Instruction manual for built-under larder fridge Model code:RBR5 Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.
Contents Cautions---------------------------------------------------------------------------------------1~2 Diagram----------------------------------------------------------------------------------------3 Preparation------------------------------------------------------------------------------------4~5 Operation--------------------------------------------------------------------------------------6 Instruction-------------------------------------------------------------------------------------7~10 Defrosting
1. Compression-type appliances which use flammable refrigerants shall be marked with the symbol "Caution:risk of fire" Caution：risk of fire The height of the triangle in the symbol “Caution: risk of fire” shall be at least 15 mm. 2. – WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction. – WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
Cautions Disposal of the old appliance Before disposing an old appliance, please make sure it’s inoperative and safe. Unplug the appliance and remove or destroy all of the springs, latches, or bolt-locks in order to avoid the risk of child entrapment. It must be noted that the refrigeration system contains insulating gases and refrigerants, which require specialized waste disposal. The valuable materials contained in a refrigerator can be recycled.
2
Refrigerator Diagram 1.Freezing compartment 2.Temperature Controller 3.Shelves 4. Egg tray 5. Bottle racks This diagram may vary slightly with the layout of the refrigerator you have just purchased due to technical improvements.
Preparation Unpacking Remove all packing materials. Check attachments and materials Checking should be conducted with reference to the Packing List. Contact the local distributor if discrepancies are found. Ensure proper location of the refrigerator. Clean the refrigerator before use. (See the following section “Cleaning”) Idle time After the refrigerator has been sited and cleaned, let it stand for more than 12 hours before connecting the power source.
Preparation Installation（Figure 2） 1.Check that the kitchen unit door is in the correct operating position. 2.Run the mains cable through the unit such that it can be connected to the power supply after installing the appliance. Remove the cover (6) only if space is restricted. 3.Place the refrigerator into the kitchen unit. Fix the mountings (1) with screws (2) onto the upper frame when two third of the refrigerator has been pushed in.
Caution: Some time will be required for the refrigerator to reach the set level when temperature adjustments are made. The length of this period is determined by difference in the existing and set temperatures, the ambient temperature, the frequency with which the door is opened and closed and the amount of food in storage. Caution: If ambient temperature is below 16℃, please turn on the “Low-temp Controller”.
Instructions Cold storage is for short-term food Storage or for daily consumption. Although the temperature in most parts of the cold storage compartment can be regulated between 0 and 10 degrees Centigrade, extended periods of food storage is not recommended. Cold storage should only be used for short-term storage. Cold storage compartment 1. Eggs and butter 2. Beverages and bottled food 3. Food to be frozen 4.
Shelf cleaning Lamp & Replacement: Lamp: 240V, 10W Lamp holder: E14 (lamps exceeding 15W must not be used) * For replacement, unplug to disconnect the power * Remove the lamp by turning anti-clockwise 8
9
Making ice cubes 10
operating 11
Prolonged power failure 12
work Dry food 13
Installation guide for built-under refrigeration Please carefully read this guide before installing the appliance.
6 1 2 7 3 8 4 9 5 1
10 550 Min 595 825-900 600 497 540 178 480 25 11 1200 596 596 5 2
15 = 15 5 = 13 12 3 9mm 2 14 3
15 16 4
17 18 5
EN DOOR REVERSAL 1. Unplug the appliance before reversing the door opening direction. 2. Remove food from the appliance. 3. Remove caps on the front of the refrigerator body (Fig. 1, Fig 2). 4. Remove the two screws, which attach the upper hinge to the appliance door (Fig. 3). Take special care and hold the appliance door vertically. 5. Holding the door, swing the upper door hinge away from the door using the other hand (Fig. 4).
