Instruction manual

ManualsBrandsCaple ManualsHousehold AppliancesCE1500

Set the clock

TO SET THE CLOCK FOR THE FIRST TIME

1. You must switch off the radio before you set the clock.

2. Press and hold the “TIME SET” button until the display

begins to blink then release the button.

3. Press the Hour and Minute button to adjust the hour and

minute respectively. The PM indicator will light when the

hour is set in the PM.

4. Press the “TIME SET” button once to confirm the time

set.

Note: in future you can also adjust the time by pressing and

holding the ‘TIME SET’ Button for 2 seconds in clock mode

(radio off). The hour and minute digits will start to flash.

Then you can follow the step 3 to step 4 to adjust the time.

Use the alarm

TO SET THE ALARM

You can set two alarms (ALARM 1 & 2) with the following

steps:

1. Turn the unit to Clock mode (radio off).

2. Press and hold the Alarm 1 Button for 2 seconds. The

hour and minute digits will start to flash.

3. Press the Hour Button to adjust the hour.

4. Press the Minute Button to adjust the minute.

5. Press the Alarm 1 Button for confirmation.

6. Press the Alarm 1 Button for selection of how you want to

be awakened.

• A LED lights up at Clock symbol means a buzzer

sounds when the alarm time is reached.

• A LED lights up at Music Note symbol means

the radio will be switched on at the last set station

when the alarm time is reached.

7. You can turn off the alarm by pressing the Alarm 1 Button

repeatedly until no LED lights up at the symbols.

Note: you can set the ALARM 2 by repeating the above

steps with the Alarm 2, Hour and Minute Button.

TO REVIEW THE ALARM

1. After the alarm has been set, you can review the alarm

time by pressing and holding the Alarm 1 or Alarm 2 button

for 2 seconds. The alarm time will be blinking on the display.

2. After 5 seconds, it will go back to normal time display.

TO STOP THE ALARM AND RESET THE ALARM READY

FOR THE NEXT DAY

1. Press the ALARM OFF button to stop the alarm.

2. The alarm will be automatically reset and gets ready for

the next day.

SNOOZE FUNCTION

1. Press the SNOOZE button when alarm rings. The alarm

will be silenced for 9 minutes and then sound again.

2. SNOOZE button can be pressed 6 times. Then the alarm

will stop automatically and gets ready for the next day.

DIMMER FUNCTION

Press the DIMMER button to adjust the brightness of LED

display.

Use the radio

TO TUNE THE RADIO TO DESIRED STATION MANUALLY

1. Press the ON/OFF button to turn on the radio.

2. Press the AM/FM button to select desired band.

3. Press and hold the Tune + or Tune – button for 2

seconds, the unit will scan upward or downward until a

station with strong signal is found and stops at this station.

4. You can adjust the frequency manually by pressing the

Tune + or Tune – button.

5. Press the Volume + or Volume - button to adjust the

volume to the desired level.

6. Press the ON/OFF button to turn off the radio.

PRESET RADIO STATION

1. Press the ON/OFF button to turn on the radio.

2. Press AM/FM button once to change from AM to FM

radio and vice versa.

3. Press and hold the Tune + or Tune – button for 2

seconds to search for a desired radio station.

4. Press and hold the PRE/M+ button for approximate 2

seconds, then the preset station number “P01” will be

displayed and flashes.

5. Press the PRE/M+ button to save it.

6. Press the PRE/M+ button to skip the preset station

number to “P02”.

7. Repeat step 2 to step 5 to save other stations. You

can save up to 10 AM and FM radio stations in the

memory.

TO LISTEN TO A PRESET RADIO STATION

1. Press the ON/OFF button to turn on the radio.

2. Press PRE/M+ button to skip to the radio station you

stored last time.

3. You can adjust the frequency manually by pressing

the Tune + or Tune – button.

Use the sleep timer

IMPORTANT: Due to the continued functioning of

revisions and improvements in the design of our products,

specifications are subject to change without notice.

SPECIFICATION

Power Supply

(AC Power Adaptor)

Input: AC 120V, 60Hz

Output: DC 6V, 200mA

Frequency Range

Of Radio

AM 530 - 1710 kHz

FM 87.5 - 108 MHz

Dimensions 7.0” x 4.6” x 3.3”

(179mm x 116mm x 84mm)

Weight 0.48 lb. (0.22 kg)

Back-up Battery 3V (2 pcs AAA Size LR03 or R03

battery, not included)

Power Consumption 3W (max.)

What’s in the box

Connect the power

CE1500 AM/FM PLL Alarm Clock Radio

Instruction Manual

Warranty Card

ADT Digital LLC

Plug the small end of the supplied power adaptor into the

DC IN jack at the back of the unit. Plug the adaptor body

into the standard AC wall socket (AC 120V 60Hz).

2. Remove the battery door and insert 2 pieces of AAA 1.5V

battery (not included) into the battery compartment (be sure

to observe the polarity) and then replace the battery door.

AC Power Adatpor

Use the aux in

1. Plug one end of a standard 3.5mm stereo audio cable

into the earphone jack on your portable device and the

other end into the unit’s AUX IN jack.

2. Turn on the unit and play your portable device.

3. Turn off your portable device and unplug from the unit

after using.

Distributed by ADT Digital, LLC.

1900 Glades Road, Boca Raton, FL 33431

Printed in China

CE1500_QSG_EN_V1.0

Visit our website at

www.ADT-DIGITAL.com

CE1500

Instruction Manual

Connect the power

Set the clock

Use the alarm

Use the radio

Use the sleep timer

Please read this instruction manual before

operating your unit.

1. Wake to Radio Indicator (Alarm 1)

2. Wake to Buzzer Indicator (Alarm 1)

3. PM Indicator

4. Snooze / Dimmer Button

5. AM/FM/AUX Button

6. Tune- / Hour Button

7. Tune+ / Minute Button

8. Radio Station / Memory / Time Set Button

9. Sleep Button

10. Volume- / Alarm1 Set Button

11. Volume+ / Alarm2 Set Button

12. Radio On-Off / Alarm Off Button

13. Antenna

14. LED Dispaly

15. Wake to Buzzer Indicator (Alarm 2)

16. Wake to Radio Indicator (Alarm 2)

17. Sleep Timer On Indicator

AM/FM PLL ALARM CLOCK RADIO

Use the aux in

TO SET SLEEP TIMER

1. You must switch off the radio before you set the sleep

timer.

2. Press the SLEEP button once to activate the sleep

timer to 90 minutes with “90” in the LED display and

the radio is turned on.

3. Press the SLEEP button repeatedly to adjust the

sleep timer to 80, 70, 60, 50, 40, 30, 20, 10 minutes

and then OFF. “OFF” means to cancel the sleep timer

and turn the radio off.

4. When the sleep timer is counting down, press the

SLEEP button to display the remaining time.

5. If you want to change the sleep timer, press the

SLEEP button repeatedly to the new sleep time.

TO CANCEL SLEEP TIMER

1. When the sleep timer is counting down, press the

SLEEP button repeatedly until “OFF” is displayed.

2. Alternatively, press the ON/OFF button once to turn

off the radio.

Battery compartment

(at the bottom of the unit)

DC IN jack

AUX IN jack

AUX IN

DC 6V

5 6 7 8 9 10 11 13

Summary of content (2 pages)

PAGE 1
AM/FM PLL ALARM CLOCK RADIO Visit our website at www.ADT-DIGITAL.com CE1500 What’s in the box CE1500 AM/FM PLL Alarm Clock Radio AC Power Adatpor ADT Digital LLC Instruction Manual 1 2 3 4 5 6 1 Connect the power Warranty Card Note: you can set the ALARM 2 by repeating the above steps with the Alarm 2, Hour and Minute Button. Connect the power Instruction Manual 1. Plug the small end of the supplied power adaptor into the DC IN jack at the back of the unit.
PAGE 2
WARNING: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN C A U T I O N : TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. This symbol is intended to alert you to the presence of uninsulated dangerous voltage within the product’s enclosure that might be of sufficient magnitude to constitute a risk of electric shock.