Wireless File Transmitter WFT-E7 C Y P O To comply with local radio wave regulations, Canon offers five region-specific versions of the transmitter (WFT-E7A, E7B, E7C, E7D, and E7E) in various areas around the world. (See Areas of Use and Restrictions.) For convenience, we refer to the product in this manual simply as “the transmitter,” without reference to versions A, B, C, D, or E.
Thank you for purchasing a Canon product. The Wireless File Transmitter WFT-E7 is an accessory for EOS cameras. In addition to time synchronization with other cameras (over a wireless or wired LAN connection) and Bluetooth connectivity with GPS devices, the transmitter enables the following operations.
Sync the Camera Time over a Wireless or Wired Connection Slave camera Slave camera LAN cable Master camera Slave camera Hub Master camera LAN cable Y P O Master camera Connect to GPS Devices (commercially available) via Bluetooth C Connected via Bluetooth Add the latitude, longitude, altitude, date and time, and other shooting information to images 3
Conventions Used in this Manual These instructions assume that your wireless or wired LAN and FTP server settings are complete. For details on configuring these settings, refer to the documentation provided with the respective equipment. Terms in brackets [ ] indicate button or icon names or other software elements. Brackets also denote camera menu items. The EOS 5D Mark III is used as an example for illustrations and screens in this manual.
Chapter List Introduction 2 1 Basic Network Settings 17 2 Transferring Images to an FTP Server 31 3 Remote Capture Using EOS Utility 47 4 Remote Capture Using WFT Server 53 5 Using the Transmitter as a Media Server 6 Linked Shooting 7 Managing Settings Information 83 8 Synchronizing the Camera Time 89 9 Using Bluetooth GPS Devices 93 10 Troubleshooting 97 11 Reference C Y P O 65 69 113 5
Contents Introduction Conventions Used in this Manual ...................................................................................................... 4 Chapter List........................................................................................................................................ 5 Contents............................................................................................................................................. 6 Safety Warnings...................................
Contents 6 7 Linked Shooting 69 Preparing Slave Cameras................................................................................................................ Basic Linked Shooting ..................................................................................................................... Positioning the Slave Cameras........................................................................................................ Using the Transmitter with WFT Server............................
Safety Warnings The following precautions are intended to prevent harm to you and others as well as damage to equipment. Become familiar with the precautions before using the transmitter to ensure correct and safe operation. Be sure that you fully understand the safety precautions contained in the instruction manuals for the battery, charger, and AC Adapter Kit before using them.
Nomenclature For detailed information, reference page numbers are provided in parentheses (p.**). Tripod screw Power lamp (p.14) Battery compartment cover release lever (p.11) Battery compartment cover (p.11) lamp LCD panel (p.10) Power switch (p.14) C port (p.
Nomenclature LCD panel Connection icon Error number Wired LAN connection Wireless signal strength Battery check Bluetooth connection Case Belt holder Strap mounts Case strap C Y P O Case for tripod screw Interface cables Approx. 25 cm / 9.8 in. 10 Approx. 1.5 m / 4.9 ft.
Installing and Removing the Battery Use one Battery Pack LP-E6 to power the transmitter. When replacing the transmitter’s battery, be sure to turn the transmitter off before opening the battery compartment cover. Also note that the transmitter is not sold with a battery or charger. If you do not own these accessories, they are available for purchase separately. Installing the battery 1 Open the cover. 2 Insert the battery. 3 Close the cover. Push the lever down and open the cover.
Installing and Removing the Battery Battery check The remaining battery power is displayed when you turn the transmitter on. A blinking battery icon ( ) indicates that the battery will be depleted soon. Icon Level (%) 100 – 70 69 – 50 49 – 20 19 – 10 Number of images that can be transferred LAN At Normal Temperature (23°C / 73°F) Wireless LAN 2400 Wired LAN 2200 9–1 0 Approx. number of images At Low Temperature (0°C / 32°F) Y P O 2300 2200 When using a fully charged LP-E6.
Using a Household Power Outlet When the AC Adapter Kit ACK-E6 (sold separately) is used, a household power outlet can be used to power the transmitter without worrying about the battery level. 1 Connect the DC coupler plug. 2 Connect the power cord. 3 Insert the DC coupler. Connect the DC coupler plug to the socket of the AC adapter. Connect the power cord as shown. Insert the plug into the outlet. After usage, unplug from the outlet.
Attaching to the Camera When connecting the transmitter to the camera, always use one of the interface cables included with the transmitter. 1 Turn off both the camera and transmitter. 2 Attach the transmitter’s port cap. 3 Connect the transmitter and camera. To keep the cable securely connected, attach the cap to the transmitter. C 4 Y P O Connect the end of the cable with the logo to the transmitter’s terminal.
Attaching to the Camera Example of Attachment Y P O Example of Using the Case and Strap C If you turn on/off the transmitter or connect/disconnect the interface cable during Live View shooting or movie shooting, Live View shooting or movie shooting will stop.
Subsequent Organization of This Manual Click one of the following chapter titles to view the corresponding page. 1 Basic Network Settings (p.17) 2 Transferring Images to an FTP Server (p.31) 3 Remote Capture Using EOS Utility (p.47) 4 Remote Capture Using WFT Server (p.53) 5 Using the Transmitter as a Media Server (p.65) 6 Linked Shooting Y P O 7 Managing Settings Information C 16 (p.69) (p.83) 8 Synchronizing the Camera Time (p.89) 9 Using Bluetooth GPS Devices (p.
Basic Network Settings Y P O Complete the basic network settings by following the transmitter’s connection instructions on the camera menu screen.
Getting Ready [FTP trans.], [EOSUtility], [WFTserver] The connection instructions help you follow the steps to connect the transmitter to an existing wireless or wired LAN. To connect to a wireless LAN, prepare the wireless LAN terminal (wireless LAN access point or wireless LAN adapter) and computer in advance so that they are ready for you to connect the transmitter to the wireless network. When configuring the basic network settings, bring the transmitter within 3 m / 9.8 ft.
Displaying the Connection Wizard This section’s explanation follows the flow of the connection instructions. If an error is displayed, see “Troubleshooting” in Chapter 10 (p.97) and check the settings. Pressing the shutter button or other camera controls during configuration will cause the connection instructions to close. Do not press the shutter button or other controls until configuration is finished. In the menu, set [Auto power off] to [Disable].
Selecting the Communication Method and LAN Type Selecting the Communication Method Turn the <5> dial to select the communication method, and then press <0>. Select [OK] and press <0> to go to the next screen. • FTP trans. Select this option to transfer captured images to an FTP server. Images can be automatically transferred as you shoot them, or you can select images to be transferred later. Computer Operating Systems Use of [FTP trans.
Selecting the Communication Method and LAN Type • WFTserver Select this option for remote capture over a wireless or wired LAN with the transmitter acting as a server. Additionally, images on a memory card in the camera can be viewed and downloaded to a computer. The camera can be accessed in the same way as browsing a web page, by users at up to three computers. Computer Operating Systems Any computer with a web browser can be used, regardless of the operating system.
Selecting the Communication Method and LAN Type Selecting the LAN Type For [LinkedShot] instructions, see page 69. Note that no information about [LinkedShot] is given in this chapter. Turn the <5> dial to select the type of LAN, and then press <0>. Select [OK] and press <0> to go to the next screen. Wireless LAN The [Wireless LAN setup method] screen is displayed. [Connect with wizard]: See p.23 [WPS (PBC mode)]: See p.25 [WPS (PIN mode)]: See p.
Using the Wizard to Establish a Connection Selecting the Wireless Network When you select [Connect with wizard], active wireless LAN terminals in your area are listed, accompanied by their respective information. Select the SSID (or ESS-ID) of your desired wireless LAN terminal. 1 2 3 4 1 Select [Connect with wizard]. 2 Select the wireless LAN terminal. Turn the <5> dial to select [Connect with wizard], and then press <0>. To select the wireless LAN terminal, press <0>.
Using the Wizard to Establish a Connection Entering the Wireless LAN Encryption Key Enter the encryption key set for the wireless LAN terminal. For details on the encryption key, refer to the device’s instruction manual. Note that the screens displayed in steps 1 to 3 below vary depending on the authentication and encryption of the wireless LAN terminal. 1 The [Key index] screen is displayed only if WEP encryption is used by the wireless LAN terminal.
WPS Connections (PBC Mode) This is a connection mode when using a wireless LAN terminal compatible with Wi-Fi Protected Setup (WPS). Pushbutton Connection mode (PBC mode) makes it easy to establish a connection between the camera and the wireless LAN terminal by pressing the WPS button on the wireless LAN terminal. Note that if multiple wireless LAN terminals are active in your area, it may be harder to establish a connection. In this case, try using [WPS (PIN mode)] to establish a connection.
WPS Connections (PIN Mode) This is a connection mode when using a wireless LAN terminal compatible with Wi-Fi Protected Setup (WPS). In PIN code connection mode (PIN mode), an 8-digit identification number specified on the camera is set on the wireless LAN terminal to establish a connection. Even if there are multiple wireless LAN terminals active in your area, this is a relatively reliable method of establishing a connection using a shared identification number.
Configuring Network Settings Turn the <5> dial to select a configuration method for the network settings, and then press <0>. Select [OK] and press <0> to go to the next screen. [Auto setting] Settings otherwise configured with [Manual setting] can be configured automatically. However, the IP address and similar settings must be automatically assigned and configured in environments using DHCP servers or wireless LAN terminals or routers supporting DHCP server functions.
Configuring Network Settings Completing Settings for the Communication Method The following instructions are for setting screens that vary depending on the communication method (FTP Transfer, EOS Utility, WFT Server, or Media Server), as shown below. Read the page that describes the selected communication method. FTP trans. Chapter 2 (p.31) EOSUtility Chapter 3 (p.47) C Y P O Windows 7 and Windows Vista Users Before performing the operations described from page 47, perform the operations below.
Configuring Network Settings Virtual Keyboard Operation The virtual keyboard is displayed when entering the encryption key, server name, and other information. Switching between input areas To switch between input areas, press the button. Moving the cursor To move the cursor, turn the <5> dial. You can also move the cursor using <9>. Entering text In the bottom input area, turn the <5> dial to move the cursor and press <0> to enter text. You can also move the cursor using <9>.
C 30 Y P O
Transferring Images to an FTP Server Y P O With FTP transfer, you can automatically transfer each image to the FTP server as you shoot or transfer images in batches after shooting.
Configuring FTP Communication Settings These instructions are continued from Chapter 1. 1 Turn the <5> dial to select [Address setting], and then press <0>. 2 If you set the DNS server setting to [Disable], the screen on the left is displayed. Press <0> to select the input position, and then turn the <5> dial to enter the IP address of the FTP server. If you set the DNS server IP address setting to [Auto assign] or [Manual setting], the screen on the left is displayed.
Configuring FTP Communication Settings 6 Complete the [Login method] settings. Turn the <5> dial to select [OK], and then press <0> to go to the next screen. 7 Complete the [Target folder] settings. Select [Root folder] to save images in the root folder as specified in FTP server settings (p.86). Select [Select folder] to specify a subfolder in the root folder. If no folder exists, a folder will be created automatically. Turn the <5> dial to select [OK], and then press <0> to connect to the FTP server.
Automatic Image Transfer After Each Shot An image can be automatically transferred to the FTP server immediately after shooting. You can continue still photo shooting while images are being transferred. Before shooting, be sure to insert a memory card in the camera. If you shoot without recording images, they will not be transferred. Note that automatic transfer of movies is not supported. Transfer movies after shooting, as described on pages 37-44. 1 Select [Communication settings].
Automatic Image Transfer After Each Shot Setting the Size or Type of Images to Transfer With automatic transfer, you can select which images to transfer when recording images of different sizes to CF and SD cards, or when recording both RAW and JPEG images. 1 Select [Communication settings]. 2 3 Select [Network settings]. Select [Set up]. Y P O 4 C Select [Transfer type/size]. 5 Select the size and type of images to transfer.
Automatic Image Transfer After Each Shot To transfer smaller JPEGs when the camera is set up to record larger JPEGs to one card and smaller JPEGs to the other, set [JPEG size to trans.] to [Smaller JPEG]. To transfer either RAW or JPEG images when the camera is set up to record RAW images to one card and JPEGs to the other, specify which images to transfer in the [RAW+JPEG transfer] setting. Similarly, complete the same setting when RAW+JPEG images are recorded simultaneously to a single memory card.
Transferring Images Individually Simply select an image and press <0> to transfer it. You can add a caption before transferring the image. You can continue still photo shooting even while images are being transferred. Transferring the Current Image 1 Select [Communication settings]. 2 3 Select [Network settings]. Select [Set up]. C Y P O 4 Select [Transfer with SET]. 5 Select the image. Select [Enable]. Press the button on the camera.
Transferring Images Individually Adding a Caption Before Transfer You can add a registered caption to each image before transfer. This is convenient if you want to inform the recipient of the quantity to print, for example. The caption is also added to images stored on the camera. For instructions on creating and registering captions, see page 114. You can check the captions added to images in the user comments included in the Exif information. 1 2 Take the picture. 3 4 Select [Network settings].
Transferring Images Individually 5 Select a caption. 6 Transfer the image. Turn the <5> dial to select the [Caption] box, and then press <0>. Turn the <5> dial to select the caption content, and then press <0>. C Turn the <5> dial to select [Transfer], and then press <0>.
Batch Transfer After shooting, you can select multiple images as desired and transfer them all at once. You can transfer unsent images or images whose transfer failed previously. You can continue still photo shooting even while images are being transferred. Selecting Images to Transfer 1 In the menu, select [Image transfer]. 2 Select [Image sel./transfer]. 3 Select [Sel.Image]. 4 Select images to transfer. Y P O X An image is displayed.
Batch Transfer 5 Transfer the images. Select [Direct transfer]. Select [OK] on the confirmation screen displayed next. X A transfer progress screen is displayed. [RAW+JPEG transfer] Options Selecting [RAW+JPEG transfer] in step 2 on the preceding page will give you the option of transferring RAW images, JPEG images, or both types of images. The options will be the same whether you specify [Sel. Image], [Sel. n], or [All image] as the image selection method.
Batch Transfer Batch Transfer of Images in a Folder 1 In the menu, select [Image transfer]. 2 3 Select [Image sel./transfer]. 4 Select [Folder images not transfer’d]. 5 Select a folder. Select [Sel.n]. C 42 Y P O To transfer images whose transfer previously failed, select [Folder images failed transf.].
Batch Transfer 6 Transfer the images. Select [Direct transfer]. Select [OK] on the confirmation screen displayed next. X A transfer progress screen is displayed. C Y P O Selecting [Clear folder transf. history] will set the transfer history of images in the selected folder to “unsent.” This enables you to resend all the images in the folder later by selecting [Folder images not transfer’d].
Batch Transfer Batch Transfer of Images on Memory Cards 1 In the menu, select [Image transfer]. 2 3 Select [Image sel./transfer]. 4 Select [Card images not transferred]. 5 Transfer the images. Select [All image]. C Y P O To transfer images whose transfer previously failed, select [Card images failed transfer]. Select [Direct transfer]. Select [OK] on the confirmation screen displayed next. X A transfer progress screen is displayed. Selecting [Clear card’s transf.
Checking Image Transfer History Checking the Transfer History of Individual Images To check the transfer history in [Image sel./transfer], select [Sel.Image]. Image not selected for transfer (no mark) Image selected for transfer Image whose transfer failed Y P O Image already transferred C Checking the Transfer History of Memory Cards On the [Image sel./transfer] screen, you can check the number of images to be transferred as well as the transfer history of images in the memory card.
C 46 Y P O
Remote Capture Using EOS Utility Y P O You can use EOS Utility to shoot remotely over a wireless or wired LAN. As a wireless or wired network is used instead of the USB cable, all camera operations in EOS Utility are supported, in addition to remote capture. C The WFT-E7 wired or wireless LAN functions cannot be used with the Mac version of EOS Utility (as of November 2011). Check the Canon website for the latest system requirements, including supported OS versions.
Configuring EOS Utility Communication Settings These instructions are continued from Chapter 1. With EOS Utility, you can use the included WFT Pairing Software to establish a connection between the transmitter and a computer. WFT Pairing Software is installed automatically during easy installation of the software provided with the camera. If it is not installed, install it on the computer that will communicate with the transmitter before this procedure.
Configuring EOS Utility Communication Settings 3 Double-click the pairing software icon. X Detected cameras are listed. If a camera is already connected, it is not displayed in the list. Click [Connect]. If multiple cameras are displayed, identify the camera to connect to by its [MAC address] or [IP address]. You can check the [MAC address] and [IP address] by accessing [Confirm settings] in the menu (p.84).
Configuring EOS Utility Communication Settings There is no need to complete pairing again if you continue using a particular camera, transmitter, and computer together after pairing without changing the settings. When using this function the next time, simply turn on the camera to which the transmitter is attached and start the pairing software. The connection between the camera and computer will be established automatically.
Using EOS Utility For EOS Utility instructions, refer to the Software Instruction Manual (PDF). You can take full advantage of EOS Utility via the transmitter just as via a USB connection, without restrictions. C Y P O In Remote Live View shooting, the rate of image transmission is slower than via USB. The motion of moving subjects cannot be displayed smoothly.
C 52 Y P O
Remote Capture Using WFT Server Y P O Using a web browser, you can view images recorded on a memory card in the camera and download them to a computer. Additionally, you can shoot remotely over a wireless or wired LAN. Note that bulb, mirror lockup, and movie shooting are not supported.
Configuring WFT Server Communication Settings These instructions are continued from Chapter 1. Press <0> and turn the <5> dial to select the set number, and then press <0>. Press <0> again. After the connection wizard closes, the display will return to the menu screen. X The lamp on the transmitter lights up green. Settings information is stored on the camera. It is not stored on the transmitter. Setting up an Account Y P O Enter a login name and password to access the camera from a computer.
Configuring WFT Server Communication Settings 3 Turn the <5> dial to select [WFT account], and then press <0>. When changing the port number, turn the <5> dial to select [Port number] and press <0>. Note that there is normally no need to change the port number (80). 4 Select a user number. With WFT Server, you can connect the camera to up to three computers. Here, select a user number to prevent conflicts when users at other computers are connected to the transmitter simultaneously.
Displaying WFT Server In the web browser, display WFT Server, a screen for transmitter operations. Make sure you have already established a connection between the camera and computer. 1 2 3 Start the web browser. First, start Internet Explorer or another web browser. Enter the URL. In the address bar, enter the IP address assigned to the camera. Press the key. Enter the [Login name] and [Password]. Enter the login name and password as specified in the procedure on page 55.
Viewing Images You can browse the images recorded on the camera’s memory card. 1 Click [Viewer]. 2 Select the memory card. X The image viewing screen is displayed. Click [CF] or [SD]. Click the [DCIM] folder and select the folder containing the images. C 3 Y P O Select an image. To view another image, click the < > buttons or jump to other pages.
Viewing Images 4 Download images to the computer. Click a thumbnail. X The image is displayed at a larger size. To download the image to your computer, click < >. Click [Return] to return to the image viewing screen. Y P O Although actual RAW images and movies are not displayed here, they can be downloaded to the computer in the same way as JPEG images.
Remote Capture [Camera control] Set up the camera for Live View shooting beforehand. Note that remote capture of movies is not supported. For web browsers that do not support JavaScript, see page 63, “Remote Capture”. 1 Click [Camera control]. X The advanced capture screen is displayed.
Remote Capture [Camera control] ⑯ ⑱ 2 Set the lens focus mode switch to . 3 Display the Live View image. Click the release button (⑤). When you let go of the button, the camera autofocuses and the picture is taken. With One-Shot AF, the picture is not taken if focus is not achieved. Display the Live View image and focus manually as described in the next steps. Click the Live View shooting button (⑯). X The AF/MF switch (⑥) is set to , and the Live View image is displayed.
Remote Capture [Camera control] 5 Configure the shooting functions. 6 Take the picture. Click items such as quality to view and configure their settings. Complete the settings as needed. Click the release button (⑤). When you let go of the button, the picture is taken. X The captured image will be displayed. Captured images are stored on the camera’s memory card. To download images to your computer, see page 57, and use the [Viewer] function.
Remote Capture [Simple control] Set up the camera for Live View shooting beforehand. Note that remote capture of movies is not supported. For web browsers that do not support JavaScript, see page 63, “Remote Capture.” 1 Click [Simple control]. X The basic capture screen and the Live View image are displayed.
Remote Capture The following instructions are for remote capture with web browsers that do not support JavaScript. Set up the camera for Live View shooting beforehand. Note that remote capture of movies is not supported. Screen Release button 1 Click [Capture]. 2 Take the picture. X The capture screen is displayed. The Live View image is not displayed. Set the lens focus mode switch to . Adjust the focus on the camera. Click the release button. When you let go of the button, the picture is taken.
Using WFT Server in Linked Shooting Remote Capture in WFT Server can be used in combination with the transmitter’s “Linked Shooting” function (p.74). Additionally, you can view and download images recorded on the master or slave camera’s memory cards.
Using the Transmitter as a Media Server Y P O Images on a memory card in the camera can be viewed over a wireless or wired LAN on a television. This function requires a DLNA*-compatible television, digital photo frame, or C similar media player. (Subsequently, this equipment is collectively referred to as the media player.
Configuring Media Server Communication Settings These instructions are continued from Chapter 1. Press <0> and turn the <5> dial to select the set number, and then press <0>. Press <0> again. After the connection wizard closes, the display will return to the menu screen. X The lamp on the transmitter lights up green. The information you specified is stored on the camera. It is not stored on the transmitter. The media server network settings are now complete.
Displaying Captured Images on a Television Operate the media player controls to display images recorded on the camera’s memory card on a television. Note that RAW images and movies cannot be displayed. The following operations are performed on the media player. For details, refer to the instruction manual for the media player. 1 Display the media player setting screen on your television. Using the media player functions, display the EOS**> (media server) icon on the television.
C 68 Y P O
Linked Shooting Y P O With linked shooting, up to 10 slave cameras can be linked in a wireless network to the master camera on which you will release the shutter. Note that there will be a slight delay after you release the master camera C shutter until the slave camera shutters are released. Movie shooting is not supported.
Preparing Slave Cameras After setting up the slave cameras as described on this page, follow the steps on the next page for basic linked shooting. For instructions to view or download to your computer the images stored on cameras, see page 74. 1 Select [Communication settings]. 2 3 Select [Network settings]. 4 Select [LinkedShot]. 5 Set up the slave cameras. Select [Connection wizard]. C Y P O Select [Slave]. X The slave cameras are now ready, with the following screen displayed.
Basic Linked Shooting Shoot with the master camera linked to slave cameras as follows. 1 Set up the master camera. 2 Select [Auto connect]. 3 Set up the slave cameras. Configure the settings on the master camera following steps 1-3 on the preceding page, and then select [Master]. For [Manual connect] instructions, see page 75. Y P O 4 C On the slave cameras, select [OK]. Check the number of slave cameras. X On the master camera LCD monitor, the number of slave cameras detected is displayed.
Positioning the Slave Cameras Slave camera Slave camera Slave camera Slave camera Y P O Master camera C Position the slave cameras in clear view of the master camera, without objects between them. You can position master camera in an overall circumference of up to approximately 100 m / 328 ft.
Positioning the Slave Cameras Do not use multiple flash units. Although slight, there is a difference in the shutter release timing which may cause out-of-sync flash firing and inadequate exposure. Linked shooting is not possible when master and slave cameras are set to [Mirror lockup] [Enable] or [Enable:Mirror down w/ s]. During linked shooting, when you press the AE lock or depth-of-field preview button, the camera adjusts the focus and meters as if you had pressed the shutter button halfway.
Using the Transmitter with WFT Server Using WFT Server, you can shoot remotely with a master camera linked to slave cameras that will shoot at the same time. WFT Server can also be used to access master or slave cameras for the Live View display, and you can adjust the focus and configure remote capture settings as needed. Additionally, images on the camera’s memory cards can be viewed and downloaded.
Using the Transmitter with WFT Server Connect the Master and Slave Cameras 1 2 Set up the slave cameras. 3 Select [Manual connect]. 4 Select the connection mode. 5 Specify the channel. Set up the slave cameras as described on page 70. Set up the master camera. Complete settings on the master camera following steps 1–3 on page 70, and then select [Master]. C Y P O Select the wireless LAN ad hoc mode supported by the computer.
Using the Transmitter with WFT Server 6 Enter the encryption key. 7 Switch to setting up the slave cameras. 8 Check the number of slave cameras. Enter a 5-digit encryption (WEP) key and press the <7> button. The key entered here will be saved on the computer and used to access the master camera from the computer. X On the slave cameras, select [OK]. X On the master camera LCD monitor, the number of slave cameras detected is displayed. Y 9 OP C Establish the connection.
Using the Transmitter with WFT Server Check the Camera Settings Check the network settings on the master and slave cameras as follows. Note that without a good understanding of these settings, you cannot access the cameras from a computer. 1 On the master camera, select [Communication settings]. 2 Select [Network settings]. 3 Select [Set up]. Y P 4C O Select [Confirm settings]. X The settings are displayed.
Using the Transmitter with WFT Server 5 Check the settings. 6 Check the slave camera settings. Turn the <5> dial to display other screens. Write down the IP address and SSID. C 78 Check network settings on the slave cameras in the same way as you checked the master camera settings. Write down the IP address of all slave cameras. Each camera has a different address. The SSID will be the same as the master camera SSID.
Using the Transmitter with WFT Server Configure WFT Server Communication Settings Enter a login name and password for accessing WFT Server on cameras from a computer. Although you can specify different login names and passwords for each camera, it is also possible to use the same information for all cameras. 1 On the master camera, select [Communication settings]. 2 Select [Network settings]. 3 Select [Set up]. C Y P O 4 Select [WFT server settings]. 5 Select [WFT account].
Using the Transmitter with WFT Server 6 Select a user number. 7 Complete the [Login name] and [Password] settings. WFT Server can accept connections from up to three computers per camera. Select a user number to prevent conflicts when users at other computers are connected to the transmitter at the same time. After you select [Login name] and [Password], the following input screen is displayed. For instructions on input screen operations, see “Virtual Keyboard Operation” (p.29).
Using the Transmitter with WFT Server Access the Cameras from the Computer To access the cameras from the computer, use the computer’s standard search function to detect wireless LAN terminals. For details, refer to the computer instruction manual. 1 From the computer, find cameras on the network. 2 Connect to a camera. Use built-in searching on the computer to detect wireless LAN terminals. Select a device with the same ID as the SSID you wrote down in steps 5 and 6 on page 78.
Using the Transmitter with WFT Server 4 Select the language. Select a language on the bottom of the screen. Web browsers that support JavaScript will display the screen on the left. A message is displayed when JavaScript is not supported. Selecting not to use JavaScript will display the screen on the right, with limited functions. Y P O View Images on the Camera C See “Viewing Images” on page 57. Images on camera memory cards can be viewed and downloaded.
Managing Settings Information C Y P O 83
Checking Settings Check the network settings as follows. 1 In [Network settings], select [Set up]. 2 Select [Confirm settings]. X The settings are displayed.
Changing Settings Settings originally completed using the connection wizard can be changed as follows. You can also change IP security settings (IPsec) not completed using the connection wizard, as well as other settings, such as the setting that determines what happens if an image of the same file name as an existing file is sent to the FTP server (p.86). 1 In [Network settings], select [Set up]. 2 Select [LAN settings]. 3 Select the settings number. 4 Select [Change].
Changing Settings IP Security (IPsec) Configured in [TCP/IP] [Security]. IPsec is a set of standards for encrypted communication over the Internet. It provides effective security for both wireless and wired LANs. To use this function, you must enable IPsec in the network settings of your computer. When IPsec is employed, only transport mode is supported, and 3DES or AES encryption and SHA1 authentication are used.
Saving and Loading Settings Network settings can be saved on a memory card for use with other cameras. Saving Settings 1 In [Network settings], select [Set up]. 2 Select [LAN settings]. 3 Select the settings number. Y P O Here, select the settings number under which you saved LAN settings. C 4 Select [Change]. 5 Select [Save settings].
Saving and Loading Settings 6 Select [Save]. X The settings are now saved as a file on the memory card. The settings are saved as a file (WFTNPF**.NIF) in the area of the memory card shown when the card is opened (in the root directory). The file name is determined automatically by the camera: WFTNPF, followed by a number (01 to 99) and the extension NIF. You can rename the file as desired by selecting [Change file name]. Loading Settings Load settings files stored on a memory card as follows.
Synchronizing the Camera Time Y P O Set the master camera time on up to 10 slave cameras, as needed. Synchronization can be done over a wireless or wired connection. Note that even after synchronization, there will be a slight margin of error between master and slave camera time of ±0.05 seconds, at most.
Preparing for Time Synchronization Wireless LAN Set up multiple cameras with transmitters attached. Slave camera Master camera Wired LAN Slave camera Y P O Use a LAN cable to connect cameras with transmitters attached. When there are multiple slave cameras, connect them to a hub with LAN cables, and connect the hub to the master camera with a LAN cable.
Synchronizing the Time Steps 1–5 are the same on master and slave cameras. 1 In the menu, select [Communication settings]. 2 Select [Network settings]. 3 Set [Communication mode] to [Disconnect]. Y P O Once [Communication mode] is set to [Disconnect], you can select [Sync time between cameras]. C 4 Select [Sync time between cameras]. 5 Select [LAN Type]. X Select [OK] on the next screen displayed, shown below. After selecting [Wireless] or [Wired], select [OK].
Synchronizing the Time 6 Set up the master camera. 7 Set up the slave cameras. After configuring the master camera settings following steps 1–5 on the preceding page, select [Master]. X When the next screen is displayed, the master camera is ready. Go to step 7 to set up the slave cameras. After configuring the slave camera settings following steps 1–5 on the preceding page, select [Slave]. X Select [OK] on the next screen displayed, shown below.
Using Bluetooth GPS Devices Y P O Information including the latitude, longitude, elevation, and date and time can be obtained from commercially-available GPS devices connected via Bluetooth and added to images. The additional information can be checked on the camera as well as by using commercially-available GPS-compatible mapping software. C For a list of specific GPS devices supported, contact the Canon Service Center.
Connecting GPS Devices via Bluetooth 1 In the menu, select [Communication settings]. 2 Select [Bluetooth device connection]. 3 Once [Communication func] is set to [Enable], you can select [Bluetooth device connection]. X Press <0> when the next screen shown below is displayed. Select the GPS device. C 94 Y P O Nearby active Bluetooth® devices are listed. Turn the <5> dial to select the GPS device, and then press <0>. Select [OK] and press <0>.
Connecting GPS Devices via Bluetooth 4 When the confirmation message is displayed, select [OK]. The GPS connection status changes to [Connected]. Pressing <0> under these conditions will enable you to disconnect the GPS device. While the Bluetooth connection is active, is displayed on the transmitter’s LCD panel and is displayed on the camera’s LCD panel. 5 6 Confirm operation of the GPS device. Make sure the GPS device has determined the current location. Take the picture.
Connecting GPS Devices via Bluetooth Canceling the Bluetooth Connection The Bluetooth connection with the GPS device will not be terminated if you simply turn off the camera. To cancel the connection, follow these steps. 1 In the menu, select [Communication settings]. 2 Select [Bluetooth device connection]. 3 Select [OK]. X Press <0> when the next screen shown below is displayed. Y P O X The Bluetooth connection is canceled. C Select [OK] to return to the [Bluetooth device connection] screen.
Troubleshooting C Y P O Transfer speed in ad hoc mode may become extremely slow when the transmitter is used with certain types of computer. For more information, contact your dealer or nearest Canon Service Center.
Handling Error Messages If transmitter errors are displayed on the camera LCD monitor, refer to the examples of corrective actions in this section to eliminate the cause of the error. When an error has occurred, the lamp on the transmitter blinks and the error number is shown on the LCD panel. The error details can also be checked in the menu, [WFT settings] [Error description]. Click the error number in the following chart to jump to the corresponding page. 11 (p.99) 12 (p.99) 21 (p.99) 22 (p.
Handling Error Messages 11: Connection target not found Is the pairing software running? X Start the pairing software and follow the instructions to re-establish the connection (p.48). Are the transmitter and wireless LAN terminal configured with the same encryption key for authentication? X This error occurs if the encryption keys do not match when the authentication method for encryption is [Open system]. The setting is case-sensitive, so check upper- and lower-case characters.
Handling Error Messages 22: No response from DNS server What to check on the transmitter Is the transmitter’s DNS address setting set to [Auto assign] or [Manual setting]? X If you are not using a DNS server, set the transmitter’s DNS address setting to [Disable] (p.27). On the transmitter, does the DNS server’s IP address setting match the server’s actual address? X Configure the IP address on the transmitter to match the actual DNS server address (p.27, 112).
Handling Error Messages 24: No response from proxy server What to check on the transmitter The transmitter’s proxy server setting is [Enable]. Does the error occur under this setting? X If you are not using a proxy server, set the transmitter’s proxy server setting to [Disable] (p.32). Do the transmitter’s [Address setting] and [Port No.] settings match those of the proxy server? X Configure the transmitter’s proxy server address and port number to match those of the proxy server (p.32).
Handling Error Messages 25: Another terminal has set the same IP address Is another device on the transmitter network using the same IP address as the transmitter? X This error occurs if the transmitter is connected to a network where another device subsequently connects with the same IP address. Change the transmitter’s IP address to avoid using the same address as another device on the network. Otherwise, change the IP address of the device that has a redundant address.
Handling Error Messages 41: Cannot connect to FTP server What to check on the transmitter On the transmitter, does the FTP server’s IP address setting match the server’s actual address? X Configure the IP address on the transmitter to match the actual FTP server address (p.32). Are the transmitter and wireless LAN terminal configured with the same encryption key for authentication? X This error occurs if the encryption keys do not match when the authentication method for encryption is [Open system].
Handling Error Messages Are you connecting to the FTP server via a broadband router? X Some broadband routers use a firewall to restrict access to the FTP server. Change the firewall settings to allow access to the FTP server. X You may be able to access the FTP server by setting [Passive mode] to [Enable] on the transmitter (p.86).
Handling Error Messages 45: Cannot login to FTP server. Error code received from server. What to check on the transmitter On the transmitter, is the [Login name] entered correctly? X Check the login name for accessing the FTP server. The setting is case-sensitive, so check upper- and lower-case characters. Make sure the correct login name is entered on the transmitter (p.33).
Handling Error Messages 47: Image file transfer completion not confirmed by FTP server This error occurs if, for some reason, the transmitter fails to receive confirmation from the FTP server that image file transfer is complete. X Turn the FTP server and camera off and on and send the images again. 51: Connection to Bluetooth device lost Is the Bluetooth unit too far from the GPS device? X Bring the GPS device closer to the Bluetooth unit.
Handling Error Messages 61: Selected SSID wireless LAN network not found Are any obstacles blocking the line of sight between the transmitter and the antenna of the wireless LAN terminal? X Move the antenna to a position clearly visible from the point of view of the transmitter (p.111). What to check on the transmitter On the transmitter, does the SSID setting match that of the wireless LAN terminal? X Check the SSID on the wireless LAN terminal, and configure the same SSID on the transmitter (p.23).
Handling Error Messages 63: Wireless LAN authentication failed Are the transmitter and wireless LAN terminal configured for the same authentication method? X The transmitter supports these authentication methods: [Open system], [Shared key], [WPA-PSK], and [WPA2-PSK] (p.23). X When using an AirPort for communication in infrastructure mode, [Open system] is not supported. Configure a [Shared key] on the transmitter (p.23).
Handling Error Messages 66: Incorrect wireless LAN encryption key Are the transmitter and wireless LAN terminal configured with the same encryption key for authentication? X The setting is case-sensitive, so check upper- and lower-case characters. Make sure the correct encryption key for authentication is entered on the transmitter and wireless LAN terminal (p.24). Note that if the authentication method is [Open system], an Error 41 (“Cannot connect to FTP server”) is displayed.
Handling Error Messages 71: Cannot connect to slave camera Are you following the correct procedure to establish the connection with slave cameras? X Operate slave cameras by following the correct instructions (p.70, 71). Are the slave cameras too far from the master camera? X Bring the slave cameras closer to the master camera.
Wireless LAN Notes When using the transmitter with a wireless LAN, try the following corrective actions if the transmission rate drops, the connection is lost, or other problems occur. Wireless LAN Terminal Installation and Antenna Position When using the transmitter indoors, install the wireless LAN terminal in the room where you are shooting. Install the wireless LAN terminal higher than the transmitter.
Checking Network Settings Windows Click the Windows [Start] button [All Programs] [Accessories] [Command Prompt]. Type ipconfig/all and press the key. The IP address assigned to the computer is displayed, as well as the subnet mask, gateway, and DNS server information. To avoid using the same IP address for the computer and other devices on the network when configuring the IP address assigned to the camera (page 27), change the rightmost numbers here.
Reference C Y P O 113
Creating and Registering Captions Follow these steps to create captions and register them on the camera, as described in “Adding a Caption Before Transfer” (p.38). When creating and registering captions, use a computer on which EOS Utility is installed. See “Remote Capture Using EOS Utility” from page 47 to start up EOS Utility and enable its use over a wired or wireless LAN. For instructions on starting EOS Utility, refer to the Software Instruction Manual (PDF) provided with the camera.
Using a Bracket (Sold Separately) Attaching the optional Accessory Bracket AB-E1 enables you to use the transmitter and a battery grip at the same time. Attach the camera and transmitter to the bracket as shown.
Specifications Type Type: Wired and wireless (IEEE 802.11a/b/g/n) IPsec-compatible image transfer accessory with Bluetooth connectivity for GPS devices Wireless LAN Standards compliance: IEEE 802.11a IEEE 802.11b IEEE 802.11g IEEE 802.11n Transmission method: DS-SS modulation (IEEE 802.11b) OFDM modulation (IEEE 802.11a/g/n) Transmission range: Approx. 150 m / 492 ft.
Specifications Network Functions FTP transfer: EOS Utility: WFT Server: Media Server: Linked shooting: Wireless time synchronization: Automatic transfer Image selection and transfer Transfer using SET button Transfer with captions EOS Utility remote control functions over wireless and wired LAN Camera control, simple control, basic shooting, image viewing, and downloading DLNA compatible Shooting with up to 10 slave cameras linked to a master camera Transmission range: Approx. 100 m / 328 ft.
Specifications USA and Canada only: The Lithium ion/polymer battery is recyclable. Please call 1-800-8BATTERY for information on how to recycle this battery. When connecting to and using a household power outlet, use only AC Adapter Kit ACK-E6 (rated input: 100-240 V AC 50/60 Hz, rated output: 8.0 V DC). Using anything else can cause fire, overheating, or electrical shock.
MEMO C Y P O 119
MEMO C 120 Y P O
MEMO C Y P O 121
MEMO C 122 Y P O
MEMO C Y P O 123
Index A GPS device ............................................... 16 AC adapter ................................................ 13 Account ..................................................... 54 Ad hoc ....................................................... 23 Authentication...................................... 23, 86 Auto power off ........................................... 19 B Batch transfer ................................ 40, 42, 44 Battery ......................................................
Index PIN code connection mode ....................... 26 PIN mode .................................................. 26 Port number............................................... 32 Power lamp ................................................. 9 Power switch ......................................... 9, 14 Protect settings.......................................... 86 Proxy ......................................................... 32 Pushbutton connection mode.................... 25 R WFT Server...........
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. One Canon Plaza, Lake Success, NY 11042-1198, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC. MONTREAL BRANCH 5990, Côte-de-Liesse, Montréal Québec H4T 1V7, Canada CANON CANADA INC. CALGARY OFFICE 2828, 16th Street, N.E.