Mode d’emploi FRN
Nous vous remercions d’avoir acheté un produit Canon. Le Canon RF50mm F1.2 L USM est un objectif standard à grande ouverture destiné aux appareils photo de la série EOS R. Micrologiciel de l'appareil photo ●● « USM » signifie moteur ultrasonique. Veuillez utiliser la version la plus récente du micrologiciel à l’aide de l’appareil photo en service.
Précautions de sécurité Précautions pour vous assurer que l’appareil photo est utilisé en toute sécurité. Lire attentivement ces précautions. S’assurer que toutes les informations sont prises en compte afin d’éviter les risques et blessures pour l’utilisateur et d’autres personnes. Avertissement Attention Détails concernant les risques pouvant provoquer des dommages matériels. ● N’exposez pas le produit à une chaleur excessive, par exemple, au soleil, dans une voiture.
Précautions générales Précautions de manipulation CAN ICES-3 (B) / NMB-3 (B) ● Cet objectif doit être équipé de ses filtres Canon pour offrir une meilleure étanchéité à la poussière et à l’eau. ● Si l’objectif passe d’un environnement à basse température à un environnement à haute température, de la condensation risque de se déposer sur la surface de l’objectif et sur les pièces internes.
Nomenclature Sélecteur de mode de mise au point (→ 6) Bague de mise au point (→ 6) Monture de parasoleil (→ 8) Filetage de montage du filtre (→ 9) Bague en caoutchouc (→ 5) Bague de commande (→ 7) Sélecteur de plage de distance de mise au point (→ 7) Repère de montage d’objectif (→ 5) Contacts (→ 5) Monture d’objectif (→ 5) ●● Pour plus d’informations, se reporter aux numéros de pages de référence mentionnés entre parenthèses (→ **).
1. Montage et démontage de l’objectif Repère de montage d’objectif Bouton de déverrouillage de l’objectif Capuchon antipoussière Montage de l'objectif Aligner les repères de montage de l’objectif et de l'appareil photo puis tourner l'objectif dans le sens des aiguilles d’une montre jusqu'à ce que vous entendiez un déclic. Démontage de l'objectif Tourner l’objectif dans le sens inverse des aiguilles d’une montre tout en appuyant sur le bouton de déverrouillage de l’objectif de l’appareil photo.
2. Sélection du mode de mise au point Sélecteur de mode de mise au point Bague de mise au point Pour effectuer des prises de vue avec le mode de mise au point automatique (AF), régler le sélecteur de mode de mise au point sur AF. Pour utiliser uniquement une mise au point manuelle (MF), régler le sélecteur de mode de mise au point sur MF et faire la mise au point en tournant la bague de mise au point. ●● Tourner rapidement la bague de mise au point peut entraîner une mise au point différée.
3. Sélection de la plage de distance de mise au point 4. Bague de commande Il est possible d’allouer les fonctions couramment utilisées avec des appareils photos à la bague de commande, tels que les réglages de vitesse d’obturation et d’ouverture. Sélecteur de plage de distance de mise au point La plage des distances de mise au point peut être réglée par un sélecteur. En réglant une plage des distances de mise au point appropriée, la durée effective de la mise au point automatique peut être réduite.
5. Parasoleil Le parasoleil spécialement conçu de l’objectif supprime la lumière indésirable et protège la partie avant de l’objectif de la pluie, de la neige et de la poussière.
6. Filtres (vendus séparément) Vous pouvez fixer les filtres à la fente d’installation du filtre à l’avant de l’objectif. ●● Fixer les filtres Canon (filtre Canon PROTECT, etc.) pour une meilleure étanchéité à la poussière et à l’eau. ●● Vous ne pouvez fixer qu’un seul filtre. ●● Si vous avez besoin d’un filtre polarisant, utilisez le filtre polarisant circulaire Canon PL-C B. ●● Enlever le parasoleil lors du réglage du filtre polarisant. 7.
Fiche technique Distance focale/Ouverture Construction de l'objectif Ouverture minimale Angle de champ Distance min. de mise au point Grandissement max. Champ de vue Diamètre du filtre Diametre max.
CT1-D045-A 0818Ni © CANON INC.