ENGLISH DIGITAL CAMERA © 2004 CANON INC. PRINTED IN JAPAN Camera User Guide CDI-E104-010 XXXXXXX Camera User Guide z Please read the Read This First section (p. 4). z Please also see the Software Starter Guide and the Direct Print User Guide.
Disclaimer z While every effort has been made to ensure that the information contained in this guide is accurate and complete, no liability can be accepted for any errors or omissions. z Canon Inc. reserves the right to change the specifications of the hardware and software described herein at any time without prior notice.
Flowchart and Reference Guides This Guide Shooting with the Camera Software Starter Guide Symbols Used :This mark denotes issues that may affect the camera's operation. :This mark denotes additional topics that complement the basic operating procedures.
Table of Contents Items marked with are lists or charts that summarize camera functions or procedures. Read This First Chapter 1. Preparing the Camera Components Guide. . . . . . . . . . . . . . . . . . . . . . . . . 10 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Installing the Batteries/CF Card . . . . . . . . . . . . . . . 14 Turning the Power On/Off. . . . . . . . . . . . . . . . . . . . 19 Setting the Date/Time. . . . . . . . . . . . . . . . . . . . . . .
Switching between Light Metering Modes . . . . 76 Adjusting the Exposure . . . . . . . . . . . . . . . . . . . . . 78 Adjusting the Tone (White Balance) . . . . . . . . . . . 79 Changing the ISO Speed. . . . . . . . . . . . . . . . . . . . 81 Changing the Photo Effect. . . . . . . . . . . . . . . . . . . 82 Auto Exposure Bracketing (AEB Mode) . . . . . . . . 84 Focus Bracketing (Focus-BKT Mode) . . . . . . . . . . 85 Locking the Exposure Setting (AE Lock) . . . . . . . .
Read This First Please Read Test Shots Before you try to photograph important subjects, we highly recommend that you shoot several trial images to confirm that the camera is operating and being operated correctly. Please note that Canon Inc.
Camera Body Temperature If your camera is used for prolonged periods, the camera body may become warm. Please be aware of this and take care when operating the camera for an extended period. About the LCD Monitor The LCD monitor is produced with extremely highprecision manufacturing techniques. More than 99.99% of the pixels operate to specification. Less than 0.01% of the pixels may occasionally misfire or appear as red or black dots.
Warnings zDo not aim the camera directly into the sun or at other intense light sources which could damage your eyesight. zDo not trigger the flash in close proximity to human or animal eyes. Exposure to the intense light produced by the flash may damage eyesight. In particular, remain at least one meter (39 inches) away from infants when using the flash. zStore this equipment out of the reach of children and infants. Accidental damage to the camera or batteries by a child could result in serious injury.
zRemove the power cord on a regular periodic basis and wipe away the dust and dirt that collects on the plug, the exterior of the power outlet and the surrounding area. In dusty, humid or greasy environments, the dust that collects around the plug over long periods of time may become saturated with humidity and short-circuit, leading to fire. zDo not cut, damage, alter or place heavy items on the power cord.
zExercise due caution when screwing on the separately sold wide converter, tele-converter and conversion lens adapter. If they loosen, fall off and shatter, the glass shards may cause an injury. CAUTIONS zAvoid using, placing or storing the equipment in places subject to strong sunlight or high temperatures, such as the dashboard or trunk (boot of a car. Exposure to intense sunlight and heat may cause the batteries to leak, overheat or explode, resulting in fire, burns or other injuries.
Preventing Malfunctions Avoid Strong Magnetic Fields Never place the camera in close proximity to electric motors or other equipment generating strong electromagnetic fields. Exposure to strong magnetic fields may cause malfunctions or corrupt image data. Avoid Condensation Related Problems Moving the equipment rapidly between hot and cold temperatures may cause condensation (water droplets) to form on its external and internal surfaces.
1. Preparing the Camera Components Guide Neck Strap Mounts Remote Sensor Flash p. 34, 35, 36 Red-eye Reduction Lamp p. 36 Self-timer Lamp p. 49 Tally Lamp p. 53, 65 Lens CF Card Slot Cover p. 15 Battery Cover p. 14, 141 * 10 The following cables are used to connect the camera to a computer or printer.
Attaching the Neck Strap Attach the strap as illustrated. Check that the strap does not come loose from the strap mount when pulled. Perform the same steps on the other side of the camera. Avoid waving the camera about or catching it on other items when suspending it from the strap. Attaching the Lens Cap Fit the lens cap over the lens casing so that it covers the entire lens. Always replace the lens cap after use. Attach the lens cap cord to the strap.
Controls Microphone Diopter Adjustment Dial p. 26 (Self-timer)/ (Continuous) Button p. 49, 52 Viewfinder p. 24, 26 Shutter button p. 28 Zoom Lever Shooting: (Telephoto)/ (Wide Angle) p. 27, 50 Playback: (Zoom in)/ (Zoom out) p. 40 Movie Button p. 53 (Flash) Button p. 35 OFF Button Mode Lever p. 20 MF (Manual Focus) Button p. 95 FUNC. (Function)/ Button p. 43, 61 (Single Image Erase) Omni Selector S(Up) T(Down) W(Left) X(Right) IS (Image Stabilizer) Button p. 29 MENU Button p.
Mode Dial Use the mode dial to switch between the Shooting modes. z : Auto p. 27 The camera automatically selects settings. z Image Zone p. 45 The camera automatically selects settings according to the image composition type. : Portrait : Landscape : Night Scene : Fast Shutter : Slow Shutter : Stitch Assist p. 47 : Movie p. 53 z Creative Zone p. 71 The user selects exposure, aperture or other settings to achieve special effects.
Installing the Batteries/CF Card Install the batteries and the CF card to get ready for shooting. Please use four AA-size alkaline batteries or separately sold nickel metal hydride (NiMH) batteries. When the indicator blinks, the camera is writing, reading, erasing or transmitting an image to or from the card. Do not perform the following or image data may be lost or corrupted: zDo not shake the camera. zDo not turn off the power or open the CF card slot cover or the battery cover.
a b Label CF card Eject Button a Slide the CF card slot cover in the direction of the arrow, and open it. b Insert the CF card with the label facing up, then close the CF card slot cover. z Push the card in until the CF card eject button fully extends. To remove the CF card, push the CF card eject button and pull the card out. zSee CF Cards and Estimated Capacities (Recordable Images) (p. 151). zYou are recommended to use CF cards that have been formatted in your camera (p. 18).
z While it is possible to use AA-size nickel-cadmium batteries, performance is unreliable and their use is not recommended. z Never mix unused and partially used batteries. Always load four fresh (or fully recharged) batteries at the same time. z Be careful to load the batteries with their positive (+) and negative (-) ends in the right direction. z Never mix batteries of different types or from different manufacturers. All four batteries should be identical.
Battery Status Indications The following icons or messages indicate the battery status on the LCD monitor (or viewfinder). Change the batteries Batteries are beginning to run low. Replace or recharge the batteries if you wish to continue using the camera. Batteries are fully depleted and the camera can no longer operate. You should replace the batteries immediately. CF Card Handling Precautions z CF cards are high-precision electronic devices. Do not bend, force, or subject them to shocks or vibration.
Formatting a CF Card You should always format a new CF card or one from which you wish to erase all images and other data. a c b Please note that formatting (initializing) a CF card erases all data, including protected images and other file types. Please check the contents of the CF card before formatting it. If the camera does not work properly, the inserted CF card may be malfunctioning. Reformatting the CF card may solve the problem.
Turning the Power On/Off a b Indicator a Select [OK] using the W or X arrow on the omni selector, then press the SET button. The indicator blinks red and formatting starts. Wait until the indicator goes off. z To cancel instead of erasing, select [Cancel] and press the SET button. b Press the MENU button. The power/mode indicator remains lit while the power of the camera is on. The power/mode indicator indicates the state of the camera as follows.
Switching Between Shooting and Playback a b a Turn the mode lever to (Shooting) or (Playback) while pressing the release button. The power/mode indicator lights orange or green. b Press the OFF button to turn the power off. 20 1. Preparing the Camera You can quickly switch between Shooting mode and Playback mode. This is convenient when you wish to shoot again after checking or deleting an image immediately after it is shot.
Setting the Date/Time The first time the camera power is turned on or whenever the lithium battery charge is low, start from Step . a b Setting the date and time settings does not cause the date/time stamp to appear on images. For printing images with the date on them, refer to the Direct Print User Guide or Software Starter Guide. See Replacing the Date Battery (p. 144). a Turn the power on (p. 19). b Press the MENU button, and then the X arrow on the omni selector. The [ (Set up)] menu appears.
a a a Select [Date/Time] using the S or T arrow on the omni selector, then press the SET button. b a Set the date and time. z Select the item you wish to set using W or X and set its value using the S or T arrow on the omni selector. b Check that the date and time display correctly, press the SET button and press the MENU button. z The date can be set up to the year 2037. 22 1.
Setting the Language a a a b c b b a Turn the power on (p. 19). b Press the MENU button, and then the X arrow on the omni selector. The [ (Set up)] menu appears. z In Playback mode, you can change the language by holding the SET button while you press the JUMP button. This function cannot be used during movie playback or during a printer connection. a Select [Language] using the S or T arrow on the omni selector, then press the SET button.
Using the Viewfinder and the LCD Monitor Pressing the DISPLAY button switches the LCD monitor display mode. Also, closing the LCD monitor causes the viewfinder to display. Shooting Mode : Press the DISPLAY button LCD Monitor Display (No Information) The combined optical zoom and digital zoom factor displays.
{ –*1 {*2 – Detailed Display No Information Shooting Modes Exposure Compensation AE Lock/FE Lock Light Metering Mode White Balance (WB)*4 Drive Mode Icon Information View Function Standard Display Shooting Playback Mode Mode Reference Page Display Contents p. 45, 71 Flash Output { – – – p. 89 Compression { – { { p. 32 Resolution Resolution (Movies) Frame Rate (Movies) Digital Zoom*5 10x 13x 16x 20x 25x 32x Low Battery { – { { p. 32 { – { – p. 32 { – { – p.
Even in the no information display mode, shooting information appears for approximately 6 seconds (shooting information may not appear depending on the camera settings at that time). The camera shake warning icon will appear on the LCD monitor (or viewfinder) in low light conditions while the camera is preparing to shoot. When this icon appears, use one of the following shooting methods. - Set the flash to On or Auto - Set the image stabilizer function to On (p.
Auto Mode 2. Shooting-The Basics a a Wide angle b c b AF Frame Telephoto a Aim the camera at the subject. Seen from the lens side Standard shooting a Turn the mode lever to (Shooting). b Set the mode dial to . c If you are using the LCD monitor, open it. z The LCD monitor can also be rotated.
z The combined use of the digital zoom and optical zoom enables magnified shooting up to approx. 32x (p. 50). The digital zoom cannot be used with some shooting modes (p. 162). Images become coarser the more they are digitally zoomed. a b a Lightly press the shutter button (pressing halfway) to focus. Two beeps will sound when the camera has finished focusing, and the AF frame appears green. z The AF frame will light yellow and the beep will sound one time if the subject is difficult to focus on.
You can change the length of time images show on the LCD monitor after shooting, or set it so they do not show at all (p. 31). Image Stabilizer Function The image stabilizer function allows you to minimize the camera shake effect (blurred images) when you shoot distant subjects that have been magnified or when you shoot in dark conditions. This function's default setting is [On]. z Pressing the IS button switches the function On and Off. When it is set to On, appears.
Reviewing an Image Right after Shooting zCamera shake may not be fully corrected when shooting with slow shutter speeds with such shooting scenes as evening shots. In this case, affix the camera to a tripod. zIf camera shake is too strong, it may not be fully corrected. Mode Dial After a photo is taken, the image displays for two seconds (to change this setting, see page 31).
Changing the Image Display Duration b a a c b Select [Review] using the S or T arrow on the omni selector and select a duration setting using the W or X arrow on the omni selector. Off:Images do not display 2 to 10 sec.:Images appear for the time selected even if the shutter button is released. c Press the MENU button. a Turn the power on (p. 19), and press the MENU button. The [ z You can continue to display the image as long as the shutter button is fully held pressed regardless of the Review setting.
Changing the Resolution and Compression Compression High Quality Mode Dial You can change the resolution, compression (still images) and frame rate (movies, p. 56) settings to suit the purpose of the image you are about to shoot. Still Images Resolution Display Pixels 32 2.
b a c b a Number of shots remaining (Only displayed when the resolution or compression is selected.) a Press the FUNC. button. b Select * (2048 x 1536) using the S or T arrow on the omni selector. * The current setting is displayed. c Select the resolution you wish to set using the W or X arrow on the omni selector, then press the SET button. a Select the compression you wish to set using the W or X arrow on the omni selector, then press the SET button.
Using the Built-in Flash z Types of CF cards and number of shots remaining (p. 151). b Press the FUNC. button and shoot the image. Mode Dial Use the flash according to the guidelines below. The flash operates as shown below when the Flash Pop-up option (p. 64) is set to [Auto]. Auto with red- The flash fires automatically as required by eye reduction the lighting level, and the red-eye reduction lamp fires each time the main flash fires.
When the Flash Pop-up Function is Set to [Off] a Mode Dial You can manually set the flash when Flash Pop-up is set to [Off]. a Press the button to switch between flash modes and shoot the image. The selected flash mode appears on the LCD monitor (or viewfinder). z You can switch between settings by pressing the button. The flash setting may not switch with certain shooting modes. Flash is open ( ) Flash is closed ( ) a The flash always fires. The flash does not fire.
Setting the Red-eye Reduction Function Mode Dial The red-eye reduction lamp fire when the flash is used in dark areas. This reduces light reflecting back from the eyes and making them appear red. b a c b Select [Red-eye] using the S or T arrow on the omni selector. c Select [On] using the W or X arrow on the omni selector and press the MENU button. appears on the LCD monitor (or viewfinder) if it is set to Information View display.
a b c a Power the camera in (Shooting) mode (p. 19) and press the MENU button. The [ (Rec.)] menu appears. b Select [Slow Synchro] using the S or T arrow on the omni selector. c Select [On] using the W or X arrow on the omni selector and press the MENU button. When shooting with a high ISO sensitivity and using the built-in flash, there is more of a chance of overexposure the closer you are to the subject. The flash fires with automatic adjustments when [Flash Adjust] is set to [Auto] in the Rec.
The flash may take up to approximately 10 seconds to charge in some cases. Actual times will vary according to usage and the battery charge. The flash exposure and the flash output can be changed (p. 89). When shooting with [Slow Synchro] set to [On], camera shake may become a factor. We recommend the use of a tripod. The flash setting is saved when the camera is turned off in the , , and shooting modes. 38 2.
Displaying Images Individually b a a Turn the mode lever to the right to set the camera to Playback mode. 3. Playback-The Basics z When you press the W or X arrow on the omni selector after having pressed the JUMP button, the camera jumps 10 images behind or ahead. If you press the JUMP button once more, the camera returns to the single image playback screen. z Press the DISPLAY button to show the data for the displayed image (p. 24). z Press the button to quickly deleted the displayed image (p. 43).
Magnifying Images b a Magnified approximately 5 times Magnified approximately 10 times Approximate position Approximate position a Turn the mode lever to the right to set the camera to Playback mode. b Turn the zoom lever toward to magnify the image and toward to cancel the magnified display. z In single image playback, images can be magnified up to 10 times. Hold the SET button down and turn the zoom lever toward to cycle through each setting, approximately 2.
Viewing Images in Sets of Nine (Index Playback) b a b a Pressing the S arrow in this row displays the previous set of nine images. Movie Frame a Turn the mode lever to the right to set the camera to Playback mode. b Turn the zoom lever toward . z Nine images appear at once (index playback). Pressing the T arrow in this row displays the next set of nine images. a Change the image selection using the W, X, S or T arrow on the omni selector.
JUMP Jumping Between Images a c b z Index Playback: The previous or next 9 images are displayed. c Press the JUMP button. The jump bar disappears and the camera reverts to single image playback or index playback. Jump Bar a Press the JUMP button while in single image playback (p. 39) or index playback (p. 41). The jump bar appears. b Change the image selection using the W or X arrow on the omni selector. z Single Image Playback: The 10th image ahead or behind is displayed. 42 3.
Erasing Images Individually Please note that erased images cannot be recovered. Exercise caution before erasing a file. b a c 4. Erasing b Select the image you wish to erase using the W or X arrow on the omni selector and press the . c Select [Erase] using the W or X arrow on the omni selector. z To cancel instead of erasing, select [Cancel]. z Protected images cannot be erased with the erase function (p. 106). a Turn the mode lever to the right to set the camera to Playback mode.
Erasing All Images Please note that erased images cannot be recovered. Exercise caution before erasing a file. c Select [OK] using the W or X arrow on the omni selector. z To cancel instead of erasing, select [Cancel]. z Protected images cannot be erased with the erase function (p. 106). b a c a Turn the mode lever to the right to set the camera to Playback mode. The [ (Play)] menu appears. b Select [Erase all] using the S or T arrow on the omni selector. 44 4.
Using the Mode Dial (Image Zone) 5. Useful Shooting Functions Settings fitting the shooting conditions of your subject can easily be set using the mode dial. Landscape Portrait Movie (p. 53) Use this mode to shoot movies. Sound is also recorded simultaneously. Use this mode to shoot spacious landscape scenes. Stitch Assist (p. 47) Use this mode when you want the subject to appear sharp and the background to blur.
z Shooting procedures are the same as for the mode (p. 27). See page 162 for settings that can be changed in this mode. Use the following shooting procedures according to the selected function. a b c d a Turn the mode lever to the left to set the camera to Shooting mode. b Turn the mode dial and set it to the desired function as shown above. c Use the zoom lever to achieve the desired composition (relative to subject size).
Shooting Panoramic Images (Stitch Assist) Use this mode to shoot a series of overlapping frames for merging (stitching) into a large panoramic image using a computer. Please use the bundled PhotoStitch program to merge the images on a computer. Framing a Subject PhotoStitch detects the overlapping portions of adjoining images and merges them. When composing shots, try to include a distinctive item (landmark, etc) in the overlapping portions.
To shoot close-ups, slide the camera over the subject, keeping it parallel as you move. b Shooting Images can be shot in the following 5 sequences in Stitch Assist mode. a Horizontally, left to right Horizontally, right to left Vertically, bottom to top Vertically, top to bottom Clockwise starting at the top left See page 162 for settings that can be changed in this mode. A custom white balance setting (p. 79) cannot be set in mode.
Using the Self-timer Mode Dial a b Sequence Sequence a c a Compose and shoot the second image so that it overlaps the first. z Minor discrepancies in the overlap can be corrected with the software. z An image can be retaken. Press the W, X, S or T arrow on the omni selector to return to that frame. z A maximum of 26 images can be recorded either horizontally or vertically. a Press the button. The current setting is displayed. button cycles between z Pressing the settings.
Digital Zoom z You can switch between the and options through the [ (Rec.)] menu (p. 64). z When the self-timer is set to ( ), the shutter activates 10 (2) seconds after the shutter button is pressed fully. b Check that or shoot the image. is displayed and z When is selected, the self-timer sounds and the self-timer lamp starts blinking when the shutter button is pressed all the way. The selftimer sound and the blinking get faster two seconds before the shutter activates.
c d d Turn the zoom lever toward shoot the image. and b a Turn the mode dial to any Shooting mode except for or . b Press the MENU button to display the [ (Rec.)] menu. c Select [Digital Zoom] using the S or T arrow, select [On] using the W or X arrow on the omni selector and press the MENU button. 5.
Continuous Shooting Mode Dial Use this mode to shoot successive frames while the shutter button is fully pressed. The interval between frames may lengthen somewhat when the internal memory becomes full. The flash can be used, but the interval between images will lengthen to accommodate the flash recharge time. a a Press the b Select 52 5. Useful Shooting Functions button. The current setting is displayed. button cycles between z Pressing the settings. .
Movie Mode a b b a a Press the shutter button halfway to lock the focus. b Press the shutter button all the way to shoot. z Shooting will stop when the shutter button is released. z The shooting speed is 1.7 shots/second.* * Large/Fine (These figures reflect Canon's testing standard. The actual figures will vary according to the shooting conditions and settings.) a Turn the mode dial to . The maximum recording time (in seconds) appears. b Press the Movie button.
z The maximum movie recordable time in one movie shooting is approx. 1 hour and the maximum recording capacity is 1 GB. These figures will vary according to the type of CF cards and their capacity. When recording time reaches 1 hour, when the CF card is about to become full or when the file size is about to reach 1 GB, the remaining shooting time displayed on the lower right corner of the LCD monitor (or viewfinder) will blink red and recording will stop automatically approximately 10 seconds later.
zThe recording time may not display properly during shooting or filming may stop unexpectedly with the following types of CF cards. - Slow recording cards - Cards formatted on a different camera or a computer - Cards which have had images recorded and erased repeatedly Although the recording time may not display properly during shooting, the movie will be recorded correctly on the CF card. Recording time will display properly if you format the CF card in this camera (excluding slow recording CF cards).
QuickTime 3.0 or higher is required to play back movie files (AVI/Motion JPEG) on a computer. (QuickTime (for Windows) is bundled on the supplied Digital Camera Solution Disk. On the Macintosh platform, QuickTime 3.0 or later is generally bundled with Mac OS 8.5 or later operating system.) The following operations are available during movie recording: - Zooming (excluding the digital zoom) - AF lock: Press the MF button. appears on the LCD monitor (or viewfinder).
Viewing/Editing Movies * The current setting is displayed. : Shoots 30 frames per second : Shoots 15 frames per second z The number of recordable frames per second varies according to the selected resolution setting (p. 151). z You can shoot the movie right after selecting settings by pressing the Movie button. This screen will appear again once the movie is shot. d Press the FUNC. button then press the Movie button to start shooting.
b a a This mark appears on movie files a Turn the mode lever to the right to set the camera to Playback mode. b Select a movie using the W or X arrow on the omni selector, then press the SET button. 58 5. Useful Shooting Functions Movie Playback Panel a Select a button from the movie playback panel using the W or X arrow on the omni selector, then press the SET button.
Playback Operations ST:Adjusts the volume during playback SET: Pauses playback. Press again to resume playback. When Playback Ends The last frame remains displayed when playback ends. SET: Displays the movie playback panel. Press again to play back the movie again from the first frame. z You may experience frame dropping and audio breakup when playing back a movie on a computer with insufficient system resources. z The volume at which movies play back can also be adjusted in the Play menu.
b Select the range you wish to edit using the W or X arrow. (Play) using the S or T c Select arrow and press the SET button. The temporarily edited movie will start playing. z The movie will stop if you press the SET button while it is playing. d Select (Save) using the S or T arrow and press the SET button. z When (Exit) is selected, the edited movie is not saved and the camera reverts to the screen in Step . e Select [Overwrite] or [New File] using the W or X arrow and press the SET button.
Selecting Menus and Settings 6. Shooting-Advanced Functions Selecting Settings by Pressing the FUNC. Button (Only in Shooting Mode) Select a function item using S or T Exposure Compensation (± 0) p. 78 Select setting contents using W or X Flash Adjust (± 0) p. 89 Flash Output p. 89 Resolution (L) p. 32 White Balance ( ) p. 79 ) p. 32 Compression ( Turn the mode lever to . Press the FUNC. button. Press the S or T arrow to select a function item. ISO Speed ( Photo Effect ( ) p.
Selecting Settings by Pressing the MENU Button Press the MENU button. Press the W or X arrow to switch between menu tabs. Press the S or T arrow to select a menu item. (Depending on the function, press the SET button after making a selection.) Press the W or X arrow to select setting contents. (Depending on the function, press the SET button after making a selection.) Press the MENU button. Shooting Playback Rec. Menu Play Menu Shoot the image if in Shooting mode.
Set up Menu Rec. Menu My Camera Menu Play Menu (p. 111) 6.
Some menu items may not be available for selection according to the shooting mode (p. 162). You can apply a desired image and sound to and in the My Camera menu. For details, see Registering the My Camera Settings (p. 111) or the Software Starter Guide. Camera settings can be reset to the default values (p. 68). Rec. Menu Menu Item Flash Sync Slow Synchro Flash Adjust Red-eye Flash Pop-up Self-timer Wireless Delay 64 6.
Menu Item Spot AE Point MF-Point Zoom AF Mode Tally Lamp Digital Zoom Review Reverse Disp. Setting content Sets the option of [Spot AE Point] (one of the light metering modes) to Center (the AE point is fixed to the center) or AE Point (the AE point corresponds to the AF point). Center*/AF Point Sets whether or not the focusing point is magnified when using the manual focus. On*/Off Sets the frequency of autofocus activation.
Setting content Reference Page Specifies images before downloading to a computer. p. 126 Menu Item Transfer Order Set up Menu Menu Item Setting content Set [On] to mute the start-up sound, operation sound, selftimer sound and shutter sound all at once. zIf you set [Mute] to [On], no sound will be heard even when any sound Mute item in the My Camera menu is set to , or (On). zNote that the error warning signal beeps even when the Mute setting is [On].
Menu Item Auto Rotate Distance Units Language Video System * Default setting Setting content Sets whether or not images shot with the camera on end are automatically rotated in the display. On/Off* Sets the format of the displayed distance units of the MF indicator. m/cm* or ft/in Sets the language used in the menus and messages on the LCD monitor (or in the viewfinder).
Resetting the Settings to Default Menu Item My Camera menu settings content Setting content (Off)/ */ / Reference Page You can reset the menu and button operation settings to default. – 1 3 2 3 * Default setting 1 Turn the mode lever to power up the camera. or to 2 Press the MENU button for longer than 5 seconds. The message "Reset settings to default?" appears on the LCD monitor (or viewfinder). 3 Select [OK] using the W or X arrow on the omni selector, then press the SET button.
Registering Settings to the Shortcut Button z The normal screen resumes when resetting is complete. z To cancel resetting, select [Cancel] instead of [OK]. zThe following settings cannot be reset to default: - The [Date/Time], [Language] and [Video System] options in the [ (Set up)] menu (p. 66, 67) - White balance data set with the custom white balance function (p. 79) - Newly registered My Camera settings zSettings cannot be reset when the camera is connected to a computer or printer.
Registering a Function 1 Select [Set shortcut button] from the [ (Rec.)] menu and press the SET button. z See Selecting Menus and Settings (p. 62). 2 Select the function you wish to register using the W or X arrow. 70 6.
Using the Mode Dial (Creative Zone) Using the Shortcut Button Mode Dial 1 1 Press the Button. The registered function is recalled and its icon appears on the LCD monitor or viewfinder (except if the display is off). z Pressing the button cycles between setting values of the registered functions. z Functions that are not available in the current shooting mode will not appear even if they are selected. Change the shooting mode setting and press the button again.
2 Turn the mode dial, z In , or , the combinations of shutter speeds and aperture values can be changed within the same exposure setting (p. 73). select the function you wish to use and shoot the image. z The camera operates in the following ways according to the selected function: P Tv Av M Shutter Speed Aperture value The camera automatically sets the shutter speed and aperture value. The user selects a shutter speed using the W or X arrow. The user selects an aperture value using the W or X arrow.
Differences between the and Modes. The following settings can be adjusted in but not in mode.
Shutter Speed Display The numbers in the table below indicate the shutter speed in seconds. 1/160 indicates 1/160 second. Also, quote marks indicate the decimal place, so that 0"3 indicates 0.3 second and 2" indicates 2 seconds.
Selecting an AF Frame z The brightness of the LCD monitor (or viewfinder) matches the selected shutter speed and aperture value. When you select a fast shutter speed or shoot a subject in a dark place and set the flash to (Flash On (red-eye reduction) or (flash On) the image will always be bright. z When you press the shutter button halfway, the difference between the standard exposure* and the selected exposure appears on the LCD monitor (or viewfinder).
2 Move the AF frame to the desired area using the S, T, W or X arrow, then press the button. z You can immediately shoot the image using the selected AF frame by pressing the shutter button instead of pressing the button. z The AF frame will move back to its original position (Center) if you hold down the button. For an explanation of the AF frame colors, please refer to page 24. The AF frame is locked to center-point when using the digital zoom.
1 3 2, 3 1 Press the button to select a metering mode. z Each press of the button changes the metering mode as follows. (Evaluative) (Center-Weighted Averaging) (Spot AE Point) 2 In the [ (Rec.)] menu, select [Spot AE Point]. z See Selecting Menus and Settings (p. 62). 3 Select [Center] or [AF Point] using the W or X arrow, then press the MENU button. e.g.
Adjusting the Exposure Mode Dial Adjust the exposure compensation setting to avoid making the subject too dark when it is backlit or shot against a bright background. z The settings can be adjusted in 1/3-stops in the range of -2EV to +2EV. z You can shoot the image right after selecting settings by pressing the shutter button. This screen will appear again, once the image is shot. 3 Press the FUNC. button. z To cancel the exposure compensation, return the setting to using the W or X arrow.
Adjusting the Tone (White Balance) Mode Dial When the white balance mode is set to match the light source, the camera reproduces colors more accurately. Combinations of setting contents and light source are as follows.
Setting a Custom White Balance In the following cases, the white balance may not be correctly adjusted. Use (Custom) to adjust the white balance. z Shooting subjects of monotone color (such as sky, sea or forest) z Shooting with a peculiar source of light (such as a mercury-vapor lamp) 1, 4 2 3 1 Press the FUNC. button. 2 Select * (Auto) using the S or T arrow and select (Custom) using the W or X arrow. * The current setting is displayed. 80 6.
Changing the ISO Speed - The zoom is positioned to the telephoto end setting. Set the digital zoom to [Off]. - A mode other than is selected. In mode, white balance data cannot be read. - The flash is set to (Flash On) or (Flash Off). Use the same flash setting as the one that will be used for shooting when you set the white balance. If the white balance setting conditions and shooting conditions are not the same, the correct white balance may not be obtained.
2 Select * (ISO Speed) using the S or T arrow and select the desired setting using the W or X arrow. Changing the Photo Effect Mode Dial You can shoot with different saturation and contrast color effects. Photo Effect Off * The current setting is displayed. z You can shoot the image right after selecting settings by pressing the shutter button. The menu displays again after the shot, allowing you to change the settings easily. Vivid Neutral Low Sharpening 3 Press the FUNC. button.
2 1, 3 1 Press the FUNC. button. 2 Select * (Effect Off) using the S or T arrow and select the desired setting using the W or X arrow. * The current setting is displayed. When is selected z A screen allowing you to set the contrast, sharpness and color saturation appears when you press the SET button. Select the item you wish to set using the S or T arrow, set it using the W or X arrow and press the SET button. z You can shoot the image right after selecting settings by pressing the shutter button.
Auto Exposure Bracketing (AEB Mode) 2 Select Mode Dial In this mode, the camera automatically changes the exposure within a set range to take three shots after you press the shutter button once. You can adjust AEB settings in 1/3 stops within the range of -2EV to +2EV of the standard exposure setting. AEB settings can be combined with exposure compensation settings (p. 78) to extend the adjustment range. The images are recorded in the following order: Standard exposure, underexposure and overexposure.
Focus Bracketing (Focus-BKT Mode) 2 Select Mode Dial You can shoot three images while the focus changes automatically when shooting with the manual focus. Three ranges -small, medium or large- can be selected. Images are shot with the focus position changing in the following order; current position, backwards and forward. 2, 3 1, 4 1 Press the FUNC. button. * (BKT-Off) using the S or T arrow, select (Focus-BKT) using the W or X arrow and press the SET button. * The current setting is displayed.
Locking the Exposure Setting (AE Lock) 2 While pressing the Mode Dial You can set the exposure and focus separately. This is effective when the contrast is too strong between the subject and background or when a subject is backlit. 1, 2 shutter button halfway, press the button. z The exposure setting AE lock locks (AE Lock) and the icon appears on the LCD monitor (or viewfinder). z Pressing the button again cancels the AE lock. 3 Recompose the image and shoot.
Locking the Flash Exposure Setting (FE Lock) 3.Press the button. The exposure setting will lock and the icon will appear in the LCD monitor (or viewfinder). 4.Press the W or X arrow until the desired shutter speed or aperture value is reached. 5.Recompose the image and shoot. The setting will cancel after the shot is taken. Mode Dial You can obtain the correct exposure regardless of the location of your subject in the composition. 1 2 3 1 Press the button and set the flash to fire (p. 34).
3 While pressing the shutter button halfway, press the button. z The flash exposure compensation setting locks (FE Lock) and the icon appears on the LCD monitor (or viewfinder). z The flash will fire a pre-flash and lock the flash exposure to the required intensity to illuminate the subject. z Each time you press the button, the flash exposure locks at the required intensity for that composition. z Using any button or lever other than the omni selector cancels the FE lock.
Setting the Flash Adjustment/Flash Output Mode Dial *1 *2 When [Flash Adjust] is set to [Manual], flash output settings can be made. [Flash Output] can be set. Flash Adjust Flash Output zWhen [Flash Adjust] is set to [Auto], settings can be adjusted in 1/3-stop increments in the range of -2EV to +2EV. zYou can enjoy flash photography with exposure adjustments with the combined use of the camera’s exposure compensation function.
Switching the Timing at which the Flash Fires Mode Dial The flash fires right after the shutter opens, regardless of the shutter speed. Usually, the 1stcurtain is used when shooting. The flash fires right before the shutter closes, regardless of the shutter speed. Compared with the 2nd-curtain 1st-curtain, the flash fires later and this allows you to shoot images in which, for example, a car's rear lamps seem to trail off behind. 2 1 1st-curtain 1 From the [ (Rec.)] menu, select [Flash Sync].
Shooting Images at Set Intervals (Intervalometer) 1 Select [Intervalometer] Mode Dial You can shoot images at a set interval. This function can be used for fixed-point observation of plants and blooming flowers. The shooting interval time can be set from 1 to 60 minutes and 2 to 100 images can be shot. Since the camera may shoot continuously for an extended period of time, the use of the Compact Power Adapter CA-PS700 (sold separately) is recommended (p. 143). 5 2, 3 1 1, 4 from the [ (Rec.
4 Press the SET button. z The camera exits the menu screen and Int. appears at the lower right of the LCD monitor (or viewfinder). 5 Press the shutter button. z The first image is shot and the interval shooting session starts. z Once the set number of shots is taken the camera automatically powers down regardless of the power saving function settings. z If the below operations are accessed while the interval shooting is in process, the interval shooting session will be canceled.
Shooting Problem Subjects for the Autofocus The autofocus may not work well on the following types of subjects.
Shooting in AF Lock Mode z Pressing the MF button a second time cancels the manual focus mode. 3 Recompose the image and press the Mode Dial 2, 3 2 1 Aim the AF frame at an object at a similar distance to the subject you wish to shoot. 2 Press the shutter button halfway and while keeping it pressed, press the MF button. z appears on the LCD monitor (or viewfinder). z The focus will stay locked even if you release the shutter button and MF button. 94 6.
Shooting in Manual Focus Mode Mode Dial The focus can be manually set. 1 2 1 2 Press the shutter button all the way 1 Press and hold the to shoot the image. MF button, then press the S or T arrow. z The focus will lock and the icon and the MF indicator will appear on the LCD monitor (or viewfinder). z When the [ (Rec.)] menu's [MF-Point Zoom] is set to [On], if a particular AF frame has been manually selected (p. 75), the portion of the image in that frame will appear magnified.
3 Press the shutter button all the way Using the Manual Focus in Combination with the Auto Focus to shoot the image. Mode Dial The camera automatically searches for a more suitable focusing point from the current manually focused location. 1 1 2 1 Focus the camera with the manual focus. 2 Press the SET button. z The camera focuses automatically to a more accurate focusing point near the current focusing point. 96 6.
Switching between Focus Settings Mode Dial You can switch between focus settings to shoot. Continuous Single The camera is continually focusing on whatever it is aimed even when the shutter button is not pressed, allowing you to shoot without missing opportunities. This is the default setting. The camera only focuses when the shutter button is pressed halfway, conserving battery power. 2 1, 2 1 In the [ (Rec.)] menu, select [AF Mode]. z See Selecting Menus and Settings (p. 62).
Saving Custom Settings Mode Dial 1 You can save frequently used shooting modes and various shooting settings to the (Custom) mode. When necessary, you can then shoot images with previously saved settings by simply turning the mode dial to . Settings that are usually forgotten when the shooting mode is changed or when the power is turned off (such as Continuous Shooting and Self-timer mode) are also remembered. 3, 4 3, 5 1 Turn the mode dial to or .
3 Select [Save Settings] from the [ (Rec.)] menu and press the SET button. z See Selecting Menus and Settings (p. 62). 4 Select [OK] and press the SET button. 5 Press the MENU button. The setting contents do not influence other shooting modes. Saved settings can be reset (p. 68). 6.
7. Playback-Advanced Functions Rotating Images in the Display Images can be rotated 90° and 270° clockwise on the LCD monitor. Original 90° 270° 2 Select an image you want to rotate using the W or X arrow and press the SET button. z The image cycles to the next orientation (90° 270° original) each time the SET button is pressed. 3 Press the MENU button. 2 2 1, 3 1 Select [Rotate] from the [ (Play)] menu and press the SET button. z See Selecting Menus and Settings (p. 62). 100 7.
Attaching Sound Memos to Images In Playback mode (including single image playback, index playback, magnified playback and the review immediately after shooting in Shooting mode) you can attach sound memos (up to 60 seconds) to an image. The sound data is saved in WAVE format. 2 2 1 1 Press the button while playing back images. z The Sound Memo panel appears. 2 Select using the W or X arrow and press the SET button. z The recording starts and the elapsed time is displayed.
Automated Playback (Slide Show) zYou cannot attach sound memos to movies. zYou cannot record or playback sound notes for images that already have an incompatible sound file attached. If you attempt to record or play such images, the "Incompatible WAVE format" message will display. Incompatible sound files can be deleted with this camera. zSound memos for protected images cannot be erased (p. 106). Slide show image settings are based on DPOF standards (p. 119).
2 Select [Program] using the S or T arrow and select between [All images] or one of [Show 1][Show 3] using the W or X arrow. 3 Select [Start] using the S or T arrow and press the SET button. The show will start and automatically stop when the show is done. Pausing and Resuming a Slide Show z Press the SET button to pause the show. Press it again to resume. Fast Forward/Rewinding a Slide Show z User the W or X arrow to move to the previous or next image.
2 Select [Program] using the S or T arrow and select [Show 1], [Show 2] or [Show 3] using the W or X arrow. z A checkmark (3 3) will appear beside a show already containing images. 3 Choose [Select] using the T and W or X arrows and press the SET button. 4 Mark images to include in the show. Single Image Playback z Move between images using the W or X arrow and mark or remove marks from images using the S or T arrow. z The selection number and a check mark (3 3) appear at the bottom of selected images.
Adjusting the Play Time and Repeat Settings Play Time Repeat Sets the duration that each image in a slide show is displayed. The options are any one of 3-10 seconds, 15 seconds, 30 seconds and Manual. Sets whether the slide show stops when all the slides have been displayed or continues to display until stopped. 2, 3, 4 2 1, 5 1 Display the slide show menu (p. 102). 2 Select [Set up] using 4 Select a setting using the W or X arrow. Play time z Select a play time. Repeat z Select [On] or [Off].
Protecting Images You can protect important images from accidental erasure. 2 1, 2 1, 3 1 In the [ (Play)] menu, select [Protect] and press the SET button. z See Selecting Menus and Settings (p. 62). 2 Select an image you want to protect using the W or X arrow and press the SET button. 106 7. Playback-Advanced Functions z The icon appears on protected images. z To remove the protection, press the SET button again (in protection mode).
Setting the Power Saving Function This camera is equipped with a power saving function. Depending on the power saving setting, the camera may power down or the LCD monitor (or viewfinder) may go off automatically. z Auto Power Down [On]: zShooting mode Powers down approximately 3 minutes after the last time a camera control is accessed. The LCD monitor (or viewfinder) automatically shuts off approximately 1 minute*1 after the last time a camera control is accessed even if [Auto Power Down] is set to [Off].
Setting the Auto Rotate Function Mode Dial 1 Select [Power Saving] 2, 3 1 1, 4 This camera is equipped with an Intelligent Orientation sensor that detects the orientation of an image shot with the camera on end and automatically rotates it to the correct viewing orientation in the display. You can set this function on/off. in the [ (Set up)] menu and press the SET button. 2 1, 2 z See Selecting Menus and Settings (p. 62).
2 Select [On] using the W or X arrow and press the MENU button. z When this function is On, an icon showing the orientation of the camera appears at the upper right corner of the LCD monitor (or viewfinder) if it is set to Information View. : Normal : Camera on right end : Camera on left end zThis function may not operate correctly when the camera is pointed straight up or down. Check that the correct camera orientation icon (e.g. ) is displayed and if it is not, then set the Auto Rotate function to Off.
Resetting the File Numbers You can select the way file numbers are assigned. On Off The file numbers are reset to the start (100-001) each time a new CF card is inserted. New images recorded on CF cards with existing files are assigned the next available number. The file number of the last image to be shot is memorized so that images recorded to a new CF card start from the next number. 2 1, 2 1 In the [ (Set up)] menu, select [File No. Reset]. z See Selecting Menus and Settings (p. 62). 110 8.
Customizing the Camera (My Camera Settings) My Camera allows you to customize the startup image and start-up, shutter, operation and self-timer sounds. Each menu item has three choices. Changing My Camera Settings 1, 2 1, 3 1 Press the MENU button and press the X arrow twice. The [ (My Camera)] menu appears. 2 Select a menu item using the S or T arrow, then select setting content using the W or X arrow. : Off : General : Science fiction theme : Animal theme z The contents of the and changed (p. 67).
Registering My Camera Settings This function registers new contents to the and options. Images recorded onto the CF card and newly recorded sounds can be added to the camera. You can also use the supplied software to upload your computer's images and sounds to the camera. The following menu items can be saved to the camera. · Start-up Image · Operation Sound · Shutter Sound · Start-up Sound · Selftimer Sound The CF card images and sounds can be registered to the camera with the following procedures.
Registering a Start-up Image z Select the image you wish to register using the W or X arrow and press the SET button. Registering Start-up, Operation, Self-timer and Shutter Sounds z Select (Record) using the W or X arrow and press the SET button. z Recording will start and automatically stop when the time is exceeded. Start-up Sound: 1 sec. Self-timer Sound: 2 sec. z Select Operation Sound: 0.3 sec. Shutter Sound: 0.3 sec. (Register) and press the SET button.
- Recording time Start-up Sound Operation Sound Selftimer Sound Shutter Sound 11.025 kHz 1.0 sec. or less 0.3 sec. or less 2.0 sec. or less 0.3 sec. or less 8.000 kHz 1.3 sec. or less 0.4 sec. or less 2.0 sec. or less 0.4 sec. or less Any file format other than those described above cannot be used with this camera. An example of this function is to record "Say cheese" as a self-timer sound so the camera will play back this sound 2 seconds before the photo is taken.
Downloading Images to a Computer Download images taken with the camera to a computer in one of the following ways: Connect the camera to a computer with the USB cable You can then download images directly from the camera to a computer. Directly from the CF card Using a card adapter or a card reader, you can download images directly from the CF card. After the software is installed, you can use it to easily download images and print them or send them by email.
2 Connect the supplied interface cable to the computer's USB port and the camera's DIGITAL terminal. z To disconnect the cable from the camera: Hold the cable connector firmly at both sides and pull it straight out. USB port Interface cable DIGITAL Terminal a Open the terminal cover with your fingernail. b Hold the USB connector so the side is up, then insert it into the DIGITAL terminal securely. aDIGITAL terminal cover bInterface cable 116 9.
Downloading Directly from a CF Card Downloading Images without Installing the Software (Windows XP and Mac OS X (v10.1 or v10.2) only) If you are using Windows XP or Mac OS X (v10.1 or v10.2), you can use the software distributed with these operating systems to download images (JPEG format only) without installing the software bundled on the Canon Digital Camera Solution Disk. This is useful for downloading images to a computer in which the software is not installed.
3 Copy images from the card into a folder of your choice on the hard disk. z The images are stored in the [xxxCANON] folders located under the [DCIM] folder (where xxx is a three-digit number from 100 to 998) (p. 155). Viewing Images on a TV Set A video-compatible television connected via the supplied AV cable AVC-DC300 can be used to view images as you shoot or play back them. 1 Turn off the camera (p. 19) and the TV. 2 Attach the AV cable to the A/V OUT terminal on the camera.
4 Turn on the TV and switch it to Video mode. 5 Power the camera into Shooting mode or Playback mode (p. 19). z The image will appear on the TV. Shoot or play back images as usual. No image will appear on the LCD monitor (or viewfinder) when the camera is connected to a TV monitor. The video output signal can be switched (NTSC or PAL) to accommodate different regional standards. The default setting will vary between regions. NTSC:Japan, U.S.A., Canada, Taiwan, etc.
Print settings (DPOF Print Settings) (p. 121) Image Transmission Settings (DPOF Transfer Order) (p. 126) Direct Print Compatible Printers Direct Print Compatible Printing - For details, see the Direct Print user Guide. - Also, refer to your printer's manual. Photo Lab zCP Printer zBubble Jet Printer zNon-Canon PictBridge compliant printers 120 9.
Print Settings (DPOF Print Settings) You can select images on a CF card for printing and specify the number of print copies in advance using the camera. This is extremely convenient for sending the images to a photo developing service or for printing on a direct print function compatible printer. Refer to the Direct Print User Guide for instructions on how to select print settings from the printer. zThe mark may appear on images that have had print marks set by another DPOF compliant camera.
3 Select images for printing. Single Images Number of copies z When the print type (p. 123) is set to [Standard] or [Both], select an image using the W or X arrow. You can set the number of copies (up to 99) to be printed using the S or T arrow. z When the print type (p. 123) is set to [Index], select an image using the W or X arrow and mark or remove marks from images using the S or T arrow. A check mark appears on the marked image.
Images are printed in order from oldest to newest by the shooting date. A maximum of 998 images can be marked per CF card. When [Print Type] is set to [Both], the number of copies can be set. When it is set to [Index], the number of copies cannot be set (only one copy will be printed). Print settings can also be assigned to images with the supplied software programs (ZoomBrowser EX or ImageBrowser) on a computer.
3 Select [Print Type], 2, 3 1, 2 1, 4 1 In the [ (Play)] menu, select [Print Order] and press the SET button. z See Selecting Menus and Settings (p. 62). 2 Select [Set up] using the W or X arrow and press the SET button. 124 9. Additional Features [Date] or [File No.] using the S or T arrow and select settings using the W or X arrow. Print Type z Select [Standard], [Index] or [Both]. Date z Select [On] or [Off]. File No. z Select [On] or [Off]. 4 Press the MENU button.
The date prints as the date and time in the format specified in the Set Date/Time menu (p. 21). Resetting the Print Settings The print settings can all be removed at once. The print type is reset to [Standard] and the date and file number options are set to [Off]. 2 Select [Reset] using the W or X arrow and press the SET button. 3 Select [OK] using the W or X arrow and press the SET button. 2, 3 1, 2, 3 1 1 In the [ (Play)] menu, select [Print Order] and press the SET button.
Image Transmission Settings (DPOF Transfer Order) You can use the camera to specify settings for images before downloading to a computer. Refer to the Software Starter Guide for instructions on how to transfer images to your computer. You cannot use this function to transfer several images at once on Mac OS X computers. The settings used on the camera comply with the Digital Print Order Format (DPOF) standards. The mark may appear on images that have had transfer marks set by another DPOF compliant camera.
3 Select images for transferring. Single Images z Select an images using the W or X arrow and mark or remove marks from images using the S or T arrow. A check mark (3 3) appears on the marked image. z You can use the same procedures to select images in index playback (3 images). Turn the zoom lever toward to switch between single image playback and index playback. z You can select images using the W or X arrow and change the settings using the S or T arrow after [Mark all] or [Clear all] has been selected.
Appendix List of Messages The following messages may appear on the LCD monitor (or viewfinder). z For messages which may appear when a printer is connected, refer to the Direct Print User Guide. Busy... Image is being recorded to, or read from, CF card. Resetting all the camera and menu settings to default No memory card You attempted to shoot or play back images without a CF card installed. Cannot record! You attempted to shoot an image without a CF card installed.
Cannot rotate You attempted to rotate a movie or an image that was photographed with another camera, recorded in a different format, or edited on a computer. Unidentified Image You attempted to play back an image that was recorded in a special format (proprietary format used by the camera of another manufacturer, etc.) or a movie clip recorded by another camera. Incompatible WAVE format Cannot attach sound memos to the image because the image has some sound file recorded in an inappropriate format.
Troubleshooting Problem Cause Camera will not operate Power is not turned on. CF card slot cover or battery cover opened. Batteries are loaded in the wrong direction. Insufficient battery voltage. Batteries are not the right type. Camera will not record 130 Appendix Poor contact between camera and battery terminals. Camera is in Playback or computer/printer connection mode. Solution Turn on the camera. See Turning the Power On/Off (p.
Problem Cannot play back Lens will not retract Batteries consumed quickly Cause Solution You attempted to play back images shot with Computer images that cannot be played back will play back if they another camera or images edited on a computer. are added to the camera using the bundled software program ZoomBrowser EX or ImageBrowser. See the ZoomBrowser EX/ ImageBrowser Software User Guide (PDF).
Problem Cause If using rechargeable Batteries were placed in the charger in the batteries: Batteries do wrong direction. not charge in separately Poor electrical contact. sold battery charger. Image is blurred or out of focus Battery terminals are dirty. Battery life exceeded. Camera moved. Subject out of focal range. Subject is hard to focus on. 132 Appendix Solution Put batteries back into the charger in the correct direction. zBe sure to set batteries firmly into the charger.
Problem Subject in recorded image is too dark Cause Insufficient light for shooting. Subject dark in comparison to the background. Solution Set the built-in flash to on. zSet the exposure compensation to a positive (+) setting. zUse the AE lock or spot metering function. See Locking the Exposure Setting (AE Lock) (p. 86) and Switching between Light Metering Modes (p. 76). Subject too far for flash to reach. zTo use the built-in flash, shoot within the following ranges: Auto ISO: 1.0 to 4.2 m (3.
Problem Cause White dots or white Light from the flash has reflected off dust asterisks appear on the particles or insects in the air. This occurs more image frequently in the following conditions: zWhen shooting at the wide angle end. zWhen shooting with a high aperture value in the aperture-priority AE mode. Flash will not fire Flash set to Off. Image not showing on Incorrect video system setting. TV Shooting mode set to (Stitch Assist).
Using the Wireless Controller (Sold Separately) Installing the Battery Install the date battery (CR2025) into the Wireless Controller WL-DC100 (sold separately) before use. Removing the Battery To remove the date battery, pull it in the direction of the arrow. Warning Be particularly careful to keep the date batteries out of the reach of children. Seek medical assistance immediately if a child swallows a battery since corrosive battery fluids could damage the stomach or intestinal wall.
Shooting Playback Press the button on the camera until the or icon appears in the LCD monitor (or viewfinder), then shoot the image. aCompose the image with the zoom ring. bPress the shutter button. The camera will shoot the image after the time set in [Wireless Delay] in the Rec. menu has elapsed (0 seconds, 2 seconds or 10 seconds). zEach press of this button switches the information view mode between No Information and Information View.
Using Conversion Lenses (Sold Separately) Conversion Lens Adapter LA-DC52E and Lens Hood LH-DC20 are included in the separately sold Lens Adapter/Hood Kit LAH-DC10. The camera supports use of the separately sold Wide Converter WC-DC52A and Tele-converter TCDC52B. In order to attach any of these lenses, you also need to use the separately sold Conversion Lens Adapter LA-DC52E (included with LAH-DC10).
Attaching a Lens/Lens Hood 1 Be sure that the camera is turned off. Press the ring release button and hold it down, turn Ring the ring in the Ring Release Button direction of the arrow and remove it. 2 Align the z marks on the conversion lens adapter and the z mark on the camera, and turn the adapter in the direction of the arrows as far as the S mark on the camera. Conversion Lens Adapter LA-DC52E when attached.
zYou should not shoot images in (Stitch Assist) mode when using these attachments. Although it is possible to select this mode on the camera, the PhotoStitch software will not be able to stitch the images together at the computer. zTo protect the conversion lens, hold the camera's lens with one had and screw the conversion lens onto the camera with the other hand. zCompletely remove all dust and dirt from conversion lenses with a lens blower brush before use. The camera may focus on any dirt that remains.
Using the Power Kits (Sold Separately) Using Rechargeable Batteries (Battery and Charger Kit CBK4-200) Included are the battery charger and four rechargeable AA-size NiMH (nickel metal hydride) batteries. Charge batteries as shown below. Charge Indicator zThe charge indicator blinks while charging, then remains lit when charging is finished. zThis charger can be used only to charge Canon AA-size NiMH batteries NB-2AH. Please do not attempt to charge NB-2AH batteries in any other type of charger.
- When charging the batteries (insert and remove the batteries two or three times before charging) - When charging completes in a matter of a few minutes (the battery charger indicator remains lit) zYou may not be able to fully charge the batteries due to their specifications right after purchase or after long periods of non-use. If this happens, use the batteries until their charge is depleted before charging them again. After doing this several times, battery performance will be restored.
It takes approximately 250 minutes for the charger to fully recharge the batteries (as determined by testing at Canon facilities). Please do not charge batteries in areas where the temperature is outside the range of 0 to 35 °C (32 to 95 °F). Charging time varies according to ambient temperature and to the batteries' initial charge state. The battery charger may emit noise while charging. This is not a malfunction. Battery/Charger Kit CBK100 can also be used.
Compact Power Adapter You should use the separately sold Compact Power Adapter CA-PS700 when using the camera for long periods of continuous use or for connecting to a computer or printer. 2 Open the terminal cover and connect the DC plug of the compact power adapter to the camera's DC IN terminal. 1 Attach the power cord to the compact power adapter and plug it into a power outlet. To power outlet z Always disconnect and unplug the compact power adapter after use.
Replacing the Date Battery If the Set Date/Time menu appears when you turn on the camera power, the date battery charge is low and the date and time settings have been lost. Please replace the battery with a commercially available lithium coin battery (CR1220) with the following procedures. 1 Turn off the power 2 Please note that the first date battery may appear to expire relatively quickly after you purchase the camera.
Camera Care and Maintenance Use the following procedures to clean the camera body, lens, viewfinder, LCD monitor and other parts. Camera body Lens Viewfinder LCD Monitor : Wipe the body clean with a soft cloth or eyeglass lens wiper. : First use a lens blower brush to remove dust and dirt, then remove any remaining dirt by wiping the lens lightly with a soft cloth. zNever use synthetic cleansers on the camera body or lens.
Specifications All data is based on Canon's testing standard. Subject to change without notice. PowerShot S1 IS Camera Effective Pixels Image Sensor Lens Digital Zoom Viewfinder LCD Monitor AF System Shooting Distance (from the front of the lens) Shutter Shutter Speeds Light Metering System Exposure Control System Exposure Compensation Sensitivity 146 Appendix Approx. 3.2 million 1/2.7 -inch CCD (Total number of pixels: Approx 3.3 million) 5.8 (W) – 58 (T) mm (35mm film equivalent: 38 - 380 mm) f/2.
White Balance Built-in Flash Flash Range Flash Exposure Compensation Shooting Modes Continuous Shooting Interval Shooting Self-timer Wireless Control PC-controlled Shooting Recording Media File Format TTL auto, pre-set (available settings: Daylight, Cloudy, Tungsten, Fluorescent, Fluorescent H or Flash) or custom Auto*, on*, off * Red-eye reduction is available. 1.0 – 4.2 m (3.3 – 14 ft.) (W), 1.0 – 3.8 m (3.3 – 12 ft.) (T) (When sensitivity is set to ISO 100 equivalent.) ± 2.
Image Recording Format Compression Number of Recording Pixels Frame Rate Audio Data Playback Modes Direct Print Display Languages My Camera Settings Interface 148 Appendix Still images: JPEG (Exif 2.
Power Source Operating Temperature Operating Humidity Dimensions Weight 1. Four AA-size alkaline batteries (included in the camera kit) 2. Four AA-size rechargeable NiMH batteries (NB4-200) (sold separately) 3. Compact Power Adapter (CA-PS700) (sold separately) 0 – 40 °C (32 – 104 °F) 10 – 90 % 111 x 78.0 x 66.1 mm (4.4 x 3.1 x 2.6 in.) (excluding protrusions) Approx. 370 g (13.1 oz.) (camera body only) (W): Wide angle end (T): Telephoto *1 This digital camera supports Exif 2.
Battery Performance Number of Images Shot LCD Monitor on Viewfinder on AA Alkaline Batteries (included with the camera) AA NiMH Battery (NB4-200) * * Playback Time Approx. 120 Approx. 125 Approx. 5 hours 30 min. Approx. 550 Approx. 570 Approx. 7 hours 30 min. The data above reflects standard Canon testing conditions. The actual figures will vary according to the shooting conditions and settings. Movie data is excluded.
CF Cards and Estimated Capacities (Recordable Images) L (Large) 2048 x 1536 pixels M1 (Medium 1) 1600 x 1200 pixels M2 (Medium 2) 1024 x 768 pixels S (Small) 640 x 480 pixels Movie* 640 x 480 pixels (Fine) 640 x 480 pixels 320 x 240 pixels FC-32MH 18 33 67 30 54 108 53 94 174 120 196 337 15 sec./30 sec. 20 sec./42 sec. 46 sec./91 sec.
CompactFlash™ Card Image File Sizes (Estimated) Compression Resolution L M1 M2 S 2048 x 1536 pixels 1600 x 1200 pixels 1024 x 768 pixels 640 x 480 pixels 1602 KB 1002 KB 570 KB 249 KB 445 KB 278 KB 170 KB 84 KB Frame Rate Image Quality 640 x 480 pixels (Fine) Movie 640 x 480 pixels 320 x 240 pixels 893 KB 558 KB 320 KB 150 KB 1980 KB/sec. 1440 KB/sec. 660 KB/sec. 990 KB/sec. 720 KB/sec. 330 KB/sec. Card slot type : Type I Dimensions : 36.4 x 42.8 x 3.3 mm (1.4 x 1.7 x 0.1 in.) Weight : Approx.
Wide Converter WC-DC52A (Sold Separately) Magnification Focal range Lens composition Shooting distance (from the front of the lens) Thread diameter Dimensions Weight : Approx. 0.7 : 26.6 mm (35mm film equivalent) : 3 elements in 3 groups : 0 cm – infinity (0 in. – infinity) : 52 mm standard filter thread Conversion Lens Adapter LA-DC52E is required to attach this lens to the PowerShot S1 IS : Diameter: 81.0 mm (3.2 in.) : Length: 46.0 mm (1.8 in.) : Approx. 145 g (5.12 oz.
Photo Tips and Information ISO Speed (p. 81) Tip for Using the Self-timer (p. 49) The ISO speed is the numeric representation of the camera's sensitivity to light. The higher the ISO speed, the higher the sensitivity. A high ISO speed allows you to shoot images in dark indoor or outdoor conditions without a flash and also helps prevent blurred images due to camera shake. This is convenient when shooting images in places where flash photography is prohibited.
Managing Image Files (p. 110) About File and Folder Numbers Images are assigned file numbers from 0001 to 9900, and folders are assigned folder numbers from 100 to 998 (Folder numbers cannot contain 99 in the last two digits). DCIM 100 CANON 0001 0002 0099 0100 101 CANON 0101 0102 0199 0200 198 CANON 9801 9802 9899 9900 Folder numbers cannot contain 99 in the last two digits. 200 CANON 0001 0002 0099 0100 Folder File Capacity Each folder usually contains up to 100 images.
Overexposure The whole recorded image is bright, which makes black elements of the image appear gray. Shooting dark subjects or in dark places may cause the image to be overexposed. Adjust the exposure compensation towards the - end.
Index Numerics 1st-curtain .............................................................90 2nd-curtain ............................................................90 A Adjusting the Exposure .........................................78 AE Lock .................................................................86 AEB Mode .............................................................84 AF Frame ( ) ..............................................24, 75 AF Lock Mode .................................................
FE Lock ................................................................. 87 File No. Reset ....................................................... 66 File Numbers ...................................................... 110 Flash ........................................................10, 34, 64 Adjustment Settings ....................................... 88 Sync ............................................................... 64 Timing at which the Flash Fires ...................... 90 Focus .................
Microphone ( ) ........................................... 12, 101 Mode Dial ................................................ 13, 45, 71 Mode Lever ...........................................................12 Movie Editing .............................................................57 Recording ( ) ...............................................53 Viewing ...........................................................57 Mute ......................................................................
Shooting Mode ............................................... 20, 24 Shortcut ( ) ...........................................12, 65, 69 Shutter Button ............................................................. 12 Pressing ......................................................... 28 Sound ..................................... 28, 67, 111, 112 Speed ............................................................. 71 Volume ........................................................... 66 Slide Show .............
FCC Notice (Digital Camera, Model PC1058) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules.
Functions Available in Each Shooting Mode This chart shows the functions available in each shooting mode. You can shoot with the settings saved in the mode (p. 98). Ref.
Ref. Page On { { { { { { { – { {* {* – Off – – – – – – – – – { { { 1st-curtain { { { { { – { – {* {* {* {* 2nd-curtain – – – – – { – { { { { { On { { { { { { { – {* {* {* {* Off – – – – – – – – { { { { Single Shot {* {* {* {* {* {* {* {* {* {* {* {* – Standard Continuous Mode – { { { { { – – { { { { p.
Ref. Page – { { { { { U U(2) { { { – Evaluative Metering { { { { { { { { {* {* {* {* Center-Weighted Averaging – – – – – – – – { { { { Spot Metering – – – – – – – – { { { { Center – – – – – – – – {* {* {* {* AF Point – – – – – – – – { { { { – – – – – – – {(3) { { { – p. 86, 87 AEB – – – – – – – – { { { – p. 84 Focus-BKT – – – – – – – – {(1) {(1) {(1) {(1) p.
* Default setting {: Setting selection is possible. U: Setting can only be selected for the first image. –: Setting selection is not possible. : Setting remains in effect even when the camera is turned off. The default for the settings changed by the menu and button operations can be restored all at once except for [Date/Time], [Language] and [Video System] (p. 68). (1) Selectable only in manual focus. (2) Can be set after AE lock is set. (3) AE lock only is available.