ENGLISH ESPAÑOL Network Setup Troubleshooting Solución de problemas de configuración de red
This manual describes troubleshooting tips for problems you may encounter when setting up. • If you do not find a description for your trouble here, refer to "Troubleshooting" in the on-screen manual: Basic Guide/Advanced Guide. ■ Troubles in Setup/Connections 1 2 Connection checklist Cannot connect to the access point (the access point is not detected) P.2 P.2 2.1 The target access point is not detected P.2 2.2 Cannot connect to the target access point P.2 2.
Troubles in Setup/Connections 1 Connection checklist Before you proceed to Troubleshooting, confirm the following: □ The USB cable is securely connected to the correct port. □ The machine is turned on and the network device is on. If it is, turn it off and then turn it on again. □ If the firewall function of your security software is turned on, a message may appear warning that Canon software is attempting to access the network.
How to set a network key/network password 3.1 About Network Key (Windows)/Network Password (Macintosh) 3.2 How to set a WEP/WPA/WPA2 key (continued) ENGLISH 3 • When using WPA/WPA2 An encryption key used in wireless networks. As using passwords, settings must match among the access point, the machine, and the computer. A WEP key is used in the WEP authentication method, while Passphrase or Pre-Shared Key is used in the WPA/WPA2 authentication method.
The following screen is displayed during setup 5.1 The Access Points screen is displayed during setup 5.1 The Access Points screen is displayed during setup (continued) (C) Configuration The detailed settings dialog box is displayed. The network password (WEP) or the network key (WPA/WPA2) selected in Encryption Method can be confirmed and changed. (D) Connect The Access Points screen is displayed when: Connects to the specified access point. - No access point is detected.
The Printer could not be connected to the specified access point is displayed during setup This message is displayed when the machine could not connect to the target access point. Clicking the OK displays the Access Points screen. For details, refer to “2.2 Cannot connect to the target access point” on page 2. 5.4 The Another access point with the same SSID exists is displayed during setup Cancel the current setup and change the SSID of the access point, then start the setup again. 5.
5.7 The Enter Password screen is displayed during setup The Enter Password screen is displayed if an administrator password is set to the machine which has already been set up. Admin Password Enter the administrator password you have set. The administrator password consists of alphanumeric characters and is no longer than 32 characters. The password is case sensitive. For security, your entry will be displayed by “*” (asterisks) for Windows and “●” (bullets) for Macintosh. 5.
The Card Slot has already been mapped as the network drive. The Card Slot is already available. Click OK to close the screen, then click Next on the Network Setup of the Card Slot screen. 5.11 The Cannot map any more drives, because all the drive letters are assigned is displayed during setup Click Skip to complete the setup. After software installation is complete, remove any drive letter and try the network setup of the Card Slot again using the Canon IJ Network Tool. 6 Re-setting the machine 6.
Restoring the Machine to the Factory Settings 1 e Make sure that Yes is selected and press the OK button. Initializing using the machine’s Operation Panel Follow these steps to restore the machine’s network settings to factory defaults. f Confirm that the right screen appears. After a while, the LAN settings screen returns. a Press the Menu button, use the [ or ] button to select Settings, then press the OK button. The machine’s network settings are restored to factory defaults.
1 ENGLISH Specifications MX860 series Copy Specifications General Specifications Printing resolution 9600 (horizontal)* x 2400 (vertical) (dpi) * Ink droplets can be placed with a pitch of 1/9600 inch at minimum. Interface USB Port: Hi-Speed USB *1 Direct Print Port: PictBridge Bluetooth v2.0 (Option) *2 *3 *4 USB flash drive LAN Port: Wired LAN: 100BASE-TX/10BASE-T Wireless LAN: IEEE802.11b/IEEE802.
Minimum System Requirements Fax Specifications Applicable line Compatibility Data compressing system Modem type Modem speed Transmission speed Scanning image processing Memory Fax resolution Dialing Telephone networking Public Switched Telephone Network (PSTN) G3 / Super G3 (Mono & Color Fax) MH, MR, MMR, JPEG Fax modem 33600 / 31200 / 28800 / 26400 / 24000 / 21600 / 19200 / 16800 / 14400 / 12000 / 9600 / 7200 / 4800 / 2400 bps Automatic fallback Black & white: Approx. 3 seconds/page at 33.
En este manual se ofrecen consejos para la solución de los problemas que pueden aparecer al realizar la configuración. • Si no encuentra una descripción del problema en este manual, consulte el capítulo “Solución de problemas” en el manual en pantalla Guía básica (Basic Guide)/Guía avanzada (Advanced Guide). ■ Problemas durante la instalación o las conexiones 1 2 2.1 Lista de comprobación de las conexiones pág. 2 No se puede conectar con el punto de acceso (no se detecta el punto de acceso) pág.
Problemas durante la instalación o las conexiones 1 Lista de comprobación de las conexiones Antes de ir al apartado correspondiente a la solución de problemas, compruebe lo siguiente: □ El cable USB está conectado firmemente al puerto correcto. □ El equipo está encendido y el dispositivo de red también. En tal caso, apáguelo y vuelva a encenderlo.
3 Cómo establecer una clave de red/contraseña de red 3.1 Acerca de la clave de red (Windows)/contraseña de red (Macintosh) 3.2 Cómo establecer una clave WEP/WPA/WPA2 (continuación) Clave de codificación que se utiliza en redes inalámbricas. Al igual que cuando se utilizan contraseñas, las configuraciones deben coincidir entre los puntos de acceso, el equipo y el ordenador.
Aparece la pantalla siguiente durante la configuración 5.1 5.1 Aparece la pantalla Puntos de acceso (Access Points) durante la configuración (C) Configuración (Configuration) Se muestra el cuadro de diálogo con la configuración detallada. Se puede comprobar y modificar la contraseña de red (WEP) o la clave de red (WPA/WPA2) seleccionada en Método de codificación (Encryption Method). (D) Conectar (Connect) Conecta con el punto de acceso especificado.
Aparece el mensaje No se puede conectar la impresora al punto de acceso especificado (Printer could not be connected to the specified access point) durante la configuración Este mensaje aparece cuando el equipo no se ha podido conectar con el punto de acceso de destino. Al hacer clic en Aceptar (OK), se muestra la pantalla Puntos de acceso (Access Points). Para obtener más información, consulte la sección “2.2 No se puede conectar con el punto de acceso de destino” de la página 2. 5.
5.7 Aparece la pantalla Introducir contraseña (Enter Password) durante la configuración Si se establece una contraseña de administrador en el equipo ya configurado, aparece la pantalla Introducir contraseña (Enter Password). Contraseña del administrador (Admin Password) Introduzca la contraseña del administrador que haya establecido. La contraseña del administrador está formada por caracteres alfanuméricos y no debe superar los 32 caracteres. La contraseña distingue entre mayúsculas y minúsculas.
La ranura para tarjetas ya está asignada como unidad de red. La ranura para tarjetas ya está disponible. Haga clic en Aceptar (OK) para cerrar la pantalla y, a continuación, haga clic en Siguiente (Next) en la pantalla Configuración de la ranura para tarjetas (Setup of the Card Slot) de la red. 5.
Restauración de la configuración de fábrica del equipo 1 e Asegúrese de que se ha seleccionado Sí (Yes) y pulse el botón OK. Inicialización con el panel de control del equipo Siga estos pasos para restaurar la configuración de red de fábrica del equipo. a Pulse el botón Menú (Menu), utilice el botón [ o ] para seleccionar Parámetros (Settings) y, a continuación, pulse el botón OK. f Compruebe que aparece la pantalla que se muestra a la derecha.
Especificaciones MX860 series Especificaciones de copia Especificaciones generales Resolución de impresión (ppp) 9600 (horizontal)* x 2400 (vertical) * Las gotitas de tinta se pueden administrar con un pitch mínimo de 1/9600 pulgadas. Interfaz Puerto USB: USB de alta velocidad*1 Puerto de impresión directa: PictBridge Bluetooth v2.0 (opcional) *2 *3 *4 Unidad flash USB Puerto LAN: LAN por cable: 100BASE-TX/10BASE-T LAN inalámbrica: IEEE802.11b/IEEE802.
Requisitos mínimos del sistema Especificaciones del fax Línea aplicable Compatibilidad Sistema de compresión de datos Tipo de módem Velocidad del módem Velocidad de transmisión Procesamiento de las imágenes de escaneado Memoria Resolución del fax Marcación Conexión de red telefónica Red telefónica pública conmutada (RTPC) G3 / Super G3 (fax mono y color) MH, MR, MMR, JPEG Módem de fax 33 600/31 200/28 800/26 400/24 000/21 600/19 200/16 800/14 400/12 000/9600/7200/4800/2400 bps Respuesta automática Blanc
QT5-2119-V01 XXXXXXXX ©CANON INC.