Installatie & gebruikershandleiding Installation & user guide Most of our car radios are after-market systems and specifically composed for a particular car make and model.
Contents Introduction ............................................................................................................................................ 4 Glossary ................................................................................................................................................... 5 General tips when installing a car stereo ................................................................................................
Note for car play function: ................................................................................................................ 15 Note for Android auto function: ....................................................................................................... 15 Other things that need attention: ..................................................................................................... 15 (1). CarPlay wired connection method .....................................................
Introduction This guide explains how to set up and install the product so that you can enjoy the product to the fullest. In the unlikely event that you do not find a solution, we advise you to contact us by email via info@carmultimedia.nl. We recommend that the installation be carried out by a specialist. Check out our website www.carmultimedia.nl for more information about connecting / installing by our specialists.
Glossary Iso adapter plug: The plug you click between the car plug and the radio Ready-made system: A system that is specifically made for a certain car brand/type. These systems are supplied without a framework. Key wires: These wires are specifically needed to connect to a steering wheel adapter lead (this is the case with universal systems with a pass front). Our multimedia is supplied if your car supports it with a can bus.
360o view camera: these are cameras, one front, one rear, one left, one right and have 360o display. If your car has the 360o view camera from the factory, then the advice is to have a multimedia with WDR support. Factory reset You can go to the factory settings of the device via settings – system or car settings.
White connector on the plug that you can put in the back of the Radio can plug with the can bus wires. If possible, connect it to the car stereo. 2. Connect the radio antenna to the antenna of your car. It may be that you have an AM / FM connection in your car (double plug) there is only one to be connected. The blue cable can be connected to the P.ANT blue connector. (Antenna amplifier) 3. Place the GPS antenna in the highest possible position under the dashboard or on the dashboard.
1. Step 2 Connect the antenna adapter plug between the original antenna connector and the radio. If there is still a blue wire attached to the antenna overflow, it can be linked with AMP CON or ANT (often also a blue wire). This ensures that the antenna amplifier is powered / activated. 1. Step 3 Place the Wi-Fi antenna if your model is over a separate Antenna has as shown here. You can place the antenna in a place as high as possible under the dashboard.
The yellow wire must be provided with a constant power supply. This wire ensures that the radio remembers its memory. Not every car has a switched power supply in the plug block. Connect/connect switched power supply A switched voltage can be drawn from the fuse box or from the cigarette plug. It is also possible that it is already in the power strip of the car. Measure the power supply with a multimeter and connect the red acc. wire with this power supply point.
It is important that you have ordered a steering wheel interface with lead cable to be able to link it. If this is not the case, you can possibly purchase it from us. If you are going to connect steering wheel control to your radio, connect the steering wheel adapter between the car plug and the radio plug. In addition, a lead cable is always included with a steering adapter. This lead cable connects you between the adapter and the radio.
For example, if you have a Volkswagen or Mercedes with can bus, the plus of the reversing light does not give a constant voltage. As a result, the image can sometimes fall away or blurry become. Place a capacitor/filter between the + of the reversing light and the camera cabling. Installation and use of DAB+ If you want to use dab+ (digital radio) you can do this in 2 ways. You can use digital radio via a dab+ application. We recommend the application called: ''JUKE'' for this.
It is possible that the navigation mode in your car is not on. You can enable the navigation mode (or have it switched on) in VAGCOM. It is also possible to place a separate switching power supply on the red ACC wire of the radio. It is important that the red / ACC wire that runs via the can bus decoder is disconnected. Improve radio reception Check if the AF function in the radio menu is turned off, otherwise your radio will search for other frequencies.
Opel Solution when the radio does not fit properly in the dashboard If present, remove the iron bracket from your old radio, otherwise the new radio will enter the car under too much tension. In addition, it is important that sufficient space is freed up for getting rid of the cabling. Make sure that you do not press the screen to get the radio tight in the car, this can cause a crack.
In your phone, go to settings and go to Turn on WIFI hotspot (Note that you have not checked that only allowed devices are allowed to connect). Then go to settings at the radio and turn on the WIFI, after which you will see the name of the hotspot of your phone in the list. You can now connect the device after entering the password you see on your phone. (This can be in your phone under the heading Configure WIFI hotspot.
Free shifting to watch video while driving To be able to obtain video / image while driving, you can follow the steps below: Go via settings – car settings or car infotainment to video or brake settings. You can convert the switch here to make this (un)possible. Set standby time / direct start-up up to 60 minutes after powering off You can go via settings – car settings or car infotainment – common to the screen below. There you can set the standby time. This can be set to a maximum of 60 minutes.
2. Find the built-in CarPlay app: Zlink in the Android car player and open Zlink 1. Plug the original data cable from the Apple mobile phone into the car player and the USB port of the mobile phone 2. Waiting for connection 3.
(2). CarPlay wireless connection method (Use an iPhone to connect) 1. Turn on the Bluetooth in your car player 2. Open the setting option in Bluetooth, you can see the Bluetooth name and password in your CAR player 3. Connect your mobile phone to the Bluetooth of the car player and adjust it and return to the connection interface.
Note: If there is no phone audio music audio prompt under Bluetooth in your Car Player, click the restart Bluetooth power and try connecting again until the phone audio music audio prompt appears, indicates that the Bluetooth connection is successful 4. After the Bluetooth connection is established, the built-in CarPlay app Zlink in the car player will open automatically and wait for this connection to be made note: you may have to wait a little longer for the first connection, this is normal (3).
1. First, make sure that your Bluetooth connection is successful if your Bluetooth connection interface phone displays audio music audio, it proves that the Bluetooth connection is successful 1. Enter Android settings, network and internet, hotspot and tethering, Wi-Fi hotspot 2. Turn on the Wi-Fi hotspot, click to set up the Wi-Fi hotspot. You will see your multimedia's Wi-Fi name and Wi-Fi password.
3. When you see your phone's name appear on the connected devices, it proves that the hotspot is successfully connected 4.
5. Find Zlink and open the click connect 6.
7. The connection was successful (4). Android auto wired connection method 1. Open the main interface of the Car Player, find Zlink and click to enter 2. Connect the original data cable of your mobile phone to the mobile phone and plug the other end into the USB port of the MP5 Car Player.
Please note that when you connect the USB, the Car Player may open a prompt window, as shown in the image below. Otherwise, do not click android auto may not be able to connect 3. Waiting for connection 4.
If you want to use car play and Android auto on an Android car stereo, it is important that you have a system that has this option. It is also an option to purchase a car play/Android car dongle for your Android car radio. Use car play and Android auto with dongle If you want to use car play on the Android operating system with the car play / Android auto Dongle, then the following is important: Download the AUTOKIT application on the radio.
Step 2: Create a WIFI hotspot on the phone the first time and go to WIFI in the radio and connect to the phone. Step 3: Go to the Zlink application and connect the phone via the USB cable. Make sure your iPhone has SIRI and SEARCH turned on. Then, after a notification you get at the first startup, press wired CP and Android auto. After this you can give permission for car play and or Android auto in the phone by means of a pop up.
Copyright Nothing in this User Guide may be displayed, edited, broadcast, copied, transmitted, published, distributed, modified, posted, or posted on other websites or documents without prior written permission. All intellectual property rights of this user manual are reserved and any use thereof without the prior consent of carmultimedia.nl is strictly prohibited.
