Instruction manual for deluxe electronic dishwasher Model code: Di617 Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.
Dear Customer, Please carefully read this manual before using the dishwasher, it will help you to use and maintain the dishwasher properly. Keep it to refer to it at a later date. Pass it on to any subsequent owner of the appliance. This manual contains sections on safety Instructions, Operating Instructions, Installation Instructions and Troubleshooting Tips, etc. Control Panel...................................................3 Dishwasher Features............................ ......... ...
WARNING! When using your dishwasher, follow the precautions listed below: This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of anelectric shock by providing a path of least resistance of electric current. This appliance is equipped with a cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.
Dispose of the dishwasher packaging material correctly. All packaging materials can be recycled. Plastic parts are marked with the standard international abbreviations: PE for polyethylene, e.g. sheet wrapping material PS for polystyrene, e.g. padding material POM PP ABS polyoxymethylene, e.g. plastic clips polypropylene, e.g. Salt filler Acrylonitrile Butadiene Styrene, e.g. Control Panel .
To get the best performance from your dishwasher, read all operating instructions before using it for the first time. OFF ON Di617 1 2 3 2 ON/OFF Button: To turn on/off the power supply. 2 Power on light: To come on when Power ON/OFF button is pressed down. 3 Half washing button:To select half washing. (Optional half washing means that the lower spray arm does not run, so you should load the upper basket only). 4 Delayed Start Button: Press this button to set the delayed hours for washing.
Before using your dishwasher for the first time: A. Set the water softener B. Pour 1/2 litre of water inside the salt container and then fill with dishwas her salt C. Fill the rinse aid dispenser D. Fill in detergent The water softener must be set manually, using the water hardness dial. The water softener is designed to remove minerals and salts from the water, which would have a detrimental or adverse effect on the operation of the appliance.
Always use the salt intended for use with dishwasher. The salt container is located beneath the lower basket and should be filled as explained in the foll owing: Attention! Only use salt specif ically de signed for the use in dishwashers! Every othe r type of salt not specifically designed for the use in a dishwasher, espe cially t able sa lt, will damage the water softe ner.
When to Refill the Rinse Aid Dispenser If there is no rinse-aid warning light in the control panel, you can judge the amount of rinse-aid by the color of the optical level indicator "C" located next to the cap. When the rinse-aid container is full, the whole indicator will be dark .As the rinse-aid diminishes, the size of the dark dot decreases. You should never let the rinse aid get below 1 / 4 full.
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the dishwasher. Most of the commercial quality detergents are suitable for this purpose.
Fill in detergent Fill the detergent dispenser with detergent. The marki ng indicates the dosing levels , as illustrated on the right: A The place of main wash cycle detergent placed , “MIN”means approximately 20g of detergent. B The place of pre-wash cycle detergent placed , approximately 5g of detergent Please observe the manufacturers dosing and storage recommendations as stated on the detergent packaging. Close the lid and press until it locks in place.
How To Use The 3IN1 Program Your dishwasher has a 3in1 program which needs no salt and rinse aid but a 3In1 tablet. This dishwasher comes with a 3in1 tablet container as an accessory. Only the 3in1 program can be used with 3in1 tablets. If you use 3in1 tablets in other programs, The appliance will not achieve a good performance. 1. The figure below shows how to hang the 3in1 tablet container on the upper basket. 2.
For best performance of the dishwasher, follow these loading guidelines. Features and appearance of baskets and cutlery baskets may vary from your model. Attention before or after Loading the Dishwasher Baskets Scrape off any large amounts of leftover food. Soften remnants of burnt food in pans. It is not necessary to rinse the dishes under running water. Place objects in the dishwasher in following way: 1.Items such as cups, glasses, pots/pans, etc. are faced downwards. 2.
Loading the Lower Basket We recommend that you place large items which are most difficult to clean in to the low er basket: pots, pans, lids, serving dishes and bowls, as shown in the figure to the right. It is preferable to place serving dishes and lids on the side of the racks in order to avoi d blocking the rotation of the top spray arm. Pots, serving bowls, etc. must always be placed top down. Deep pots should be slanted to allow w ater to flow out.
Cutlery Basket Cutlery should be placed in the cutlery basket with the handles at the bottom. If the rack has side baskets, the spoons should be loaded separately into the appropriate slots, especially long utensils should be placed in the horizontal position at the front of the upper basket as shown in the picture.
Di shes and items of cutlery must not lie inside one another, or cover each othe r To avoid damage to glasses, they must not touch Load large items which are most difficult to clean into the lower rack T he upper rack is designed to hold more delicate and lighter dishware such as glasses, coffee and tea cups Attention! Long bladed knives stored in an upri ght position are a potential hazard! Long and/or sharp items of cutl ery such as carving knives must be positioned horizontally in the upper basket.
For normally soiled loads, such as pots , plates,glasses and lightly soiled pans. standard daily cycle. Pre-wash pre-wash wash45 rinse68℃ drying Strong For the heaviest soiled loads, such as pots,pans,casserole dishes and dishes that have been sitting with dried food on them for a while. Normal 3in1 160 1.15 17.2 Pre-wash Pre -wash( 5 0℃) Wash (60 ℃) Rinse (70 ℃) Drying 5/25 g. 160 1.4 17 For normally soiled loads, such as pots , plates,glasses and lightly soiled pans. standard daily cycle.
Turning on the Appliance Starting a wash cycle... 1 Draw out the lower and upper basket, load the dishes and push them back. It is commended that loading the lower basket first, than the upper one (see the section entitled “Loading the Dishwasher”). 2 Pour in the detergent (see the section entitled “Sal t, Detergent and Rinse Aid”). 3 Insert the plug into the socket. The power supply is 220-240 VAC 50 HZ, the specification of the socket i s 10 A 250 VAC.
Switch Off the Dishwasher In the digital display appears 0 (remaining programme time),only in this case the programme has ended. 1.Switch off the dishwasher by pressing the ON/OFF button. 2.Turn off the water tap! Open the door carefully. Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes before removing from the appliance. Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes.
Filter assembly For best performance and results, the filter assembly must be cleaned. The filter efficiently removes food particles from the wash water, allowing it to be recycled during the cycle. For best performance and results, the filter must be cleaned regularly. For this reason, it is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular fi lter and cup under running water.
To clean the edge around the door, you should use only a soft warm, damp cloth. To avoid penetration of water into the door lock and electrical components, do not use a spray cleaner of any kind. Never use a spray cleaner to clean the door panel as it may damage the door lock and electrical components. Abrasive agents or some paper towels should not be used because of the risk of scratching or leaving spots on the stainless steel surface.
【Figure1】 Cabinet dimensions Less than 5mm between the top of dishwasher and cabinet and the outer door aligned to cabinet. 90 ° 90 ° 820mm 600mm Electrical, drain and water supply line entrances 80 100 Space between cabinet bottom and floor 600 mm 【Figure2】 Dishwasher Minimum space when the door is opened Cabinet Door of dishwasher Minimum space of 50mm ● 1 Aesthetic panel's dimensions and installation The aesthetic wooden panel could be processed according to the Figure 3.
2 Install the hook on the aesthetic wooden panel and put the hook into the slot of the outer door dishwasher(see figure 4a). After positioning of the panel , fix the panel onto the outer door by screws and bolts(See figure 4b) . Hop hook 【Figure4a】 Installation of aesthetic panel St4 countersunk head screw Lower hook 【Figure4b】 4X18 screw Cover Installation of aesthetic wooden panel Spacer for furniture door 1. Take away the cover 2. Pin up the screw 3.
● Tension adjustment of the door spring The door springs are set at the factory to the proper tension for the outer door. If aesthetic wooden panel are installed, you will have to adjust the door spring tension. Rotate the adjusting screw to drive the adjustor to strain or relax the steel cable(see figure 5). Adjust the door spring tension until the door remains balance in the fully-opened position.
● Dishwasher installation steps 1 Install the furniture door to the outer door of the dishwasher using the brackets provided. Refer to the template for positioning of the brackets. 2 Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to tighten the left and right door springs. Failure to do this could cause damage to your dishwasher (Illustration 2) . 3 Connect the inlet hose to the cold water supply . 4 Connect the drain hose. Refer to diagram .
Dishwasher must be level for proper dish rack operation and wash performance. 1 Place level on door and rack track inside the tub as shown to check that the dishwasher is level. 2 level the dishwasher by adjusting the four leveling legs individually. 3 When level the dishwasher, pl ea s e pay attention not to let the dishwasher tip over. 【Figure 8】 Illustration of feet adjustment Check Level Front to Back NOTE: The maximum adjustment height of the feet is 60 mm.
The appliance must be connected to the water mains using new hose-sets. The old hose-sets should not be reused. Water pressure must be between 0,04 MPa and 1 MPa. If the pressure is below the minimum consult our Service Department for advice. 1 Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher. 2 Tighter the screws of the safety supply hose to the faucet with thread 3/4inch. 3 Turn water fully on before starting the dishwasher.
Technical problems General problems Fuse blown, or the circuit breaker acted Replace fuse or reset circuit breaker. Remove any other appliances sharing the same circuit with the dishwasher Power supply is not turned on Make sure the dishwasher is turned on and the door is closed securely. Make sure the power cord is properly plugged into the wall socket. Error code:E1; Water pressure is low Check that the water supply is connected properly and the water is turned on.
Unsatis -factory washing result Unsatis -factory drying result The dishes were not loaded correctly. See notes in " Loading the Dishwasher Baskets ". The programme was not powerful enough. Select a more intensive programme. See" Wash Cycle Table ". Not enough detergent was dispensed. Use more detergent, or change your detergent. Items are blocking the path of spray arms. Rearrange the items so that the spray can rotate freely.
595 820 Height : Width : Depth : Voltage connected Load : Water pressure: Hot water connection : Power supply: Capacity: 820mm(adjustable+60mm) 595mm 560mm see rating label 0.04-1.