PUB.
Important Usage Instructions Introduction WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. CAUTION: DISCONNECT THE MAINS PLUG FROM THE SUPPLY SOCKET WHEN NOT IN USE.
The XL H1S / XL H1A - A Broad Range of Capabilities Ultimate HD Quality New and improved lens The HD 20x L IS III is the latest addition to the XL line of high-end interchangeable lenses and now features a built-in iris ring for improved operability. 3CCD system By using three 1/3-in. CCDs (each with a total of 1.67 mega pixels and 1,440x1,080 effective pixels), the camcorder offers a horizontal resolution of 800 TV lines, the highest in HDV standard.
About this Manual Thank you for purchasing the Canon XL H1S / XL H1A. Please read this manual carefully before you use the camcorder and retain it for future reference. Should your camcorder fail to operate correctly, refer to Troubleshooting ( 146). Conventions Used in this Manual : Precautions related to the camcorder’s operation. : Additional topics that complement the basic operating procedures. : Reference page number.
About the HD/HDV and SD/DV Specifications In the manual, a distinction is made between video signal standards (camera section) and recording standards (recorder section). The video signal can be set to HD (high definition) or SD (standard definition) specifications; the recording standard on the tape will be HDV or DV, respectively.
Contents Introduction The XL H1S / XL H1A - A Broad Range of Capabilities .................................................................................... 3 About this Manual ............................................................................................................................................. 4 Checking the Supplied Accessories ................................................................................................................. 8 Components Guide .....................
External Connections Video Signal Output Standards ....................................................................................................................... 80 Connecting to a Monitor/TV ............................................................................................................................ 81 Audio Output ...................................................................................................................................................
Checking the Supplied Accessories CA-920 Compact Power Adapter DC-920 DC Coupler BP-950G Battery Pack WL-D5000 Wireless Controller SDC-32M SD Memory Card HDVM-E63PR Digital Videocassette Color Viewfinder Unit 2 x AA (R6) Batteries (for the wireless controller) Microphone Unit Stereo Cable DTC-1000 Component Video Cable External Monitor Cable Adjustment Band (for the external microphone holder) Adapter Holder Unit Tripod Adapter Base SS-1100 Shoulder Strap Camcorder Dust Cap Canon HD Video L
Components Guide Left side view dial External control mode* VCR/PLAY mode Power off Manual Auto Shutter-Priority Aperture-Priority Recording Spotlight programs Night Easy Recording * Reserved mode for future software development.
Left side view Viewfinder unit/Microphone unit HD 20x L IS III lens Eye cup ( 20) Dioptric adjustment lever ( 21) Color viewfinder ( 19-22) STEREO/MONO microphone selector ( Lock screw ( 21) Viewfinder cable ( 19) Lock release button ( 22) Iris ring ( 61, 64) Zoom ring ( 40) Lens hood ( 26) 10 54) Focus ring ( 42) RESET button ( 146) Memory card slot ( 30) ND filter operating ring ( 47) ND filter unlock button ( 47) STABILIZER ON/OFF switch ( 57) POSITION PRESET switch ( 41) AF switch ( 42)/ POSITION P
Right side view Introduction S-video terminal ( 84) VIDEO OUT terminal (BNC) ( 84) VIDEO IN/OUT terminal (RCA) ( 84) OUT terminals (CH1/CH2, RCA) ( 86) IN terminals (CH1/CH2, RCA) ( 54) Terminal cover Battery attachment unit ( 15) BATT.
Front view Back view Tally lamp ( 105) Remote sensor ( 28, 114) Grip belt ( 23) Attachment sockets for the optional TA-100 Tripod Adapter ( 151) or the supplied tripod adapter base Tripod socket Viewfinder cable ( 19) Remote sensor ( 28, 114) START/STOP button ( 34) Microphone lock screw ( 23) Strap mount ( 23) INPUT terminals (CH1/CH2, XLR) ( 54) SHUTTER buttons ( 61, 63) , PHONES LEVEL dial (headphone) terminal HDV indicator ( 38) HDV/DV terminal ( 83, 89, 91) terminal switches (CH1,CH2) ( 54) switche
Top view Introduction PHOTO button ( 117) / MAGN.
WL-D5000 Wireless Controller PHOTO button ( 117) START/STOP button ( 34) MENU button ( 31) TV SCREEN button ( 76) SLIDESHOW button ( 123) DATA CODE button ( 113) INDEX WRITE button ( 76) AUDIO MONITOR button ( 86) END SEARCH button ( 39) SEARCH SELECT button ( 112, 113) REC PAUSE button ( 89) REW button ( 110) ZERO SET MEMORY button ( 112) button ( 110) PAUSE button ( 110) 14 REMOTE SET button ( 114) AV DV button ( 90) Zoom buttons ( 40) Menu selection buttons ( 31) SET button ( 31) CARD – button ( 123)
Preparing the Power Supply Preparations Charging the Battery Pack Disconnect the DC coupler from the compact power adapter before charging. Remove the terminal cover of the battery pack. 1. Connect the power cord to the compact power adapter. 2. Plug the power cord into a power outlet. 3. Attach the battery pack to the compact power adapter. • Press lightly and slide the battery pack in the direction of the arrow until it clicks. • The charge indicator starts flashing.
Using a Household Power Outlet 1. Turn the dial to OFF. 2. Attach the DC coupler to the camcorder. Press lightly and slide the DC coupler up, in the direction of the arrow until it clicks. 3. Connect the power cord to the compact power adapter. 4. Plug the power cord into a power outlet. 5. Connect the DC coupler to the compact power adapter. 6. Detach the DC coupler after use. Holding the BATT. RELEASE button pressed down, slide the DC coupler down to remove it. BATT.
Charging, Recording and Playback Times The following times are approximate and vary according to the charging, recording and playback conditions. Battery Pack BP-930 BP-945 BP-950G BP-970G Charging time with the CA-920 Compact Power Adapter 145 min. 220 min. 235 min. 320 min. Supplied color viewfinder 130 min. 195 min. 275 min. 375 min. FU-1000 monochrome viewfinder2 100 min. 155 min. 215 min. 295 min.
Battery Pack BP-930 BP-945 BP-950G BP-970G HDV Maximum Recording Time HD 20x L IS III Lens Supplied color viewfinder 140 min. 205 min. 290 min. 400 min. HD 20x L IS II Lens FU-1000 monochrome viewfinder2 Supplied color viewfinder 105 min. 140 min. 160 min. 210 min. 230 min. 295 min. 310 min. 405 min. FU-1000 monochrome viewfinder2 105 min. 165 min. 230 min. 315 min. Supplied color viewfinder 145 min. 215 min. 305 min. 420 min.
Preparing the Camcorder Attaching and Detaching the Color Viewfinder Unit Attaching the Color Viewfinder Unit 1. Slide the viewfinder unit onto the bracket and tighten the lock screw. 2. Connect the viewfinder cable to the EVF1 socket on the camcorder. Insert the cable plug straight into the camcorder’s socket. 3. Hook the viewfinder cable onto the cable clamp. Preparations To use the optional FU-1000 Monochrome CRT Viewfinder Unit, connect it to the EVF2 socket on the camcorder instead.
Attaching and Detaching the Eye Cup You can change the position of the eye cup for use with either the left or right eye. Detach the eye cup and reattach it when changing the position of the eye cup for right or left eye use. Attaching the Eye Cup Align the hole for the dioptric adjustment lever with the lever, and pull the eye cup into position. Right eye use Detaching the Eye Cup Detach the eye cup as shown in the illustration.
Adjusting the Position of the Viewfinder The viewfinder position can be changed (right/left, forward/backward). When storing the camcorder in the optional HC-3200 System Case, adjust the viewfinder to the right and lock it. Right/Left Adjustment Loosen the top lock screw, adjust the viewfinder to the right/left and tighten the screw. Forward/Backward Adjustment Loosen the bottom lock screw, adjust the viewfinder forward/backward and tighten the screw.
Adjusting the Viewfinder You can adjust the brightness, contrast, color and sharpness of the viewfinder. These adjustments will not affect your recordings. MENU ( 31) DISPLAY SETUP / EVF SETUP EVF BW MODE•••OFF BRIGHTNESS•••0 CONTRAST•••••0 COLOR••••••••0 SHARPNESS••••2 1. Press the MENU button. 2. Turn the SELECT dial to select [DISPLAY SETUP/ ] and press the SET button. 3. Select [EVF SETUP] and then select [BRIGHTNESS], [CONTRAST], [COLOR] or [SHARPNESS]. 4.
Attaching the Microphone Unit 1. Loosen the microphone lock screw on the viewfinder unit, open the microphone holder and insert the microphone. 2. Align the mark on the microphone with the mark on the microphone holder and tighten the lock screw. 3. Plug the microphone cable to the camcorder’s FRONT MIC terminals.
Attaching the Adapter Holder Attach the adapter holder to use the optional CH-910 Dual Battery Charger/Holder or a commercially available wireless microphone receiver. 1. Attach the adapter holder and secure it by tightening the screws. 2. Adjust the position of the support bars. Support bars When using the optional CH-910, hook it onto the support bars and secure it with the stop lever. To detach the CH-910, press the stop lever in the direction of the arrow and pull the CH-910 off the support bars.
Preparing the Lens Refer also to the instruction manual of the lens. Mounting the Lens 1. Set the dial to OFF. 2. Remove the dust caps from the camcorder and the lens. 3. Align the red mark on the lens with the red mark on the camcorder and turn the lens clockwise until it clicks. Removing the Lens Preparations 1. Set the dial to OFF. 2. Slide the LENS RELEASE switch all the way in the direction of the arrow. 3. Turn the lens counter-clockwise until it stops and remove the lens. 4.
Proper operation cannot be guaranteed when recording in HDV standard with the optional Extender XL 1.6x. The message “HD INCOMPATIBLE LENS” will appear when using the extender, even with an HD-compatible lens. Attaching the Lens Hood Attach the lens hood to protect the lens and shade it from stray light. 1. Place the lens hood on the front of the lens and screw it clockwise until the Canon logo appears on top. • Be careful not to deform the lens hood.
AF Adjustment 1. 2. 3. 4. 5. Press the MENU button. Turn the SELECT dial to select [CAMERA SETUP] and press the SET button. Select [FB] and then select [ AF ADJUST]. When the confirmation screen appears, press the SET button to begin the adjustment. Once the message “FB ADJUSTMENT SUCCESSFUL” is displayed, press the MENU button to close the menu. MF Adjustment 1. 2. 3. 4. 5. Press the MENU button. Turn the SELECT dial to select [CAMERA SETUP] and press the SET button.
Using the Wireless Controller When you press the buttons on the wireless controller, point it at one of the camcorder’s remote sensors. The camcorder has 3 remote sensors: 2 at the front and 1 at the back. Inserting the Batteries The wireless controller operates with two AA (R6) batteries. 1. Open the battery cover. 2. Insert the batteries following the + and – markings. 3. Close the battery cover. The camcorder and wireless controller are equipped with 2 remote sensor modes ( 114).
Loading/Removing a Cassette Use only videocassettes marked with the videocassettes designed for HDV recording. logo. For recording in HDV we recommend you use 1. Slide the EJECT switch to open the cassette compartment cover. The cassette compartment opens automatically. 2. Load/remove the cassette. • Insert the cassette straight, fully into the compartment with the window facing out. • Remove the cassette by pulling it straight out. Preparations 3. Close the cassette compartment cover. Press the cover.
Inserting/Removing a Memory Card You can use SDHC (SD High Capacity) memory cards, (MMC) with this camcorder. SD memory cards or MultiMedia Cards Inserting the Card 1. Set the dial to OFF. 2. Push the switch in the direction of the arrow to open the memory card slot cover. 3. Insert the memory card straight, all the way into the memory card slot. 4. Close the memory card slot cover. Do not force the cover closed if the card is not correctly inserted.
Changing Settings with the MENU Button Many of the camcorder’s functions can be changed from the on-screen menu. Selecting Menus and Settings 1. Press the MENU button to open the menu. 2. Turn the SELECT dial to select a submenu and press the SET button. 3. Turn the SELECT dial to select a menu item and press the SET button 4. Turn the SELECT dial to select a setting option and press the SET button. 5. Press the MENU button to close the menu.
Date/Time and Language Settings Set the time zone, date and time when you first start using your camcorder, or if the built-in rechargeable battery has discharged completely. Setting the Time Zone/Daylight Saving Time MENU ( 31) SYSTEM SETUP/ D/TIME SET T.ZONE/DST•••PARIS 1. Press the MENU button. 2. Turn the SELECT dial to select [SYSTEM SETUP/ ] and press the SET button. 3. Select [D/TIME SET ] and then select [T.ZONE/DST] and press the SET button. The time zone setting appears.
Changing the Date Format You can select between three date formats: [JAN. 1, 2008], [1. JAN. 2008] and [2008. 1. 1]. MENU ( 31) SYSTEM SETUP/ D/TIME SET DATE FORMAT •• 1.JAN.2008 Open the menu and select [SYSTEM SETUP/ ]. Select the [D/TIME SET ] submenu and then select [DATE FORMAT]. Select a date format and close the menu. Changing the Display Language The default language for displays and menu items is English.
Recording Recording Before You Begin Recording Make a test recording first to check if the camcorder operates correctly. If necessary, clean the video heads ( 144). The default recording standard is HDV. About the audio recording, refer to the relevant chapter ( 53). Recording 1. Remove the lens cap. 2. Press the lock button and set the dial to a recording program. 3. Press the Start/Stop button to begin recording. • The red REC indicator on the viewfinder and the tally lamps light up.
Low-angle Recording The carrying handle is equipped with a duplicate set of recording and zoom controls, ideal for low-angle recording. Slide the LOCK switch in the direction of the arrow to prevent the accidental operation of these controls. LOCK switch Zoom lever Power Saving Mechanisms STANDBY Button Press the STANDBY button and hold it pressed down for more than 1 second in record pause or VCR stop mode to enter the standby mode.
Screen Displays while Recording Time code Indicates the recording time in hours, minutes, seconds and frames. Remaining tape Indicates the remaining time on the tape in minutes. “ END” will appear when the tape reaches the end. • When the time left is less than 15 seconds, the remaining tape time may not appear. • Depending on the type of tape, the remaining time displayed may not be accurate.
Selecting the On-Screen Displays You can select the amount of information shown on the screen from full, partial or no display. Repeatedly pressing the EVF DISPLAY button will cycle through the options in the following sequence. Level 11: All screen displays Level 2: Customized displays ( 106), date/time2 Level 33: Markers, safety zone guides, date/time2 Level 4: No displays 1 This level cannot be selected if [SYSTEM SETUP/ ] [ALL DISPLAY] is set to [DISABLE].
Selecting the Signal Standard and Aspect Ratio You can select the signal standard of your recording (high definition or standard definition) and, for standard definition recordings, also the aspect ratio of the recording. Since the camcorder’s screen has an aspect ratio of 16:9, when you set the MODE SELECT switch to SD 4:3 the picture will appear in the center of the screen with black sidebars. Change the position of the MODE SELECT switch.
Locating the End of the Last Scene You can use this function to locate the end of the last recorded scene. Press the END SEARCH button. • appears. • The camcorder rewinds/fast forwards the tape, plays back the last few seconds of the recording and stops the tape. • Pressing the button again cancels the search. The end search function cannot be used once you remove the cassette.
Zooming You can operate the zoom using the zoom lever on the side grip or the one on the carrying handle. You can also use the zoom ring on the lens or the zoom buttons on the wireless controller. With the customized functions ( 100) you can change the direction and response sensitivity of adjustment when the zoom ring is used, change the zoom speed and select the zoom indicator (graphic or numeric). Zoom buttons Zoom lever Zoom ring Move the zoom lever toward W to zoom out (wide-angle).
Zoom buttons on the carrying handle: The zoom speed is constant and can be set to one of 16 zoom speed levels. Set the ZOOM SPEED switch to CONSTANT and change the zoom speed level as described previously. Zoom buttons on the supplied wireless controller: The zoom speed is constant and cannot be adjusted. When a fixed focal length lens is used, no zoom–related indications will appear on screen. Zoom Preset (lenses with zoom preset function) This function enables any given zoom position to be memorized.
Adjusting the Focus Functions in this chapter are explained using the HD 20x L IS III lens. If you are using a different lens, refer also to the instruction manual of the lens. The camcorder can be set to Autofocus or Manual Focus. Autofocus In addition to the usual autofocus, the camcorder has also a Push-AF function to allow for temporary autofocus while focusing manually.
Autofocus may not work well on the following subjects. In that case, focus manually. - Reflective surfaces - Subjects with low contrast or without vertical lines - Fast moving subjects - Through dirty or wet windows - Night scenes Manual focus 1. When using a lens with autofocus function, set the focus mode switch to M. • “MF” appears. • When a lens without autofocus function is used, “MF” will not appear. Focus ring 2. Zoom in to telephoto. 3. Turn the focus ring to adjust the focus.
Using the Focus Assist Functions (Peaking and Magnifying) In order to make manual focusing easier, you can use two assist functions: Peaking emphasizes the outlines of the subject creating a clearer contrast, and Magnifying enlarges the image on the screen. You can also combine both for greater effect. With the custom function [F.AST BW-MOD] ( 100) you can set the display to change automatically to black & white while using the focus assist functions.
Focus Preset (lenses with focus preset function) This function enables a focus position to be memorized. Later, you can return to the preset focus position instantly. You can also select the speed at which the camcorder returns to the preset focus position. Focus ring Presetting the Focus 1. Set the focus mode switch to M. “MF” appears. 2. Set the POSITION PRESET switch to FOCUS. The focus preset speed currently selected appears. Recording 3. Adjust the focus with the focus ring. 4.
Macro Shooting (Focus Limit) Usually the camcorder’s focus range allows macro shooting. You can activate the focus limit to restrict the focus range. Using the HD 20x L IS III lens, the focus range 10 cm (at full wide-angle) is limited to 1 m (throughout the entire zoom range). MENU ( 31) CAMERA SETUP FOCUS LIMIT•••OFF Open the menu and select [CAMERA SETUP]. Select [FOCUS LIMIT], set it to [ON and close the menu. appears. The focus limit will be canceled in the following cases.
Using the ND Filter (lenses with built-in ND filter) When recording in bright surroundings, the camcorder will set a small aperture value and the picture may appear blurred. When using a lens with a built-in ND filter, turn the ND filter on/off according to the screen display. ND filter unlock button ND filter operating ring With the HD 20x L IS III lens: Press the ND filter unlock button and turn the ND filter operating ring.
Selecting the Frame Rate You can set the frame rate to 50i or 25F, regardless of the recording mode. 50i Mode Records 50 interlaced fields per second, the same as standard-definition TV signals. 25F Mode HD Records 25 frames per second according to HDV native 1080/25p specifications. For playback, the signal is converted to 50i but video output from the HDV/DV terminal will be 25p.
Setting the Time Code You can select the running mode of the camcorder’s time code. You can enter the initial value for the [FREE-RUN] and the [REC-RUN PS.] settings. [REC-RUN]: The time code runs only when recording. [REC-RUN PS.]: The time code runs only when recording, starting from a preset value. [FREE-RUN]: MENU ( 31) The time code runs regardless of the operation of the camcorder. SIGNAL SETUP TIME CODE COUNT-UP•••••REC-RUN 1. Open the menu and select [SIGNAL SETUP].
Synchronizing the Camcorder’s Time Code You can synchronize this camcorder’s time code to an external time code generator. You can also include in the recording the user bit signal received from the TC-IN terminal ( 52). The camcorder offers the following synchronization options. Genlock When a reference sync signal (analog blackburst or tri-level signal) is input through the GENLOCK terminal, the V and H phases of the camcorder’s time code will automatically be synchronized to it.
When an external time code signal is received, the camcorder's own time code will be synchronized to it and the synchronization will be maintained even if you disconnect the cable from the TC-IN terminal. However, performing any of the following actions while the cable is not connected will cause the time code to lag slightly; the correct time code will be restored once you reconnect the cable. - Turning the camcorder off/on. - Changing the position of the dial to or from .
Setting the User Bit The user bit display can be selected from the date or the time of recording, or an identification code consisting of 8 characters in the hexadecimal system that is useful for labeling tapes. There are sixteen possible characters: the numbers 0 to 9 and the letters A to F. If user bit information is being received along with an external time code, you can also record the external user bit on the tape. MENU ( 31) RECORDING SETUP UB SELECT•••00 00 00 00 1.
Audio Recording When recording on the tape in either HDV or DV standard, audio is recorded on two channels. HDV The audio transfer rate is 384 kbps and the sampling frequency is 48 kHz. DV You can record audio in 16-bit mode (sampling frequency 48 kHz), or 12-bit mode (sampling frequency 32 kHz). • Audio is recorded on channels 1 and 2, leaving the other channels unused. • Audio cannot be dubbed using this camcorder.
Recording Audio Select the audio input from FRONT (supplied microphone), XLR MIC (XLR terminals) or XLR LINE (XLR terminals). You can select the audio input independently for channel 1 and channel 2. Using the Front Microphone Set the INPUT SELECT switch to FRONT MIC. • You can select the microphone setting with the STEREO/MONO switch on the microphone itself. In the MONO position, the same monaural audio signal will be recorded on channels 1 and 2. Using the XLR terminals 1.
Adjusting the Audio Recording Level If the audio level is too high and the sound sounds distorted, activate the microphone attenuator (20 dB), by setting the FRONT MIC ATT. switch or the corresponding switch to ATT. Hiding/Displaying the Audio Level Indicator MENU ( 31) DISPLAY SETUP/ AUDIO LEVEL••ON Open the menu and select [DISPLAY SETUP/ option and close the menu. ]. Select [AUDIO LEVEL], select a setting The audio level indicator can also be turned on/off with a custom key ( 75).
You can select to synchronize the audio signal with the video signal by adding an equal amount of delay to the audio. Open the menu and select [AUDIO SETUP]. Select [MONITOR SEL.], set it to [LINE OUT] and close the menu. If you wish to monitor audio in real time, select [NORMAL] instead. With either setting, the audio and video signals recorded on the tape will be synchronized. You can activate the audio peak limiter to prevent audio distortions.
Image Stabilizer (lenses with image stabilization function) You can select to activate the image stabilizer or turn it off depending on the recording conditions. To turn off the image stabilizer using the HD 20x L IS III lens: Set the STABILIZER ON/OFF switch to OFF. The image stabilizer cannot be turned off in Recording mode. Easy We recommend turning off the image stabilizer when the camcorder is mounted on a tripod.
Using the Programmed AE Modes Programmed auto exposure modes provide advanced automated recording techniques ensuring professional results in various shooting conditions. Manual ( 61) This mode offers the creative freedom of a complete range of manual controls. In Manual mode, you have the option to set the exposure at any combination of shutter speed and aperture levels. Auto Like the Easy Recording mode, the camcorder automatically controls camera adjustments allowing you to simply point and film.
Easy Recording The camcorder automatically controls the focus, shutter speed, aperture, gain, white balance, and AE Shift allowing you to simply point and film. This mode locks all of these features and options, making them fixed and unadjustable. Selecting the Programmed AE Modes Press the lock button and turn the dial. dial The symbol of the selected mode appears. Do not change the position of the dial while recording as the brightness of the image may change abruptly.
Available lens functions by programmed AE mode1 All other modes Focus ring Zoom ring Iris ring Image stabilizer2 ND filter Focus mode selection XAF switch (Push-AF) 1 2 See previous table – (ON) – (AF) – HD 20x L IS III, HD 20x L IS II, HD 6x L, 20x L IS and 16x IS II lenses. Not available with the HD 6x L lens.
Recording in Manual Mode You can set the exposure at any combination of shutter speed and aperture. The aperture value can be adjusted in 1/16 EV stops; however, the aperture value displayed on the screen will change only in 1/4 EV stops.
Push AE In M Manual mode you can use the Push AE function when you want the camcorder to re-establish optimal exposure settings by automatically adjusting the aperture and gain (if the GAIN dial is set to A). Press the PUSH AE button and hold it pressed down. • The camcorder will adjust the aperture value and gain to achieve optimal exposure ( mark above the exposure indicator).
Recording in Shutter-Priority (Tv) Mode Available shutter speeds when recording movies: 1/3*, 1/6, 1/12, 1/25, 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/8000, 1/16000, CS (clear scan) Available shutter speeds when recording still images: 1/3*, 1/6, 1/12, 1/25, 1/50, 1/120, 1/250, 1/500 * Only with the HD 20x L IS II or HD 20x L IS III Lens. 1. Set the dial to Tv. 2. Select the shutter speed with the SHUTTER or button. With the custom function [OPER.
Recording in Aperture-Priority (Av) Mode The aperture value can be adjusted in 1/16 EV stops; however, the aperture value displayed on the screen will change only in 1/4 EV stops. Available aperture values (with the HD 20x L IS II or HD 20x L IS III lens) F1.6, F1.8, F2.0, F2.2, F2.4, F2.6, F2.8, F3.2, F3.4, F3.7, F4.0, F4.4, F4.8, F5.2, F5.6, F6.2, F6.7, F7.3, F8.0, F8.7, F9.
Adjusting the Exposure Exposure Lock 1. Set the dial to , Tv or Av. 2. Press the EXP. LOCK button. • The exposure indicator appears. Use the exposure indicator as an estimate. • The mark above the indicator indicates the standard exposure (calculated by the camcorder). The mark of the indicator indicates the current exposure level within ± 2 EV stops of the standard exposure (beyond 2 stops, the marker will blink). • You can use the custom keys ( 75) or the [SYSTEM SETUP/ ] [E.LCK B.
Gain The gain control adjusts the level of the video signal generated depending on the lighting and shooting conditions. Select automatic gain control, one of the preset gain level ranging from -3 dB to +18 dB or fine-tune the gain level in 0.5 dB increments. GAIN dial A -3 0 +3, +6, +12, +18 0 – +18, +36 Use Automatic gain control. For the lowest noise recording for indoor, low light or low contrast scenes. For lifelike night scenes or scenes under artificial lighting.
White Balance The camcorder uses an electronic white balance process to calibrate the picture for accurate color display under different lighting conditions. In addition to the fully automated mode, white balance modes include an indoor mode, an outdoor mode, a color temperature setting and two user-defined custom preset values. WHITE BALANCE dial AWB (outdoor) (indoor) (color temperature) Custom Preset A, B Use Automatic adjustment of white balance. Bright sunlight (5,600 K). Incandescent light (3,200 K).
Setting a Custom White Balance 1. 2. 3. 4. Set the POWER dial to a recording program other than . Press the WHITE BALANCE dial so that it pops out. Set the WHITE BALANCE dial to one of the custom preset positions, A or B. Point the camcorder at a white object and zoom in until it fills the whole screen. Keep the camcorder zoomed at the white object until step 5 is completed. 5. Press the WHITE BALANCE button. and the corresponding letter will stop flashing and stay on when the setting is completed.
Zebra Pattern This camcorder has a zebra pattern feature that shows black and white diagonal stripes over the areas that are overexposed. The zebra pattern is only displayed on the screen and will not affect your recordings. The zebra pattern will not be displayed while the Peaking function is activated ( 44). Available zebra pattern settings: 70 IRE, 75 IRE, 80 IRE, 85 IRE, 90 IRE, 95 IRE, and 100 IRE.
Color Correction With the color correction function you can set the camcorder to detect the characteristics of a certain color or pattern (color phase, chroma, area and Y level) and correct them automatically when recording. You can set the color correction for up to two different colors (A and B). When determining the color to be corrected, targeted areas will be identified on the screen by zebra pattern alternating with the normal picture.
Activating the Color Correction MENU ( 31) CAMERA SETUP COLOR CORR. CORRECT•••••••OFF 1. Open the menu and select [CAMERA SETUP] and select the [COLOR CORR.] submenu. 2. Select [CORRECT], select a correction mode and close the menu. • You can correct only the predefined A area, only the predefined B area or both. • appears.
Skin Detail Function With the skin detail function you can set the camcorder to detect the characteristics of a certain color or tone. Detail in the targeted areas will be softened in order to conceal skin imperfections. Targeted areas will be identified on the screen by a zebra pattern alternating with the normal picture. On a connected monitor or computer, targeted areas will be identified by white areas alternating with the normal picture.
Selective Noise Reduction With the selective noise reduction function you can set the camcorder to detect the characteristics of a certain color or tone and automatically reduce noise in the targeted areas. This is particularly useful for chroma keying, as targeting the selective noise reduction to the color of the background green or blue screen will result in a smoother composite picture. Targeted areas will be identified on the screen by a zebra pattern alternating with the normal picture.
Clear Scan This feature allows you to record a computer’s CRT screen or other equipment without displaying black band or flicker on the screen. You can adjust the frequency from 50.2 Hz to 200.3 Hz. MENU ( 31) CAMERA SETUP CLEAR SCAN•••50.2Hz 1. Set the dial to Tv or M. 2. Repeatedly press the SHUTTER button to set the shutter speed to “CS”. 3. Open the menu and select [CAMERA SETUP]. Select [CLEAR SCAN], adjust the frequency and close the menu.
Custom Keys You can assign frequently used functions to the custom keys. The custom keys can have different functions assigned to them in each of the operating modes. Default settings: CUSTOM KEY 1 CUSTOM KEY 2 TIME CODE INDEX WRITE TV SCREEN DATA CODE To check the current custom key settings: In a recording mode: Open the menu and select [DISPLAY SETUP/ menu. In a playback mode: Open the menu and select [DISPLAY SETUP/ ZEBRA TV SCREEN TV SCREEN EVF BW MODE ].
Changing the Custom Keys Setting MENU ( 31) SYSTEM SETUP/ * Default value in CUSTOM KEY 1•TIME CODE* mode. Open the menu and select [SYSTEM SETUP/ ]. Select [CUSTOM KEY 1] or [CUSTOM KEY 2], select the function you wish to assign to the custom key and close the menu. When you do not wish to use the custom keys, select [(NONE)]. Activating the Functions with the Custom Key [TIME CODE] Time Code ( 49) Press the CUSTOM KEY (1 or 2) button. The time code setting menu appears.
[TC HOLD] Time Code Hold You can press the custom key button to freeze the display of the time code. The time code will continue running normally even while the time code display is on hold. Time code hold can only be operated with the custom keys. Press the CUSTOM KEY (1 or 2) button. • Pressing the custom key button again will reactivate the normal display of the time code. • While on hold, the time code will be displayed with an H next to it and “HOLD” will appear on the side panel.
[CP BKWD KEY] Custom Preset Backward Key Press the CUSTOM KEY 2 button. Usually, pressing the CUSTOM PRESET SELECT button will cycle forwards to the following custom preset file. Pressing the custom key button instead will cycle backwards to the preceding custom preset file. CP backward key can only be operated with the custom keys. [FB] Flange Back Adjustment Press the CUSTOM KEY (1 or 2) button. The flange back adjustment menu appears.
Color Bars/Audio Reference Signal You can generate and record color bars signals and a 1 kHz audio reference signal. With the customized functions ( 100) you can choose between EBU ([TYPE 1]) and SMPTE color bars ([TYPE 2]) and you can also select the strength of the audio signal (-12 dB, -18 dB, or -20 dB). 1. Select the standard of the color bars signal [COLOR BARS] and the strength of the audio reference signal [1kHz TONE] with the customized functions ( 100). 2.
External Connections Video Signal Output Standards The standard of the video signal output from the HD/SD SDI ( only), COMPONENT OUT and HDV/DV terminals depends on the standard used for recording (or the standard of the recording on the tape being played back) and on various menu settings. Video output from the VIDEO OUT or IN/OUT (S-Video) terminal will always be in 576/50i standard.
Connecting to a Monitor/TV The different recording modes and the corresponding output terminals are given in the table below: COMPONENT OUT Terminal D3 (1440x1080) HDV/DV Terminal MPEG TS [LETTERBOX] SD SDI set to [ON] D1 (SD) MPEG TS [LETTERBOX] 640x480 set to [OFF] D1 (SD) DV (SD) [LETTERBOX] SD SDI set to [ON] D1 (SD) DV (SD) D1 (SD) Normal DV (SD) HD/SD SDI Terminal* HD SD 16:9 [LETTERBOX] 1920x1080 set to [OFF] SD 4:3 * 640x480 VIDEO and Terminals only.
Connection to a High Definition Monitor or HDTV Using the HD/SD SDI Terminal 1 INPUT White VIDEO White Red Stereo Cable* (supplied) L AUDIO Red R Signal flow S (S1)-VIDEO Open the terminal cover BNC Cable (commercially available) Signal flow * If [SDI OUTPUT] is set to [OFF] (no embedded audio), the audio signal is separate from the SDI video output signal Activate the HD/SD SDI output and select the appropriate video output option (HD or SD). 1. Set the dial to . 2.
2 Using the COMPONENT OUT Terminal Open the terminal cover INPUT White VIDEO White Stereo Cable* (supplied) Red L AUDIO Red R Signal flow S (S1)-VIDEO Green Y Blue Pb Red Pr DTC-1000 Component Video Cable (supplied) Signal flow * The audio signal is separate from the component video signal Select the appropriate component video signal depending on the TV or monitor you connect. Open the menu and select [SIGNAL SETUP]. Select [COMP.OUT], select a setting option and close the menu.
4 Using the VIDEO IN/OUT or (S-Video) IN/OUT Terminal Open the terminal cover INPUT VIDEO White White Stereo Cable (supplied) Signal flow Red S-Video Cable* (commercially available) L AUDIO Red R S (S1)-VIDEO * To use the VIDEO terminals instead of the terminal, connect the TV to the camcorder’s VIDEO OUT terminal using a BNC cable (commercially available), or connect the TV to the camcorder’s VIDEO IN/OUT terminal using an RCA video cable (commercially available).
3 Using the SCART Adapter SCART adapter (commercially available) Signal flow RCA cable (commercially available) White Yellow AUDIO AUDIO VIDEO (R) (L/MONO) Red Stereo Cable (supplied) • If connecting to a TV set with a 4:3 aspect ratio, change the [LETTERBOX] setting appropriately. Open the menu and select [SIGNAL SETUP]. Select [LETTERBOX], set it to [ON] and close the menu. 85 External Connections We recommend powering the camcorder from a household power outlet.
Audio Output Selecting the Audio Channel You can select the channel for audio signal output from the terminals. CH1/CH2 and the (headphone) Repeatedly press the AUDIO OUTPUT CH button to change the audio channel. • Pressing the button will cycle between the audio channels in the following order: CH1/CH2 CH1/CH1 CH2/CH2 ALL CH/ALL CH CH1/CH2.
Audio Output Selected CH1/CH2 CH3/CH4 CH1·3/CH2·4 Audio Recordings on 2 Channels Left Output: L or CH1 Right Output: R or CH2 Audio Monitor [AUD.M.SET] CH 1/2 CH 3/4 MIX/FIXED MIX/VAR. CH1/CH1 CH3/CH3 CH1·3/CH1·3 Left Output: L or CH1 Right Output: L or CH1 CH 1/2 CH 3/4 MIX/FIXED MIX/VAR. CH2/CH2 CH4/CH4 CH2·4/CH2·4 Left Output: R or CH2 Right Output: R or CH2 CH 1/2 CH 3/4 MIX/FIXED MIX/VAR. ALL CH/ALL CH Left Output: All channels Right Output: All channels CH 1/2 CH 3/4 MIX/FIXED MIX/VAR.
Digital Video Control This feature enables the camcorder to control the record and stop functions of an external digital device connected to the camcorder through the HDV/DV terminal. The device must comply with the IEEE1394 AV/C protocol. Use the optional CV-250F (4 pin-6 pin) DV cable or a commercially available 6 pin-6 pin DV cable to connect the external device. MENU ( 31) SYSTEM SETUP/ DV CONTROL•••OFF 1. Open the menu and select [SYSTEM SETUP/ ].
Recording an External Video Signal (HDV/DV In, Analog Line-In) You can record on the tape an external video signal, either from the HDV/DV input (SD or HD standard) or from the analog video input (SD standard). HDV/DV In When recording from an external digital device you can select the time code to be used for the recording made with this camcorder. Select [COPY] to keep the original time code of the video source, or [REGEN.] to use instead this camcorder’s internal time code. 1.
Concerning Copyright Copyright Precaution Certain pre-recorded video tapes, films and other materials, as well as some television programs are copyrighted. Unauthorized recording of these materials may violate copyright protection laws. Copyright Signals During playback: If you try to play back a tape that contains copyright control signals for protection of software, “COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED” appears for a few seconds and the camcorder displays a blank blue screen.
Connecting to a Computer To connect the camcorder to a computer you will need a computer equipped with an IEEE1394 (DV) terminal and video editing software with video capturing capability installed. Use the optional CV-250F (4 pin-6 pin) DV cable or a commercially available 6 pin-6 pin DV cable. For the minimum system requirements for video editing, refer to the instruction manual of the video editing software.
Customization Custom Preset Settings You can select preset level for a number of picture-related parameters (23 parameters when recording movies, 17 when recording still images). A list of the parameters is given in the following table and you can find more detailed descriptions on page 97. After changing individual parameters to your preference, you can save the whole set as a custom preset file.
Enter the custom preset editing screen File name of the currently selected custom preset file Save the custom preset file to the memory card Read a custom preset file from the memory card Overview of the content of the custom preset file Back to the [CUSTOMIZE] submenu Select the custom preset file Change the custom preset settings Rename the custom preset file Back to the options on the left side bar Reset the custom preset to default values Protect the custom preset file Changing Custom Preset Param
Renaming a Custom Preset File Follow steps 1-3 in Changing Custom Preset Parameters ( want to rename. 1. From the bottom bar, select [ 93) to select the custom preset file you RENAME]. The first character of the custom preset file name will start flashing. 2. Turn the SELECT dial to select a number, letter or punctuation mark and press the SET button. • The next character of the custom preset file name will start flashing. • Set the rest of the custom preset file name in the same way. 3.
Activating the Custom Preset Settings 1. Press the CUSTOM PRESET SELECT button. • Repeatedly pressing the button will cycle through the available custom preset files. You can also set a custom key as [CP BKWD KEY] to cycle through the custom preset files in reverse order (from last to first) ( 75). • When you are not using the custom preset settings, set the camcorder to . • and the name of the selected custom preset file will flash on the screen.
Reading a Custom Preset File from a Still Image With the custom function [PHOTO BUTTON] ( 100) you can select to save the custom preset settings currently in use along with a still image recorded in mode (simultaneous recording, 118). This is very useful when you want to load the custom preset file later by selecting the still image captured from a specific scene. 1. Select the still image that contains the custom preset file you want to read. Use the + / – buttons to move between the still images. 2.
[GAM] Gamma Curve The gamma curve changes the overall look of the image. You can select from [NORMAL], [CINE1] or [CINE2]. [NORMAL]: standard gamma setting suitable for video. [CINE1]: appropriate for video telecined from film. [CINE2]: appropriate for transfer to film. Output [NORMAL] [CINE1] [CINE2] Input Representation of the setting [KNE] Knee Point Adjustment Adjust the dynamic range (knee point) in the highlight area of the image to prevent overexposure.
[SHP] Sharpness Adjust the sharpness level in the range -9 to +9. Noise artifacts caused by too-high sharpness settings can be reduced using the coring setting. [HDF] Horizontal Detail Frequency Select the horizontal definition of the image from [HIGH], [MIDDLE] or [LOW]. [DHV] Horizontal/Vertical Detail Balance Adjust the balance between horizontal and vertical definition of the image in the range -9 (only horizontal) to +9 (only vertical). [COR] Coring Adjust the coring level in the range -9 to +9.
[RGN] R Gain Adjust the intensity of red tones in the range -50 to +50. [GGN] G Gain Adjust the intensity of green tones in the range -50 to +50. [BGN] B Gain Adjust the intensity of blue tones in the range -50 to +50. [RGM] R-G Matrix The R-G matrix changes the tint of the picture along the cyan/green and red/magenta gradations without affecting blues. Adjust the level in the range -50 to +50.
Customized Functions You can customize to your personal preferences many aspects of the operation of the camcorder, most of them governing how the camcorder operates in mode. You can adjust up to 3 different custom function files and save them on the camcorder or to a memory card. By just reading the custom function file saved on the memory card with another XL H1S / XL H1A, you will instantly get a camcorder configured to operate in the same familiar manner you prefer.
Resetting a Custom Function File 1. Open the menu, select [CUSTOMIZE] and then select the [CUSTOM FUNCTION] submenu. 2. From the column on the left select the custom function file you want to reset. 3. From the bottom bar select [ RESET]. 4. Select [OK], press the SET button and close the menu. Activating a Custom Function File Even if you define a custom function file, as long as you do not activate it, the camcorder will function according to default settings. 1.
Availability of custom functions in each recording program/playback mode ( Custom Function 00 SHCKLSS WB/GN Video) WHITE BALANCE – (OFF) GAIN – (OFF) 01 ZOOM RING CTRL1 02 ZOOM SPEED 03 FOCUS RING CTRL 04 BUTTONS OPER.1 05 BUTTONS OPER.2 06 RINGS DIRECTION 07 OPER.DIRECTION 08 IRIS LIMIT1 09 PHOTO BUTTON 10 MARKER LEVEL 11 F.AST BW-MOD 1 MAGN.
Availability of custom functions in each recording program/playback mode ( Custom Function 00 SHCKLSS WB/GN 01 ZOOM RING CTRL WHITE BALANCE – (OFF) GAIN – (OFF) 02 ZOOM SPEED 05 BUTTONS OPER.2 06 RINGS DIRECTION 07 OPER.DIRECTION 08 IRIS LIMIT1 09 PHOTO BUTTON 10 MARKER LEVEL 11 F.AST BW-MOD 2 – – (FAST) – 1 MAGN. WB SET REC REVIEW BARS/FADE END SEARCH GAIN SET ZOOM1 FOCUS1 IRIS CURSOR SHUTTER – – – – – – – – – 2 2 2 MARKER ASPECT SAFETY MAGN.
02 [ZOOM SPEED] Zoom Speed Selects the set of 16 constant zoom speeds that will be available when the ZOOM SPEED switch is set to CONSTANT. • When the zoom speed is too fast (less than 2 seconds end-to-end), the camcorder will have more trouble focusing automatically while zooming. Setting Options: [NORMAL], [SLOW], [FAST] 03 [FOCUS RING CTRL] Focus Ring Control Selects the sensitivity of the response when operating the focus ring. Setting Options: [NORMAL], [SLOW], [FAST]. 04 [BUTTONS OPER.
10 [MARKER LEVEL] Markers’ Intensity Level Changes the intensity of the markers displayed on the screen to 40% (gray) or 100% (white). Setting Options: [MARKER] Level/center/grid markers: [100%], [40%] [ASPECT] Aspect ratio guides: [100%], [40%] [SAFETY] Safety zone guides: [100%], [40%] 11 [F.AST BW-MOD] Focus Assist Function B&W Display Mode Changes the display mode to black & white while the focus assist functions are activated. Setting Options: [MAGN.
Customized On-Screen Displays You can customize which icons to display on the screen according to your personal preferences and needs. You can save your personal settings as a custom display file on the camcorder or on the memory card. To activate the on-screen displays at the level that you customized, repeatedly press the EVF DISPLAY button ( 37).
Reading a Custom Display File from the Memory Card 1. Open the menu, select [CUSTOMIZE] and then select [CUSTOM DISPLAY]. 2. From the column on the left select [ READ FROM CARD]. 3. Select [OK], press the SET button and close the menu. When the operation is finished, “TASK COMPLETED” will appear on the screen. Custom display files saved with a Canon XH G1 or XH A1 cannot be used with this camcorder.
12 [TAPE] Tape-Related Icons and Displays Setting Options: [TIME CODE] Time code display: [OFF], [ON] [OPERATION MODE] Icon of the current tape operation: [OFF], [ON] [DV CONTROL] DV control icon: [OFF], [ON] 13 [TAPE REMAINDER] Remaining Time on the Tape You can select to display the tape remainder permanently or only the warning when the tape is about to end.
Location of the Custom Displays / 03 02 09 11 12 19 12 13 20 21 12 14 18 00 01 02 06 04 02 18 07 14 06 08 07 05 14 19 03 19 10 08 02 15 16 19 14 00 17 01 20 21 08 02 06 04 07 19 07 16 05 Customization 06 02 15 109
Playing Back a Tape Playback If the playback picture is distorted, clean the video heads using a Canon DVM-CL video head cleaning cassette or a commercially available digital video head cleaning cassette ( 144). Select a playback standard according to the tape you wish to play back. MENU ( 31) SIGNAL SETUP PLAYBACK STD••••AUTO 1. Set the dial to . 2. Open the menu and select [SIGNAL SETUP]. Select [PLAYBACK STD] and set it to [AUTO], [HDV] or [DV] to match the tape you wish to playback. 3.
(frame advance) Plays back frame-by-frame. Repeatedly press the button on the wireless controller during playback pause. Hold the button pressed down to enter the continuous frame advance playback. (slow forward) Plays back at about 1/3 normal speed. Press the SLOW button on the wireless controller during normal or reverse playback. Press the (play) button to return to normal playback. DV (playback pause) To pause playback, press the during normal playback.
Returning to a Pre-marked Position If you wish to return to a particular scene later, mark the point with the zero set memory, and the tape will stop at that point when you rewind/fast forward the tape. This function is operated with the wireless controller. 1. During playback, press the ZERO SET MEMORY button at the point you wish to return to later. • The tape counter is reset to 0:00:00 and the mark appears. • To cancel, press the ZERO SET MEMORY button again. 2. Stop the playback. 3. Rewind the tape.
Date Search You can locate the change of the date/time zone with the date search function. This function is operated with the wireless controller. 1. Press the SEARCH SELECT button to display the 2. Press the or button to begin searching. icon. • Press more than once to search for further date changes (up to 10 times). • Press the STOP button to stop searching. A recording of longer than a minute per date/time zone is required.
Remote Sensor Mode Two remote sensor modes and an off setting are available to prevent interference from other Canon wireless controllers being used nearby. To change the remote sensor mode of the camcorder Change the custom function [WIRELESS REMOTE] ( 105). To change the remote sensor mode of the wireless controller While holding the REMOTE SET button pressed down, press and hold the ZOOM T button for more than 2 seconds to change the wireless controller to mode 2.
Selecting the Still Image Quality/Size Using a Memory Card Changing the Still Image Quality You can choose from Super fine, Fine and Normal. * * Only when playing back a tape. MENU ( 31) RECORDING SETUP IMG QUALITY•• FINE Open the menu and select [RECORDING SETUP]. Select [IMG QUALITY], select a setting option and close the menu. Changing the Still Image Size Available image sizes will depend on the operating mode and the recording standard settings.
Number of still images that can be recorded on a memory card Image size LW 1920 x 1080 SW 848 x 480 L 1440 x 1080 S 640 x 480 Memory card Image quality File size per image 16 MB 128 MB 512 MB Super Fine 9 90 350 1360 kB Fine 14 135 525 910 kB Normal 28 265 1035 460 kB Super Fine 50 455 1770 280 kB Fine 70 645 2510 190 kB Normal 140 1295 5030 100 kB Super Fine 12 120 470 1020 kB Fine 19 180 700 690 kB Normal 38 350 1370 350 kB Super Fine 65 595 2320
Recording Still Images on a Memory Card You can record still images directly on the memory card. You can also record still images on the memory card simultaneously while recording video on the tape and capture still images while playing back a tape. Using a lens specially designed for HDV recording is required to be able to record still images. As of March 2008, only the following lenses can be used to record still images: HD 6x L, HD 20x L IS II and HD 20x L IS III. PHOTO button 1.
If [CAMERA SETUP] [FOCUS PRI.] is set to [ON]: When you press the PHOTO button fully, before turns green, it may take up to 2 seconds (4 seconds in Night mode) until the focus is adjusted. If the subject is not suitable for autofocus, the camcorder locks the focus. In that case, adjust the focus manually with the focus ring. If [CAMERA SETUP] [FOCUS PRI.] is set to [OFF]: In step 2, turns green and the focus and exposure are locked.
Screen Displays during Still Image Recording Image Quality and Size Indicates the quality and size currently selected for recording still images. Remaining Number of Still Images that can be Recorded on the Memory Card flashing in red: No card in green: 6 or more images in yellow: 1 to 5 images in red: No more images Metering Mode Icon ( 121) Indicates the metering mode currently selected for recording still images.
Drive Mode Drive mode Use Continuous Shooting High-Speed Continuous Captures a quick series of still images while you hold the PHOTO button pressed down. For the number of shots per second, refer to the table below. AEB (Auto Exposure Bracketing) The camcorder records a still image in three different exposures (dark, normal, light in 1/2 EV steps). Single Records a single still image when you press the PHOTO button. Changing the Drive Mode 1.
Metering Mode Metering mode Evaluative Center-weighted average Spot AE Use Appropriate for standard shooting conditions, including backlit scenes. The camcorder divides images into several metering zones. It evaluates the position and brightness of the subject, background, direct light or backlight, and adjusts the exposure of the main subject accordingly. Averages the light metered from the entire screen, giving more weight to the subject in the center. Meters the area within the Spot AE frame. 1.
Using an Optional Flash You can use E-TTL II-compatible Canon Speedlite flashes designed for use with Canon SLR cameras, including the 420EX/430EX/550EX/580EX/580EX II models, to record natural still images under low light conditions. Refer also to the instruction manual of the Speedlite flash. The following procedures are explained using a Canon 580EX II Speedlite Flash.
Playing Back Still Images from a Memory Card 1. Turn the dial to and set the / (card/tape) switch to . 2. Press the + or – button to move between images. Still images not recorded with this camcorder, uploaded from a computer, edited on a computer and still images whose file names have been changed, may not be played back correctly. Observe the following precautions while the card access display appears on the screen or the CARD access indicator is on or flashing.
Image Jump Function You can locate still images without displaying them one by one. The number in the upper right of the screen indicates the number of the current still image out of the total number of still images. Press and hold the + or – button. When you release the button, the still image corresponding to the number that appears on the screen is displayed.
Erasing Still images You can erase still images one at a time or all at once. Be careful when erasing still images. Erased still images cannot be recovered. Erasing a still image that had a custom preset file embedded (recorded with the [PHOTO + CP DATA] setting) will erase the still image and the embedded custom preset file. Protected still images ( 126) cannot be erased. Erasing a Single Still Image 1. Select the still image you wish to erase. 2.
Protecting Still images You can protect important still images from accidental erasure when displaying a single image or the index screen. If a memory card is initialized, all still images, even protected ones, will be erased permanently. Protecting a Single Still Image 1. Select the still image you wish to protect. 2. Press the SET button to open the still image operations menu.
Initializing a Memory Card Initialize new memory cards, or when you get the message “CARD ERROR”. You can also initialize a memory card to erase all data recorded on it. The regular initialization option [INITIALIZE] will clear the file allocation table but will not physically erase the stored data. If you need to completely erase all the data, select instead the complete initialization option [COMPL.INIT.].
Print Order Settings You can select still images for printing and set the number of copies. These print order settings are compatible with the Digital Print Order Format (DPOF) standards and can be used for printing on DPOFcompatible printers. A maximum of 998 still images can be selected. Selecting Still Images for Printing (Print Order) 1. 2. 3. 4. Select the still image you wish to print. Press the SET button to open the still image operations menu. Select [ PRINT ORDER]. Select the number of copies.
Additional Information Menu Options and Default Settings In the following tables, default settings are shown in boldface and the availability of menu settings in different operating modes is indicated with the following icons: : CAMERA MENU ( dial set to one of the recording modes, : VCR/PLAY MENU ( dial set to : CARD CAMERA MENU ( : CARD PLAY MENU ( , / / switch is set to switch set to dial set to one of the recording modes, dial set to , / ) ) switch set to / switch set to ) ) SIGNA
CAMERA SETUP Menu item (Submenu item and) Setting options AGC LIMIT OFF(18dB), 15dB, 12dB, 9dB, 6dB, 3dB – – 66 SKIN DETAIL EFFECT LEVEL OFF, LOW MIDDLE , , HIGH – – 72 HUE 0 (-6 to 6) CHROMA 0 (-6 to 6) AREA 0 (-6 to 6) Y LEVEL 0 (-6 to 6) EFFECT LEVEL OFF, LOW MIDDLE , , HIGH – – 73 HUE 0 (-6 to 6) CHROMA 0 (-6 to 6) AREA 0 (-6 to 6) Y LEVEL 0 (-6 to 6) CORRECT OFF, A – – 70 A AREA SEL., B AREA SEL.
[DV REC MODE]: When recording in standard definition (SD mode) only, you can choose between SP (standard play) and LP (long play). LP extends the tape usage by 1.5 times. Depending on the tape and its usage condition, picture and sound recorded in LP mode may be distorted. We recommend using SP mode for important recordings. If you record in both SP and LP modes on the same tape, the playback picture may become distorted, and the time code may not be written correctly.
DISPLAY SETUP/ Menu item (Submenu item and) Setting options EVF SETUP EVF BW MODE ON, OFF BRIGHTNESS 0 (-23 to 22) CONTRAST 0 (-23 to 22) COLOR 0 (-3 to 3) SHARPNESS 2 (1 to 4) PEAKING1 GAIN: 8 (OFF to 15) PEAKING SETUP 22 – – 44 FREQUENCY: 2 (1 to 4) PEAKING2 GAIN: 15 (OFF to 15) FREQUENCY: 1 (1 to 4) LANGUAGE DEUTSCH, ENGLISH, ESPAÑOL, FRANÇAIS, ITALIANO, POLSKI, , , MARKERS OFF, LEVEL MARK., CENT.MARK., GRID MARKER – – – ASPECT GUIDE OFF, 4:3, 13:9, 14:9, 1.66:1, 1.
SYSTEM SETUP/ (cont.) Menu item (Submenu item and) Setting options CUSTOM KEY2 TIME CODE, INDEX WRITE, ZEBRA, VCR STOP, TV SCREEN, TC HOLD, AUDIO LEVEL, EVF BW MODE, MAGN.B.LOCK, SHTR B.LOCK, AE D.LOCK, E.LCK B.LCK, CP BKWD KEY, FB, FLIP EVF, SDI OUTPUT1, FOCUS LIMIT, (NONE) – TIME CODE, TV SCREEN, DATA CODE, AUDIO LEVEL, TC HOLD, EVF BW MODE, SDI OUTPUT1, (NONE) – ZEBRA, TV SCREEN, EVF BW MODE, MAGN.B.LOCK, SHTR B.LOCK, AE D.LOCK, E.LCK B.
Custom Preset Submenu (CUSTOMIZE CUSTOM PRESET) Submenu item Action (Parameter and) Setting Options EDIT SELECT CP 1 PRESET_A, 2 PRESET_B, 3 PRESET_C, 4 PRESET_D, 5 PRESET_E, 6 PRESET_F, 7 VIDEO.C, 8 CINE.V, 9 CINE.F TUNE [GAM] GAMMA* NORMAL, CINE1, CINE2 [KNE] KNEE AUTO, LOW, MIDDLE, HIGH [BLK] BLACK STRETCH, MIDDLE, PRESS [PED] MASTER PED.
Custom Function Submenu (CUSTOMIZE CUSTOM FUNCTION) Submenu item Action (Custom Function and) Setting Options C.Fn1, C.Fn2, C.Fn3 APPLY THIS SET DISABLED, ACTIVE TUNE 00 SHCKLSS WB/GN 00 (00 to 03) 01 ZOOM RING CTRL 00 NORMAL, 01 SLOW, 02 FAST 02 ZOOM SPEED 00 NORMAL, 01 SLOW, 02 FAST 03 FOCUS RING CTRL 00 NORMAL, 01 SLOW, 02 FAST 04 BUTTONS OPER.1 00 (00 to 03) 05 BUTTONS OPER.2 00 (00 to 15) 06 RINGS DIRECTION 00 (00 to 07) 07 OPER.
Custom Displays Menu item Action (Custom Display and) Setting Options CUSTOM DISPLAY TUNE 00 REC PROGRAMS 00 OFF, 01 ON 01 CAMERA DATA1 03 (00 to 03) 02 CAMERA DATA2 07 (00 to 07) 03 ZOOM 00 OFF, 01 ON(NORMAL), 02 ON(ALWAYS) 04 FOCUS 00 OFF, 01 ON(NORMAL), 02 ON(ALWAYS) 05 ND 00 OFF, 01 ON 06 IMAGE EFFECTS 07 (00 to 07) 07 F.ASSIST FUNC.
Settings Memorized and Retained The following lists show the settings that are memorized and retained under different circumstances like turning off the camcorder, setting it to standby or changing operating modes. If the built-in lithium button battery discharges completely, all settings will be erased.
Screen Displays Screen Displays during Recording You can find additional explanations on pages 36 and 119. Most of the on-screen displays and icons can be customized using the custom displays ( 106).
Screen Displays during Playback Side panel Time code Video signal standard Time code setting Video output signal from the HD/SD SDI Terminal Tape has reached the end Remaining battery charge Time code synchronization setting Manual audio adjustment Audio level indicator 139 Additional Information Audio monitor ( 86) Audio output ( 86) Custom function ( 100) Custom keys ( 75) Data code ( 113) Date search ( 113)/ Index search ( 112)/ End search ( 39) Recording standard ( 38) Frame rate ( 48) Tape oper
List of Messages (in alphabetical order) Message CARD ERROR Explanation A memory card error occurred. The camcorder cannot record or play back the image. The error may be temporary. If the message disappears after 4 seconds and flashes in red, turn the camcorder off, remove the card and reinsert the card. If changes to green, you can continue recording/playback. – CARD FULL No remaining capacity on the memory card. Replace with another card or erase images.
Maintenance/Others Camcorder Handling Precautions Do not carry the camcorder by the viewfinder, the microphone or its cable. Do not leave the camcorder in places subject to high temperatures, such as a sun-heated car, and high humidity. Do not use the camcorder in places subject to strong electromagnetic fields such as near TV sets, plasma TVs, radio transmitters or portable communication devices. Do not point the lens or viewfinder at strong light sources.
1. Open the protecting cover (e.g. using a flathead screwdriver). 2. Clean the glass with a cotton swab. 3. Reattach the protecting cover. Be careful not to scratch the glass when cleaning it. Battery Pack Handling Precautions DANGER! Treat the battery pack with care. • Keep it away from fire (or it might explode). • Do not expose the battery pack to temperature higher than 60 ºC. Do not leave it near a heater or inside a car in hot weather. • Do not try to disassemble or modify it.
Cassette Handling Precautions Rewind tapes after use. If the tape is lose or damaged, it may cause picture and sound distortion. Return cassettes to their case and store them upright. Rewind tapes from time to time if they are stored for a long time. Do not leave the cassette in the camcorder after use. Do not use spliced tapes or nonstandard cassettes as they may damage the camcorder. Do not use tapes that have been jammed as video heads may become dirty.
Built-in Rechargeable Lithium Battery The camcorder has a built-in rechargeable lithium battery to keep the date/time and other settings. The built-in lithium battery is recharged while you use the camcorder; however, it will become totally discharged if you do not use the camcorder for about 3 months. To recharge the built-in lithium battery: Connect the compact power adapter to the camcorder and leave it connected for 24 hours with the camcorder off.
Resuming use: It takes about 1 hour until the water droplets evaporate. After the condensation warning stops flashing, wait for 1 more hour before resuming use. Using the Camcorder Abroad Power Sources You can use the compact power adapter to operate the camcorder and to charge battery packs in any country with power supply between 100 and 240 V AC, 50/60 Hz. Consult a Canon Service Center for information on plug adapters for overseas use.
Troubleshooting If you have a problem with your camcorder, refer to this checklist. Consult your dealer or a Canon Service Center if the problem persists. Power Source Problem Cause Solution Camcorder will not turn on. Battery pack is not correctly attached. Attach the battery pack correctly. 15 The camcorder switches off by itself. Power save function has been activated. Turn on the camcorder. 35 The screen switches on and off. Battery pack is exhausted. Replace or charge the battery pack.
Recording Problem Cause Solution A vertical light bar appears on the screen. Bright light in a dark scene may cause a vertical light bar (smear) to appear. This is not a malfunction. Record in Av mode with an aperture value in the range F5.6–F8.0. 64 Viewfinder picture is blurred. Viewfinder is not adjusted. Adjust the viewfinder with the dioptric adjustment lever. 21 Audio is not recorded.
System Diagram (Availability differs from area to area) ZR-1000 Zoom Remote Controller FU-2000 Color Viewfinder Unit ZR-2000 Zoom Remote Controller FU-1000 Monochrome CRT Viewfinder Unit 3 Speedlite Flash 420EX, 430EX, 550EX, 580EX, 580EX II SS-1100 Shoulder Strap SBR-1000 Shooting Brace Extender XL 1.6x 1 Memory Card (SD/SDHC/MMC) WL-D5000 Wireless Controller 16x IS II Zoom Lens XL 5.5-88 mm RC-72 Ratio Converter MiniDV Video Cassette 5 16x Manual Zoom Lens XL 5.4-86.
1 2 3 4 5 Can be attached to the HD 20x L IS III, HD 20x L IS II, HD 6x L, 20x L IS, 16x IS II and 16x manual zoom lenses (only for recording in SD mode). EF-S lenses cannot be used. When you use the FU-1000 Monochrome CRT Viewfinder with this camcorder you can use the compact power adapter or the optional CB-920 Car Battery Adapter as the power source.
Optional Accessories Use of genuine Canon accessories is recommended. This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack).
EF Adapter XL This allows you to attach Canon EF lenses to the camcorder. The difference in size between the camcorder’s 1/3-inch CCD’s and 35 mm film means that the effective focal length of still camera lenses is multiplied by 8.8x (4:3)/7.2x (16:9). • Consult your local service outlet to make sure there are no compatibility problems with your chosen lens. FU-1000 Monochrome CRT Viewfinder Unit Professional quality B&W viewfinder with a 1.5-inch CRT.
FU-2000 Color Viewfinder Unit When the FU-2000 is connected to the color viewfinder socket of the camcorder, it is possible to review the on screen picture without having to be next to the camcorder. Also, by connecting the FU-2000 to the optional ZR-2000 Remote Zoom Controller you can have complete control of the main operations of the camcorder while reviewing the on-screen picture without touching the camcorder. This mark identifies genuine Canon video accessories.
Specifications XL H1S / XL H1A System Video Recording System Audio Recording System Television System Tape Format Tape Speed Maximum Recording Time (60 min.
Terminals HD/SD SDI Terminal BNC jack, output only, 0.8 Vp-p/75 ohms, unbalanced SDI 576/50i: ITU-R BT.656, SMPTE 272M, SMPTE RP 188 (LTC) HD SDI: SMPTE 292M, SMPTE 299M, SMPTE RP 188 (LTC) Special 6-pin connector (IEEE1394 compliant) input/output 1080i (D3)/576i (D1) compatible 4-pin mini-DIN jack 1 Vp-p/75 ohms (Y signal), 0.
CA-920 Compact Power Adapter Power supply Rated output Operating temperature Dimensions Weight 100 – 240 V AC, 50/60 Hz Adapter: 7.2 V DC, 2.0 A, 35 VA (100 V AC) - 47 VA (240 V AC) Charger: 8.4 V DC, 1.5 A, 29 VA (100 V AC) - 40 VA (240 V AC) 0 – 40 °C 75 x 99 x 51 mm 215 g excluding the power cable BP-950G Battery Pack Battery type Rated voltage Operating temperature Battery capacity Dimensions Weight Rechargeable lithium ion battery 7.4 V DC 0 – 40 °C 5,200 mAh 38.2 x 40.3 x 70.
Index A Abroad, using the camcorder . . . . . . . . . . . . . . . . . . . . . . . 145 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 150 AE shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 AEB - Auto exposure bracketing . . . . . . . . . . . . . . . . . . . . 120 Analog line-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Analog/digital (A/D) converter . . . . . . . . . . . . . .
Power save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Print order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Programmed AE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Protecting still images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35, 137 Still image quality . . . . . . . . . . . . . . .
Canon Europa N.V. Bovenkerkerweg 59-61, 1185 XB Amstelveen, The Netherlands Canon UK Ltd. CCI Service Centre, Unit 130 Centennial Park, Borehamwood, Hertfordshire, WD6 3SE, England Telephone 0870-241-2161 Canon Australia Pty. Ltd. Info-Line: 131383 www.canon.com.au Canon New Zealand Ltd. Customer Care: (09) 489 0470 www.canon.co.nz Canon Singapore Pte.
