BUBBLE JET PRINTER Quick Start Guide Table of Contents Preface 1 Shipping Materials 1 Introduction 1 Printer Parts and Their Functions Setting Up Preparing the Printer 2 4 4 Connecting the Printer to the Computer 4 Installing the Print Head 6 Loading Paper 9 Installing the Printer Driver 10 Aligning the Print Head 16 Basic Operations 22 Printing with Windows 22 Printing with Macintosh 24 Printing Without Using the Computer 26 Before Printing 26 Printing Photographs 31 Print App
Exif Print This printer supports Exif 2.2 (also called “Exif Print”). Exif Print is a standard for enhancing the communication between digital cameras and printers. By connecting to an Exif Print-compliant digital camera, the camera’s image data at the time of shooting is used and optimized, yielding extremely high quality prints.
Preface ■■ Shipping Materials ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ Thank you for purchasing a Canon Bubble Jet Printer. Check that all the following items are in the box. If anything is missing or is damaged, contact your Canon Authorised Dealer or Sales Representative.
■■ Printer Parts and Their Functions ■■■■■■■■■■■■■■■■■■■■■ ■ Front View Card Slot Use to connect the PC card adapter. Paper Guide When loading paper, ensure the left edge just touches this guide. To move the paper guide, pinch the knob and slide in the appropriate direction. Indicator lamp Goes on when memory card reading becomes enabled and flashes while the memory card is being read. When this lamp goes off, when the memory card cannot be read. Paper Rest Sheet Feeder Load paper here.
■ Inside the Printer Paper Thickness Lever Adjusts the gap between the print head and the surface of the printing paper. Print Head Holder Install the print head here. Print Head Lock Lever Locks the print head into the holder. Once the print head is installed, do not touch this lever. ■ Operation Panel POWER Button Press to turn the printer on or off. Reset Button Press to resume printing once an error has been cleared. The printer will then initialise ready for printing.
Setting Up ■■ 1 ■ Preparing the Printer ■■■■■■■■■■■■■■■■■■■■■■■■■■■ 1 Place the printer on a flat surface. 2 Remove the packing material and tape from the printer as shown. The tape position may be changed. 3 Attach the paper rest to the sheet feeder. paper rest paper output tray 4 Attach the paper output tray as shown. ■■ 2 ■ Connecting the Printer to the Computer ■■■■■■■■■■■ ➥Note If you are printing with only Direct Print, skip this section and go to “Installing the Print Head” on page 6.
➥Notes • If your computer has an earth connection, ensure that this is attached. • If you do not intend to use the printer for a long period of time, unplug the power cord from the power outlet after turning off the printer. Follow the steps below to install the printer driver correctly. 1 Ensure the printer and the computer are switched off. 2 Connect the cable.
■■ 3 ■ Installing the Print Head ■■■■■■■■■■■■■■■■■■■■■■■■ • Never attempt to plug the power cord into the power outlet or unplug the power cord when your hands are wet. • Never damage, modify, stretch, or excessively bend or twist the power cord. Do not place heavy objects on the power cord. • Never use any power supply other than the standard power supply available in the country of purchase. Using the incorrect voltage and frequency could cause a fire or electric shock.
6 Remove the protective cap from the print head. ➥Notes • Do not touch the print head nozzles or electrical contacts. • Do not attempt to reattach the protective cap once it has been removed. electrical contacts print head nozzles print head 7 Place the print head in the holder. print head holder 8 Lock the print head into place by lowering the lever. Do not touch the lock lever once the print head has been installed.
3 Hold the ink tank as shown in the diagram and remove the protective cap. ➥Notes • Do not squeeze the sides of the ink tanks as this may cause the ink to leak out and stain your clothes and hands. • Do not touch the ink port. • Do not attempt to reattach the protective cap once it has been removed. ink port 4 Insert the yellow ink tank into the righthand slot. Press the top until it clicks into place. 5 Use the same procedure to install the other ink tanks in their appropriate slots.
■■ 4 ■ Loading Paper ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ ■ Loading A4 (Letter) Size Plain Paper paper thickness lever 1 Open the front cover. 2 Move the paper thickness lever at the top of the print head holder to the left position. Close the front cover. ➥Note Set the paper thickness lever to the left when using plain paper, to the right when using thick paper. Refer to the User’s Guide for information on loading envelopes and other media.
■■ 5 ■ Installing the Printer Driver ■■■■■■■■■■■■■■■■■■■■■■ ➥Note If you are printing with only Direct Print, skip this chapter and go to “Aligning the Print Head” on page 16. ■ Installing the Printer Driver - Windows ➥Notes • Do not disconnect the cable or remove the CD-ROM during the installation. The driver cannot be correctly installed. • The screens below refer to Windows Me installation. Screen may differ depending on the environment you are using.
3 Place the Setup Software & User’s Guide CD-ROM in the CD-ROM drive. ➥Notes • If the CD-ROM does not run automatically, double-click My Computer in the Windows screen, for Windows XP, click Start and select My Computer, and then double-click the CD-ROM icon. • If the language selection screen appears, select a language, then click the Next button. 4 Follow the instructions displayed on the screen. When the screen shown on the left is displayed, click Install.
6 Click OK. Before you can use the printer, you must carry out print head alignment on page 16. 7 Click Install to install the memory card utility. 8 Click OK after having completed the installation. 9 When the screen shown on the left appears, click Exit. ➥Notes • To view the User's Guide, please refer to page 59. • If a message prompting you to restart the computer appears, click Yes.
1 Turn on the Mac. 2 Place the Setup Software & User’s Guide CD-ROM in the CD-ROM drive. 3 Double-click the Printer Driver folder, then select a language. 4 Double-click Installer. 5 Read the Licence Agreement and click Accept to continue. 6 Click Install. Wait for the installation to finish. ➥Note If the above message appears, check that there are no unsaved documents, then click the Continue button. If a document needs to be saved, click Cancel then save the document.
8 Double click Memory Card Utility of the CANON BJ folder. 9 Double click the BJ Installer. 10 Click . 11 Read the Software License Agreement and if you agree, click Agree and then click . 12 Click Install. Installation is started, and when completed, a message for successful installation will be displayed. Click Restart now.
13 Select Chooser in the Apple Menu. 14 Click the icon for the printer you are using and close Chooser. Before you use the printer, you must carry out print head alignment on page 18. ➥Note Refer to the User’s Guide when using this printer as a network printer.
■■ 6 ■ Aligning the Print Head ■■■■■■■■■■■■■■■■■■■■■■■■■ This operation must be carried out when using the printer for the first time. Aligning the print head positions allows you to print without shifts in the colour registration. ■ Aligning the Print Head - Windows 1 Click Start and select Printers in Settings. ➥Note For Windows XP, click Start and select Control Panel - Printers and Other Hardware - Printers and Faxes. 2 Click the icon for your printer.
7 After the pattern is printed, click Yes. If the pattern is not printed successfully, open the front cover and ensure that the ink tanks are correctly installed. 8 Look at the print-out. From the patterns in Column A, select the most even, least irregular pattern and enter the number. 9 In the same way, one by one, select the most even patterns printed with the least irregularities from each of Columns B to F, enter their numbers, and click OK.
■ Aligning the Print Head - Macintosh 1 Select Page Setup in the File menu. 2 Click Utilities. 3 Select Test Print from the menu and click the Print Head Alignment icon. 4 Check that paper is loaded in the printer and click OK. If the pattern is not printed successfully, open the front cover and ensure that the ink tanks are correctly installed. 5 Look at the print-out. From the patterns in Column A, select the most even, least irregular pattern and enter the number.
6 In the same way, one by one, select the most even patterns printed with the least irregularities from each of Columns B to F, enter their numbers and click Send. If it is difficult to pick the best pattern on Column F, pick the setting that produces the least noticeable vertical white stripes. Less noticeable white stripes More noticeable white stripes 7 Click Close. 8 Click OK. This completes the printer setup. The printer is now ready to use.
■ Adjusting the Print Head - Operation Panel To print photographs more beautifully, be sure to adjust the position of the print head before you begin printing on your purchased printer for the first time. You should also adjust the print head position if lines or smudges appear when you print photographs. 1 Press the Maintenance button. The Sheets. 2 Press the The icon is displayed in Required (right) button four times. icon is displayed. 3 Check that A4-sized paper is set, and press the Print button.
The icon is displayed. ➥Note To interrupt the operation and start over, press the Cancel button, and start over from step 1. 7 Repeat steps 5 and 6, and set the pattern numbers for columns B to F. When you finish pattern number settings for up to column F, the icon appears. 8 Press the Maintenance button. This completes the preparations for the printer.
Basic Operations • If you detect smoke, unusual smells or strange noises around the printer, immediately switch the printer off and always unplug the printer. Contact your local Canon service representative. • To avoid injury, never put your hand or fingers inside the printer while it is printing. ■■ 1 ■ Printing with Windows ■■■■■■■■■■■■■■■■■■■■■■■■■■ Adjusting the print settings according to your needs allows you to produce better quality prints.
■ Basic Print Settings For the best print quality, specify the minimum requirement settings in the Main tab. To get the best results, ensure you select the type of media loaded in the printer when printing on paper other than plain paper. (6) (1) (2) (3) (4) (5) (1) Media Type Select the type of media loaded in the printer. (2) Print Quality Select one option from High, Standard and Draft. Select Custom to set the print quality manually.
■■ 2 ■ Printing with Macintosh ■■■■■■■■■■■■■■■■■■■■■■■■ Adjusting the print settings according to your needs allows you to produce better quality prints. ■ Printing 1 Open the Page Setup dialog box in your application. On the File menu, click Page Setup. Check the application’s user’s manual for the actual procedures. 2 Specify the page setup. For details, refer to “Page Setup” on page 25. 3 Open the Print dialog box in your application to print the document. On the File menu, click Print.
■ Page Setup Use the Page Setup dialog box to specify the paper size settings. Select paper size you wish to use. ■ Basic Print Settings For the best print quality, specify the minimum requirement settings in the Print dialog box. To get the best results, ensure you select the type of media loaded in the printer when printing on paper other than plain paper. (3) (1) (2) (1) Media Type Select the type of media loaded in the printer.
Printing Without Using the Computer This chapter describes the procedure for using only the printer without the computer to print photographs taken with a digital camera. ■■ 1 ■ Before Printing ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ This section describes basic operations required for printing, including how to use the operation panel and memory card and how to connect a digital camera to the printer.
Operating the Cursor Buttons Moving between Items To move the (cursor), press the (down) buttons. (up) and Changing a Setting To change the photograph number or a setting, press the (left) and (right) buttons. The (right) button increases the photograph number; the (left) button decreases the photograph number.
■ Using a Memory Card This section explains how to set and remove a memory card. Memory Card and PC Adapter You can use the following memory cards. Set the memory card in the PC card adapter to use the card. • Compact flash (Use the PC card adapter that comes with this printer.) • Smart media • Memory stick • SD memory card • Multimedia card • Micro drive • Flash ATA card PCMCIA Type (II) (The PC card adapter is not necessary.
Setting the Memory Card ➥Note The operation procedure is different if you are using a memory card when the printer is connected to the computer. See the "User's Guide." 1 Turn on the printer. 2 Set the memory card into the PC card adapter. 3 Set the PC card adapter into the card slot. The indicator lamp will go on. The mark and ‘AT’* are displayed on the operation panel. * Setup for ‘AT’ *: Images are automatically corrected when data in formats supporting Exif2.2 (ExifPrint) is printed.
Ejecting the Memory Card ➥Note The operation procedure is different if you are using a memory card when the printer is connected to the computer. See the "User's Guide." 1 Check that the indicator lamp is not blinking. ➥Note If you remove the memory card or switch off the power to the printer while the indicator lamp is blinking, the data of the memory card may be destroyed. 2 Press the printer power button to turn off the computer. Indicator lamp Eject button.
■ 2 ■ Printing Photographs ■■■■■■■■■■■■■■■■■■■■■■■■■■■■ This section explains how to print photographs without using a computer. ■ Print Flow Print photographs according to the following procedure. The printing method can be selected from five modes: Index, All Frames, Single Frame, Specified Frame, and DPOF. 1 Setting the memory card Set the memory card (see page 29). 2 Selecting a print method Select a print method from the five selections.
❷ ❸ ❹ ❺ ❻ ❼ ❶ 3 Setting print details ❶ Setting the Number of Print Copies (see page 40) ❷ Setting the Media Type (see page 40) ❸ Setting the Print Layout (see page 41) ❹ Setting the Print Quality (see page 42) ❺ Printing the Date (see page 42) ❻ Correcting Photographs (see page 43) ❼ Operating the Cursor Buttons (see page 27) 4 Printing Load paper into the printer, and press the Print button.
■ Printing a Photograph List (Index Printing) This mode allows you to print a list of the photographs and photograph numbers stored on the memory card. Photograph Number ➥Notes • You will need the photograph numbers to specify the photographs to be printed. Note that these numbers are different from the ID numbers that the digital camera assigns. • Printing is enlarged or reduced automatically to match the paper size.
4 Press the Print button. Printing starts. ➥Note Specifying the range and print the photographs You can print only the specified range of the photographs in the memory card using either Index printing or All Frames printing function. Set the Print Index or Print All mode by using the Mode button, and then specify the range according to the procedure below. You will need the photograph numbers to specify the range of photographs to be printed. To check the photograph numbers, use index printing.
■ Printing a Sequential Range of Photographs (All Frames Printing) This mode allows you to print all photographs found on the memory card. You can also specify a range to print only some of the photographs. ➥Note Printing is enlarged or reduced automatically to match the paper size. Depending on the Media Type and Layout settings, the top, bottom, right, or left section of the photograph may be cut off when the photograph is printed. 1 Press the Mode button, and select Print All.
➥Notes • You will need the photograph numbers to specify the photograph to be printed. You can check the photograph numbers by printing an index. See "Printing a Photograph List (Index Printing)" on page 33. • Printing is enlarged or reduced automatically to match the paper size. Depending on the Media Type and Layout settings, the top, bottom, right, or left section of the photograph may be cut off when the photograph is printed. 1 Press the Mode button, and select Print One.
■ Printing Selected Photographs in Batch Printing (Specified Frame Printing) This mode allows you to specify photographs to be printed and print the photographs in batch printing. Up to 99 photographs can be specified. ➥Notes • You will need the photograph numbers to specify photographs to be printed. To check the photograph numbers, use index printing. For details, see "Printing a Photograph List (Index Printing)" on page 33. • Printing is enlarged or reduced automatically to match the paper size.
7 Display [-02-] by pressing the (right) button. [-02-] indicates the second frame. 8 To specify a frame after the second frame, repeat step 2 to 5. If you select ---- for Last, that frame will not be printed. 9 Set Media Type and Layout. See "Print Applications" on page 40. 10 Load paper into the printer. You will need the number of sheets displayed in Required Sheets. ➥Note For instructions on loading paper, see "Loading Paper" on page 9 or the "User's Guide.
1 Press the Mode button, and select DPOF mode. If none of the photographs have the DPOF specification, the DPOF mode cannot be selected. 2 Set Media Type and Layout. See "Print Applications" on page 40. ➥Note Specify the number of copies and date printing from the digital camera. On 3 Load paper into the printer. You will need the number of sheets displayed in Required Sheets. ➥Note For instructions on loading paper, see "Loading Paper" on page 9 or the User's Guide.
■■ 3 ■ Print Applications ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ You can set the type of paper and layout to be used in printing, the number of print copies, photograph correction, quality, and dated printing. Set these settings after you set the print mode (Index, All Frames, Single Frame, Specified Frame, and DPOF). ■ Setting the Number of Print Copies (Copies) Copies allows you to set the number of copies in Single Frame mode. ➥Notes • Copies cannot be set in Index, All Frames, or Specified Frame mode.
Operation panel display Media name and size [A] Photo Paper Pro for Borderless printing (PR-101) [B] Photo Paper Plus Glossy (4" × 6") (PP-101) [C] Photo Paper Pro (PC-101S) [D] Photo Paper Pro Letter size (PR-101) [E] Photo Paper Pro A4 size (PR-101) [F] Plain Paper Letter [G] Plain Paper A4 1 Set the print mode. See "Printing Photographs" on page 31. 2 Move the (cursor) to Media Type by pressing the (top) and (bottom) buttons.
2 Move the (cursor) to Layout by pressing the (top) and (bottom) buttons. 3 Select the layout by pressing the (left) and (right) buttons. Select to print a borderless photograph. Select to print a bordered photograph. ■ Setting the Print Quality (Quality) You can set the print quality. ➥Note The print quality that can be set differs according to the media type and the print mode. 1 Set the print mode. See "Printing Photographs" on page 31.
➥Note In DPOF mode, set Print Date from the digital camera. 1 Set the print mode. See "Printing Photographs" on page 31. 2 Move the (cursor) to Print Date by pressing the (top) and (bottom) buttons. 3 Select OFF (disable)/ON (enable) for date printing by pressing the or (right) button. (left) ■ Correcting Photographs (Image Correction) This function automatically corrects photographs before printing them.
➥Note To set more detailed photograph correction, two correction functions, a correction for colour fogginess and exposure (Photo Optimizer PRO function) and a correction for reproducing vivid colours (Vivid Photo function), are performed. To set only one correction function, follow the procedure below. 1 Select ON (enable) for Optimize Image by pressing the (right) button.
■ Using the Optional Image Viewer The optional TFT Image Viewer <> allows you to display JPEG image data stored on the inserted memory card and check the print layout of the first page. Switching the Viewer Display On/Off Switching the Viewer Display On After attaching the viewer to the printer, turn on the viewer display according to the following procedure: 1 Turn on the printer. 2 Insert the memory card containing saved JPEG data into the card slot (see page 29).
Specifying the printing area • The printing area can be chosen while Print All, Print One or Print Selected is selected. • This function is available only when (Borderless Printing) is selected for Layout. • Examples for cases when (Borderless Printing) are selected for the specified frame printing are introduced in this section. Specifying the printing area 1 Check that the printer power is on. 2 Insert a memory card to which JPEG data has been saved (see page 29).
Adjusting the Brightness and Contrast The brightness and contrast of the viewer display can be adjusted from maintenance mode. Adjusting the Brightness 1 Check that the printer power is on. 2 Insert a memory card to which JPEG data has been saved (see page 29). 3 Press the Maintenance button. The Sheets. 4 Press the The icon appears in Required (right) button five times. icon is displayed. 5 Press the Print button. The Image.
Adjusting the Contrast 1 Check that the printer is on. 2 Insert a memory card to which JPEG data has been saved (see page 29). 3 Press the Maintenance button. The Sheets. 4 Press the The icon appears in Required (right) button six times. icon appears. 5 Press the Print button. The Image. icon appears in Optimize 6 Adjust the contrast by using the (left) and (right) buttons. You can adjust the contrast within the following setting range by operating the buttons. The base setting is 0.
■ Using a Digital Camera You can print photographs connecting a Canon digital camera which has direct printing function. If you connect the digital camera to the printer, perform the print operations from the digital camera. You can use the following types of media when you connect a digital camera.
■■ 4 ■ If Photographs Cannot Be Printed Clearly (Operation Panel Section) If ink is still remaining but printing is blurred or a certain colour does not come out, nozzles in the print head may be clogged or the print head may be out of position. Use the Maintenance function to maintain the print quality. ■ Maintenance Operation Flow ➥Notes Before Performing the Maintenance Operation • Open the front cover, and check that the ink tanks are properly set by pressing the PUSH section of the ink tanks.
■ Printing the Nozzle Check Pattern Print the nozzle check pattern and check whether inks is being ejected properly from the print head nozzles and whether the print head is correctly positioned. ➥Note You can also print the nozzle check pattern by pressing the Reset button of the printer. Follow the procedure below. 1 Check that the printer is on. 2 Load A4-size plain paper. 3 Keep the Reset button pressed down, and release it when the power lamp blinks twice. 1 Check that the printer is on.
■ Cleaning the Print Head Clean the print head if a nozzle in the print head becomes clogged. Perform print head cleaning only when necessary because the operation consumes a lot of ink. ➥Note You can also perform print head cleaning by pressing the Reset button on the printer. Follow the procedure below. 1 Check that the printer is on. 2 Keep the Reset button pressed down, and release it when the power lamp blinks once. 1 Press the Maintenance button. The Sheets.
■ Deep cleaning the Print Head If print head cleaning is not effective, perform print head deep cleaning, which is a stronger cleaning process. Perform print head deep cleaning only when necessary because the operation consumes a lot of ink. 1 Press the Maintenance button. The Sheets. 2 Press the icon appears in Required (right) button three times. The icon appears. 3 Press the Print button. Print head deep cleaning starts. When deep cleaning is completed, the is displayed.
■■ 5 ■ If an Error Is Displayed on the Operation Panel ■■■■■ If an error number is displayed on the operation panel, correct the error according to the procedure below. ➥Note If the display or buttons on the operation panel are not operating properly even through an error is not displayed, turn off the printer, unplug the power cord, and then turn on the power again. error number Black Cyan Magenta ➥Note The colour of the ink tank affected by the error can be checked in Media Type.
Error number: 103 Cause: Position of paper thickness lever is incorrect and ink level is low. Corrective action: Prepare a replacement ink tank. Replace the ink tank (see page 57), and set the paper thickness lever to the correct position to start printing. Press the Print button to restart printing under the current conditions. Error number: 201 Cause: Ink has run out. Corrective action: Press the Cancel button to stop printing, and then replace the ink tank (see page 57).
Error: Photograph cannot be read from memory card (indicator lamp does not go on) Cause: • Memory card is not set properly. • Memory card was ejected while data was being read. • Memory card that cannot be used was set. • Memory card does not contain readable photographs. Corrective action: • Insert a memory card deeply that can be used (see page 29). If a memory card is already set, eject the card, set it again, and check that the indicator lamp goes on.
Print Head Maintenance ■ If Blurring Occurs or If a Specific Colour Does Not Print ➥Note The steps below can be performed only from the computer. If you perform them from the operation panel, refer to “If Photographs Cannot Be Printed Clearly” on page 50. Perform print head cleaning to improve the print quality. Ensure that the printer is turned on and follow the instructions below. • Windows Open the printer driver settings screen and click the Maintenance tab. Click the Cleaning icon.
Notes on Handling the USB Interface (for Windows Users) If installation of the printer driver does not proceed as instructed in this Quick Start Guide, there may be a problem with the USB driver installation. Try reinstalling the printer driver. ■ Reinstalling If you cannot proceed beyond the Printer Port screen: 1 Click Cancel. 2 When the Abort Installation screen is displayed, click Abort. 3 When the Terminate Installation screen is displayed, click OK. 4 Turn the printer off.
For Further Details... For more information, place the Setup Software & User’s Guide CD-ROM in the CD-ROM drive. ■ User’s Guide Contents The “User’s Guide” is in PDF format and can be found on the same CD-ROM as the printer driver. You can view this Guide on screen and print out any sections you require.
Additional Systems Requirements for User's Guide To install Adobe Acrobat Reader and view the User's Guide: • 8MB of available hard-disk space for Windows • 13MB of available hard-disk space for Mac OS • 640 x 480 pixels or greater, minimum 256 colours video display ■ Specifications Printing method: Bubble Jet on-demand Printing resolution: 2400 (horizontal) x 1200 (vertical) dpi. max.
Storage environment: Temperature: 0 to 35˚C (32 to 95˚F) Humidity: 5 to 90% RH (no condensation) Power supply: Europe AC 230 V±10%, 50 Hz USA/Canada AC 120 V, 60 Hz Australia AC 240 V, 50 Hz Power consumption: Standby: 6W Printing: 36 W Dimensions (without a paper rest and paper output tray): 430 (W) x 301 (D) x 188 (H) mm 16.9 (W) x 11.9 (D) x 7.4 (H) in Weight: Approx. 5.7 kg (12 lb.
Ordinary print media: Regular size: A4, A5, B5, 4”x6”, Letter, Legal, European DL, US Com.#10 Custom size: width: height: 90.0 to 215.9 mm (3.54 to 8.5 in) 120.0 to 584.2mm (4.72 to 23.
Storage function: Supported operating systems Windows XP, Windows 2000, Windows Me, Windows 98 Mac OS 8.6 or later Utilities Use the storage utility that comes with the printer. Functions Read, write Direct print function: Interface Card slot, Connector for digital camera print Operation panel Large LCD panel, 8 keys, 6 LEDs Supported paper types (The letters enclosed in brackets ([ ]) are the selection items in Media Type on the operation panel.
Print quality Up to three levels Date printing Supported Correction function Photo Optimizer PRO, VIVID Photo DPOF function Ver. 1.00-compliant (Print index prints, Set the number of copies, Select images for print, Include the date on the print, Include the file number on the print) Resolution Up to 1200×1200 dpi Specifications subject to change without prior notice.
QA7-2102-V01 XXXXXXXX ©CANON INC.
