PUB.
Important Usage Instructions Introduction WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. COPYRIGHT WARNING: Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be contrary to copyright laws. Digital Video Camcorder, XL H1A Systems. This device complies with Part 15 of the FCC Rules.
IMPORTANT SAFETY INSTRUCTIONS In these safety instructions the word “product” refers to the Canon Digital Video Camcorder XL H1A and all its accessories. 1. Read Instructions — All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions — The safety and operating instructions should be retained for future reference. 3. Heed Warnings — All warnings on the product and in the operating instructions should be adhered to. 4.
19. Damage Requiring Service — Disconnect this product from the wall outlet and all power sources including battery, and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If any liquid has been spilled onto, or objects have fallen into, the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally even if you follow the operating instructions.
Using this Manual Thank you for purchasing the Canon XL H1. Please read this manual carefully before you use the camcorder and retain it for future reference. Should your camcorder fail to operate correctly, refer to the Troubleshooting table ( 144). E Conventions Used in this Manual : Precautions related to the camcorder operation. : Additional topics that complement the basic operating procedures. : Reference page number.
About the HD/HDV and SD/DV Specifications Throughout the manual we will distinguish between the video signal standards used by the camera section of the XL H1, and the recording standards used by the recorder section of the XL H1. The video signal can be set to HD (high definition) or SD (standard definition) specifications. The recording standard on the tape will be HDV (high definition) or DV, respectively.
Contents Introduction Important Usage Instructions............................................................................................................................. 2 Important Safety Instructions............................................................................................................................. 3 Using this Manual ..............................................................................................................................................
Playback Playing Back a Tape ........................................................................................................................................ 98 Connecting to a Monitor/TV........................................................................................................................... 100 Audio Output .................................................................................................................................................
Checking the Supplied Accessories Body Kit CA-920 Compact Power Adapter DC-920 DC Coupler Two AA (R6) Batteries Color Viewfinder Microphone Unit Adapter Holder DTC-1000 Component Video Cable Stereo Cable E BP-950G Battery Pack SDC-16M SD Memory WL-D5000 Wireless Card Controller Camcorder Dust Cap SS-1000 Shoulder Strap Introduction Additional Accessories Supplied with the Lens Kit Canon HD Video 5.
Components Guide XL H1 Left side view POWER dial External control mode VCR/PLAY mode Power off Auto Shutter-Priority Aperture-Priority Recording Manual programs Spotlight Night Easy Recording LIGHT button END SEARCH button ( 49) MODE SELECT switch ( 48) FRAME RATE switch ( 56) AUDIO MONITOR button ( 67, 104) POWER indicator Side panel ( 135) Color viewfinder socket ( 19) FU-1000 Monochrome Viewfinder socket ( 150) EVF PEAKING/EVF MAGNIFYING buttons ( 53) EXP.
Left side view E Introduction Dioptric adjustment lever ( 21) STEREO/MONO microphone selector ( Lock lever ( 20) Eye cup ( 20) Color viewfinder ( 19-22) Lock release button ( 21) Viewfinder cable ( 19) Zoom ring ( 50) Lens hood ( 25) Focus ring ( 52) 64) RESET button Memory card slot ( 30) ND filter operating ring ( 55) ND filter unlock button ( 55) STABILIZER ON/OFF switch ( 68) POSITION PRESET switch ( 51) AF switch ( 52)/ POSITION PRESET ON/SET switch ( Focus selector ( 53) 51) 11
Right side view S-video terminal ( 102) Video terminal (BNC) ( 102) RCA/BNC selector ( 102) Video terminal (RCA) ( 102) AUDIO 2 terminals (RCA) ( 66) AUDIO 1 terminals (RCA) ( 64) Terminal cover Battery attachment unit ( 16) BATT. RELEASE button ( 16) HD/SD SDI terminal ( 100) GEN.
Front view E Back view Introduction Tally lamp ( 97) Remote sensor ( 28, 109) Grip belt ( 23) Attachment sockets for the optional TA-100 Tripod Adapter ( 150) Tripod socket* Viewfinder cable ( 19) Remote sensor ( 28, 109) Start/stop button ( 42) Microphone locking screw ( 22) Strap mount ( 23) XLR input terminals ( 65, 66) SHUTTER buttons ( 72) PHONES LEVEL dial (phones) terminal HDV indicator ( 47) HDV/DV IN/OUT terminal ( 102, 110, 113) terminal LINE/MIC switch ( 65, 66) +48V switch ( 65, 66) MIC ATT
Top view (pause) button ( 98) / DRIVE MODE button ( 119) (stop) button ( 98,110) / (metering mode) button ( 121) (rewind) button ( 98) / - button ( 124) (play) button ( 98) / SLIDESHOW button ( 124) (fast forward) button ( 98) / + button ( 87, 124) REC (record) button ( 110) Screw holes for adapter holder ( 23) Tally lamp ( 97) 14 Remote sensor ( 28, 109) Handle zoom lever ( 50) Viewfinder locking screw ( 19) Microphone ( 22) Advanced accessory shoe ( 66, 122) Start/stop button ( 42) PHOTO button ( 116)
WL-D5000 Wireless Controller E Introduction PHOTO button ( 116) START/STOP button ( 42) MENU button ( 31) TV SCREEN button ( 132) SLIDESHOW button ( 124) DATA CODE button ( 108) INDEX WRITE button ( 91) AUDIO MONITOR button ( 67, 104) END SEARCH button ( 49) SEARCH SELECT button ( 106, 107) REC PAUSE button ( 110) REW button ( 98) ZERO SET MEMORY button ( 105) button ( 98) PAUSE button ( 98) REMOTE SET button ( 109) AV DV button ( 112) Zoom buttons ( 50) Menu selection buttons ( 31) SET button ( 31) - b
Preparing the Power Supply Preparations Charging the Battery Pack Disconnect the DC coupler from the power adapter before charging. Remove the terminal cover of the battery pack. 1. Connect the power cord to the adapter. 2. Plug the power cord into a power outlet. 3. Attach the battery pack to the adapter. • Press lightly and slide the battery pack in the direction of the arrow until it clicks. • The charge indicator starts flashing. The indicator will stay on when the charging is complete. 4.
Using a Household Power Outlet 1. Turn the POWER dial to OFF. 2. Attach the DC coupler to the camcorder. E Press lightly and slide the DC coupler up, in the direction of the arrow until it clicks. 3. Connect the power cord to the power adapter. 4. Plug the power cord into a power outlet. 5. Connect the DC coupler to the adapter. 6. Detach the DC coupler after use. Holding the BATT.RELEASE button pressed down, slide the DC coupler down to remove it.
Charging, Recording and Playback Times The following times are approximate and vary according to the charging, recording and playback conditions.
Preparing the Camcorder Attaching and Detaching the Color Viewfinder Unit E Attaching the Color Viewfinder Unit 1. Slide the viewfinder unit onto the bracket and tighten the locking screw. 2. Connect the viewfinder cable to the upper socket of the camcorder body. 3. Hook the viewfinder cable onto the cable clamp. Insert the cable plug straight into the camcorder socket. Preparations Detaching the Viewfinder Unit 1. Detach the viewfinder cable. 2.
Attaching and Detaching the Eye Cup You can change the position of the eye cup for use with either the left or right eye. Detach the eye cup and reattach it when changing the position of the eye cup for right or left eye use. Attaching the Eye Cup Align the hole for the dioptric adjustment lever with the lever, and pull the eye cup into position. Right eye use Left eye use Detaching the Eye Cup Detach the eye cup as shown in the illustration.
Dioptric Adjustment Turn on the camcorder and adjust the dioptric adjustment lever. E Prevent direct sunlight from getting in the viewfinder. The viewfinder LCD may become damaged due to concentration of the light by the lens. Pay special attention when mounting the camcorder on a tripod, or during transportation. Using the Viewfinder as LCD Panel You can use the viewfinder as an LCD panel by opening the eyepiece adapter. Press the lock release button and open the eyepiece adapter.
Adjusting the Viewfinder You can adjust the brightness, contrast, color and sharpness of the viewfinder. These adjustments will not affect your recording. MENU ( 31) DISPLAY SETUP / EVF SETUP BRIGHTNESS••• CONTRAST••••• COLOR•••••••• SHARPNESS•••• 1. Press the MENU button. 2. Turn the SELECT dial to select [DISPLAY SETUP/ ] and press the SET button. 3. Select [EVF SETUP] and then select [BRIGHTNESS], [CONTRAST], [COLOR] or [SHARPNESS]. 4.
Fastening the Grip Belt Adjust the grip belt so that you can reach the zoom lever with your index and middle finger, and the start/stop button with your thumb. E Attaching the Shoulder Strap Pass the ends through the strap mount and adjust the length of the strap. Be careful not to drop the camcorder when adjusting the strap or the grip belt.
Preparing the Lens Refer also to the instruction manual of the lens. Mounting the Lens 1. Set the POWER dial to OFF. 2. Remove the dust caps from the camcorder and the lens. 3. Align the red mark on the lens with the red mark on the camcorder and turn the lens clockwise until it clicks. Removing the Lens 1. Set the POWER dial to OFF. 2. Slide in the LENS RELEASE switch, turn the lens counter-clockwise until it stops and remove the lens. 3. Attach the dust caps to the camcorder and the lens.
Proper operation cannot be guaranteed when recording in HDV standard with the optional Extender XL 1.6x. The message “HD INCOMPATIBLE LENS” will appear when using the extender, even with an HDV compatible lens. E Attaching the Lens Hood Attach the lens hood to protect the lens and shade it from stray light. 1. Place the lens hood on the front of the lens and screw it clockwise until the Canon logo appears on top. • Be careful not to deform the lens hood.
Adjusting the Flange Back (Lenses without a built-in flange back adjustment function) The flange back can be adjusted to correct the focus during telephoto and wide zooming. The flange back can be adjusted automatically by the camcorder (AF) or manually (MF). Different flange back adjustment values can be memorized and can also be saved as backup. You can store flange back settings for up to 10 lenses. Preparations 1. Set the frame rate to 60i or 30F. 2.
Resetting the flange back adjustments This procedure will reset the stored flange back adjustment value for the mounted lens. 1. 2. 3. 4. 5. Press the MENU button. Turn the SELECT dial to select [CAMERA SETUP] and press the SET button. Select [FB] and then select [SET DEFAULT]. Select [YES] and press the SET button. Press the MENU button to close the menu. E In the following cases the flange back cannot be adjusted correctly and the camcorder will return to the flange back adjustment selection screen.
Using the Wireless Controller When you press the buttons on the wireless controller, point it at one of the camcorder’s remote sensors. The camcorder has three remote sensors: two at the front and one at the back. Inserting the Batteries The wireless controller operates with two AA (R6) batteries. 1. Open the battery cover. 2. Insert the batteries following the + and – markings. 3. Close the battery cover. The camcorder and wireless controller are equipped with 2 remote sensor modes ( 109).
Loading/Unloading a Cassette Use only videocassettes marked with the logo. For recording in HDV we recommend you use videocassettes compatible with the HDV standard. E 1. Slide the EJECT switch to open the cassette compartment cover. The cassette compartment opens automatically. 2. Load/unload the cassette. • Insert the cassette straight, fully into the compartment with the window facing out. • Unload the cassette by pulling it straight out. Preparations 3. Close the cassette compartment cover.
Inserting/Removing a Memory Card You can use SD memory cards or commercially available MultiMediaCards (MMC) with this camcorder. The SD memory card has a protect switch to prevent accidental erasure. Inserting the Card 1. Set the POWER dial to OFF. 2. Open the memory card slot cover. 3. Insert the memory card straight, all the way into the card slot. 4. Close the card slot cover. Do not force the cover closed if the card is not correctly inserted.
Changing Settings with the MENU Button Many of the camcorder’s functions can be changed from the onscreen menu. E SELECT dial SET button MENU button Selecting Menus and Settings Press the MENU button to open the menu. Turn the SELECT dial to select a submenu and press the SET button. Turn the SELECT dial to select a menu item and press the SET button. Turn the SELECT dial to select a setting option and press the SET button. Press the MENU button to close the menu.
Menu and Default Settings Default settings are shown in boldface. CAMERA MENU Submenu SIGNAL SETUP CAMERA SETUP *Only in Standard Definition (SD). Menu Item TIME CODE EXT.SYNC GENLCK ADJUST T.CODE OUT COMP. OUT SDI OUTPUT SDI SPEC. 24F MODE SEL* ZEBRA ZEBRA LEVEL SKIN D.SET F SPEED PSET2 CLEAR SCAN FB 1 2 Setting Options FRAME DROP, NON-DROP SETTNG COUNT-UP REC-RUN, REC-RUN PS.
CAMERA MENU Submenu CUSTOM PRESET Menu Item EDIT 82 E Preparations Setting Options SELECT CP 1 PRESET_A, 2 PRESET_B, 3 PRESET_C, 4 PRESET_D, 5 PRESET_E, 6 PRESET_E TUNE RENAME PROTECT RESET RETURN GAMMA NORMAL, CINE1, CINE2 KNEE AUTO, LOW, MIDDLE, HIGH BLACK STRETCH, MIDDLE, PRESS MASTER PED. -9 ~ +9 SETUP LEVEL -9 ~ +9 SHARPNESS -9 ~ +9 H DTL FREQ LOW, MIDDLE, HIGH DTL HV -9 ~ +9 BALANCE CORING -9 ~ +9 NR1 OFF, LOW, MIDDLE, HIGH NR2 OFF, LOW, MIDDLE, HIGH COLOR MAT.
CAMERA MENU Submenu RECORDING SETUP AUDIO SETUP *Only in Standard Definition (SD). Menu Item REC MODE* UB REC UB SELECT IMG QUALITY IMAGE SIZE STILL I. REC Setting Options SP, LP INT. USR-BIT, EXT. USR-BIT 00 00 00 00, TIME, DATE SUPER FINE, FINE, NORMAL L 1440x1080, S 640x480 OFF, ON, ON+CP DATA FILE NOS. AUDIO MODE RESET, CONTINUOUS HDV 2CH, 4CH DV 48kHz 2CH, 32kHz 2CH, 32kHz 4CH OFF, -12dB, -20dB NORMAL, LINE OUT ON , OFF OFF, 12dB 1kHz TONE AUD.M.
VCR/PLAY MENU Submenu SIGNAL SETUP RECORDING SETUP AUDIO SETUP Menu Item TIME CODE PLAYBACK STD T.CODE OUT COMP. OUT SDI OUTPUT SDI SPEC. AV DV HD DOWN-CONV REC MODE* UB SELECT IMG QUALITY HD STILL SIZ FILE NOS. SEL AUDIO CH MIX SELECT AUDIO MODE WIND SCREEN R-XLR GAINUP Setting Options FRAME DROP, NON-DROP SETTNG COUNT-UP REC-RUN, REC-RUN PS.
VCR/PLAY MENU Submenu DISPLAY SETUP/ Menu Item EVF SETUP TV SCREEN AUDIO LEVEL DISPLAYS CUSTOM KEYS DATA CODE SYSTEM/ LANGUAGE 6 SEC.DATE UB DISPLAY CUSTOM KEY 1 CUSTOM KEY 2 WL. REMOTE TALLY LAMP D/TIME SET LED ON/OFF 36 Setting Options EVF BW MODE ON, OFF BRIGHTNESS CONTRAST COLOR SHARPNESS ON, OFF ON, OFF ON, OFF ON, OFF DATE, TIME, DATE & TIME, CAMERA DATA, CAM.
CARD CAMERA MENU Submenu SIGNAL SETUP CAMERA SETUP Menu Item GENLOCK GENLCK ADJUST COMP. OUT SDI OUTPUT SDI SPEC. ZEBRA ZEBRA LEVEL SKIN D.SET F SPEED PSET1 FB FOCUS PRI. REVIEW 1 Setting Options ON, OFF -1023 – +1023 480i, 1080i/480i ON, OFF AUTO, SD LOCKED ON, OFF 70, 75, 80, 85, 90, 95, 100 HUE CHROMA AREA Y LEVEL SKIN DETAIL OFF, LOW , MIDDLE HIGH LOW, MIDDLE, HIGH AF ADJUST MF ADJUST SET DEFAULT ON, OFF OFF, 2 sec., 4 sec., 6 sec., 8 sec., 10 sec.
CARD CAMERA MENU Submenu CUSTOM PRESET RECORDING SETUP AUDIO SETUP 38 Menu Item EDIT IMG QUALITY IMAGE SIZE FILE NOS.
CARD CAMERA MENU Submenu DISPLAY SETUP/ Menu Item EVF SETUP SYSTEM/ LEV/CENT MRK OBJ DST UNIT ZOOM IND. TV SCREEN GUIDE INFO LANGUAGE CUSTOM KEY 1 CUSTOM KEY 2 WL. REMOTE POWER SAVE D/TIME SET LED ON/OFF IRIS DIAL Setting Options EVF BW MODE ON, OFF 92 BRIGHTNESS 22 CONTRAST COLOR SHARPNESS OFF, LEVEL MARK, CENT.
CARD VCR/PLAY MENU Submenu SIGNAL SETUP Menu Item Setting Options COMP. OUT 480i, 1080i/480i SDI OUTPUT ON, OFF SDI SPEC.
Setting the Time Zone, Date and Time Set the time zone, date and time when you first start using your camcorder, or if the built-in rechargeable battery has completely discharged. E Setting the Time Zone/Daylight Saving Time MENU ( 31) SYSTEM/ D/TIME SET T.ZONE/DST•••N.Y. 1. Press the MENU button. 2. Turn the SELECT dial to select [SYSTEM/ ] and press the SET button. 3. Select [D/TIME SET ] and then select [T.ZONE/DST] and press the SET button. The time zone setting appears.
Recording Recording Before You Begin Recording Make a test recording first to check if the camcorder operates correctly. If necessary, clean the video heads ( 138). The camcorder ships with the following factory settings: Recording mode - HDV; Audio mode - 2 channels About the audio recording, refer to the relevant chapter ( 63). Recording 1. Remove the lens cap. 2. Press the lock button and set the POWER dial to a recording program. 3. Press the start/stop button to begin recording.
The end search, date search and index search functions may not work correctly if you mix recordings in HDV and DV standards on the same tape. Low-angle Recording The carrying handle is equipped with a duplicate set of recording and zoom controls, ideal for low-angle recording. Slide the LOCK lever towards the lens to prevent accidental operation.
Screen Displays during Recording Time code You can select between drop frame or non-drop frame time code ( 58). Remaining tape Indicates the remaining time of the tape in minutes. “ END” flashes when the tape reaches the end. • When the time left is less than 15 seconds, the remaining tape time may not appear. • Depending on the tape, the indication may not be displayed correctly. Remaining battery charge The battery symbol indicates the charge status of the battery pack.
You can select the amount of information shown on the screen from full, partial or no display. Repeatedly pressing the EVF DISPLAY button will cycle through the options in the following sequence.
Reviewing the Recording (record review) button In record pause mode, this function allows you to review the last few seconds of your recording to check if it has been recorded properly. Press and release the (record review) button. The camcorder rewinds the tape, plays back the last few seconds, and returns to record pause mode. If the current video signal standard is different from the signal standard in which the tape was recorded, the recording will not be played back correctly.
Selecting the Signal Standard (HD/SD) E MODE SELECT switch Set the MODE SELECT switch to the desired position. • HD: To record on the tape in HDV standard or to use the camcorder as a high-definition (HD) camera. • SD 16:9, SD 4:3: To record on the tape in DV standard or to use the camcorder as a standard-definition (SD) camera. Select the aspect ratio as desired.
SD Changing the Aspect Ratio When recording in standard definition (SD), you can change the aspect ratio of your recording to 16:9 or 4:3. MODE SELECT switch Set the MODE SELECT switch to SD 16:9 or SD 4:3. The camcorder’s viewfinder has a 16:9 aspect ratio. If you select the 4:3 aspect ratio, the picture will appear in the center of the screen with black side panels. If you change the position of the MODE SELECT switch while recording, the aspect ratio will not change immediately.
End Search You can use this function to locate the end of the last recorded scene. E END SEARCH button Press the END SEARCH button. • “ ” appears. • The camcorder rewinds/fast forwards the tape, plays back the last few seconds of the recording and stops the tape. • Pressing the button again cancels the search. 49 Recording End search cannot be used once you unload the cassette. End search may not work properly if there is a blank section between recordings on the tape.
Zooming You can operate the zoom from either the side grip or the carrying handle. You can also use the zoom ring on the zoom lens or the zoom buttons on the wireless controller. Zoom lever Zoom buttons Zoom ring ZOOM SPEED dial ZOOM SPEED switch Move the zoom lever toward W to zoom out (wide-angle). Move it toward T to zoom in (telephoto).
Zoom Preset (Lenses equipped with the zoom preset function) This function enables any given zoom setting to be memorized and to return to that zoom setting instantly. E POSITION PRESET switch POSITION PRESET ON/SET switch Presetting the Zoom 1. Set the POSITION PRESET switch to ZOOM. 2. Move the POSITION PRESET ON/SET switch to SET. The preset zoom position appears in yellow on the zoom indicator. Returning to the Preset Zoom Position The camcorder returns to the preset zoom position.
Adjusting the Focus The camcorder can be set to Autofocus or Manual Focus. To make it easier to focus manually, you can also make use of the Peaking and Magnifying display functions ( 53). If you are not using the HD 20x L IS Lens, refer also to the instruction manual of the lens you are using. AF switch Focus ring Focus selector Autofocus (Lenses equipped with the autofocus function) Autofocus is set when the focus selector on the lens is set to AF.
Manual focus E EVF PEAKING/ EVF MAGNIFYING buttons AF switch/POSITION PRESET ON/SET switch Focus selector 1. Lenses equipped with autofocus function: Slide the focus selector on the lens to M. “MF” is displayed on screen. 2. Zoom in to telephoto. 3. Turn the focus ring to adjust the focus. 4. Operate the zoom to reframe the subject. If you focus manually and then leave the camcorder with the power turned on, you may lose the focus on your subject.
Peaking While recording or in record pause, press the EVF PEAKING button. • The outlines of the subject will be emphasized. • Press the button again to cancel the function. Magnifying In record pause, press the EVF MAGNIFYING button. • The central part of the screen will be magnified approximately 2x. • Press the button again to cancel the function.
Using the ND Filter (Lenses with Built-in ND Filter) When recording in bright surroundings, the camcorder will set a small aperture value and the picture may appear blurred.When you are using a lens with built-in ND filter, turn it on/off according to the screen display. E ND filter unlock button ND filter operating ring With the HD 20x L IS Lens: Press the ND filter unlock button and turn the ND filter operating ring.
Selecting the Frame Rate You can select from the following frame rates depending on the recording mode: HD 60i, 30F, 24F (2:3 pulldown-converted) SD 60i, 30F, 24F (2:3 pulldown-converted or 2:3:3:2 pulldown-converted) 60i Mode Records in 60 fps interlaced mode, the same as TV signals. 30F Mode Records in 30 fps progressive mode and outputs signals converted into 60 fps interlaced. 30F (camera) 60i (tape) 24F Mode HD Records in 24 fps progressive mode.
E FRAME RATE switch Selecting the Frame Rate Set the FRAME RATE switch to the desired position. • i: 60i Mode, F1: 30F Mode, F2: 24F Mode. • The selected frame rate appears on-screen. If you change the position of the FRAME RATE switch while recording, the frame rate will not change immediately. It changes once you pause recording. SD Selecting the 24F Pulldown Mode ( 31) CAMERA SETUP Recording MENU 24F MODE SEL•2:3 Open the menu and select [CAMERA SETUP].
Setting the Time Code Selecting the Frame Setting In 60i and 30F mode, you can select between drop frame or non-drop frame time code. MENU ( 31) SIGNAL SETUP TIME CODE FRAME SETTNG•DROP Open the menu and select [SIGNAL SETUP]. Select the [TIME CODE] submenu and then [FRAME SETTNG]. Select a setting option and close the menu. When you select the [NON DROP] setting or when you select 24F frame rate in SD mode, “NDF” will appear on the side panel display.
In 24F (in SD) mode, the “frames” value of the time code is set in multiples of 5. When you change the frame rate from 60i/30F to 24F, the “frames” value of the time code will automatically become a multiple of 5. When you mix drop frame and non-drop frame time codes (including 24F frame rate in SD mode), the time code at the point where the recording starts may be discontinuous.
Synchronizing the Camcorder’s Time Code You can synchronize this camcorder’s time code to an external time code generator. Also you can include in the recording the user bit signal received from the TC IN terminal ( 62). The camcorder offers the following synchronization options. Genlock The V phase and H phase of the camcorder’s time code generator will be synchronized to the external signal being received from the GEN.LOCK terminal.
Selecting the Synchronization Method MENU ( 31) SIGNAL SETUP E EXT. SYNC•••OFF Open the menu and select [SIGNAL SETUP]. Select [EXT. SYNC], select a setting option and close the menu. 61 Recording If you select the [GENLOCK+TC] synchronization method, the [FRAME SETTNG] and [COUNTUP] settings of the camcorder will be ignored and the external time code’s drop-frame bit will be used instead (if the external time code is non-drop frame, “NDF” will appear on the side panel display).
Setting the User Bit The user bit display can be selected from the date or the time of recording, or an identification code consisting of 8 characters in the hexadecimal system that is useful for labeling tapes. There are sixteen possible characters: the numbers 0 to 9 and the letters A to F. If a user bit is being received along with an external time code, you can also choose to record the external user bit on tape. MENU ( 31) RECORDING SETUP UB SELECT•••00 00 00 00 1.
Audio Recording When recording on the tape in either HDV or DV standard, you can select to record audio in only two channels or all four channels simultaneously. E HDV The audio transfer rate is 384 Kbps when recording on 2 channels, and 384 Kbps (192 Kbps / 2 channels) when recording on all 4 channels. The sampling frequency is 48 kHz in all modes. DV You can choose to record in 16 bit audio mode (sampling frequency 48 kHz), or 12 bit audio mode (sampling frequency 32 kHz).
Using the Wind Screen With the supplied microphone (only), you can reduce the sound of wind recorded from the front microphone. MENU ( 31) AUDIO SETUP WIND SCREEN•••ON Open the menu and select [AUDIO SETUP]. Select [WIND SCREEN], select a setting option and close the menu. Recording on Channels 1 and 2 Select the audio input from FRONT MIC (supplied microphone), AUDIO1 (RCA terminals) or REAR (XLR terminals). Refer also to the Audio Block Diagram ( 157).
When Connecting to the XLR terminals 1. Connect a microphone to the XLR terminals. To supply a microphone with phantom power, set the +48V switch to ON. Make sure to connect the microphone first, before turning on the phantom power. Keep the microphone connected when turning off the phantom power. E 2. Set the INPUT SELECT switch to REAR. 3. Set the REC CH SELECT switch to CH1 or CH1·CH2.
Recording on Channels 3 and 4 Select the audio input from SHOE (optional MA-300 Microphone Adapter), AUDIO2 (RCA terminals) or REAR (XLR terminals). Refer also to the Audio Block Diagram ( 157). Make sure to set [AUDIO MODE] to [4 CH] when recording on the tape in HDV standard, or [32kHz 4CH] when recording in DV standard. When Connecting to the Advanced Accessory Shoe 1. Attach the optional MA-300 Microphone Adapter to the advanced accessory shoe.
When connecting a microphone that does not support phantom power, make sure to set the +48V switch to OFF. Otherwise the microphone may be damaged. E Adjusting the Audio Recording Level CH1, CH2, CH3, CH4 dials REC LEVEL switch AUDIO MONITOR button Hiding/Displaying the Audio Level Indicator on the Screen MENU ( 31) DISPLAY SETUP/ AUDIO LEVEL••ON Open the menu and select [DISPLAY SETUP/ option and close the menu. ].
Image Stabilizer (Lenses Equipped with Image Stabilizer) You can select to activate or turn off the image stabilizer depending on the recording conditions. STABILIZER ON/OFF switch Move the STABILIZER ON/OFF switch to OFF. The image stabilizer cannot be turned off in the Easy Recording mode. We recommend turning off the image stabilizer when mounting the camcorder on a tripod. The image stabilizer is designed to compensate for a normal degree of camcorder shake.
Using the Programmed AE Modes Programmed auto exposure modes provide advanced automated recording techniques ensuring professional results in various shooting conditions. E Selecting the Programmed AE Modes Press the button and turn the POWER dial. The symbol of the selected mode appears. POWER dial Do not change the mode during recording as the brightness of the image may change abruptly.
Aperture-Priority ( 73) Use this mode to select between 7 aperture settings–from f/1.6 to f/9.5 (or to full iris close)–and the camcorder automatically sets a matching shutter speed. This mode allows for the best control of depth of field. Manual ( 74) This mode offers the creative freedom of a complete range of manual controls. In the Manual mode, you have the option to set the exposure at any combination of shutter speed and aperture levels.
Availability of functions in each recording program Recording programs EXP. LOCK button IRIS dial SHUTTER button AE SHIFT dial GAIN dial WHITE BALANCE dial Custom preset adjustments CUSTOM PRESET SELECT button CUSTOM PRESET ON/OFF button Skin detail Clear Scan Frequency selection of Clear Scan : Available 1: 2: 1 E 1 1 1 (0) (auto) (auto) (0 dB) 2 (0) (auto) 2 : Not available Available when the exposure is locked. Available during clear scan.
Recording in the Shutter-Priority (Tv) Mode POWER dial SHUTTER button SHUTTER button Available shutter speeds when recording movies depend on the selected frame rate: 60i/30F 24F 1/4*, 1/8, 1/15, 1/30, 1/60, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/8000, 1/15000, CS (clear scan) 1/3*, 1/6, 1/12, 1/24, 1/48, 1/60, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/8000, 1/15000, CS (clear scan) Available shutter speeds when recording still images: 1/4*, 1/8, 1/15, 1/30, 1/60, 1/100, 1/250, 1/500 * O
Recording in the Aperture-Priority (Av) Mode E IRIS dial POWER dial Available aperture values (with the HD 20x L IS lens) F1.6, F2.0, F2.8, F4.0, F5.6, F8.0, F9.5, CLOSE 1. Set the POWER dial to Av. 2. Select the aperture with the IRIS dial. You can select the direction in which turning the IRIS dial will adjust the aperture values, using the [IRIS DIAL] option of the [SYSTEM/ ] submenu. 73 Recording Other settings such as the shutter speed are set automatically.
Recording in the Manual Mode You can set the exposure at any combination of shutter speed and aperture levels.
Adjusting the Exposure EXP. LOCK button E POWER dial GAIN dial IRIS dial SHUTTER button SHUTTER button Exposure Lock 1. Set the POWER dial to , Tv or Av. 2. Press the EXP. LOCK button. • The exposure indicator appears. Use the exposure indicator as an estimate. • The mark above the indicator denotes the automatic exposure setting. The mark of the indicator denotes the current exposure setting within ±2 stops (beyond 2 stops, the marker will blink).
Using AE Shift You can use the AE Shift control to manually override the automatic exposure system to darken or lighten the image. Select from 13 AE levels (+2.0, +1.5, +1.0, +0.75, +0.5, +0.25, ±0, -0.25, -0.5, -0.75, -1.0, -1.5, -2.0). AE SHIFT dial POWER dial 1. Set the POWER dial to , Tv or Av. 2. Turn the AE SHIFT dial to adjust the level. The selected level appears.
Adjusting the Gain The gain control adjusts the level of the video signal generated depending on the lighting and shooting conditions. You can select from automatic gain control or preset levels that range from -3 to +18 dB. -3 dB Auto 0 dB +3 dB/+6 dB/ +12 dB/+18 dB E For the lowest noise recording for indoor, low light or low contrast scenes. Automatic adjustment of gain. For lifelike night scenes or scenes under artificial lighting. Increases the brightness in indoor or low-light scenes.
Setting the White Balance The camcorder uses an electronic white balance process to calibrate the picture for accurate color display under different lighting conditions. In addition to the fully automated mode, white balance modes include an indoor mode, an outdoor mode, a color temperature setting and two user presets that can be memorized.
Setting a Custom White Balance 1. 2. 3. 4. Set the POWER dial to a recording program other than . Press the WHITE BALANCE dial so that it pops out. Set the WHITE BALANCE dial to one of the custom preset numbers. Point the camcorder at a white object and zoom in until it fills the whole screen. E Keep the camcorder zoomed at the white object until step 5 is completed. 5. Press the WHITE BALANCE button.
Using the Zebra Pattern This camcorder has a zebra pattern feature that shows black and white diagonal stripes over the area that is overexposed. The zebra pattern is only displayed on the screen and will not affect your recordings. The zebra pattern will not be displayed while using the EVF Peaking and EVF Magnifying functions. Use this feature to guide the adjustment of the aperture and shutter speed. Available zebra pattern settings: 70 IRE, 75 IRE, 80 IRE, 85 IRE, 90 IRE, 95 IRE, and 100 IRE.
Using the Skin Detail Function With the skin detail function, areas in the picture that have skin-tone characteristics will be detected, and the details in these areas will be softened in order to conceal skin imperfections. On the viewfinder, those skin areas will be identified by a zebra pattern alternating with the normal picture (on a connected TV or computer screen a white pattern will appear instead).
Using the Custom Preset You can define preset levels for 23 recording specifications used when recording on tape (17 when recording still images on the memory card). Up to 6 custom presets can be stored on the camcorder, and up to 20 can be stored on the memory card. You can copy the camcorder’s custom presets to the memory card.
Master Pedestal [PED] (only in CAMERA mode) Adjust the master pedestal level in the range -9 to +9. E Setup Level [SET] (only in CAMERA mode) Adjust the setup level in the range -9 to +9. • Depending on the value set for the master pedestal [PED], the setup level may not be able to take a negative value. In that case, adjusting the setup value within a certain value range will have no effect. Sharpness [SHP] Adjust the sharpness level in the range -9 to +9.
Color Phase [CPH] Adjust the color phase in the range -9 to +9. R Gain [RGN] Adjust the red level in the range -9 to +9. G Gain [GGN] Adjust the green level in the range -9 to +9. B Gain [BGN] Adjust the blue level in the range -9 to +9. R-G Matrix [RGM] Adjust the level in the range -9 to +9. R-B Matrix [RBM] Adjust the level in the range -9 to +9. G-R Matrix [GRM] Adjust the level in the range -9 to +9. G-B Matrix [GBM] Adjust the level in the range -9 to +9.
CUSTOM PRESET ON/OFF button CUSTOM PRESET SELECT button E SELECT dial MENU button Setting the Custom Preset Settings MENU ( 31) CUSTOM PRESET EDIT SELECT CP 1. Open the menu and select [CUSTOM PRESET]. 2. Select [ EDIT]. The custom preset submenu appears. 3. Select [SELECT CP] and then select the name of the custom preset file where you want to store the settings. After making the selection you will return to the custom preset edit submenu. Recording 4. From the edit submenu, select [TUNE].
3. Turn the SELECT dial to select a number, letter or punctuation mark and press the SET button. • The next character of the custom preset file name will start flashing. • Set the rest of the custom preset file in the same way. 4. When you finish renaming the custom preset file, press the SET button. You will return to the custom preset submenu. 5. Close the menu. Protecting a Custom Preset File 1. Open the menu and select [CUSTOM PRESET], followed by [ 2. From the edit submenu, select [PROTECT]. EDIT].
Copying a Custom Preset File to the Memory Card 1. Open the menu and select [CUSTOM PRESET], followed by [ ]. 2. From the copy submenu, select [SELECT CP] and then select the name of the custom preset file you want to copy to the card. 3. Select [SAVE POSITION] and select the filename under which you want to store the file on the memory card. E • Up to 20 custom preset files can be stored on the memory card.
Saving the Custom Preset Settings in Use with a Still Image on the Memory Card In mode, you can save the custom preset settings currently being used on the memory card along with a still image of the recording. This is very useful when you want to load the custom preset file later by selecting the still image of that specific scene. Open the menu and select [RECORDING SETUP]. Select [STILL I. REC], set it to [ON + CP DATA] and close the menu. While you are recording on the tape, press the PHOTO button.
Using Clear Scan This feature allows you to record a computer’s CRT screen or other equipment without displaying black band or flicker on the screen. You can adjust the frequency from 60.1 Hz to 203.9 Hz. E POWER dial SHUTTER MENU ( 31) CAMERA SETUP buttons CLEAR SCAN•••60.1Hz 1. Set the POWER dial to Tv or M. 2. Press the SHUTTER button to display “CS”. 3. Open the menu and select [CAMERA SETUP]. Select [CLEAR SCAN], adjust the frequency and close the menu.
Using the Custom Keys You can assign frequently used functions to the custom keys. The custom keys can have different functions assigned to them in each of the different operation modes.
Changing the Custom Keys Setting MENU ( 31) SYSTEM/ E CUSTOM KEY 1•INDEX WRITE Open the menu and select [SYSTEM/ ]. Select [CUSTOM KEY 1] or [CUSTOM KEY 2], select the function you wish to assign to the custom key and close the menu. When you do not wish to use the custom keys, select [(NONE)]. Activating the Functions with the Custom Key Time Code ( 58) Press the CUSTOM KEY (1 or 2) button. The time code setting menu appears.
Time Code Hold You can press the custom key button to freeze the display of the time code. The time code will continue running normally even while the time code display is on hold. Time Code Hold can only be operated with the custom keys. Press the CUSTOM KEY (1 or 2) button. • Pressing the custom key button again will reactivate the normal display of the time code. • While on hold, the time code will be displayed with an H next to it and “HOLD” appears on the side panel display.
Recording Color Bars/Audio Reference Signal Color Bars You can generate and record SMPTE (Society of Motion Picture and Television Engineers) color bars. E BARS/FADE SELECT button BARS/FADE ON/OFF button 1. Press the BARS/FADE SELECT button to display “COLOR BARS”. • Repeatedly pressing the button will cycle through the options in the following order: COLOR BARS, WHITE FADE, BLACK FADE, no display. • “COLOR BARS” starts flashing. 2. Press the BARS/FADE ON/OFF button.
Using the Faders You can choose to fade to/from white or to/from black. 1. While recording or in record pause mode, press the BARS/FADE SELECT button to display “WHITE FADE” or “BLACK FADE”. • Repeatedly pressing the button will cycle through the options in the following order: COLOR BARS, WHITE FADE, BLACK FADE, no display. • The selected fader display starts flashing. 2. Press the BARS/FADE ON/OFF button. The selected fader display stops flashing. 3. Press the start/stop button.
Using the Digital Video Control This feature enables the XL H1 to control the record and stop functions of a connected IEEE1394 storage/recording device. The device must comply with the IEEE1394 AV/C protocol. E Windows XP (SP2) users can use the CONSOLE software (sold separately) to download video and audio recordings (in HDV or DV standards) from the camcorder to the computer’s hard disk. For details refer to the software’s help modules. MENU ( 31) SYSTEM/ DV CONTROL•••OFF 1.
Other Camcorder Functions/Settings Changing the Recording Mode (SP/LP) When recording in Standard Definition (SD mode) only, you can choose between SP (standard play) and LP (long play). LP extends the tape usage by 1.5 times. MENU ( 31) RECORDING SETUP REC MODE•••••SP To change to LP mode, open the menu and select [RECORDING SETUP]. Select [REC MODE], set it to [LP] and close the menu. Depending on the tape and its usage condition, the picture and sound recorded in LP mode may be distorted.
Turning Off the Tally Lamps MENU ( 31) SYSTEM/ TALLY E LAMP•••ON Open the menu and select [SYSTEM/ the menu. ]. Select [TALLY LAMP], set it to [OFF] and close The tally lamps still light up when the camcorder receives a signal from the wireless controller. Changing the Display Language The language used in the camcorder displays and menu items can be changed to Simplified Chinese or Japanese.
Playing Back a Tape Playback If the playback picture is distorted, clean the video heads using a Canon Head Cleaning Cassette or a commercially available digital video head-cleaning cassette ( 138). Select a playback standard according to the tape you wish to play back. REC SEARCH +/– buttons 1. Set the POWER dial to . 2. Open the menu and select [SIGNAL SETUP]. Select [PLAYBACK STD] and set it to [AUTO], [HDV] or [DV] to match the tape you wish to playback. 3. Close the menu.
(Frame Advance) Plays back frame-by-frame. Repeatedly press the button on the wireless controller during playback pause. Hold the button pressed down to enter the continuous frame advance playback. E (Slow Forward) Plays back at about 1/3 normal speed. Press the SLOW button on the wireless controller during normal or reverse playback. Press the (play) button to return to normal playback. DV (Playback Pause) To pause playback, press the during normal playback.
Connecting to a Monitor/TV The different recording modes and the corresponding output terminals are given in the table below: HD HD/SD SDI Terminal 1920x1080 COMPONENT OUT HDV/DV Terminal (D-) Terminal D3 (1440x1080) MPEG TS SD in 4:3 640x480 D1 (SD) Normal DV (SD) SD in 16:9 640x480 D1 (SD) DV (SD) (S-) VIDEO Terminals Connection to a High Definition TV or Monitor (HDTV/HiVision) 1 Using the SD/HD SDI Terminal The audio signal is separate from the component video signal Stereo Cable (supplie
Activate the HD/SD SDI output and select the appropriate video output option (HD or SD). 1. Set the POWER dial to . 2. Open the menu and select [SIGNAL SETUP]. Select [SDI OUTPUT] and set it to [ON]. 3. From the same [SIGNAL SETUP] submenu select [SDI SPEC.]. Select [AUTO] or [SD LOCKED] to match the video output you wish to use. 4. Close the menu.
3 Using the HDV/DV Terminal DV Cable (commercially available) 4-pin 6-pin • When connecting the camcorder to a monitor TV that supports DV, you may need to carry out a procedure on the TV to recognize the camera. Refer to the instruction manual of the TV or monitor. • If necessary, turn on the DV conversion and select whether to convert a tape recorded in HD to SD with the following procedure. Open the menu and select [SIGNAL SETUP]. Select [HD DOWN-CONV], select a setting option and close the menu.
We recommend powering the camcorder from a household power outlet. When connecting to the RCA terminal, set the RCA/BNC selector down to RCA. When connecting to the BNC terminal, set the RCA/BNC selector up to BNC. TV sets with S1-Video terminals: Recording made with a 16:9 aspect ratio ( 48) will automatically be played in widescreen mode if you connect the camcorder to the TV using the S1VIDEO terminal.
Audio Output AUDIO2 RCA terminals SET button SELECT dial AUDIO1 RCA terminals MENU button AUDIO MONITOR button Selecting the Audio Output of the RCA Terminals Press the AUDIO MONITOR button. Repeatedly pressing the button will cycle through the options in the following sequence: CH 1/2 , CH 3/4 and CH 1/2 / CH 3/4 . Selecting the Audio Channels MENU ( 31) AUDIO SETUP SEL AUDIO CH•CH 1/3 / CH 2/4 Open the menu and select [AUDIO SETUP].
Returning to a Pre-marked Position If you wish to return to a particular scene later, mark the point with the zero set memory, and the tape will stop at that point when you rewind/fast forward the tape. E This function is operated with the wireless controller. REW button ZERO SET MEMORY button STOP button 1. Press the ZERO SET MEMORY button at the point you wish to return to later. • The tape counter is reset to 0:00:00 and the mark appears. • To cancel, press the ZERO SET MEMORY button again. 2.
Index Search With the index search you can locate any point you have marked beforehand with an index signal ( 91). This function is operated with the wireless controller. / buttons SEARCH SELECT button 1. Press the SEARCH SELECT button to display “INDEX SEARCH”. “ ” appears. 2. Press the or button to begin searching. • Press more than once to search for further index signals (up to 10 times). • Press the STOP button to stop searching. Playback may start slightly before or after the index signal.
Date Search You can locate the change of the date/time zone with the date search function. E This function is operated with the wireless controller. / buttons SEARCH SELECT button 1. Press the SEARCH SELECT button to display “DATE SEARCH”. “ ” appears. 2. Press the or button to begin searching. • Press more than once to search for further date changes (up to 10 times). • Press the STOP button to stop searching. 107 Playback A recording of longer than a minute per date/time zone is required.
Displaying the Data Code The camcorder maintains a data code containing the recording date and time and other camera data such as shutter speed, gain and exposure (f-stop). MENU button MENU button DATA CODE button SELECT dial SET button Selecting the Data Code Display Combination MENU ( 31) DISPLAY SETUP / DATA CODE••••DATE & TIME Open the menu and select [DISPLAY SETUP/ option and close the menu. ].
Changing the Remote Sensor Mode Two remote sensor modes and an off setting are available to prevent interference from other Canon wireless controllers being used nearby. E Turning the Remote Sensor Off MENU ( 31) SYSTEM/ WL.REMOTE•••• Open the menu and select [SYSTEM/ close the menu. “ 1 ]. Select [WL.REMOTE], set it to [OFF ] and ” appears. Changing the Remote Sensor Mode MENU ( 31) SYSTEM/ WL.REMOTE•••• 1 1. On the camcorder, open the menu and select [SYSTEM/ it to [ 2] and close the menu.
Recording an External Video Signal (Analog Line-In, HDV/DV In) Editing You can record on the tape an external video signal, either from the analog video input (SD standard) or from the HDV/DV input (SD or HD standard). Analog Line-In You can select the audio channels to be recorded along with the video signal. 1. Connect the camcorder to the analog video device. For the connection diagram to an analog device refer to Section 4 of Connecting to a Monitor/TV ( 102). 2.
Recording is not possible unless the [PLAYBACK STD] option is set to [AUTO] ( 35). E Copyright Signal Certain software tapes are copyright protected. If you attempt to play back such tape, “COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED” appears and you will not be able to view the contents of the tape. If you attempt to record from such tape via the DV terminal, “COPYRIGHT PROTECTED DUBBING RESTRICTED” appears and you will not be able to record the contents of the tape.
Converting Analog Signals into Digital Signals (Analog-Digital Converter) Using the camcorder you can convert analog video input signals to a digital video signal (SD standard) and output it through the HDV/DV terminal. MENU ( 31) SIGNAL SETUP AV DV••••••••OFF Open the menu and select [SIGNAL SETUP]. Select [AV DV], set it to [ON] and close the menu. Depending on the signal sent from the connected device, the conversion from analog to digital signals might not work properly (e.g.
Connecting to a Computer (IEEE1394) To connect the camcorder to a computer you need to ensure the following requirements: a computer equipped with an IEEE1394 (DV) terminal and video editing software with video capturing capability installed. For the minimum system requirements for video editing, refer to the instruction manual of the video editing software.
Selecting the Image Quality/Size Using a Memory Card Changing the Still Image Quality You can choose from Superfine, Fine and Normal. MENU ( 31) RECORDING SETUP IMG QUALITY••FINE Open the menu and select [RECORDING SETUP]. Select [IMG QUALITY], select a setting option and close the menu. Changing the Still Image Size You can choose from 1920 x 1080, 848 x 480, 1440 x 1080 and 640 x 480 pixels. MENU ( 31) RECORDING SETUP IMAGE SIZE•••1440x1080 Open the menu and select [RECORDING SETUP].
File Numbers Still images are automatically assigned file numbers from 0101 to 9900, and stored in folders containing up to 100 images. Folders are numbered from 101 to 998. RESET CONTINUOUS E The file number will be reset each time a new memory card is inserted. If the memory card already contains image files, the consecutive file number will be assigned.
Recording Still Images on a Memory Card You can record still images with the camcorder, from a tape in the camcorder. You can also record a still image on the memory card while you record a movie on the tape. PHOTO button Card access indicator TAPE/CARD switch 1. Turn the POWER dial to a recording program and move the TAPE/CARD switch to 2. Press the PHOTO button halfway. . • The symbol turns green once the focus is adjusted.
When the Focus-Priority mode is set to [ON]: When you press the PHOTO button fully before the symbol turns green, it may take up to 2 seconds (4 seconds in the Night recording program) until the focus is adjusted. If the subject is not suitable for autofocus, the camcorder locks the focus. In that case, adjust the focus manually with the focusing ring. When the Focus-Priority mode is set to [OFF]: In step 2, turns green, and focus and exposure are locked.
Capturing a Still Image from a Tape While you are playing back a tape, you can capture the same picture as a still image on the memory card. MENU ( 31) RECORDING SETUP STILL I. REC•OFF 1. Open the menu and select [RECORDING SETUP]. Select [STILL I.REC], set it to [ON] or [ON+CP DATA] and close the menu. 2. While you are playing back the tape, press the PHOTO button.
Selecting the Drive Mode Continuous Shooting High-Speed Continuous AEB (Auto Exposure Bracketing) Single Captures a quick series of still images while you hold the PHOTO button pressed down. For the number of frames per second, refer to the table below. The camcorder records a still image in three different exposures (dark, normal, light in 1/2 EV steps). Records a single still image when you press the PHOTO button. E DRIVE MODE button PHOTO button Changing the Drive Mode 1.
Auto Exposure Bracketing Press the PHOTO button. Three still images in different exposures are recorded to the memory card. Make sure that there is sufficient space on the memory card.
Selecting the Metering Method EVALUATIVE CENT.WEIGHT.AVERAGE SPOT Appropriate for standard shooting conditions, including backlit scenes. The camcorder divides images into several zones for light metering. It evaluates the position and brightness of the subject, background, direct light or backlight, and adjusts the exposure of the main subject accordingly. Averages the light metered from the entire screen, giving more weight to the subject in the center. Meters the area within the spot AE point frame.
Using an Optional Flash You can use E-TTL II compatible Canon Speedlite flashes designed for use with Canon SLR cameras, including the 420EX/430EX/550EX/580EX models, to record natural still images under low light conditions. Refer also to the instruction manual of the Speedlite flash. Connecting a Speedlite Flash When connecting a Canon Speedlite flash you cannot use the Off-Camera Shoe Cord designed for Canon EOS SLR cameras. Always turn off the camcorder when connecting or detaching the flash. 1.
Reviewing a Still Image Right after Recording You can select to display a still image for 2, 4, 6, 8 or 10 seconds after it has been recorded. MENU ( 31) CAMERA SETUP E REVIEW •••••••2SEC Open the menu and select [CAMERA SETUP]. Select [REVIEW], select a setting option and close the menu. A still image is displayed as long as you hold the PHOTO button after recording.
Playing Back Still Images from a Memory Card - button SLIDE SHOW button + button TAPE/CARD switch POWER dial 1. Turn the POWER dial to and move the TAPE/CARD switch to 2. Press the +/– button to move between images. . Images not recorded with this camcorder, uploaded from a computer, edited on a computer and images whose file names have been changed may not be played back correctly.
Index Screen 1. Move the zoom lever toward W. Up to 6 images appear. E 2. Turn the SELECT dial to select an image. • Move the “ ” to the image you wish to view. • You can switch between the index pages by pressing the + / – button. 3. Move the zoom lever toward T. The index screen is cancelled and the selected image is displayed. Card Jump Function You can locate images without displaying them one by one.
Erasing Images You can erase images one at a time or all at once. Be careful when erasing images. Erased images cannot be recovered. Erasing a still image that had a custom preset file embedded (recorded with the [ON+CP DATA] setting) will erase the image and the embedded custom preset file. Protected images cannot be erased. Erasing a Single Image 1. Select the image you wish to erase. 2. Press the SET button to open the still image operations menu.
Protecting Images You can protect important images from accidental erasure when displaying a single image or the index screen. E If a memory card is initialized, all still images, even protected ones, will be erased permanently. 1. Select the image you wish to protect. 2. Press the SET button to open the still image operations menu. In mode, the menu appears when you press the SET button while you are reviewing a still image, or if you press the SET button immediately after recording an image. 3.
Initializing a Memory Card Initialize new memory cards, or when you get the message “CARD ERROR”. You can also initialize a memory card to erase all data recorded on it. Initializing a memory card erases all data, including protected images and custom preset files. Images and custom preset files erased through the card initialization cannot be recovered. If you use a memory card other than the supplied one, initialize it with the camcorder. MENU CARD OPERATIONS INITIALIZE ( 31) 1. 2. 3. 4.
Print Order Settings You can select still images for printing and set the number of copies. These print order settings are compatible with the Digital Print Order Format (DPOF) standards and can be used for printing on DPOF compatible printers. A maximum of 998 still images can be selected. E Selecting Still Images for Printing (Print Order) 1. 2. 3. 4. Select the still image you wish to print. Press the SET button to open the still image operations menu. Select [ PRINT ORDER].
Settings Retained at Power Off or STANDBY Mode Additional Information The following list shows the settings that are retained when you turn the power off or press the STANDBY button. If the built-in lithium button battery has become depleted, all settings will be erased.
The following list shows the settings that are retained when you change the programmed AE mode or frame rate.
Screen Displays Hiding the Displays on the Camcorder Screen You can hide the displays on the screen to have a clear screen for playback. MENU ( 31) DISPLAY SETUP / DISPLAYS•••••ON Open the menu and select [DISPLAY SETUP/ [OFF ] and close the menu. ]. Select [DISPLAYS], set it to • Warning messages still appear, and the data code appears if turned on. • Tape operation displays appear for 2 seconds.
Screen Displays during Recording See also 44.
Screen Displays during Playback Date search ( 107)/ Index search ( 106) Audio output ( 104) Mix balance ( 104) Custom keys ( 90) Data code ( 108) End search ( 49) Recording standard ( 47) Frame rate ( 56) Tape operation ( 98) REC PAUSE STOP EJECT PLAY : Fast forward : Rewind : Fast forward playback/rewind playback : ×2 playback : ×1 playback : Frame advance playback 134 User bit ( 62) Audio level indicator ( 67) Custom preset data embedded with the still image ( Image protected ( 127) Image number ( 115)
Side panel Time code E Video signal standard Time code setting Video output signal from the HD/SD SDI Terminal [AUDIO LEVEL] is set to [MANUAL] Tape has reached the end Remaining battery charge Time code synchronization setting Audio level indicator Additional Information 135
List of Messages Message SET THE TIME ZONE, DATE AND TIME CHANGE THE BATTERY PACK THE TAPE IS SET FOR ERASURE PREVENTION REMOVE THE CASSETTE CHECK THE HDV/DV INPUT CONDENSATION HAS BEEN DETECTED TAPE END HEADS DIRTY, USE CLEANING CASSETTE ENTERING “POWER STANDBY” CHECK THE LENS NO CARD NO IMAGES CARD ERROR CARD FULL NAMING ERROR UNIDENTIFIABLE IMAGE THE CARD IS SET FOR ERASURE PREVENTION INCORRECT TAPE STANDARD PLAYBACK IS RESTRICTED THE MEMORY CARD COVER IS OPEN HD INCOMPATIBLE LENS THIS LENS HAS NO STILL
Maintenance/Others Camcorder Handling Precautions Do not carry the camcorder by the viewfinder, the microphone or its cable. Do not leave the camcorder in places subject to high temperatures, such as a sun-heated car, and high humidity. Do not use the camcorder in places subject to magnetic or electric fields such as near TV sets, plasma TVs, radio transmitters or portable communication devices. Do not point the lens or viewfinder at strong light sources.
Viewfinder 1. Open the protect cover (e.g. using a flathead screwdriver). 2. Clean the glass with a cotton swab. 3. Reattach the protect cover. Be careful not to scratch the glass when cleaning. Video Heads When the message “HEADS DIRTY, USE CLEANING CASSETTE” appears, when the playback picture becomes distorted, or if, when playing back a tape in HDV standard, the picture and/or sound stops momentarily (about 0.5 seconds) the video heads need to be cleaned.
Condensation Moving the camcorder rapidly between hot and cold temperatures may cause condensation (water droplets) to form on its internal surfaces. Stop using the camcorder if condensation is detected. Continued use may damage the camcorder.
Battery Pack Handling Precautions DANGER! Treat the battery pack with care. • Keep it away from fire (or it might explode). • Do not expose the battery pack to temperature higher than 60 ºC (140 ºF). Do not leave it near a heater or inside a car in hot weather. • Do not try to disassemble or modify it. • Do not drop or knock it. • Do not get it wet. Charged battery packs continue to discharge naturally. Therefore, charge them on the day of use, or the day before, to ensure a full charge.
Cassette Handling Precautions Rewind tapes after use. If the tape is lose or damaged, it may cause picture and sound distortion. Return cassettes to their case and store them upright. Rewind tapes from time to time if they are stored for a long time. Do not leave the cassette in the camcorder after use. Do not use spliced tapes or nonstandard cassettes as they may damage the camcorder. Do not use tapes that have been jammed as video heads may become dirty.
Using the Camcorder Abroad Power Sources You can use the compact power adapter to operate the camcorder and to charge battery packs in any country with power supply between 100 and 240 V AC, 50/60 Hz. Consult the Canon Service Center for information on plug adapters for overseas use. Playback on a TV Screen You can only play back your recordings on TVs with NTSC system.
Recycling the Built-in Rechargeable Lithium Battery If you should dispose of your camcorder, first remove the built-in rechargeable lithium battery for recycling according to the recycling system of your country. E 1. Remove the labeled plate shown in the illustration using a flathead screwdriver. 2. Using a pair of cutters or tin snips, cut the 4 indicated plastic joints and remove the cover. 3.
Troubleshooting If you have a problem with your camcorder, refer to this checklist. Consult your dealer or a Canon Service Center if the problem persists. Power Source Problem Camcorder will not turn on. The camcorder switches off by itself. Viewfinder switches on and off. Cause Solution Battery pack is not correctly attached. Attach the battery pack correctly. Power save function has been Turn on the camcorder. activated. Battery pack is exhausted. Replace or charge the battery pack.
Recording Problem A vertical light bar appears on the screen. Viewfinder picture is blurred. Audio is not recorded. Audio is recorded in a very low level. Cause Bright light in a dark scene may cause a vertical light bar (smear) to appear. This is not a malfunction. Viewfinder is not adjusted. Solution Record in the Av mode with F5.6– F8.0. 73 Adjust the viewfinder with the dioptric adjustment lever. The INPUT SELECT switch is not set Set the INPUT SELECT switch to to the correct position.
About the LCD screen The LCD screen is produced with extremely high-precision manufacturing techniques, with more than 99.99% of the pixels operating to specification. Less than 0.01% of the pixels may occasionally misfire or appear as black or green dots. This has no effect on the recorded image and does not constitute a malfunction.
System Diagram (Availability differs from area to area) ZR-1000 Zoom Remote Controller E Speedlite Flash 420EX, 430EX, 550EX, 580 EX WL-D5000 Wireless Controller ZR-2000 Zoom Remote Controller MA-300 Microphone Adapter SBR-1000 Shooting Brace SS-1000 Shoulder Strap FU-1000 Monochrome CRT Viewfinder Unit 3 MiniDV Video Cassette Extender XL 1.6x 1 16x IS II Zoom Lens XL 5.5-88 mm RC-72 Ratio Converter 5 DC-920 DC Coupler 3x Zoom Lens XL 3.4–10.
1 Can be attached to the HD 20x L IS, 20x L IS, 16x IS II and 16x manual zoom lenses (only for recording in SD mode). EF-S lenses cannot be used. 3 When you use the FU-1000 Monochrome CRT Viewfinder with the XL H1 you can use the compact power adapter or the optional CB-920 Car Battery Adapter as the power source. You cannot use the battery adapter supplied with the FU-1000; instead, connect the DC coupler directly to the XL H1 and connect it to the compact power adapter or the car battery adapter.
Optional Accessories Call or visit your local retailer/dealer for genuine Canon video accessories. You can also obtain genuine accessories for your Canon camcorder by calling: 1-800-828-4040, Canon U.S.A. Information Center. E Use of genuine Canon accessories is recommended. This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc.
Extender XL 1.6x Attach this extender between a Canon XL lens and the XL H1 to boost the focal length of the lens by 1.6x. EF Adapter XL This allows you to attach Canon EF lenses to the XL H1. The difference in size between the XL H1’s 1/3-inch CCD’s and 35 mm film means that the effective focal length of still camera lenses is multiplied by 8.8x (4:3)/ 7.2x (16:9). • Consult your local service outlet to make sure there are no compatibility problems with your chosen lens.
CH-910 Dual Battery Charger/Holder The CH-910 can charge two battery packs consecutively. You can also power the camcorder by connecting the CH-910 with charged battery packs to the camcorder. When you attach two battery packs, a battery pack can be exchanged without interrupting the power supply. E Battery Pack Charging Time BP-950G 280 min. BP-970G 380 min. Charging time varies according to the charging condition.
Specifications XL H1 System Video Recording System Audio Recording System Television System Image Sensor Tape Format Tape Speed Maximum Recording Time (60 min.
Input/Output Terminals S-video Terminal Video Terminal HD/SD-SDI Terminal COMPONENT OUT Terminal Audio Out Terminals Audio In Terminals HDV/DV Terminal GENLOCK Terminal TC-IN Terminal TC-OUT Terminal Headphone Terminal LANC Terminal 1 Vp-p/75 ohms (Y signal), 0.286 Vp-p/75 ohms (C signal) RCA jack/BNC jack 1 Vp-p/75 ohms unbalanced BNC jack, output only, 0.
CA-920 Compact Power Adapter Power supply Power consumption Rated output Operating temperature Dimensions Weight 100 – 240 V AC, 50/60 Hz 24 W Adapter: 7.2 V DC, 2.0 A, Charger: 8.4 V DC, 1.5 A 0 – 40 °C (32°– 104 °F) 75 x 99 x 51 mm (3.0 x 3.9 x 2.0 in.) 215 g (7.6 oz.) without power cable BP-950G Battery Pack Battery type Rated voltage Operating temperature Battery capacity Dimensions Weight Rechargeable lithium ion battery 7.4 V DC 0 – 40 °C (32°– 104 °F) 5,200 mAh 38.2 x 40.3 x 70.5 mm (1.5 x 1.
Index A Abroad,using the camcorder . . . . . . . . . . . . . . . . . . . . . . . . 142 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 AE shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Analog-digital converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Aspect guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Aspect ratio . . . . . . . . . . . . . . .
Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 64 Microphone attenuator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Mix balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 N ND filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Night (recording program) . . . . . . . . . . . . . . . . . . . . . . . . . 70 Non-drop frame (time code) . . . . . . . . . . . .
CH 2/4 CH 1/3 Additional Information ADVANCED CH 4 CH 3 PHONES Mic Power CH 2/ CH 4 FRONT 1 : sheeld 2 : hot 3 : cold CH 1/ CH 3 REAR CH1 ON/OFF MIC/LINE Phantom 48V CH2 balance to unbalance Head Amp ATT Head Amp Head Amp Phone Amp Phone Amp Head Amp ATT Head Amp ATT ATT : FRONT ATT SW balance to unbalance Head Amp ATT ATT : REAR ATT SW INPUT SELECT SW INPUT SELECT SW Audio process 1 Input Output PHONE OUT PHONE OUT VOL Pre Amp XLR GAIN UP VOL Pre Amp XLR GAIN UP (me
LCD Driver LEVEL METER CH 3 CH 4 RCA CH 4 RCA CH 3 CVF Display CH 2 PHONE Rch METER Rch RCA CH 2/CH 4 PHONE Lch METER Lch RCA CH 1/CH 3 CH 1 MUTE MUTE CH1 CH2 MUTE CH4 CH3 DELAY normal DELAY Line Out PB Line Out PB normal DELAY Monitor Select ; MENU REC CH SELECT SW CH1 normal Line Out PB CH2 CH4 Line Out PB normal DELAY CH3 CH1 MUTE Audio Monitor MIX MIX Audio Monitor Monitor Select ; MENU HD SD HD SD MPEG AUDIO ENC to Tape/1394 MPEG AUDIO DEC from Ta
Custom Keys Make a copy of this page and carry it with you as a reminder of the functions that can be assigned to each of the two custom keys in each operation mode. E You can assign frequently used functions to the custom keys. The custom keys can have different functions assigned to them in each of the different operation modes.
U.S.A. CANON CONSUMER DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY FOR THE UNITED STATES The warranty set forward below is given by Canon U.S.A., Inc. with respect to equipment purchased in the United States. The limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase.
CANON INC. U.S.A. CANON U.S.A., INC. NEW JERSEY OFFICE 100 Jamesburg Road, Jamesburg, NJ 08831 USA CANON U.S.A., INC. CHICAGO OFFICE 100 Park Blvd., Itasca, IL 60143 USA CANON U.S.A., INC. LOS ANGELES OFFICE 15955 Alton Parkway, Irvine, CA 92618 USA CANON U.S.A., INC. HONOLULU OFFICE 210 Ward Avenue, Suite 200, Honolulu, HI 96814 USA z If you have any questions, call the Canon U.S.A. Information Center toll-free at 1-800-828-4040 (U.S.A. only). CANADA CANON CANADA INC.
