PUB.
Important Usage Instructions WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. COPYRIGHT WARNING: Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be contrary to copyright laws.
European Union (and EEA) only. These symbols indicate that this product is not to be disposed of with your household waste, according to the WEEE Directive (2002/96/EC), the Battery Directive (2006/66/EC) and/or your national laws implementing those Directives. This product should be handed over to a designated collection point, e.g.
Highlights of the XF305/XF300 The Canon XF305/XF300 HD Camcorder has been designed to fulfill the needs demanded by industry professionals. The following are just some of the many features that will help turn your creative vision into reality. HD Recording 3CMOS system and DIGIC DV III image processor The camcorder is equipped with three 1/3-type CMOS sensors that each capture video at an effective pixel count of approximately 2.07 megapixels (1920x1080).
Custom picture settings With custom picture settings (0 113), you can enjoy unparalleled image control to deliver the “look” you want by adjusting parameters, such as gamma and sharpness. The custom picture settings can be recorded onto an SD card, which allows multiple XF305/XF300 camcorders to use the same settings, or embedded in the recording itself.
Table of Contents 1. Introduction 9 3.
Onscreen Markers and Zebra Patterns 79 Displaying Onscreen Markers 79 Displaying Zebra Patterns 80 Setting the Time Code 82 Selecting the Running Mode 82 Putting the Time Code Display on Hold 84 Setting the User Bit 85 b Synchronizing with an External Device 86 Connecting an External Device 86 Using a Reference Video Signal (Genlock Synchronization) 87 Using a Time Code Signal 87 Time Code Signal Output 88 Recording Audio 89 Using the Built-in Microphone 89 Using an External Microphone or Line Input 90 Adju
6. External Connections 143 7.
1 Introduction About this Manual Introduction 1 Introduction About this Manual Thank you for purchasing the Canon XF305/XF300. Please read this manual carefully before you use the camcorder and retain it for future reference. Should the camcorder fail to operate correctly, refer to Troubleshooting (0 183). Conventions Used in this Manual Y P O • IMPORTANT: Precautions related to the camcorder’s operation. • NOTES: Additional topics that complement the basic operating procedures.
About this Manual Introduction 1 When a function requires the use of the menu, the quick reference shows the submenus and, when applicable, the default setting for the menu item. The example illustration indicates that you can find the function by selecting the [l Camera Setup] menu and then the [Image Stabilizer] menu item.
Supplied Accessories Introduction 1 Supplied Accessories The following accessories are supplied with the camcorder. * CA-930 Compact Power Adapter (incl. power cord) BP-955 Battery Pack (incl. terminal cover) DTC-1500 Component Video Cable Lens Hood Viewfinder Cap Lens Cap SS-1200 Shoulder Strap Canon XF Utilities Disc* DC-930 DC Cable Y P O Eye Cup C WL-D6000 Wireless Controller (incl.
Introduction 1 Names of Parts Names of Parts 1 2 Operation panel 34 (0 18) 5 6 20 1 C 19 18 17 16 15 14 ZOOM SPEED switch for the handle zoom rocker (0 77) 2 Side panel (0 48) 3 e switches (0 93) 4 SLOT SELECT (CF card slot selection) button (0 40) 5 CFj (CF card slot A) and CFl (CF card slot B) access indicators (0 38) 6 e dials for CH1 and CH2 (0 93) 7 MENU button (0 28) 8 STATUS button (0 177) 9 SELECT dial (0 28) 10 FULL AUTO switch (0 45) 12 Y P O Operation panel 7 8 9 13 12 11 10
Names of Parts Introduction Terminals (0 19) 1 2 3 C 4 5 6 Y P O 10 1 2 3 4 5 6 7 8 9 10 1 9 8 7 Speaker (0 132) SD card slot cover SD card access indicator (0 39) SD card slot (0 39) PUSH button (0 53) Focus mode ring (0 53) Lens hood lock screw (0 30) XLR terminals (CH1 and CH2) (0 90) AUDIO IN switches for CH1 and CH2 (0 89, 91) Grip belt (0 34) 13
Introduction 1 Names of Parts 10 9 8 1 7 2 6 5 4 1 2 3 4 5 6 7 8 9 10 14 C Y P O Remote sensor (0 36) MIRROR button (0 32) START/STOP button (0 44) RESET button (0 184) XLR terminal switches for CH1 and CH2 (0 91) Instant AF sensor (0 57) Front tally lamp (0 44) Microphone cable clamp (0 90) Microphone holder (0 90) Microphone lock screw (0 90) 3
Names of Parts Introduction 1 2 1 3 4 11 5 6 10 13 9 12 8 C 7 1 2 3 4 5 6 7 8 9 10 11 12 13 Y P O Terminals (0 19) LCD screen (0 33) Viewfinder unit Viewfinder (0 31, 33) Dioptric adjustment lever (0 31) RELEASE (viewfinder release) switch (0 193) CF card slot cover switches for CF card slots A (top) and B (bottom) (0 37) Battery compartment cover (0 22) BATT.
Names of Parts Introduction 1 1 2 3 4 5 6 7 12 Y P O Operation panel 11 1 C (0 18) 7 10 9 8 Accessory shoe For attaching accessories such as the optional VL-10Li II Battery Video Light. 2 Grip zoom rocker (0 76) 3 MAGN. (magnification) button (0 56)/Assignable button 6 (0 111) 4 START/STOP button (0 44) 5 U (review recording) button (0 101)/Assignable button 5 (0 111) 6 Handle socket for 0.
Names of Parts Introduction 1 1 2 C 1 2 3 4 Y P O 4 3 Attachment sockets for the optional TA-100 Tripod Adapter (0 36) Attachment screws for the tripod base (0 36) Tripod socket (0 36) Tripod base for tripods with 0.
Introduction 1 Names of Parts 1 2 3 Operation panel 1 2 4 3 4 9 5 6 8 7 Operation panel 14 10 13 11 12 Operation panel 15 27 26 16 17 18 25 19 20 21 24 22 23 18 C 5 6 7 8 9 10 11 12 13 14 15 PUSH AF button (0 58) FOCUS switch (0 54, 57) IS (image stabilizer) button (0 60)/ Assignable button 1 (0 111) PEAKING button (0 56) / Assignable button 2 (0 111) ZEBRA button (0 79)/ Assignable button 3 (0 111) WFM (waveform monitor) button (0 97)/ Assignable button 4 (0 111) IRIS switc
Names of Parts Introduction Terminals 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 Terminals C 1 DC IN terminal (0 24) b HD/SD SDI terminal (0 146) b GENLOCK terminal (0 87) b TIME CODE terminal (0 88) VIDEO 2 terminal (0 147) W (headphone) terminal (0 94) REMOTE terminal HD/SD COMPONENT OUT terminal (0 146) HDMI OUT terminal (0 146) USB terminal (0 150) AV terminal (0 147) Y P O 6 11 7 10 9 8 19
Introduction 1 Names of Parts WL-D6000 Wireless Controller 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 20 14 13 12 11 10 2 9 8 4 7 5 3 C Y P O 6 START/STOP button (0 44) ZOOM buttons (0 78) F/O/E/A buttons MENU button (0 28) J/I (fast playback/reverse playback) buttons (0 131) Z/Y (frame forward/reverse) buttons (0 131) B (stop) button (0 129) D (play/pause) button (0 129) INDEX button (0 128) SET button (0 28) CANCEL button (0 28) SHOT1 (shot mark 1) button (0 100) PHOTO button (0 159) Record enabl
2 Preparations Preparing the Power Supply Preparations You can power the camcorder using a battery pack or directly using the compact power adapter. If you connect the compact power adapter to the camcorder while a battery pack is attached, the camcorder will draw power from the power outlet. Charge battery packs before use. For approximate charging times and recording/playback times with a fully charged battery pack, refer to Charging Times (0 196) and Recording and Playback Times (0 196).
Preparations 2 Preparing the Power Supply 6 Unplug the power cord from the power outlet and disconnect it from the compact power adapter. NOTES • To charge the battery pack, disconnect the DC cable from the compact power adapter. • The supplied BP-955 and optional BP-975 Battery Packs are not compatible with previous Canon camcorder models. Attaching the Battery Pack 1 Hold down the button on the d switch and move it to OFF ( ). 2 Slide the BATT.
Preparing the Power Supply Preparations 2 0-25% 26-50% 51-75% 76-100% When the camcorder is off and an Intelligent System-compatible battery pack is attached, press the BATT. INFO (battery information) button to display the remaining battery time and available recording time (displays for 5 seconds). Depending on the battery life, the battery information may not be displayed. IMPORTANT • Do not connect to the compact power adapter any product that is not expressly recommended for use with this camcorder.
Preparations 2 Preparing the Power Supply Using a Household Power Outlet When Using the Supplied CA-930 Compact Power Adapter and DC-930 DC Cable: 1 Hold down the button on the d switch and move it to OFF ( ). 2 Connect the DC cable to the DC IN terminal on the camcorder ( ). 3 Connect the power cord to the compact power adapter and plug it into a power outlet ( ). 4 Connect the DC cable to the compact power adapter ( ).
Preparing the Power Supply Preparations 2 Turning the Camcorder On and Off The camcorder has two operating modes: CAMERA ( ) mode for making recordings and MEDIA ( ) mode for playing back recordings. Select the operating mode using the d switch. To turn on the camcorder Hold down the button on the d switch and move it to CAMERA for mode or MEDIA for mode. CAMERA mode MEDIA mode Y P O To turn off the camcorder Hold down the button on the d switch and move it to OFF.
Preparations 2 Date, Time and Language Settings Setting the Date and Time Date, Time and Language Settings You will need to set the date and time of the camcorder before you can start using it. When the camcorder’s clock is not set, the [Date/Time] screen will appear automatically with the day selected. Operating modes: 1 Push the joystick up/down or turn the SELECT dial to change the day then move (A) to the month. Y P O 2 Change the rest of the fields in the same way.
Date, Time and Language Settings Preparations 2 4 Push the joystick up/down or turn the SELECT dial to change the time zone. 5 Press SET to set the time zone and then press the MENU button to close the menu. Displaying the Date and Time while Recording You can display the date and time in the lower left of the screen. [M LCD/VF Setup] [Custom Display] Operating modes: [Date/Time] 1 Press the MENU button. 2 Push the joystick up/down or turn the SELECT dial to select [M LCD/VF Setup].
Preparations 2 Using the Menus In mode, many of the camcorder’s functions can be adjusted from the menu for general settings, which opens after pressing the MENU button. In mode, press the MENU button to open the menu for general settings or SET to open the clip menu for clip operations. For details about the available menu options and settings, refer to Menu Options (0 167).
Using the Menus Preparations 2 4 Push the joystick up/down or turn the SELECT dial to select the desired menu item. • If a submenu contains many menu items, a scroll bar will appear on the right side of the submenu indicating that you must scroll up or down to see other menu items. • A A mark next to a menu item indicates another submenu. Repeat steps 3 and 4. 5 Push the joystick right or press SET. • The orange selection frame will appear on a setting option.
2 Preparations Preparing the Camcorder This section outlines the basic preparations for the camcorder such as attaching the lens hood, attaching/removing the eyecup, and adjusting the viewfinder and LCD screen. Preparing the Camcorder Attaching the Lens Hood Attach the lens hood to protect the lens and reduce the amount of stray light that may hit the lens.
Preparing the Camcorder Preparations 2 Detaching the Eye Cup Detach the eye cup as shown in the illustration. Dioptric Adjustment Y P O Turn on the camcorder and adjust the dioptric adjustment lever. C Attaching the Viewfinder Cap Pointing the viewfinder lens at the sun or other strong light sources may cause damage to internal components. When you are not using the viewfinder, make sure to attach the viewfinder cap to the viewfinder. This will also protect the viewfinder from scratches and dirt.
Preparations 2 Preparing the Camcorder Using the LCD Panel You can slide out the LCD panel to the left or right based on your preference and shooting situation. 1 Slide out the LCD panel. • To slide out the LCD panel to the left, push on the right side of the LCD panel. To slide out the LCD panel to the right, push on the left side. 2 Extend the LCD panel out until it is perpendicular to the handle ( ). 3 Rotate the LCD panel and adjust it to the desired position ( ).
Preparing the Camcorder Preparations 2 Adjusting the Viewfinder/LCD Screen You can adjust the brightness, contrast, color, sharpness, and backlight of the viewfinder and LCD screen independently of each other. These adjustments will not affect your recordings. [M LCD/VF Setup] [LCD Setup] [VF Setup] Operating modes: 1 Open the setup menu for the viewfinder or LCD screen.
2 Preparations Preparing the Camcorder Adjusting the Grip Belt Adjust the grip belt so that you can reach the grip zoom rocker with your index and middle fingers, and the START/STOP button with your thumb. IMPORTANT • Be careful not to drop the camcorder when adjusting the grip belt. Attaching a Shoulder Strap Pass the ends through the strap mount and adjust the length of the strap. Y P O IMPORTANT • Be careful not to drop the camcorder when attaching or adjusting the shoulder strap.
Preparing the Camcorder Preparations 2 Removing and Attaching the Terminal Covers Remove the covers for the following terminals in order to access them. • • • • HD/SD SDI terminal* GENLOCK and TIME CODE terminals* VIDEO 2 terminal W (headphone) and REMOTE terminals • HD/SD COMPONENT OUT terminal • AV terminal • USB and HDMI OUT terminals * b only. Removing the Terminal Covers 1 Open the terminal cover and pull it out. 2 Grasp the strip connecting the terminal cover to the camcorder and pull.
2 Preparations Preparing the Camcorder NOTES • You can also activate the wireless controller by setting an assignable button to [Wireless Controller] (0 111). Using the Wireless Controller to Operate the Camcorder When using the wireless controller, point it at the camcorder’s remote sensor. When the wireless controller's buttons are operated, the camcorder's tally lamps will illuminate.
Preparing Recording Media Preparations The camcorder records clips to CompactFlash (CF) cards and photos* to SD and SDHC memory cards. The camcorder is equipped with two CF card slots. Initialize recording media (0 39) when you use them with this camcorder for the first time. 2 Preparing Recording Media * The camcorder can record custom picture settings and camera settings on to an SD card.
Preparations 2 Preparing Recording Media Checking the Status of the CF Card Slots You can check the status of the CF card slots immediately by looking at the CFj/CFl access indicator. Refer to the following table. Access indicator color CF card slot status Red Accessing CF card. Green Recording/playback is possible and the CF card slot is selected for recording/playback. Indicator off A CF card is not inserted, the CF card slot is not currently selected, or the CF card is not being accessed.
Preparing Recording Media Preparations 2 Inserting and Removing an SD Card 1 Turn off the camcorder ( ). 2 Open the SD card slot cover. 3 Insert the SD card straight, with the label facing the grip belt, all the way into the SD card slot until it clicks ( ). 4 Close the SD card slot cover ( ). • Do not force the cover closed if the SD card is not correctly inserted. IMPORTANT • Observe the following precautions while the SD card access indicator is flashing.
2 Preparations Preparing Recording Media To initialize a CF card 3 Select [OK] and then press SET. 4 When the confirmation message appears, press SET. • The CF card is initialized and all the data it contains is erased. To initialize an SD card 3 Select [Complete] (complete initialization) or [Quick] (quick initialization) and then press SET. 4 Select [OK] and then press SET. • If you are using the [Complete] initialization option, press SET twice to cancel the operation while it is in progress.
Preparing Recording Media Preparations 2 NOTES • If both CF card slots contain a CF card and you open the cover of the selected slot, the camcorder will automatically switch to the other slot. • You cannot use the SLOT SELECT button to switch between CF card slots while recording. • When the bit rate is set to 50 Mbps (0 51) during slow motion recording, relay recording is not available.
2 Preparations Preparing Recording Media Checking the Available Recording Time When the camcorder is in mode, the screen indicates which CF card slot is in use and the available recording time (in minutes*) that remains on each CF card. When the camcorder is in mode, the side panel indicates the available recording time. On the [Media] status screen (0 179), you can check the available recording time, total space and used space of each recording media, and the available number of photos.
3 Recording Recording Video Recording This section explains the recording basics. Before you begin recording, make a test recording first to check if the camcorder operates correctly. Record for approximately 6 minutes at 50 Mbps (0 51). Should the camcorder fail to operate correctly, refer to Troubleshooting (0 183). For details on recording audio, refer to Recording Audio (0 89).
3 Recording Recording Video Recording 1 Hold down the button on the d switch and move it to CAMERA (0 25). • The camcorder turns on in mode and enters record pause mode. • The access indicator for the CF card slot selected for recording illuminates in red and then changes to green. Y P O 2 Press the START/STOP button to begin recording. • Recording starts. The front and rear tally lamps illuminate and the recording indicator [NREC] appears on the screen.
Recording Video Recording 3 • You can use the [J Other Functions] [Rec Review] setting (0 101) to review the last clip recorded. • If you set an assignable button to [Add e Mark] or [Add Z Mark] (0 111), you can press the button to add an e mark or Z mark to the last clip recorded. • You can use the [J Other Functions] [Clips] [Delete Last Clip] setting (0 174) to delete the last clip recorded. Alternatively, you can set an assignable button to [Delete Last Clip].
3 Recording Recording Video Onscreen Displays Refer to this section for an explanation of the various screen displays that appear in mode. You can use the custom display function (0 125) to display or hide most of the screen displays. Such screen displays are denoted with an asterisk (*).
Recording Video 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Remaining battery time* (0 49) Double slot recording (0 41) Recording operation* (0 49) Character recording* (0 124) Time code* (0 82) Interval counter* (0 102) SD card status* Bit rate/Resolution* (0 51) Frame rate* (0 51) b SDI recording command (0 175) Output displays* (0 147) Wireless controller* (0 35) Object distance* (0 54) Digital tele-converter* (0 168) Peaking* (0 56) User memo* (0 95) User bit* (0 85) Audio output channel* (0 149)
3 Recording Recording Video Side Panel Displays You can check the following information on the side panel even when the LCD panel is retracted. CF card status/ available recording time Time code setting Remaining battery time Time code Audio level meter Y P O NOTES • While the camcorder is in mode, the time code and time code setting will not be displayed. • [EXT-LOCK] appears only on the XF305.
Recording Video Recording 3 1 Remaining battery time • The icon shows a rough estimate of the remaining charge as a percentage of the full charge of the battery pack. The remaining recording/playback time of the battery pack is displayed, in minutes, next to the icon. • P Q R S U (in red). When U is displayed, replace the battery pack with a fully charged one.
3 Recording Recording Video Power Save Mode Activate the power save mode to turn off the screen and reduce battery consumption. At the press of a button, the camcorder will immediately return to record pause mode. 1 Hold the POWER SAVE button pressed down for at least 2 seconds. • The screen will turn off and the camcorder will switch to power save mode. • During power save mode, the tally lamps will flash twice approximately every 3 seconds.
Video Configuration: Bit Rate, Resolution and Frame Rate Before you record, select the bit rate, resolution (frame size) and frame rate that best match your creative needs. Recording Video Configuration: Bit Rate, Resolution and Frame Rate Operating modes: [J Other Functions] [Bit Rate/Resolution] 1 Open the [Bit Rate/Resolution] submenu to set the bit rate and resolution. [J Other Functions] 3 [50 Mbps 1920x1080] [Bit Rate/Resolution] 2 Select the desired option and then press SET.
3 Recording Video Configuration: Bit Rate, Resolution and Frame Rate NOTES • For details on the signal output from each terminal, refer to Video Output Configuration (0 143).
Adjusting the Focus Recording This camcorder features 4 methods for adjusting the focus. When you use full manual focus or manual focus, you can use the peaking and magnification functions to help you focus more accurately. 3 Adjusting the Focus Full manual focus (FULL MF): Use the focus ring to adjust the focus. The focus ring is non-perpetual (the ring has physical stops) and you can use the ring’s distance indicator. You can focus from 1 m to f throughout the entire zoom range.
3 Recording Adjusting the Focus 3 Turn the focus ring to adjust the focus. • When you focus at full telephoto, the image will be in focus throughout the entire zoom range. NOTES • Using the subject distance display on the screen: - When the camcorder switches out of autofocus mode or when you adjust the focus with the focus ring, the approximate subject distance is displayed on the screen for approximately 3 seconds.
Adjusting the Focus Recording 3 2 Press the PUSH button (unlock focus mode ring button) on the focus mode ring and turn the ring toward AF/MF. 3 Turn the focus ring to adjust the focus. NOTES • When using full manual focus mode: - If you turn the focus ring too quickly, the camcorder may not be able to focus immediately. In such case, the camcorder will focus on the subject after you finish turning the focus ring.
Recording 3 Adjusting the Focus Peaking [M LCD/VF Setup] [Select] (under [Peaking]) [Peaking 1] The camcorder offers two peaking levels. Select the level before activating peaking. 1 Open the [Select] submenu (under [Peaking]) to select the peaking level. [M LCD/VF Setup] [Select] (under [Peaking]) 2 Select the desired level and then press SET. 3 Press the PEAKING button. • The peaking icon (a or b) appears and the outlines in the image will be emphasized. • Press the button again to turn off peaking.
Adjusting the Focus Recording 3 Autofocus Mode The camcorder uses the TTL autofocus system and continuously adjusts the focus on the subject in the center of the screen. The focusing range is 2 cm (at full wide-angle, measured from the front of the lens barrel) to f. During autofocus mode, you can turn the focus ring to focus manually. When you stop turning the focus ring, the camcorder returns to autofocus mode.
Recording 3 Adjusting the Focus Push AF During manual focus mode or Normal AF mode, press the PUSH AF button and hold it pressed down. • The autofocus (Instant AF mode) is activated as long as you hold the PUSH AF button pressed down. You can also use the PUSH AF button on the optional ZR-2000 Zoom Remote Controller. NOTES • When recording in bright surroundings, the camcorder closes down the aperture.
Adjusting the Focus Recording 3 • To change the main subject when there is more than one person, press the assignable button set to [Select Face]. NOTES • The camcorder may mistakenly detect the faces of non-human subjects. In such case, turn face detection off. • In certain cases, faces may not be detected correctly. Typical examples include: - Faces extremely small, large, dark or bright in relation to the overall picture. - Faces that are turned to the side, at a diagonal or partially hidden.
Recording 3 Image Stabilizer [l Camera Setup] [Image Stabilizer] [Standard] Image Stabilizer Use the image stabilizer to compensate for camcorder shake in order to achieve steadier shots. There are 3 methods of image stabilization; select the method that best suits your needs. Operating modes: 1 Open the [Image Stabilizer] submenu. [l Camera Setup] [Image Stabilizer] 2 Select the desired option and then press SET. • The icon of the selected mode appears on the bottom of the screen.
Gain Recording The gain control adjusts the level of the video signal generated depending on the lighting and shooting conditions. You can select automatic or manual gain control. 3 Gain Operating modes: Automatic Gain Control (AGC) Automatically adjusts the gain based on the subject’s brightness. Set the AGC switch to ON. • The A icon appears next to the gain value on the screen. • When you set the camcorder to full auto mode (0 45), automatic gain control will be activated.
Recording 3 Gain Manual Gain Control Set the AGC switch to OFF to set the gain manually. You can select one of 3 preset gain levels (L: low, M: middle, H: high) to which you can independently assign gain values. You can also fine-tune the gain in 0.5 dB increments. Assigning Gain Values to the GAIN Switch Positions [l Camera Setup] [Gain] You can assign separate gain values to the L, M and H positions of the GAIN switch. 1 Open the [Gain] submenu. [l Camera Setup] [Gain] [L 0.0 dB] [M 6.0 dB] [H 12.
Gain Recording 3 Exposure Bar Exposure bar When the gain and aperture are set to manual and the shutter speed is not set to auto, the exposure bar will appear on the screen. The exposure bar indicates the approximate exposure adjustment within a range of +/- 2 EV. Beyond this range, the indicator will flash. NOTES • When you select high gain levels, the picture may flicker slightly. The 33.
Recording 3 Shutter Speed Set the shutter speed based on the recording conditions. For example, you may want to set slower shutter speeds in darker environments. The camcorder offers the following 6 modes. Shutter Speed Operating modes: OFF: The camcorder uses a standard shutter speed based on the frame rate. Auto: The camcorder automatically adjusts the shutter speed based on the picture’s brightness. This mode is not available during slow & fast motion recording mode.
Shutter Speed Recording 3 Changing the Shutter Speed Mode 1 Set the SHUTTER switch to ON. • The shutter speed displayed on the bottom of the screen changes depending on the mode. For modes other than auto, the setting appears highlighted in orange. 2 Slide the SHUTTER switch toward SEL to change the mode. • Repeat step 2 until the desired mode is reached.
Recording 3 Shutter Speed Flicker Reduction [l Camera Setup] You can reduce flicker caused by recording under fluorescent lamps. [Flicker Reduction] 1 Open the [Flicker Reduction] submenu. [Off] 2 Select [Automatic] and then press SET.
Adjusting the Aperture Recording You can affect the brightness of your recordings or change the depth of field by adjusting the aperture. Increase the aperture value (F8 to F9.5) so that objects that are close and far away will be in focus. You can have the camcorder adjust the aperture automatically or you can manually adjust it to give you more control over your recording.
3 Recording Adjusting the Aperture • When you set the aperture value manually, it is not retained if you activate automatic aperture control (excluding full auto mode). The aperture value set automatically by the camcorder will be retained when you switch back to manual aperture control. • When you activate the built-in ND filter, the picture may become dark when you set a high aperture value. In such case, set the ND filter to OFF and readjust the aperture.
Adjusting the Aperture Recording 3 Adjusting the AE Level Use the AE shift control to adjust AE level in order to darken or lighten the image. You can select from 15 AE levels. [l Camera Setup] [AE Shift] 1 Open the [AE Shift] submenu. [l Camera Setup] [AE Shift] [±0] 2 Select an AE level and then press SET. Available AE Levels +2.0 +1.5 +1.25 +1.0 +0.75 +0.5 +0.25 -0.25 -0.5 -0.75 -1.0 -1.25 -1.5 -2.
3 Recording Using the ND Filter Using the ND Filter Using the ND filters allows you keep the aperture within an appropriate range when recording in bright surroundings*. * When recording in bright surroundings, the camcorder closes down the aperture. This may cause the picture to appear blurred depending on the zoom position. Using the ND filter or setting a faster shutter speed can reduce such blur. Operating modes: Set the ND FILTER switch to the desired setting.
White Balance Recording The camcorder uses an electronic white balance process to calibrate the picture for accurate color display under different lighting conditions. There are 4 methods of setting the white balance. 3 White Balance Auto white balance: The camcorder automatically adjusts the white balance to the optimal level. Preset white balance: Set the white balance to either [Daylight] (5,600 K) or [Tungsten] (3,200 K).
Recording 3 White Balance Preset White Balance The camcorder comes preset with outdoor (daylight: 5,600 K) and indoor (incandescent light: 3,200 K) settings. You can fine tune the setting after selecting it. 1 Set the AWB switch to OFF. 2 Set the WHITE BAL. switch to PRESET. 3 Open the [White Balance] submenu. [l Camera Setup] AWB switch 4 Select the desired option and then press SET. WHITE BAL.
White Balance Recording 3 Setting the Color Temperature The following procedure allows you to specify the color temperature between 2,000 K and 15,000 K in 100 K increments. 1 Set the AWB switch to OFF. 2 Set the WHITE BAL. switch to PRESET. 3 Open the [White Balance] submenu. [l Camera Setup] [White Balance] 4 Select [Kelvin] and then press SET. 5 Close the menu and then press the S button. AWB switch • The displayed color temperature appears highlighted in orange.
3 Recording White Balance Recording with a Custom White Balance 1 Set the AWB switch to OFF. 2 Set the WHITE BAL. switch to the desired custom setting, A or B. • The selected custom white balance setting is activated. NOTES • Set the [l Camera Setup] [Tele-converter] setting (0 168) to [Off] in advance. • Readjust the custom white balance if you turn the ND filter on/off or when the light source has changed.
Zooming Recording You can operate the zoom (up to 18x) using the zoom rocker on the side grip or the one on the handle. You can also use the zoom ring on the lens or the zoom buttons on the wireless controller. 3 Zooming Operating modes: Selecting the Zoom Controls Set the ZOOM switch to the desired option. Options RING: ROCKER: Allows you to use the zoom ring.
Recording 3 Zooming Using the Zoom Rockers, Wireless Controller or Optional Remote Control When you operate the zoom, a zoom indicator* will appear on the screen that shows the approximate zoom position. To use the zoom rockers, make sure to set the ZOOM switch to ROCKER in advance. * You can use the [J Other Functions] [Custom Function] [Zoom Indicator] setting (0 124) to set the zoom indicator to a numerical display.
Zooming Recording 3 Approximate zoom speeds (grip zoom rocker) [Grip Rocker] setting [Constant] [Variable] [Speed Level] setting [Constant Speed] setting [Slow] [Normal] [Fast] [1] (slowest) 5 min. 3 min. 1 min. [16] (fastest) 4.5 sec. 2.5 sec. 1.8 sec.* – 4.5 sec. to 5 min. 2.5 sec. to 3 min. 1.8 sec.* to 1 min. * When the zoom speed is too fast (less than 2 seconds end-to-end), the camcorder will have more trouble focusing automatically while zooming.
Recording 3 Zooming Approximate zoom speeds (handle zoom rocker) [Speed Level] setting [Handle Rocker H]/[Handle Rocker L] setting [Slow] [Normal] [Fast] [1] (slowest) 5 min. 3 min. 1 min. [16] (fastest) 4.5 sec. 2.5 sec. 1.8 sec.* * When the zoom speed is too fast (less than 2 seconds end-to-end), the camcorder will have more trouble focusing automatically while zooming.
Onscreen Markers and Zebra Patterns Using onscreen markers allows you to make sure your subject is correctly framed and is within the appropriate safe area. The zebra patterns help you identify areas that are overexposed. The onscreen markers and zebra pattern will not affect your recordings.
Recording 3 Onscreen Markers and Zebra Patterns 4 Select [Enable], select [On] and then press SET to enable the onscreen markers. • All of the selected onscreen markers will be displayed. • Select [Off] to turn off all onscreen markers. Options [Center]: Displays a small marker that indicates the center of the screen. [Horizontal]: Displays a horizontal line to help you compose level shots. [Grid]: Displays a grid that allows you to frame your shots correctly (horizontally and vertically).
Onscreen Markers and Zebra Patterns Recording 3 4 Select a zebra level and then press SET. 5 Press the ZEBRA button to activate the selected zebra pattern. • You can also select [Zebra], select [On] and then press SET. NOTES • You can use the [M LCD/VF Setup] [HD Output] setting (0 170) to display the zebra pattern on an external monitor connected to the HD/SD SDI terminal (b only), HDMI OUT terminal or HD/SD COMPONENT OUT terminal (HD output only).
Recording 3 Setting the Time Code The camcorder can generate a time code signal and embed it in your recordings. You can have the camcorder output the time code signal from the HD/SD SDI terminal (b only) or TIME CODE terminal (b only; 0 88). In addition, you can superimpose the time code on video output from the HDMI OUT terminal, HD/SD COMPONENT OUT terminal, AV terminal or VIDEO 2 terminal.
Setting the Time Code Recording 3 Setting the Time Code’s Initial Value If you set the running mode to [Preset], you can set the initial value of the time code. 1 Open the time code [Setting] submenu. [L TC/UB Setup] [Time Code] [Setting] [L TC/UB Setup] [Time Code] [Setting] 2 Select [Set] and then press SET. • The time code setting screen appears with an orange selection frame indicating the hours. • To reset the time code to [00:00:00.00], select [Reset] instead.
3 Recording Setting the Time Code Putting the Time Code Display on Hold If you set an assignable button to [Time Code Hold] (0 111), you can freeze the display of the time code*. While the time code display is put on hold, [H] will appear on the screen next to the time code and [HOLD] will appear on the side panel. The time code continues to run normally while the time code display is on hold. When you resume the time code display, the current time code will be displayed.
Setting the User Bit Recording The user bit display can be selected from the date or the time of recording, or an identification code consisting of 8 characters in the hexadecimal system. There are sixteen possible characters: the numbers 0 to 9 and the letters A to F. b If user bit information is being received along with an external time code, you can also record the external user bit on the recording media.
3 Recording b Synchronizing with an External Device Using genlock synchronization, you can synchronize this camcorder's video signal to that of an external video device. Similarly, using an external time code signal, you can synchronize this camcorder's time code to the external signal. Using the external time code signal with multiple cameras allows you to set up a multi-camera recording. You can also output the time code signal from this camcorder to achieve the same result.
b Synchronizing with an External Device Recording 3 Using a Reference Video Signal (Genlock Synchronization) When a reference sync signal (analog blackburst or tri-level signal) is input through the GENLOCK terminal, the phases of the camcorder's V and H sync will automatically be synchronized to it. The phase difference between the external Genlock signal and the camcorder is initially set to 0. The H phase can be adjusted within the range of approximately ±0.4 H (HD equivalent).
3 Recording b Synchronizing with an External Device • If the external Genlock signal is incorrect or there is no input signal, the external time code that is recorded may be incorrect. • When an external time code signal is received, the camcorder’s own time code will be synchronized to it and the synchronization will be maintained even if you disconnect the cable from the TIME CODE terminal.
Recording Audio Recording The camcorder features two-channel linear PCM audio recording and playback with a sampling frequency of 48 kHz. You can record audio using the built-in microphone, optional external microphone (XLR terminal) or line input (XLR terminal). You can select the audio input independently for channel 1 and channel 2.
Recording 3 Recording Audio Selecting the Built-in Microphone’s Sensitivity [m Audio Setup] [Audio Input] 1 Open the [Int. Mic Sensitivity] submenu. [m Audio Setup] [Audio Input] [Int. Mic Sensitivity] 2 Select the desired option and then press SET. [Int. Mic Sensitivity] [Normal] Options [Normal]: For recording audio under usual conditions. [High]: For recording audio at a higher volume (+6 dB). Activating the Built-in Microphone’s Attenuator [m Audio Setup] [Audio Input] [Int. Mic Att.
Recording Audio Recording 3 Microphone lock screw Cable clamp Y P O XLR terminals Switching Between External Microphone and Line Input 1 Set the AUDIO IN switch of the desired channel to EXT. 2 Set the XLR terminal switch of the desired channel to LINE or MIC. • To supply a microphone with phantom power, set the switch to MIC+48V instead. Make sure to connect the microphone first, before turning the phantom power on. Keep the microphone connected when turning off the phantom power.
Recording 3 Recording Audio Options [CH1]: Records audio to each channel separately. Audio input into CH1 is recorded to channel 1, while audio input into CH2 is recorded to channel 2. Audio input into CH1 is recorded to both channels. Audio input into CH2 will not be recorded.
Recording Audio Recording 3 Adjusting the Audio Level You can set the audio level to auto or manual for each channel. When both CH1 and CH2 are set to the built-in microphone (0 89), the settings for CH1 will automatically be applied to CH2. Automatic Audio Level Adjustment Set the e switch of the desired channel to A (automatic) to let the camcorder automatically adjust that channel’s audio level.
3 Recording Recording Audio Monitoring the Audio with Headphones Connect headphones to the W (headphone) terminal to monitor the recorded audio. You can use the HEADPHONE +/- buttons to adjust the volume. NOTES • Use commercially available headphones with a cable no longer than 3 m. • When you are monitoring the audio, you can choose to synchronize the audio signal with the video signal or monitor the audio in real time. Use the [m Audio Setup] [Audio Output] [Monitor Delay] setting to select the method.
Using Metadata Recording The camcorder automatically adds metadata to clips while they are being recorded. Metadata consists of the user-defined user memo* and recording data, such as shutter speed, exposure and focus settings. You can use the supplied Canon XF Utility software to check and search for specific metadata.
Recording 3 Colors Bars/Audio Reference Signal You can have the camcorder generate and record color bars and a 1 kHz audio reference signal and output them from the HD/SD SDI terminal (b only), HDMI OUT terminal, HD/SD COMPONENT OUT terminal1, AV terminal, VIDEO 2 terminal1 and W (headphone) terminal2. Colors Bars/Audio Reference Signal 1 2 Outputs color bars only. Outputs audio reference signal only.
Video Scopes Recording The camcorder can display a simplified waveform monitor or vectorscope. It can also display an edge monitor* to help you focus. The video scopes appear only on the LCD screen. They do not appear in the viewfinder or on an external monitor. 3 Video Scopes * The edge monitor looks at the focus of the entire picture and displays the results as a waveform. The edge monitor is available only in mode. Operating modes: Displaying a Video Scope Press the WFM button.
Recording 3 Video Scopes Options [Line]: Sets the waveform monitor to line display mode. [Line+Spot]: The waveform of the area in the red frame is displayed in red on top of the [Line] mode waveform. [Field]: [RGB]: [YPbPr]: Sets the waveform monitor to field display mode. Functions like an RGB parade scope. Functions like a YPbPr parade scope. Configuring the Vectorscope [J Other Functions] The camcorder’s vectorscope function offers 2 modes. You can also change the gain.
Video Scopes Options [Type 1]: [Type 2]: Recording 3 The waveform that represents the focus of the entire picture is displayed in green. In addition, the waveform of the area in the three red frames is displayed in red on top of the previous waveform. This mode displays the edge monitor with the waveform monitor in [Line+Spot] mode. The waveform monitor appears on the left in green while the edge monitor appears on the right in blue.
3 Adding Shot Marks while Recording Recording Adding Shot Marks while Recording When recording, you can flag an important shot in a clip by adding a “shot mark” (n). There are two types of shot marks, shot mark 1 (c) and shot mark 2 (d), and you can add either or both types to a single clip. When the camcorder is in mode, you can add or delete shot marks (0 141). You can also display an index screen of all the shot marks (0 139), allowing you to find a particular scene in a clip more quickly.
Reviewing a Recording When the camcorder is in was recorded. Recording mode, you can review the last clip that Reviewing a Recording [J Other Functions] Operating modes: [Rec Review] 1 Open the [Rec Review] submenu to set the review length. [J Other Functions] 3 [Entire Clip] [Rec Review] 2 Select the desired option and then press SET. 3 After you finish recording, press the U button. • The last clip that was recorded is played back without audio for the selected duration.
Recording 3 Special Recording Modes The camcorder features 4 special recording modes. Special Recording Modes Interval recording ([Interval Rec]): The camcorder will automatically record a pre-defined number of frames at a pre-defined interval. This mode is suitable for recording subjects with little movement, such as natural surroundings or plants. Frame recording ([Frame Rec]): The camcorder will record a pre-defined number of frames every time you press the START/STOP button.
Special Recording Modes Recording 3 Available Intervals* 1 sec 2 sec 3 sec 4 sec 5 sec 6 sec 7 sec 8 sec 9 sec 10 sec 15 sec 20 sec 30 sec 40 sec 50 sec 1 min 2 min 3 min 4 min 5 min 6 min 7 min 8 min 9 min 10 min * In the camcorder’s menu, seconds are indicated by [sec] and minutes are indicated by [min]. Activating Interval Recording Mode and Recording [J Other Functions] 1 Open the [Special Rec] submenu.
Recording 3 Special Recording Modes Frame Recording Mode Set the number of frames in advance. We recommend using the wireless controller or stabilizing the camcorder, for example, on a tripod. Sound is not recorded in this mode. This mode is not available if [J Other Functions] [Bit Rate/Resolution] is set to [35 Mbps 1440x1080]. Configuring Frame Recording Mode [J Other Functions] [Frame Rec] [Rec Frames] 1 Open the [Rec Frames] submenu.
Special Recording Modes Recording 3 • The time code advances by the number of frames recorded. If the running mode of the time code (0 82) is set to [Free Run] or the time code is input from an external source (b only), the running mode will switch to [Rec Run] during special recording mode. When special recording mode is deactivated, the running mode will return to its previous setting.
3 Recording Special Recording Modes 3 Press the START/STOP button to begin recording. • The camcorder automatically records at the set frame rate. • The tally lamps illuminate. • [S&F STBY] changes to [N S&F REC] while recording. 4 Press the START/STOP button again to stop recording. • The camcorder records the clip. • The tally lamps go out and [S&F STBY] appears at the top of the screen. NOTES • You can use only one special recording mode at a time.
Special Recording Modes Recording 3 Pre-recording Mode When pre-recording mode is activated, the camcorder starts recording continuously into a temporary memory of approximately 3 seconds so when you press the START/STOP button, the clip will contain also approximately 3 seconds of video and audio recorded before you pressed the button. [J Other Functions] [Special Rec] [Off] 1 Open the [Special Rec] submenu. [J Other Functions] [Special Rec] 2 Select [Pre Rec] and then press SET.
Recording 3 Optical Axis Shift This function aids in a dual camera setup for 3D recording by allowing you to adjust the position of the image stabilization lens. Optical Axis Shift Operating modes: 1 Open the [Enable] submenu to activate optical axis shift. [l Camera Setup] [Axis Shift] [Enable] [Off] [l Camera Setup] [Axis Shift] [Enable] 2 Select [On] and then press SET. • Y appears on the bottom of the screen. 3 Open the optical axis [Adjust] screen.
Using the Focal Length Guide Recording The focal length guide aids you when using two camcorders for 3D recording. The guide appears as a numerical value and has a range of 195 steps. You can set the guide to 0 at any point in the zoom range to help precisely calibrate both camcorders. 3 Using the Focal Length Guide Operating modes: 1 Set up two camcorders and align their picture angle at full telephoto. [l Camera Setup] 2 Open the [Focal Length Guide] submenu.
3 Recording Using the Focal Length Guide C 110 Y P O
4 Customization Assignable Buttons Customization The camcorder conveniently features 13* buttons to which you can assign various functions. By assigning often-used functions, you can quickly access them with a single press of a button. * In 4 Customization Assignable Buttons mode, only assignable buttons 1 to 7 are available. Operating modes: C Y P O Changing the Assigned Function 1 Open the [Assign Button] submenu.
Customization 4 Assignable Buttons Using an Assignable Button After you assign a function to one of the buttons, press the button to activate the function. For some functions, an options menu may appear. In such case, select the desired option and then press SET. Assignable Functions Functions can be set separately in functions and available modes. mode and Function name mode. Refer to the following table for assignable 0 Description [Standard IS] Turns standard IS on/off.
Custom Picture Settings Customization You can preset a number of picture-related settings (0 117). After changing individual settings to your preference, you can save the whole set in the camcorder or SD card as a custom picture file. You can then load the file at a later date to change the current settings to the preset levels you selected. You can even embed the custom picture settings in clips recorded to a CF card or photos recorded to an SD card.
4 Customization Custom Picture Settings Preset Custom Picture Files By default, the custom picture files in the camcorder in file slots [C7] to [C9] are protected. Remove the protection (0 115) to edit the file. The following describes when to use the preset files. [C7 VIDEO.C]: For playing back video on consumer flat-panel displays. [C8 CINE.V]: For achieving a cinema-like picture on TV monitors, such as when creating TV programs that require a cinema-like effect. [C9 CINE.
Custom Picture Settings Customization 4 Protecting Custom Picture Files Protecting a custom picture file prevents its settings from being accidentally changed. [I X Edit File] [Protect] 1 After selecting a file, open the [Protect] submenu. [I X Edit File] [Protect] 2 Select [Protect] and then press SET. • In the file selection list, h will appear next to the file name. • To remove protection settings, select [Unprotect] instead. 3 Press the CUSTOM PICT. button to exit the custom picture menu.
4 Customization Custom Picture Settings Copying a File from an SD Card to the Camcorder [H X Transfer File] [Copy To Cam.] 1 After selecting a file on the SD card, open the [Copy To Cam.] submenu. [H X Transfer File] [Copy To Cam.] 2 Select the file slot under which to save the file and then press SET. 3 Select [OK] and then press SET. • The currently selected file will be copied to the selected slot on the camcorder, overwriting the file in that slot. 4 Press the CUSTOM PICT.
Custom Picture Settings Customization 4 Available Custom Picture Settings The following are the available settings. Even if no custom picture file is selected, the default settings are still applied to the picture. Gamma The gamma curve changes the overall look of the image. (Default: [Normal 1]). [Normal 1] to [Normal 4]: These settings are suitable for viewing the image on a TV monitor. Highlights in [Normal 2] are brighter than those of [Normal 1].
4 Customization Custom Picture Settings Black Gamma Controls the lower part of the gamma curve (dark areas of the image). [Level]: Raises or lowers the lower part of the gamma curve. This setting can be adjusted from -50 to 50. (Default: 0) [Range]: Selects the range in which dark areas are affected. This setting can be adjusted from -5 to 50. (Default: 0) [Point]: Determines the shape of the lower part of the gamma curve. This setting can be adjusted from -1 to 50.
Custom Picture Settings Customization Knee Point Output Output Knee Slope 4 Input Input Sharpness Y P O Sets the sharpness of the output and recording signal. [Level]: Sets the sharpness level. This setting can be adjusted from -10 to 50. (Default: 0) [H Detail Freq.]: Sets the center frequency of horizontal sharpness. Setting higher values increases the frequency, which, in turn, increases the sharpness. This setting can be adjusted from -8 to 8.
4 Customization Custom Picture Settings [Select]: In addition to the sharpness set by [Level], [Select] sets the sharpness for areas with higher frequencies. Higher values apply more sharpness to areas with higher frequencies. Use this for subjects in which normal sharpening is not effective. This setting is not available when the resolution is 720P. This setting can be adjusted from 0 to 15.
Custom Picture Settings [Y Level]: Customization 4 Adjusts the brightness for detection of skin tones. This setting can be adjusted from 0 to 31. (Default: 16) Selective Noise Reduction The camcorder detects the characteristics of a certain color or tone and applies a noise reduction filter to the targeted areas. A zebra pattern will appear over targeted areas on the screen. [Effect Level]: Adjusts the level of the noise reduction filter. The available options are [Off], [Low], [Middle] and [High].
4 Customization Custom Picture Settings White Balance Adjusts the amount of white balance throughout the whole image. [R Gain]: Adjust the intensity of red tones. This setting can be adjusted from -50 to 50. (Default: 0) [G Gain]: Adjust the intensity of green tones. This setting can be adjusted from -50 to 50. (Default: 0) [B Gain]: Adjust the intensity of blue tones. This setting can be adjusted from -50 to 50.
Custom Picture Settings Customization 4 Other Functions [Setup Level]: Adjusts the black level set by the [Black] and [Master Pedestal] settings. [Level]: Determines the amount of adjustment to be made. This setting can be adjusted from -50 to 50. (Default: 0) [Press]: Compresses the dynamic range of the video signal so that it does not exceed 100%. Available options are [On] and [Off]. (Default: [Off]) [Clip At 100%]: When the video signal exceeds 100%, this function clips the white level at 100%.
Customization 4 Customizing Functions and Onscreen Displays Customize the camcorder to match your shooting style and needs. Use the [J Other Functions] [Custom Function] setting to adjust how some of the camcorder’s controls and functions operate in mode. Similarly, use the [M LCD/VF Setup] [Custom Display] setting to customize the onscreen displays that appear during recording. You can save these preferences along with other menu settings to an SD card and use them again later (0 126).
Customizing Functions and Onscreen Displays Customization 4 Customizing Onscreen Displays For details on which onscreen displays can be customized, refer to Onscreen Displays (0 46). For details on the setting options, refer to [Custom Display] (0 171). [M LCD/VF Setup] [Custom Display] Operating modes: 1 Open the [Custom Display] submenu. [M LCD/VF Setup] [Custom Display] 2 Select the desired onscreen display. 3 Change the setting option and then press SET.
Customization 4 Saving and Loading Camera Settings After you adjust custom picture settings and settings in the various menus, you can save those settings on an SD card. You can load those settings at a later date or on another XF305 or XF300 camcorder so that you can use that camcorder in that same exact way. Saving and Loading Camera Settings Operating modes: Saving Camera Settings to an SD Card [J Other Functions] [Transfer Menu/X] 1 Open the [Save To b] submenu.
5 Playback Playback Playback This section explains how to play back clips recorded on a CF card. For details on playing back clips using an external monitor, refer to Connecting to an External Monitor (0 145). For details on viewing photos on the SD card, refer to Viewing Photos (0 161). 5 Playback Playback Operating modes: Clip Index Screen Y P O Playback functions are accessed from the clip index screen. To open the clip index screen, set the camcorder to mode.
5 Playback Playback 1 2 3 4 5 6 7 8 v Currently selected CF card slot (0 40) Clip thumbnail (0 142) Relay recording: Appears when a clip begins on one CF card and continues on the other.
Playback Playback 5 Playing Back Clips You can play back clips from the clip index screen, [e Mark] index screen and [Z Mark] index screen. Use the playback control buttons on the handle. 1 Move the orange selection frame to the clip you want to play back. 2 Press the D button to start playback. • Playback will start from the clip selected and continue until the end of the last clip in the index screen. When the last frame of the last clip is reached, playback will be paused.
5 Playback Playback 1 2 3 4 5 6 7 8 9 Remaining battery time (0 49) Playback operation Selected CF card Relay recording Time code (0 82) Clip number / Total number of clips Bit rate and resolution (0 51) Frame rate (0 51) Embedded custom picture file (0 113) 1 Appears when [M LCD/VF Setup] [On]. 2 Appears when [M LCD/VF Setup] to [On].
Playback Playback 5 Playback Controls When you play back a clip, operate the buttons on the handle or the wireless controller to use fast playback, play back frame-by-frame or skip clips. Refer to the following table. Available Playback Types Playback type Operation Fast playback Camcorder: Press the J or I button. Wireless controller: Press the J or I button. Repeat to increase the playback speed to approximately 5x J 15x J 60x the normal speed.
Playback 5 Playback Adjusting the Volume During playback, audio will come from the monaural built-in speaker or headphones. When you connect headphones to the W (headphone) terminal, the built-in speaker will be muted. Adjusting the Headphone Volume Press the HEADPHONE +/- buttons to adjust the volume. Y P O Adjusting the Built-in Speaker Volume [m Audio Setup] [Audio Output] [Speaker Volume] [8] 1 Open the [Speaker Volume] submenu.
Clip Operations Playback Besides playing back a clip, you can perform other operations such as deleting a clip or displaying clip information. This is done through the clip menu, which contains different functions depending on the index screen. You can use the functions in the [J Other Functions] menu to perform some of the operations on all the clips. Refer to the following table for available functions and refer to the following pages for more details of the functions.
5 Playback Clip Operations Using the Clip Menu 1 Select a clip and then press SET. • The clip menu appears. Available functions depend on the index screen and which functions are enabled. 2 Select the desired function and then press SET. • The function is enabled. For some functions, further action may be required. Follow the onscreen directions. • Press the CANCEL button instead to return to the clip index screen.
Clip Operations Playback 5 Displaying the User Memo When displaying the [Clip Info] screen of a clip that has an embedded user memo, push the joystick up or turn the SELECT dial up to display it. Push the joystick down or turn the SELECT dial down to return to the [Clip Info] screen.
5 Playback Clip Operations Deleting e Marks or Z Marks Deleting an e Mark or Z Mark from a Clip 1 Select the desired clip and then press SET to open the clip menu. 2 Select [Delete e Mark] or [Delete Z Mark] and then press SET. • The clip information screen appears and it prompts you to confirm the operation. 3 Select [OK] and then press SET. • The screen changes back to the clip index screen the selected mark is deleted. • Select [Cancel] instead to cancel the operation.
Clip Operations Playback 5 Copying All Clips 1 Open the [Copy All Clips] submenu. [J Other Functions] [Clips] [Copy All Clips] 2 Select [OK] and then press SET. • All of the clips on the selected CF card will be copied to the other CF card. • Select [Cancel] instead to cancel the operation. • While the clips are being copied, you can press SET to cancel. [J Other Functions] [Clips] [Copy All Clips] 3 When the confirmation message appears, press SET.
Playback 5 Clip Operations Deleting Clips You can delete any clip except those with an e mark. To delete such clips, delete the e mark beforehand. Deleting a Single Clip 1 Select the desired clip and then press SET to open the clip menu. 2 Select [Delete Clip] and then press SET. • The clip information screen appears and it prompts you to confirm the operation. 3 Select [OK] and then press SET. • Select [Cancel] instead to cancel the operation.
Clip Operations Playback 5 Copying a Custom Picture File Embedded in a Clip You can copy the custom picture file embedded in a clip to the camcorder. 1 Select the desired clip and then press SET to open the clip menu. 2 Select [Copy X File] and then press SET. • The [X Data 1/3] screen appears with the orange selection frame indicating the first custom picture file slot in the camcorder. • Alternatively, you can press the CUSTOM PICT. button.
5 Playback Clip Operations Time code of the frame with the shot mark NOTES • After you finish playing back a clip from this index screen, the index screen that was open before the [Shot Mark] index screen will appear. Y P O Displaying a Frame Index Screen of a Single Clip You can display an index screen of a single clip broken down as frames at fixed intervals. This is useful when you have a long clip or wish to play back a clip from a certain point. You can change how many thumbnails are displayed.
Clip Operations Playback 5 NOTES • After you finish playing back a clip from this index screen, the index screen that was open before the [Expand Clip] index screen will appear. Adding or Deleting Shot Marks from an Index Screen From the [Shot Mark] index screen or [Expand Clip] index screen, you can add/delete a shot mark to/from a frame. You can add or delete both shot marks, only the c mark or only the d mark. Adding a Shot Mark 1 Open the [Shot Mark] index screen or [Expand Clip] index screen.
5 Playback Clip Operations • There may be up to a 0.5 second delay from when you press the button to when the camcorder adds the shot mark. Changing a Clip’s Thumbnail You can change the thumbnail that appears in the clip index screen to a thumbnail of a frame that appears in the [Shot Mark] index screen or [Expand Clip] index screen. 1 Open the [Shot Mark] index screen or [Expand Clip] index screen. 2 Select the desired frame (thumbnail) and then press SET to open the clip menu.
6 External Connections Video Output Configuration External Connections The video signal output from the HD/SD SDI (b only), HDMI OUT and HD/SD COMPONENT OUT terminals depends on the clip’s video configuration, the capability of the external monitor (for video output from the HDMI OUT terminal) and on various menu settings. Video output from the AV or VIDEO 2 terminal will always be in 576/50i standard.
6 External Connections Video Output Configuration NOTES • b When the camcorder is connected via HDMI OUT terminal to an external monitor, the video signal output from the HD/SD SDI terminal will be the same as that from the HDMI OUT terminal. SD Output [N Video Setup] When HD video (16:9 aspect ratio) is converted and output as SD video (4:3 aspect ratio), you can choose how it appears on the external monitor. [SD Output] 1 Open the [SD Output] submenu.
Connecting to an External Monitor External Connections When you connect the camcorder to an external monitor for recording or playback, use the terminal on camcorder that matches the one you wish to use on the monitor. Then, select the video signal output configuration (0 143). The camcorder can output video from all of the video output terminals simultaneously.
6 External Connections Connecting to an External Monitor b Using the HD/SD SDI Terminal [N Video Setup] [SDI Output] [Off] The digital signal output from the HD/SD SDI terminal includes the video signal, audio signal and time code signal. If necessary, perform the following procedure to change the output to HD or SD. Turning the output off will conserve the camcorder’s power. 1 Open the [SDI Output] submenu. [N Video Setup] [SDI Output] 2 Select the desired option and then press SET.
Connecting to an External Monitor External Connections 6 NOTES • If necessary, you can superimpose the onscreen displays on the video displayed on the external monitor (0 147). Using the AV or VIDEO 2 Terminal When you output video from the AV terminal or VIDEO 2 terminal, the video signal is converted to an analog SD composite video signal. While the VIDEO 2 terminal outputs only video, the AV terminal also outputs audio. You can select the SD output method (0 144).
6 External Connections Audio Output The camcorder can output audio from the HD/SD SDI terminal (b only), HDMI OUT terminal, AV terminal or W (headphone) terminal. When audio is output from the AV terminal or W (headphone) terminal, you can configure settings such as the output channel. When audio is output from the AV terminal, you can select the output level.
Audio Output External Connections 6 Selecting the Audio Channel You can select the audio channel that is output from the AV terminal or W (headphone) terminal. [m Audio Setup] [Audio Output] Operating modes: [Channel] 1 Open the [Channel] submenu. [m Audio Setup] [Audio Output] [Channel] [CH1/CH2] 2 Select the desired option and then press SET.
6 Saving Clips to a Computer External Connections Saving Clips to a Computer Use the software on the supplied Canon XF Utilities CD-ROM to transfer clips in the camcorder to a computer to save them. The CD-ROM contains the following. Canon XF Utility: Browser for transferring clips to a computer, playing back and checking video, and managing clips.
Saving Clips to a Computer External Connections 6 Apple's NLE software plugins Refer to the following for the required applications. Canon XF Plugin for Final Cut Pro Canon XF Plugin for Final Cut Pro X Final Cut Pro 6.0.6 / 7.0.0 to 7.0.3 Final Cut Pro X 10.0.3 Refer to the application’s official home page for the application’s system requirements. NOTES • Even if your computer meets the system requirements, proper operation of the software cannot be guaranteed.
6 External Connections Saving Clips to a Computer 3 Select the language to be displayed during installation. 4 Select an installation method and then click [OK]. • If you selected the [Easy Installation] installation method, skip to step 7. C Y P O 5 Select the software to install and the destination folder. Then, click [Next].
Saving Clips to a Computer External Connections 6 6 Click [Install]. 7 Read the license agreement and click [Yes] to begin the installation. • If you do not select [Yes], you cannot install the software. • When the installation has completed, [Installation has completed successfully.] appears. • You can click [Cancel] to cancel the operation. 8 Click [Next] and then click [Finish]. 9 Remove the CD-ROM from the computer.
6 External Connections Saving Clips to a Computer Uninstalling Canon XF MPEG2 Decoder 1 In the Control Panel, open [Programs and Features]* (Windows Vista/ Windows 7) or [Add or Remove Programs] (Windows XP). • A list of installed programs appears. 2 Select [Canon XF MPEG2 Decoder]. 3 Click [Uninstall]/[Uninstall/Change] (Windows Vista/Windows 7) or [Change/Remove] (Windows XP). 4 Follow the onscreen instructions. * This may be [Add or Remove Programs] depending on how the Control Panel is displayed.
Saving Clips to a Computer External Connections 6 4 Click [Install]. 5 Select the installation method and then click [Next]. C Y P O 6 Read the license agreement and click [Agree]. • If you do not select [Agree], you cannot install the software. • If you selected the [Easy Installation] installation method, skip to step 8. 7 Select the software to install and then click [Next].
6 External Connections Saving Clips to a Computer 8 Click [Next] to begin the installation. • When the installation has completed, [Installation has finished.] appears. Y P O 9 Click [Finish] and then remove the CD-ROM from the computer. Uninstalling the Software 1 From [Applications], open [Canon Utilities]. C 2 Move [Canon XF Utility] to the [Trash]. Uninstalling Canon XF Plugin for Final Cut Pro Move the following file to [Trash]. /Library/Application Support/ProApps/MIO/RAD/Plugins/ CanonXF.
Saving Clips to a Computer External Connections 6 Uninstalling Canon XF MPEG2 Decoder Move the following file to [Trash]. /Library/QuickTime/XFMpeg2Dec.component Uninstalling the Instructions for Apple's NLE Software Plugins 1 From [Applications], open [Canon Utilities]. 2 Move [Canon XF Plugin for Final Cut Pro] or [Canon XF Plugin for Final Cut Pro X] to [Trash]. Uninstalling the Instructions for Avid's NLE Software Plugins 1 From [Applications], open [Canon Utilities].
6 External Connections Saving Clips to a Computer Mac OS: 1 From [Applications], open [Canon Utilities] [Manual]. Desired plugin 2 Open the folder of the language and double-click the PDF file.
7 Photos Taking Photos Photos You can take photos when the camcorder is in mode or you can capture a photo from a clip when the camcorder is in mode. Photos are saved onto the SD card. In mode, photo size is 1920x1080*. In mode, photo size depends on the resolution setting of the clip that the photo is captured from. If the clip is 1920x1080 or 1440x1080, the photo size is 1920x1080. If the clip is 1280x720, the photo size is 1280x720.
7 Photos Taking Photos Capturing Photos in MEDIA Mode You can capture a photo from a clip during playback pause. To capture a photo, set an assignable button to [Photo] first or use the wireless controller. Operating modes: 1 Set an assignable button to [Photo] (0 111). • This step is not necessary if you are using the wireless controller. 2 Select the desired clip and press the D button to start playback. 3 Pause the playback at the point you want to capture.
Photo Playback Photos You can view the photos that you took with the camcorder. 7 Photo Playback Operating modes: Displaying the [Photos] Index Screen Display the [Photos] index screen to view photos. 1 Hold down the button on the d switch and move it to MEDIA. • The camcorder switches to appears. mode and the clip index screen 2 Press the INDEX button. • The index screen selection menu appears. 3 Select [Photo Index] and then press SET. Y P O • The [Photos] index screen appears.
7 Photo Operations Photos Photo Operations You can use the photo menu to protect or unprotect a photo, delete a photo, or copy a custom picture file embedded in a photo. You can display the photo menu from the [Photos] index screen or photo playback screen. Using the Photo Menu 1 From the [Photos] index screen, select a photo and then press SET. • If you are viewing a photo, simply press SET. • The photo menu appears. Available functions depend on the photo’s settings.
Photo Operations Photos 7 5 Select [OK] and then press SET. • Select [Cancel] instead to cancel the operation. • The selected photo is deleted. • If a custom picture file is embedded in the photo, it is also deleted. 6 When the confirmation message appears, press SET. Deleting All Photos [J Other Functions] 1 Open the [Delete All Photos] submenu. [J Other Functions] [Delete All Photos] 2 Select [OK] and then press SET. • All of the photos on the SD card will be deleted.
7 Photos Photo Operations Protecting a Photo from the Index Screen 1 Open the [Photos] Index Screen • Refer to Viewing Photos (0 161). 2 Move the orange selection frame to the photo to be protected. 3 Press SET to open the photo menu. 4 Select [Protect] and then press SET. • To remove protection settings from a protected photo, select [Unprotect] instead. • The screen prompts you to confirm the operation. 5 Select [OK] and then press SET.
Photo Operations Photos 7 Copying a File from the Index Screen 1 Open the [Photos] Index Screen. • Refer to Viewing Photos (0 161). 2 Move the orange selection frame to the photo with the custom picture file to be copied. 3 Press SET to open the photo menu. 4 Select [Copy X File] and then press SET. • The [X Data 1/3] screen appears with the orange selection frame indicating the first file slot in the camcorder. • Alternatively, you can press the CUSTOM PICT. button.
7 Photos Photo Operations NOTES • If you select [Continu.] and the SD card you insert already contains a photo with a larger number, a new photo will be assigned a number one higher than that of the last photo on the SD card. • We recommend using the [Continu.] setting.
8 Additional Information Menu Options Additional Information 8 Additional Information Menu Options For details about how to select an item, refer to Using the Menus (0 28). For details about each function, see the reference page. Menu items without a reference page are explained after the tables. Setting options in boldface indicate default values. Menu items not available appear grayed out.
Additional Information 8 Menu item [Zoom] Menu Options Submenu Setting options [Speed Level] [Fast], [Normal], [Slow] [Grip Rocker] [Constant], [Variable] [Constant Speed] 1-16 (8) 0 76 76 [Handle Rocker H] 1-16 (16) [Handle Rocker L] 1-16 (8) [Wireless Controller] 1-16 (8) 78 [Focal Length Guide] [Set To 0], [Off] 109 77 [Tele-converter] [On], [Off] – [Flicker Reduction] [Automatic], [Off] 66 [WA-H82], [Off] – [Wide Attach.
Menu Options Additional Information 8 [m Audio Setup] menu Menu item [Audio Input] Submenu [CH1], [CH1/CH2] N – 91 [Int. Mic Low Cut] [Off], [LC1], [LC2] N – 89 [Int. Mic Sensitivity] [Normal], [High] N – 90 [Int. Mic Att.] [On], [Off] N – 90 [XLR1 Mic Trimming] [XLR2 Mic Trimming] [+12 dB], [+6 dB], [0 dB], [-6 dB], [-12 dB] N – 92 [XLR1 Mic Att.] [On], [Off] N – 92 [XLR2 Mic Att.
Additional Information 8 Menu Options [M LCD/VF Setup] menu Menu item Submenu 0 Setting options [Brightness] -99 to 99 (0) N N [Contrast] -99 to 99 (0) N N [Color] -20 to 20 (0) N N [Sharpness] 1 to 4 (2) N N [Backlight] [Normal], [Bright] N N [Brightness] -99 to 99 (0) N N [Contrast] -99 to 99 (0) N N [Color] -20 to 20 (0) N N [Sharpness] 1 to 4 (2) N N [Backlight] [Normal], [Bright] N N [LCD/VF B&W] [On], [Off] N N 33 [LCD/VF Simul.
Menu Options Additional Information Menu item [Custom Display] Submenu 0 Setting options [Remaining Battery] [Warning], [Normal], [Off] N – [Remaining Rec Time] [Warning], [Normal], [Off] N – [Rec Mode] [On], [Off] N – [Time Code] [On], [Off] N – [Zoom Position] [Always On], [Normal], [Off] N – [Light Metering] [On], [Off] N – [Custom Picture] [On], [Off] N – [ND Filter] [Warning], [Normal], [Off] N – [Focus Ring Warn.
8 Additional Information Menu Options [Custom Display] settings [Remaining Battery]: Controls when the remaining battery indicator appears. [Warning]: Appears only when there is a warning. [Normal]: Always appears on the screen. [Remaining Rec Time]: Displays the remaining recording time. [Warning]: Appears only when there is a warning. [Normal]: Always appears on the screen. [Rec Mode]: Displays the recording operation indicator ([STBY] in record pause mode, for example) when set to [On].
Menu Options Additional Information 8 [Interval Counter]: Displays the countdown during interval recording mode when set to [On]. [SD Card Status]: Controls when the SD card status indicator appears. [Warning]: Appears only when there is a warning. [Normal]: Always appears on the screen. [Bit rate/Resolution]: Displays the bit rate and resolution when set to [On]. [Frame Rate]: Displays the frame rate when set to [On].
Additional Information 8 Menu item [WFM (LCD)]1 Menu Options Submenu N – 97 – N 97 [Line], [Line+Spot], [Field], [RGB], [YPbPr] N N [1x], [2x] N N [Spot], [Normal] N N [1x], [5x] N N [Type 1], [Type 2] N – 98 [Deutsch], [English], [Español], [Français], [Italiano], [Polski], [ ], [ ], [ ], [ ] N N 27 [WFM], [VS], [Edge Mon.
Menu Options Additional Information Menu item Submenu 8 0 Setting options [SDI Rec Command] (b only) [On], [Off] N – – [Photo Numbering] [Reset], [Continu.] N N1 165 N – 116 – N6 163 [Add X File] [To Clip] [On], [Off] [To Photo] [On], [Off] [Delete All Photos] [Custom Function] [OK], [Cancel] [Shockless Gain] [Fast], [Normal], [Slow], [Off] N – [Shockless WB] [On], [Off] N – [AE Response] [Fast], [Normal], [Slow] N – [Iris Limit] [On], [Off] N – [I.
8 Additional Information Menu Options [Number Setting]: Determines the last 4 digits of the clip name. Combined with the [Title Prefix] setting, this constitutes the 6-character clip name. Select [Set] to assign a desired number to the first clip you record or select [Reset] to reset the number to [0001]. The numerals increase every time a clip is recorded. [Delete Last Clip]: Deletes the last clip you recorded.
Displaying the Status Screens Additional Information 8 Displaying the Status Screens You can use the status screens to check the camcorder’s various recording- and playback-related settings. You can also output the status screens on an external monitor. Operating modes: 1 Press the STATUS button. • The status screen most recently displayed will appear unless you turned off the camcorder or changed the operating mode.
Additional Information 8 [Camera] Status Screen ( Displaying the Status Screens mode) 1 2 3 4 5 6 7 1 2 3 4 5 6 8 9 10 11 Gain (0 61) Gain limit (0 61) Autofocus mode (0 57) Grip zoom rocker setting (0 76) Zoom speed of handle zoom rocker (0 77) Zoom speed of wireless controller (0 78) [Buttons / Remote] Status Screen C 7 8 9 10 11 Flicker reduction (0 66) Focus limit (0 59) Face AF (0 58) Zoom speed level (0 76) Zoom speed of grip zoom rocker (0 76) Y P O 1 1 2 1 Assignable buttons 1 to 13*
Displaying the Status Screens Additional Information 8 [Audio] Status Screen In mode 1 2 3 4 5 6 7 In 8 9 10 11 mode 12 7 1 2 3 4 5 6 Built-in microphone low-cut filter (0 89) Built-in microphone sensitivity (0 90) XLR terminal recording channel (0 91) External microphone sensitivity (0 92) Audio limiter (0 93) Audio output delay (0 148) [Media] Status Screen C Y P O 7 8 9 10 11 12 4 5 6 7 8 9 10 11 1 2 3 1 2 3 4 5 6 CF card A CF card B SD card Total space on CF card A Used space on CF card
Additional Information 8 Displaying the Status Screens NOTES • Depending on the recording media, the total space displayed on the screen may differ from the capacity listed on the CF card or SD card.
Displaying the Status Screens Additional Information 8 [Battery / Hour Meter] Status Screen 1 2 3 4 5 1 2 3 Remaining recording time Remaining recording time indicator Battery life indicator [X Data 1/3] Status Screen ( 1 2 3 4 5 6 7 8 1 2 3 4 5 6 4 5 Total operation time (0 176) Operation time since using [Reset Hour Meter] (0 176) Y P O mode) C Custom picture file name (0 113) Gamma (0 117) Master pedestal (0 117) Master black RGB levels (0 117) Black gamma settings (level, range and point) (
Additional Information 8 [X Data 2/3] Status Screen ( Displaying the Status Screens mode) 1 2 3 4 5 6 7 1 2 3 Sharpness settings (level, horizontal detail frequency, horizontal/vertical detail balance, and limit) (0 119) Sharpness settings (select, knee aperture gain and slope) (0 119) Level depend settings (level, slope and offset) (0 120) [X Data 3/3] Status Screen ( 1 2 3 4 5 6 7 8 1 2 3 4 C mode) 5 6 Coring settings (level, offset, curve and depth) (0 119) Noise reduction (0 120) Color matri
Troubleshooting Additional Information 8 Troubleshooting If you have a problem with your camcorder, refer to this section. Consult your dealer or a Canon Service Center if the problem persists. Power source The camcorder will not turn on or it turns off by itself. - The battery pack is exhausted. Replace or charge the battery pack. - Remove the battery pack and reattach it correctly. Cannot charge the battery pack. - The temperature of the battery pack is outside the charging range.
8 Additional Information Troubleshooting Playback Cannot delete a clip. - You cannot delete clips with an e mark. Remove the e mark (0 136) to delete the clip. Deleting clips takes longer than usual. - When the CF card contains a large number of clips, some operations may take longer than usual. Save your clips (0 150) and initialize the CF card (0 39). Cannot delete a photo. - The photo is protected. Remove the protection (0 115). - The LOCK switch on the SD card is set to prevent accidental erasure.
Troubleshooting • Use the [Other Functions] except for the hour meter. Additional Information 8 [Reset All Settings] function. This resets all the camcorder’s settings to default values Video noise appears on screen. - Keep a distance between the camcorder and devices that emit strong electromagnetic fields (plasma TVs, cellular phones, etc.). Horizontal bands appear on the screen.
8 Additional Information Troubleshooting Connections with External Devices Video noise appears on a nearby TV screen. - When using the camcorder in a room where a TV is located, keep a distance between the compact power adapter and the power or antenna cables of the TV. Playback looks fine on the camcorder but there is no image on the external monitor. - The camcorder is not connected correctly to the external monitor. Make sure you are using the correct connection (0 145).
Troubleshooting Additional Information 8 CF AJCF B / CF BJCF A Switched - This message appears when you use the SLOT SELECT button to switch the CF card slot in use or recording continued from one CF card to the other. CF AJCF B / CF BJCF A Will switch in a moment - The CF card is almost full so recording will continue on the other CF card in approximately 1 minute. CF A/CF B Buffer overflow. Recording was stopped.
8 Additional Information Troubleshooting Do not disconnect the USB cable or the power source until you safely end the connection from the computer. Cannot write data with this connection. To write data to the camcorder, connect the compact power adapter then reconnect the camcorder and computer. - The camcorder cannot be operated while it is not being powered by the compact power adapter and is connected to a computer with a USB cable. In addition, clips cannot be written back to the camcorder.
Troubleshooting Additional Information 8 Shot Mark Error - Could not add a shot mark. If the message appears in mode, try adding the mark again. If that does not work, add the mark in mode after you finish recording. If the message appears in mode, turn off the camcorder and then back on. Then, try to add the mark again. System error - Turn off the camcorder and back on again. If this does not solve the problem, there may be a malfunction with the camcorder. Consult a Canon Service Center.
8 Additional Information Handling Precautions Handling Precautions Camcorder Be sure to observe the following precautions to ensure maximum performance. • Do not carry the camcorder by the LCD panel. Be careful when closing the LCD panel. • Do not leave the camcorder in places subject to high temperatures (like the inside of a car parked under direct sunlight), or high humidity. • Do not use the camcorder near strong electromagnetic fields such as above TVs, near plasma TVs or mobile phones.
Handling Precautions Additional Information 8 Long-term storage • Store battery packs in a dry place at temperatures no higher than 30 °C. • To extend the battery life of the battery pack, discharge it completely before storing it. • Charge and discharge all your battery packs fully at least once a year. Always attach the battery terminal cover. Do not allow any metal objects to touch the terminals (figure 1), as this can cause a short circuit and damage the battery pack.
8 Additional Information Handling Precautions • SD cards: SD cards have a physical switch to prevent writing on the card so as to avoid the accidental erasure of the card’s content. To write-protect the SD card, set the switch to the LOCK position. LOCK switch Built-in Rechargeable Lithium Battery The camcorder has a built-in rechargeable lithium battery to keep the date/time and other settings.
Maintenance/Others Additional Information 8 Maintenance/Others Cleaning Camcorder Body • Use a soft, dry cloth to clean the camcorder body. Never use chemically treated cloths or volatile solvents such as paint thinner. Lens and Instant AF Sensor • If the lens surface or Instant AF sensor is dirty, autofocus may not work properly. • Remove any dust or dirt particles using a non-aerosol type blower brush.
8 Additional Information Maintenance/Others Condensation may form in the following cases: • When the camcorder is moved quickly from cold to warm places • When the camcorder is left in a humid room • When a cold room is heated rapidly To avoid condensation • Do not expose the camcorder to sudden or extreme changes in temperature. • Remove the recording media and battery pack.
Optional Accessories Additional Information 8 Optional Accessories The following optional accessories are compatible with this camcorder. The availability differs from area to area.
Optional Accessories Additional Information 8 Use of genuine Canon accessories is recommended. This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack).
Optional Accessories Additional Information 8 c Bit rate 50 Mbps Usage time BP-955 BP-975 BP-950G BP-970G Viewfinder 295 min. 450 min. 310 min. 435 min. LCD screen 285 min. 430 min. 295 min. 405 min. Viewfinder 195 min. 280 min. 195 min. 275 min. LCD screen 185 min. 265 min. 185 min. 260 min. Playback LCD screen 365 min. 550 min. 380 min. 530 min. Recording (maximum) Viewfinder 295 min. 450 min. 310 min. 435 min. LCD screen 285 min. 430 min. 300 min. 405 min.
8 Additional Information Optional Accessories WA-H82 Wide Attachment The wide attachment decreases the camcorder’s focal length by a factor of 0.8, allowing you to make recordings with a wider angle of view. Remote Controller When the ZR-2000 or ZR-1000 is connected to the camcorder’s REMOTE terminal, it is possible to control functions such as the start and stop of recording, the zoom and the focus functions while reviewing the picture on an external monitor without touching the camcorder.
Specifications Additional Information 8 Specifications XF305 / XF300 System • Recording System Movies: Video compression: MPEG-2 Long GOP; Audio compression: Linear PCM, 16 bits, 48 kHz, 2 channels File type: MXF Photos: Image compression: JPEG DCF (Design rule for Camera File system), compatible with Exif Ver. 2.
8 Additional Information Specifications • White Balance Auto white balance, custom white balance, preset white balance settings or color temperature setting • Iris: Auto or manual setting • Gain: Auto (AGC) or manual (-6.0 dB to 33.0 dB, fine-tuning available) • Shutter speed: Auto, speed, angle, clear scan or slow shutter mode, off; 1/3 sec to 1/2000 • Minimum Illumination: 0.06 lux (FULL AUTO switch is OFF, [Frame Rate] at [50i], gain at 33 dB, shutter speed at 1/3) • Subject Illumination Range: 0.
Specifications Additional Information 8 • b GENLOCK Terminal BNC jack, input only: 1 Vp-p/75 Ω • b TIME CODE Terminal BNC jack Input: 0.5 V – 18 Vp-p/10 kΩ Output: 1 Vp-p/75 Ω • REMOTE Terminal ∅ 2.5 mm stereo mini-jack • USB Terminal mini-B, USB 2.0 (Hi-Speed USB) Power/Others • Power supply (rated) 7.4 V DC (battery pack), 8.4 V DC (DC IN) Y P O • Power consumption (Recording at 50 Mbps with AF on, viewfinder/LCD screen normal brightness, SDI output off) b Viewfinder: 8.5 W, LCD screen: 8.
8 Additional Information Specifications BP-955 Battery Pack • Battery type Rechargeable lithium ion battery, compatible with Intelligent System • Rated voltage 7.4 V DC • Operating temperature 0 – 40 °C • Battery capacity Typical: 5,200 mAh Minimum: 37 Wh / 4,900 mAh • Dimensions (W x H x D) 38.2 x 43.5 x 70.5 mm • Weight 220 g C Y P O Weight and dimensions are approximate. Errors and omissions excepted. The information in this manual is verified as of May 2012. Subject to change without notice.
Index A Abroad, using the camcorder . . . . . . . . . . . . . .194 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .195 AE level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 AGC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 AGC limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 Aperture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Aspect ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index screens Changing clip thumbnail . . . . . . . . . . . .142 Clips . . . . . . . . . . . . . . . . . . . . . . . . . . .127 Expand clip . . . . . . . . . . . . . . . . . . . . .140 Shot marks . . . . . . . . . . . . . . . . . . . . . .139 Initializing recording media . . . . . . . . . . . . . . . . .39 Interval recording mode . . . . . . . . . . . . . . . . . .102 Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Iris limit . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal covers . . . . . . . . . . . . . . . . . . . . . . . . .35 Time code . . . . . . . . . . . . . . . . . . . . . . . . . .82, 87 TIME CODE terminal* . . . . . . . . . . . . . . . . . . . . .87 Tripod . . . . . . . . . . . . . . . . . . . . . . . . . . . .36, 190 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .183 Turning the camcorder on/off . . . . . . . . . . . . . . .25 W Waveform monitor . . . . . . . . . . . . . . . . . . . . . . 97 White balance . . . . . . . . . . . . . . . . .
Canon Inc. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan Canon Europa N.V. Bovenkerkerweg 59-61, 1185 XB Amstelveen, The Netherlands www.canon-europa.com Canon UK Ltd CCI Service Centre, Unit 130, Centennial Park, Borehamwood, Hertfordshire, WD6 3SE, United Kingdom Telephone 0870-241-2161 Canon Australia Pty Ltd Tel: 13-13-83 (within Australia only) (61) 02-9805-2555 www.canon.com.au Canon New Zealand Ltd Tel: 0800-222-666 (within New Zealand only) (64) 09-489-0300 www.canon.co.
