökkentése, halvány színek javítása Képek javítása (Élesítő maszk, Por és karcolások csökkentése, Halványulási korrekció stb.
Képek javítása (Élesítő maszk, Por és karcolások csökkentése, Halványulási korrekció stb.) A ScanGear (lapolvasó illesztőprogram) Különleges mód (Advanced Mode) lapjának Kép beállításai (Image Settings) funkciói képek beolvasásakor a tárgyak körvonalának kiemelését, a foltok, karcolások csökkentését és a halvány színek javítását teszik lehetővé. Beállítási lehetőségek Kattintson az eszközhöz tartozó nyílra, és válasszon egy elemet a legördülő menüről.
A szövegdokumentumok átlátszóságának csökkentése, illetve az újrahaszonosított papír, újságpapír stb. alapszínének világosítása dokumentumok szkennelésekor Állítsa az Átnéző csökkentése (Reduce Show-through) beállítást BE (ON) értékre. KI (OFF) BE (ON) Rosszul fókuszált képek élesítése Állítsa az Élesítő maszk (Unsharp Mask) értékét BE (ON) állásra. KI (OFF) BE (ON) Átmenetek és vonalas minták csökkentése Állítsa a Rácshiba eltávolítása (Descreen) értékét BE (ON) állásra.
Nincs (None) Közepes (Medium) Azon fotók javítása, melyek az idővel kifakultak vagy túlszínezettségük van Állítsa a Halványulási korrekció (Fading Correction) lehetőséget Kicsi (Low), Közepes (Medium) vagy Nagy (High) értékre a fakulás vagy túlszínezettség mértékének megfelelően. Nincs (None) Közepes (Medium) Szemcsék csökkentése Állítsa a Szemcsekorrekció (Grain Correction) lehetőséget Kicsi (Low), Közepes (Medium) vagy Nagy (High) értékre a szemcsézettség mértékének megfelelően.
Színek beállítása a színmintázat segítségével A ScanGear (lapolvasó illesztőprogram) Alap mód (Basic Mode) lapjának színmintázat funkciójával előzetesen megtekintheti a színek módosítását, és visszaadhatja a természetes színeket. Színigazítás Javítja azokat a színeket, melyek az idővel kifakultak vagy túlszínezettségük van. „Túlszínezettség” esetén egy adott szín meghatározza az egész kép színvilágát az időjárás vagy erős környezeti színek miatt.
Az alábbi példa egy kékes kép javítását mutatja. Mivel a Kék (Blue) és a Zöld (Green) színek túl erősek, javításukhoz kattintson a Sárga (Yellow) és a Bíbor (Magenta) nyilakra. Előtte Utána Megjegyzés A színbeállítások csak a vágási keretekre (beolvasási területekre) vagy az indexkép nézetben kiválasztott képkockára vonatkoznak. Több képkockát vagy vágási keretet is kiválaszthat, ha a Ctrl billentyű lenyomása közben kattint rájuk.
A telítettség és a színegyensúly beállítása Kattintson a ScanGear (lapolvasó illesztőprogram) Különleges mód (Advanced Mode) lapján a (Telítettség/Színegyensúly) gombra. Megjegyzés Az aktuális ablak összes beállításának visszaállításához kattintson az Alapért. (Defaults) pontra. Telítettség Állítsa be a kép telítettségét (élénkség). Fényesítheti azokat a színeket, melyek az idővel kifakultak stb.
Általában egyetlen színpár állításával nehéz teljesen kijavítani a képet. Azt ajánljuk, hogy próbáljon a képen egy olyan részt találni, melynek fehérnek kellene lenni, és állítsa be úgy mindhárom színpárt, hogy az a rész fehér legyen. Értékeket is megadhat (-127-től 127-ig). Az alábbi példában egy olyan kép látható, amelynél a „Ciánkék és a Piros” színpár volt állítva.
A fényesség és a kontraszt beállítása Kattintson a ScanGear (lapolvasó illesztőprogram) Különleges mód (Advanced Mode) lapján a (Fényesség/Kontraszt) ikonra. Megjegyzés A részletes nézetre történő váltáshoz kattintson a (Le) nyílra. Az előző nézetre való visszatéréshez kattintson a (Fel) nyílra. Az aktuális ablak összes beállításának visszaállításához kattintson az Alapért. (Defaults) pontra. Csatorna A kép minden pontja a piros, a zöld és a kék adott arányú (gradiens) keveréke.
Fényesség csúszkát a Fényesség (Brightness) alatt balra a kép A kép világosságát állítja be. Mozgassa a sötétítéséhez, jobbra pedig a világosításához. Értékeket is megadhat (-127-től 127-ig). Sötétített Eredeti kép Világosított Megjegyzés A fényes részek elveszhetnek, ha túlzottan világosítja a képet, illetve az árnyas részek elveszhetnek, ha ha túlzottan sötétíti a képet. Kontraszt A kontraszt a kép világosabb és sötétebb részei közötti eltérés mértéke.
A hisztogram beállítása Kattintson a ScanGear (lapolvasó illesztőprogram) Különleges mód (Advanced Mode) lapján a (Hisztogram) gombra. Megjegyzés Az aktuális ablak összes beállításának visszaállításához kattintson az Alapért. (Defaults) pontra. Csatorna A kép minden pontja a piros, a zöld és a kék adott arányú (gradiens) keveréke. Ezek a színek egyenként, „csatornaként” állíthatók. • Mester (Master) A piros, a zöld és a kék színt együtt állítja be. • Piros (Red) A Piros csatornát állítja be.
Több adat oszlik meg a világos részen. Több adat oszlik meg az árnyas részen. Az adatok széles tartományban oszlanak meg a világos és a sötétebb részek között. Hisztogramok beállítása (A csúszka használata) Válasszon ki egy Csatorna (Channel) opciót, majd állítsa be az árnyék és a világos részek szintjét a (Fekete-pont) csúszka, illetve a (Fehér-pont) csúszka mozgatásával. - Minden rész, amely balra van a (Fekete pont) csúszkától, fekete lesz (0. szint).
Képek több megoszló adattal a világos részen Mozgassa a középpont csúszkát a világos oldal felé. Képek több megoszló adattal az árnyas részen Mozgassa a középpont csúszkát az árnyas oldal felé. Hisztogramok beállítása (A csepegtetők használata) Amikor kiválaszt egy Csatorna (Channel) lehetőséget és rákattint a fekete-pont, közép-pont vagy a fehérpont csepegtetőre, az egérmutató a megtekintési képen átalakul egy csepegtetővé. A beállítások módosításához kattintson az alábbi csepegtetőkkel a hisztogramra.
A tónusgörbe beállítása Kattintson a ScanGear (lapolvasó illesztőprogram) Különleges mód (Advanced Mode) lapján a (Tónusgörbe-beállítások) ikonra. Megjegyzés Az aktuális ablak összes beállításának visszaállításához kattintson az Alapért. (Defaults) pontra. Csatorna A kép minden pontja a piros, a zöld és a kék adott arányú (gradiens) keveréke. Ezek a színek egyenként, „csatornaként” állíthatók. • Mester (Master) A piros, a zöld és a kék színt együtt állítja be. • Piros (Red) A Piros csatornát állítja be.
A tónusgörbe beállítása A Tónusgörbe kiválasztása (Select Tone Curve) listában válasszon egy tónusgörbét a Nincs korrekció (No correction), Túlexponált (Overexposure), Alulexponált (Underexposure), Nagy kontraszt (High contrast), Negatív/pozitív filmek megfordítása (Reverse the negative/positive image) és az Egyéni görbe szerkesztése (Edit custom curve) lehetőségek közül.
Egyéni görbe szerkesztése (Edit custom curve) Megfoghatja a Tónusgörbe bizonyos pontjait, mellyel szabadon állíthatja a megfelelő terület fényességét.
A küszöb beállítása A színes és szürkeárnyalatos képeken a fényesség egy 0 és 255 közötti értékkel van kifejezve. Feketefehér kép létrehozásakor azonban a színek fekete (0) vagy fehér (255) színre vannak leképezve. A küszöb egy határvonal, amely egy színt feketének vagy fehérnek határoz meg. A küszöb szintjének állításával szöveges dokumentumban élesítheti a szöveget, vagy csökkentheti az átütés hatását újságoknál.
A ScanGear (Lapolvasó illesztőprogram) képernyői Alap mód lap Különleges mód lap Bemeneti beállítások Kimeneti beállítások Kép beállításai Színbeállítás gombok Beállítások párbeszédpanel Lapolvasó lap Megtekintés lap Letapogatás lap Színbeállítások lap 120
Alap mód lap Ezen mód segítségével a képernyőn megjelenő lépéseket követve könnyedén elvégezheti a letapogatást. Ez a szakasz az Alap mód (Basic Mode) lapon elérhető beállításokat és funkciókat írja le. Ha a beolvasást az ADF-ből (automatikus lapadagoló) végzi, akkor a dokumentumok beolvasása előnézet nélkül történik. (1) Beállítások és műveleti gombok (2) Eszköztár (3) Megtekintési terület Megjegyzés A megjelenített elemek a dokumentum típusától és a nézettől függnek.
Fontos Bizonyos alkalmazások nem támogatják az ADF-ből történő folytonos beolvasást. Részleteket az alkalmazás kézikönyvében talál. Megjegyzés Amikor kiválaszt egy dokumentumtípust, bekapcsol az élesítő maszk funkció. Ha az ADF-típusoktól eltérő beállítást választ, a dokumentum típusának megfelelő képjavító funkció is engedélyezve lesz. Ha a Magazin (Színes) (Magazine (Color)) lehetőséget választja, a rácshiba eltávolítása funkció aktív lesz.
Teljes kép nézetben Ha nincs vágási keret, a teljes megtekintési terület le lesz tapogatva. Ha a vágási keret meg van jelenítve, a képnek csak a kereten belüli része lesz letapogatva. • Papírméret (L, A4 stb.) Válasszon ki egy kimeneti papírméretet. A képnek a vágási kereten belüli része lesz a kiválasztott papírméretben letapogatva. Megfoghatja a vágási keretet, s az oldalarány megtartásával nagyíthatja, kicsinyítheti azt. • Képernyőméret (1024 x 768 képpont stb.
• Vágási keretek beállítása (Adjust cropping frames) A megtekintési területen lehet beállítani a letapogatási területet. Ha nincs terület megadva, a dokumentum a dokumentumméret szerint lesz letapogatva (Automatikus vágás). Ha ki van választva egy terület, a képnek csak a vágási kereten belüli része lesz letapogatva. Vágási keretek beállítása (ScanGear) • Képkorrekciók (Image corrections) A segítségével korrekciókat alkalmazhat a képeken.
(2) Eszköztár • Eszköztár Módosíthatja és forgatja a megtekintési képeket. Az eszköztár megjelenített gombjai a nézettől függnek. Indexkép nézetben Teljes kép nézetben • (Indexkép) / (Teljes kép) Átváltja a megtekintési terület nézetét. Megtekintési terület • (Forgatás balra) A megtekintési képet 90 fokkal elfordítja az óramutató járásával ellenkező irányban. - Az eredmény tükröződik majd a letapogatott képen. - A kép visszatér az eredeti állapotába, amikor újra megtekinti a képet.
• (Útmutató megnyitása) Megnyitja ezt az oldalt. (3) Megtekintési terület • Megtekintési terület Ez az a terület, ahol egy próbakép megjelenik a Megtekintés (Preview) gombra kattintva. Itt ellenőrizheti a „Beállítások és műveleti gombok” részben ismertetett beállítások (képkorrekciók, színigazítások stb.) eredményét is. Ha az (Indexkép) gomb látható az eszköztáron A vágási keretek a dokumentum mérete szerint vannak beállítva, és a beolvasott képek indexképe látható.
Megjegyzés Megadhatja a vágási keretet a megjelenített képen. Az indexkép nézetben képenként csak egy vágási keretet lehet megadni. A teljes kép nézetben több vágási keret is megadható.
Különleges mód lap Lehetővé teszi olyan speciális beállítások megadását, mint a színmód, a kimeneti felbontás, a kép fényessége és a színtónus. Ez a szakasz a Különleges mód (Advanced Mode) lapon elérhető beállításokat és funkciókat írja le. Ha a beolvasást az ADF-ből (automatikus lapadagoló) végzi, akkor a dokumentumok beolvasása előnézet nélkül történik.
A Kedvenc beállítások listája (Favorite Settings List) egy elemének törléséhez válassza azt ki, majd kattintson a Törlés (Delete) gombra. Kattintson a Mentés (Save) gombra a Kedvenc beállítások listája (Favorite Settings List) által mutatott beállítások elmentéséhez. Megjegyzés Használhatja a Hozzáadás/törlés... (Add/Delete...) elemet a Kedvenc beállítások (Favorite Settings) panelen a megtekintés után. Legfeljebb 10 elem menthető el.
• Letapogatás (Scan) A beolvasás elkezdése. Megjegyzés Miután a letapogatás elkezdődött, a program jelzi annak előrehaladását. Kattintson a Mégse (Cancel) gombra a letapogatás megszakításához. Ha a letapogatás befejeződött, egy párbeszédpanel jelenik meg, melyben kiválaszthatja a következő műveletet. Kövesse a felszólításokat a befejezéshez.
Átváltja a megtekintési terület nézetét. Megtekintési terület • (Törlés) Törli a megtekintési képet a Megtekintés területről. Az eszköztárat és a színbeállításokat is visszaállítja. • (Vágás) Lehetővé teszi a letapogatási terület egérrel való kijelölését. • (Kép mozgatása) Lehetővé teszi a kép húzását, amíg a kívánt rész meg nem jelenik, ha a Megtekintés területen látható nagyított kép nem fér el a képernyőn. A képet a gördítősávokkal is mozgathatja.
• (Útmutató megnyitása) Megnyitja ezt az oldalt. (3) Megtekintési terület • Megtekintési terület Ez az a terület, ahol egy próbakép megjelenik a Megtekintés (Preview) gombra kattintva. Itt ellenőrizheti a „Beállítások és műveleti gombok” részben ismertetett beállítások (képkorrekciók, színigazítások stb.) eredményét is. Ha az (Indexkép) gomb látható az eszköztáron A vágási keretek a dokumentum mérete szerint vannak beállítva, és a beolvasott képek indexképe látható.
Megjegyzés Megadhatja a vágási keretet a megjelenített képen. Az indexkép nézetben képenként csak egy vágási keretet lehet megadni. A teljes kép nézetben több vágási keret is megadható.
Bemeneti beállítások A Bemeneti beállítások (Input Settings) segítségével állíthatja be a következő elemeket: • Forrás kiválasztása (Select Source) Megjelenik a letapogatni kívánt dokumentum típusa. A tálcáról történő beolvasáshoz válassza a Tálca (Platen) lehetőséget; ADF (automatikus lapadagoló) használatakor válassza a Dokum. (ADF egyoldalas) (Document (ADF Simplex)) vagy a Dokum. (ADF kétoldalas) (Document (ADF Duplex)) értéket.
Fontos A Tájolás (Orientation) párbeszédpanel csak akkor nyitható meg, ha a Forrás kiválasztása (Select Source) értéke Dokum. (ADF egyoldalas) (Document (ADF Simplex)) vagy Dokum. (ADF kétoldalas) (Document (ADF Duplex)). A Kötés helye (Binding Location) nem adható meg, ha a Forrás kiválasztása (Select Source) Dokum. (ADF egyoldalas) (Document (ADF Simplex)). • Színmód (Color Mode) Válassza ki a dokumentum letapogatásának módját.
Kimeneti beállítások A Kimeneti beállítások (Output Settings) segítségével állíthatja be a következő elemeket: • Kimeneti felbontás (Output Resolution) Adja meg a letapogatási felbontást. Minél magasabb a felbontás (érték), annál részletesebb a kép. A gombra való kattintással válasszon ki egyet a megjelenített lehetőségek közül, vagy adjon meg egy értéket (1 dpi-s lépésekkel). További részleteket az Online kézikönyv kezdőlapján található, az adott típusra vonatkozó „Felbontás” című részben talál.
Megjegyzés A letapogatott kép nagyításához/kicsinyítéséhez, adja meg a (Szélesség) és (Magasság) értékét a Kimeneti beállítások (Output Settings) panelen, vagy adjon meg értéket (1%-os lépésekben) a % mezőben. Bár a % maximális értéke a Kimeneti felbontás (Output Resolution) értékétől függ, akár 19200 dpi is megadható (a maximális kimeneti felbontás). • Papírméret (L, A4 stb.) és Képernyőméret (1024 x 768 képpont stb.) Nem lehet megadni (szélesség), (magasság) és skálaértéket.
Kattintson erre a gombra a vágási keret elforgatásához. Kattintson újra az eredeti tájolás visszaállításához. • Adatméret (Data Size) A megtekintési kép elmentésekor megjelenik a fájlméret. Megjegyzés Ha a fájlméret meghalad egy meghatározott értéket, az érték piros színnel jelenik meg. Ebben az esetben egy figyelmeztető üzenet jelenik meg, amikor a Letapogatás (Scan) gombra kattint. Ekkor az Adatméret (Data Size) érték csökkentéséhez célszerű módosítani a beállítást.
Kép beállításai Fontos Ezeket a funkciókat ne alkalmazza olyan képekre, melyeken nincsenek moire-minták, foltok/ karcolások vagy halvány színek. A színtónus hátrányosan módosulhat. A képjavítás eredményei esetleg nem látszanak a megtekintési képen. Megjegyzés A választható beállítások a Színmód (Color Mode) beállításaitól függenek. A szkennelés tovább tarthat a megszokottnál a Kép beállításai (Image Settings) használata miatt.
A képjavítási művelet miatt a kép színtónusa eltérhet az eredetitől. Ebben az esetben állítsa a Képjavítás (Image Adjustment) beállítást Nincs (None) értékűre. • Átnéző csökkentése (Reduce Show-through) Használja ezt a funkciót kétoldalas dokumentumok átlátszóságának csökkentésére, illetve az újrahasznosított papír és egyéb színes papírok alapszínének világosítására dokumentumok beolvasásakor. • KI (OFF) Az átütés nem lesz csökkentve.
Megjegyzés Ajánlott, hogy Nincs (None) értékűre állítsa nyomtatványok letapogatásánál. • Halványulási korrekció (Fading Correction) Használja ezt a funkciót idővel megfakult vagy túlszínezett fotók javításához. „Túlszínezettség” esetén egy adott szín meghatározza az egész kép színvilágát az időjárás vagy erős környezeti színek miatt. • Nincs (None) A halványulási korrekció nem lesz alkalmazva. • Kicsi (Low) Válassza ezt a kisebb mértékű fakultság vagy túlszínezés esetén.
Ne helyezzen 2,0 kg (4,4 font) vagy annál nagyobb tömegű tárgyat a tálcára. Ne nyomja továbbá 2,0 kg (4,4 font) meghaladó erővel a dokumentumot. Ha erősen nyomja, akkor lehet, hogy a szkenner nem tud megfelelően működni, illetve betörhet az üveg. Igazítsa a dokumentumot a tálca széléhez. Ha nem így tesz, az árnyék korrigálása nem lesz megfelelő. A dokumentumtól függően az árnyék korrekciója nem biztos, hogy megfelelő lesz.
Színbeállítás gombok A Színbeállítások gombok lehetővé teszik a kép fényerejének és színtónusainak finom javítását, beleértve a kép globális fényerejét/kontrasztját, illetve a fényes és sötét területek beállítását (hisztogram) vagy az egyensúlyt (tónusgörbe). Fontos A színbeállítási gombok nem használhatók, ha a Színegyeztetés (Color Matching) értéket választotta a Beállítások (Preferences) párbeszédpanel Színbeállítások (Color Settings) lapján.
Ellenőrizze a végső színbeállításokat. A következő képfeldolgozásból származó végső szintetikus tónusgörbe és hisztogram jelenik meg. Ezen a képernyőn nincsenek beállítási lehetőségek. • Színes kép esetén a Csatorna (Channel) listában válassza ki, hogy a Piros (Red), a Zöld (Green) és a Kék (Blue) szín közül melyiket ellenőrzi, vagy válassza a Mester (Master) elemet a három szín együttes ellenőrzéséhez.
Legfeljebb 20 elem menthető el. • Alapért. (Defaults) Minden beállítás (telítettség/színegyensúly, fényesség/kontraszt, hisztogram és tónusgörbe) visszaállítása.
Beállítások párbeszédpanel Kattintson a Beállítások... (Preferences...) gombra a ScanGear (szkenner-illesztőprogram) képernyőjén a Beállítások (Preferences) párbeszédablak megnyitásához. A Beállítások (Preferences) párbeszédpanel Lapolvasó (Scanner), Megtekintés (Preview), Letapogatás (Scan) és Színbeállítások (Color Settings) lapján speciális beállításokat adhat meg a ScanGear funkcióihoz.
Lapolvasó lap A Lapolvasó (Scanner) lapon a következő beállításokat adhatja meg. • Csendes beállítások (Quiet Settings) A csendes működés funkciójának segítségével csökkentheti a készülék működési zaját. Használja ezt a zajok csökkentéséhez, ha éjszaka szkennel vagy nyomtat. A csendes mód beállításához kattintson a Beállítások... (Settings...) gombra. Megjegyzés Beállíthatja a csendes módot a készülék kezelőpaneljéről, a nyomtató-illesztőprogramból, illetve a ScanGear programból.
• Hangbeállítások (Sound Settings) Beállíthatja azt, hogy a készülék zenéljen a beolvasás alatt/végén. Válassza ki a Zene letapogatás közben (Play Music During Scanning) vagy a Hangjelzés a letapogatás végén (Play Sound When Scanning is Completed) opciókat, majd kattintson a Tallózás... (Browse...) gombra, és adjon meg egy hangfájlt. Az alábbi fájlokat adhatja meg. - MIDI fájl (*.mid, *.rmi, *.midi) - Audio fájl (*.wav, *.aif, *.aiff) - MP3 fájl (*.
Megtekintés lap A Megtekintés (Preview) lapon a következő beállításokat adhatja meg. • Megtekintés ScanGear indításakor (Preview at Start of ScanGear) Válassza ki, hogyan történjen a megtekintés a ScanGear (lapolvasó illesztőprogram) indulásakor. • Megtekintés automatikus végrehajtása (Automatically Execute Preview) A ScanGear program automatikusan megtekintő üzemmódban indul. • Mentett megtekintési kép megjelenítése (Display Saved Preview Image) Az előzőleg megtekintett kép kerül megjelenítésre.
• Kisebb (Smaller) A normál méret területének 95%-át (szélességben és magasságban) jeleníti meg. Megjegyzés Ha módosítja a Vágási keret a Vázlat nézethez (Cropping Size for Thumbnail View) beállítást, a megtekintési kép frissítve lesz és az új méretre lesz vágva. Mivel frissül a megtekintési kép, a rá alkalmazott szín- és egyéb beállítások vissza lesznek állítva.
Letapogatás lap A Letapogatás (Scan) lapon a következő beállításokat adhatja meg. • A ScanGear párbeszédpanel állapota a letapogatás után (Status of ScanGear dialog after scanning) Állítsa be, hogy mi történjen a ScanGear (lapolvasó illesztő) szoftverrel a képek beolvasása után. • A ScanGear automatikus bezárása (Close ScanGear automatically) Ezt kiválasztva a letapogatás után visszatér az eredeti alkalmazásba.
• Kimenet oldalanként (Output by page) A letapogatott dokumentumok kimenete az oldalsorrend szerint történik.
Színbeállítások lap A Színbeállítások (Color Settings) lapon a következő beállításokat adhatja meg. • Színigazítás Válassza ki a következők egyikét. Akkor választhat ki ilyen beállítást, amikor a Színmód (Color Mode) értéke Színes (Color) vagy Szürkeárnyalatos (Grayscale). • Javasolt (Recommended) Használatával a dokumentum tónusait élénken állíthatja elő a képernyőn. Ajánlott, hogy általában ezt a beállítást használja.
Anyagok elhelyezése (számítógépről történő beolvasás esetén) Tekintse át, hogyan helyezheti az anyagot a lapolvasó vagy nyomtató üveglapjára vagy az ADF-be (az automatikus lapadagolóba). Helyezze el megfelelően az anyagokat a beolvasni kívánt anyag típusa szerint. Máskülönben lehet, hogy az anyagok beolvasása nem lesz megfelelő. Fontos Ne helyezzen tárgyakat a dokumentumfedélre. Amikor kinyitja a dokumentumfedelet, az anyagok beeshetnek a lapolvasóba vagy a nyomtatóba, ami hibás működést okozhat.
dokumentumokat, akkor a beolvasás előtt adja meg a megfelelő adatformátumot. Több anyag elhelyezése Hagyjon 1 cm (0,4 hüvelyk) helyet az anyag és az üveglap szélei (a harántcsíkos rész), valamint az egyes anyagok között. A dokumentumok átlósan vonalazott területen található részeit a készülék nem tudja letapogatni. több, mint 1 cm (0,4 hüvelyk) Megjegyzés Legfeljebb 12 anyagot helyezhet el.
156
Vágási keretek beállítása (ScanGear) A „körbevágás” műveletével kiválaszthatja azt a területet, amelyet beolvasáskor meg szeretne tartani a képből, illetve a maradékot, amelyre nincs szüksége. Az Alap mód (Basic Mode) lapon és a Különleges mód (Advanced Mode) lapon megadhatja a vágási kereteket (beolvasási területeket) a megtekintési területen megjelenített képen. Amikor elindítja a beolvasást, a készülék a vágási keretekkel megadott területeket külön képként olvassa be.
A kurzor (Célkereszt) alakúra változik, ha egy vágási keret belsejébe kerül. Kattintson és húzzon az egérrel a teljes vágási keret mozgatásához. Megjegyzés A Különleges mód (Advanced Mode) lapon megadható a vágási keret mérete a és (Szélesség) (Magasság) értékének magadásával a Bemeneti beállítások (Input Settings) elemeinél. Bemeneti beállítások Elforgathat egy vágási keretet 90 fokkal az (Oldalarány váltása) gombra kattintva.
Létrehozhat több vágási keretet, amelyekre különböző letapogatási beállításokat adhat meg. Több vágási keretet is kiválaszthat, ha a Ctrl billentyű lenyomása közben kattint rájuk. Ha több vágási keretet választ ki és a ScanGear program jobb oldali részén lévő lapon módosítja az értékeiket, akkor az összes kiválasztott vágási keret ugyanazokat a módosított értékeket veszi fel. Ha felvesz egy új keretet, az megtartja az előző vágási keret értékeit. Megjegyzés Legfeljebb 12 vágási keret hozható létre.
Általános megjegyzések (Lapolvasó illesztőprogram) A ScanGear lapolvasó illesztőprogramra a következő korlátozások vonatkoznak. Használatakor ügyeljen ezekre. Lapolvasó illesztőprogram korlátozásai • NTFS fájlrendszer esetén a TWAIN-adatforrás lehet, hogy nem indítható el. Ez azért van, mert biztonsági okokból nem lehet a TWAIN modult a winnt mappába írni. Segítségért forduljon a rendszergazdához.
• Némely alkalmazásban lehet, hogy nem megfelelően lesznek letapogatva a képek. Ebben az esetben növelje meg az operációs rendszer virtuális memóriáját, majd próbálja meg újra. • Ha a képméret túl nagy (mint például nagy képek magas felbontás mellett történő letapogatásakor), előfordulhat, hogy a számítógép nem válaszol, vagy az alkalmazástól függően az állapotjelző sáv 0%on marad.
Hasznos információk letapogatáshoz Vágási keretek beállítása (IJ Scan Utility) Felbontás Adatformátumok Színegyeztetés 162
Vágási keretek beállítása (IJ Scan Utility) A „körbevágás” műveletével kiválaszthatja azt a területet, amelyet beolvasáskor meg szeretne tartani a képből, illetve a maradékot, amelyre nincs szüksége. A Képek egyesítése (Image Stitch) ablakban megadhatja a megtekintési területen megjelenített kép vágási keretét.
Felbontás A letapogatott képben lévő adat nem más, mint képpontok halmaza, mely a fényességről és a színről hordoz információkat. Ezen pontok sűrűségét nevezik „felbontásnak”, s a felbontás fogja meghatározni a részletek mennyiségét, melyet a kép tartalmaz. A felbontás mértékegysége a képpont/hüvelyk (dpi). Ez a képpontok száma 2,5 cm-enként (hüvelykenként). Magasabb felbontásnál (értéknél) a kép részletesebb lesz; alacsonyabb felbontásnál (értéknél) kevésbé lesz részletes.
Megjegyzés Ha a beolvasott képet felnagyítva szeretné kinyomtatni, a beolvasáshoz válasszon a fent ajánlott értéknél nagyobb felbontást.
Adatformátumok A beolvasott képek mentésekor kiválaszthat egy adatformátumot. A legmegfelelőbb adatformátumot célszerű választani annak megfelelően, hogy milyen alkalmazással és hogyan kerülnek majd felhasználásra a képek. A rendelkezésre álló adatformátumok az alkalmazástól és az operációs rendszertől (Windows vagy Mac OS) függően változhatnak. Alább találhatja az egyes képi adatformátumok jellemzőit. PNG (szabványos fájlkiterjesztés: .png) Webhelyeken használt adatformátum.
Színegyeztetés A „Színegyeztetés” funkcióval a színtónust módosíthatja, hogy az eredeti, a képernyőn megjelenő és a kinyomtatott kép színei megfeleljenek egymásnak. A lapolvasón vagy a nyomtatón a színtónusok az alábbiak szerint módosulnak.
Az IJ Network Scanner Selector EX menüje és beállítási képernyője Az IJ Network Scanner Selector EX lehetővé teszi azon lapolvasók vagy nyomtatók kiválasztását, amelyeket a hálózaton keresztüli beolvasáshoz vagy nyomtatáshoz fog használni a számítógépről vagy a kezelőpanelről. Telepítés után az IJ Network Scanner Selector EX megjelenik a tálca értesítési területén.
Kilép az IJ Network Scanner Selector EX programból; a tálca értesítési területéről eltűnik a (Engedélyezve) vagy (Letiltva) ikon. A számítógépről történő beolvasás beállításainak képernyője A hálózaton keresztül történő beolvasás előtt a lapolvasót vagy a nyomtatót ki kell választani az IJ Network Scanner Selector EX segítségével. A tálca értesítési területén kattintson a jobb egérgombbal az ikonra, és válassza a Beállítások... (Settings...
Fontos Ha olyan típusú készüléket használ, amely nem alkalmas a kezelőpanelről végzett hálózaton keresztüli nyomtatásra, a számítógépről történő beolvasás beállításainak képernyőjén megjelenhet a Kezelőpanelről történő beolvasás beállításai (Scan-from-Operation-Panel Settings) elem, ekkor azonban a beállítás nem érhető el.
Az IJ Network Scanner Selector EX eltávolítása Kövesse az alábbi lépéseket, ha el kívánja távolítani számítógépéről az IJ Network Scanner Selector EX alkalmazást. Fontos Nem tud majd beolvasni hálózaton keresztül az IJ Network Scanner Selector EX eltávolítása után. Rendszergazdai jogokkal rendelkező fiókkal lépjen be. 1. Az IJ Network Scanner Selector EX eltávolítása. • Windows 7 vagy Windows Vista esetén: 1.
Egyéb beolvasási módszerek Beolvasás WIA-illesztőprogrammal Beolvasás a Vezérlőpult használatával (csak Windows XP esetén) 172
Beolvasás WIA-illesztőprogrammal Az anyagokat WIA-kompatibilis (Windows Image Acquisition) alkalmazásból olvashatja be. A WIA a Windows XP és az újabb rendszereken implementált illesztőmodell. Lehetővé teszi anyagok beolvasását külön alkalmazás használata nélkül. Az eljárás az adott alkalmazástól függ. A következő eljárások csak példák. Részleteket az alkalmazás kézikönyvében talál. Fontos Windows XP esetén hálózati kapcsolaton keresztül nem lehet beolvasni a WIA-illesztő segítségével.
Válassza a Fotó (alapértelmezett) (Photo (Default)) vagy a Dokumentumok (Documents) lehetőség valamelyikét a beolvasandó anyag alapján. Új Profil (Profile) mentéséhez válassza ki a Profil hozzáadása... (Add profile...) pontot. A részleteket megadhatja az Új profil hozzáadása... (Add New Profile) párbeszédpanelen. • Forrás (Source) Válasszon ki egy lapolvasó típust. Az üveglapról történő beolvasáshoz válassza a Fektetett (Flatbed) lehetőséget.
Beolvasás 1.0 verziójú WIA illesztőprogrammal Az alábbi példa a „Paint” alkalmazásból történő beolvasást mutatja be. 1. Helyezze a beolvasandó anyagot az üveglapra vagy az ADF-be. Anyagok elhelyezése (számítógépről történő beolvasás esetén) 2. Kattintson a alatti Lapolvasóból vagy fényképezőgépből (From scanner or camera) elemre. (Az alkalmazásban válassza ki az anyag beolvasását indító parancsot.) 3. Válasszon a beolvasandó anyagnak megfelelő típust.
A csúszka segítségével állítsa be a fényességet. Mozgassa a csúszkát balra a kép sötétítéséhez, jobbra pedig a világosításához. Értékeket is megadhat (-127-től 127-ig). • Kontraszt (Contrast) A csúszka segítségével állítsa be a kontrasztot. A csúszkát balra mozgatva csökken a kép kontrasztja, ezzel lágyítva a képet. A csúszkát jobbra mozgatva nő a kép kontrasztja, ezzel élesítve a képet. Értékeket is megadhat (-127-től 127-ig). • Felbontás (DPI) (Resolution (DPI)) Adja meg a felbontást.
Beolvasás a Vezérlőpult használatával (csak Windows XP esetén) Elvégezheti a képek beolvasását a Windows XP vezérlőpultjáról, a WIA-illesztő segítségével. Fontos A lapolvasó vagy a nyomtató hálózati csatlakozása esetén nem olvashat be WIA illesztőprogrammal. 1. A Start menüben válassza a Vezérlőpult (Control Panel) pontot. 2.
• Fényesség (Brightness) A csúszka segítségével állítsa be a fényességet. Mozgassa a csúszkát balra a kép sötétítéséhez, jobbra pedig a világosításához. Értékeket is megadhat (-127-től 127-ig). • Kontraszt (Contrast) A csúszka segítségével állítsa be a kontrasztot. A csúszkát balra mozgatva csökken a kép kontrasztja, ezzel lágyítva a képet. A csúszkát jobbra mozgatva nő a kép kontrasztja, ezzel élesítve a képet. Értékeket is megadhat (-127-től 127-ig).
Anyagok elhelyezése (számítógépről történő beolvasás esetén) Tekintse át, hogyan helyezheti az anyagot a lapolvasó vagy nyomtató üveglapjára vagy az ADF-be (az automatikus lapadagolóba). Helyezze el megfelelően az anyagokat a beolvasni kívánt anyag típusa szerint. Máskülönben lehet, hogy az anyagok beolvasása nem lesz megfelelő. Fontos Ne helyezzen tárgyakat a dokumentumfedélre. Amikor kinyitja a dokumentumfedelet, az anyagok beeshetnek a lapolvasóba vagy a nyomtatóba, ami hibás működést okozhat.
dokumentumokat, akkor a beolvasás előtt adja meg a megfelelő adatformátumot. Több anyag elhelyezése Hagyjon 1 cm (0,4 hüvelyk) helyet az anyag és az üveglap szélei (a harántcsíkos rész), valamint az egyes anyagok között. A dokumentumok átlósan vonalazott területen található részeit a készülék nem tudja letapogatni. több, mint 1 cm (0,4 hüvelyk) Megjegyzés Legfeljebb 12 anyagot helyezhet el.
181
Beolvasás a készülék kezelőpaneljének használatával A beolvasott adatok továbbítása a számítógépre a készülék kezelőpaneljének segítségével Alapszintű A beolvasott adatok e-mailhez csatolása a készülék kezelőpaneljének segítségével Beolvasott adatok mentése USB flash meghajtóra a készülék kezelőpaneljének segítségével Beolvasott adatok törlése az USB flash meghajtóról Értékek beállítása a készülék kezelőpaneljén Beállítások hálózaton keresztül történő beolvasás esetén Parancsokra adott válasz kiválasztása a
A beolvasott adatok továbbítása a számítógépre a készülék kezelőpaneljének segítségével A beolvasott adatok továbbítása a számítógépre a készülék kezelőpaneljének segítségével történik. A beolvasott adatok számítógépre való továbbítása előtt ellenőrizze a következőket: • Az MP Drivers telepítve van. Ha az MP Drivers még nincs telepítve, helyezze be a Telepítő CD-ROM lemezt a számítógép lemezmeghajtójába, majd telepítse az MP Drivers programot. • A készülék megfelelően csatlakozik a számítógéphez.
Megjegyzés Ha a beolvasás mód készenléti képernyője jelenik meg az LCD kijelzőn az adatok USBkapcsolaton keresztül csatlakoztatott számítógépre történő továbbításához, akkor a bal oldali Funkció (Function) gombot megnyomva jelenítse meg azt a képernyőt, amelyen kiválaszthatja, hová kerüljenek az adatok. Az alábbi eljárással válassza ki azt a számítógépet, amelyre a beolvasott adatokat továbbítani szeretné. 1. Válassza a Számítógép (PC) elemet, majd nyomja meg az OK gombot. 2.
A készülék automatikusan észleli az eredeti dokumentumok típusát, és optimalizált méretben, felbontással és adatformátumban továbbítja a képet. Fontos Az Autom. beolvasás (Auto scan) beállítást csak akkor választhatja, ha USB-kapcsolattal csatlakoztatott számítógépre továbbítja a beolvasott adatokat. Az eredetiket a típusuknak megfelelően töltse be; ellenkező esetben előfordulhat, hogy néhány dokumentum beolvasása nem lesz megfelelő.
Ha végzett a beolvasással, nyomja meg a bal oldali Funkció (Function) gombot. A készülék továbbítja a beolvasott adatokat a számítógépre. A készülék a Canon IJ Scan Utility programban megadott beállítások szerint továbbítja a számítógépre az adatokat. Miután befejeződött a beolvasás, távolítsa el az eredetit az üveglapról vagy a papírkimeneti nyílásból. Fontos Ha a beolvasás nem megfelelő Autom. beolvasás (Auto scan) esetén, válassza a Dokumentum (Document) vagy Fotó (Photo) értéket az eredetihez a 3.
A beolvasott adatok e-mailhez csatolása a készülék kezelőpaneljének segítségével A beolvasott adatokat e-mailhez csatolhatja a készülék kezelőpaneljének segítségével. A beolvasott adatok e-mailhez csatolása előtt ellenőrizze a következőket: • Az MP Drivers telepítve van. Ha az MP Drivers még nincs telepítve, helyezze be a Telepítő CD-ROM lemezt a számítógép lemezmeghajtójába, majd telepítse az MP Drivers programot. • A készülék megfelelően csatlakozik a számítógéphez.
USB-kapcsolaton keresztül csatlakoztatott számítógép esetén válassza a Helyi (USB) (Local (USB)) beállítást, helyi hálózaton keresztül csatlakozó számítógép esetén pedig válassza ki azt a számítógépet, amelyre továbbítani szeretné a beolvasott adatokat. Megjelenik a beolvasás készenléti képernyője. 5. A gomb segítségével válassza ki a dokumentum típusát. Dokumentum (Document) Dokumentumként olvassa be az üveglapra vagy az ADF-be helyezett eredetit a Beolv. beállít.
• Ha az üveglapra helyezi az eredetit: • Ha a JPEG lehetőséget választja a beolvasás beállítási képernyőjén, a Formát. (Format) beállításnál, a készülék elkezdi a beolvasást, majd továbbítja a beolvasott adatokat a számítógépre, és csatolja őket egy e-mailhez. • Ha a PDF vagy a Tömörített PDF (Compact PDF) lehetőséget választja a beolvasás beállítási képernyőjén, a Formát. (Format) beállításnál, miután befejeződött a beolvasás, megjelenik a jóváhagyási képernyő a beolvasás folytatásával kapcsolatban.
Beolvasott adatok mentése USB flash meghajtóra a készülék kezelőpaneljének segítségével A készülék kezelőpaneljének segítségével a beolvasott adatokat USB flash meghajtóra mentheti. Fontos Ne vegye ki a készülékből az USB flash meghajtót a következő esetekben: Beolvasás közben A beolvasott adatok mentése előtt Biztonsági okokból azt javasoljuk, hogy az USB flash meghajtóra mentett beolvasott adatokról rendszeresen készítsen biztonsági másolatot egy másik hordozóra.
6. A gomb segítségével válassza ki a dokumentum típusát. Dokumentum (Document) Dokumentumként olvassa be az üveglapra vagy az ADF-be helyezett eredetit a Beolv. beállít. (Scan settings) pontban beállítottaknak megfelelően. Fotó (Photo) Fényképként olvassa be az üveglapra helyezett eredetit a Beolv. beállít. (Scan settings) pontban beállítottaknak megfelelően. 7. Nyomja meg a jobb oldali Funkció (Function) gombot a szükséges beállítások elvégzéséhez. Értékek beállítása a készülék kezelőpaneljén 8.
Ha folyamatosan olvassa be az eredeti dokumentumot, legfeljebb 100 oldalnyi képet rögzíthet egy PDF-fájlban. Miután befejeződött a beolvasás, távolítsa el az eredetit az üveglapról vagy a papírkimeneti nyílásból. Megjegyzés Ha az USB flash meghajtó megtelik a képek beolvasása közben, a készülék csak az addig beolvasott képeket menti. A beolvasott adatokat akár 2000 fájlba mentheti PDF vagy JPEG formátumban.
Beolvasott adatok törlése az USB flash meghajtóról Az USB flash meghajtóra beolvasott adatokat törölheti a kezelőpanel használatával. 1. Győződjön meg arról, hogy a készülék bekapcsolt állapotban van. A készülék bekapcsolt állapotának ellenőrzése 2. Csatlakoztassa az USB flash meghajtót az USB flash meghajtó portjához. Az USB flash meghajtó behelyezése 3. Nyomja meg a BEOLVASÁS (SCAN) gombot. Megjelenik az a képernyő, amelyen kiválaszthatja, hogy hová menti az adatokat.
7. A gomb segítségével válassza az Igen (Yes) lehetőséget a megerősítő képernyőn, majd nyomja meg az OK gombot. A készülék elkezdi törölni a fájlt.
Értékek beállítása a készülék kezelőpaneljén Módosítani lehet a beolvasás beállításait, például a méretet, a felbontást és az adatformátumot. A beolvasás készenléti képernyőjén a jobb oldali Funkció (Function) gomb megnyomásával választhatja ki a beállítási lehetőséget. Válassza ki a kívánt beállítást a gomb segítségével, adja meg az értéket a gombbal, majd nyomja meg az OK gombot. Megjegyzés A beolvasási beállítás a következő feltételek fennállása esetén nem használható: Ha az Autom.
Megjegyzés Ha a Legal beállítás van kiválasztva, akkor az ADF-be tegye az eredetit. Ha a 10x15cm(4"x6") (4"x6"(10x15cm)), a 13x18cm(5"x7") (5"x7"(13x18cm)) vagy az Autom. beolvasás (Auto scan) lehetőség van kiválasztva, helyezze az eredetit az üveglapra. 2. Formát. (Format) Válassza ki a beolvasandó adat formátumát. 3. Beol. felb (Scan res) (Beolvasási felbontás) Válassza ki a beolvasás felbontását. 4.
Beállítások hálózaton keresztül történő beolvasás esetén Csatlakoztathatja a lapolvasót vagy a nyomtató egy hálózatra, és megoszthatja azt több számítógép között, illetve beolvashatja a képeket egy adott számítógépre. Fontos Egyidejűleg több felhasználó nem végezhet letapogatást. Megjegyzés Először végezze el a lapolvasó vagy a nyomtató hálózati beállítását a Telepítő CD-ROM segítségével. Hálózati kapcsolaton át a beolvasás az USB-kapcsolat esetén megszokottnál több időt vesz igénybe.
Megjelenik a számítógépről történő beolvasás beállításainak képernyője. 3. Válassza ki a lapolvasót vagy a nyomtatót a Lapolvasók (Scanners) közül. A hálózat beállítása után a lapolvasó vagy a nyomtató MAC-címe általában már ki van választva. Ebben az esetben nem szükséges ismét kiválasztania. Fontos Ha több lapolvasó is található a hálózatban, akkor több típusnév is megjelenik. Ebben az esetben típusonként egy lapolvasót jelölhet ki. 4. Kattintson az OK gombra.
Megjegyzés USB-kapcsolat esetén válassza a „Canon XXX series hálózat” elemet (ahol az „XXX” a típus neve) a Terméknév (Product Name) beállításnál. 3. Kattintson a Beáll.-ok... (Settings...) lehetőségre, ha a hálózathoz csatlakozó másik lapolvasót szeretne használni. 4. Kattintson az (Általános beállítások) gombra, majd kattintson a Kijelölés (Select) gombra a Terméknév (Product Name) programban. Megjelenik az IJ Network Scanner Selector EX számítógépről történő beolvasási beállításainak képernyője.
Megjegyzés Ha az ikon nem látható a tálca értesítési területén, válassza a Start menü Minden program (All Programs) > Canon Utilities > IJ Network Scanner Selector EX > IJ Network Scanner Selector EX pontját. Az ikon megjelenik a tálca értesítési területén, és megnyílik a számítógépről történő beolvasás beállításainak képernyője. Ilyen esetben ugorjon a 3. lépéshez. 2. A tálca értesítési területén kattintson jobb gombbal az IJ Network Scanner Selector EX ikonjára, és válassza a Beállítások... (Settings...
Megjegyzés Ha a hálózaton keresztül több lapolvasó van csatlakoztatva, legfeljebb három lapolvasót választhat ki. 5. Térjen vissza a számítógépről történő beolvasás beállításainak képernyőjére, és kattintson az OK gombra. Megjegyzés Ha a használni kívánt lapolvasó vagy nyomtató nem jelenik meg, ellenőrizze az alábbiakat, kattintson az OK gombra a képernyő bezárásához, majd nyissa meg újra, és próbálja ismét kiválasztani. A MP Drivers telepítve van.
Parancsokra adott válasz kiválasztása a kezelőpanelről, az IJ Scan Utility program segítségével Az IJ Scan Utility alkalmazásban megadhatja, hogy mi történjen a kezelőpanelről történő beolvasás esetén. Megjegyzés A következő leírásokban a kezelőpanelről végrehajtott automatikus beolvasás esetén választható lehetőségek képernyői szerepelnek példaként. 1. Indítsa el az IJ Scan Utility alkalmazást. Az IJ Scan Utility elindítása 2. Kattintson a Beáll.-ok... (Settings...) gombra.
4. Adja meg a képkorrekciókat a Beolvasási beállítások (Scan Options) párbeszédpanelen. 5. Adja meg a fájlnevet és az egyéb beállításokat a Beállítások mentése (Save Settings) párbeszédpanelen. 6. Válassza ki a beolvasás után elindítandó alkalmazást az Alkalmazás-beállítások (Application Settings) párbeszédpanelen.
7. Kattintson az OK gombra. A kezelőpanelről indított beolvasáskor a rendszer a beállított műveletet hajtja végre.