Installation & Assembly

ManualsBrandsCanopia by Palram ManualsAwningsFeria 24 ft. W x 10 ft. D Plastic Standard Patio Awning

Steps:

Step 2: To assemble the rear prole please refer to the patio cover assembly manual at the stage of

"holes marking" as:

Feria Tuscany Olympia Sierra Joya Carnival

3x3 - Step 7 3x3 - Step 7 3x3 - Step 5

All sizes

Step 5

All sizes

Step 6

3x3 - Step 6

3x4.25 - Step 6 3x4.25 - Step 9 3x4.25 - Step 7 3x4.25 - Step 5

3x5.46 - Step 9 3x5.46 - Step 9 3x5.46 - Step 7

4x4.25 - Step 12

- - -

For xation to the wall, return to step 2.

Step 3: connect part 8303 (drawings a,b) and than return to the patio cover assembly manual as follow:

Feria Tuscany Olympia Sierra Joya Carnival

3x3 - Step 8

3x3 -

Step

3x3 - Step 6 2.3x2.3 - Step 7 3x3 - Step 7 3x3 - Step 10

3x4.25 - Step 13

3x4.25 -

Step

13 3x4.25 -

Step

3x3 - Step 6

3x4.25 - Step 10

3x4.25 - Step 9

3x5.46 -Step 13

3x5.46 -

Step

13 3x5.46 -

Step

3x4.25

Step

3x5.46 - Step 10

4x4.25 -Step 16

3x5.46 - Step

After completion, perform drawing c at this step.

Step 4: In all relevant patio cover sizes, you may choose either of these 2 assembly options:

Option 1 (Steps 4+5+6+9+10+11+12) - assembling all posts supplied.

Option 2 (Steps 4+7+8+9+10+11+12) - Whenever you are using this EZ Link Kit you may give up using

one leg.

Step 6 (Option 1) : make sure the distance between the post and the connection point does not exceed

60 cm / 23.6 inch. The Maximum distance between the posts may not exceed 120 cm / 47.2 inch.

Step 10: before performing this stage, return to the patio cover assembly manual at the stage of

"assembling the roof system" as follow:

Feria Tuscany Olympia Sierra Joya Carnival

3x3 - Step 15

3x3 -

Step

3x3 -Step 11

2.3x2.3 -

Step

3x3 - Step 13 3x3 - Step 18

3x4.25 - Step 22

3x4.25 -

Step

20 3x4.25 -

Step

3x3 - Step 11 3x4.25 - Step 17 3x4.25 - Step 16

3x5.46 - Step 21

3x5.46 - 20

Step

3x5.46 -

Step

3x4.25

Step

15 3x5.46 -

Step

4x4.25 - Step 26

3x5.46 - Step

Step 12: Tightening the bolts is done from the inner part. Spread silicone follow the connection (a,b).

Pay attention: while installing the kit, alignment with original patio cover is important.

Tighten all screws when completing assembly.

When encountering the information icon, please refer to the relevant

assembly step for additional comments and assistance.

This icon indicates that the installer should be inside the product.

Please read these instructions carefully before you start to

assemble this product.

Please carry out the steps in the order set out in these instructions.

Keep these instructions in a safe place for future reference.

Safety

• Some parts may have sharp edges. Please be careful when handling components.

• Always wear gloves, eye protection, and long sleeves when assembling or performing

any maintenance on your product.

• To prevent injuries, do not allow children to play under the product during assembly.

Before Assembly

• This product is suitable for Palram’s Patio Covers range

• It is highly recommended to be assisted by a second person in some steps.

• Sort the parts and check according to the contents parts list.

• Prior to the installation, some parts of the Patio cover need to be

dismanteld, it is recommend to keep them in a safe place for future use.

• Periodically check the kit’s components to assure that it remains stable.

• Note: Use only the parts registered in the content list, which are compatible

with your Patio Cover›s gutter (7999 & 8119), some parts may be surplus.

During Assembly

In case that you already own Palram Patio cover it is necessary to

dismantle parts as described in Step 1 in the kit assembly manual.

74803_20.09_V4.1 _MV-5