sauder.com Your center of attention. Media Stand Model 424274 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. Prefer the phone? Call 1-800-445-1527. Share your journey! PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-18 Français pg 19-21 Español pg 22-24 Lot #: 528952 Date Purchased: __________________ 05/01/19 Be sure to give us a ring before making any returns.
Table of Contents Part Identification Hardware Identification Assembly Steps Assembly Tools Required 3 No. 2 Phillips Screwdriver Tip Shown Actual Size 4 5-18 Hammer Français 19-21 Español 22-24 Safety 25-26 Warranty Not actual size Skip the power trip. This time. 27 ! WARNING Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or death.
Now you know our ABCs. Part Identification å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Hardware Identification å Screws are shown actual size. You may receive extra hardware with your unit. 1 HIDDEN CAM - 17 2 3 6 DOOR BRACKET - 4 7 PIN WITH SLEEVE - 8 11 APPLIQUE CARD - 3 12 BUMPER CARD - 1 CAM SCREW - 17 WOOD DOWEL - 12 8 METAL PIN - 4 4 BRACKET - 4 5 RETAINING BAR - 4 PULL - 2 10 NAIL - 30 9 13 WARNING LABEL - 1 5 lbs.
Look for this icon. It means a video assembly tip is available at www.sauder.com/services/tips Step 1 å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor. å Push seventeen HIDDEN CAMS (1) into the ENDS (A and B), UPRIGHTS (C and D), BOTTOM (F), and VALANCE (G). Arrow Arrow (17 used) 1 1 G F A C D B Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. 424274 www.sauder.
Step 2 å Turn seventeen CAM SCREWS (2) into the exact holes shown in the ENDS (A and B) and TOP (E). Remember: Righty tighty. Lefty loosey. A 2 B E Page 6 www.sauder.
Step 3 å å Insert one WOOD DOWEL (3) into the LEFT END (B). å NOTE: Be sure the WOOD DOWEL in the LEFT END inserts into the VALANCE (G). å å Insert one WOOD DOWEL (3) into the LEFT END (B). å NOTE: Be sure the WOOD DOWEL in the LEFT END inserts into the BOTTOM (F). 1 Fasten the VALANCE (G) to the LEFT END (B). Tighten one HIDDEN CAM. 2 Fasten the BOTTOM (F) to the LEFT END (B). Tighten two HIDDEN CAMS.
Step 4 å å Insert two WOOD DOWELS (3) into the RIGHT END (A). å NOTE: Be sure the WOOD DOWELS in the RIGHT END insert into the BOTTOM and VALANCE. å å Insert two WOOD DOWELS (3) into the BOTTOM (F). å NOTE: Be sure the WOOD DOWELS in the BOTTOM insert into the UPRIGHTS. Fasten the RIGHT END (A) to the BOTTOM (F) and VALANCE (G). Tighten two HIDDEN CAMS. Fasten the UPRIGHTS (C and D) to the BOTTOM (F). Use four BLACK 2” FLAT HEAD SCREWS (15).
Step 5 å å Insert six WOOD DOWELS (3) into the TOP (E). å NOTE: Be sure the WOOD DOWELS in the TOP insert into the ENDS, UPRIGHTS, and VALANCE. Fasten the TOP (E) to the ENDS (A and B), UPRIGHTS (C and D), and VALANCE (G). Tighten eleven HIDDEN CAMS. 3 B E D G C Edge with more CAM SCREWS 424274 A www.sauder.
Step 6 å å Unfold the BACK (H) and lay it over your unit. å å Fasten the BACK (H) to your unit using the NAILS (10). å NOTE: Perforations have been provided for access through the BACK. Caution Make equal margins along all four edges of the BACK (H). Push on opposite corners of your unit if needed to make it “square”. Do not stand the unit upright without the BACK fastened. The unit may collapse. NOTE: Tap NAILS into the holes that line up over the UPRIGHTS (C and D).
Step 7 å Fasten the SHORT BRACE (P) to the LONG BRACES (O). Tighten four BLACK 1/2” HEX HEAD SCREWS (21) using the L-WRENCH (14). å Fasten the FOOT (Q) to the SHORT BRACE (P). Tighten two BLACK 1/2” HEX HEAD SCREWS (21) using the L-WRENCH (14). å Fasten the LEGS (N) to the LONG BRACES (O). Tighten four BLACK 1/2” HEX HEAD SCREWS (21) using the L-WRENCH (14). Side Step: Make nachos. (Optional, but recommended.) These holes must be facing up.
Step 8 å å Carefully turn your unit onto its top. å Fasten the LEGS (N) to the BOTTOM (F). Use four BLACK 1-9/16” WAFER HEAD SCREWS (16). å Fasten the LONG BRACES (O) to the BOTTOM (F). Use eight BLACK 1-1/4” WAFER HEAD SCREWS (17). NOTE: Start each SCREW a few turns before completely tightening any of them. 16 BLACK 1-9/16" WAFER HEAD SCREW (4 used in this step) 17 BLACK 1-1/4" WAFER HEAD SCREW (8 used in this step) N O F O 16 Page 12 N www.sauder.
Step 9 å å Carefully stand your unit upright. å NOTE: Position the BRACKETS exactly as shown. Fasten four BRACKETS (4) to the VALANCE (G). Use four BLACK 1/2” FLAT HEAD SCREWS (20). G 4 20 BLACK 1/2" FLAT HEAD SCREW (4 used in this step) 424274 www.sauder.
Step 10 å Fasten the TUBE (R) to the BRACKETS (4). Use four BLACK 3/8” MACHINE SCREWS (22). å NOTE: Start each SCREW a few turns before completely tightening any of them. å Insert four METAL PINS (8) into the hole locations of your choice in the center surfaces of the UPRIGHTS (C and D). Set the grooves in the LARGE SHELF (J) onto the PINS. å Insert eight PINS WITH SLEEVES (7) into the hole locations of your choice in the ENDS (A and B) and UPRIGHTS (C and D). Set the SMALL SHELVES (K) onto the PINS.
Step 11 å Fasten the RETAINING BARS (5) to the DOORS (L and M) exactly as shown. Use eight BLACK 1/2” PAN HEAD SCREWS (19). å Fasten the PULLS (9) to the DOORS (L and M) exactly as shown. Use four BLACK 1/2” FLAT HEAD SCREWS (20). 20 BLACK 1/2" FLAT HEAD SCREW (4 used in this step) Su rfa ce wi th m or e ho le s 9 20 M wi th Su rfa ce 9 m or e ho le s BLACK 1/2" FLAT HEAD SCREW L 5 19 BLACK 1/2" PAN HEAD SCREW (8 used in this step) 424274 www.sauder.
Step 12 å Place the RETAINING BARS on the DOORS (L and M) into the groove in the BOTTOM (F). å å Place the DOOR BRACKETS (6) onto the TUBE (R). Almost time to celebrate! With a nap. Fasten the DOOR BRACKETS (6) to the DOORS (L and M). Use eight BLACK 9/16” LARGE HEAD SCREWS (18). L R F M 6 18 BLACK 9/16" LARGE HEAD SCREW (8 used in this step) Page 16 www.sauder.
Step 13 å Apply the WARNING LABEL (13) to the TOP (E). You should be able to read the label when the TV is removed from the unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram. å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it. 5 lbs. 70 22,68 kg 31,75 31,75 22,68 kg 2 2 ,6 8 13 5 kg 2 2 ,6 8 31,7 5 kg 5 31,7 70 lbs. E 424274 www.sauder.
Step 14 å å IMPORTANT: The BUMPERS are used to reduce the risk of fingers being pinched when sliding the DOOR. å å å Peel APPLIQUES from the APPLIQUE CARDS (11) and stick them onto each visible HIDDEN CAM. Peel the BUMPERS from the BUMPER CARD (12) and stick the BUMPERS on the PULLS and on the upper and lower corners of the inner sides of the DOORS (L and M). NOTE: Please read the back pages of the instruction booklet for important safety information. This completes assembly. Clean with a damp cloth.
Modèle 424274 Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
AVERTISSEMENT ÉTAPE 4 L'utilisation d'un téléviseur trop lourd ou trop gros est dangereuse. Un téléviseur trop lourd créera un risque de basculement pouvant provoquer de graves blessures ou la mort. Un téléviseur trop gros pour l'espace disponible risque d'être accidentellement poussé ou de tomber du mobilier ou d'être sujet à basculer. • Vérifier la taille et le poids du téléviseur.
ÉTAPE 8 ÉTAPE 12 Avec précaution, retourner l'élément sur son dessus. Placer les LANGUETTES DE RETENUE sur les PORTES (L et M) dans la rainure du DESSOUS (F). REMARQUE : Il est préférable de donner quelques tours de tournevis à chaque VIS avant de les serrer toutes à bloc. Fixer les PIEDS (N) au DESSOUS (F). Utiliser quatre VIS TÊTE MINCE 40 mm NOIRES (16). Fixer les ENTRETOISES LONGUES (O) au DESSOUS (F). Utiliser huit VIS TÊTE MINCE 32 mm NOIRES (17).
Modelo 424274 Use estas instrucciones de ensamblaje en español junto con las figuras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las figuras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identification” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
ADVERTENCIA PASO 4 El uso de un televisor demasiado pesado o grande es peligroso. Un televisor demasiado pesado generará riesgo de caída, lo cual podría causar lesiones graves o muerte. Un televisor demasiado grande para el espacio disponible puede ser empujado o golpeado por accidente, causando que éste se salga del mueble o se caiga. Inserte dos PASADORES DE MADERA (3) dentro del EXTREMO DERECHO (A). • Verifique el tamaño y peso del televisor.
PASO 8 PASO 12 Cuidadosamente voltee la unidad para que repose sobre el panel superior. Coloque las BARRAS DE RETENCIÓN de las PUERTAS (L y M) en la ranura del FONDO (F). NOTA: Comience a atornillar cada TORNILLO unas vueltas antes de apretar cualquier tornillo firmemente. Coloque los SOPORTES DE PUERTAS (6) sobre el TUBO (R). Fije las PATAS (N) al FONDO (F). Utilice cuatro TORNILLOS NEGROS DE CABEZA DE DISCO de 40 mm (16). Fije las RIOSTRAS LARGAS (O) al FONDO (F).
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following safety information. Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result may tip over onto the child.
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Lea cuidadosamente la siguiente información de seguridad. Pueden suceder lesiones graves o la muerte cuando los niños se suben en los muebles de equipo de audio y/o video. Un control remoto o juguetes colocados en el mueble pueden alentar a un niño a subirse en el mueble y como resultado puede derribarse sobre el niño.
5-YEAR LIMITED WARRANTY 1. Sauder Woodworking Co. (Sauder®) provides limited warranty coverage to the original purchaser of this product for a period of five years from the date of purchase against defects in materials or workmanship of Sauder furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 2.
Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the purchase and assembly process was a positive experience and you feel good about the furniture you just built. If you need assistance or want to learn more, please contact our award-winning, Ohio-based customer service team at 1-800-445-1527 or Sauder.com. Set a world record for speed? Feeling good about yourself? Nice. Get social with it on any of these quality share sites.
