The IMPRESSA J5 Manual The ‘IMPRESSA Manual’ has been awarded the seal of approval by the independent German Technical Inspection Agency, TÜV SÜD, due to its easy-to-understand style, its thoroughness and coverage of safety aspects.
Table of contents Your IMPRESSA J5 IMPORTANT SAFEGUARDS 4 8 Control elements and accessories Proper use 10 For your safety ............................................................................................................................................ 10 The IMPRESSA J5 Manual 13 Symbol description ....................................................................................................................................
Table of contents 5 Permanent settings in programming mode 36 Buttons........................................................................................................................................................ 36 Energy Save Mode .....................................................................................................................................37 Time................................................................................................................................
Important Safeguards IMPORTANT SAFEGUARDS These safeguards apply for machines with UL safety test (see rating plate and chapter 10, ‘Technical data and guide values’). Follow the basic safety precautions When using electrical appliances, basic safety precautions should always be followed, to reduce the risk of fire, electric shock, and/or injury to persons, including the following: Read all instructions. Do not touch hot surfaces. Use handles or knobs.
Important Safeguards Special cord set instructions a. A short power supply cord is provided to reduce the risk resulting from becoming entangled in or tripping over a long cord. Your IMPRESSA has a 3-pin grounded plug. b. Longer extension cords are available and may be used if care is exercised in their use. c. If an extension cord is used, 1. the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance, and 2.
Important Safeguards p p NEVER DO (or you will void your warranty protection): p p p p 6 Keep your hands and the cord away from hot parts of the appliance during operation. Never clean with scouring powders or hard implements. Never fill instant coffee, chocolate mix etc. into the grinder or ground coffee funnel (grunder by-pass). It will damage the functioning of the brewing chamber Never fill sugar coated coffee beans into the bean hopper. In case of doubt, call your dealer.
Important Safeguards 7
Control elements and accessories Control elements and accessories 8 9 1 2 10 11 3 12 4 13 14 15 5 16 6 17 7 Figure: IMPRESSA J5 Piano White 1 Bean container with aroma preservation cover 2 Plain text display 3 Water tank 4 Height/width-adjustable coffee spout 5 Coffee grounds container 6 Drip tray 7 Cup platform 8 8 Filler funnel for pre-ground coffee 9 Fineness of grind switch 10 Storage compartment with measuring spoon and hot water nozzle 11 Power switch and power cable (side) 12 Connector
Control elements and accessories 1 2 3 4 5 6 7 8 9 Surface of the machine 1 2 3 G ö h On/Off button Rotary Switch Maintenance button Display 4 5 6 7 8 9 a s q k d f 1 Espresso button 2 Espressi button Hot water button Steam button 1 Coffee button 2 Coffees button 9
The IMPRESSA J5 Manual The IMPRESSA J5 Manual You are holding the manual for your IMPRESSA J5 in your hand. It will help you to familiarize yourself with your IMPRESSA safely and quickly and teach you the full range of facilities it offers. Chapter 2, ‘Preparing and using your IMPRESSA for the first time’, explains step-by-step how to set up and prepare the IMPRESSA.
Important information Proper use The machine has been designed and built for domestic use. It should only be used to prepare coffee and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use. Before using the machine always carefully read and comply with all these instructions. Keep this manual close to the IMPRESSA and, if appropriate, pass it on to the next user.
Important information There is a risk of scalds or burns on the spouts or in the nozzle: Place the machine out of the reach of children. Do not touch any hot parts. Use the handles provided. Be careful to ensure that the appropriate nozzle is installed and clean. The nozzle or parts of the nozzle might come off if the parts are not assembled correctly or a blockage occurs. p p p A defective machine is not safe and could cause injury or fire.
Important information Risk to children and persons with limited capabilities in operating machines: The machine is not designed to be operated by children and persons with limited capabilities. The machine may only be used by persons who are able to operate the machine safely. p p Safe handling of the CLARIS filter cartridges: Filter cartridges should be kept out of the reach of children. Store them dry in the sealed package. Protect them from heat and direct sunlight.
The IMPRESSA J5 Manual Symbol description Warnings CAUTION CAUTION Always take note of any information marked with the CAUTION or WARNING symbol. The signal word WARNING points out potential risk of serious injury, and the signal word CAUTION potential risk of slight injury. The CAUTION symbol is used to draw attention to circumstances which could cause the machine to become damaged. Symbols used o Information and tips to make things easier for you as you use your IMPRESSA.
1 IMPRESSA J5 – Perfect Enjoyment, Perfected Aesthetics 1 IMPRESSA J5 – Perfect Enjoyment, Perfect Aesthetics Coffee that fulfils your wildest dreams JURA develops superior fully automatic coffee/Espresso machines which get the best taste and aroma out of every coffee blend and roast. It delivers this through a unique, intelligent pre-brew system combined with loving attention to detail and years of experience.
1 IMPRESSA J5 – Perfect Enjoyment, Perfect Aesthetics JURA on the Internet p Height and width-adjustable coffee spout Another JURA innovation is the height and width-adjustable coffee spout. It allows precise adaptation to different cup heights and diameters. This prevents coffee splashing and guarantees a fantastic crema of ideal consistency.
2 Preparing and using your IMPRESSA for the first time 2 Preparing and using your IMPRESSA for the first time This chapter provides you with the information you need to use your IMPRESSA without any problems. You will prepare your IMPRESSA step-by-step for your first coffee experience using it. Keep the packaging for your IMPRESSA. It is used to protect the machine during transportation.
2 Preparing and using your IMPRESSA for the first time l Remove any dirt or foreign objects inside the bean container. l New machines contain an information sheet in the bean container. Remove this information sheet. l Fill the bean container with coffee beans, then close the aroma preservation cover and the bean container cover. First-time use WARNING If the machine is operated with a defective power cable, there is a danger of electric shock. l Never use a machine which has a defective power cable.
2 Preparing and using your IMPRESSA for the first time l Place a receptacle under the coffee spout. h l Press the maintenance button. The machine will rinse itself, stopping automatically. READY appears on the display. Your IMPRESSA is ready to use. o After the first time that a coffee speciality has been prepared, it may happen that FILL BEANS appears on the display if the grinder has not yet been completely filled with coffee beans. In that case, prepare a different coffee speciality.
2 Preparing and using your IMPRESSA for the first time l Lift the cartridge holder and insert the filter cartridge into the water tank, applying light pressure. l Close the cartridge holder. It will click into place audibly. l Fill the water tank with cold, fresh mains water and reinsert. l Place a receptacle (at least 500 ml) under the Professional h Cappuccino Frother. l Turn the selection lever of the nozzle to the steam position k . l Press the maintenance button. FILTER RINSING.
2 Preparing and using your IMPRESSA for the first time l You will then be able to read the degree of water hardness from the discolouration of the Aquadur® test strip and the description on the packaging. You can now adjust the water hardness. Example: To change the water hardness from 16°dH to 25°dH, proceed as follows: Precondition: READY appears on the display. M l Keep the Rotary Switch pressed until, RINSE appears on the display. Ä l Turn the Rotary Switch until HARDNESS - is displayed.
2 Preparing and using your IMPRESSA for the first time p Select a coarse setting for a darker roast. u If the consistence of grind is too coarse, the coffee flows too quickly from the coffee spout. Example: To change the fineness of grind during coffee preparation, proceed as follows: l Open the cover of the storage compartment. l Place a cup under the coffee spout. d l Press the 1 Coffee button. The grinder starts and 1 COFFEE appears on the display. After this, the coffee strength is briefly displayed.
2 Preparing and using your IMPRESSA for the first time Switching off (standby) When you switch off your IMPRESSA, the system is automatically rinsed. l Place a receptacle under the coffee spout. g l Press the On/Off button. The system will be rinsed. RINSING appears on the display. The operation stops automatically. The IMPRESSA is switched off (in standby mode), and the On/Off symbol is illuminated.
3 Familiarising yourself with the control options 3 Familiarising yourself with the control options With the IMPRESSA, you can prepare an excellent coffee speciality at the touch of a button. You also have the option of adjusting the coffee strength and temperature, as well as the amount of water to your personal taste. This chapter will allow you to become familiar with all control options with the aid of examples.
3 Familiarising yourself with the control options a l Press the 1 Espresso button. 1 ESPRESSO appears on the display. After this, the coffee strength is briefly displayed. The pre-set amount of water flows into the cup and the process stops automatically. READY appears on the display. One-off settings before and while your drink is being prepared You can change both the coffee strength before and the amount of water while your drink is being prepared. These settings are not saved.
3 Familiarising yourself with the control options Ä l Turn the Rotary Switch until 110 ML is displayed. The set amount of water flows into the cup. The preparation stops automatically. READY appears on the display. Permanent settings according to cup size It is easy to make permanent settings for the amount of water for all coffee specialities, the hot water and steam according to cup size. As in the following example, adjust the amount of water once.
3 Familiarising yourself with the control options You can make the following settings with the Rotary Switch: Programme item Subitem Explanation RINSE RINSE FILTER CLEAN DE-SCALE l Select the desired maintenance programme. BUTTONS SELECT BUTTON l Select your settings for the coffee specialities, FILTER -/√ YES √ NO - If you don’t take any action, the programming mode is exited after approx. 5 seconds. steam and hot water.
3 Familiarising yourself with the control options Example: To change the temperature of 1 Espresso from NORMAL to HIGH proceed as follows: Precondition: READY appears on the display. M l Keep the Rotary Switch pressed until RINSE appears. Ä L Turn the Rotary Switch until BUTTONS appears. M l Press the Rotary Switch to enter the programme item. SELECT BUTTON o In the next step, select the coffee speciality button for which you would like to make settings. No coffee speciality will be prepared hereby.
3 Familiarising yourself with the control options M l Press the Rotary Switch to enter the programme item. BUTTONS M l Press the Rotary Switch. Total number of the prepared coffee specialities appears on the display. o By pressing the individual buttons, the respective number of coffee specialities, steam and hot water is displayed. Open the filler funnel for pre-ground coffee in order to display this number. M l Press the Rotary Switch. BUTTONS Ä L Turn the Rotary Switch until EXIT appears.
3 Familiarising yourself with the control options o The filled out fields show the care status. Once all fields are filled out, your IMPRESSA will request the respective maintenance programme. M l Press the Rotary Switch to exit this query. CLEAN Ä L Turn the Rotary Switch until EXIT appears. M l Press the Rotary Switch to exit this programme item. INFO Ä L Turn the Rotary Switch until EXIT appears. M l Press the Rotary Switch to exit the programming mode.
4 Preparation at the touch of a button 4 Preparation at the touch of a button In this chapter, you will find out how to prepare coffee specialities, milk and hot water without making further settings. Chapter 3, ‘Familiarising yourself with the control options’, will teach you how to adjust the settings to your personal preferences. Alternatively, you can use Chapter 5, ‘Permanent settings in programming mode’. o You can stop the machine at any time while a coffee speciality is being prepared.
4 Preparation at the touch of a button To prepare two cups of coffee, place two cups under the coffee spout and press the 2 Coffees button f. Cappuccino A classic Italian recipe. The Cappuccino is made up of one-third each of Espresso, hot milk and milk foam. The finishing touch is a sprinkling of cocoa powder. Precondition: The Professional Cappuccino Frother is mounted. l Take the milk pipe out of the Welcome Pack. l Take the protective cap off the Professional Cappuccino Frother.
4 Preparation at the touch of a button l Move the cup under the coffee spout. a l Press the 1 Espresso button. 1 ESPRESSO appears on the display. After this, the strength is briefly displayed. The pre-set amount of water flows into the cup. Drink preparation stops automatically. READY appears on the display. To ensure that the Professional Cappuccino Frother works perfectly, you should rinse and clean it regularly.
4 Preparation at the touch of a button l Open the cover for pre-ground coffee. FILL PRE-GROUND l Place one level measuring spoon of pre-ground coffee in the filler funnel. l Close the cover for pre-ground coffee again. SELECT BUTTON d l Press the 1 Coffee button. 1COFFEE appears on the display. After this, PRE-GROUND is briefly displayed. The pre-set amount of water flows into the cup and the process stops automatically. READY appears on the display.
4 Preparation at the touch of a button To ensure that the Professional Cappuccino Frother works perfectly, you should rinse and clean it regularly. The description for this can be found in Chapter 6, ‘Maintenance – Professional Cappuccino Frother’. Hot water CAUTION To obtain a perfect water flow, attach the exchangeable hot water nozzle. You can find the nozzle under the cover of the storage compartment. There is a danger of scalding from hot water splashes. l Avoid direct contact with the skin.
5 Permanent settings in programming mode 5 Permanent settings in programming mode Buttons In the following you will find out how to make permanent settings. Buttons Temp.
5 Permanent settings in programming mode A L Press the 1 Espresso button. WATER Ä L Turn the Rotary Switch until TEMP. appears. M l Press the Rotary Switch to enter the programme item. NORMAL Ä L Turn the Rotary Switch until HIGH appears. M l Press the Rotary Switch to confirm the setting. OK appears briefly on the display. TEMP. L Turn the Rotary Switch until EXIT appears. Ä M l Press the Rotary Switch to exit the programme item. BUTTONS Ä L Turn the Rotary Switch until EXIT appears.
5 Permanent settings in programming mode M l Press the Rotary Switch to enter the programme item. SAVE - Ä L Turn the Rotary Switch until SAVE √ appears. M l Press the Rotary Switch to confirm this selection. OK appears briefly on the display. ENERGY √ L Turn the Rotary Switch until EXIT appears. Ä M l Press the Rotary Switch to exit the programming mode. READY Time If the machine is disconnected from the mains, the time has to be reset. Precondition: READY appears on the display.
5 Permanent settings in programming mode M l Press the Rotary Switch to enter the programme item. --:-- appears on the display. Ä M Ä M L Turn the Rotary Switch to set the hour. l Press the Rotary Switch to confirm the hour setting. L Turn the Rotary Switch to set the minutes. l Press the Rotary Switch to confirm the minute setting. OK appears briefly on the display. UNIT ON L Turn the Rotary Switch until EXIT appears. Ä M l Press the Rotary Switch to exit the programming mode.
5 Permanent settings in programming mode Units amount of water/ time format The unit for the amount of water is set in the factory. You can set the unit for the amount of water to ML or OZ. The time format is set in the factory. You can set the formats 24 HRS or AM/PM. Example: To change the unit for the amount of water from ML to OZ, proceed as follows. Precondition: READY appears on the display. M l Keep the Rotary Switch pressed until RINSE appears. Ä L Turn the Rotary Switch until DISPLAY appears.
5 Permanent settings in programming mode M l Press the Rotary Switch to enter the programme item. ENGLISH Ä L Turn the Rotary Switch until FRANCAIS appears. M l Press the Rotary Switch to confirm the setting. OK appears briefly on the display. LANGUE L Turn the Rotary Switch until EXIT appears. Ä M l Press the Rotary Switch to exit the programming mode. PRET appears on the display.
6 Maintenance 6 Maintenance Your IMPRESSA has the following integrated maintenance programmes: Rinse machine Changing the filter Clean machine Descale machine p p p p o Clean or descale the machine or change the filter whenever the appropriate indicator is lit up. Maintenance tips To ensure that you get many years’ reliable service out of your IMPRESSA and to guarantee the optimum coffee quality, the machine requires daily maintenance.
6 Maintenance Precondition: READY appears on the display. l Place a receptacle under the coffee spout. M l Keep the Rotary Switch pressed until RINSE appears. M l Press the Rotary Switch to enter the programme item. RINSE M l Press the Rotary Switch to initiate the rinse operation. RINSING, rinsing stops automatically and your IMPRESSA is now ready for use. Changing the filter o After 50 litres of water have flowed through, the filter will cease to work.
6 Maintenance l Turn the selection lever of the nozzle to the steam position k . h l Press the maintenance button. FILTER RINSING - Water will flow out at the nozzle. o You can interrupt the filter rinsing at any time. To do this, press any button. o The water may be slightly discoloured. This is not harmful to health, nor does it affect the taste. Filter rinsing stops automatically after approx. 500 ml. HEATING appears on the display, and then READY appears.
6 Maintenance o The cleaning programme only lasts about 15 minutes. o Do not interrupt the cleaning programme. The quality of cleaning will be impaired if you do so. o JURA cleaning tablets are available from your stockist. @ You can also try out the ‘Clean machine’ operation online. Visit the Knowledge Builder at www.jura.com. Cleaning following a prompt Precondition: CLEAN / READY appears on the display, and the maintenance button h lights up. h l Press the maintenance button.
6 Maintenance M l Press the Rotary Switch to enter the programme item. RINSE Ä l Turn the Rotary Switch until CLEAN appears. M l Press the Rotary Switch. EMPTY TRAY l Continue with the second prompt to take action (indicated by l), as is described under ‘Cleaning following a prompt’. Descale machine CAUTION The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it. The degree of calcification depends on the degree of hardness of your water.
6 Maintenance Descaling following a prompt Precondition: DE-SCALE / READY appears on the display, and the maintenance button h lights up. h l Press the maintenance button. EMPTY TRAY l Empty the drip tray and coffee grounds container and put them back into the machine. AGENT IN TANK l Remove the water tank and empty it. l Completely dissolve the contents of one blister (3 JURA des- h caling tablets) in a container that holds 500 ml of water. This may take several minutes.
6 Maintenance l Replace the nozzle. The descaling operation is now complete. The IMPRESSA heats up and is ready for use again. o If the descaling operation stops unexpectedly, rinse the water tank thoroughly. Manual descaling You can initiate the operation ‘Descaling the machine’ manually. Precondition: READY appears on the display and the filter is not activated. M l Keep the Rotary Switch pressed until RINSE appears. M l Press the Rotary Switch to enter the programme item.
6 Maintenance l Turn the selection lever to the milk k or milk foam position. l Press the steam button. HEATING READY k l Press the steam button again. STEAM - The nozzle and pipe are rinsed. l Press any button as soon as clean water flows into the cup. Clean Professional Cappuccino Frother CAUTION To ensure that the Professional Cappuccino Frother works perfectly, you should clean it daily when you have been preparing milk.
6 Maintenance STEAM – The nozzle and pipe are cleaned. l Press any button as soon as the receptacle with the Auto- k ä Disassemble Professional Cappuccino Frother Cleaning the bean container Cappuccino Cleaner is empty. l Rinse the receptacle thoroughly, fill it with 250 ml of fresh water and immerse the milk pipe in it. l Press the steam button. l Turn the Rotary Switch until 60 SEC appears on the display. STEAM - The nozzle and pipe are rinsed with fresh water.
6 Maintenance l Loosen the screw in the beam container and lift up the finger protection. l Remove the remaining beans with a vacuum cleaner. l Clean the bean container with a soft, dry cloth. l Put the finger protection down again and screw it back tightly in place. l Fill the bean container with coffee beans, then close the aroma preservation cover and the bean container cover. The cleaning of the bean container is now complete.
7 Display messages 7 Display messages Message Cause/Result Action EMPTY TRAY The drip tray is full.You cannot prepare any coffee or hot water or milk products. l Empty the drip tray. FILL WATER TANK Water tank is empty. You cannot prepare any coffee specialities or hot water or milk products. l Fill the water tank (See The coffee grounds container is full. You cannot prepare any coffee specialities, but you can prepare hot water or milk.
7 Display messages Message Cause/Result Action CLOSE COVER The cover for pre-ground coffee is open. l Close the cover for pre-ground coffee. NOT ENOUGH PRE-GROUND l The next time you prepare There is too little pre-ground coffee, fill in more pre-ground coffee in the filler funnel. The IMPRESSA stops the operation. coffee (see Chapter 4, ‘Preparation at the touch of a button – Pre-ground coffee’). TOO HOT System is too hot to begin a maintenance programme.
8 Troubleshooting 8 Troubleshooting Problem Cause/Result Action Grinder is making a very loud noise. There are foreign objects in the grinder. l Contact Customer Support in your coun- The frother does not produce enough milk foam. The Professional Cappuccino Frother is dirty. l Clean the Professional Cappuccino Coffee only comes out in drips when it’s being prepared. Coffee or pre-ground coffee has been ground too finely and is blocking the sieve.
8 Troubleshooting Problem Cause/Result Action ERROR 2 is displayed. If the device was exposed to the cold for a long period of time, it is disabled from heating up due to safety reasons. l Warm up the device at room Other ERROR messages are displayed. – temperature. l Turn your IMPRESSA off at the power switch. Contact Customer Support in your country (see ‘JURA contact details / Legal information’).
9 Transport and environmentally neutral disposal 9 Transport and environmentally neutral disposal Transport / Empty system Keep the packaging for your IMPRESSA. It is used to protect the machine during transportation. In order to protect the IMPRESSA from frost during transportation, the system must be emptied. Precondition: The IMPRESSA must be switched off (standby). l Remove the water tank. l Place a receptacle under the nozzle. h l Press the maintenance button until EMPTYING is displayed.
10 Technical data 10 Technical data Voltage 230 V AC, 50 Hz 120 V AC, 60 Hz 220 – 240 V AC, 50 Hz 220 V AC, 50 Hz Safety test Power consumtion in standby mode 2.8 Wh Power 1450 W Power consumption 12 Wh SAVE Power consumption 7 Wh SAVE √ Pump pressure Static max. 15 bar Holding capacity of water tank 2.1 l Holding capacity of bean container 250 g Holding capacity of coffee grounds container Approx. 16 servings Cable length Approx. 1.1 m Weight 10.75 kg Dimensions (W x H x D) 28.
Index Index A Activating Filter 18 Addresses 60 Adjusting Amount of water 35 Coffee strength 35 Energy-saving mode 36 Grinder 20 Strength 35 Temperature 35 Water hardness 19 Aroma preservation cover 7 D Descale Machine 45 Water tank 50 Display Plain text 7 Drip tray 7 E Energy Save Mode Adjusting 36 Espresso 30 F Filling Bean container 16 Water tank 16 Filter Activating 18 Change 42 Inserting 18 First-time use 17 B Bean container 7 Cleaning 49 Filling 16 Button Maintenance 8 On/off 8 C Cappuccino 31 C
Index M R Machine Clean 43 Descaling 45 Rinse 41 Set up 16 Switching off 21 Switching on 21 Maintenance 41 Milk Milk pipe 7 Warm 33 Rinse Machine 41 Professional Cappuccino Frother 47 Rotary Switch 8, 14 S Safety 9 Settings Amount of steam 35 Permanent settings in grogramming mode 35 Setting the time 37 Specialities 30 Spout 15 Standby 21 Storage compartment 7 Switch-on time Setting 37 Switching off machine 21 Switching on machine 21 N Nozzle Hot water nozzle 34 Number Buttons, prepared 28 Maintenance
Art. 66362/J5/en/200908 JURA contact details / Legal information JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Phone: +41 62 38 98 233 @ Contact information is available on the company website at www.jura.com. Directives The machine complies with the following EU directives: 2006/95/EC – Low Voltage Directive 2004/108/EC – Electromagnetic Compatibility p p Technical changes We reserve the right to make technical changes.