PUB.
Introduction Important Usage Instructions WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. COPYRIGHT WARNING: Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be contrary to copyright laws. The Mains plug is used as the disconnect device. The Mains plug shall remain readily operable to disconnect the plug in case of an accident. CAUTION: • Danger of explosion if the wrong type of batteries are attached.
FCC/IC NOTICE HD Camcorder, VIXIA HF R42 / VIXIA HF R40 / VIXIA HF R400 systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for class B digital device, pursuant to Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS In these safety instructions the word “apparatus” refers to the Canon HD Camcorder VIXIA HF R42 / VIXIA HF R40 / VIXIA HF R400 and all its accessories. 1 2 3 4 5 6 7 8 9 10 11 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
REGIONS OF USE VIXIA HF R42 and VIXIA HF R40 are in compliance (as of January 2013) with the radio signal regulations of the regions listed below. For details on other regions where they can be used, make inquiries with the contacts listed on the back side of this instruction manual. REGIONS Canada, Hong Kong S.A.R.
Trademark Acknowledgements Y P O • SD, SDHC and SDXC Logos are trademarks of SD-3C, LLC. • Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. • App Store, iPad, iPhone, iTunes and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries. • HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Exciting Features and New Functions 6/4 Wi-Fi Functions Baby Mode (A 64) (A 122) Enjoy the freedom of Wi-Fi* by using convenient Wi-Fi functions such as the following. • You can use a smartphone as a remote control and record movies from a distance (A 125). • You can wirelessly connect the camcorder to your home network and upload your recordings to CANON iMAGE GATEWAY (A 130). This will allow you to even share your videos on YouTube and Facebook.
Smart AUTO (A 43) Smart AUTO automatically selects the best scene mode for the scene you want to shoot. You get spectacular recordings every time without worrying about settings. Video Snapshot Cinema-Look Filters (A 74) (A 65) Shoot or capture short scenes and arrange them into a video clip set to your favorite background music. Face Detection (A 76) C The camcorder automatically detects people’s faces and adjusts the focus and other settings accordingly for beautiful results.
Enjoying Your Recordings on Other Devices Connect the camcorder to an HDTV (A 105). Copy your recordings to an external video recorder (A 119). Upload recordings to your computer (A 111). Copy the camcorder’s entire memory onto an external hard drive (A 116). C Y P O Save your recordings. Upload your MP4 movies and photos to the Web (A 121).
6/4 Enjoying Your Recordings Using the Camcorder’s Wi-Fi Functions Use your iOS or Android smartphone or tablet to remotely control the camcorder (A 125). Use the Web browser on your iOS or Android smartphone or tablet to view the recordings on the camcorder (A 126). Y P O Save your recordings on an iPhone or iPad and play them back (A 128). C Connect the camcorder to an access point on your home network and then share your recordings on CANON iMAGE GATEWAY (A 130).
Table of contents Introduction 7 15 Exciting Features and New Functions About this Manual 17 Getting to Know the Camcorder 17 19 Supplied Accessories and CD-ROM Names of Parts Preparations 21 21 23 24 25 27 27 29 31 31 33 33 35 35 35 39 Getting Started Y P O Charging the Battery Pack Turning On the Camcorder Using the Grip Belt Opening the Lens Cover and Adjusting the LCD Screen C Using a Memory Card Memory Cards Compatible for Use with the Camcorder Inserting and Removing a Memory Card
Basic Shooting and Playback 41 41 43 45 46 47 50 50 54 56 58 Basic Recording Shooting Video About the Smart AUTO function Intelligent IS Taking Photos Zooming Basic Playback Playing Back Video Viewing Photos Deleting Scenes Deleting Photos Advanced Shooting 60 60 63 63 64 65 66 68 69 74 75 76 76 78 79 80 82 83 84 85 85 Selecting the Movie Format (AVCHD/MP4) Selecting the Video Quality 6/4 Selecting the Memory (Built-in Memory/ Memory Card) for Recordings 6/4 Dual Recording and Relay Recording Baby
86 87 89 90 Audio Scenes Audio Recording Level Using Headphones Using an External Microphone Advanced Playback and Editing 92 93 94 95 97 99 100 101 Capturing Video Snapshot Scenes and Photos from a Movie Playing Back Scenes in the Baby Album Playing Back Video Snapshot Scenes Playback with Background Music Selecting the Playback Starting Point Dividing Scenes Trimming Scenes Slideshow Y P O External Connections 102 Terminals on the Camcorder 103 Connection Diagrams C 105 Playback on a TV Scree
6/4 Wi-Fi Functions 122 125 126 128 130 136 137 141 Introduction to Wi-Fi Recording Movies Using a Smartphone as a Remote Control Remote Browse: Viewing Recordings Using a Web Browser on Your iOS Device or Android Smartphone Uploading Videos Using an iOS Device Sharing Recordings with CANON iMAGE GATEWAY Playback on a Computer Wi-Fi Connection Using an Access Point Viewing and Changing Wi-Fi Settings Additional Information 144 Appendix: Menu Options Lists 144 146 [ [ Main Functions] and [Edit] Panel
About this Manual Thank you for purchasing the Canon VIXIA HF R42 / VIXIA HF R40 / VIXIA HF R400. Please read this manual carefully before you use the camcorder and retain it for future reference. Should your camcorder fail to operate correctly, refer to Troubleshooting (A 158). Conventions Used in this Manual • • • • • • • IMPORTANT: Precautions related to the camcorder’s operation. NOTES: Additional topics that complement the basic operating procedures.
indicates that a function is available in the operating mode indicated and indicates that the function is not available. The operating modes are divided into the following three groups. For a detailed explanation, refer to Operating Modes (A 39). Brackets [ ] are used to refer to control buttons and menu options you will touch on the screen and to other onscreen messages and displays. Movie format Shooting mode Playback mode Self Timer Operating modes: * SCN * For movies only.
Getting to Know the Camcorder Supplied Accessories and CD-ROM The following accessories are supplied with the camcorder: XCA-110 Compact Power Adapter* BP-718 Battery PackW XIFC-300PCU/S USB Cable HTC-100/S High Speed HDMI CableW XQuick Guide XWi-Fi Basic Setup Guide** Y P O Transfer Utility LE Startup GuideW (see below) C * CA-110E including power cord, in Asia. ** 6/4 only.
The Canon VIXIA CD-ROM is also supplied with the camcorder. The CDROM contains the following components: - Instruction Manual - The full-version instruction manual of the camcorder (this PDF file). - ImageBrowser EX - The CD-ROM contains an automatic installer for the software ImageBrowser EX, which allows you to save and manage MP4 movies and photos and upload CANON iMAGE GATEWAY*, YouTube and Facebook. An Internet connection is required for full installation of the software.
Names of Parts Left side view 1 4 56 2 3 6 7 8 9 q A a A s A d A 7 8 Right side view 9 C A q A a 1 2 3 4 5 (playback mode) button (A 40) ON/OFF button (A 23) Memory card slot cover MIC (microphone) terminal (A 91) AV OUT terminal (A 102, 104)/ × (headphones) terminal (A 89) HDMI OUT terminal (A 102, 103) USB terminal (A 102, 104) Memory card slot (A 29) START/STOP button (A 41) DC IN terminal (A 21) Grip belt (A 24) Lens cover switch (A 25) Stereo microphone (A 87) Y P O A s Front view A d Int
Top view A f A g A f g A h A j A k A Speaker (A 52) Zoom lever (A 47) LCD touch screen (A 25, 35) ACCESS indicator (A 41) 64Wi-Fi antenna (A 124) A k LCD panel A h l POWER/CHG (charge) indicator: A Green - On Red - Charging (A 21) q Battery attachment unit (A 21) S a Serial number S Back view A j A k A l C Y P O S Tripod socket (A 176) s d BATTERY RELEASE switch (A 22) S S q Bottom view S a 20 Introduction S s S d
Preparations This chapter describes basic operations, such as using the touch panel, navigating the menus, and first time settings to help you learn more about your camcorder. Getting Started Charging the Battery Pack The camcorder can be powered with a battery pack or directly using the compact power adapter. For approximate charging times and recording/playback times with a fully charged battery pack, refer to Charging, Recording and Playback Times (A 182).
POWER/CHG (charge) indicator 4 Charging will start when the camcorder is turned off. • If the camcorder was on, the green POWER/CHG indicator will go out when you turn off the camcorder. After a moment, the POWER/CHG indicator will turn on in red (battery pack charging). The red POWER/ CHG indicator will go out when the battery pack is fully charged. • If the indicator flashes, refer to Troubleshooting (A 161). To remove the battery pack 1 Slide d in the direction of the arrow and hold it pressed down.
overseas travels or special power sources such as those on aircraft and ships, DC-AC inverters, etc. NOTES • We recommend charging the battery pack in temperatures between 10 °C and 30 °C (50 °F and 86 °F). If either the ambient temperature or the battery pack’s temperature is outside the range of approx. 0 °C to 40 °C (32 °F to 104 °F), charging will not start. • If the ambient temperature or the battery pack’s temperature is low, charging may take longer than usual.
Open the LCD panel to turn on the camcorder. To turn off the camcorder Close the LCD panel or press . [ NOTES • You can use the > q > [Power On Using LCD Panel] setting so that you can turn the camcorder on and off only by pressing . Using the Grip Belt C Y P O Fasten the grip belt. Adjust the grip belt so that you can reach the zoom lever with your index finger, and the Y button with your thumb. To remove the grip belt 1 Lift the padded handgrip’s flap and detach the strap from the Velcro pad.
2 Pull the strap to remove it first from the front bracket on the camcorder, then to unthread it from the handgrip and finally to remove it from the rear bracket on the camcorder. Opening the Lens Cover and Adjusting the LCD Screen Before you start recording, open the lens cover. Move the lens cover switch down to to open the lens cover. C Y P O Rotating the LCD Panel The first time you open the LCD panel, the initial setup screens will appear and guide you through the basic settings (A 31).
180° 180° Subject can monitor the LCD screen 90° NOTES • About the LCD screen: The screen is produced using extremely high-precision manufacturing techniques, with more than 99.99% of the pixels operating to specification. Less than 0.01% of the pixels may occasionally misfire or appear as black, red, blue or green dots. This has no effect on the recorded image and does not constitute a malfunction.
Using a Memory Card Memory Cards Compatible for Use with the Camcorder You can use the following types of commercially available Secure Digital (SD) cards with this camcorder. As of January 2013, the movie recording function has been tested using SD/SDHC/SDXC memory cards made by Panasonic, Toshiba and SanDisk. For the latest information on cards that can be used, visit your local Canon Web site. Memory card type: .
IMPORTANT • If you use an SDXC memory card with a computer OS that is not SDXCcompatible, you may be prompted to format the memory card. In such case, cancel the operation to prevent data loss. • After repeatedly recording, deleting and editing scenes (fragmented memory), it will take longer to write data on the memory and recording may stop. Save your recordings and initialize the memory.
Inserting and Removing a Memory Card If you plan on using a memory card, turn off the camcorder before performing the initial setup and then insert the memory card. After performing the initial setup, initialize the memory card (A 33). 1 Open the LCD panel. If this is your first time to turn on the camcorder, the language selection screen of the initial setup screens will appear. 2 Press to turn off the camcorder. Make sure the POWER/CHG indicator is off. 3 Open the memory card slot cover.
IMPORTANT • Memory cards have front and back sides that are not interchangeable. Inserting a memory card facing the wrong direction can cause a malfunction of the camcorder. Be sure to insert the memory card as described in step 4.
First Time Settings Basic Setup The first time you turn on the camcorder, you will be guided by the camcorder’s easy-to-follow setup screens to configure the camcorder’s initial settings. You will set the date and time, movie format, and other basic functions. For details on how to use the touch screen, refer to Using the Touch Screen (A 35). 1 Touch the language used for onscreen displays and then touch [æ]. • You may need to scroll down to find your language.
• 7 Skip to step 10. 8 Touch [&] (built-in memory) or [ ] (memory card) and then touch [æ]. • When selecting the memory, you can check the available recording time based on the video quality setting. • After you select the memory to which you want to record movies, the [{ Rec Media for Photos] screen will appear. 9 Touch [&] (built-in memory) or [ ] (memory card) and then touch [æ]. When selecting the memory, you can check the number of photos that can be recorded, based on a photo size of 1920x1080.
Changing the Time Zone Change the time zone to match your location. The default setting is New York. In addition, the camcorder is able to retain the date and time of another location. This is convenient when you travel so that you can set the camcorder to match the time of your home location or that of your destination. Operating modes: SCN 1 Open the [Time Zone/DST] screen.
6/4 > [ Other Settings] > q > [Initialize &/ ] > [& Built-in Mem.] or [ Mem. Card] > [Initialize] > [Complete Initialization]1 > [Yes]2 > [OK] > [X] 7 > [ Other Settings] > q > [Initialize ]> [Initialize] > [Complete Initialization]1 > [Yes]2 > [OK] > [X] 1 2 Touch this option if you want to physically erase all the data rather than just clear the file allocation table of the memory.
Basic Operation of the Camcorder Using the Touch Screen The control buttons and menu items that appear on the touch screen change dynamically depending on the operating mode and the task you are performing. With the intuitive touch screen interface you have all the controls at your fingertips. Touch Touch on an element displayed on the touch screen. Used to start playing back a scene in an index screen, to select a setting from the menus, etc.
(Home) Menu The (Home) menu is the gateway to most of the camcorder’s functions and settings. Operating modes: SCN 1 Touch [ menu. ] on the upper left of the screen to open the (Home) 2 Drag your finger left/right to bring the desired menu to the center. 3 Touch the icon of the desired menu to open it. See below for a description of each menu. The menus that appear depend on whether the camcorder is in recording mode or playback mode.
Menu Description [ Main Functions] This contains functions commonly used while shooting, such as focus and exposure. For details on how to navigate this menu, refer to [ Main Functions] Panel (A 38). [ Remote Control+ Streaming]* After installing the remote control app, use your smartphone as a remote control to record movies with the camcorder (A 125). * 6/4 only. Menus Available in Playback Mode Menu Description Other Settings] menus (A 37).
Operating modes: SCN * * In mode, access to functions is limited. 1 Touch [ ] on the upper left of the screen to open the (Home) menu. 2 Drag your finger left/right to bring [ Other Settings] to the center. 3 Touch the icon to open the [ Other Settings] menus. 4 Touch the tab of the desired menu. 5 Drag your finger up/down to bring the setting you want to change into the orange selection bar. • You can also use the [Í] and [Î] icons for scrolling. • Menu items not available appear grayed out.
In mode Drag your finger up and down along the scroll bar to display the rest of the panel Touch to scroll up or down Touch the control button of the desired function You may need to drag your finger up and down along the scroll bar or touch [Í] and [Î] to find the control button of the desired function.
Shooting mode (AUTO mode) (Cinema mode) SCN (Special scene modes) (Programmed AE mode) Operation Let the camcorder take care of most of the settings while you concentrate on recording (A 41). Great for beginners or if you just prefer not to bother with detailed camcorder settings. Give your recordings a cinematic look and use cinema-look filters to create unique movies (A 65). From nightscapes to beaches, have the camcorder select the best settings that match the situation you are in (A 66).
Basic Shooting and Playback This chapter covers how to easily record video and photos in mode, play them back, and how to use other basic functions. To enjoy full access to menus and more advanced functions, refer to Advanced Shooting (A 60) and Advanced Playback and Editing (A 92). Basic Recording Shooting Video With mode, you can take great-looking videos by letting the camcorder automatically adjust settings based on the recording situation.
3 Set the camcorder to mode. (shooting mode button) > [N Auto] > [OK] • This step is not necessary the first time you use the camcorder. • To change the movie format, refer to Selecting the Movie Format (AVCHD/MP4) (A 60). Shooting mode button 4 Press Y to begin recording. • Press Y again to pause the recording. • The ACCESS indicator will flash from time to time while the scene is being recorded. Y P O When you have finished recording 1 Make sure that the ACCESS indicator is off.
About AUTO mode • Only the following functions are available in mode. - Zoom (A 47). - Video snapshot (A 74). - Face detection and tracking (A 76) to get beautiful shots of people every time, tracking the subject even if the person moves. - Decoration (A 69) to add a fun personal touch using stamps, drawings, image mix and more. About the Smart AUTO function In mode, the camcorder will automatically detect certain characteristics of the subject, background, lighting conditions, etc.
Smart AUTO icons Background → (color of the icon) Bright* (gray) Subject ↓ Blue skies* (light blue) Vivid colors* (green/red) Sunsets (orange) People (stationary) ( ) ( ) ( ) — People (moving) ( ) ( ) ( ) — Subjects other than people, such as landscapes ( Close objects ) ( / ( / ) Background → (color of the icon) People (stationary) People (moving) Close objects ( ) ( / / ) ( / Dark (dark blue) Subject ↓ Subjects other than people, such as landscapes ) / C / Spot
Intelligent IS Intelligent IS allows the camcorder to select the best image stabilization option based on your shooting method. During and mode, the Intelligent IS icon will change to one of the following icons. In other shooting modes, you can set the image stabilization manually (A 75).
> [LCD Backlight] setting or adjust the brightness of the LCD screen with the > > [LCD Brightness] setting. • If you plan on making a long recording while the camcorder is in a fixed position, such as on a tripod, you can record with the LCD panel closed in order to conserve the battery’s power. In such case, make sure > q > [Power On Using LCD Panel] is set to [Off]. • Under certain conditions, the Smart AUTO icon that appears on the screen may not match the actual scene.
A green icon ( ) and {æ& (6/4 only) or {æ will appear momentarily on the screen and the ACCESS indicator will flash as the photo is recorded. However, if you record a photo while recording a will not appear. movie, When you have finished taking photos 1 Make sure that the ACCESS indicator is off. 2 Close the LCD panel to turn off the camcorder. You can also press . 3 Slide the lens cover switch up.
Using the Zoom Lever Move the zoom lever toward T (wide angle) to zoom out. Move it toward S (telephoto) to zoom in. By default, the zoom lever operates at a variable speed – press gently for a slow zoom; press harder for faster zooms. W W T T Zoom out T S Zoom in Using the Touch Screen’s Zoom Controls 1 Display the zoom controls on the touch screen. > [ZOOM] C Y P O • The zoom controls appear on the left side of the screen. 2 Touch the zoom controls to operate the zoom.
Operating modes: * * * In SCN mode, [Zoom Type] will be set to [ Optical]. > [Zoom Type] > Desired zoom type > [X] Options [ Optical] For optical zoom, the camcorder uses the optical magnification ratio of the lens. [ Advanced] For advanced zoom, the camcorder processes the image beyond the range of the optical zoom to obtain a larger zoom without any deterioration in image quality. At full wide angle, the angle of view with advanced zoom is wider than the angle of view with optical zoom.
Basic Playback Playing Back Video Operating modes: SCN 1 Press . Index screen button (next to [ ]) Y P O 2 If necessary, change the index screen.
! Index screen button. Displays the currently selected memory (6/4 only) and movie format. Press to change the index screen. " Drag your finger left/right for the next/previous index page. # Display the next/previous index page. $ Scene’s timeline (A 97; for AVCHD movies). I Scene information (for MP4 movies). % Recording date (for AVCHD movies) or folder name (for MP4 movies; A 152). C Y P O 3 Look for the scene you want to play back. 4 Touch the desired scene to play it back.
3 Touch [K] twice when finished. During playback: ! Jump to the beginning of the scene. Double-tap to jump to the previous scene. " Jump to the beginning of the next scene. # Pause the playback. $ Fast playback* backward/forward. % Display the volume (A 52) and background music mix balance (A 95) controls. & Stop the playback. ' Decoration (A 69).
During playback pause: ! Resume playback. " Slow playback* backward/forward. # Capture the displayed frame as a photo (A 93). $ Decoration (A 69). * Touch several times to increase the playback speed 1/8 → 1/4 the normal speed. IMPORTANT Y P O • Observe the following precautions while the ACCESS indicator is on or flashing. Failing to do so may result in permanent data loss. - Do not open the memory card slot cover. - Do not disconnect the power source or turn off the camcorder. - Do not press .
• Sound will not be output from the built-in speaker while the supplied High Speed HDMI cable or optional STV-250N Stereo Video Cable is connected to the camcorder. Viewing Photos Operating modes: SCN 1 Press . 2 Open the [ >[ Y P O Photo Playback] index screen. C Photo Playback] 3 6/4 If necessary, change the index screen.
! 6/4 Index screen button. Displays the currently selected memory. Press to change the index screen. " Drag your finger left/right for the next/previous index page*. # Display the next/previous index page. $ Folder name (A 152) * While browsing through index pages, a larger scroll bar will appear at the bottom of the screen for a few seconds. When you have a large number of photos it may be more convenient to drag your finger along the scroll bar. Y P O 4 Look for the photo you want to play back.
[h] > Drag your finger left and right along the scroll bar > [K] IMPORTANT • Observe the following precautions while the ACCESS indicator is on or flashing. Failing to do so may result in permanent data loss. - Do not open the memory card slot cover. - Do not disconnect the power source or turn off the camcorder. - Do not press . • The following image files may not be displayed correctly. - Images not recorded with this camcorder. - Images edited on a computer. - Images whose file names have been changed.
Deleting Scenes from the Index Screen Operating modes: SCN 1 Open the desired index screen (A 50, 93, 94). To delete all the scenes recorded on a specific date, drag your finger left/right until a scene you want to delete appears. 2 Delete the scenes. [Edit] > [Delete] > Desired option* > [Yes]** > [OK] * When you select [Select], perform the following procedure to select the individual scenes you want to delete before touching [Yes]. ** Touch [Stop] to interrupt the operation while it is in progress.
• Observe the following precautions while the ACCESS indicator is on or flashing (while scenes are being deleted). - Do not open the memory card slot cover. - Do not disconnect the power source or turn off the camcorder. - Do not change the camcorder’s operating mode. NOTES • To delete all movies and make all recordable space available again you may prefer to initialize the memory (A 33). Deleting Photos You can delete those photos that you are not interested in keeping.
* When you select [Select], perform the following procedure to select the individual photos you want to delete before touching [Yes]. ** Touch [Stop] to interrupt the operation while it is in progress. Some photos will be deleted nevertheless. To select individual photos 1 Touch the individual photos you want to delete. • A checkmark ! will appear on the photos you touch. The total number of selected photos will appear next to the " icon. • Touch a selected photo to remove the checkmark.
Advanced Shooting This chapter covers advanced shooting functions, such as Special Scene modes and Baby mode. For details about basic video shooting, refer to Basic Shooting and Playback (A 41). Selecting the Movie Format (AVCHD/MP4) You can choose to record movies in AVCHD or MP4 format. AVCHD movies are ideal for playback with fantastic picture quality. MP4 movies are versatile and can easily be played back on smartphones or uploaded to the Web.
>[ Recording Setup] > [Video Quality] > Desired video quality* > [K] > [X] * You can view information on the video quality with the following procedure. To view information on the video quality 1 Touch [I]. A screen with the resolution, bit rate and frame rate will appear. 2 Touch [K]. NOTES • Movies recorded in 60P or MXP mode cannot be saved on AVCHD discs. Use an external Blu-ray Disc recorder compliant with AVCHD Ver. 2.0 specifications to copy those movies onto Blu-ray discs.
Approximate recording times Default value For AVCHD movies: Video quality → 60P1 MXP1 FXP1 LP2 8 GB Memory card/ 4 Built-in memory3 35 min. 40 min. 1 hr. 3 hr. 16 GB Memory card 1 hr. 15 min. 1 hr. 25 min. 2 hr. 5 min. 6 hr. 5 min. 32 GB Memory card/ 6 Built-in memory3 2 hr. 30 min. 2 hr. 55 min. 4 hr. 10 min. 12 hr. 15 min.4 64 GB Memory card 5 hr. 5 min. 5 hr. 55 min. 8 hr. 20 min. 24 hr. 30 min.
6/4 Selecting the Memory (Built-in Memory/Memory Card) for Recordings You can select to record your movies and photos in the built-in memory or on a memory card. The default memory for recording both is the built-in memory.
- When the video quality is set to 60P or 35 Mbps. - When the shooting mode is set to or . • When dual recording is activated, decoration is not available. • When you use relay recording, there will be a momentary stop in the scene at the point where the camcorder switches from one memory to another. Baby Mode Baby’s first smile, first step, first word. When you use mode, you can easily capture those once-in-a-lifetime moments and keep track of baby’s growth day by day.
Cinema Mode and Cinema-Look Filters In mode, the camcorder will adjust the frame rate and several other picture-related settings to give your recordings a cinematic look. In this mode you can also use a variety of professional cinema-look filters to create unique movies with a distinctive appearance. When you convert movies to MP4, you can add cinema-look filters (A 110). Operating modes: SCN Set the shooting mode to .
To change the cinema-look filter 1 Touch [FILTER 1]. 2 Select the desired cinemalook filter. Options ( Default value) The camcorder offers 7 cinemalook filters. Select the desired filter while previewing the effect on the screen. [1. Cinema Standard] [2. Vivid] [3. Cool] [4. Nostalgic] [5. Sepia] [6. Old Movies] [7. Dramatic B&W] C NOTES • When the shooting mode is set to available.
(shooting mode button) > [ƒ Scene] > [OK] > Desired Special Scene mode > [OK] Shooting mode button Options ( Default value) [ Portrait] [ Sports] To record sports scenes such as tennis or golf. [ Night Scene] The camcorder uses a large aperture, to achieve a sharp focus on the subject while blurring the background. lower noise. Y P O To record nightscapes with C [ Snow] To record in bright ski resorts without the subject being underexposed.
[ Low Light] [ Spotlight] [ Fireworks] To record in low-light situations. To record spotlit scenes. To record fireworks. NOTES • [ Portrait]/[ Sports]/[ Snow]/[ Beach]: The picture may not appear smooth during playback. • [ Portrait]: The blur effect of the background increases the more you zoom in (S). •[ Snow]/[ Beach]: The subject may become overexposed on cloudy days or in shaded places. Check the image on the screen. • [ Low Light]: - Moving subjects may leave a trailing afterimage.
Operating modes: SCN (shooting mode button) > [’ Programmed AE] > [OK] Shooting mode button Decoration: Adding a Personal Touch Add a new level of enjoyment to your scenes by decorating them. You can add animated graphics, stamps and even your own freehand drawing easily just by simply using your fingertip. When you convert movies to MP4, you can add decorations (A 110). C Y P O Decorating Scenes while Recording Operating modes: SCN 1 Open the decoration screen.
! Canvas - The area where you will draw and see your decorations in action. " Toolbar. # [Ó Pens and Stamps] Select the type of pen or stamp and its color. You can also save a single canvas or load a previously saved canvas. $ [× Animated Stamps] Select animated stamps to add to your decoration. % [& Date/Time] / [ ] Add the date and/or time as a caption that will be included in the recording. In mode, add stamps to track baby’s age, height and weight.
• To select a different pen or stamp: Repeat steps 1 and 2. • To change color: Touch [Ó] and then touch the white or black button under [Colors]. Alternatively, touch [Ó] > [Ö] and select a color from the color palette. • To clear your freehand drawings and stamps: Touch [Ó] > [Clear] > [Yes] > [K]. • To save your freehand drawings and stamps: Touch [Ó] > [&Save]1 or [ Save]1 > [Yes] > [K].
Operating modes: SCN 1 Touch [ ]. • The screen with stamps for mode will appear. 2 Select and set the desired stamps. • To add the age stamp: Touch [0 days] > [w] > Í/Î to set baby’s date of birth > [K]. • To add the height stamp: Touch [20 in.] > [w] > Í/Î to set baby’s height > [K]. • To add the weight stamp: Touch [6 lb. 8 oz.] > [w] > Í/Î to set baby’s weight > [K]. • To add the current date or time: Touch [Date] or [Time]. • To remove a selected stamp, touch it again. 3 Touch [K].
POINTS TO CHECK • 6/4 Before performing this procedure, make sure the memory with the image mix data is selected (A 63). At the time of purchase, image mix data is in the built-in memory. 1 Touch [Ü] to open the [Select Image] screen and then touch [ON]. 2 Touch [+] or [-] to select a different image mix frame. 6/4 You can touch one of the memory icons at the bottom of the screen to read image mix frames saved on a different memory (only when recording on or playing back scenes from a memory card).
5 Touch [K] to mix your image with live video. Decorating Scenes during Playback Operating modes: SCN 1 From the index screen (A 50), play back the scene you want to decorate. 2 Touch the screen to display the playback controls. 3 Touch [Ò] to open the decoration screen. 4 Decorate the scene using the tools from the toolbar as explained in the previous section. NOTES • Initializing a memory will erase any [Pens and Stamps] drawing canvas and image files you may have saved.
1 Activate video snapshot. > [¦ Video Snapshot] > [ON] > [X] • Touch [OFF] instead to deactivate video snapshot. • A blue border appears on the screen. 2 Press Y. The camcorder records for a few seconds (the blue frame serves as a visual progress bar) and then automatically returns to record pause mode.
( Default value) Options [ Dynamic] Compensates for a higher degree of camcorder shake, such as when shooting while walking, and is more effective as the zoom approaches full wide angle. [ Standard] Compensates for a lower degree of camcorder shake, such as when shooting while remaining stationary, and is suitable for shooting natural-looking scenes. [j Off] Use this setting when the camcorder is mounted on a tripod.
Operating modes: * * SCN * Face detection and tracking are always activated in and modes. POINTS TO CHECK • Select a shooting mode other than the [ Night Scene], [ or [ Fireworks] Special Scene mode in SCN mode. Low Light] By default, face detection and tracking are activated so you can skip step 1 in the following procedure. If the function was turned off, perform the following procedure starting from step 1. 1 Activate face detection and tracking.
• In certain cases, faces may not be detected correctly. Typical examples include: - Faces extremely small, large, dark or bright in relation to the overall picture. - Faces turned to the side, at a diagonal or partially hidden. • Face detection cannot be used when the shutter speed used is slower than 1/30 (1/24 if the frame rate is set to [»]), when the digital zoom is activated at more than 212x zoom or when using a smartphone or tablet to remotely control the camcorder.
To fade in/out Press Y in record pause mode to start recording with a fade in. Press Y while recording to fade out and pause the recording. NOTES • When you apply a fader, not only the picture but also the sound will fade in or out. • Faders cannot be used in the following cases: - While using the [Old Movies] cinema-look filter in mode. - When recording scenes with decorations. - When recording video snapshot scenes. - While pre-recording is activated. - When the video quality is set to 60P or 35 Mbps.
• The Touch AE mark (I) will flash and the exposure will be adjusted automatically so the area you touched will be correctly exposed. You have the option to further adjust the exposure manually as necessary. • You can touch [n] instead to adjust the exposure manually without activating the Touch AE function. • The manual adjustment dial appears and the adjustment value is set at ±0. • Touch [n] again to return the camcorder to automatic exposure.
• Reflective surfaces • Subjects with low contrast or without vertical lines Operating modes: • Fast moving subjects • Through wet windows • Night scenes SCN POINTS TO CHECK • Adjust the zoom before you start the procedure. 1 Open the manual focus screen. > [< Focus] 2 Touch a subject that appears inside the < frame. • The Touch AF mark (I) will flash and the focusing distance will be adjusted automatically. You have the option to further adjust the focus manually as necessary.
NOTES • When you use [E] and [F] to adjust the focus manually, you can touch inside the frame to automatically focus on that spot. Pre-Recording The camcorder will start recording 3 seconds before you press Y, ensuring you do not miss important shooting opportunities. This is especially useful when it is difficult to predict when to start recording. Operating modes: * SCN * Pre-recording is always activated in mode. 1 Activate the pre-recording function.
- Changing the shooting mode. White Balance The white balance function helps you to accurately reproduce colors under different lighting conditions so that white objects will always look truly white in your recordings. Operating modes: SCN > [Ä White Balance] > Desired option* > [X] * When you select [Å Custom WB], set the custom white balance with the following procedure before touching [X].
- Depending on the light source, Å may keep flashing. The result will still be better than with [Ã Automatic]. • Custom white balance may provide better results in the following cases: - Changing lighting conditions - Close-ups - Subjects in a single color (sky, sea or forest) - Under mercury lamps, certain types of fluorescent lights and LED lights Self Timer Operating modes: * SCN * For movies only. > [ Other Settings] > p > [Self Timer] > [i On <] > [X] Y P O • < will appear on the screen.
Frame Rate You can change the frame rate (the number of frames recorded per second) to change the look of your movies. Operating modes: SCN >[ Recording Setup] > [Video Quality] > [I] > Desired frame rate > [K] > [K] > [X] Options for AVCHD movies ( Default value) [´] 60 fields per second, interlaced. Standard frame rate of NTSC TV signals. [·] Shooting at 30 frames per second, progressive*. Use this frame rate to easily edit your recordings, for example, to post them on the Web.
POINTS TO CHECK • Select a shooting mode other than the [ mode in SCN mode. Fireworks] Special Scene 1 Activate tele macro. > [ZOOM] > [W]* (tele macro) * Touch again to turn off the tele macro function. • The camcorder will automatically adjust the zoom to the telephoto end. 2 Touch [START]. • Touch [STOP] to pause the recording. 3 Touch [X]. NOTES Y P O • Any of the following actions will deactivate the tele macro function. - Turning off the camcorder. - Pressing .
>[ Options [ [ Audio Scene] > Desired audio scene > [X] ( Default value) Standard] To record most general situations. The camcorder records with standard settings. Music] To vibrantly record music performances and singing indoors. [ [ Speech] Best for recording human voices and dialog. Forest and Birds] To record birds and scenes in forests. The [ Noise Suppression] camcorder clearly captures sound as it spreads.
Manual audio level adjustment Audio level indicator Current audio level Audio level adjustment bar 2 Touch and hold [Ï] or [Ð] to adjust the audio recording level as necessary. As a guideline, adjust the audio recording level so that the audio level meter will go to the right of the -12 dB mark (yellow area) only occasionally. 3 Touch [X] to lock the audio recording level at the current level.
Using Headphones Use headphones for playback or to check the audio level while recording. The headphones are connected to the AV OUT/× terminal, which is used for both the headphones and the audio/video output. Before connecting the headphones, follow the procedure below to change the function of the terminal from AV output to × (headphones) output. Do not connect the headphones to the AV OUT/× terminal if the Ó icon does not appear on the screen.
To adjust the volume during playback In mode, and in mode during slideshow playback, adjust the headphones volume the same way you adjust the speaker’s volume (A 52, 101). IMPORTANT Y P O • When using headphones, make sure to lower the volume to an appropriate level. C NOTES • Use commercially available headphones with a ∅ 3.5 mm minijack.
Using the WM-V1 Wireless Microphone Using the optional WM-V1 Wireless Microphone, you can reliably record sound even when recording subjects at a distance exceeding the practical range of the built-in microphone. For details on connecting and using the WM-V1, refer to the instruction manual supplied with the microphone. Using Commercially Available Microphones You can also use commercially available condenser microphones with their own power supply. You can connect almost any stereo microphone with a ∅ 3.
Advanced Playback and Editing In this chapter, you can learn how to use functions related to playback and editing, such as capturing video snapshot scenes and photos from your movies and playing back your movies with background music. Capturing Video Snapshot Scenes and Photos from a Movie You can capture video snapshot scenes or photos from a previously recorded scene.
• Video snapshot scenes cannot be captured from scenes shorter than 1 second. • When the source scene is itself a video snapshot scene, you may not be able to capture a video snapshot scene depending on the length of the source scene and the length currently selected for video snapshot scenes. • When you start capturing a video snapshot scene less than 1 second from the end of the scene, the video snapshot scene will be captured starting from the beginning of the following scene.
Operating modes: SCN 1 Open the baby album. >[ Baby Album] 2 Select the scene you want to play back. Drag your finger left/right to bring the desired scene to the front. 3 Touch the scene’s thumbnail to start the playback. • The camcorder will play back the scene selected and continue until the end of the last scene in the index screen. • Playback controls are the same as when playing back scenes from the [y Movie Playback] index screen (A 50).
2 Select the scene you want to play back. Drag your finger left/right to bring the desired scene to the front. 3 Touch the scene’s thumbnail to start the playback. • The camcorder will play back the scene selected and continue until the end of the last scene in the index screen. • Playback controls are the same as when playing back scenes from the [y Movie Playback] index screen (A 50). IMPORTANT • Observe the following precautions while the ACCESS indicator is on or flashing.
2 Select the music track. > [ Other Settings] > s > [Select Music] > [i On] > [Í] or [Î] to select the desired music track ! Select the desired music track. " Adjust the background music balance. # Play back the original sound (no background music). $ Delete the music track selected. % Listen to the music track selected. Touch again (Ñ) to stop the playback. Y P O 3 Adjust the mix balance between the original sound and the background music.
[ ] > [Yes] IMPORTANT • If you use copyrighted songs and music tracks in your video creations, remember that music under copyright may not be used without permission from the copyright holder, except for cases permitted under applicable laws, such as for personal use. Make sure to follow applicable laws when using music files. NOTES • Initializing a memory card will permanently erase any music files you may have transferred to the card.
2 Open the scene’s [Timeline] screen. [ ] > Desired scene • The [Timeline] screen appears. The large thumbnail will show the first frame of the scene. Below it, the timeline ruler shows frames taken from the scene at fixed intervals. 3 Touch the desired frame in the timeline ruler to start playing back the scene from that point. Y P O ! Touch twice to return to the index screen. " Previous/next scene. # Drag your finger left along the ruler to display the next 5 frames.
Dividing Scenes You can divide AVCHD scenes in order to leave out the best parts and later cut out the rest. Operating modes: SCN 1 Play back the desired scene (A 50). 2 Touch the screen and then touch [Ý] to pause the playback. 3 Open the screen for dividing scenes. [Edit] > [Divide] 4 Bring the scene to a precise point, if necessary. Playback controls will appear on the screen (A 52). Use any special playback modes (fast playback, frame reverse/advance) as necessary to locate the desired point.
Trimming Scenes You can trim MP4 scenes by removing everything up to a certain point or everything after a certain point. By doing so, you leave only memorable moments to keep for posterity. Operating modes: SCN 1 Play back the desired scene (A 50). 2 Touch the screen and then touch [Ý] to pause the playback. 3 Open the screen for trimming scenes. [Edit] > [Trim] 4 Bring the scene to a precise point, if necessary. • The point at which is movie will be trimmed is indicated by the marker.
Slideshow You can play a slideshow of all the photos and even set it to music. Operating modes: SCN 1 Open the [ Photo Playback] index screen (A 54). 2 Select the music track. > [ Other Settings] > > [Select Music] > [i On] > [Í] or [Î] to select the desired music track > [K] 3 Touch the photo that will open the slideshow to display it in single photo view. Y P O 4 Touch the screen to display the playback controls, then touch [Ð] to play back the slideshow set to the selected music track.
External Connections This chapter explains how to connect your camcorder to an external device such as a TV, VCR, or computer. 6/4 You can also use the camcorder’s convenient Wi-Fi functions (A 122). Terminals on the Camcorder Open the LCD panel to access the terminals on the camcorder. C Y P O (cable connector shown upside-down) 1 AV OUT/× Terminal 2 HDMI OUT Terminal* The HDMI OUT terminal offers a high-quality digital connection that combines audio and video in a single convenient cable.
Connection Diagrams In the following connection diagrams, the left side shows the terminals on the camcorder and the right side shows (for reference only) an example of terminals on a connected device. Connection ! HDMI Type: Digital Quality: High definition Output only Connect to a high-definition TV (HDTV) with an HDMI input terminal.
Connection " Composite Video Type: Analog Quality: Standard definition Output only Connect to a standard TV or a VCR with audio/video input terminals.
NOTES • Power the camcorder using the compact power adapter and only then connect it to the computer using the supplied USB cable in the following cases. - To write back scenes recorded with this camcorder that were previously saved on a computer. For details, refer to the Software Guide (PDF file) of PIXELA’s software. - To transfer music files from the supplied VIXIA CD-ROM to a memory card in the camcorder in order to use them as background music.
NOTES • You can also play video directly from your memory card on AVCHDcompatible HDTVs and digital recorders with a card slot compatible with the type of memory card used*. • We recommend powering the camcorder using the compact power adapter. • Connection ": When you play back your 16:9 movies on standard TV sets with a 4:3 aspect ratio, the TV set will switch automatically to widescreen mode if it is compatible with the Video ID-1 system. Otherwise, change the aspect ratio of the TV manually.
Saving and Sharing Your Recordings 6/4 Copying Movies and Photos to a Memory Card You can copy your recordings from the built-in memory to a memory card. Copying Scenes from the Index Screen Operating modes: SCN 1 Open the desired index screen in the built-in memory (A 50, 93, 94). To copy all the scenes recorded on a specific date, drag your finger left/right until a scene you want to copy appears. 2 Copy the scenes.
Options [date/folder name] Copy all the scenes recorded on a particular date. For AVCHD movies, the date will appear in the control button. For MP4 movies, the folder name* (A 152) will appear. [Select] Select individual scenes to copy. [All Scenes] Copy all the scenes. * The last four digits of the folder name indicate the date the folder was created. Copying a Single Photo Operating modes: SCN 1 In single photo view, select the photo you want to copy.
* When you select [Select], perform the following procedure to select the individual photos you want to copy before touching [Yes]. ** Touch [Stop] to interrupt the operation while it is in progress. To select individual photos 1 Touch the individual photos you want to copy. • A checkmark ! will appear on the photos you touch. The total number of selected photos will appear next to the " icon. • Touch a selected photo to remove the checkmark. To remove all checkmarks at once, touch [Remove All] > [Yes].
6/4 Converting Movies to MP4 Format You can convert AVCHD movies into MP4 movies or even convert MP4 movies into smaller MP4 movies. This is convenient, for example, when you want to upload the MP4 movies to the Web. The movie you want to convert must be in the built-in memory. After conversion, the resulting MP4 movie will be saved on the memory card. Operating modes: SCN 1 Open the desired index screen in the built-in memory (A 50, 93, 94). 2 Open the screen for selecting scenes to convert.
NOTES • When you convert movies, the video quality you can choose for the resulting MP4 movie will depend on the video quality of the original movie. Based on the following options, movies in the built-in memory will be converted and then copied to the memory card. Video quality before conversion (&) AVCHD MP4 60P 35 Mbps MXP, FXP, LP 24 Mbps, 17 Mbps - 4 Mbps Video quality after conversion ( ) Cannot be converted. 24 Mbps, 17 Mbps, 4 Mbps The video quality will remain at 4 Mbps.
POINTS TO CHECK • Before installing the software, make sure your computer is connected to the Internet. Installation 1 Download the zip file from PIXELA’s Web site. Visit the PIXELA’s site to download the zip file, which contains the software and instruction manual. http://pixela.jp/cetule_dl/ 2 Uncompress the zip file. The zip file contains the installer (setup.exe) and the Software Guide (PDF file). 3 Run the installer to install the software.
For details about using the software, refer to the Software Guide (PDF file) of the PIXELA’s software. Saving MP4 Movies and Photos (Windows/Mac OS) With the supplied software ImageBrowser EX you can save MP4 movies and photos to your computer and easily organize them. Refer to the ‘ImageBrowser EX User Guide’ (PDF file) for the full system requirements and other information. Installation Install the software before you connect the camcorder to the computer for the first time.
5 Follow the onscreen instructions to select your area (continent), country/ region and language. Available options will vary depending on your country/ region. 6 In the main installer panel, click [Easy Installation]. For Windows users, if a User Account Control dialog box appears, follow the instructions. 7 Follow the onscreen instructions to complete the installation. • During the installation process, you may be prompted to install Microsoft Silverlight. Follow the instructions to do so.
• Connection #-1. Refer to Connection Diagrams (A 104). • Camcorder: When the connection is successfully established, [USB Connection] appears on the screen. 4 Save the recordings onto the computer. Refer to relevant sections in the ‘ImageBrowser EX Instruction Manual’, which can be accessed through the ? menu on the upper right of the software’s screen. IMPORTANT • When the camcorder is connected to a computer: - Do not open the memory card slot cover and do not remove the memory card.
(PTP) allowing you to transfer photos (JPEG only) simply by connecting the camcorder to a computer using the supplied USB cable, without having to install the supplied software ImageBrowser EX. 6/4 Memory Save: Saving an Entire Memory onto an External Hard Drive You can easily save all the movies and photos you recorded onto a commercially available external hard drive connected directly to the camcorder*. You can also use the camcorder to play back your recordings directly from the hard drive.
Before disconnecting the external hard drive Before turning off or physically disconnecting the external hard drive, be sure to safely end the connection to the camcorder to avoid damage to your files. From the [External Hard Drive] screen: [Safely Remove Hard Drive] > [Yes] IMPORTANT • Make sure you power the camcorder with the compact power adapter before you save a memory to the external hard drive.
card), the folder name of memory save folders following the first one will end in a numerical suffix. • The index screen will appear. 5 Touch a recording to play it back. To switch to another memory save folder, touch [ ] and then select the memory save folder you with to play back. Repeat step 5. 6 When you have finished playing back, be sure to safely end the connection to the external hard drive before physically disconnecting it.
2 Press to set the camcorder to playback mode. 3 Connect the camcorder to the external hard drive using the optional UA-100 USB Adapter. Connection #-2. Refer to Connection Diagrams (A 104). 4 Initialize the external hard drive. > [ Other Settings] > q > [Initialize '] > [Initialize] > [Complete Initialization]1 > [Yes]2 > [OK] 1 2 Touch this option if you want to physically erase all the data rather than just clear the file allocation table of the hard drive.
Connecting 1 Power the camcorder using the compact power adapter. 2 Open the desired index screen (A 50, 93, 94). 3 Connect the camcorder to the digital video recorder using the supplied USB cable. Connection #-1. Refer to Connection Diagrams (A 104). 4 6/4 Camcorder: Select the memory that contains the scenes you want to copy. • Select an option other than [All (for PC only)]. • When the connection is successfully established, [USB Connection] appears on the screen.
3 Camcorder: Locate the scene you wish to copy and pause the playback shortly just before the desired scene. 4 Camcorder: Resume playback. By default, the date and time will be embedded in the output video signal. You can change this using the > > [Display Date/ Time] setting. 5 External recorder: Start recording when the scene you wish to copy appears; stop recording when it ends. 6 Camcorder: Stop playback. NOTES • Use an external Blu-Ray Disc recorder compliant with AVCHD ver. 2.
6/4 Wi-Fi Functions This chapter contains information about how to operate the Wi-Fi functions of your camcorder, starting with the Wi-Fi network setup needed to add your camcorder to an existing Wi-Fi network. Introduction to Wi-Fi When you use the camcorder’s Wi-Fi function to connect to a smartphone1, you can wirelessly save, play back and upload your recordings. You can even use a smartphone as a remote control and record using the device’s screen.
Wi-Fi connection Wirelessly connect the camcorder to your iOS or Android smartphone or computer3 and use the device’s Web browser to view recordings in the camcorder (A 126). 3 You can also use a computer connected via an access point. Smartphone or similar device Wi-Fi connection After you download the Movie Uploader app4, wirelessly connect the camcorder to an iOS device (A 128) to save, play back and upload your recordings.
IMPORTANT • Using an unprotected Wi-Fi network can expose your files and data to monitoring by unauthorized third parties. Be aware of the risks involved. NOTES • Do not open the memory card slot cover during the wireless connection. • While using Wi-Fi functions, the camcorder’s automatic power off function will be disabled.
About the camcorder’s Wi-Fi standard The camcorder’s Wi-Fi standard complies with the IEEE 802.11 b/g/n protocol and operates in the 2.4 GHz band. As such, the maximum data transfer rate is 11 Mbps for IEEE 802.11b, 54 Mbps for IEEE 802.11g, and 150 Mbps for IEEE 802.11n. Note that these are theoretical values and actual data transfer rates may differ.
>[ Remote Control+Streaming] • The camcorder’s SSID (network name) and password will appear. • The camcorder will be ready to connect with the smartphone. 2 Smartphone: Activate Wi-Fi in the settings screen. The network names of detected access points will appear. 3 Smartphone: Touch the access point with the same SSID as that of the one from step 1. 4 Smartphone: Enter the password. [Connected] will appear on the camcorder’s screen and the connection will be established.
Smartphone or similar device Operating modes: SCN 1 Camcorder: From any movie index screen, set the camcorder to connect with the smartphone. >[ Wi-Fi] > [ Playback via Browser] > [OK] • The camcorder’s SSID (network name) and password will appear. • The camcorder will be ready to connect with the smartphone. Y P O 2 Smartphone: Activate Wi-Fi in the settings screen. The network names of detected access points will appear.
For movies, the selected recording will start playing back. For photos, the photo will be displayed. 8 Smartphone: Touch to save the recording on the smartphone. 9 Smartphone: Touch when finished. 10 Camcorder: Touch [End] when finished. NOTES • The following types of MP4 scenes will be recognized as multiple files on other devices.
from the following site. http://itunes.com/apps/movieuploader 1 Camcorder: From any movie index screen, set the camcorder to connect with the iOS device. >[ Wi-Fi] > [ Movie Uploader] > [OK] • The camcorder’s SSID (network name) and password will appear. • The camcorder will be ready to connect with the iOS device. 2 iOS device: Touch Settings > Wi-Fi and then turn Wi-Fi on. The network names of detected access points will appear.
- Scenes recorded at a video quality other than 35 Mbps exceeding 1 hour Sharing Recordings with CANON iMAGE GATEWAY After you register for CANON iMAGE GATEWAY*, you will be able to access various Web services**. You will be able to upload movies and photos to online albums, share the albums on Twitter, upload movies to Facebook and YouTube, send links to your online albums by e-mail to friends and family, and more! To use this function, you will need an access point connected to the Internet.
• Account settings for YouTube, Facebook and Twitter (depending on the services you plan to use). Setting the Desired Web Services in the Camcorder Using the supplied software CameraWindow, log in to CANON iMAGE GATEWAY and set the Web services you want to use. Refer to ‘CameraWindow Instruction Manual’ for details on using the software. Operating modes: SCN 1 Camcorder: Open the [y Movie Playback] index screen for MP4 movies (A 50). Alternatively, you can open the [} Photo Playback] index screen (A 54).
6 Computer: Click Edit Web Services > Desired Web service > Edit > Follow the onscreen instructions and enter your account information for the selected Web service > Set > Finish. The camera settings screen will appear again. C Y P O 7 Computer: Select the Web service to set in the camcorder and then click . • Repeat to select multiple Web services. • The selected Web services will appear in the camera panel. • You can click Í and Î to change the order in which the Web services appear in the camcorder.
Available Web services* Web service What you can do CANON iMAGE GATEWAY Upload MP4 movies and photos to your online photo albums. Facebook You can upload movies and photos directly to Facebook. Twitter Share recordings on Twitter. You can post a link to your online photo album on your Twitter feed. YouTube You can upload movies directly to YouTube. E-mail notification You can send e-mail notifications with a link to your online photo album. You can even set up to 20 e-mail addresses.
>[ Wi-Fi] > [ To Web Service] > [OK] 2 When [Configuration completed] appears on the screen, touch [OK]. 3 Perform the procedure in Wi-Fi Connection Using an Access Point (A 137). [Connected] will appear on the camcorder’s screen and the connection will be established. 4 Select the desired Web service. • Select one of the available Web services other than e-mail. • You can send an e-mail notification of the when your movies and photos are uploaded (A 135).
• For movies, you can upload one at a time; for photos, up to 10 at a time. • Depending on the wireless router’s settings and capability, it can take some time to upload files. Sending Links to Recordings by E-mail After you upload movies and photos to online albums on CANON iMAGE GATEWAY, you can send links to those albums by e-mail to family and friends. Operating modes: SCN To set e-mail addresses in the camcorder You can set up to 20 e-mail addresses in the camcorder.
>[ Wi-Fi] > [ To Web Service] > [OK] 2 When [Configuration completed] appears on the screen, touch [OK]. 3 Perform the procedure in Wi-Fi Connection Using an Access Point (A 137). [Connected] will appear on the camcorder’s screen and the connection will be established. 4 Touch [ ]. 5 Perform steps 5 to 8 of Sharing Your Recordings Using Web Services (A 133). NOTES • E-mail addresses must consist of single-byte characters.
>[ Wi-Fi] > [ Media Server] > [OK] • If you have already performed this procedure before, the connection will be established automatically. Skip to step 4. 2 Camcorder: When [Save the access point] appears on the screen, touch [OK]. 3 Camcorder: Perform the connection in Wi-Fi Connection Using an Access Point (A 137). • [Connected] will appear on the camcorder's screen and the connection will be established.
General requirements • Correctly configured router that complies with the 802.11b/g/n protocol and is Wi-Fi certified (bears the logo shown on the right) and a home network. Operating modes: SCN Touch the desired connection method. Options [WPS: Button]* Simply press and hold the WPS button on your wireless router and then touch the camcorder’s screen. This is the easiest connection method if you are using a WPS-compatible router. For details, see Wi-Fi Protected Setup (WPS) (A 138).
[Search for Access Points] method. Refer also to the router’s instruction manual. 1 [WPS: Button] method Press and hold the WPS button on the wireless router. • Depending on the router, the amount of time required may differ. • Make sure the router’s WPS function is activated. [WPS: PIN Code] method From a computer or similar device connected to the wireless router, use the Web browser to open the router’s WPS settings screen.
4 Touch [OK]. After the connection is established, continue using the function you were previously using. For details, refer to Viewing and Changing Wi-Fi Settings (A 142) or Sharing Your Recordings Using Web Services (A 133), as necessary. Using the virtual keyboard When you need to enter text for various settings, touch the text field and a virtual keyboard will appear on the screen. The illustration below explains the various keys you can use.
In step 2, if you selected [OPEN NONE], this step is not necessary. 4 Touch [Automatic] or [Manual] to select how to obtain the IP address. If you selected [Automatic], proceed to step 11. 5 For both the IP address and subnet mask areas, touch [0.0.0.0] and then touch [Í]/[Î] to change the value. Touch and next field and change the value, as necessary. 6 Touch [OK] and then touch [Next]. 7 In the default gateway area, touch [0.0.0.0] and then touch [Í]/ [Î] to change the value.
1 From any movie index screen, open the setting selection screen. >[ Wi-Fi] > [w Check/Edit Settings] > [OK] To view the smartphone’s connection settings 2 Touch [Smartphone Connection Settings]. The camcorder’s SSID and password will appear. 3 If necessary, touch [Edit] > [OK] > [OK] to change the settings and then perform the procedure in Manual Setup (A 140). The next time you make a wireless connection, you will need to change the Wi-Fi settings in the smartphone.
Glossary This is a glossary of some of the basic terms used frequently in this chapter. The documentation for your wireless router may also contain a glossary you can refer to. Access Point A wireless access point (WAP) is a device that allows wireless devices, like your camcorder, to connect to a wired network (including to the Internet) using the Wi-Fi standard. In most cases, this will be your wireless router. IP Address Exclusive number assigned to each device connected to the network.
Additional Information This chapter contains troubleshooting advice, screen messages, handling and maintenance tips, and other information. Appendix: Menu Options Lists The functions that are available depend on the shooting mode. In the following tables, available functions are indicated by z and functions not available are indicated by –. On the camcorder’s screen, menu items not available appear grayed out. For details about how to select an item, refer to Using the Menus (A 35).
Control Button Setting options/Function SCN N A Zoom controls, [START]/[STOP] control z z z z z 48 [W] (tele macro): Toggle on or off – – z z z 85 [R Faders] [j Off], [T Fade Trigger], [V Wipe], [Black Screen], [White Screen] z – z z z 78 [Zoom Type] [ [ [ – – z z z 48 [È Powered IS] [ON], [OFF] – – z z z 76 [ZOOM] Optical], Advanced], Digital] [z Pre REC] [ON], [OFF] z – z z z 82 [< Focus] [D] (manual focus): Toggle on or off, Touch AF frame – – z z
[Edit] Panel - Mode Index Screen Playback Pause A 6/4 From the built-in memory: [Copy (&` )] , – 107 6/4 From the built-in memory: [Convert to MP4 (&` )] [Select] – 110 , [This Scene] 56 Control Button [Select], [All Scenes] [Delete] [Select], [All Scenes] [Divide] – z 99 [Trim] – z 100 [Edit] Panel - Mode Y P O Control Button Index Screen Single Photo View A 6/4 From the built-in memory: [Copy (&` )] , z 108 z 58 [
Menu item Setting options A [Face Detection & Tracking] [i On }], [j Off] 76 [Auto Backlight Correction] [i On], [j Off] 80 [Auto Slow Shutter] [i On], [j Off] – [Flicker Reduction] [j Off], [: 50 Hz], [; 60 Hz] – [Image Stabilizer] [ [Intelligent IS] [È With È], [ [Video Snapshot Length] Dynamic], [ Standard], [j Off] 75 Without È] 45 [C 2 sec], [D 4 sec], [F 8 sec] 74, 92 [Zoom Position at Startup]: Allows you to choose the position of the zoom when you turn on the camcorder.
s/ Playback Setup Menu item y Setting options A [Select Music] [j Off], [i On] When [i On] - list of music tracks, [Music Balance] [y] [Û] (Original sound/Background music) z z 95 [Slideshow Transition] [j Off], [k Dissolve], [l Slide Image] – z 101 [Video Snapshot Length] [C 2 sec], [D 4 sec], [F 8 sec] z z 74, 92 Display Setup Menu item [Onscreen Markers] Setting options Y P O [j Off], [3 Level (White)], [4 Level (Gray)], [5 Grid (White)], [6 Grid (Gray)] C [Display Date/Time] [
[Output Onscreen Displays]: When set to [i On], the camcorder’s onscreen displays will appear also on the screen of a TV or monitor connected to the camcorder. • This function is not available when the shooting mode is set to . [LCD Brightness]: Adjusts the brightness of the LCD screen. • Changing the brightness of the LCD screen does not affect the brightness of your recordings or the brightness of the playback image on a TV. [LCD Backlight]: Sets the screen to one of three brightness levels.
• This function is not available when the camcorder is connected to an HDTV using the supplied High Speed HDMI cable.
Menu item [Volume] v y Setting options [Speaker]: A – z z 52 z z z 89 ,Ú [Headphones]: ,Ö [Notification Sounds] [÷ High Volume], [ø Low Volume], [j Off] z z z – [Custom Control Button] Same as the [ Main Functions] panel (Default: [Ò Decoration]) z – – – [Battery Info] – z z z – [Displayed Units] [.
• Estimated figures about available movie recording time and available number of photos are approximate and based on the currently selected video quality and a photo size of 1920x1080. • In the information screen of a memory card you can also check its Speed Class. • 6/4 The [Total space] shown for the built-in memory indicates actually usable space. It may be slightly smaller than the nominal built-in memory capacity listed in the specifications.
• If the memory card you insert already contains a file with a larger number, a new file will be assigned a number one higher than that of the last file on the memory card. • We recommend using the [n Continuous] setting. • Folder names, on the other hand, appear in a format such as “101_0501”. The first three digits indicate the folder number and the last four digits indicate the month and day (May 1, for the example folder above).
Appendix: Onscreen Icons and Displays Recording Movies and modes (with the zoom control displayed) 1 Control button [PHOTO]: Take a photo (A 41, 93) 2 Smart AUTO* (A 43) 3 Zoom controls (A 48) 4 Total number of scenes / Total recording time 5 Memory operation (A 157) 6 Intelligent IS (A 45) 7 Remaining battery charge (A 157) * Available only in mode.
Recording Movies SCN and modes a Control button [ ]: Open the A (Home) menu (A 36) s Shooting mode (A 39) A d A Exposure (A 79) f A Focus (A 80) g A Face detection (A 76) h White balance (A 83) A j A Audio level indicator (A 87) k While recording/during playback: A Scene counter (hours : minutes : seconds); < Self timer (A 84) l Pre-recording (A 82) A q Image stabilizer (A 75) S a S Tele macro (A 85) s Movie format (A 60) S * 6/4 only.
Playing Movies (during playback) s D D d f D g D Playback control buttons (A 52) Scene playback time Scene number Date/Time (A 148) Viewing Photos C Y P O k D Control button [Edit]: Open the Edit panel (A 146) l D Current photo / Total number of photos q F File number (A 152) 156 Additional Information h Volume and background music D balance controls (A 52, 96) j Decoration (A 69) D a Control button [h]: Photo jump F (A 55) s Control button [Ð]: Slideshow F (A 101) d Control button [f]: Return to
5 Memory operation Ü Record, Û Record pause, Ð Playback, Ý Playback pause, × Fast playback, Ø Fast reverse playback, Õ Slow playback, Ö Slow reverse playback, Ó Frame advance, Ô Frame reverse. 7 Remaining battery charge • The icon shows a rough estimate of 100% 75% 50% 25% 0% the remaining charge as a percentage of the full charge of the battery pack. • When the battery charge becomes low, replace or charge the battery pack.
Trouble? Troubleshooting If you have a problem with your camcorder, refer to this section. Sometimes what you think is a malfunction of the camcorder may have the simplest of solutions - please read the “CHECK THIS FIRST” box before going on to the more detailed problems and solutions. Consult your dealer or a Canon Service Center if the problem persists.
- If you are using a battery pack recommended by Canon for use with this camcorder, there may be a problem with the camcorder or battery pack. Consult a Canon Service Center. A noise can be heard from the compact power adapter. - A faint sound can be heard while the compact power adapter is connected to a power outlet. This is not a malfunction. The battery pack is exhausted extremely quickly even at normal temperatures. - The battery may have reached the end of its battery life. Buy a new battery pack.
After using the camcorder for a long time, it becomes hot. - The camcorder may become hot after using it continuously for long periods of time; this is not a malfunction. If the camcorder becomes unusually hot or it becomes hot after using it only for a short while, it may indicate a problem with the camcorder. Consult a Canon Service Center. Playback Cannot delete a scene. - You may not be able to delete scenes recorded or edited using another device. Deleting scenes takes longer than usual.
Indicators and Onscreen Displays lights up in red. - Battery pack is exhausted. Replace or charge the battery pack. appears on the screen. - The camcorder cannot communicate with the battery pack attached so the remaining battery charge cannot be displayed. lights up in red. - A memory card error occurred. Turn off the camcorder. Remove and reinsert the memory card. Initialize the memory card if the display does not change back to normal. - The memory card is full.
Abnormal characters appear on the screen and the camcorder does not operate properly. - Disconnect the power source and reconnect it after a short time. If the problem still persists, remove the battery pack and disconnect all other power sources from the camcorder. Then, reset all the camcorder’s settings to default values (A 151). Video noise appears on screen. - Keep a distance between the camcorder and devices that emit strong electromagnetic fields (plasma TVs, cellular phones, etc.).
Connections with External Devices Video noise appears on the TV screen. - When using the camcorder in a room where a TV is located, keep a distance between the compact power adapter and the power or antenna cables of the TV. Playback looks fine on the camcorder but there is no image on the TV screen. - The video input on the TV is not set to the video terminal to which you connected the camcorder. Select the correct video input.
- Wi-Fi networks with a stealth function that do not broadcast their network name (SSID) will not be detected by the camcorder during the Wi-Fi network setup. Perform the setup manually (A 140) or turn off the stealth function of the wireless router. Wireless playback on a computer or similar device is not smooth. - Playback may not be smooth depending on the wireless router’s settings and capability. - Connect the computer to the access point using a LAN cable.
6/4 Built-in memory is full - The built-in memory is full ([& End] appears on the screen). Delete some recordings (A 56, 58) to free some space. Alternatively, save your recordings (A 111) and initialize the built-in memory (A 33). 6/4 Built-in memory writing error Attempt to recover the data? - This message will appear the next time you turn on the camcorder if power supply was accidentally interrupted while the camcorder was writing to the built-in memory.
6/4 Cannot play back Cannot access the built-in memory - There is a problem with the built-in memory. Save your recordings (A 111) and initialize the built-in memory using the [Complete Initialization] option (A 33). If the problem persists, contact a Canon Service Center. Cannot play back Check the memory card - There is a problem with the memory card. Save your recordings (A 111) and initialize the memory card using the [Complete Initialization] option (A 33).
Cannot record movies on this memory card Initialize only using the camcorder - The memory card in the camcorder was initialized using a computer. Initialize the memory card with this camcorder (A 33). Cannot save the canvas - Cannot save your [Pens and Stamps] drawings on the memory. Save your recordings (A 111) and initialize the memory (A 33). Cannot trim the scene - You cannot trim scenes that were recorded using another device or copied to an SDXC memory card.
Do not disconnect the power source. Do not disconnect the USB cable unless you first use the computer to safely end the connection. - When the camcorder is in mode and is connected to the computer with the supplied USB cable, the camcorder cannot be operated. Disconnecting the USB cable or power source while this message appears may result in permanent loss of the recordings in the camcorder.
Memory card writing error Attempt to recover the data? - This message will appear the next time you turn on the camcorder if power supply was accidentally interrupted while the camcorder was writing to the memory. Select [Recover] to try to recover the recordings. If you inserted a memory card that contains scenes recorded using another device, we recommend that you select [No]. Need to recover files from the memory card. Change the position of the LOCK switch on the memory card.
Some scenes could not be deleted - Movies that were protected/edited with other devices cannot be deleted with this camcorder. Some scenes were recorded using another device and cannot be copied. - Scenes that were not recorded with this camcorder cannot be copied to the memory card. Task in progress. Do not disconnect the power source. - The camcorder is updating the memory. Wait until the operation ends and do not disconnect the compact power adapter or remove the battery pack.
The compact power adapter was disconnected. Could not safely remove the external hard drive. - While the camcorder was connected to an external hard drive, the camcorder’s compact power adapter was disconnected and the connection was ended. Check whether data in the hard drive was corrupted. 6/4 List of Messages for Wi-Fi Functions Refer also to the instruction manual of your wireless router and other devices you will use. Another user is already controlling the camcorder. Try again later.
Unable to complete WPS. - Turn off the camcorder and wireless router. After a short while, turn them on again and try again. If the problem persists, perform setup using the [Search for Access Points] option (A 137). Unable to connect - Cordless phones, microwave ovens, refrigerators and other appliances may interfere with the wireless signal. Try using the camcorder in a location farther away from such appliances.
Wi-Fi error Incorrect encryption method - Make sure the camcorder and access point are using the same authentication/encryption method. - If the access point is using MAC address filtering, enter the camcorder’s MAC address in the access point’s configuration screen. Wireless communication is not working correctly - Cordless phones, microwave ovens, refrigerators and other appliances may interfere with the wireless signal. Try using the camcorder in a location farther away from such appliances.
Try again - An error occurred when connecting to the CANON iMAGE GATEWAY server or the server is temporarily down. End the Wi-Fi connection and try again.
Do’s and Don’ts Handling Precautions Camcorder Be sure to observe the following precautions to ensure maximum performance. • Save your recordings periodically. Make sure to transfer your recordings to an external device such as a computer or digital video recorder (A 107) and save them on a regular basis. This will protect your important recordings in case of damage and create more free space on the memory. Canon shall not be liable for any data loss. • Do not carry the camcorder by the LCD panel.
• Do not use or store the camcorder in dusty or sandy places. The camcorder is not waterproof – avoid also water, mud or salt. If any of the above should get into the camcorder it may damage the camcorder and/or the lens. • Be careful of heat generated by lighting equipment. • Do not disassemble the camcorder. If the camcorder does not function properly, consult qualified service personnel. • Handle the camcorder with care. Do not subject the camcorder to shocks or vibration as this may cause damage.
• Dirty terminals may cause a poor contact between the battery pack and the camcorder. Wipe the terminals with a soft cloth. Long-term storage • Store battery packs in a dry place at temperatures no higher than 30 °C (86 °F). • To extend the battery life of the battery pack, discharge it completely before storing it. • Charge and discharge all your battery packs fully at least once a year.
• Secure Digital (SD) memory cards have a physical switch to prevent writing on the card so as to avoid the accidental erasure of the card’s content. To write-protect the memory card set the switch to the LOCK position. LOCK switch Built-in Rechargeable Lithium Battery The camcorder has a built-in rechargeable lithium battery to keep the date/time and other settings.
Maintenance/Others Cleaning Camcorder Body • Use a soft, dry cloth to clean the camcorder body. Never use chemically treated cloths or volatile solvents such as paint thinner. Lens • If the lens surface is dirty, autofocus may not work properly. • Remove any dust or dirt particles using a non-aerosol type blower brush. • Use a clean, soft lens-cleaning cloth to gently wipe the lens. Never use tissue paper. LCD Touch Screen • Clean the LCD touch screen using a clean, soft lens-cleaning cloth.
• Remove the memory card and battery pack. Then, place the camcorder in an airtight plastic bag and let it adjust gradually to temperature changes before removing it from the bag. When condensation is detected The precise time required for water droplets to evaporate will vary depending on the location and weather conditions. As a general rule, wait for 2 hours before resuming use of the camcorder.
General Information Accessories (Availability differs from area to area) Printer Card reader/writer Computer External hard drive** C Y P O TV/HDTV Digital video recorder Optional accessories not listed below are described in more detail in the following pages. CA-110 Compact Power Adapter Memory card 6 IFC-300PCU/S* or IFC-400PCU USB Cable 1 5 HTC-100/S* or HTC-100 High Speed HDMI Cable 9 STV-250N Stereo Video Cable 8 * Supplied with the camcorder; not available as an optional accessory.
Optional Accessories Call or visit your local retailer/dealer for genuine Canon video accessories. You can also obtain genuine accessories for your Canon camcorder by calling: 1-800-828-4040, Canon U.S.A. Information Center. Use of genuine Canon accessories is recommended. This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc.
Battery pack→ BP-718 Charging conditions↓ BP-727 Using the camcorder 335 min. 465 min. Using the CG-700 Battery Charger 220 min. 315 min. Recording and playback times given in the following tables are approximate and vary according to video quality and charging, recording or playback conditions. The effective usage time of the battery pack may decrease when recording in cold surroundings, when using the brighter screen settings, etc.
Battery pack BP-727 Video quality Recording (maximum) Recording (typical)* Playback 60P 135 min. 80 min. 215 min. MXP 145 min. 85 min. 230 min. FXP 145 min. 85 min. 235 min. LP 150 min. 85 min. 240 min. 6/4 Recording MP4 movies using the built-in memory Battery pack BP-718 BP-727 Recording (maximum) Recording (typical)* Playback 35 Mbps 90 min. 50 min. 145 min. 24 Mbps 110 min. 60 min. 160 min. Video quality 17 Mbps 110 min. 60 min. 160 min. 4 Mbps 115 min. 65 min.
4 WM-V1 Wireless Microphone Reliably record rich sound even when shooting subjects at a distance. The transmitter is conveniently equipped with a clothing clip and the receiver can be attached to the camcorder’s grip belt. 7 UA-100 USB Adapter 6/4 Allows you to connect to the camcorder an external hard drive or similar storage device with a standard-A cable. After doing so, you can save an entire memory onto the device. Check in advance the USB cable supplied with your external hard drive.
Specifications VIXIA HF R42 / VIXIA HF R40 / VIXIA HF R400 — Values given are approximate figures. System • Recording System Movies: AVCHD* Video: MPEG-4 AVC/H.264; Audio: Dolby Digital 2ch MP4 Video: MPEG-4 AVC/H.264 Audio: MPEG-2 AAC-LC (2ch) Photos: DCF (Design rule for Camera File system), compatible with Exif** Ver. 2.3 Image compression: JPEG * Compatible with AVCHD ver. 2.0 specifications. ** This camcorder supports Exif 2.3 (also called “Exif Print”).
MP4 movies: 35 Mbps: 1 hr. 4 Mbps: 8 hr. 40 min. 24 Mbps: 1 hr. 25 min. 17 Mbps: 2 hr. 5 min. • Image Sensor 1/4.85-in. CMOS, 3,280,000 pixels Effective pixels: 2,070,000 pixels (1920 x 1080) When advanced zoom is on: 1920 x 1080 (wide angle) 1360 x 765 (full telephoto) • LCD Touch Screen: 3 in., wide, TFT color, 230,000 dots, touch operation • Microphone: Stereo electret condenser microphone • Lens f=2.8-89.6 mm, F/1.8-4.5, 32x optical zoom, 53x advanced zoom 35 mm equivalent: 38.5 – 1,232 mm 32.
• USB Terminal: mini-AB, Hi-Speed USB • HDMI OUT Terminal HDMI Mini Connector; output only • MIC Terminal ∅ 3.5 mm stereo minijack –64 dBV (with 600 Ω microphone) / 5 kΩ or more Wi-Fi (6/4 only) • Standard: Complies with the IEEE 802.11b/g/n protocol; Wi-Fi Protected Setup (connection methods: WPS button, PIN code) • Frequency: 2.4 GHz • Supported channels: 1 - 11 • Encryption methods: WEP-64/WEP-128, TKIP/AES Power/Others • Power supply (rated) 3.6 V DC (battery pack), 5.
BP-718 Battery Pack • Battery type Rechargeable lithium ion battery • Rated voltage: 3.6 V DC • Operating temperature: 0 – 40 °C (32 – 104 °F) • Battery capacity: 1,840 mAh (typical); 6.5 Wh / 1,790 mAh (minimum) • Dimensions: 30.3 x 24.9 x 40.1 mm (1.2 x 0.98 x 1.6 in.) • Weight: 42 g (1.
About the music files The specifications of the music files compatible with the camcorder are as follows. Audio encoding: Linear PCM Audio sampling: 48 kHz, 16 bits, 2 channels Minimum length: 1 second File type: WAV The music data is saved in the memory under the following folders. 6/4 In the built-in memory: \CANON\MY_MUSIC\MUSIC_01.WAV to MUSIC_99.WAV On the memory card: \CANON\PRIVATE\MY_MUSIC\MUSIC_01.WAV to MUSIC_99.
Index 60P recording . . . . . . . . . . . . . . . . 60 A Abroad, using the camcorder . . . . 180 Aspect ratio of a connected TV (TV type) . . . . . . . . . . . . . . . 149 Audio recording level . . . . . . . . . . . 87 Audio scene select . . . . . . . . . . . . 86 AUTO mode . . . . . . . . . . . . . . . . . 41 Auto slow shutter . . . . . . . . . . . . 147 Automatic backlight correction . . . . 80 AV OUT/× terminal . . . . 89, 102, 104 B Baby album . . . . . . . . . . . . . . . . . . 93 Baby mode . . . . .
Low light (Special Scene mode) . . .68 S M Saving recordings . . . . . . . . . . . . 107 Transferring to a computer Main Functions panel . . . . . . .38, 144 Maintenance . . . . . . . . . . . . . . . . 179 Markers . . . . . . . . . . . . . . . . . . . . 148 Memory card . . . . . . . . . . . . .27, 177 Memory save* . . . . . . . . . . . . . . . 116 MIC terminal . . . . . . . . . . . . . . . . .91 Movie format (AVCHD/MP4) . . . . . .39 Movie Uploader* . . . . . . . . . . . . .
Wi-Fi functions* . . . . . . . . . . . . . . 122 Z Y Zoom . . . . . . . . . . . . . . . . . . . . . . 47 Advanced zoom . . . . . . . . . . . 47 Zoom speed . . . . . . . . . . . . . 47 YouTube . . . . . . . . . . . . . . . . . . . 121 C Y P O * 6/4 only.
USA CANON CONSUMER DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY FOR THE UNITED STATES The limited warranty set forth below is given by Canon U.S.A., Inc. (“Canon USA”) with respect to Canon Consumer Digital Video Equipment (the “Equipment”) purchased in the United States. This limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase.
LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE EQUIPMENT’S HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON USA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
CANADA CANON CONSUMER DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY The limited warranty set forth below is given by Canon Canada Inc. (“Canon Canada”) with respect to Canon Consumer Digital Video Equipment (the “Equipment”) purchased in Canada. This limited warranty is only effective upon presentation of a bill of sale or other proof of purchase for this Equipment to a Canon Service Facility when repairs are required.
CANON U.S.A., INC. NEW JERSEY OFFICE 100 Jamesburg Road, Jamesburg, NJ 08831 USA CANON U.S.A., INC. CHICAGO OFFICE 100 Park Blvd., Itasca, IL 60143 USA CANON U.S.A., INC. LOS ANGELES OFFICE 15955 Alton Parkway, Irvine, CA 92618 USA CANON U.S.A., INC. HONOLULU OFFICE 210 Ward Avenue, Suite 200, Honolulu, Hl 96814 USA USA ❖ If you have any questions, call the Canon U.S.A. Information Center toll-free at 1-800-828-4040 (USA only). CANON CANADA INC.