Getting Started Démarrage Inbetriebnahme Aan de Slag-gids Guida Rapida Para Começar Guía de inicio Ξεκινώντας Uppstartsguide Komme i gang Før du begynder Aloitusopas Read Safety and Important Information (addendum) first. Commencez par lire Sécurité et informations importantes (addendum). Lesen Sie Sicherheitsinformationen und wichtige Hinweise (Anhang) zuerst. Lees eerst Veiligheidsinformatie en belangrijke informatie (addendum). Leggere innanzitutto Informazioni importanti e sulla sicurezza (addendum).
Installing the Printer.................................................................................................................... page 1 Installation de l'imprimante................................................................................................... page 1 Installation des Druckers...........................................................................................................Seite 1 De printer installeren.....................................................................
. Turning on the Printer Web Setup 1 ENGLISH Setting up the printer Connect the power cord. 1. Box Contents Back • Power cord • Ink tanks for setup Important At this time, do not connect any other cables. 2 • • • Setup CD-ROM Safety and Important Information Getting Started (this manual) • b Multi-purpose tray The multi-purpose tray is attached to the underside surface of the cassette. a 2. Removing Packing Materials 1 Open the operation panel and press the ON button.
Setting up the printer 2 Remove the tape and film on the ink tanks. b 3 6 Repeat steps 2 through 5 to install all the ink tanks. • Make sure that all the colors appear. a • Check that no tape is left over. Slowly remove the orange cap. 7 • Important Do not push both sides of the ink tank with the Y-shape air hole blocked. • Do not touch the red areas shown in the figure. Close the scanning unit / cover. you close the scanning unit / cover, the • When internal operations start.
Load paper. • Load plain LTR or A4 size paper with the print side facing down. 7 Tap OK. 8 Tap Next. ENGLISH 4 the paper against the front paper guide, and • Place align the right paper guide to the width of the paper. a 5 b Load the cassette. follow the onscreen instructions to continue • Next, operations. During these operations, you will need to make selections related to sending information. Read "Sending Information To Canon" in Safety and Important Information.
Setting up the printer What device are you connecting? Select a device and follow the relevant section. Computer Computer and smartphone Smartphone No device 6-b page 6 6-a Tap the Stop button, and then select Do not connect > Yes, in this order. Connecting to a Computer If you are using multiple computers, perform these steps on each computer. There are two methods, " Online Setup" and " Using the Setup CD-ROM (Windows Only) Provided". Online Setup 1 4 Access the Canon website from a computer.
1 Insert the Setup CD-ROM into your computer. 2 Follow the instructions for your version of Windows. ENGLISH Using the Setup CD-ROM (Windows Only) Provided Windows 7 a Click Run Msetup4.exe. the AutoPlay screen appears, click • When Run Msetup4.exe. Windows 10/Windows 8.1 a Click on the following message when it appears on the right-hand side of your computer screen. Note If the message does not appear (or is no longer visible), click the File Explorer icon in the taskbar.
Setting up the printer 6-b Connecting to a Smartphone If you are using multiple smartphones, perform these steps on each smartphone. Prepare the following before starting. a Enable the Wi-Fi setting on your smartphone*. b Connect your smartphone to the wireless router* (if you have a wireless router). * See your smartphone and wireless router manuals regarding these procedures for more details. 1 Install the "Canon PRINT Inkjet/SELPHY" app on your smartphone. Search for "Canon PRINT" in the App Store.
ENGLISH Procedures vary for iOS and Android. Follow the instructions for your operating system. 3 Tap Settings on your smartphone's home screen, and tap Canon_ij_XXXX in the Wi-Fi settings. 3 Open the installed app. printer is registered with the • The most appropriate connection method for the environment you are using. Note If a message saying "No printer has been added.
Loading Photo Paper Photo paper can only be loaded in the rear tray. 1 Open the rear tray cover and extend the paper support. 4 Close the feed slot cover. 2 Open the feed slot cover and slide the righthand side paper guide to the far right. 5 Open the operation panel and pull out the paper output tray. the on-screen instructions to set information • Follow for the loaded paper.
Configuration de l'imprimante Configuration Web 3. Mise sous tension de l'imprimante 1 Branchez le cordon d'alimentation. FRANÇAIS 1. Contenu de la boîte Arrière • Cordon d'alimentation • Cartouches d'encre pour la configuration Important À ce stade, ne branchez aucun autre câble. 2 • • • CD-ROM d'installation Sécurité et informations importantes • b Tiroir multifonctions Le tiroir multifonctions est fixé sous la cassette. a Démarrage (ce manuel) 3 2.
Configuration de l'imprimante 2 Retirez la bande et le film sur les cartouches d'encre. b 3 6 Répétez les étapes 2 à 5 pour installer toutes les cartouches d'encre. • Assurez-vous que toutes les couleurs s'affichent. a • Vérifiez qu'il ne reste aucune bande. Retirez doucement le capuchon orange. 7 • • Fermez l'unité de numérisation / capot. vous fermez l'unité de numérisation / capot, • Lorsque les opérations internes commencent.
Chargez du papier. • Chargez du papier ordinaire au format LTR ou A4 face à imprimer vers le bas. 7 Touchez OK. 8 Touchez Suivant. FRANÇAIS 4 le papier contre le guide papier avant et • Placez alignez le guide papier droit sur la largeur du papier. a 5 b Chargez la cassette. suivez les instructions à l'écran pour • Ensuite, poursuivre les opérations. Au cours de ces opérations, 6 vous devrez procéder à des sélections relatives à l'envoi d'informations.
Configuration de l'imprimante Quel périphérique connectez-vous ? Sélectionnez un périphérique et reportez-vous à la section appropriée. Ordinateur Ordinateur et smartphone Smartphone Aucun périphérique 6-b page 6 6-a Touchez le bouton Arrêt (Stop), puis sélectionnez Ne pas connecter > Oui, dans cet ordre. Connexion à un ordinateur Si vous utilisez plusieurs ordinateurs, effectuez ces étapes sur chaque ordinateur.
Utilisation du CD-ROM d'installation (Windows uniquement) fourni 2 Insérez le CD-ROM d'installation dans l'ordinateur. Suivez les instructions correspondant à votre version de Windows. Windows 7 a Cliquez sur Exécuter Msetup4.exe l'écran Lecture automatique • Lorsque apparaît, cliquez sur Exécuter Msetup4.exe. Windows 10/Windows 8.1 FRANÇAIS 1 a Cliquez sur le message suivant lorsqu'il apparaît sur la droite de l'écran de l'ordinateur.
Configuration de l'imprimante 6-b Connexion à un smartphone Si vous utilisez plusieurs smartphones, effectuez ces étapes sur chaque smartphone. Préparez les éléments suivants avant de démarrer. a Activez le paramètre Wi-Fi sur votre smartphone*. b Connectez votre smartphone au routeur sans fil* (si vous disposez d'un routeur sans fil). * Pour plus de détails sur ces procédures, reportez-vous aux manuels de votre smartphone et de votre routeur sans fil.
Les procédures varient pour iOS et Android. Suivez les instructions correspondant à votre système d'exploitation. Touchez Réglages sur l'écran d'accueil du smartphone, puis touchez Canon_ij_XXXX dans les réglages Wi-Fi. Remarque Si Canon_ij_XXXX n'apparaît pas, suivez la procédure de , puis recherchez Canon_ij_XXXX de nouveau. 4 5 3 Ouvrez l'application installée. est enregistrée • L'imprimante avec la méthode de connexion la plus appropriée à l'environnement que vous utilisez.
Chargement de papier photo Le papier photo peut être chargé uniquement dans le réceptacle arrière. 1 Ouvrez le couvercle du réceptacle arrière et déployez le support papier. 4 Fermez le couvercle de la fente d'alimentation. 2 Ouvrez le couvercle de la fente d'alimentation et faites glisser le guide papier droit vers l'extrême droite. 5 Ouvrez le panneau de contrôle et retirez le bac de sortie papier. les instructions à l'écran pour définir les • Suivez informations sur le papier chargé.
Einrichten des Druckers 3. Einschalten des Druckers Web-Einrichtung 1 Schließen Sie das Netzkabel an. 1. Inhalt der Box Rückseite Netzkabel • Tintenbehälter für die Einrichtung Wichtig Schließen Sie zum jetzigen Zeitpunkt keine weiteren Kabel an. 2 • • • Installations-CD-ROM Sicherheitsinformationen und wichtige Hinweise • b Multifunktionsfach Das Multifunktionsfach ist an der Oberfläche der Unterseite der Kassette angebracht. a Inbetriebnahme (dieses Handbuch) 3 2.
Einrichten des Druckers 2 Entfernen Sie das Klebeband und die Folie auf den Tintenbehältern. b 3 6 Wiederholen Sie die Schritte 2 bis 5, um alle Tintenbehälter einzusetzen. • Stellen Sie sicher, dass alle Farben angezeigt werden. a • Überprüfen Sie, ob das gesamte Klebeband entfernt wurde. Nehmen Sie die orangefarbene Kappe langsam ab. 7 • • Schließen Sie Scan-Modul/Abdeckung. Sie das Scan-Modul/die Abdeckung schließen, • Wenn werden die internen Vorgänge gestartet.
4 Legen Sie Papier ein. • Legen Sie Normalpapier des Formats LTR oder A4 mit der bedruckbaren Seite nach unten ein. 7 Tippen Sie auf OK. 8 Tippen Sie auf Weiter (Next). Sie das Papier gegen die vordere • Schieben Papierführung und richten Sie die rechte a 5 b DEUTSCH Papierführung an der Breite des Papiers aus. Legen Sie die Kassette ein. Sie anschließend die Anweisungen auf • Befolgen dem Bildschirm, um den Vorgang fortzusetzen.
Einrichten des Druckers Mit welchem Gerät stellen Sie eine Verbindung her? Wählen Sie ein Gerät aus und befolgen Sie die Anweisungen im entsprechenden Abschnitt. Computer Computer und Smartphone Smartphone Kein Gerät 6-b Seite 6 6-a Tippen Sie auf die Schaltfläche Stopp (Stop) und wählen Sie dann Nicht verbinden (Do not connect) > Ja (Yes) in dieser Reihenfolge aus. Herstellen einer Verbindung mit einem Computer Wenn Sie mehrere Computer verwenden, führen Sie diese Schritte auf jedem Computer aus.
Verwenden der bereitgestellten Installations-CD-ROM (nur Windows) 1 Legen Sie die Installations-CD-ROM in Ihren Computer ein. 2 Befolgen Sie die Anweisungen für Ihre Windows-Version. Windows 7 a Klicken Sie auf Msetup4.exe ausführen (Run Msetup4.exe). der Bildschirm Automatische • Wenn Wiedergabe (AutoPlay)angezeigt wird, Windows 10/Windows 8.1 klicken Sie auf Msetup4.exe ausführen (Run Msetup4.exe).
Einrichten des Druckers 6-b Herstellen einer Verbindung mit einem Smartphone Wenn Sie mehrere Smartphones verwenden, führen Sie diese Schritte auf jedem Smartphone aus. Bereiten Sie Folgendes vor, bevor Sie beginnen. a Aktivieren Sie die Wi-Fi-Einstellung auf Ihrem Smartphone*. b Stellen Sie eine Verbindung zwischen Ihrem Smartphone und dem Wireless Router her* (wenn Sie über einen Wireless Router verfügen).
Die Verfahren unterscheiden sich auf iOS und Android. Befolgen Sie die Anweisungen für Ihr Betriebssystem. Tippen Sie auf dem Startbildschirm Ihres Smartphones auf Einstellungen (Settings) und anschließend in den Wi-Fi-Einstellungen auf Canon_ij_XXXX. Hinweis Wenn Canon_ij_XXXX nicht angezeigt wird, befolgen Sie die Schritte unter und suchen Sie anschließend erneut Canon_ij_XXXX. 4 5 Öffnen Sie die installierte App. 3 Öffnen Sie die installierte App.
Einlegen von Fotopapier Fotopapier kann nur in das hintere Fach eingelegt werden. 1 Öffnen Sie die Abdeckung des hinteren Fachs und ziehen Sie die Papierstütze heraus. 4 Schließen Sie die Abdeckung für den Einzugsschacht. Sie die Anweisungen auf dem Bildschirm, • Befolgen um Informationen für das eingelegte Papier festzulegen. 2 Öffnen Sie die Abdeckung für den Einzugsschacht und schieben Sie die rechte Papierführung ganz nach rechts.
De printer instellen 3. De printer inschakelen Webinstallatie 1 Sluit het netsnoer aan. 1. Inhoud van de doos Achterkant Netsnoer • Inkttanks voor installatie Belangrijk Sluit op dit moment nog geen andere kabels aan. 2 • • • Installatie-cd-rom Veiligheidsinformatie en belangrijke informatie • b Multifunctionele lade De multifunctionele lade is bevestigd aan de onderkant van de cassette. a Aan de Slag-gids (deze handleiding) 3 2.
De printer instellen 2 Verwijder de tape en de folie van de inkttanks. b 3 6 Herhaal de stappen 2 tot en met 5 om alle inkttanks te plaatsen. • Controleer of alle kleuren worden weergegeven. a • Controleer of er geen tape is achtergebleven. Verwijder langzaam het oranje kapje. 7 • • Sluit de scaneenheid / klep. u de scaneenheid / klep sluit, starten de • Wanneer interne bewerkingen. Belangrijk Duw niet op beide zijden van de inkttank waarbij u de Y-vormige luchtopening blokkeert.
4 Plaats papier. • Plaats normaal papier van LTR- of A4-formaat met de afdrukzijde omlaag. 7 Tik op OK. 8 Tik op Volgende (Next). het papier tegen de voorste papiergeleider en • Plaats lijn de rechterpapiergeleider uit met de breedte van het papier. a Plaats de cassette. daarna de instructies op het scherm om • Volg door te gaan. Hierbij moet u selecties maken die betrekking hebben op het verzenden van informatie.
De printer instellen Met welk apparaat maakt u verbinding? Selecteer een apparaat en lees de desbetreffende sectie. Computer Computer en smartphone Smartphone Geen apparaat 6-b pagina 6 6-a Tik op de knop Stoppen (Stop) en selecteer Niet verbinden (Do not connect) > Ja (Yes) in deze volgorde. Verbinden met een computer Als u meerdere computers gebruikt, voert u deze stappen uit op elke computer.
De meegeleverde installatie-cd-rom gebruiken (alleen Windows) Plaats de installatie-cd-rom in de computer. 2 Volg de instructies voor uw versie van Windows. Windows 7 a Klik op Msetup4.exe uitvoeren (Run Msetup4.exe). het scherm Automatisch • Wanneer afspelen (AutoPlay) wordt Windows 10/Windows 8.1 weergegeven, klikt u op Msetup4.exe uitvoeren (Run Msetup4.exe). a Klik op het volgende bericht wanneer dit rechts op het computerscherm wordt weergegeven.
De printer instellen 6-b Verbinden met een smartphone Als u meerdere smartphones gebruikt, voert u deze stappen uit op elke smartphone. Bereid het volgende voor voordat u begint. a Schakel de Wi-Fi-instelling op uw smartphone in*. b Verbind uw smartphone met de draadloze router* (als u een draadloze router gebruikt). * Raadpleeg de handleiding van uw smartphone en draadloze router voor meer informatie over deze procedures. 1 Installeer de app "Canon PRINT Inkjet/SELPHY" op uw smartphone.
De procedures verschillen voor iOS en Android. Volg de instructies voor uw besturingssysteem. Tik op Instellingen (Settings) op het beginscherm van uw smartphone en tik op Canon_ij_XXXX bij de instellingen voor Wi-Fi. Opmerking Als Canon_ij_XXXX niet wordt weergegeven, volgt u de stappen in en zoekt u daarna opnieuw naar Canon_ij_XXXX. 4 5 3 Open de geïnstalleerde app. printer wordt geregistreerd • De met de meest geschikte verbindingsmethode voor de omgeving die u gebruikt.
Fotopapier plaatsen Fotopapier kan alleen in de achterste lade worden geplaatst. 1 Open de klep van de achterste lade en trek de papiersteun uit. 4 Sluit het klepje over de invoersleuf. 2 Open het klepje over de invoersleuf en schuif de papiergeleider aan de rechterkant helemaal naar rechts. 5 Open het bedieningspaneel en trek de papieruitvoerlade uit. de instructies op het scherm om informatie over • Volg het geplaatste papier in te stellen.
Impostazione della stampante 3. Accensione della stampante Impostazione Web 1 Collegare il cavo di alimentazione. 1. Contenuto della scatola Retro • Cavo di alimentazione • Serbatoi d'inchiostro per l'impostazione Importante In questa fase, non collegare altri cavi. 2 • • • CD-ROM di installazione Informazioni importanti e sulla sicurezza • b Vassoio multiuso Il vassoio multiuso è attaccato alla superficie inferiore del cassetto. a Guida Rapida (questo manuale) 3 2.
Impostazione della stampante 2 Rimuovere il nastro e la pellicola dai serbatoi d'inchiostro. b 3 6 Ripetere i passi da 2 a 5 per installare tutti i serbatoi d'inchiostro. • Assicurarsi che vengano visualizzati tutti i colori. a • Controllare che non vi sia rimasto del nastro. Rimuovere lentamente il coperchietto arancione. 7 • • Chiudere l'unità di scansione / coperchio. si chiude l'unità di scansione / coperchio, • Quando hanno inizio le operazioni interne.
4 Caricare la carta. • Caricare carta comune di formato LTR o A4 con il lato di stampa rivolto verso il basso. 7 Toccare OK. 8 Toccare Avanti (Next). la carta contro la guida della carta • Posizionare anteriore e allineare la guida della carta di destra alla larghezza della carta. a 5 b Caricare il cassetto. seguire le istruzioni a video per • Successivamente, continuare le operazioni. Durante queste operazioni, 6 Estrarre il vassoio di uscita della carta. 9 Toccare Avanti (Next).
Impostazione della stampante Quale periferica si sta connettendo? Selezionare una periferica e seguire la sezione pertinente. Computer Computer e smartphone Smartphone Nessuna periferica 6-b pagina 6 6-a Toccare il pulsante Stop e selezionare Non connettere (Do not connect) > Sì (Yes), in questo ordine. Connessione a un computer Se si utilizzano più computer, eseguire questi passaggi su ciascun computer.
Utilizzo del CD-ROM di installazione fornito (solo per Windows) 1 Inserire il CD-ROM di installazione nel computer. 2 Seguire le istruzioni per la versione di Windows in uso. Windows 7 a Fare clic su Esegui Msetup4.exe (Run Msetup4.exe). viene visualizzata la schermata • Quando Riprod. automatica (AutoPlay), Windows 10/Windows 8.1 fare clic su Esegui Msetup4.exe (Run Msetup4.exe). a Fare clic sul seguente messaggio quando viene visualizzato sul lato destro dello schermo del computer.
Impostazione della stampante 6-b Connessione a uno smartphone Se si utilizzano più smartphone, eseguire questi passaggi su ciascuno smartphone. Prima di iniziare, effettuare quanto segue. a Abilitare l'impostazione Wi-Fi sullo smartphone*. b Connettere lo smartphone al router wireless* (se si dispone di un router wireless). * Per ulteriori informazioni in merito a queste procedure, vedere i manuali dello smartphone e del router wireless. 1 Installare l'app "Canon PRINT Inkjet/SELPHY" sullo smartphone.
Le procedure variano tra iOS e Android. Seguire le istruzioni relative al sistema operativo in uso. Toccare Impostazioni (Settings) nella schermata iniziale dello smartphone, quindi toccare Canon_ij_XXXX nelle impostazioni Wi-Fi. Nota Se Canon_ij_XXXX non appare, seguire la procedura in , quindi cercare di nuovo Canon_ij_XXXX. 4 5 3 Aprire l'app installata. stampante è registrata con • Lail metodo di connessione più appropriato all'ambiente in uso.
Caricamento della carta fotografica La carta fotografica può essere caricata solo nel vassoio posteriore. 1 2 Aprire il coperchio del vassoio posteriore ed estendere il supporto per la carta. Aprire il coperchio dell'alimentatore manuale e far scorrere la guida della carta di destra verso l'estrema destra. 4 Chiudere il coperchio dell'alimentatore manuale. le istruzioni sullo schermo per impostare le • Seguire informazioni per la carta caricata.
Configurando a impressora 3. Ligando a Impressora Configuração da Web 1 Conecte o cabo de alimentação. 1. Conteúdo da Caixa Parte traseira • Cabo de alimentação • Cartuchos de tinta para configuração Importante Não conecte quaisquer outros cabos ainda. 2 • • • CD-ROM de instalação Informações Importantes e Sobre Segurança • b Bandeja multipropósito A bandeja multipropósito está anexada à superfície inferior do cassete. a Para Começar (este manual) 3 2.
Configurando a impressora 2 Remova a fita e o filme dos cartuchos de tinta. b 3 6 Repita as etapas 2 a 5 para instalar todos os cartuchos de tinta. • Verifique se todas as cores aparecem. a • Verifique se não foi deixada nenhuma fita. Remova a tampa laranja lentamente. 7 • • Feche a unidade de digitalização/tampa. fechar a unidade de digitalização/tampa, as • Aooperações internas se iniciam.
4 Coloque o papel. • Carregue papel comum tamanho LTR ou A4 com o lado a ser impresso virado para baixo. 7 Toque em OK. 8 Toque em Avançar (Next). o papel na guia do papel frontal e alinhe a • Coloque guia do papel direita com a largura do papel. a 5 b Carregue o cassete. seguida, siga as instruções na tela para continuar • Em as operações. Durante essas operações, será preciso fazer seleções relacionadas ao envio de informações.
Configurando a impressora Qual dispositivo você está conectando? Selecione um dispositivo e siga a seção relevante. Computador Computador e smartphone Smartphone Nenhum dispositivo 6-b página 6 6-a Toque no botão Parar (Stop) e selecione Não conectar (Do not connect) > Sim (Yes), nesta ordem. Conectando a um Computador Se você estiver usando vários computadores, execute estas etapas em cada computador.
Usando o CD-ROM de instalação (Somente Windows) fornecido 1 Insira o CD-ROM de instalação no seu computador. 2 Siga as instruções para a sua versão do Windows. Windows 7 a Clique em Executar Msetup4.exe (Run Msetup4.exe). a tela Reprodução Automática • Quando (AutoPlay) for exibida, clique em Executar Windows 10/Windows 8.1 Msetup4.exe (Run Msetup4.exe). a Clique na mensagem a seguir quando ela for exibida no lado direito da tela do seu computador.
Configurando a impressora 6-b Conectando a um smartphone Se você estiver usando vários smartphones, execute estas etapas em cada smartphone. Prepare o seguinte antes de iniciar. a Ative a configuração Wi-Fi no seu smartphone*. b Conecte seu smartphone ao roteador sem fio* (se você tiver um roteador sem fio). * Consulte os manuais do seu smartphone e do seu roteador sem fio para obter mais detalhes sobre esses procedimentos. 1 Instale o aplicativo "Canon PRINT Inkjet/SELPHY" no seu smartphone.
Os procedimentos podem variar para iOS e Android. Siga as instruções para o seu sistema operacional. 3 Toque em Configurações (Settings) na tela inicial do seu smartphone e depois em Canon_ij_XXXX nas configurações de Wi-Fi. Nota Se Canon_ij_XXXX não for exibido, siga o procedimento em , depois busque por Canon_ij_XXXX novamente. 4 5 Abra o aplicativo instalado. 3 Abra o aplicativo instalado. está registrada • Acomimpressora o método de conexão mais apropriado para o ambiente que você está usando.
Colocando Papel Fotográfico Papel fotográfico só pode ser carregado na bandeja traseira. 1 Abra a tampa da bandeja traseira e estenda o suporte de papel. 4 Feche a tampa do slot de alimentação. 2 Abra a tampa do slot de alimentação e deslize a guia do papel do lado direito para a extrema direita. 5 Abra o painel de controle e puxe a bandeja de saída do papel para fora. as instruções na tela para definir informações • Siga sobre o papel carregado.
Configuración de la web 3. Encender la impresora 1 ESPAÑOL Instalación de la impresora Conecte el cable de alimentación. 1. Contenido de la caja Atrás • Cable de alimentación • Depósitos de tinta para configuración Importante En este momento, no conecte ningún otro cable. 2 • • • CD-ROM de instalación Información de seguridad e información importante • b Bandeja multiusos La bandeja multiusos está acoplada a la superficie de la cara inferior del cassette.
Instalación de la impresora 2 Retire la cinta y la película de los depósitos de tinta. b 6 Repita los pasos 2 a 5 para instalar todos los otros depósitos de tinta. • Asegúrese de que aparezcan todos los colores. a que la cinta se ha eliminado • Compruebe completamente. 3 Retire la tapa naranja despacio. 7 • • Cierre la cubierta/unidad de escaneado. cierre la cubierta/unidad de escaneado, se • Cuando iniciarán las operaciones internas.
Cargue el papel. • Cargue papel normal de tamaño LTR o A4 con el lado de impresión hacia abajo. 7 Puntee OK. 8 Puntee Siguiente (Next). ESPAÑOL 4 el papel delante de la guía del papel frontal • Coloque y alinee la guía del papel derecha con el ancho del papel. a 5 b Cargue el cassette. siga las instrucciones en pantalla para • Después, continuar con las operaciones. Durante el transcurso de estas operaciones, tendrá que hacer selecciones relacionadas con el envío de información.
Instalación de la impresora ¿Qué dispositivo va a conectar? Seleccione un dispositivo y siga la sección relevante. Ordenador Ordenador y teléfono inteligente Teléfono inteligente Sin dispositivo 6-b página 6 6-a Puntee el botón Parar (Stop) y, a continuación, seleccione No conectar (Do not connect) > Sí (Yes), en este orden. Conectar al ordenador Si utiliza varios ordenadores, realice estos pasos en cada ordenador.
1 Introduzca el CD-ROM de instalación en su ordenador. 2 Siga las instrucciones para su versión de Windows. Windows 7 a Haga clic en Ejecutar Msetup4.exe (Run Msetup4.exe). se muestre la pantalla • Cuando Reproducción automática (AutoPlay), Windows 10/Windows 8.1 haga clic en Ejecutar Msetup4.exe (Run Msetup4.exe). a Haga clic en el mensaje siguiente cuando se muestre en el lado derecho de la pantalla del ordenador.
Instalación de la impresora 6-b Conexión con un teléfono inteligente Si utiliza varios teléfonos inteligentes, realice estos pasos en cada teléfono inteligente. Prepare lo siguiente antes de empezar. a Active la configuración de Wi-Fi en su teléfono inteligente*. b Conecte su teléfono inteligente al router inalámbrico* (si tiene un router inalámbrico). * Consulte los manuales de su teléfono inteligente y del router inalámbrico relacionados con estos procedimientos para obtener más detalles.
3 Toque Ajustes (Settings) en la pantalla de inicio de su teléfono inteligente y después toque Canon_ij_XXXX en los ajustes de Wi-Fi. Nota Si Canon_ij_XXXX no aparece, siga el procedimiento en y después busque Canon_ij_XXXX de nuevo. 4 5 Abra la aplicación instalada. 3 ESPAÑOL Los procedimientos son diferentes para iOS y Android. Siga las instrucciones para su sistema operativo. Abra la aplicación instalada.
Carga de papel fotográfico El papel fotográfico solo se pude cargar en la bandeja posterior. 1 Abra la cubierta de la bandeja posterior y extienda el soporte del papel. 4 Cierre la cubierta de la ranura de alimentación. 2 Abra la cubierta de la ranura de alimentación y deslice la guía del papel del lado derecho totalmente hacia la derecha. 5 Abra el panel de control y retire la bandeja de salida del papel. las instrucciones en pantalla para definir la • Siga información para el papel cargado.
Ρύθμιση του εκτυπωτή 3. Ενεργοποίηση του εκτυπωτή Διαδικτυακή ρύθμιση 1 Συνδέστε το καλώδιο τροφοδοσίας. ΕΛΛΗΝΙΚΗ 1. Περιεχόμενα συσκευασίας Πίσω μέρος • Καλώδιο τροφοδοσίας • Δοχεία μελάνης για εγκατάσταση Σημαντικό Προς το παρόν, μη συνδέσετε άλλα καλώδια. 2 • • • CD-ROM εγκατάστασης Πληροφορίες για την ασφάλεια και σημαντικές πληροφορίες • b Θήκη πολλαπλών λειτουργιών Η θήκη πολλαπλών λειτουργιών βρίσκεται στο κάτω μέρος της κασέτας. a Ξεκινώντας (αυτό το εγχειρίδιο) 3 2.
Ρύθμιση του εκτυπωτή 2 Αφαιρέστε την ταινία και τη μεμβράνη από τα δοχεία μελάνης. b 3 6 • Βεβαιωθείτε ότι εμφανίζονται όλα τα χρώματα. a • Ελέγξτε ότι δεν έχει παραμείνει ταινία. Αφαιρέστε αργά το πορτοκαλί κάλυμμα. 7 • • 4 5 2 Επαναλάβετε τα βήματα 2 έως 5 για να τοποθετήσετε όλα τα δοχεία μελάνης. Κλείστε τη μονάδα σάρωσης / κάλυμμα. κλείσετε τη μονάδα σάρωσης / κάλυμμα, • Όταν εκκινούν οι εσωτερικές λειτουργίες.
Τοποθετήστε χαρτί. • Τοποθετήστε απλό χαρτί μεγέθους LTR ή A4 με την πλευρά εκτύπωσης στραμμένη προς τα κάτω. 7 Πατήστε OK. 8 Πατήστε Επόμενο (Next). ΕΛΛΗΝΙΚΗ 4 το χαρτί στον μπροστινό οδηγό χαρτιού • Τοποθετήστε και ευθυγραμμίστε τον δεξιό οδηγό χαρτιού με το πλάτος του χαρτιού. a 5 b Τοποθετήστε την κασέτα. συνέχεια, ακολουθήστε τις οδηγίες στην οθόνη • Στη για να συνεχίσετε τις λειτουργίες.
Ρύθμιση του εκτυπωτή Τι συσκευή σκοπεύετε να συνδέσετε; Επιλέξτε μια συσκευή και ακολουθήστε τις οδηγίες στη σχετική ενότητα. Υπολογιστής Υπολογιστής και smartphone Smartphone Καμία συσκευή 6-b σελίδα 6 6-a Πατήστε ελαφρά το κουμπί Στοπ (Stop) και, στη συνέχεια, επιλέξτε Μην γίνει σύνδεση (Do not connect) > Ναι (Yes), με αυτή τη σειρά. Σύνδεση με υπολογιστή Εάν χρησιμοποιείτε πολλούς υπολογιστές, εκτελέστε αυτά τα βήματα σε κάθε υπολογιστή.
Χρήση του παρεχόμενου CD-ROM εγκατάστασης (Μόνο για Windows) Τοποθετήστε το CD-ROM εγκατάστασης στον υπολογιστή σας. 2 Ακολουθήστε τις οδηγίες για την έκδοση των Windows που διαθέτετε. Windows 7 a Κάντε κλικ στο Εκτέλεση Msetup4.exe (Run Msetup4.exe). εμφανιστεί η οθόνη Αυτόματη • Όταν αναπαραγωγή (AutoPlay), κάντε κλικ Windows 10/Windows 8.1 στο Εκτέλεση Msetup4.exe (Run Msetup4.exe). a Κάντε κλικ στο ακόλουθο μήνυμα όταν εμφανιστεί στη δεξιά πλευρά της οθόνης του υπολογιστή σας.
Ρύθμιση του εκτυπωτή 6-b Σύνδεση με Smartphone Εάν χρησιμοποιείτε πολλά smartphone, εκτελέστε αυτά τα βήματα σε κάθε smartphone. Προετοιμάστε τα εξής προτού ξεκινήσετε. a Ενεργοποιήστε τη ρύθμιση Wi-Fi στο smartphone σας*. b Συνδέστε το smartphone σας στον ασύρματο δρομολογητή* (εάν έχετε ασύρματο δρομολογητή). * Για περισσότερες λεπτομέρειες, ανατρέξτε στα εγχειρίδια του smartphone και του ασύρματου δρομολογητή σχετικά με αυτές τις διαδικασίες.
3 Πατήστε Ρυθμίσεις (Settings) στην αρχική οθόνη του smartphone και μετά πατήστε Canon_ij_XXXX στις ρυθμίσεις Wi-Fi. 3 Ανοίξτε την εγκατεστημένη εφαρμογή. δηλώνεται με • Οτηνεκτυπωτής καταλληλότερη μέθοδο σύνδεσης για το περιβάλλον που χρησιμοποιείτε. Σημείωση Εάν δεν εμφανιστεί η επιλογή Canon_ij_XXXX, ακολουθήστε τη διαδικασία στο και επαναλάβετε την αναζήτηση για το Canon_ij_XXXX. 4 ΕΛΛΗΝΙΚΗ Οι διαδικασίες διαφέρουν για iOS και Android.
Τοποθέτηση φωτογραφικού χαρτιού Το φωτογραφικό χαρτί μπορεί να τοποθετηθεί μόνο στην πίσω θήκη. 1 Ανοίξτε το κάλυμμα πίσω θήκης και εκτείνετε την υποστήριξη χαρτιού. 4 Κλείστε το κάλυμμα υποδοχής τροφοδοσίας. 2 Ανοίξτε το κάλυμμα υποδοχής τροφοδοσίας και σύρετε το δεξιό οδηγό χαρτιού προς τα δεξιά έως το τέρμα. 5 Ανοίξτε τον πίνακα λειτουργίας και τραβήξτε έξω τη θήκη εξόδου χαρτιού. τις οδηγίες στην οθόνη για να ορίσετε • Ακολουθήστε πληροφορίες για το τοποθετημένο χαρτί.
Ställa in skrivaren 3. Slå på skrivaren Webbinstallation 1 Anslut strömkabeln. 1. Boxens innehåll Baksida Strömkabel • Bläckbehållare för installation Viktigt! Anslut inga andra kablar än strömkabeln ännu. 2 • • • Installations-CD • Information om säkerhet och annan viktig information b Multifunktionsfack Multifunktionsfacket är fäst på kassettens undersida. a Uppstartsguide (denna handbok) 3 2. Ta bort förpackningsmaterial 1 Öppna manöverpanelen och tryck på knappen PÅ (ON).
Ställa in skrivaren 2 Ta bort tejpen och filmen på bläckbehållarna. b 3 6 Upprepa steg 2 till 5 för att installera alla bläckbehållare. • Kontrollera att alla färger visas. a • Kontrollera att ingen tejp sitter kvar. Ta långsamt bort det orange locket. 7 • • Stäng skannerenheten/luckan. du stänger skannerenheten/luckan startar de • När interna funktionerna. Viktigt! Tryck inte på båda sidor av bläckbehållaren med det Y-formade lufthålet blockerat. Försiktighet Akta fingrarna.
4 Fyll på papper. • Lägg i vanligt LTR- eller A4-papper med utskriftssidan vänd nedåt. 7 Tryck på OK. 8 Tryck på Nästa (Next). papperet mot den främre pappersledaren och • Lägg justera den högra pappersledaren efter papperets a 5 b SVENSKA bredd. Ladda kassetten. följer du instruktionerna på skärmen för • Därefter att fortsätta användningen. Under användningen behöver du göra val i samband med överföring av information.
Ställa in skrivaren Vilken enhet ansluter du? Välj en enhet och följ lämpligt avsnitt. Dator Dator och smarttelefon Smarttelefon Ingen enhet 6-b sida 6 6-a Tryck på knappen Stopp (Stop) och välj sedan Anslut inte (Do not connect) > Ja (Yes) i den ordningen. Ansluta till dator Om du använder flera datorer utför du dessa steg på varje dator. Det finns två metoder, " Onlineinstallation" och " Använda den tillhandahållna installations-CD:n (endast Windows)".
Använda den tillhandahållna installations-CD:n (endast Windows) 1 Sätt i installations-CD:n i datorn. 2 Följ instruktionerna för din version av Windows. Windows 7 a Klicka på Kör Msetup4.exe (Run Msetup4.exe). skärmen Spela upp automatiskt • När (AutoPlay) visas klickar du på Kör Msetup4.exe (Run Msetup4.exe). Windows 10/Windows 8.1 Obs! Om meddelandet inte visas (eller inte längre syns) klickar du på ikonen Utforskaren (File Explorer) i aktivitetsfältet.
Ställa in skrivaren 6-b Ansluta till en smarttelefon Om du använder flera smarttelefoner utför du dessa steg på varje smarttelefon. Förbered följande innan du börjar. a Aktivera inställningen Wi-Fi på smarttelefonen*. b Anslut smarttelefonen till den trådlösa routern* (om du har en trådlös router). * Läs smarttelefonens och den trådlösa routerns handböcker om dessa procedurer för mer detaljer. 1 Installera appen ”Canon PRINT Inkjet/SELPHY” på smarttelefonen. Sök efter ”Canon PRINT” i App Store.
Åtgärderna varierar för iOS och Android. Följ instruktionerna för ditt operativsystem. 3 Tryck på Inställningar (Settings) på hemskärmen på din smarttelefon och tryck på Canon_ij_XXXX i Wi-Fi-inställningarna. 3 Öppna den installerade appen. är registrerad • Skrivaren med den lämpligaste Obs! Om ett meddelande med texten "Ingen skrivare har lagts till. Vill du utföra skrivarinställningar? (No printer has been added.
Fylla på fotopapper Fotopapper kan endast fyllas på i det bakre facket. 1 Öppna det bakre fackets lock och dra ut pappersstödet. 4 Stäng luckan för matningsfacket. 2 Öppna luckan för matningsfacket och skjut höger pappersledare längst ut till höger. 5 Öppna manöverpanelen och dra ut utmatningsfacket. instruktionerna på skärmen för att ange • Följ information om det påfyllda papperet.
Konfigurere skriveren 3. Slå på skriveren Nettoppsett 1 Koble til strømledningen. 1. Innhold i esken Bakside Strømledning • Blekktanker til oppsett Viktig! Ikke koble til andre kabler på dette tidspunktet. 2 • • • Installerings-CD-ROM Sikkerhetsinformasjon og viktig informasjon • b Flerbruksskuff Flerbruksskuffen er festet til undersiden av kassetten. a Komme i gang (denne manualen) 3 2. Fjerne beskyttelsesmateriale 1 Åpne betjeningspanelet og trykk på PÅ (ON)knappen.
Konfigurere skriveren 2 Fjern tapen og filmen på blekktankene. b 3 6 Gjenta trinn 2 til 5 for å installere alle blekktankene. • Kontroller at alle fargene vises. a • Kontroller at det ikke er igjen tape. Fjern sakte den oransje korken. 7 • Viktig! Ikke trykk inn begge sider av blekktanken når det Y-formede lufthullet er blokkert. • Ikke berør de røde områdene som er vist på figuren. Lukk skanneenheten/dekselet. du lukker skanneenheten/dekselet, starter de • Når interne operasjonene.
4 Legg i papir. • Legg inn papir i LTR- eller A4-størrelse med utskriftssiden ned. 7 Trykk på OK. 8 Trykk på Neste (Next). papiret mot fremre papirfører, og juster høyre • Plasser papirfører ut fra bredden på papiret. a Sett inn kassetten. deretter instruksjonene på skjermen for å • Følg fortsette operasjonene. Under disse operasjonene må du gjøre noen valg knyttet til sending av informasjon. Les "Sende informasjon til Canon" i Sikkerhetsinformasjon og viktig informasjon.
Konfigurere skriveren Hvilken enhet kobler du til? Velg en enhet og følg det relevante avsnittet. Datamaskin Datamaskin og smarttelefon Smarttelefon Ingen enhet 6-b side 6 6-a Trykk på Stopp (Stop)knappen og velg deretter Ikke koble til (Do not connect) > Ja (Yes), i denne rekkefølgen. Koble til en datamaskin Hvis du bruker flere datamaskiner, utfører du disse trinnene på hver datamaskin. Det finnes to metoder: " Tilkoblet oppsett" og " Bruke den medfølgende installeringsCD-ROM-en (bare Windows)".
Bruke den medfølgende installerings-CD-ROM-en (bare Windows) 1 Sett inn installerings-CDROM-en i datamaskinen. 2 Følg instruksjonene for din Windowsversjon. Windows 7 a Klikk på Kjør Msetup4.exe (Run Msetup4.exe). skjermbildet Spill av automatisk • Når (AutoPlay) vises, klikker du på Kjør Windows 10/Windows 8.1 Msetup4.exe (Run Msetup4.exe). Merk Hvis meldingen ikke vises (eller ikke lenger er synlig), klikker du på Filutforsker (File Explorer)-ikonet på oppgavelinjen.
Konfigurere skriveren 6-b Koble til en smarttelefon Hvis du bruker flere smarttelefoner, utfører du disse trinnene på hver smarttelefon. Klargjør følgende før du starter. a Aktiver Wi-Fi-innstillingen på smarttelefonen*. b Koble smarttelefonen til den trådløse ruteren* (hvis du har en trådløs ruter). * Se manualene for smarttelefonen og den trådløse ruteren for å få flere detaljer om disse prosedyrene. 1 Installer "Canon PRINT Inkjet/SELPHY"-appen på smarttelefonen.
Prosedyrene varierer for iOS og Android. Følg instruksjonene for ditt operativsystem. Trykk på Innstillinger (Settings) på smarttelefonens hjem-skjerm, og velg Canon_ij_XXXX i Wi-Fi-innstillingene. Merk Hvis Canon_ij_XXXX ikke vises, følger du prosedyren i , og søker etter Canon_ij_XXXX på nytt. 4 5 3 Åpne den installerte appen. registreres med • Skriveren tilkoblingsmetoden som er mest egnet for miljøet du bruker. Merk Hvis meldingen "Ingen skrivere er lagt til.
Legge i fotopapir Fotopapir kan kun legges i bakskuffen. 1 Åpne bakskuffdekselet, og forleng papirstøtten. 4 Lukk spordekselet for mating. 2 Åpne spordekselet for mating og skyv høyre papirfører helt mot høyre. 5 Åpne betjeningspanelet, og trekk ut papirutmatingsbrettet. instruksjonene på skjermen for å angi • Følg informasjon for papiret som er lagt inn. b a 3 a Legg inn flere ark med fotopapir med utskriftssiden opp, og skyv papirføreren fra siden mot kanten på papirstabelen.
Konfiguration af printeren 3. Tænd printeren Webopsætning 1 Tilslut netledningen. 1. Æskens indhold Bagside • Netledning • Blækbeholdere til opsætning Vigtigt På dette tidspunkt må du ikke tilslutte nogen andre kabler. 2 • • • Installations-cd-rom Sikkerhedsoplysninger og vigtige oplysninger • b Universalbakke Universalbakken sidder fast på undersiden af kassetten. a Før du begynder (denne vejledning) 3 2. Fjern emballage 1 Åbn kontrolpanelet, og tryk på knappen TIL (ON).
Konfiguration af printeren 2 Fjern tapen og filmen på blækbeholderne. b 3 6 Gentag trin 2 til 5 for at installere alle blækbeholderne. • Sørg for, at alle farverne vises. a • Tjek, at der ikke er noget tape tilbage. Fjern langsomt den orange hætte. 7 • • Luk scanningsenheden/dækslet. du lukker scanningsenheden/dækslet, startes de • Når interne handlinger. Vigtigt Undlad at trykke på begge sider af blækbeholderen, mens det Y-formede hul er blokeret. Forsigtig Pas på dine fingre.
4 Ilæg papir. • Ilæg almindeligt LTR- eller A4-papir med udskriftssiden nedad. 7 Tryk på OK. 8 Tryk på Næste (Next). papiret mod det forreste papirstyr, og juster • Placer derefter det højre papirstyr med bredden af papiret. a 5 b Isæt kassetten. derefter instruktionerne på skærmen for • Følg at fortsætte med processen. Du bliver bedt om at foretage valg vedrørende afsendelse af oplysninger. Læs "Send oplysninger til Canon" i Sikkerhedsoplysninger og vigtige oplysninger.
Konfiguration af printeren Hvilken enhed tilslutter du? Vælg en enhed, og følg oplysningerne i det relevante afsnit. Computer Computer og smartphone Smartphone Ingen enhed 6-b side 6 6-a Tryk på knappen Stop, og vælg derefter Opret ikke forbindelse (Do not connect) > Ja (Yes) i denne rækkefølge. Tilslutning til en computer Hvis du bruger flere computere, skal du udføre disse trin på hver computer.
Brug af den medfølgende installations-cd-rom (kun Windows) 1 Indsæt installations-cdrom'en i din computer. 2 Følg instruktionerne for din version af Windows. Windows 7 a Klik på Kør Msetup4.exe (Run Msetup4.exe). skærmbilledet Automatisk • Når afspilning (AutoPlay) vises, skal Windows 10/Windows 8.1 du klikke på Kør Msetup4.exe (Run Msetup4.exe). a Klik på følgende meddelelse, når den vises til højre på din computerskærm.
Konfiguration af printeren 6-b Tilslutning til en smartphone Hvis du bruger flere smartphones, skal du udføre disse trin på hver smartphone. Forbered følgende inden start. a Aktiver indstillingen Wi-Fi på din smartphone*. b Tilslut din smartphone til den trådløse router* (hvis du har en trådløs router). * Du kan finde flere oplysninger om disse fremgangsmåder i brugervejledningerne til din smartphone og trådløse router. 1 Installer appen "Canon PRINT Inkjet/SELPHY" på din smartphone.
Der skal benyttes forskellige fremgangsmåder til iOS og Android. Følg instruktionerne for dit operativsystem. Tryk på Indstillinger (Settings) på startskærmen på din smartphone, og tryk på Canon_ij_XXXX under Wi-Fi indstillinger. Bemærk Hvis Canon_ij_XXXX ikke vises, skal du følge fremgangsmåden i og derefter søge efter Canon_ij_XXXX igen. 4 5 3 Åbn den installerede app. registreres med den mest • Printeren relevante forbindelsesmetode for det miljø, som du bruger.
Ilægning af fotopapir Der kan kun lægges fotopapir i den bagerste bakke. 1 Åbn dækslet til bagerste bakke, og træk papirstøtten ud. 4 Luk arkføderdækslet. 2 Åbn arkføderdækslet, og skub det højre papirstyr helt ud til højre. 5 Åbn kontrolpanelet, og træk udbakken til papir ud. instruktionerne på skærmen for at angive • Følg oplysninger for det ilagte papir. b a a 3 b Ilæg flere ark fotopapir med udskriftssiden opad, og skub papirstyret på siden mod kanten af papirstakken.
Tulostimen asennus 3. Virran kytkeminen tulostimeen Verkkoasennus 1 Kytke virtajohto. 1. Paketin sisällys Takaosa Virtajohto • Mustesäiliöt asennusta varten Tärkeää Älä tässä vaiheessa kytke mitään muuta johtoa. 2 • • • Asennus-CD Turvallisuus ja tärkeitä tietoja • b Monitoimitaso Monitoimitaso kiinnitetään kasetin alapintaan. Aloitusopas (tämä käyttöopas) a 3 2. Pakkausmateriaalien poistaminen 1 Poista pakkausmateriaalit laitteesta ja hävitä ne.
Tulostimen asennus 2 Poista teippi ja kalvo mustesäiliöistä. b 3 6 Toista vaiheet 2 - 5 asentaessasi kaikki mustesäiliöt. • Varmista, että kaikki värit tulevat näkyviin. a • Tarkista, ettei teippiä jää mihinkään kiinni. Irrota oranssi suojus hiljaa. 7 • • Sulje skannausyksikkö/kansi. suljet skannausyksikön/kannen, sisäiset • Kun toiminnot käynnistyvät. Tärkeää Älä paina mustesäiliön molemmilta puolilta niin, että Y-muotoinen ilmareikä tukkeutuu. Huomio Varo sormiasi.
4 Lisää paperia. • Aseta tavallinen LTR- tai A4-kokoinen paperi tulostuspuoli alaspäin. 7 Napauta OK. 8 Napauta Seuraava (Next). paperi edessä olevaa paperiohjainta vasten • Aseta ja kohdista oikeanpuoleinen paperiohjain paperin leveyteen. a 5 b Aseta kasetti. jatka toimintoja noudattamalla näytössä • Seuraavaksi näkyviä ohjeita. Näiden toimintojen aikana teet valintoja, jotka liittyvät tietojen lähettämiseen. Lue "Tietojen lähettäminen Canonille" kohdasta Turvallisuus ja tärkeitä tietoja.
Tulostimen asennus Mitä laitetta olet yhdistämässä? Valitse laite ja valitse vastaava ohjeen osa. Tietokone Tietokone ja älypuhelin Älypuhelin Ei laitetta 6-b sivu 6 6-a Napauta Pysäytä (Stop) -painiketta ja valitse sitten Älä yhdistä (Do not connect) > Kyllä (Yes) tässä järjestyksessä. Yhdistäminen tietokoneeseen Jos käytät useita tietokoneita, suorita nämä vaiheet jokaiselle tietokoneelle. Tapoja on kaksi, " Online-asennus" ja " Käyttäen mukana toimitettua Asennus-CD-levyä (vain Windows)".
Käyttäen mukana toimitettua Asennus-CD-levyä (vain Windows) 1 Aseta Asennus-CD tietokoneeseen. 2 Toimi Windows-versiosi ohjeiden mukaan. Windows 7 a Valitse Suorita Msetup4.exe (Run Msetup4.exe). Automaattinen toisto • Kun (AutoPlay)-näyttö tulee näkyviin, Windows 10/Windows 8.1 valitse Suorita Msetup4.exe (Run Msetup4.exe). a Napsauta seuraavaa ilmoitusta, kun se tulee tietokoneen näytön oikeaan reunaan.
Tulostimen asennus 6-b Yhdistäminen älypuhelimeen Jos käytät useita älypuhelimia, suorita nämä vaiheet jokaiselle älypuhelimelle. Valmistele seuraavat, ennen kuin aloitat. a Ota Wi-Fi-asetus käyttöön älypuhelimessa*. b Yhdistä älypuhelin langattomaan reitittimeen* (jos käytössäsi on langaton reititin). * Katso näihin toimenpiteisiin liittyviä lisätietoja älypuhelimen ja langattoman reitittimen käyttöoppaista. 1 Asenna "Canon PRINT Inkjet/SELPHY" -sovellus älypuhelimeen.
Toimenpiteet ovat erilaiset iOS- ja Android-laitteille. Toimi käyttöjärjestelmää vastaavien ohjeiden mukaan. 3 Napauta Asetukset (Settings) älypuhelimen aloitusnäytössä ja napauta Canon_ij_XXXX Wi-Fi-asetuksissa. Huomautus Jos Canon_ij_XXXX ei ole näkyvissä, toimi kohdan mukaan ja hae sitten Canon_ij_XXXX uudelleen. 4 5 3 Avaa asennettu sovellus. rekisteröidään • Tulostin käyttöympäristöön parhaiten soveltuvalla yhteystavalla. Huomautus Jos viesti "Yhtään tulostinta ei ole lisätty.
Valokuvapaperin asettaminen Valokuvapaperia voi lisätä ainoastaan takalokeroon. 1 Avaa takalokeron kansi ja laajenna paperituki. 4 Sulje syöttöaukon kansi. 2 Avaa syöttöaukon kansi ja liu'uta oikeanpuoleinen paperiohjain oikeaan reunaan. 5 Avaa käyttöpaneeli ja vedä paperin luovutustaso ulos. asetetun paperin tietojen asettamista • Jatka noudattamalla näytössä näkyviä ohjeita.
RMC (Regulatory Model Code): K10480
Access Online Manual Zugriff auf das Online-Handbuch Accedere al Manuale online Acceso al Manual en línea Läs Onlinehandbok Åbn Online vejledning Accès au Manuel en ligne Online handleiding openen Acesse o Manual On-line Αποκτήστε πρόσβαση στο Εγχειρίδιο Online Gå til Nettbasert manual Online-käyttöopas-oppaan käyttö From your browser À partir de votre navigateur Über Ihren Browser Via de browser Dal browser Do seu navegador Desde su navegador Από το πρόγραμμα περιήγησής σας Från webbläsaren Fra nettleser