® 2014 PATH F I N D E R OWNER’S MANUAL For your safety, read carefully and keep in this vehicle.
FOREWORD Welcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. This manual was prepared to help you understand the operation and maintenance of your vehicle so that you may enjoy many miles (kilometers) of driving pleasure. Please read through this manual before operating your vehicle.
WHEN READING THE MANUAL For descriptions specified for four-wheel drive models, a 4WD mark is placed at the beginning of the applicable sections/items. As with other vehicles with features for off-road use, failure to operate four-wheel drive models correctly may result in loss of control or an accident. Be sure to read “Driving safety precautions” in the “Starting and driving” section of this manual.
CALIFORNIA PROPOSITION 65 WARNING WARNING APD1005 Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
NISSAN CUSTOMER CARE PROGRAM NISSAN CARES . . . Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Your NISSAN dealer is always available to assist you with all your automobile sales and service needs.
Table of Contents Illustrated table of contents 0 Safety—Seats, seat belts and supplemental restraint system 1 Instruments and controls 2 Pre-driving checks and adjustments 3 Monitor, climate, audio, phone and voice recognition systems 4 Starting and driving 5 In case of emergency 6 Appearance and care 7 Maintenance and do-it-yourself 8 Technical and consumer information 9 Index 10
0 Illustrated table of contents Air bags, seat belts and child restraints . . . . . . . . . . . . . . 0-2 Exterior front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-3 Exterior rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-4 Passenger compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-5 Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-6 Engine compartment check locations . . . . .
AIR BAGS, SEAT BELTS AND CHILD RESTRAINTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Supplemental front-impact air bags (P.1-53) Occupant classification sensor (weight sensor) Seat belts (P. 1-24) Head restraints/headrests (P.1-9) Roof-mounted curtain side-impact supplemental air bag (P. 1-53) 3rd row bench seat top tether strap anchor (located on bottom of seatback) (P. 1-49 ) Folding 3rd row bench (P. 1-8) 2nd row seat top tether strap anchor (located on bottom of seatback) (P.
EXTERIOR FRONT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Front view camera (if so equipped) (P. 4-28) Engine hood (P. 8-6) Windshield wiper and washer switch, wiper blades (P. 2-28, 8-18) Windshield-washer fluid (P. 8-18) Compass display (if so equipped) (P. 2-6) Power windows (P. 2-50) Door locks, NISSAN Intelligent Key®, Remote Engine Start (if so equipped), keys (P. 3-5, 3-2, 3-20 , 3-2) Mirrors (P. 3-32) Side view camera (if so equipped) (P. 4-28) Tire pressure monitoring system (P.
EXTERIOR REAR 1. 2. 3. 4. 5. 6. 7. 8. 9. Moonroof (if so equipped)/panoramic sunshade (if so equipped) (P. 2-52, 2-54) Antenna (P.4-104) Rear window wiper and washer switch (P. 2-29) Liftgate release (power - P. 3-22, manual - P. 3-22) Rearview monitor (if so equipped) (P.4-23) Replacing bulbs (P. 8-25) Fuel-filler cap, fuel recommendation (P. 3-27, P. 9-3 ) Fuel-filler door (P. 3-27) Child safety rear door lock (P. 3-7) See the page number indicated in parentheses for operating details.
PASSENGER COMPARTMENT 1. 2. 3. 4. 5. 6. 7. 8. Glove box, Console box (P. 2-47) Map lights (P. 2-57) Storage (P. 2-43) Moonroof (if so equipped)/Panoramic sunshade (if so equipped) (P. 2-52, 2-54) Luggage hooks (P. 2-49) Cup holders (P. 2-45) Seats (P. 1-2, 1-6, 1-8) Sun visors (P. 3-31) See the page number indicated in parentheses for operating details.
INSTRUMENT PANEL 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. LIC2383 1. 2. 3. 4. Vent (P. 4-39) Headlight/fog light (if so equipped)/turn signal switch (P. 2-31) Control panel and Vehicle Information Display switches (P.2-17) Instrument brightness control (P. 2-34) 0-6 Illustrated table of contents 5. 6. 7. Driver supplemental air bag/Horn (P.1-53, P. 2-36) Meters, gauges, warning/indicator lights and Vehicle Information Display (P. 2-3, 2-10, 2-17) Twin trip odometer reset switch (P. 2-4) 19. 20.
Heated steering wheel switch (if so equipped) (P.2-38) Power inverter switch (if so equipped) (P.2-40) Power liftgate main switch (if so equipped) (P. 3-26) *: Refer to the separate Navigation System Owner’s Manual (if so equipped). See the page number indicated in parentheses for operating details.
ENGINE COMPARTMENT CHECK LOCATIONS VQ35DE engine 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Power steering fluid reservoir (P. 8-12) Engine coolant reservoir (P. 8-16) Drive belt location (P.8-16) Fuse box (P. 8-21) Engine oil filler cap (P. 8-10) Brake fluid reservoir (P. 8-12) Air cleaner (P. 8-18) Fuse box (P. 8-21) Fuse box/Fusible links (P. 8-21) Fuse box (P. 8-21) Battery (P. 8-14) Engine oil dipstick (P. 8-9) Radiator cap (P. 8-7) Windshield-washer fluid reservoir (P.
WARNING/INDICATOR LIGHTS Warning light Name Page Anti-lock Braking System (ABS) warning light 2-10 Brake warning light 2-11 or Warning light Name Supplemental air bag warning light Indicator light Page Indicator light Name Page 2-14 Slip indicator light 2-15 Name Page 2-16 Fog light indicator light (if so equipped) 2-14 Tow mode ON indicator light (if so equipped) Turn signal/hazard indicator lights 2-16 Vehicle Dynamic Control (VDC) off indicator light 2-16 2-11 Front passenger
MEMO 0-10 Illustrated table of contents
1 Safety—Seats, seat belts and supplemental restraint system Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Front manual seat adjustment (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Front power seat adjustment (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 2nd row bench seat adjustment . . . . . . . . . . . . . . . . . . 1-6 3rd row bench seat adjustment . . . . . . . . . . . . .
SEATS ● The seatback should not be reclined any more than needed for comfort. Seat belts are most effective when the passenger sits well back and straight up in the seat. If the seatback is reclined, the risk of sliding under the lap belt and being injured is increased. CAUTION When adjusting the seat positions, be sure not to contact any moving parts to avoid possible injuries and/or damage. ARS1152 WARNING ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous.
LRS2160 LRS2161 Forward and backward Reclining Pull the center of the bar up and hold it while you slide the seat forward or backward to the desired position. Release the bar to lock the seat in position. To recline the seatback, pull the lever up and lean back. To bring the seatback forward, pull the lever up and lean your body forward. Release the lever to lock the seatback in position.
The reclining feature allows adjustment of the seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit. See “Precautions on seat belt usage” later in this section. Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped and the shift lever is in P (Park). LRS2130 FRONT POWER SEAT ADJUSTMENT (if so equipped) Operating tips ● The power seat motor has an auto-reset overload protection circuit.
LRS2132 LRS2131 Seat lifter (driver’s seat) Push the front or rear end of the switch up or down to adjust the angle and height of the seat cushion. Manual (if so equipped) LRS2270 Power (if so equipped) Lumbar support (driver’s seat) The lumbar support feature provides adjustable lower back support to the driver. Move the lever up or down (manual) or push the front or back end of the switch (power) to adjust the seat lumbar area.
The recline feature allows adjustment of the seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit (see “Precautions on seat belt usage” later in this section). Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped and the shift lever is in P (Park). WARNING ● After adjustment, gently rock in the seat to make sure it is securely locked.
CAUTION ● Be careful not to pinch your hand or foot or bump your head when operating the walk-in seat. ● Do not drive with the 2nd row seat tipped up. ● Be careful not to allow the 2nd row seat to pinch, hit any part of your body or other people when operating the 2nd row seat. Make sure the seat path is clear of all objects before moving the seat. To enter the 3rd row from outside the vehicle, lift up on the seatback lever located on the upper outboard side of the seatback on the 2nd row bench seat.
The recline feature allows adjustment of the seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit. See “Precautions on seat belt usage” later in this section. Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped and the shift lever is in P (Park). WARNING When returning the seat to its original position, confirm that the seat and seatback are locked properly.
1ST ROW HEAD RESTRAINTS/ HEADRESTS WARNING ● Head restraints/headrests supplement the other vehicle safety systems. They may provide additional protection against injury in certain rear end collisions. Adjust the head restraints/headrests properly, as specified in this section. Check the adjustment after someone else uses the seat. Do not attach anything to the head restraint/headrest stalks. Do not use the seat if the head restraint/headrest has been removed.
● Adjustable head restraints/headrests have multiple notches along the stalk to lock them in a desired adjustment position. ● The non-adjustable head restraints/headrests have single locking notches to secure them to the seat frame. ● Proper Adjustment: – For the adjustable type, align the head restraint/headrest so the center of your ear is approximately level with the center of the head restraint/headrest.
Use the following procedure to remove the head restraints/headrests 1. Pull the head restraint/headrest up to the highest position. 2. Push and hold the lock knob. 3. Remove the head restraint/headrest from the seat. 4. Store the head restraint/headrest properly in a secure place so it is not loose in the vehicle. LRS2302 Removable (without Dual head restraint/headrest DVD system only) CAUTION Do not remove head restraint/headrest from vehicles equipped with Dual head restraint/headrest DVD system.
WRS0134 For adjustable head restraint/headrest Adjust the head restraint/headrest so the center is level with the center of your ears. If your ear position is still higher than the recommended alignment, place the head restraint/headrest at the highest position.
2ND ROW HEAD RESTRAINTS/ HEADRESTS WARNING LRS2306 To lower, push and hold the lock knob and push the head restraint/headrest down. Make sure the head restraint/headrest is positioned so the lock knob is engaged in the notch before riding in that designated seating position. Head restraints/headrests supplement the other vehicle safety systems. They may provide additional protection against injury in certain rear end collisions. Adjust the head restraints/headrests properly, as specified in this section.
● Adjustable head restraints/headrests have multiple notches along the stalk to lock them in a desired adjustment position. ● The non-adjustable head restraints/headrests have single locking notches to secure them to the seat frame. ● Proper Adjustment: – For the adjustable type, align the head restraint/headrest so the center of your ear is approximately level with the center of the head restraint/headrest.
5. Reinstall and properly adjust the head restraint/headrest before an occupant uses the seating position. LRS2302 Removable Use the following procedure to remove the head restraints/headrests 1. Pull the head restraint/headrest up to the highest position. 2. Push and hold the lock knob. 3. Remove the head restraint/headrest from the seat. 4. Store the head restraint/headrest properly in a secure place so it is not loose in the vehicle. LRS2303 Install 1.
WRS0134 For adjustable head restraint/headrest Adjust the head restraint/headrest so the center is level with the center of your ears. If your ear position is still higher than the recommended alignment, place the head restraint/headrest at the highest position.
3RD ROW HEAD RESTRAINTS/ HEADRESTS WARNING LRS2306 To lower, push and hold the lock knob and push the head restraint/headrest down. Make sure the head restraint/headrest is positioned so the lock knob is engaged in the notch before riding in that designated seating position. Head restraints/headrests supplement the other vehicle safety systems. They may provide additional protection against injury in certain rear end collisions. Adjust the head restraints/headrests properly, as specified in this section.
● Adjustable head restraints/headrests have multiple notches along the stalk to lock them in a desired adjustment position. ● The non-adjustable head restraints/headrests have single locking notches to secure them to the seat frame. ● Proper Adjustment: – For the adjustable type, align the head restraint/headrest so the center of your ear is approximately level with the center of the head restraint/headrest.
5. Reinstall and properly adjust the head restraint/headrest before an occupant uses the seating position. LRS2311 Removable Use the following procedure to remove the head restraints/headrests 1. Pull the head restraint/headrest up to the highest position. 2. Push and hold the lock knobs. 3. Remove the head restraint/headrest from the seat. 4. Store the head restraint/headrest properly in a secure place so it is not loose in the vehicle. LRS2312 Install 1.
WRS0134 For adjustable head restraint/headrest Adjust the head restraint/headrest so the center is level with the center of your ears. If your ear position is still higher than the recommended alignment, place the head restraint/headrest at the highest position.
WARNING When the seat is returned to the normal seating position, the head restraints/headrests must be returned to the upright position to properly protect vehicle occupants. FLEXIBLE SEATING WARNING LRS2306 To lower, push and hold the lock knob and push the head restraint/headrest down. Make sure the head restraint/headrest is positioned so the lock knob is engaged in the notch before riding in that designated seating position.
2. Stow the 2nd row seat belts in the seat belt hooks found on the sides of the vehicle. ● Head restraints/headrests should be adjusted properly as they may provide significant protection against injury in an accident. Always replace and adjust them properly if they have been removed for any reason. 3. Lift up on the recline lever on the side of the outboard seats to fold the seatbacks flat. 4. To return the 2nd row bench seats to a seating position, push up on the seatback until it latches in place.
To return the 3rd row seats to a seating position: 3 to raise each seat1. Use the pull straps 䊊 back. Pull back until the seatback latches into position. Make sure to properly raise each seatback to an upright and secured position. 2. Do not use the pull strap to return the head restraint/headrest to the upright position. Pull back on the head restraint/headrest until it latches in the upright position.
SEAT BELTS SSS0136 PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly adjusted and you are sitting upright and well back in your seat with both feet on the floor, your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced. NISSAN strongly encourages you and all of your passengers to buckle up every time you drive, even if your seating position includes a supplemental air bag. Most U.S.
SSS0134 WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly restrained in the rear seat and, if appropriate, in a child restraint. SSS0016 WARNING ● The seat belt should be properly adjusted to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident. Serious injury or death can occur if the seat belt is not worn properly.
● Be sure the seat belt tongue is securely fastened to the proper buckle. ● Do not wear the seat belt inside out or twisted. Doing so may reduce its effectiveness. ● Do not allow more than one person to use the same seat belt. ● Never carry more people in the vehicle than there are seat belts. SSS0014 WARNING ● Always route the shoulder belt over your shoulder and across your chest. Never put the belt behind your back, under your arm or across your neck.
PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts. The seat belt should be worn snug and always position the lap belt as low as possible around the hips, not the waist. Place the shoulder belt over your shoulder and across your chest. Never run the lap/shoulder belt over your abdominal area. Contact your doctor for specific recommendations. INJURED PERSONS NISSAN recommends that injured persons use seat belts. Check with your doctor for specific recommendations.
The Emergency Locking Retractor (ELR) mode allows the seat belt to extend and retract to allow the driver and passengers some freedom of movement in the seat. The ELR locks the seat belt when the vehicle slows down rapidly or during certain impacts. The Automatic Locking Retractor (ALR) mode (child restraint mode) locks the seat belt for child restraint installation. WRS0137 2 䊊 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage.
To increase your confidence in the seat belts, check the operation as follows: ● Grasp the shoulder belt and pull forward quickly. The retractor should lock and restrict further belt movement. If the retractor does not lock during this check or if you have any questions about seat belt operation, see a NISSAN dealer. WRS0139 Unfastening the seat belts 1 䊊 To unfasten the seat belt, press the button on the buckle. The seat belt automatically retracts.
Seat belt extenders are available for the: WARNING ● Driver and front passenger seating position ● After adjustment, release the adjustment button and try to move the shoulder belt anchor up and down to make sure it is securely fixed in position. ● 2nd and 3rd row seating position See a NISSAN dealer for assistance with purchasing an extender if an extender is required. ● The shoulder belt anchor height should be adjusted to the position best for you.
CHILD SAFETY SEAT BELT MAINTENANCE ● To clean the seat belt webbing, apply a mild soap solution or any solution recommended for cleaning upholstery or carpet. Then wipe with a cloth and allow the seat belts to dry in the shade. Do not allow the seat belts to retract until they are completely dry. ● If dirt builds up in the shoulder belt guide of the seat belt anchors, the seat belts may retract slowly. Wipe the shoulder belt guide with a clean, dry cloth.
All U.S. states and Canadian provinces or territories require the use of approved child restraints for infants and small children. See “Child restraints” later in this section. A child restraint may be secured in the vehicle by using either the LATCH (Lower Anchor and Tethers for CHildren) system or with the vehicle seat belt. See “Child restraints” later in this section for more information. NISSAN recommends that all pre-teens and children be restrained in the rear seat.
CHILD RESTRAINTS – Infants and children should never be held on anyone’s lap. Even the strongest adult cannot resist the forces of a collision. – Do not put a seat belt around both a child and another passenger.
– Child restraint anchor points are designed to withstand loads from child restraints that are properly fitted. – Never use the anchor points for adult seat belts or harnesses. – A child restraint with a top tether strap should not be used in the front passenger seat. – Keep seatbacks as upright as possible after fitting the child restraint. – Infants and children should always be placed in an appropriate child restraint while in the vehicle.
The LATCH lower anchor points are provided to install child restraints in the following positions only: ● 2nd row bench seat – outboard seating positions LATCH lower anchor WARNING LRS2137 LATCH system lower anchor locations bench seat LATCH (Lower Anchors and Tethers for CHildren) SYSTEM Your vehicle is equipped with special anchor points that are used with LATCH (Lower Anchors and Tethers for CHildren) system compatible child restraints.
WRS0700 LATCH lower anchor location LRS2146 LATCH label locations 2nd row bench LATCH lower anchor location The LATCH lower anchors are located at the rear of the seat cushion near the seatback. A label is attached to the seatback to help you locate the LATCH lower anchors.
Top tether anchor WARNING Do not allow cargo to contact the top tether strap when it is attached to the top tether anchor. Properly secure the cargo so it does not contact the top tether strap. Cargo that is not properly secured or cargo that contacts the top tether strap may damage it during a collision. A child could be seriously injured or killed in a collision if the top tether strap is damaged.
REAR-FACING CHILD RESTRAINT INSTALLATION USING LATCH Refer to all Warnings and Cautions in the “Child Safety” and “Child Restraint” sections before installing a child restraint. Follow these steps to install a rear-facing child restraint in the 2nd row seats using the LATCH system: WARNING LRS2291 3rd row bench seat Top tether anchor point locations Anchor points are located in the following locations: ● 2nd row bench on the bottom of the seatback in the seating positions shown.
WRS0802 Rear-facing rigid-mounted – step 2 LRS0673 Rear-facing – step 3 3. For child restraints that are equipped with webbing-mounted attachments, remove any additional slack from the anchor attachments. Press downward and rearward firmly in the center of the child restraint with your hand to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments. LRS0674 Rear-facing – step 4 4.
5. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 2 through 4. WARNING The three-point seat belt with Automatic Locking Retractor (ALR) must be used when installing a child restraint. Failure to use the ALR mode will result in the child restraint not being properly secured. The restraint could tip over or be loose and cause injury to a child in a sudden stop or collision.
WRS0256 Rear-facing – step 1 Refer to all Warnings and Cautions in the “Child safety” and “Child restraints” sections before installing a child restraint. Follow these steps to install a rear-facing child restraint using the vehicle seat belts in the rear seats: WRS0761 Rear-facing – step 2 2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing.
LRS0670 Rear-facing – step 4 4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. WRS0762 Rear-facing – step 5 5. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seatback while pulling up on the seat belt. 1-42 Safety—Seats, seat belts and supplemental restraint system WRS0763 Rear-facing – step 6 6.
7. Check to make sure that the child restraint is properly secured prior to each use. If the seat belt is not locked, repeat steps 1 through 6. After the child restraint is removed and the seat belt fully retracted, the ALR mode (child restraint mode) is canceled. FORWARD-FACING CHILD RESTRAINT INSTALLATION USING LATCH Refer to all Warnings and Cautions in the “Child Safety” and “Child Restraints” sections before installing a child restraint.
If the seating position does not have an adjustable head restraint/headrest and it is interfering with the proper child restraint fit, try another seating position or a different child restraint. LRS0671 Forward-facing – step 4 4. For child restraints that are equipped with webbing-mounted attachments, remove any additional slack from the anchor attachments.
7. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 3 through 6. 2. Position the child restraint on the seat. Always follow the child restraint manufacturer’s instructions. The back of the child restraint should be secured against the vehicle seatback.
WRS0680 Forward-facing – step 3 3. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing. If the child restraint is equipped with a top tether strap, route the top tether strap and secure the tether strap to the tether anchor point (rear seat installation only). See “Installing top tether strap” in this section.
9. Check to make sure the child restraint is properly secured prior to each use. If the seat belt is not locked, repeat steps 2 through 8. WRS0681 Forward-facing – step 6 6. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while pulling up on the seat belt. 7. Tighten the tether strap according to the manufacturer’s instructions to remove any slack.
head restraint/headrest is removed, store it in a secure place. Be sure to reinstall the head restraint/headrest when the child restraint is removed. See “Head restraint/headrest adjustment” in this section for head restraint/headrest adjustment, removal and installation information. CENTER SEATING POSITION LRS0865 Forward-facing – step 10 10. If the child restraint is installed in the front passenger seat, place the ignition switch in the ON position. The front passenger air bag should illuminate.
If you have any questions when installing a top tether strap, consult your NISSAN dealer for details. The passenger side of the 3rd row bench seat is the seating position that can use a top tether strap. First, secure the child restraint with the seat belt, as applicable. 1 to the out1. Position the top tether strap 䊊 board side of the head restraint/headrest as shown. 2. Secure the tether strap to the tether anchor 2 on the bottom of the seatback point 䊊 behind the child restraint.
BOOSTER SEATS Precautions on booster seats WARNING If a booster seat and seat belt are not used properly, the risk of a child being injured in a sudden stop or collision greatly increases: – Make sure the shoulder portion of the belt is away from the child’s face and neck and the lap portion of the belt does not cross the stomach. – Make sure the shoulder belt is not behind the child or under the child’s arm. – A booster seat must only be installed in a seating position that has a lap/shoulder belt.
● Make sure the child’s head will be properly supported by the booster seat or vehicle seat. The seatback must be at or above the center of the child’s ears. For example, if a 1 is chosen, the low back booster seat 䊊 vehicle seatback must be at or above the center of the child’s ears. If the seatback is lower than the center of the child’s ears, a 2 should be used. high back booster seat 䊊 LRS0464 Booster seats of various sizes are offered by several manufacturers.
If the seating position does not have an adjustable head restraint/headrest and it is interfering with the proper booster seat fit, try another seating position or a different booster seat. 4. Position the lap portion of the seat belt low and snug on the child’s hips. Be sure to follow the booster seat manufacturer’s instructions for adjusting the seat belt routing. LRS0454 WRS0699 1. If you must install a booster seat in the front seat, move the seat to the rearmost position.
SUPPLEMENTAL RESTRAINT SYSTEM PRECAUTIONS ON SUPPLEMENTAL RESTRAINT SYSTEM This Supplemental Restraint System (SRS) section contains important information concerning the following systems: ● Driver and passenger supplemental frontimpact air bag (NISSAN Advanced Air Bag System) ● Front seat-mounted side-impact supplemental air bag LRS0865 7. If the booster seat is installed in the front passenger seat, place the ignition switch in the ON position.
● The driver and front passenger seat belt buckles are equipped with sensors that detect if the seat belts are fastened. The Advanced Air Bag System monitors the severity of a collision and seat belt usage then inflates the air bags as needed. Failure to properly wear seat belts can increase the risk or severity of injury in an accident. WRS0031 WARNING ● The front air bags ordinarily will not inflate in the event of a side impact, rear impact, rollover, or lower severity frontal collision.
ARS1133 ARS1041 WARNING ● Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations.
ARS1042 1-56 Safety—Seats, seat belts and supplemental restraint system ARS1043 ARS1044
ARS1045 ARS1046 WRS0431 ● Children may be severely injured or killed when the front air bags, side air bags or curtain air bags inflate if they are not properly restrained. Pre-teens and children should be properly restrained in the rear seat, if possible. Front seat-mounted side-impact supplemental air bags and roof-mounted curtain side-impact supplemental air bags: WARNING ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat.
WARNING SSS0162 1-58 Safety—Seats, seat belts and supplemental restraint system SSS0159 ● The seat belts, the side air bags and curtain air bags are most effective when you are sitting well back and upright in the seat with both feet on the floor. The side air bag and curtain air bag inflate with great force. Do not allow anyone to place their hand, leg or face near the side air bag on the side of the seatback of the front seat or near the side roof rails.
WARNING ● When sitting in the 2nd row rear seat, do not hold onto the seatback of the front seat. If the side air bag inflates, you may be seriously injured. Be especially careful with children, who should always be properly restrained. Some examples of dangerous riding positions are shown in the illustrations ● Do not use seat covers on the front seatbacks. They may interfere with side air bag inflation.
1. Supplemental front-impact air bag modules 2. Air bag Control Unit (ACU) 3. Occupant classification sensor (weight sensor) 4. Front seat-mounted side-impact supplemental air bag modules 5. Roof-mounted curtain side-impact and rollover supplemental air bags 6. Roof-mounted curtain side-impact and rollover supplemental air bag inflators 7. Satellite sensors 8. Seat belt with pretensioner 9. Pressure sensors in door (driver’s side shown; passenger side similar) 10.
● Do not place heavy loads heavier than 2.2 lb (1 kg) on the seatback, head restraint/headrest or in the seatback pocket. ● Do not store luggage behind the seat that can press into the seatback. ● Do not position the front passenger seat so it contacts the rear seat. If the front seat does contact the rear seat, the air bag system may determine a sensor malfunction has occurred and the front passenger air bag status light may illuminate and the supplemental air bag warning light may flash.
When a front air bag inflates, a fairly loud noise may be heard, followed by the release of smoke. This smoke is not harmful and does not indicate a fire. Care should be taken to not inhale it, as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly. After placing the ignition switch in the ON position, the supplemental air bag warning light illuminates.
Status light The front passenger air bag status light is located near the radio controls. After the ignition switch is placed in the ⬙ON⬙ position, the front passenger air bag status light on the instrument panel illuminates for about 7 seconds and then turns off or remains illuminated depending on the front passenger seat occupied status. The light operates as follows: is ● Unoccupied passenger’s seat: The OFF and the front passenger air bag is OFF and will not inflate in a crash.
Using the passenger air bag status light, you can monitor when the front passenger air bag is automatically turned OFF with the seat occupied. The light will not illuminate when the front passenger seat is unoccupied. If an adult occupant is in the seat but the passenger air bag status light is illuminated (indicating that the air bag is OFF), it could be that the person is a small adult, or is not sitting on the seat properly or not using the seat belt properly.
● Modifying or tampering with the front passenger seat may result in serious personal injury. For example, do not change the front seats by placing material on the seat cushion or by installing additional trim material, such as seat covers, on the seat that are not specifically designed to assure proper air bag operation. Additionally, do not stow any objects under the front passenger seat or the seat cushion and seatback.
They are designed to inflate on the side where the vehicle is impacted. They may not inflate in certain side collisions. Curtain air bags are also designed to inflate in certain types of rollover collisions or near rollovers. As a result, certain vehicle movements (for example, during severe off roading) may cause the curtain air bags to inflate. Vehicle damage (or lack of it) is not always an indication of proper side air bag and curtain air bag operation.
● Tampering with the side air bag system may result in serious personal injury. For example, do not change the front seats by placing material near the seatbacks or by installing additional trim material, such as seat covers, around the side air bag. ● Work around and on the side air bag and curtain air bag systems should be done by a NISSAN dealer. Installation of electrical equipment should also be done by a NISSAN dealer. The SRS wiring harnesses* should not be modified or disconnected.
When selling your vehicle, we request that you inform the buyer about the pretensioner system and guide the buyer to the appropriate sections in this Owner’s Manual. LRS2158 1. SRS Air Bag Warning Labels The warning labels are located on the surface of the sun visor. SUPPLEMENTAL AIR BAG WARNING LABELS Warning labels about the supplemental frontimpact air bag system are placed in the vehicle as shown in the illustration.
If any of the following conditions occur, the front air bag, side air bag, curtain air bag and pretensioner systems need servicing: ● The supplemental air bag warning light remains on after approximately 7 seconds. ● The supplemental air bag warning light flashes intermittently. ● The supplemental air bag warning light does not come on at all. Under these conditions, the front air bag, side air bag, curtain air bag or pretensioner systems may not operate properly. They must be checked and repaired.
2 Instruments and controls Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Meters and gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Speedometer and odometer . . . . . . . . . . . . . . . . . . . . . 2-4 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Engine coolant temperature gauge . . . . . . . . . . . . . . . 2-5 Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seatback pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44 Sunglasses holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44 Cup holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45 Glove box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47 Console box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-47 Storage tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. LIC2383 1. 2. 3. 4. Vent (P. 4-39) Headlight/fog light (if so equipped)/turn signal switch (P. 2-31) Control panel and Vehicle Information Display switches (P.2-17) Instrument brightness control (P. 2-34) 2-2 Instruments and controls 5. 6. 7. Driver supplemental air bag/Horn (P.1-53, P. 2-36) Meters, gauges, warning/indicator lights and Vehicle Information Display (P. 2-3, 2-10, 2-17) Twin trip odometer reset switch (P. 2-4) 19. 20.
METERS AND GAUGES Heated steering wheel switch (if so equipped) (P.2-38) Power inverter switch (if so equipped) (P.2-40) Power liftgate main switch (if so equipped) (P. 3-26) *: Refer to the separate Navigation System Owner’s Manual (if so equipped). See the page number indicated in parentheses for operating details. LIC2254 1. 2. 3. 4. 5. 6. Tachometer Warning/indicator lights Vehicle Information Display Speedometer Fuel gauge Odometer/Twin trip odometer 7.
LIC2255 SPEEDOMETER AND ODOMETER LIC2234 Changing the display: The speedometer indicates vehicle speed. 3 switch on the right Pushing the TRIP RESET 䊊 of the instrument panel to change the display as follows: Odometer/Twin trip odometer Trip Speedometer 1 and the twin trip odometer 䊊 2 The odometer 䊊 are displayed below the Vehicle Information Display when the ignition switch is placed in the ON position. The odometer records the total distance the vehicle has been driven.
CAUTION If the gauge indicates coolant temperature near the hot (H) end of the normal range, reduce vehicle speed to decrease temperature. If the gauge is over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle may seriously damage the engine. See “If your vehicle overheats” in the “In case of emergency” section for immediate action required.
COMPASS DISPLAY (if so equipped) The indicates that the fuel-filler door is located on the driver’s side of the vehicle. CAUTION ● If the vehicle runs out of fuel, the Malfunction Indicator Light (MIL) may come on. Refuel as soon as possible. light After a few driving trips. the should turn off. If the light remains on after a few driving trips, have the vehicle inspected by a NISSAN dealer. ● For additional information, see “Malfunction Indicator Light (MIL)” later in this section.
WIC0904 Type A COMPASS DISPLAY Push the or button for about 1 second when the ignition switch is placed in the ON position to toggle the compass direction display 1 on or off. The display will indicate the direction 䊊 that the vehicle is heading. LIC1487 Type B If the display reads “C”, calibrate the compass by driving the vehicle in three complete circles at less than 5 MPH (8 km/h). You can also calibrate the compass by driving your vehicle on your everyday route.
Zone variation change procedure The difference between magnetic north and geographical north is known as variance. In some areas, this difference can sometimes be great enough to cause false compass readings. Follow these instructions to set the variance for your particular location if this happens: button for about 1. Press and hold the 11 seconds or the button for about 8 seconds. The current zone number will appear in the display. Release the button. 2. Find your current location on the zone map.
Inaccurate compass direction: The compass display is equipped with automatic correction function. If the correct direction is not shown, follow this procedure. 1. With the display turned on, press and hold button for about 13 seconds or the the for about 10 seconds. The “C” icon in the compass display will illuminate. 2. Calibrate the compass by driving the vehicle in three complete circles at a maximum speed of 5 MPH (8 km/h). 3. After completing the circles, the display should return to normal.
WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS Anti-lock Braking System (ABS) warning light Supplemental air bag warning light Slip indicator light or Front fog light indicator light (if so equipped) Tow mode ON indicator light (if so equipped) Charge warning light Front passenger air bag status light Turn signal/hazard indicator lights Low tire pressure warning light High beam indicator light (blue) Vehicle Dynamic Control (VDC) off indicator light Master warning light Malfunction Indicator Li
If the ABS light comes on while the engine is running, it may indicate the anti-lock braking system is not functioning properly. Have the system checked by a NISSAN dealer. If an ABS malfunction occurs, the anti-lock function is turned off. The brake system then operates normally, but without anti-lock assistance. See “Brake system” in the “Starting and driving” section. or Brake warning light This light functions for both the parking brake and the foot brake systems.
The low tire pressure warning light warns of low tire pressure or indicates that the TPMS is not functioning properly. After the ignition switch is placed in the ON position, this light illuminates for about 1 second and turns off. Low tire pressure warning: If the vehicle is being driven with low tire pressure, the warning light will illuminate. A “Tire Press Low - Add Air” warning also appears in the vehicle information display.
● When a spare tire is mounted or a wheel is replaced tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. ● Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.
Refer to “Seat belts” in the “Safety—Seats, seat belts and supplemental restraint system” section for precautions on seat belt usage. Supplemental air bag warning light When the ignition switch is placed in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational.
If this indicator light comes on steady for 20 seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control system inspection/maintenance test. See “Readiness for inspection/maintenance (I/M) test” in the “Technical and consumer information” section of this manual.
The light will blink for a few seconds after the VDC system stops limiting wheel spin. indicator light also comes on when The you place the ignition switch in the ON position. The light will turn off after approximately 2 seconds if the system is operational. If the light does not come on have the system checked by a NISSAN dealer. Tow mode ON indicator light (if so equipped) This light comes on when the tow mode function is ON.
VEHICLE INFORMATION DISPLAY 3. — go back to the previous menu The ENTER and buttons also control audio and control panel functions. For additional information see, “Steering wheel switch for audio control” in “Monitor, climate, audio, phone and voice recognition systems” section.
SETTINGS Vehicle Settings Light Off Delay (if so equipped) The setting mode allows you to change the information displayed in the vehicle information display: The vehicle settings allows the customer to change settings for interior lights, intelligent key settings, unlock settings and other vehicle settings. The duration of the automatic headlights can be changed from 0 to 180 seconds. From the Vehicle Settings menu, select “Light Off Delay”. Use the ENTER button to change the duration.
operation is performed once. From the Vehicle Settings menu, select “Selective Unlock”. Use the ENTER button to activate this function. Auto Door Unlock The auto door unlock function automatically unlocks all the doors when the shift lever is placed in the P (Park) position. From the Vehicle Settings menu, select “Auto Door Unlock”. Use the ENTER button to enable/disable this function.
From the “Main Menu Selection” select “Fuel Economy” to display in the vehicle information display when the ignition is placed in the ON position. 3. Select “Maintenance” using the tons and press ENTER. Service This indicator appears when the customer set distance comes for changing the engine oil and filter. You can set or reset the distance for checking or replacing these items. For scheduled maintenance items and intervals, see your “NISSAN Service and Maintenance Guide.
WARNING The tire replacement indicator is not a substitute for regular tire checks, including tire pressure checks. See “Changing Wheels and Tires” in “Maintenance & DoIt-Yourself” section. Many factors including tire inflation, alignment, driving habits and road conditions affect tire wear and when tires should be replaced. Setting the tire replacement indicator for a certain driving distance does not mean your tires will last that long.
Use the , , and the ENTER buttons to select and change the units of the vehicle information display. The units of the navigation screen can be changed independently of the vehicle information display. For vehicles equipped with Navigation, see “System” in the “Monitor, climate, audio, phone and voice recognition systems” section of this manual.
LIC2557 VEHICLE INFORMATION DISPLAY WARNINGS AND INDICATORS 1. No Key Detected 4. Push ignition to OFF 5. Key battery low 2. Key ID Incorrect 6. Engine start operation for Intelligent Key system 3. Shift to Park 7. Release parking brake 8. Low Fuel 9. Low Washer Fluid 10. Door Open 11.
12. Timer Alert – Time for a driver break? 13. Low Outside Temperature 14. Power will turn off to save the battery 15. CVT Error: See Owner’s Manual 16. Reminder: Turn OFF headlights 17. Low Oil Pressure 18. Key Registration Complete 19. Tire Pressure Low - Add Air (if so equipped) 20. TPMS Error 21. Remote Start (if so equipped) 22. Loose Fuel Cap 23.
Low Washer Fluid Power will turn off to save the battery Key registration complete This warning illuminates when the windshieldwasher fluid is at a low level. Add windshieldwasher fluid as necessary. See “Windshieldwasher fluid” in the “Maintenance and do-ityourself” section of this manual. This warning appears in message area of the vehicle information display after a period of time if the shift lever has not moved from the P (Park) position.
SECURITY SYSTEMS Push to start (if so equipped) The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Always secure your vehicle even if parking for a brief period. Never leave your Intelligent Key in the vehicle, and always lock the vehicle when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible.
4. Confirm that the security indicator light comes on. The security light stays on for about 30 seconds. The vehicle security system is now pre-armed. After about 30 seconds the vehicle security system automatically shifts into the armed phase. The security light begins to flash once every 3 seconds. If, during the 30-second pre-arm time period, the driver’s door is unlocked by the key or the keyfob, or the ignition switch is placed in the ACC or ON position, the system will not arm.
WINDSHIELD WIPER AND WASHER SWITCH WARNING In freezing temperatures the washer solution may freeze on the window and obscure your vision which may lead to an accident. Warm the window with the defroster before you wash the window. CAUTION ● Do not operate the washer continuously for more than 30 seconds. ● Do not operate the washer if the reservoir tank is empty. LIC0474 Security indicator light The security indicator light blinks whenever the ignition switch is placed in the OFF, LOCK or ACC position.
REAR WINDOW WIPER AND WASHER SWITCH 2 䊊 3 䊊 Low (LO) — continuous low speed operation High (HI) — continuous high speed operation 4 to have one sweep operaPush the lever up 䊊 tion (MIST) of the wiper. 5 to operate the Pull the lever toward you 䊊 washer. The wiper will also operate several times. WARNING In freezing temperatures the washer solution may freeze on the window and obscure your vision. Warm the rear window with the defroster before you wash the rear window.
3 to operate the Push the switch forward 䊊 washer. Then the wiper will also operate several times. REAR WINDOW AND OUTSIDE MIRROR (if so equipped) DEFROSTER SWITCH WIC1554 LIC2398 If the rear window wiper operation is interrupted by snow etc., the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to OFF and remove the snow etc. on and around the wiper arms. After about 1 minute, turn the switch ON again to operate the wiper.
HEADLIGHT AND TURN SIGNAL SWITCH LIC1388 Type B WIC1435 Type A WIC1436 Type B NOTE: The top and bottom few rows of wires on the rear window are not part of the rear window defroster system. These wires make up the antenna for the audio system.
CAUTION Use the headlights with the engine running to avoid discharging the vehicle battery. WIC1510 Type C HEADLIGHT CONTROL SWITCH Lighting 1 䊊 2 䊊 When turning the switch to the position, the front parking, tail, license plate and instrument panel lights come on. When turning the switch to the position, the headlights come on and all the other lights remain on. 2-32 Instruments and controls LIC2351 Autolight system The autolight system allows the headlights to turn on and off automatically.
NOTE: Autolight activation sensitivity and the time delay for autolight shutoff can be adjusted. See “Vehicle information display” in this section. To turn on the autolight system: 1. Turn the headlight switch to the AUTO posi1 . tion 䊊 2. Turn the ignition switch to ON. 3. The autolight system automatically turns the headlights on and off. Initially, if the ignition switch is turned OFF and a door is opened and left open, the headlights remain ON for a period of time.
DAYTIME RUNNING LIGHT SYSTEM (Canada only) The daytime running lights automatically illuminate when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the OFF position position. Turn the headlight switch or in the to the position for full illumination when driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illuminate.
The headlights must be on and the low beams selected for the fog lights to operate. The fog lights automatically turn off when the high beam headlights are selected. WIC1440 Type A WIC1513 Type B FOG LIGHT SWITCH (if so equipped) To turn the fog lights on, turn the headlight switch to the position, then turn the fog light switch to the position. To turn the fog lights on with the headlight switch in the AUTO position, the headlights must be on, posithen turn the fog light switch to the tion.
HORN HEATED SEATS (if so equipped) WARNING Do not use or allow occupants to use the seat heater if you or the occupants cannot monitor elevated seat temperatures or have an inability to feel pain in body parts that contact the seat. Use of the seat heater by such people could result in serious injury. CAUTION LIC2227 To sound the horn, push near the horn icon of the steering wheel. WARNING Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system.
HEATED REAR SEATS (if so equipped) ● When cleaning the seat, never use gasoline, benzine, thinner, or any similar materials. ● If any malfunctions are found or the heated seat does not operate, turn the switch off and have the system checked by your NISSAN dealer. WARNING Do not use or allow occupants to use the seat heater if you or the occupants cannot monitor elevated seat temperatures or have an inability to feel pain in body parts that contact the seat.
HEATED STEERING WHEEL (if so equipped) 3. When the seat is warmed or before you leave the vehicle, be sure to turn the switch off. LIC1543 LIC0421 The rear seats are warmed by built-in heaters. The switches are located on the rear of the front center console and can be operated independently of each other. The heated steering wheel system is designed to operate only when the surface temperature of the steering wheel is below approximately 68°F (20°C). 1. Start the engine. 2.
CLIMATE CONTROLLED SEAT SWITCH (if so equipped) NOTE: mately 60 seconds after turning the switch on or selecting the desired temperature. The heated steering wheel switch is equipped with a 30 minute timer. After the switch has been activated for 30 minutes, the system will automatically turn off. If the surface temperature of the steering wheel is above 68°F (20°C) when the switch is turned on, the system will not heat the steering wheel. This is not a malfunction. 4.
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH POWER INVERTER SWITCH (if so equipped) ● Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated. ● Do not place anything hard or heavy on the seat or pierce it with a pin or similar objects. This may result in damage to the climate controlled seat. ● Any liquid spilled on the seat should be removed immediately with a dry cloth ● The climate controlled seat has an air filter.
TOW MODE SWITCH POWER OUTLETS For additional information, refer to “Tow mode” in the “Technical and consumer information” section later in this manual. LIC2391 LIC2390 Tow mode should be used when pulling a heavy trailer or hauling a heavy load. Driving the vehicle in the tow mode with no trailer/load or light trailer/light load will not cause any damage. However, fuel economy may be reduced, and the transmission/engine driving characteristics may feel unusual.
● Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may open. ● When not in use, be sure to close the cap. Do not allow water or any other liquid to contact the outlet. LIC2408 Center Console CAUTION ● The outlet and plug may be hot during or immediately after use. ● Only certain power outlets are designed for use with a cigarette lighter unit. Do not use any other power outlet for an accessory lighter.
STORAGE ● Avoid using power outlets when the air conditioner, headlights or rear window defroster is on. ● Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF. ● Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may open. LIC2407 2nd Row 120V OUTLET (if so equipped) ● When not in use, be sure to close the cap. Do not allow water or any other liquid to contact the outlet.
CAUTION ● Do not use for anything other than sunglasses. ● Do not leave sunglasses in the sunglasses holder while parking in direct sunlight. The heat may damage the sunglasses. LIC2232 LIC2312 SEATBACK POCKETS SUNGLASSES HOLDER There are two seatback pockets located on the back of the driver and passenger seats. The pockets can be used to store maps. To open the sunglasses holder, push and release 1 . 䊊 Only store one pair of sunglasses in the holder.
LIC2387 Front console CUP HOLDERS LIC2395 Rear door LIC2212 Bench seat CAUTION Do not recline the rear seatback when you use the cup holders on the rear armrest. Doing so may cause the beverages to spill over, and if they are hot, they may scald the passengers.
LIC2242 3rd row CAUTION LIC2393 Bottle holder — front CAUTION ● Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger. ● Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident. ● Use only soft cups in the cup holder. Hard objects can injure you in an accident.
LIC2243 WIC1120 LIC0702 GLOVE BOX CONSOLE BOX Lower half Open the glove box by pulling the handle. Use the 1 or unlocking 䊊 2 the master key when locking 䊊 glove box. Upper half Pull up on the passenger’s side latch to open the lower half of the console box. A power outlet is located inside the console box and there is storage for compact discs. WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.
WARNING ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury. ● Use suitable ropes and hooks to secure cargo. LIC2214 STORAGE TRAY WARNING Do not place sharp objects in the trays to help prevent injury in an accident or sudden stop.
Do not apply any load directly to the roof side rails. Cross bars must be installed before applying load/cargo/luggage to the roof of the vehicle. Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and rear). The GVWR and GAWR are located on the F.M.V.S.S. or C.V.M.S.S. certification label (located on the driver’s door pillar).
WINDOWS ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury. CAUTION Always install the cross bars onto the roof side rails before loading cargo of any kind. Loading cargo directly onto the roof side rails or the vehicle’s roof may cause vehicle damage. POWER WINDOWS WARNING ● Make sure that all passengers have their hands, etc.
Driver’s side power window switch The driver’s side control panel is equipped with switches to open or close all of the windows. To open a window, push the switch to the first detent and continue to hold down until the desired window position is reached. To close a window, pull the switch to the first detent and continue to hold up until the desired window position is reached. Locking passengers’ windows When the window lock button is depressed, only the driver’s side window can be opened or closed.
MOONROOF (if so equipped) Auto-reverse function The auto-reverse function can be activated when a window is closed by automatic operation. Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window occurs. WARNING Automatic operation There are some small distances immediately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc.
automatically open or close all the way. To stop the roof, push the switch once more while it is opening or closing. If the moonroof does not operate properly after performing the procedure above, have your vehicle checked by a NISSAN dealer. Tilting the moonroof Auto-reverse function (when closing or tilting down the moonroof) To tilt up, first close the moonroof, then push the 1 and release it; it switch to the tilt up position 䊊 need not be held. To tilt down the moonroof, push 2 .
To close the sunshade: Sunshade ● To fully close the sunshade, push the switch 2 toward the close position. 䊊 Open and close the sunshade by sliding it forward or backward. If the moonroof does not close WARNING ● To avoid personal injury, keep your hands, fingers and head away from the sunshade arm, the arm rail and sunshade inlet port. Have your NISSAN dealer check and repair the moonroof. ● Do not allow children near the rear sunshade system. They could be injured.
● Do not push the sunshade arm with your hands, etc., as this may deform it. Improper operation or damage to the sunshade may result. ● Do not put any object into the sunshade inlet port as this may result in improper operation or damage the sunshade. ● Do not hang any object on the arm rail as this may result in improper operation or damage the sunshade. ● Do not forcefully pull the sunshade. Doing so may elongate the sunshade. Improper operation or damage to the sunshade may result.
INTERIOR LIGHT NOTE: The footwell lights and step lights illuminate when the driver and passenger doors are open regardless of the interior light switch position. These lights will turn off automatically after a period of time while doors are open to prevent the battery from becoming discharged. CAUTION Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.
PERSONAL LIGHTS MAP LIGHTS CARGO LIGHT LIC1413 LIC2304 SIC2063A To turn on the personal lights, press and release 1 . the switch 䊊 Push the button to turn the map lights on. To turn them off, press the button again. The cargo light on the overhead trim has a threeposition switch. To operate, push the switch to the desired position. To turn the personal lights off, press and release 1 . the switch 䊊 CAUTION Do not use for extended periods of time with the engine stopped.
HOMELINK® UNIVERSAL TRANSCEIVER (if so equipped) CAUTION Do not use for extended periods of time with the engine stopped. This could result in a discharged battery. The HomeLink® Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink® Universal Transceiver: ● Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems.
PROGRAMMING HOMELINK® If you have any questions or are having difficulty programming your HomeLink® buttons, refer to the HomeLink® web site at: www.homelink.com or call 1-800-355-3515. NOTE: Place the ignition switch in the ACC position when programming HomeLink®. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink® for quicker programming and accurate transmission of the radio-frequency. 1.
4. At the receiver located on the garage door opener motor in the garage, locate the “learn” or “smart” button (the name and color of the button may vary by manufacturer but it is usually located near where the hanging antenna wire is attached to the unit). If there is difficulty locating the button, reference the garage door opener’s manual. 5. Press and release the “learn” or “smart” button. 6. Return to the vehicle and firmly press and hold the trained HomeLink® button for two seconds and release.
PROGRAMMING TROUBLEDIAGNOSIS CLEARING THE PROGRAMMED INFORMATION If the HomeLink® does not quickly learn the hand-held transmitter information: The following procedure clears the programmed information from both buttons. Individual buttons cannot be cleared. However, individual buttons can be reprogrammed, see “Reprogramming a single HomeLink® button” in this section. ● replace the hand-held transmitter batteries with new batteries.
FCC Notice: For USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
MEMO Instruments and controls 2-63
3 Pre-driving checks and adjustments Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 NISSAN Intelligent Key® . . . . . . . . . . . . . . . . . . . . . . . . 3-2 NISSAN Vehicle Immobilizer System keys . . . . . . . . . 3-4 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Locking with inside lock knob . . . . . . . . . . . . .
Entry/exit function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37 Setting memory function. . . . . . . . . . . . . . . . . . . . . . . . 3-38 System operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
KEYS LPD0350 Type A 1. 2. 3. Intelligent Key (2 sets) Mechanical key Key number plate (1 plate) 3-2 Pre-driving checks and adjustments WPD0427 Type B LPD2052 Type C NISSAN INTELLIGENT KEY® Your vehicle can only be driven with the Intelligent Keys which are registered to your vehicle’s Intelligent Key system components and NISSAN Vehicle Immobilizer System components. As many as 4 Intelligent Keys can be registered and used with one vehicle.
A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record key numbers so it is very important to keep track of your key number plate. A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, your NISSAN dealer can duplicate it.
CAUTION Always carry the mechanical key installed in the Intelligent Key slot. See “Doors” in this section and “Storage” in the “Instruments and controls” section of this manual. Valet hand-off When you have to leave a key with a valet, give them the Intelligent Key itself and keep the mechanical key with you to protect your belongings. To prevent the glove box from being opened during valet hand-off, follow the procedure below. 1. Remove the mechanical key from the Intelligent Key. 2.
DOORS When the doors are locked using one of the following methods, the doors can not be opened using the inside or outside door handles. The doors must be unlocked to open the doors. Opening and closing windows The driver’s door key operation allows you to open and close windows equipped with automatic operation at the same time. ● To open the windows, turn the driver’s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked.
Lockout protection When the power door lock switch is moved to the lock position and any door is open, all doors will lock and unlock automatically. With the Intelligent Key left in the vehicle and any door is open, all doors will unlock automatically and a chime will sound after the door is closed. These functions help to prevent the Intelligent Key from being accidentally locked inside the vehicle.
NISSAN INTELLIGENT KEY® 4. When activated, the hazard indicator will flash twice. When deactivated, the hazard indicator will flash once. WARNING ● Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufacturer for the possible influences before use. 5. The ignition switch must be placed in the OFF and ON position again between each setting change.
CAUTION ● Be sure to carry the Intelligent Key with you when operating the vehicle. ● Never leave the Intelligent Key in the vehicle when you leave the vehicle. The Intelligent Key is always communicating with the vehicle as it receives radio waves. The Intelligent Key system transmits weak radio waves.
When the Intelligent Key battery is discharged or strong radio waves are present near the operating location, the Intelligent Key operating range becomes narrower, and the Intelligent Key may not function properly. If an Intelligent Key is lost or stolen, NISSAN recommends erasing the ID code of that Intelligent Key from the vehicle. This may prevent the unauthorized use of the Intelligent Key to operate the vehicle. For information regarding the erasing procedure, contact a NISSAN dealer.
● To prevent the Intelligent Key from being left inside the vehicle, make sure you carry the Intelligent Key with you and then lock the doors. ● Do not pull the door handle before pushing the door handle request switch. The door will be unlocked but will not open. Release the door handle once and pull it again to open the door. WPD0375 DOOR LOCKS/UNLOCKS PRECAUTION ● Do not push the door handle request switch with the Intelligent Key held in your hand as illustrated.
● Doors do not lock by pushing the door handle request switch while any door is open. However, doors lock with the mechanical key even if any door is open. ● Doors do not lock with the door handle request switch with the Intelligent Key inside the vehicle and a beep sounds to warn you. However, when an Intelligent Key is inside the vehicle, doors can be locked with another Intelligent Key. CAUTION LPD2105 Locking doors 1.
Lockout protection CAUTION To prevent the Intelligent Key from being accidentally locked in the vehicle, lockout protection is equipped with the Intelligent Key system. The lockout protection may not function under the following conditions: When the driver’s side door is open, the doors are locked, and then the Intelligent Key is put inside the vehicle and all the doors are closed; the lock will automatically unlock and the door buzzer sounds.
ing the door handle, push the door handle request switch to unlock the door. HOW TO USE THE REMOTE KEYLESS ENTRY FUNCTION All doors will be locked automatically unless one of the following operations is performed within 1 minute after pushing the request switch. The remote keyless entry function can operate all door locks using the remote keyless function of the Intelligent Key. The remote keyless function can operate at a distance of 33 ft (10 m) away from the vehicle.
CAUTION After locking the doors using the Intelligent Key, be sure that the doors have been securely locked by operating the door handles. WPD0359 Locking doors WPD0360 Unlocking doors 1. Place the ignition switch in the LOCK position. 1. Press the Key. 2. Close all doors. 2. The hazard warning lights flash once. 3. Press the Key. button on the Intelligent 4. The hazard warning lights flash twice and the horn beeps once. 5. All doors will be locked.
NOTE: The unlocking operation can be changed in Selective door unlock in the Vehicle Settings of the vehicle information display. For additional information, see “Vehicle information display” in the “Instruments and controls” section of this manual. All doors will be locked automatically unless one of the following operations is performed within button: 1 minute after pressing the ● Opening any doors. ● Pushing the ignition switch.
Linking the keyfob to automatic drive positioner memory If the vehicle is equipped with automatic drive positioner, the keyfob can be linked to a memory setting. See “Automatic drive positioner” in this section. WPD0415 WPD0362 Using the panic alarm Answer back horn feature If you are near your vehicle and feel threatened, you may activate the panic alarm to call attention button on the by pressing and holding the Intelligent Key for longer than 0.5 seconds.
NOTE: WARNING SIGNALS If you change the answer back horn and light flash feature with the Intelligent Key, the vehicle information display screen will show the current mode after the ignition switch has been cycled from the OFF to the ON position. The vehicle information display screen can also be used to change the answer back horn mode. See “Answer back horn” in the “Instruments and controls” section.
TROUBLESHOOTING GUIDE Verify the location of all Intelligent Keys that are programmed for the vehicle. If another Intelligent Key is in range or inside the vehicle, the vehicle system may respond differently than expected. Symptom The Shift to Park warning appears on the When stopping the engine display and the inside warning chime sounds continuously. When shifting the shift lever to the P (Park) The Push ignition to OFF warning appears position in the display.
Symptom Possible Cause The Intelligent Key battery indicator appears The battery charge is low. on the display. When pushing the ignition switch to start the engine When pushing the ignition switch The No Key Detected warning appears on the display, the outside chime sounds 3 times and the inside warning chime sounds for approximately 3 seconds. The Intelligent Key system warning light in the meter illuminates in yellow. Remedy Replace the battery with a new one.
REMOTE ENGINE START (if so equipped) Laws in some local communities may restrict the use of remote starters. For example, some laws require a person using remote start to have the vehicle in view. Check local regulations for any requirements. Other conditions may affect the function of the Remote Engine Start feature. See “Conditions the remote start will not work” in this section for additional information. Other conditions can affect the performance of the Intelligent Key transmitter.
EXTENDING ENGINE RUN TIME CANCELING A REMOTE START The remote start feature can be extended one time by performing the steps listed in “Remote starting the vehicle” in this section. Run time will be calculated as follows: To cancel a remote start, perform one of the following: ● The first 10 minute run time will start when the remote start function is performed. ● The second 10 minutes will start immediately when the remote start function is performed.
HOOD LIFTGATE WARNING ● Always be sure the liftgate has been closed securely to prevent it from opening while driving. ● Do not drive with the liftgate open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Exhaust gas” in the “Starting and driving” section of this manual. LPD2107 1 䊊 2 䊊 Pull the hood lock release handle located below the driver side instrument panel. The hood will spring up slightly.
LPD2063 LPD2108 OPERATING THE MANUAL LIFTGATE (if so equipped) Liftgate switch LPD0249 Instrument panel switch The power door lock system allows you to lock or unlock all doors including the liftgate simultaneously. To open the liftgate, pull up on the handle. To close, lower and push the liftgate down securely.
NOTE: To open, close or reverse the power liftgate, the shift lever must be in P (Park). Also, the power liftgate will not operate if battery voltage is low. LPD2109 Liftgate opener switch OPERATING THE POWER LIFTGATE (if so equipped) WARNING ● Make sure that all passengers have their hands, etc., inside the vehicle before closing the liftgate. ● Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls.
Auto Reverse: If an obstacle is detected during power open or power close, a warning chime will sound and the liftgate will reverse direction and return to the full open or full close position. If a second obstacle is detected, the liftgate motion will stop and the liftgate will enter manual mode. To open the liftgate manually, press the liftgate A and lift the liftgate. opener switch 䊊 To close, lower and push the liftgate down securely. A pinch strip is mounted on each side of the liftgate.
LIFTGATE RELEASE WARNING ● Always be sure the liftgate has been closed securely to prevent it from opening while driving. ● Do not drive with the liftgate open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Exhaust gas” in the “Starting and driving” section of this manual. CAUTION SPA2547 POWER LIFTGATE MAIN SWITCH The power liftgate operation can be turned on or off by the power liftgate main switch on the instrument panel.
FUEL-FILLER DOOR LIFTGATE POSITION SETTING The liftgate can be set to open to a specific height by performing the following: 1. Open the liftgate using the request switch or the Intelligent Key. 2. Pull the liftgate down to the desired position and hold the liftgate (the liftgate will have some resistance when being manually adjusted).
To lock, close the fuel-filler door securely and lock the doors. FUEL-FILLER CAP WARNING ● Gasoline is extremely flammable and highly explosive under certain conditions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling. ● Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically.
TILT/TELESCOPIC STEERING WARNING ● Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident. LPD2082 To remove the fuel-filler cap: 1. Turn the fuel-filler cap counterclockwise to remove. 1 2. Put the fuel-filler cap on the cap holder 䊊 while refueling. To install the fuel-filler cap: 1. Insert the fuel-filler cap straight into the fuelfiller tube. 2. Turn the fuel-filler cap clockwise until a single click is heard.
CAUTION For vehicles with automatic drive positioner: Failure to reset the tilt and telescoping functions of the steering wheel, after the vehicle’s battery has been discharged, may prevent the steering wheel position from being adjusted.
SUN VISORS 1 䊊 Entry/Exit function The automatic drive positioner system will make the steering wheel move up automatically when the driver’s door is opened and the ignition switch is in the LOCK position. This lets the driver get into and out of the seat more easily. The steering wheel moves back into position when the driver’s door is closed and the ignition switch is pushed. 2 䊊 3 䊊 To block glare from the front, swing down the sun visor.
MIRRORS AUTOMATIC ANTI-GLARE REARVIEW MIRROR (if so equipped) The inside mirror is designed so that it automatically dims during night time conditions and according to the intensity of the headlights of the vehicle following you. The automatic anti-glare feature is activated when the ignition switch is in the ON position. The indicator light will illuminate when the automatic anti-glare feature is operating.
For information on the compass display (if so equipped), see “Compass display” in the “Instruments and controls” section of this manual. LPD0469 Type A - Without compass Type A and Type B 2 will illuminate when the The indicator light 䊊 automatic anti-glare feature is operating. To turn off the automatic anti-glare feature, press: ● the O button for inside mirrors without compass. button for inside mirrors with ● the compass. The indicator light will turn off.
WARNING ● Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects. ● Do not adjust the mirrors while driving. You could lose control of your vehicle and cause an accident.
AUTOMATIC DRIVE POSITIONER (if so equipped) Move the shift lever to R (Reverse). The selected mirror will turn downward. The selected mirror surface will return to its original position when any of the following have occurred: ● The shift lever is moved to any position other than R (Reverse). The automatic drive positioner system has three features: ● Memory storage function ● Entry/exit function ● Seat synchronization function ● The outside mirror control switch is set to the neutral or center position.
supplemental restraint system” section, and “Tilt/Telescopic Steering” and “Outside mirrors” in this section. During this step, do not place the ignition switch in any position other than ON. 4. Push the SET switch and, within 5 seconds, push the memory switch (1 or 2). The indicator light for the pushed memory switch will come on and stay on for approximately 5 seconds after pushing the switch. After the indicator light goes off, the selected positions are stored in the selected memory (1 or 2).
not be adjusted for the driving position. Note that the function is set to disabled as the factory default setting. The seat synchronization function operates under the following conditions: ● The ignition switch is in the ON position. ● The shift lever is in the P (Park) position. If the outside mirrors or the steering wheel reaches its maximum adjustment, the function is automatically disabled. Restart the function by selecting a previously stored seat memory position using the memory switches (1 or 2).
The driver’s seat and steering wheel will return to the previous position: ● When the driver’s door is closed with the ignition switch placed in the LOCK position. ● When the ignition switch is turned from ACC to ON while the shift lever is in the P (Park) position. The entry/exit function can be adjusted or canceled through the Vehicle Settings in the vehicle information display by performing the following: ● Switch the Exit Seat Slide from ON to OFF. ● Switch the Exit Steering UP from ON to OFF.
● When the shift lever is moved from P (Park) to any other position. ● When the driver’s door remains open more than 45 seconds and the ignition switch is not in the ON position. ● The seat synchronization function is automatically disabled if the outside mirrors or steering wheel reaches its maximum adjustment. ● The seat synchronization function will not operate if the seat is adjusted over one of the following maximum thresholds: – Seat sliding: 3.0 in (76 mm) – Seatback reclining: 9.
MEMO 3-40 Pre-driving checks and adjustments
4 Monitor, climate, audio, phone and voice recognition systems Control panel buttons — color screen without Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . 4-4 How to use the NISSAN controller . . . . . . . . . . . . . . . 4-5 How to select menus on the screen . . . . . . . . . . . . . . 4-6 How to use the STATUS button . . . . . . . . . . . . . . . . . . 4-6 How to use the INFO button . . . . . . . . . . . . . . . . . . . . . 4-6 How to use the SETTING button . . . . . . . . . . . .
Manual operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-46 Operating tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-48 Servicing air conditioner. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-49 Audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-49 Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-49 FM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-129 Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . .4-130 Bluetooth® Hands-Free Phone System with Navigation System (if so equipped) . . . . . . . . . . . . . . . .4-131 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . .4-133 Voice commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-133 Connecting procedure . . . . . . . . . . . . . . . . . . . . . . . .
CONTROL PANEL BUTTONS — COLOR SCREEN WITHOUT NAVIGATION SYSTEM (if so equipped) WARNING ● Positioning of the heating or air conditioning controls and display controls should not be done while driving in order that full attention may be given to the driving operation. ● Do not disassemble or modify this system. If you do, it may result in accidents, fire, or electrical shock. ● Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound.
4 during setup, If you press the BACK button 䊊 the setup will be canceled and/or the display will return to the previous screen. CAUTION ● The glass display screen may break if it is hit with a hard or sharp object. If the glass screen breaks, do not touch it. Doing so could result in an injury. ● Finish setup. 4 In some screens pressing the BACK button 䊊 accepts the changes made during setup.
2. Menu Selections: Shows the options to choose within that menu screen (for example, Pacific time zone, Mountain time zone, etc.). 3. UP/DOWN Movement Indicator: Shows that the NISSAN controller may be used to move UP/DOWN on the screen and select more options. 4. Screen Count: Shows the number of menu selections available for that screen (for example, 1/9). LHA1300 HOW TO SELECT MENUS ON THE SCREEN Vehicle functions are viewed on the center display screen in menus.
Menu Item Fuel Economy Distance to Empty Average Fuel Economy Fuel Economy Record Maintenance Items Reminder keys (1–4) Reset Distance Interval Interval Reminder Result Displays Fuel Economy menu. Displays an estimation of the distance that the vehicle can be driven before refueling. The DTE is constantly calculated based on the amount of fuel in the fuel tank and actual fuel consumption. The display is updated every 30 seconds. When the fuel level is low, the DTE display will change to (*).
HOW TO USE THE SETTING BUTTON Press the SETTING button. This screen displays and adjusts various settings and functions that are available for your vehicle. Use the NISSAN controller to select an item and then press the ENTER button. When the amber indicator next to an item is illuminated, the feature is enabled.
Menu Item Audio Display Brightness/Contrast Display off Background Color Switch Beeps Camera Clock On-screen Clock Clock Format Daylight Savings Time Time Zone Adjust Clock Result See “Audio system” in this section for more information. Adjusts the settings for the display screen. Adjusts the brightness or contrast of the map background. Toggles the display screen on and off. The amber indicator is illuminated when the display is set to “On”.
Menu Item Comfort & Convenience Auto Interior Illumination Auto Headlights Sensitivity Auto Headlights Off Delay Speed Sensing Wiper Interval Selective Door Unlock Intelligent Key Lock/Unlock Lift Steering Wheel on Exit Slide Driver Seat Back on Exit Return All Settings to Default Language/Units Result Select the “Others” key using the NISSAN controller, then select the “Comfort” key. The Comfort settings screen will be displayed.
CONTROL PANEL BUTTONS — COLOR SCREEN WITH NAVIGATION SYSTEM (if so equipped) OFF BUTTON To change the display brightness, press the OFF button. Pressing the button again will change the display to the day or the night display. The brightness can then be adjusted using the NISSAN controller. The display brightness can also be adjusted using the + (brighter) button or the ⫺ (dimmer) button. If no operation is done within 10 seconds, the display will return to the previous display.
9. 4 during setup, If you press the BACK button 䊊 the setup will be canceled and/or the display will return to the previous screen. OFF brightness control button 10. - (brightness control) button 11. VOICE button* ● Finish setup. 12. SETTING button (P. 4-17) 4 In some screens, pressing the BACK button 䊊 accepts the changes made during setup. 13. MAP button* 14. 5 functions, refer to the For the VOICE button 䊊 separate Navigation System Owner’s Manual. BACK (previous) button 15.
To help ensure safe driving, some functions cannot be operated while driving. Touch screen operation With this system, the same operations as those for the NISSAN controller are possible using the touch screen operation. The on-screen functions that are not available while driving will be “grayed out” or muted. Park the vehicle in a safe location and then operate the navigation system. WARNING ● ALWAYS give your full attention to driving. ● Avoid using vehicle features that could distract you.
2. Menu Selections: Shows the options to choose within that menu screen (for example, Bass, etc.). Touch screen maintenance If you clean the display screen, use a dry, soft cloth. If additional cleaning is necessary, use a small amount of neutral detergent with a soft cloth. Never spray the screen with water or detergent. Dampen the cloth first, and then wipe the screen. 3. Up/Down Movement Indicator: Shows that the NISSAN controller may be used to move up or down on the screen and select more options. 4.
HOW TO USE THE STATUS BUTTON HOW TO USE THE INFO BUTTON Press the INFO button. This screen sets or displays various information that is helpful for using the vehicle. Available items include fuel economy, maintenance, navigation and voice recognition information. The STATUS button is used to display system information. Three different split screens of information are available.
Menu Item Fuel Economy Distance to Empty Average Fuel Economy Fuel Economy History Maintenance Items Reminder keys Reset Distance Interval Interval Reminder Where am I? Traffic Info Weather Info Map Update Navigation Version Voice Recognition Result Displays Fuel Economy menu. Displays an estimation of the distance that the vehicle can be driven before refueling. The DTE is constantly calculated based on the amount of fuel in the fuel tank and actual fuel consumption.
HOW TO USE THE SETTING BUTTON Press the SETTING button. This screen displays and adjusts various settings and functions that are available for your vehicle. When the amber indicator next to an item is illuminated, the feature is enabled. LHA1236 Menu Item Navigation Audio Phone Bluetooth Volume & Beeps Navigation volume Phone Volume Switch Beeps Display Brightness/Contrast Display off Result See the separate Navigation System Owner’s Manual for more information.
Menu Item Background Color Color Theme Clock On-screen Clock Clock Format Offset (hour), Offset (min) Daylight Savings Time Time Zone Language & Units Select Language Select Units Voice Recognition Camera Settings Image Viewer Result Adjusts the display screen between day and night mode. Changes the color of the background, arrows and bars on the screen. Adjusts the clock settings. Toggles on or off the clock in the upper right corner of the display. Toggles between a 12-hour and 24-hour clock.
Menu Item Others Comfort Auto Interior Illumination Light Sensitivity Light Off Delay Speed Sensing Wiper Interval Selective Door Unlock Intelligent Key Lock/ Unlock Lift Steering Wheel on Exit Slide Driver Seat Back on Exit Return All Settings to Default Result Select the “Others” key using the NISSAN controller. Voice Recognition, language and units setting screen will be displayed. Select the “Others” key using the NISSAN controller, then select the “Comfort” key.
IMAGE VIEWER (if so equipped) OFF BUTTON USING THE IMAGE VIEWER To change the display brightness, press the OFF button. Pressing the button again will change the display to the day or the night display. The brightness can then be adjusted using the NISSAN controller. When a compatible portable storage device is plugged into the USB jack located in the center console, compatible image files stored on the device can be viewed on the control panel device.
Select the “Full Screen Display” key and press the ENTER button to view a full screen version of the image. Viewing images in a slideshow To view all of the images on the device in a slideshow, first enter the full screen mode while viewing one of the images. The slideshow control buttons are located on the right side of the screen. Image requirements: ● Image type: JPEG ● File extensions: *.jpg, *.
Slideshow settings While in slideshow mode, the following settings can be accessed: Settings Slideshow Speed Slideshow Order Random Order List Changes the frequency at which images are changed during a slideshow. Choose one of the options on the screen or “No Auto Change” to have the images not change automatically. Changes images in a random order when selected. Changes images in the order in which they are saved on the USB device.
REARVIEW MONITOR (if so equipped) When the shift lever is shifted into the R (Reverse) position, the monitor display shows a rearward view from the vehicle. ● Do not put anything on the rear view camera. The rear view camera is installed above the license plate. The system is designed as an aid to the driver in situations such as slot parking or parallel parking. ● When washing the vehicle with highpressure water, be sure not to spray it around the camera.
5 : Vehicle width guide lines 䊊 6 : Predictive course lines 䊊 ● On a snow-covered or slippery road, there may be a difference between the predictive course line and the actual course line. Indicate the predictive course when backing up. The predictive course lines will be displayed on the monitor when the shift lever is in the R (Reverse) position and the steering wheel is turned.
4. Maneuver the steering wheel to make the D parallel to the vehicle width guide lines 䊊 C . When the back of the parking space 䊊 C , maneuvehicle enters the parking space 䊊 ver the steering wheel to make the vehicle D parallel to the parking width guide lines 䊊 C. space 䊊 5. When the vehicle is parked in the space completely, move the shift lever to the P (Park) position and apply the parking brake.
B . Note that any object on the hill is the place 䊊 the hill is further than it appears on the monitor. B . Note that any object on the hill is the place 䊊 the hill is closer than it appears on the monitor. LHA1200 Backing up on a steep downhill When backing up the vehicle down a hill, the distance guide lines and the vehicle width guide lines are shown farther than the actual distance. For example, the display shows 3 ft (1.0 m) to the A , but the actual 3 ft (1.
A if the object projects over the the position 䊊 actual backing up course. PREDICTIVE COURSE LINE SETTINGS To turn on or off the predictive course line display, press the SETTING button, select the “Camera” key and press the ENTER button. Predictive Course Lines: When this item is turned on, the predictive course lines will be displayed on the monitor when the shift lever is the R (Reverse) position.
AROUND VIEW® MONITOR (if so equipped) OPERATING TIPS ● When the shift lever is shifted to the R (Reverse) position, the display screen automatically changes to the RearView Monitor mode. However, the radio can be heard. ● When the view is switched, the display images on the screen may be displayed with some delay. ● When the temperature is extremely high or low, the screen may not clearly display objects. This is not a malfunction.
● The distance between objects viewed on the Around View Monitor differs from the actual distance. The system is designed as an aid to the driver in situations such as slot parking or parallel parking. ● The cameras are installed on the front grille, the outside mirrors and above the rear license plate. Do not put anything on the cameras. ● When washing the vehicle with highpressure water, be sure not to spray it around the cameras.
CAUTION Do not scratch the camera lens when cleaning dirt or snow from the front of the camera. AVAILABLE VIEWS WARNING ● The distance guide line and the vehicle width line should be used as a reference only when the vehicle is on a paved, level surface. The distance viewed on the monitor may be different than the actual distance between the vehicle and displayed objects. ● Objects in the rearview will appear visually opposite than when viewed in the rearview and outside mirrors.
NOTE: When the monitor displays the front view and the steering wheel turns about 90 degrees or less from the neutral position, both the right and left predictive course 6 are displayed. When the steering lines 䊊 wheel turns about 90 degrees or more, a line is displayed only on the opposite side of the turn. SAA1896 Rearview 5 : Vehicle width guide lines 䊊 Indicate the vehicle width when backing up. 6 : Predictive course lines 䊊 Indicate the predictive course when operating the vehicle.
After the ignition switch is placed in the ON 2 is highlighted position, the non-viewable area 䊊 in yellow for three seconds after the bird’s-eye view is displayed. In addition, the non-viewable corners are displayed in red and blink for the first 3 to remind the driver to be three seconds 䊊 cautious. ● A line on the ground may be misaligned and is not seen as being straight at the seam of the views. The misalignment will increase as the line proceeds away from the vehicle.
Backing up on a steep uphill CAUTION ● The turn signal light may look like the side-of-vehicle line. This is not a malfunction. When backing up the vehicle up a hill, the distance guide lines and the vehicle width guide lines are shown closer than the actual distance. For example, the display shows 3 ft (1.0 m) to the A , but the actual 3 ft (1.0 m) distance on place 䊊 B . Note that any object on the hill is the place 䊊 the hill is further than it appears on the monitor.
Backing up on a steep downhill When backing up the vehicle down a hill, the distance guide lines and the vehicle width guide lines are shown farther than the actual distance. For example, the display shows 3 ft (1.0 m) to the A , but the actual 3 ft (1.0 m) distance on place 䊊 B . Note that any object on the hill is the place 䊊 the hill is closer than it appears on the monitor. LHA1200 LHA1201 Backing up near a projecting object A do not touch the The predicted course lines 䊊 object in the display.
A if the object projects over the the position 䊊 actual backing up course. HOW TO SWITCH THE DISPLAY With the ignition switch in the ON position, press the CAMERA button or move the shift lever to the R (Reverse) position to operate the Around View Monitor. The Around View Monitor displays different split screens views depending on the position of the shift lever. Press the CAMERA button to switch between the available views.
The display will switch from the Around View Monitor screen when: WARNING ● The sonar (parking sensor) is a convenience feature. It is not a substitute for proper parking. ● When the shift lever is in the D (Drive) position and the vehicle speed increases above approximately 6 mph (10 km/h) ● The driver is always responsible for safety during parking and other maneuvers. ● When the sonar no longer detects an object the screen will automatically switch back the previously displayed screen.
● The system will not detect small objects below the bumper, and may not detect objects close to the bumper or on the ground. ● The system may not detect the following objects: – Fluffy objects such as snow, cloth, cotton, glass or wool. – Thin objects such as rope, wire or chain. – Wedge-shaped objects. ● If your vehicle sustains damage to the bumper fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of objects or false alarms.
OPERATING TIPS CAUTION ● Do not use alcohol, benzine or thinner to clean the camera. This will cause discoloration. To clean the camera, wipe with a cloth dampened with a diluted mild cleaning agent and then wipe with a dry cloth. ● Do not damage the camera as the monitor screen may be adversely affected. LHA2550 VIEW MALFUNCTION When the “!” icon is displayed on the screen, the Around View Monitor may not be calibrated correctly.
VENTS LHA2480 1 , Adjust air flow direction for the center vents 䊊 2 , and rear driver’s and passenger’s side vents 䊊 3 by moving the vent slide and/or vent vents 䊊 assemblies. Open or close the vents using the dial. Move the to open the vents or toward dial toward the the to close them.
HEATER AND AIR CONDITIONER (automatic) (Type A) ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals. LHA2472 Type A 1. 2. 3. 4. 5. 6. 7. 8.
AUTOMATIC OPERATION Cooling and/or dehumidified heating (AUTO) This mode may be used all year round as the system automatically works to keep a constant temperature. Air flow distribution and fan speed are also controlled automatically. 1. Press the AUTO button on. (The indicator on the button will illuminate and AUTO will be displayed.) 2. Operate the driver’s side temperature control buttons. ● Adjust the temperature display to about 75°F (24°C) for normal operation.
Automatic intake air control In the AUTO mode, the intake air will be controlled automatically. To manually control the inair recirculation button. take air, press the To return to the automatic control mode, press air recirculation button for and hold the about 2 seconds. The indicator light will flash twice, and then the intake air will be controlled automatically. Air flow control Pressing the MODE button manually controls air flow and selects the air outlet: — Air flows from center and side vents.
OPERATING TIPS ● When the engine coolant temperature and outside air temperature are low, the air flow from the foot outlets may not operate for a maximum of 150 seconds. However, this is not a malfunction. After the coolant temperature warms up, air flow from the foot outlets will operate normally. LHA2473 The sunload sensor, located on the top driver’s side of the instrument panel, helps the system maintain a constant temperature. Do not put anything on or around this sensor.
HEATER AND AIR CONDITIONER (automatic) (Type B) 7. 8. 9. (fan speed control) dial/ON/OFF button (front defroster) button Temperature control dial (driver’s side)/ AUTO (automatic) climate control ON button WARNING ● The air conditioner cooling function operates only when the engine is running. ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone.
● Odors from inside and outside the vehicle can build up in the air conditioner unit. Odor can enter the passenger compartment through the vents. ● The temperature of the passenger compartment will be maintained automatically. Air flow distribution and fan speed are also controlled automatically. ● When parking, set the heater and air conditioner controls to turn off air recirculation to allow fresh air into the passenger compartment. This should help reduce odors inside the vehicle.
MANUAL OPERATION Fan speed control Turn the fan speed control dial to manually control the fan speed. Press the AUTO button to return to automatic control of the fan speed. Air recirculation Press the air recirculation button to recirculate interior air inside the vehicle. The indicator light on the button will come on. Air flow control Pressing the MODE button manually controls air flow and selects the air outlet: — Air flows from center and side vents.
Automatic operation: 1. Press the AUTO button. The AUTO indicator light will illuminate and “AUTO” will appear on the display. 2. Turn the temperature control dial (driver’s side) to set the desired temperature. Manual operation : ● Temperature control Press the temperature control buttons to set the desired temperature. ● Fan speed control Press the fan speed increase or decrease button to manually control the fan speed. 3. If the A/C indicator light illuminates, press the A/C button.
To turn system off Press the OFF button. OPERATING TIPS ● When the engine coolant temperature and outside air temperature are low, the air flow from the foot outlets may not operate for a maximum of 150 seconds. However, this is not a malfunction. After the coolant temperature warms up, air flow from the foot outlets will operate normally. LHA2134 1. 2. 3. 4. 5. 6. 7.
SERVICING AIR CONDITIONER AUDIO SYSTEM The air conditioner system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. RADIO This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system.
Reception conditions will constantly change because of vehicle movement. Buildings, terrain, signal distance and interference from other vehicles can work against ideal reception. Described below are some of the factors that can affect your radio reception. Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter), static or flutter can be heard.
Compact disc (CD) player (models without Navigation System) CAUTION ● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player. LHA0099 AUDIO OPERATION PRECAUTIONS ● The CD player sometimes cannot function when the compartment temperature is extremely high or low. Decrease/increase the temperature before use. ● Do not expose the CD to direct sunlight. ● Trying to load a CD with the CD door closed could damage the CD and/or CD changer.
● This audio system can only play prerecorded CDs. It has no capability to record or burn CDs. ● If the CD cannot be played, one of the following messages will be displayed. CHECK DISC: ● Confirm that the CD is inserted correctly (the label side is facing up, etc.). ● Confirm that the CD is not bent or warped and it is free of scratches. PRESS EJECT: This is an error due to excessive temperature inside the player. Remove the CD by pressing the EJECT button. After a short time, reinsert the CD.
Disc Read Error: Region Invalid ● Confirm that the CD/DVD is inserted correctly (the label side is facing up, etc.). ● The DVD is not for region 1 or all regions. ● Confirm that the CD/DVD is not bent or warped and it is free of scratches. Please Eject Disc: This error may be due to the temperature inside the player getting too high. Remove the CD/DVD by pushing the EJECT button, and after a short time reinsert the CD/DVD. The CD/DVD can be played when the temperature of the player returns to normal.
● This copyright protected technology cannot be used without a permit from Macrovision Corporation. It is limited to personal use, etc., as long as the permit from Macrovision Corporation is not issued. ● Modifying or disassembling is prohibited. ● Dolby digital is manufactured under license from Dolby Laboratories, Inc. ” ● Dolby and the double D mark “ are trademarks of Dolby Laboratories, Inc. ” ● DTS and DTS Digital Surround “ are registered trademarks of Digital Theater Systems, Inc.
● An incorrect song title may appear when the Play Mode is changed while using an iPod® nano (2nd Generation). ● Audiobooks may not play in the same order as they appear on an iPod®. ● Large video files cause slow responses in an iPod®. The vehicle center display may momentarily black out, but will soon recover. ● If an iPod® automatically selects large video files while in the shuffle mode, the vehicle center display may momentarily black out, but will soon recover.
● Sampling frequency — Sampling frequency is the rate at which the samples of a signal are converted from analog to digital (A/D conversion) per second. Playback order: Music playback order of a CD with MP3 or WMA files is as illustrated. ● The names of folders not containing MP3 or WMA files are not shown in the display. ● Multisession — Multisession is one of the methods for writing data to media.
Specification chart: Supported media Supported file systems MP3 Supported versions WMA*1 Version Sampling frequency Bit rate Version Sampling frequency Bit rate Tag information (Song title and artist name) Folder levels Text character number limitation Displayable character codes*3 CD, CD-R, CD-RW, USB 2.0 CD, CD-R, CD-RW, ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported.
Troubleshooting guide: Symptom Cannot play Poor sound quality It takes a relatively long time before the music starts playing. Music cuts off or skips Skipping with high bit rate files Moves immediately to the next song when playing Songs do not play back in the desired order Cause and Countermeasure Check if the CD/USB device was inserted correctly. Check if the CD is scratched or dirty. Check if there is condensation inside the player.
CD, DVD or USB with Compressed Audio Files (models with Navigation System) The file types supported by this system are MP3, WMA, AAC/M4A and ATRAC3. Explanation of terms: ● MP3 — MP3 is short for Moving Pictures Experts Group Audio Layer 3. MP3 is the most well known compressed digital audio file format. This format allows for near “CD quality” sound, but at a fraction of the size of normal audio files. MP3 conversion of an audio track can reduce the file size by approximately 10:1 ratio (Sampling: 44.
Playback order: Music playback order of a CD, DVD or USB device with compressed audio files is as illustrated. ● The folder names of folders not containing compressed audio files are not shown in the display. ● If there is a file in the top level of the disc/USB, “Root Folder” is displayed. ● The playback order is the order in which the files were written by the writing software, so the files might not play in the desired order.
Specification chart: Supported media Supported file systems MP3 Supported versions*1 WMA*2 AAC ATRAC Version Sampling frequency Bit rate Version Sampling frequency Bit rate Sampling frequency Bit rate Version Tag information (Song title and artist name) Folder levels Text character number limitation Displayable character codes*3 CD, CD-R, CD-RW, DVD-ROM, DVD±R, DVD±RW, DVD±R DL, USB 2.
Troubleshooting guide: Symptom Cannot play Poor sound quality It takes a relatively long time before the music starts playing. Music cuts off or skips Skipping with high bit rate files Moves immediately to the next song when playing Songs do not play back in the desired order Cause and Countermeasure Check if the CD/DVD/USB device was inserted correctly. Check if the CD/DVD is scratched or dirty. Check if there is condensation inside the player.
Compressed Video Files (models with Navigation System) Explanation of terms: ● DivX – DivX refers to the DivX® codec owned by Div, Inc. used for a lossy compression of video based on MPEG-4. ● AVI – AVI stands for Audio Video Interleave. It is standard file format originated by Microsoft Corporation. A .divx encoded file can be saved into the .avi file format for playback on this system if it meets the requirements stated in the table in this section. However, all .
Requirements for Supporting Video Playback: Media File Systems File Types Bit Rates Resolution CD, CD-R, CD-RW, DVD, DVD±R, DVD±RW, DVD±RW DL, USB 2.0 Memory CD, CD-R, CD-RW, DVD, ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet, UDF Bridge (UDF1.02+ISO9660), UDF1.5, UDF2.0 DVD±R, DVD±RW, DVD±RW * ISO9660 Level 3 (packet writing) is not supported. DL * Files saved using the Live File System component (on a Windows Vista-based computer) are not supported. * VDF1.5/VDF2.0 (packet writing) is not supported.
9. 10. 11. 12. 13. 14. SEEK/CAT button DISC button RPT/RDM button SCAN button AM·FM button DISP/CLOCK button FM/AM RADIO WITH COMPACT DISC (CD) CHANGER (if so equipped) For all operation precautions, see ⬙Audio operation precautions⬙ in this section. Audio main operation VOL/ON·OFF control: Place the ignition switch in the ACC or ON position and push the VOL/ON·OFF control knob while the system is off to call up the mode (radio or CD) that was playing immediately before the system was turned off.
Audio settings Audio Bass Treble Balance Fade Adjusts the bass to the desired level. Adjusts the treble to the desired level. Adjusts the balance to the desired level. Balance adjusts the sound level between the left and right speakers. Adjusts the fade to the desired level. Fade adjusts the sound level between the front and rear speakers. Bass, treble, balance and fade can also be adjusted by pressing the AUDIO control knob and turning it to select the item to adjust.
FM/AM radio operation SEEK/CAT and TRACK FM/AM band select: tuning buttons: Pressing the AM·FM button will change the band as follows: AM → FM1 → FM2 → AM When the AM·FM button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played. The last station played will also come on when the VOL/ON·OFF control knob is pressed ON.
To insert 6 CDs to the CD changer, press the LOAD button for more than 1.5 seconds. The slot numbers (1 – 6) will illuminate on the display when CDs are loaded into the changer. DISC button: When the DISC button is pressed with the system off and a compact disc loaded, the system will turn on and the compact disc will start to play. When the DISC button is pressed with a compact disc loaded with the radio playing, the radio will automatically be turned off and the compact disc will start to play.
SCAN button: CD IN indicator: While listening to a CD, press the SCAN button to preview the first 10 seconds of each track on the CD playing. Pressing the SCAN button again during this 10 second period stops the scan and the CD remains on that track. The slot numbers (1 – 6) will illuminate if CDs have been loaded into the changer in CD mode only. CD EJECT: Current/Selected disc: ● Press the button, then press the slot number (1 – 6) for the desired disc. The compact disc will be ejected.
*No satellite radio reception is available when the AUX button is pressed to access satellite radio stations unless optional satellite receiver and antenna are installed and a SiriusXM Satellite Radio service subscription is active. Satellite radio is not available in Alaska, Hawaii and Guam. FM/AM/SAT RADIO WITH COMPACT DISC (CD) PLAYER (if so equipped) For all operation precautions, see ⬙Audio operation precautions⬙ in this section.
Audio settings Audio Bass Treble Balance Fade Speed Sensitive Vol. Adjusts the bass to the desired level. Adjusts the treble to the desired level. Adjusts the balance to the desired level. Balance adjusts the sound level between the left and right speakers. Adjusts the fade to the desired level. Fade adjusts the sound level between the front and rear speakers. Adjusts the speed sensitive volume function, which increases the volume of the audio system as the speed of the vehicle increases.
Press the BACK button to exit the CD text display screen. FM/AM/SAT radio operation FM/AM band select: Pressing the FM·AM button will change the band as follows: AM → FM1 → FM2 → AM When the FM·AM button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played. WHA0949 CD/MP3 display mode While listening to a CD or an MP3/WMA CD, certain text might be able to be displayed (when CD encoded with text is being used).
XM band select: Pressing the AUX button will change the band as follows: USB → XM1* → XM2* → XM3* → AUX → USB (satellite, if so equipped) When the AUX button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played. The last station played will also come on when the VOL/ON·OFF control knob is pressed ON.
When the “Text” key is selected with the NISSAN controller on the display while the radio is playing, additional information is displayed on the screen. If the station broadcasts RDS information, the RDS icon is displayed. Compact disc (CD) player operation Place the ignition in the ACC or ON position and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start playing.
CD EJECT button: The auxiliary input jacks are color coded for identification purposes: button is pressed with the comWhen the pact disc loaded, the compact disc will be ejected. ● Red – right channel audio input ● White – left channel audio input ● Yellow – video input button is pressed while the When the compact disc is being played, the compact disc will eject and the system will turn off. Before connecting a device to the auxiliary input jacks, turn off the power of the portable device.
Additional features For more information about the iPod® player available with this system, see “iPod® player operation without Navigation System” in this section. For more information about the USB interface available with this system, see “USB interface (models without Navigation System)” in this section. LHA1367 AUX settings Select the “Settings” key using the NISSAN controller and press the ENTER button.
*No satellite radio reception is available when the SAT button is pressed to access satellite radio stations unless optional satellite receiver and antenna are installed and a SiriusXM Satellite Radio service subscription is active. Satellite radio is not available in Alaska, Hawaii and Guam. FM/AM/SAT RADIO WITH CD/DVD PLAYER (if so equipped) For all operation precautions, see ⬙Audio operation precautions⬙ in this section.
Audio settings Audio Bass Treble Balance Fade Speed Adjust Vol. DivX Registration Code Display Album Cover Art Adjusts the bass to the desired level. Adjusts the treble to the desired level. Adjusts the balance to the desired level. Balance adjusts the sound level between the left and right speakers. Adjusts the fade to the desired level. Fader adjusts the sound level between the front and rear speakers.
● Song displays the ID3 encoded tag of the song name. broadcast signal is weak, the radio will automatically change from stereo to monaural reception. ● Album displays the ID3 encoded tag of the album name. SAT band select: ● Artist displays the ID3 encoded tag of the artist’s name. Some of this text might not display while playing a regular CD.
SEEK/CAT and TRACK tuning buttons: For AM or FM: button or the Press the SEEK/CAT button to tune from high to low or TRACK low to high frequencies and stop at the next broadcasting station. For XM: button or the Press the SEEK/CAT button to go to the first channel of TRACK the previous or next category. SCAN tuning: Press the SCAN button to stop at each broadcasting station for 5 seconds.
– Tags the current artist or song playing on SiriusXM Satellite Radio as a favorite. ● Music or programming type such as “Classical”, “Country”, or “Rock”. – Turn the Alert ON to indicate whenever a favorite artist or song is playing on Sirius XM Satellite Radio. The audio system must be playing Sirius XM Satellite Radio for this feature to work. ● Station specific text. – Delete a favorite artist or song. If the station broadcasts RDS information, the text information is automatically displayed.
SEEK/CAT and TRACK (Rewind and Fast Forward) buttons: (rewind) Press and hold the SEEK/CAT button or the TRACK (fast forward) button while a compact disc is playing; the compact disc will play while rewinding or fast forwarding. When the button is released, the compact disc will return to normal play speed. TUNE/FOLDER knob While playing a CD with compressed audio files, turn the TUNE/FOLDER knob right or left to play the next or previous folder.
LHA1262 Normal - Plays all tracks on the CD in sequential order until stopped. LHA1260 ● Folder List LHA1261 ● Track List The folders on the disc are displayed. Select the key of a folder name to begin playing tracks from that folder. The tracks on the disc are displayed. Select the key of a track name to begin playing that track. CD EJECT button: button is pressed with the comWhen the pact disc loaded, the compact disc will be ejected.
Before connecting a device to the auxiliary input jacks, turn off the power of the portable device. With a compatible device connected to the auxiliary input jacks, press the DISC·AUX button repeatedly until the AUX mode appears in the display. The output from the device will be played through the display (when the vehicle is in the (P) Park position and the parking brake engaged) and audio system.
DIGITAL VERSATILE DISC (DVD) PLAYER OPERATION (models with Navigation System) Precautions Start the engine when using the DVD entertainment system. LHA1394 Additional features For more information about the iPod® player available with this system, see “iPod® player operation with Navigation System” in this section. For more information about the USB interface available with this system, see “USB interface (models with Navigation System)” in this section.
The operation screen will be turned on when the DISC-AUX button is pressed while a DVD is playing. The operation screen will turn off automatically after a period of time. To turn it on again, press the DISC-AUX button. DVD operation keys LHA1376 Playing a DVD When the DVD is playing without the operation screen being shown, you may use the touchscreen to select items from the displayed video. You may also use the NISSAN controller to select an item from the displayed video.
– Select the directional keys to move the cursor on the DVD menu. – Select the “Enter” key to fix the selected menu item. – Select the “Move” key to move the location of the operation keys on the screen. – Select the “Back” key to return to the previous menu screen. – Select the “Hide” key to hide the operation keys. ● Title Menu (DVD-VIDEO) Some menus specific to each disc will be shown. For details, see the instructions attached to the disc.
● Display Mode (DVD-VIDEO, VIDEO CD, DVD-VR) Choose from the “Full”, “Wide”, “Normal” or “Cinema” mode. CAUTION ● Do not force the USB device into the USB port. Inserting the USB device tilted or up-side-down into the port may damage the port. Make sure that the USB device is connected correctly into the USB port. ● Title List (DVD-VR) Choose the preferred title from the list. ● Play Mode Choose the preferred play mode.
Audio file operation AUX button: Place the ignition switch in the ON or ACC position and press the AUX button to switch to the USB input mode. If another audio source is playing and a USB memory device is inserted, press the AUX button repeatedly until the center display changes to the USB memory mode. If the system has been turned off while the USB memory was playing, push the ON-OFF/VOL control knob to restart the USB memory.
CAUTION ● Do not force the USB device into the USB port. Inserting the USB device tilted or up-side-down into the port may damage the port. Make sure that the USB device is connected correctly into the USB port. ● Do not grab the USB port cover (if so equipped) when pulling the USB device out of the port. This could damage the port and the cover.
● Folder List/Track List Displays the folder or track list. The “Movie Playback” key is also displayed in this list screen and enables you to switch to the movie playback mode. SEEK/CAT and TRACK buttons: while an auPress the SEEK/CAT button dio file on the USB device is playing to return to the beginning of the current track. Press the several times to skip SEEK/CAT button backward several tracks. ● Play Mode Choose the preferred play mode using the NISSAN controller or the touchscreen.
● Operation keys: To operate the USB memory, select the desired key displayed on the display screen. ● Pause: key to pause the movie file. Select the To resume playing the movie file, use key. the ● key to start playing the Select the movie file or resume the movie file if it has been paused. LHA1379 Movie file operation Park the vehicle in a safe location for the front seat occupants to operate the USB memory while watching the images. ● Stop: Select the movie file.
● 10 Key Search Select the “10 Key Search” key to open the number entry screen. Input the number you want to search for and the specified file or folder will be played. ● Display Adjust the image quality of the screen. ● DRC DRC (Dynamic Range Compression) automatically adjusts the soundtrack volume level to maintain a more even sound to the speakers. LHA1380 Settings: Select the “Settings” key to adjust the following settings: ● Audio File Playback Switch to the audio playback mode.
CAUTION ● Do not force the USB device into the USB port. Inserting the USB device tilted or up-side-down into the port may damage the port. Make sure that the USB device is connected correctly into the USB port. ● Do not grab the USB port cover (if so equipped) when pulling the USB device out of the port. This could damage the port and the cover. ● Do not leave the USB cable in a place where it can be pulled unintentionally. Pulling the cable may damage the port.
● Albums ● Artists ● Genres ● Composers ● Audiobooks The following keys shown on the screen are also available: ● MENU: returns to the previous screen. ● : plays/pauses the music selected. SEEK/CAT and TRACK buttons: LHA1396 Interface: The interface for iPod® operation shown on the vehicle center display is similar to the iPod® interface. Use the NISSAN controller and the BACK button to play the iPod® with your favorite settings. The following items can be chosen from the menu list screen.
CAUTION ● Do not force the USB device into the USB port. Inserting the USB device tilted or up-side-down into the port may damage the port. Make sure that the USB device is connected correctly into the USB port. ● Do not grab the USB port cover (if so equipped) when pulling the USB device out of the port. This could damage the port and the cover. ● Do not leave the USB cable in a place where it can be pulled unintentionally. Pulling the cable may damage the port.
DISC·AUX button: When the DISC·AUX button is pressed with the system off and the iPod® connected, the system will turn on. If another audio source is playing and the iPod® is connected, press the DISC·AUX button repeatedly until the center display changes to the iPod® mode. LHA1397 LHA1398 Audio main operation Interface: Place the ignition switch in the ACC or ON position. Press the DISC·AUX button repeatedly to switch to the iPod® mode.
● Albums SEEK/CAT button or When the TRACK button is pressed for more than 1.5 seconds while the iPod® is playing, the iPod® will play while fast forwarding or rewinding. When the button is released, the iPod® will return to the normal play speed. ● Songs ● Podcasts ● Genres ● Composers The NISSAN controller can also be used to select tracks when the iPod® is playing. ● Audiobooks ● Shuffle Songs The following keys shown on the screen are also available: ● MENU: returns to the previous screen.
To exit the scrolling by letter mode, perform one of the following: ● Press the ENTER button on the NISSAN controller. ● Push the ENTER switch on the steering wheel. ● Do not touch the controls for 2 seconds. BLUETOOTH® STREAMING AUDIO (if so equipped) LHA1399 Scrolling menus: While navigating long lists of artists, albums or songs in the music menu, it is possible to scroll the list by the first letter. To activate letter indexing, perform one of the following: ● Turn the NISSAN controller quickly.
LHA1317 LHA1351 4. A screen will appear asking if you are connecting the device to use with the handsfree phone system. Select the “No” key. 5. Enter a PIN of your choice. It will be needed by your Bluetooth® audio device to complete the connection process. See the Bluetooth® audio device’s owner’s manual for more information. LHA1458 Audio main operation To switch to the Bluetooth® audio mode, press the DISC•AUX button repeatedly until the Bluetooth® audio mode is displayed on the screen.
LHA1316 Bluetooth® audio settings To adjust the Bluetooth® audio settings, follow the procedure below: LHA1296 4. Select the “Audio Player” key. LHA1297 5. A list of the connected Bluetooth® audio players is displayed. Select the name of the device you wish to edit. 1. Press the SETTING button on the control panel. 2. Select the “Bluetooth” key. 3. Select the “Connected Devices” key.
● A new disc may be rough on the inner and outer edges. Remove the rough edges by rubbing the inner and outer edges with the side of a pen or pencil as illustrated. LHA1298 6. The Device Name and Device Address are displayed on the screen. Select the “Select” key to make this device the active Bluetooth® audio player. Select the “Edit” key to edit the details of the player, such as Device Name. Select the “Delete” key to delete the device. LHA0049 CD CARE AND CLEANING ● Handle a CD by its edges.
SOURCE select switch Push the source select switch to change the mode in the following sequence: Models without Navigation System: AM → FM1 → FM2 → XM1 → XM2 → XM3 (satellite radio, if so equipped) → USB/iPod®* (if so equipped) → CD/DVD* → AUX* → AM. Models with Navigation System: AM → FM1 → FM2 → XM1 → XM2 → XM3 (satellite radio, if so equipped) → CD/DVD* → USB/iPod®* → Bluetooth® Audio* → AUX* → AM. LHA2448 1. 2. 3. 4.
CD: ● Tilt up/down for less than 1.5 seconds to increase or decrease the track number. Bluetooth® Audio (if so equipped): ● Tilt up/down for less than 1.5 seconds to increase or decrease the track number. ● Tilt up/down for more than 1.5 seconds to increase or decrease the folder number (if playing compressed audio files). AUX: ● Press the ENTER button to show the CD Menu. BACK switch DVD (if so equipped): ● Press the ENTER button to show the AUX Menu.
DUAL HEAD RESTRAINT/HEADREST DVD SYSTEM (if so equipped) If your vehicle is equipped with the Dual Head Restraint/Headrest DVD System, you can enjoy playing video files via a DVD, CD or USB memory that provides images and sound both from the front and rear display screens. You can also enjoy compatible auxiliary devices such as video games, camcorders or portable video players through the auxiliary jacks. The front and right/left rear displays can show different sources individually.
Before connecting a device to a jack, turn off the power of the portable device. To display the rear AUX screen, press the preferred side (L or R) of the AUX (L)/AUX (R) buttons (rear input jacks) on the remote controller. The connected device from the rear auxiliary input jacks cannot be displayed on the front screen. LHA2210 The angle of the rear display screen can be adjusted for optimal viewing.
It is also possible that the headphones may be too far from the transmitter which is in the rear display screen. This is not a malfunction. The sound may also be interrupted temporarily when there is an obstacle between the headphones and the transmitter. Remove the obstacle, such as opaque materials, hands, hair, etc. SAA3077 SAA3078 Headphones Volume control The headphones for this system are a wireless type and no cables are necessary. The headphones can only be used in the rear seat.
LHA2211 Type A Channel change: When the rear displays are playing different sources, slide the channel select switch to select the sound. LHA8801 Type B “Left” is the sound on the left display. “Right” is the sound on the right display. LHA2673 Remote control The remote controller has the following controls: 1. POWER button 2.
3. MENU button 4. Directional buttons 5. Backlight button 6. SETUP button 7. (next chapter) button 8. (fast forward) button 9. (stop) button 10. Volume control button 11. 12. 13. (reverse) button (play and pause) button (previous chapter) button 14. BACK button 15. SOURCE button LHA2552 Select rear displays audio source: Slide the display select switch on the remote control to the left (L) or right (R) to select each 1 .
2. Replace both batteries with new ones. ● Recommended battery: Size AA 6 2 (DVD remote controller) Size AAA 6 2 (headphones) ● Be careful not to touch the battery terminal. ● Make sure that the (+) and (-) ends on the batteries match the markings inside the compartment. 3. Close the lid securely. ● If you will not be using the remote control for long periods of time, remove the batteries.
CAUTION ● Only operate the Dual Head Restraint/Headrest DVD System while the vehicle engine is running. Operating the Dual Head Restraint/Headrest DVD System for extended periods of time with the engine OFF can discharge the vehicle battery. ● Do not allow the system to get wet. Excessive moisture such as spilled liquids may cause the system to malfunction. ● While playing VIDEO-CD media, this DVD player does not guarantee complete functionality of all VIDEO-CD formats.
Press the AUX·DVD button on the control panel and turn the display to the DVD mode, and begin playing the DVD automatically. When a DVD is loaded, it will begin playing automatically. The front screen will be turned on when the AUX·DVD button is pressed while a DVD is being played, and it will turn off automatically after a period of time. To turn it on again, press the AUX·DVD button again.
SKIP (FORWARD): Select this key and press the ENTER button to skip the chapter(s) of the disc forward. The chapters will advance the number of times the ENTER button is pressed. To skip the chapter(s) forward, it is also possible to press the corresponding button on the keypad of the remote controller. SKIP (REWIND): Select this key and press the ENTER button to skip the chapter(s) of the disc backward. The chapters will go back the number of times the ENTER button is pressed.
Arrow icons: Move the cursor to select a DVD menu. Enter: Enter the selected menu. Move: Change the display location by moving the operation key. Back: Return to the previous screen. Hide: Hide the operation key. Title Menu (front)/Menu (rear) (DVDVIDEO): Menus specific to each disc will be shown. For details, see the instructions attached to the disc. Title Search (DVD-VIDEO): A scene that belongs to a specified title will be displayed each time the “+” side or “⫺” side is selected.
Play Mode: AUX mode: Rear display settings Choose the preferred play mode using the NISSAN controller and press the ENTER button. To adjust the rear display settings, select the preferred key and press the ENTER button. The following settings are available: Use the remote controller to adjust the following items. The AUX (auxiliary input jacks) modes can be activated or deactivated individually. To activate the AUX mode, press the preferred side (L or R) of the AUX button.
Color System: To choose the color system, select from “NTSC”, “PAL”, “PAL-60”, “PAL-M”, “PAL-N” or “AUTO” using the joystick on the remote controller and tilt the joystick to the right or left. 3D Y/C filter: Set to ON/OFF using the joystick on the remote controller. When turned on, small characters and an outline of the shapes will be displayed more clearly than when turned off.
CAR PHONE OR CB RADIO CAUTION ● Do not use any solvents or cleaning solutions when cleaning the video system. ● Do not use excessive force on the monitor screen. ● Avoid touching or scratching the monitor screen as it may become dirty or damaged. ● Do not attempt to operate the system in extreme temperature conditions [below ⫺4°F (⫺20°C) and above 158°F (70°C)] ● Do not attempt to operate the system in extreme humidity conditions (less than 10% or more than 75%).
BLUETOOTH® HANDS-FREE PHONE SYSTEM WITHOUT NAVIGATION SYSTEM (if so equipped) WARNING ● Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation. ● If you are unable to devote full attention to vehicle operation while talking on the phone, pull off the road to a safe location and stop your vehicle.
phone module when the ignition switch is placed in the ON position with the previously connected cellular phone turned on and carried in the vehicle. You can connect up to 5 different Bluetooth® cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time. Before using the Bluetooth® Hands-Free Phone System, refer to the following notes.
IC Regulatory information Initialization Giving voice commands – Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. When the ignition switch is placed in the ON position, NISSAN Voice Recognition is initialized, button is which takes a few seconds.
● You can cancel a command when the system is waiting for a response by saying, “Cancel” or “Quit.” The system announces “Cancel” and ends the VR session. You can button on the also press and hold the steering wheel for 5 seconds at any time to end the VR session. Whenever the VR session is cancelled, a double beep is played to indicate you have exited the system.
You can also use the button to interrupt the system feedback and give a command at once. See “List of voice commands” and “During a call” in this section for more information. LHA2566 CONTROL BUTTONS The control buttons for the Bluetooth® HandsFree Phone System are located on the steering wheel. PHONE/SEND Press the button to initiate a VR session or answer an incoming call.
1. Press the button on the steering wheel. The system announces the available commands. A . The system ac2. Say: “Connect phone” 䊊 knowledges the command and announces the next set of available commands. B . The system acknowl3. Say: “Add phone” 䊊 edges the command and asks you to initiate C. connecting from the phone handset 䊊 The connecting procedure of the cellular phone varies according to each cellular phone model. See the cellular phone Owner’s Manual for details. You can also visit www.nissanusa.
LIST OF VOICE COMMANDS Main Menu “Call” B (7 or 10 Digits) 䊊 “Call” Main Menu “Call” “Phonebook” A (A Name) 䊊 “Recent Calls” “Phone Number” B (7 or 10 Digits) 䊊 “Connect Phone” C “Special Number” 䊊 When you press and release the button on the steering wheel, you can choose from the commands on the Main Menu. The following pages describe these commands and the commands in each sub-menu. A (A Name) 䊊 Remember to wait for the tone before speaking.
During a call During a call there are several command options button on the steering available. Press the wheel to mute the receiving voice and enter commands. ● “Help” — The system announces the available commands. ● “Cancel/Quit” — The system announces “Cancel,” ends the VR session and returns to the call. ● “Send” — Use the Send command to enter numbers, “*” or “#” during a call. For example, if you were directed to dial an extension by an automated system: Say: “Send one two three four.
Enter a phone number by voice command: C “List Names” 䊊 For example, say: “five five five one two one two.” See “How to say numbers” in this section for more information. Use the List Names command to hear all the names in the phonebook. To transfer a phone number stored in the cellular phone’s memory: Say “Transfer entry.” The system acknowledges the command and asks you to initiate the transfer from the phone handset.
B “Record Name” 䊊 C “Missed” 䊊 A “Add Phone” 䊊 The system allows you to record custom voice tags for contact names in the phonebook that the vehicle has difficulty recognizing. This feature can also be used to record voice tags to directly dial an entry with multiple numbers. Up to 40 voice tags can be recorded to the system. Use the Missed command to list the calls made to the vehicle that were not answered. Use the Add Phone command to add a phone to the vehicle.
VOICE ADAPTATION (VA) MODE Voice Adaptation allows up to two out-of-dialect users to train the system to improve recognition accuracy. By repeating a number of commands, the users can create a voice model of their own voice that is stored in the system. The system is capable of storing a different voice adaptation model for each connected phone. Training procedure The procedure for training a voice is as follows. 1. Position the vehicle in a reasonably quiet outdoor location. 2.
● outgoing ● go back ● call three one nine oh two ● call five six two eight zero ● nine seven pause pause three oh eight ● dial six six four three seven ● cancel MANUAL CONTROL ● call back number ● correction While using the voice recognition system, it is possible to select menu options by using the steering wheel controls instead of speaking voice commands. This can be especially helpful if the noise of driving makes it difficult for the voice recognition system to accurately interpret commands.
TROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty. If problems are encountered, try the following solutions. Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved. Symptom System fails to interpret the command correctly. The system consistently selects the wrong entry from the phone book. Solution 1. Ensure that the command is valid. See “List of voice commands” in this section. 2.
BLUETOOTH® HANDS-FREE PHONE SYSTEM WITH NAVIGATION SYSTEM (if so equipped) WARNING ● Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation. ● If you are unable to devote full attention to vehicle operation while talking on the phone, pull off the road to a safe location and stop your vehicle.
phone module when the ignition switch is placed in the ON position with the connected cellular phone turned on and carried in the vehicle. You can register up to 5 different Bluetooth® cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time. NISSAN Voice Recognition system supports the phone commands, so dialing a phone number using your voice is possible. For more details, see “NISSAN Voice Recognition System” in this section.
REGULATORY INFORMATION FCC Regulatory information – CAUTION: To maintain compliance with FCC’s RF exposure guidelines, use only the supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations. – Operation is subject to the following two conditions: 1. This device may not cause interference and 2. this device must accept any interference, including interference that may cause undesired operation of the device.
Menu Item Bluetooth ON/OFF On Off Connect Bluetooth Yes Cancel No Cancel Result Allows user to switch Bluetooth on and off. Bluetooth must be on in order to connect device. Turns Bluetooth on Turns Bluetooth off Upon pressing this button, a popup box will appear on the screen, prompting you to confirm that the connection is for the phone system. Select the ⬙Yes⬙ key. Confirms that you are connecting a Bluetooth device. Upon pressing this button, the following message will appear on screen.
VEHICLE PHONEBOOK This vehicle has two phonebooks available for your use. Depending on your phone, the system may automatically download your entire cell phone’s phonebook into the “Handset Phonebook”. For the details on downloading your Menu Item Copy from Call History Copy from the Handset Enter Number by Keypad Ok Entry # Name Number Type Voicetag Store OK phonebook, see “Handset Phonebook”, in this section.
Press the button on the steering wheel and then select the ⬙Vehicle Phonebook⬙ key. Next, select the desired entry from the displayed list. Select the ⬙Edit⬙ key. Menu Item Entry # Name Number Type Voicetag Result Changes the displayed number of the selected entry Edit the name of the entry using the keypad displayed on the screen Edit the phone number using the keypad displayed on the screen Select the icon from the icon list Confirm and store the voicetag.
To transfer the handset phonebook to the vehicle manually, follow these steps: HANDSET PHONEBOOK Many phones will support an automatic download of the cellular phone’s phonebook. Since this method allows for up to 1000 numbers to be stored and entries are automatically assigned voice tags by the system, this is a useful function for easy dialing supported by the Voice Recognition system. 1. Press the SETTING button on the control panel. 2. Select the “Phone” key. 3.
MAKING A CALL Press the button on the steering wheel. The ⬙Phone⬙ screen will appear on the display. Select one of the following options to make a call: Menu Item Vehicle Phonebook Call History Handset Phonebook Dial Number Result Select the name from an entry stored in the vehicle phonebook. Dialing commences immediately. Select the name from the incoming or outgoing call history. Dialing commences immediately. Select the name from an entry stored in the handset phonebook. Dialing commences immediately.
RECEIVING A CALL When you hear a phone ring, the display will change to phone mode.
DURING A CALL There are some options available during a call. Select one of the following displayed on the screen, if necessary: Menu Item Hang Up Use Handset Mute Cancel Mute Keypad Note Switch Call Result Finish the call. If pressed while another caller is on hold, current call will be ended and user will be able to speak to the caller that was previously on hold. Transfer the call to the cellular phone. Mute your voice to the person. This will appear after the ⬙Mute⬙ key is selected.
PHONE SETTINGS To set up the Bluetooth Hands-Free Phone System to your perferred settings, press the SETTING button on the control panel and select the ⬙Phone⬙ key on the display. Menu Item Edit Vehicle Phonebook Delete Phonebook Download Handset Phonebook Volume and Ringtone Automatic Hold Vehicle Ringtone Auto Downloaded Result See ⬙Vehicle Phonebook⬙ in this section for adding, editing, and deleting contacts in the vehicle phonebook. Delete a phonebook stored on the system.
BLUETOOTH SETTINGS To set up the Bluetooth Hands-Free Phone System to your preferred settings, press the SETTING button on the control panel and select the ⬙Bluetooth⬙ key on the display. Menu Item Bluetooth Connect Bluetooth Connected Devices Edit Bluetooth Info Replaced Connected Phone Result Turn the Bluetooth system on or off. See ⬙Connecting Procedure⬙ in this section for more information about connecting a phone. Display a list of the Bluetooth devices connected to the system.
CALL VOLUME Adjusting the incoming or outgoing call volume may improve clarity if reception between callers is unclear. To access the volume settings, press the SETTING button, then select ”Volume and Beeps”.
NISSAN VOICE RECOGNITION SYSTEM (if so equipped) NISSAN Voice Recognition allows hands-free operation of the systems equipped on this vehicle, such as phone and vehicle information. There are two voice recognition modes of operation available. They are: ● Standard Mode ● Alternate Command Mode In Standard Mode (the factory default setting), commands that are available are always shown on the display and announced by the system.
Menu Item Getting Started Let’s Practice Try again Done Using the Address Book Finding a Street Address Placing Calls Help on Speaking Result The following message will appear: ⬙With voice recognition, you can use voice commands to control navigation, audio, phone, and other functions. To start the voice recognition system, push the TALK switch on the steering wheel, then say a command after the tone⬙ Initiates a practice session that demonstrates how to improve voice recognition by the system.
Voice recognition settings The available settings of the NISSAN Voice Recognition system are described. 1. Press the SETTING button on the control panel 2. Select ”Others” key 3. Select the “Voice Recognition” key You can confirm the page by scrolling the screen using the NISSAN controller.
USING THE SYSTEM Initialization When the ignition switch is placed in the ON position, NISSAN Voice Recognition is initialized, which takes a few seconds. When completed, the system is ready to accept voice commands. If switch is pressed before the initializathe tion completes, voice commands will not be accepted. Please wait until the NISSAN Voice Recognition initialization is completed.
How to speak numbers Improving Recognition of Phone numbers: ● Say a command after the tone. Voice commands cannot be accepted when the icon . is Voice Recognition requires a certain way to speak numbers when giving voice commands. Refer to the following examples. ● Commands that are available are always shown on the display and spoken through voice menu prompts. Commands other than those that are displayed are not accepted. Please follow the prompts given by the system.
Standard Mode command list Category Command: COMMAND Phone Navigation Information Audio Help ACTION Displays Phone function commands. Displays Navigation function commands. Displays Vehicle Information. Displays Audio commands. Displays User Guide. Phone Command: COMMAND Dial Number Change Number Vehicle Phonebook Handset Phonebook Call History International Call ACTION Makes a call to a spoken phone number up to 10 digits.
Vehicle Information Command: COMMAND Fuel Economy Maintenance Traffic Info. Where am I? ACTION Displays Fuel Economy information. Displays Maintenance information. Turns the traffic information system on and off. Displays current vehicle location. Audio Command: COMMAND AM FM XM CD ACTION Changes the audio system mode to AM radio. Changes the audio system mode to FM radio. Changes the audio system mode to satellite radio. Changes the audio system mode to CD.
6. The system announces, “Please say the next three digits or dial, or say change number.” Voice command examples Some basic voice command examples are described here. 7. Say “662”. 8. The system announces, “Please say the last four digits or say change number.” For navigation system commands, see the separate Navigation System Owner’s Manual. 9. Say “6200”. 10. The system announces, “Dial or Change Number?” 11. Say “Dial”. 12. The system makes a call to 800-662- 6200.
● If you say “Change Number” during phone number entry, the system will automatically request that you repeat the number using the 3-3-4 format. In this case please say the area code first and then follow the prompts. 7. The system makes a call to 011-81-111222-3333. NOTE: Any digit input format is available in the International Number input process, as well as the special characters such as star (*), pound (#), and plus (+). ● Do not add a “1” in front of the area code when speaking phone numbers.
Please note that in this mode the recognition success rate may be affected as the number of available commands and ways of speaking each command are increased. You can turn this mode ON or OFF. When this mode is activated, the Voice Recognition Settings will change to show more options.
Alternate Command Mode command list Phone Command: COMMAND Dial Number Vehicle Phonebook Handset Phonebook International Call Call Incoming Calls Outgoing Calls Missed Calls ACTION Makes a call to a spoken phone number up to 10 digits. Makes a call to a contact in the vehicle phonebook. Makes a call to a contact in the handset phonebook. Makes an international call by allowing more than 10 digits to be spoken, as well as star (*), pound (#), and plus (+).
COMMAND Birdview Map Planview Map North Up Heading Up Zoom In <1 to 13> Zoom Out <1 to 13> Guidance Voice ON/OFF Guide Voice Repeat ACTION Changes the Map display to Birdview. Changes the Map display to a 2-dimensional view. Changes the Map display to keep north pointing up on the screen. Changes the Map display to keep the direction of the vehicle pointing up on the screen. Changes the map scale to a smaller number. Changes the map scale to a larger number. Turns the navigation voice guidance on or off.
Displaying user guide 1. Press the INFO button on the control panel. You can confirm how to use voice commands by accessing a simplified User Guide, which contains basic instructions and tutorials for several voice commands. 2. Select the “Voice Recognition” key. Menu Item Getting Started Let’s Practice Using the Address Book Finding a Street Address Placing Calls Help on Speaking Voice Recognition Settings Adapting the System to Your Voice 3. Select the “User Guide” key. 4. Select an item.
Operating tips ● Say a command after the tone. Voice commands cannot be accepted when the icon . is ● If the command is not recognized, the system repeats the announcement. Repeat the command in a clear voice. ● Say “Back” when promptedl to return to the previous screen. LHA2479 LHA1345 button located 2. A list of commands appears on the screen, and the system announces, “Please say a command from the displayed list or say Help to show all commands.” Giving voice commands 1.
● To minimize the amount of prompts spoken by the system in Alternate Command Mode, use the Minimize Voice Feedback function. To access the Minimize Voice Feedback function press the SETTING button, then select the “Others” key. Then select the “Voice Recognition” key. How to speak numbers Voice Recognition requires a certain way to speak numbers when giving voice commands. Refer to the following examples. General rule: ● Only single digits 0 (zero) to 9 can be used.
5. Select the user whose voice is to be memorized by the system. 6. Select a category to be learned by the system from the following list: Edit Name: ● Navigation Edit the user name using the keypad displayed on the screen. ● Audio SPEAKER ADAPTATION FUNCTION The Voice Recognition system has a function to learn the user’s voice for better voice recognition performance. The system can memorize the voices of up to three persons. Having the system learn the user’s voice 1.
TROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty. If problems are encountered, follow the solutions given in this guide for the appropriate error. Where the solutions are listed by number, try each solution in turn, starting with number one, until the problem is resolved. Symptom/error message Displays “COMMAND NOT RECOGNIZED” or the system fails to interpret the command correctly. Solution 1.
MEMO Monitor, climate, audio, phone and voice recognition systems 4-161
5 Starting and driving Precautions when starting and driving. . . . . . . . . . . . . . . . 5-2 Exhaust gas (carbon monoxide) . . . . . . . . . . . . . . . . . . 5-2 Three-way catalyst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Tire Pressure Monitoring System (TPMS). . . . . . . . . . 5-3 On-pavement and off-road driving precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 Avoiding collision and rollover . . . . . . . . . . . . . . . . . . . .
Special winter equipment. . . . . . . . . . . . . . . . . . . . . . . 5-33 Driving on snow or ice . . . . . . . . . . . . . . . . . . . . . . . . . 5-33 Engine block heater (if so equipped) . . . . . . . . . . . . .
PRECAUTIONS WHEN STARTING AND DRIVING WARNING ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.
WARNING ● The exhaust gas and the exhaust system are very hot. Keep people, animals or flammable materials away from the exhaust system components. ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. CAUTION ● Do not use leaded gasoline. Deposits from leaded gasoline will seriously reduce the three-way catalyst’s ability to help reduce exhaust pollutants. ● Keep your engine tuned up.
Additional information: ● The TPMS does not monitor the tire pressure of the spare tire. ● The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving). ● The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted.
● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. ● Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.
Operation: 1. Add air to the tire. 2. After a few seconds, the hazard indicators will start flashing. 3. When the designated pressure is reached, the horn beeps once and the hazard indicators stop flashing. 4. Perform the above steps for each tire. ● If the tire is over-inflated more than approximately 4 psi (30 kPa), the horn beeps and the hazard indicators flash 3 times. To correct the pressure, push the core of the valve stem on the tire briefly to release pressure.
slide sideways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over-the-counter drugs which may cause drowsiness). Always wear your seat belt as outlined in the “Safety – Seats, seat belts and supplemental restraint system” section of this manual, and also instruct your passengers to do so. Seat belts help reduce the risk of injury in collisions and rollovers.
3. When appropriate, slowly release the accelerator pedal to gradually slow the vehicle. 4. Gradually steer the vehicle to a safe location off the road and away from traffic if possible. 5. Lightly apply the brake pedal to gradually stop the vehicle. 6. Turn on the hazard warning flashers and either contact a roadside emergency service to change the tire or see “Changing a flat tire” in the “In case of emergency” section of this manual.
● Do not shift gears while driving on downhill grades as this could cause loss of control of the vehicle. ● Stay alert when driving to the top of a hill. At the top there could be a drop-off or other hazard that could cause an accident. ● If your engine stalls or you cannot make it to the top of a steep hill, never attempt to turn around. Your vehicle could tip or roll over. Always back straight down in R (Reverse) gear and apply brakes to control your speed.
PUSH-BUTTON IGNITION SWITCH ● Failure to operate this vehicle correctly could result in loss of control and/or a rollover accident. ● Always use tires of the same type, size, brand, construction (bias, bias-belted, or radial), and tread pattern on all four wheels. Install tire chains on the front wheels when driving on slippery roads and drive carefully. ● Be sure to check the brakes immediately after driving in mud or water. See “Brake system” later in this section for “Wet brakes”.
The ignition lock is designed so that the ignition switch position cannot be switched to OFF until the shift lever is moved to the P (Park) position. The operating range of the engine start function 1 . is inside of the vehicle 䊊 ● The luggage area is not included in the operating range, but the Intelligent Key may function.
ACC (Accessories): This position activates electrical accessories, such as the radio, when the engine is not running. ACC has a battery saver feature that will turn the ignition switch to the OFF position after a period of time under the following conditions: ● all doors are closed. The battery saver feature will be cancelled if any of the following occur: ● any door is opened. ● shift lever is moved out of the P (Park) position. ● ignition switch changes position. CAUTION ● shift lever is in P (Park).
BEFORE STARTING THE ENGINE 3. Touch the ignition switch with the Intelligent Key as illustrated. (A chime will sound.) After step 3 is performed, when the ignition switch is pushed without depressing the brake pedal, the ignition switch position will change to ACC. 4. Push the ignition switch while depressing the brake pedal within 10 seconds after the chime sounds. The engine will start.
STARTING THE ENGINE 1. Apply the parking brake. 2. Move the shift lever to P (Park) or N (Neutral). P (Park) is recommended. The starter is designed not to operate if the shift lever is in any of the driving positions. 3. Push the ignition switch to the ON position. Depress the brake pedal and push the ignition switch to start the engine. To start the engine immediately, push and release the ignition switch while depressing the brake pedal with the ignition switch in any position.
DRIVING THE VEHICLE CONTINUOUSLY VARIABLE TRANSMISSION (CVT) The Continuously Variable Transmission (CVT) in your vehicle is electronically controlled to produce maximum power and smooth operation. The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment.
WARNING Apply the parking brake if the shift lever is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage. CAUTION Use the P (Park) or R (Reverse) position only when the vehicle is completely stopped.
C and move the 5. Press the shift lever button 䊊 D shift lever to the N (Neutral) position 䊊 while holding down the shift lock release. The vehicle may be moved to the desired location. Replace the removed shift lock release cover after the operation. If the shift lever cannot be moved out of the P (Park) position, have a NISSAN dealer check the CVT system as soon as possible.
PARKING BRAKE Fail-safe If the vehicle is driven under extreme conditions, such as excessive wheel spinning and subsequent hard braking, the fail-safe system may be activated. The MIL may come on to indicate the fail-safe mode is activated, see “Malfunction Indicator Light (MIL)” in the “Instrument and controls” section. This will occur even if all electrical circuits are functioning properly. In this case, place the ignition switch in the OFF position and wait for 10 seconds.
CRUISE CONTROL ● If the SET indicator light blinks, push the cruise control ON·OFF switch off and have the system checked by a NISSAN dealer. ● The SET indicator light may blink when the cruise control ON·OFF switch is pushed ON while pushing the ACCEL/RES, COAST/SET, or CANCEL switch. To properly set the cruise control system, use the following procedures. WARNING Do not use the cruise control when driving under the following conditions: LSD0158 To engage: Firmly depress the parking brake. To release: 1.
CRUISE CONTROL OPERATIONS The cruise control allows driving at a speed between 25 - 89 MPH (40 - 144 km/h) without keeping your foot on the accelerator pedal. To turn on the cruise control, push the ON·OFF switch on. The CRUISE indicator light in the vehicle information display will illuminate. To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. The SET indicator light in the vehicle information display will illuminate.
BREAK-IN SCHEDULE CAUTION During the first 1,200 miles (2,000 km), follow these recommendations to obtain maximum engine performance and ensure the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in shortened engine life and reduced engine performance. ● Avoid driving for long periods at constant speed, either fast or slow, and do not run the engine over 4,000 rpm. ● Do not accelerate at full throttle in any gear. ● Avoid quick starts.
INCREASING FUEL ECONOMY 6. Plan for the Shortest Route ● Utilize a map or navigation system to determine the best route to save time 7. Avoid Idling ● Shutting off your engine when safe for stops exceeding 30–60 seconds saves fuel and reduces emissions 8. Buy an Automated Pass for Toll Roads ● Automated passes permit drivers to use special lanes to maintain cruising speed through the toll and avoid stopping and starting 9.
INTELLIGENT 4WD (if so equipped) ● AUTO – Turn the 4WD mode switch to the neutral (AUTO) position. The Four-Wheel Drive (4WD) AUTO indicator light in the vehicle information display illuminates. 4X4I SYSTEM OPERATION LIC2399 4WD shift switch The Four-Wheel Drive (4WD) system is used to select the 2WD (Two-Wheel Drive), AUTO or LOCK mode depending on the driving conditions. ● LOCK – To engage the LOCK mode, turn the 4WD mode switch to the LOCK position.
4WD mode Wheels driven 4WD mode indicator light Use conditions 2WD Front only – This mode is used when driving on a normal road *1 2WD For driving on dry paved roads. AUTO Distribution of torque to the front and rear wheels changes automatically depending on road conditions encountered. This results in improved driving stability. LOCK Four-wheel drive *2 *3 AUTO For driving on paved or slippery roads. LOCK For driving on rough roads.
CAUTION ● Depending on the driving condition, the 4WD mode may automatically change from 2WD to 4WD even when the 2WD mode is selected. If this occurs while driving, the 4WD mode indicator light will not illuminate. ● Do not start the engine with the 4WD mode switch in any mode in the following cases: – when the vehicle is placed on a freeroller or jacking up the vehicle with the front tires raised and the rear tires on the ground.
PARKING/PARKING ON HILLS A ● HEADED DOWNHILL WITH CURB: 䊊 Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb. B ● HEADED UPHILL WITH CURB: 䊊 Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb. ● HEADED UPHILL OR DOWNHILL, NO C CURB: 䊊 WSD0050 WARNING ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.
POWER STEERING WARNING ● If the engine is not running or is turned off while driving, the power assist for the steering will not work. Steering will be harder to operate. ● When the power steering warning light illuminates with the engine running, there will be no power assist for the steering. You will still have control of the vehicle but the steering will be harder to operate. Have the power steering system checked by a NISSAN dealer.
WARNING ● While driving on a slippery surface, be careful when braking, accelerating or downshifting. Abrupt braking or accelerating could cause the wheels to skid and result in an accident. ● If the engine is not running or is turned off while driving, the power assist for the brakes will not work. Braking will be harder. Wet brakes When the vehicle is washed or driven through water, the brakes may get wet.
VEHICLE DYNAMIC CONTROL (VDC) SYSTEM WARNING Normal operation Do not pump the brake pedal. Doing so may result in increased stopping distances. The ABS operates at speeds above 3 - 6 MPH (5 - 10 km/h). The speed varies according to road conditions. Self-test feature When the ABS senses that 1 or more wheels are close to locking up, the actuator rapidly applies and releases hydraulic pressure. This action is similar to pumping the brakes very quickly.
When the VDC system operates, the indicator in the instrument panel flashes so note the following: indicator flashes if this occurs. All other VDC indicator will not functions are off and the flash. ● The road may be slippery or the system may determine some action is required to help keep the vehicle on the steered path. The VDC system is automatically reset to on when the ignition switch is placed in the off position then back to the on position.
● When driving on extremely inclined surfaces such as higher banked corners, the VDC system may not operate propindicator may flash or erly and the and indicator both the lights may illuminate. Do not drive on these types of roads. ● When driving on an unstable surface such as a turntable, ferry, elevator or indicator may flash or ramp, the and indicator both the lights may illuminate. This is not a malfunction. Restart the engine after driving onto a stable surface.
HILL START ASSIST SYSTEM ● When driving on an unstable surface such as a turntable, ferry, elevator or ramp, the VDC warning light may illuminate. This is not a malfunction. Restart the engine after driving onto a stable surface. ● If wheels or tires other than the NISSAN recommended ones are used, the VDC system may not operate properly and the VDC warning light may illuminate. ● The VDC system is not a substitute for winter tires or tire chains on a snow covered road.
COLD WEATHER DRIVING FREEING A FROZEN DOOR LOCK To prevent a door lock from freezing, apply deicer through the key hole. If the lock becomes frozen, heat the key before inserting it into the key hole, or use the NISSAN Intelligent Key®. ANTI-FREEZE In the winter when it is anticipated that the temperature will drop below 32°F (0°C), check the anti-freeze to assure proper winter protection. For details, see “Engine cooling system” in the “Maintenance and do-it-yourself” section of this manual.
● Allow more stopping distance under these conditions. Braking should be started sooner than on dry pavement. ● Allow greater following distances on slippery roads. ● Watch for slippery spots (glare ice). These may appear on an otherwise clear road in shaded areas. If a patch of ice is seen ahead, brake before reaching it. Try not to brake while on the ice, and avoid any sudden steering maneuvers. ● Do not use the cruise control on slippery roads. ● Snow can trap dangerous exhaust gases under your vehicle.
6 In case of emergency Emergency engine shut off . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Hazard warning flasher switch . . . . . . . . . . . . . . . . . . . . . . 6-2 Flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Tire Pressure Monitoring System (TPMS). . . . . . . . . . 6-3 Changing a flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EMERGENCY ENGINE SHUT OFF HAZARD WARNING FLASHER SWITCH To shut off the engine in an emergency situation while driving, perform the following procedure: The flashers will operate with the ignition switch placed in any position. – Rapidly push the push-button ignition switch 3 consecutive times in less than 1.5 seconds, or Some state laws may prohibit the use of the hazard warning flasher switch while driving. – Push and hold the push-button ignition switch for more than 2 seconds.
FLAT TIRE TIRE PRESSURE MONITORING SYSTEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit, and the Tire Pressure Low - Add Air warning appears in the vehicle information display, one or more of your tires is significantly under-inflated.
4. Turn off the engine. 5. Raise the hood to warn other traffic and to signal professional road assistance personnel that you need assistance. 6. Have all passengers get out of the vehicle and stand in a safe place, away from traffic and clear of the vehicle. WARNING ● Make sure the parking brake is securely applied and the CVT is shifted into P (Park). ● Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous.
LCE2036 2. Remove the jack and tool kit cover by lifting up using the handles. LCE2037 B. 3. Remove the tool kit 䊊 ● To release the tool kit, release the hook C. and eye straps 䊊 LCE2038 4. Remove the jack. D , to ● The jack is secured by a fastener 䊊 release the fastener assemble the extenE into the wheel nut wrench 䊊 F as sion 䊊 illustrated and rotate counterclockwise to release.
CAUTION ● Make sure safety cable is coiled above spare tire when reinstalling spare tire/wheel. LCE2039 H to the 6. Insert the spare tire winch socket 䊊 lowering mechanism nut. 7. To lower the spare tire, insert the wheel nut F to the extension 䊊 E and insert wrench 䊊 H the T-shaped end to the winch socket 䊊 and rotate counterclockwise. 8. After removing the spare tire from under the vehicle, be sure to crank the cable up to stow it.
2. Place the jack directly under the jack-up point as illustrated so the top of the jack contacts the vehicle at the jack-up point. The jack-up points are indicated by stamped arrows on the side of the frame. LCE2048 LCE0087 The jack should be used on firm and level ground. 3. Install the assembled jack rod into the jack as shown. 4. To lift the vehicle, securely hold the jack lever and rod. Carefully raise the vehicle until the tire clears the ground.
4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely D, A,䊊 B,䊊 C,䊊 in the sequence illustrated (䊊 E ). Lower the vehicle completely. 䊊 WARNING ● Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident.
JUMP STARTING Adjust tire pressure to the COLD pressure. COLD pressure: After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km). COLD tire pressures are shown on the tire and loading information label affixed to the driver side center pillar. 5. Securely store the flat tire and jacking equipment in the vehicle. 6. Close the liftgate. WARNING ● Always make sure that the spare tire and jacking equipment are properly secured after use.
● Whenever working on or near a battery, always wear suitable eye protectors (for example, goggles or industrial safety spectacles) and remove rings, metal bands, or any other jewelry. Do not lean over the battery when jump starting. ● Do not attempt to jump start a frozen battery. It could explode and cause serious injury. ● Your vehicle has an automatic engine cooling fan. It could come on at any time. Keep hands and other objects away from it. WCE0054 WARNING Always follow the instructions below.
PUSH STARTING CAUTION ● Always connect positive (⫹) to positive (⫹) and negative (⫺) to body ground (for example, strut mounting bolt, engine lift bracket, etc.) — not to the battery. ● Make sure the jumper cables do not touch moving parts in the engine compartment and that the cable clamps do not contact any other metal. 5. Start the engine of the booster vehicle and let it run for a few minutes. 6.
TOWING YOUR VEHICLE 3. Get out of the vehicle. Look and listen for steam or coolant escaping from the radiator before opening the hood. (If steam or coolant is escaping, turn off the engine.) Do not open the hood further until no steam or coolant can be seen. 4. Open the engine hood. WARNING If steam or water is coming from the engine, stand clear to prevent getting burned. 5. Visually check drive belts for damage or looseness. Also check if the cooling fan is running.
For information about towing your vehicle behind a recreational vehicle (RV), refer to “Flat towing” in the “Technical and consumer information” section of this manual. TOWING RECOMMENDED BY NISSAN LCE2049 Four-wheel drive models NISSAN recommends that towing dollies be used when towing your vehicle or place the vehicle on a flat bed truck as illustrated. CAUTION Never tow 4WD models with any of the wheels on the ground as this may cause serious and expensive damage to the powertrain.
WARNING ● Never tow your vehicle with the front wheels on the ground or four wheels on the ground (forward or backward), as this may cause serious and expensive damage to the transmission. If it is necessary to tow the vehicle with the rear wheels raised always use towing dollies under the front wheels.
VEHICLE RECOVERY (freeing a stuck vehicle) Pulling a stuck vehicle WARNING To avoid vehicle damage, serious personal injury or death when recovering a stuck vehicle: ● Contact a professional towing service to recover the vehicle if you have any questions regarding the recovery procedure. ● Attach recovery devices only to main structural members of the vehicle or the recovery hooks. ● Do not use the vehicle tie-downs to tow or free a stuck vehicle.
MEMO 6-16 In case of emergency
7 Appearance and care Cleaning exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Removing spots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Underbody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Glass . . . . . . . . . . . . . . . . . . . . . . .
CLEANING EXTERIOR In order to maintain the appearance of your vehicle, it is important to take proper care of it. To protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage from acid rain. ● after driving on coastal roads. ● when contaminants such as soot, bird droppings, tree sap, metal particles or bugs get on the paint surface. ● when dust or mud builds up on the surface.
REMOVING SPOTS CAUTION Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store. When cleaning the inside of the windows, do not use sharp-edged tools, abrasive cleaners or chlorine-based disinfectant cleaners. They could damage the electrical conductors, radio antenna elements or rear window defroster elements.
CLEANING INTERIOR Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft bristled brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry, soft cloth. Regular care and cleaning is required in order to maintain the appearance of the leather. Before using any fabric protector, read the manufacturer’s recommendations.
FLOOR MATS WARNING To avoid potential pedal interference that may result in a collision or injury: ● NEVER place a floor mat on top of another floor mat in the driver front position. ● Use only genuine NISSAN floor mats specifically designed for use in your vehicle model. See your NISSAN dealer for more information. ● Properly position the mats in the floorwell using the floor mat positioning aid. See ⴖFloor mat positioning aidⴖ in this section.
CORROSION PROTECTION Genuine NISSAN floor mats have been specially designed for your vehicle model. The floor mats have grommet holes incorporated in them. Position each mat by placing the floor mat bracket hook through the floor mat grommet holes while centering the mat in the floorwell. CLEANING THE SEAT TRACKS Periodically check to make certain the mats are properly positioned. Clean periodically with a high-powered vacuum cleaner. Dirt and debris may reduce the ability to adjust the seat.
Temperature CAUTION Air pollution ● NEVER remove dirt, sand or other debris from the passenger compartment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom. Industrial pollution, the presence of salt in the air in coastal areas, or heavy road salt use accelerates the corrosion process. Road salt also accelerates the disintegration of paint surfaces. ● Never allow water or other liquids to come in contact with electronic components inside the vehicle as this may damage them.
MEMO 7-8 Appearance and care
8 Maintenance and do-it-yourself Maintenance requirements. . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 General maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Explanation of general maintenance items . . . . . . . . . 8-2 Maintenance precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Engine compartment check locations . . . . . . . . . . . . . . . . 8-6 Engine cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE REQUIREMENTS Your NISSAN has been designed to have minimum maintenance requirements with long service intervals to save you both time and money. However, some day-to-day and regular maintenance is essential to maintain your NISSAN’s good mechanical condition, as well as its emissions and engine performance. It is the owner’s responsibility to make sure that the scheduled maintenance, as well as general maintenance, is performed.
When driving in areas using road salt or other corrosive materials, check lubrication frequently. Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Road wheel nuts (lug nuts)* When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary.
Seat belts Check that all parts of the seat belt system (for example, buckles, anchors, adjusters and retractors) operate properly and smoothly, and are installed securely. Check the belt webbing for cuts, fraying, wear or damage. Steering wheel Check for changes in the steering system, such as excessive freeplay, hard steering or strange noises. Warning lights and chimes Make sure all warning lights and chimes are operating properly.
MAINTENANCE PRECAUTIONS When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed. WARNING ● Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the vehicle from moving. Move the shift lever to P (Park).
ENGINE COMPARTMENT CHECK LOCATIONS 12. Engine oil dipstick 13. Radiator cap 14. Windshield-washer fluid reservoir NOTE: Engine cover removed for clarity. LDI2266 VQ35DE engine 1. 2. 3. 4. 5. Power steering fluid reservoir Engine coolant reservoir Drive belt location Fuse box Engine oil filler cap 8-6 Maintenance and do-it-yourself 6. 7. 8. 9. 10 11.
ENGINE COOLING SYSTEM The engine cooling system is filled at the factory with a pre-diluted mixture of 50% Genuine NISSAN Long Life Antifreeze/Coolant (blue) and 50% water to provide year-round anti-freeze and coolant protection. The antifreeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not necessary. WARNING ● Never remove the radiator or coolant reservoir cap when the engine is hot. Wait until the engine and radiator cool down.
coolant or the use of non-distilled water will reduce the life expectancy of the factory-fill coolant. Refer to the NISSAN Service and Maintenance Guide for more details. ● Avoid direct skin contact with used coolant. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible. The engine coolant reservoir is a pressurized tank. When installing the cap, tighten it until a clicking sound is heard. ● Keep coolant out of the reach of children and pets.
ENGINE OIL CAUTION Oil level should be checked regularly. Operating the engine with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty. LDI2087 CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and apply the parking brake. 2. Start the engine and let it idle until it reaches operating temperature. 3. Turn off the engine. Wait more than 10 minutes for the oil to drain back into the oil pan. 4. Remove the dipstick and wipe it clean.
If the oil filter is to be changed, remove and replace it at this time. See “Changing engine oil filter” in this section. 7. Refill engine with recommended oil through the oil filler opening, then install the oil filler cap securely. ● Waste oil must be disposed of properly. See “Capacities and recommended fuel/lubricants” in the “Technical and consumer information” section of this manual for drain and refill capacity. ● Check your local regulations.
CONTINUOUSLY VARIABLE TRANSMISSION (CVT) FLUID 5. Wipe the engine oil filter sealing surface with a clean rag. CAUTION ● Be sure to remove any old gasket material remaining on the sealing surface of the engine. Failure to do so could lead to an oil leak and engine damage. ● The dipstick must be inserted in place to prevent oil spillage from the dipstick hole when filling the engine with oil. LDI2143 CHANGING ENGINE OIL FILTER 7.
POWER STEERING FLUID BRAKE FLUID CAUTION ● Do not overfill. ● Use of a power steering fluid other than Genuine NISSAN E-PSF will prevent the power steering system from operating properly. ● Power steering fluid is poisonous and should be stored carefully in marked containers out of the reach of children. LDI2146 Check the fluid level in the reservoir. The fluid level should be checked when the fluid is cold at fluid temperatures of 32 to 86ºF (0 to 30ºC).
WINDSHIELD-WASHER FLUID Refill the reservoir more frequently when driving conditions require an increased amount of windshield-washer fluid. Recommended fluid is Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or equivalent. CAUTION ● Do not substitute engine anti-freeze coolant for windshield-washer fluid. This may result in damage to the paint. LDI2147 Check the fluid level in the reservoir. If the brake B , the brake warning fluid is below the MIN line 䊊 light will illuminate.
BATTERY ● Keep the battery surface clean and dry. Clean the battery with a solution of baking soda and water. ● Make certain the terminal connections are clean and securely tightened. ● If the vehicle is not to be used for 30 days or longer, disconnect the negative (-) battery terminal cable to prevent discharge. NOTE: Care should be taken to avoid situations that can lead to potential battery discharge and potential no-start conditions such as: 1.
Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP STARTING If jump starting is necessary, see “Jump starting” in the “In case of emergency” section of this manual. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN dealer. WDI0224 1. Remove the vent caps with a screwdriver as shown. Use a cloth to protect the battery case. LDI0302 2. Check the fluid level in each cell.
VARIABLE VOLTAGE CONTROL SYSTEM (if so equipped) DRIVE BELT The current sensor is located near the battery along the negative battery cable. If you add electrical accessories to your vehicle, be sure to ground them to a suitable body ground such as the frame or engine block area. LDI2132 CAUTION ● Do not ground accessories directly to the battery terminal. Doing so will bypass the variable voltage control system and the vehicle battery may not charge completely.
SPARK PLUGS 2. Have the belt checked regularly for condition and tension in accordance with the maintenance schedule found in your “NISSAN Service and Maintenance Guide”. WARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely. CAUTION Be sure to use the correct socket to remove the spark plugs. An incorrect socket can damage the spark plugs. If replacement is required, see your NISSAN dealer for assistance.
AIR CLEANER WINDSHIELD WIPER BLADES NOTE: CLEANING After installing a new air cleaner, make sure the air cleaner cover is seated in the housing and latch the clips. If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. WARNING LDI2090 Clean and replace the air cleaner filter according to the maintenance log shown in the “NISSAN Service and Maintenance Guide.
6. Return the wiper to its original position and release it until it has made contact with the windshield. CAUTION ● After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened. ● Make sure the wiper blades contact the glass; otherwise the arms may be damaged from wind pressure. WDI0594 REPLACING Replace the wiper blades if they are worn. 1. Lift the wiper arm away from the windshield.
BRAKES Rear window wiper blade Contact a NISSAN dealer if checking or replacement is required. If the brakes do not operate properly, have the brakes checked by a NISSAN dealer. Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes. The front and rear disc-type brakes self-adjust every time the brake pedal is applied. WARNING See a NISSAN dealer for a brake system check if the brake pedal height does not return to normal.
FUSES ENGINE COMPARTMENT CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire. If any electrical equipment does not come on, check for an open fuse. 1. Be sure the ignition switch and the headlight switch are OFF. LDI2267 LDI0456 3. Remove the fuse box cover by pushing the tab and lifting the cover up. A , replace it with a new 5. If the fuse is open 䊊 B. fuse 䊊 4.
If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and the headlight switch are OFF. 2. Open the glove box to access the fuse box cover. 3. Pull the fuse box cover to remove. 4. Remove the fuse with the fuse puller. LDI2092 PASSENGER COMPARTMENT CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.
BATTERY REPLACEMENT How to replace the extended storage switch: 1. To remove the extended storage switch, be sure the ignition switch is in the OFF or LOCK position. CAUTION Be careful not to allow children to swallow the battery or removed parts. 2. Be sure the headlight switch is in the OFF position. 3. Remove the fuse box cover. 1 found on each 4. Pinch the locking tabs 䊊 side of the storage switch. 5. Pull the storage switch straight out from the 2 .
NISSAN INTELLIGENT KEY® Replace the battery in the Intelligent Key as follows: 1. Remove the mechanical key from the Intelligent Key. A into the slit 䊊 B 2. Insert a small screwdriver 䊊 of the corner and twist it to separate the upper part from the lower part. Use a cloth to protect the casing. 3. Replace the battery with a new one. Recommended battery: CR2025 or equivalent. C 䊊 D. 4. Close the lid securely as illustrated 䊊 ● Hold the battery by the edges.
LIGHTS NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For Canada: This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
EXTERIOR AND INTERIOR LIGHTS Item Headlight assembly* High Low Park Turn Sidemarker Front fog lights (if so equipped) Daytime running lights (Canada only) Map light* Footwell light Personal lights Glove box light* Step light Courtesy light* Vanity mirror light Cargo light High-mounted stop light* Rear combination light Tail/Stop* Turn Rear sidemarker Backup (reversing)* License plate light* Wattage (W) Bulb No. 60 55 5 21 5 55 19 — 3.4 8 8 3.
1. 2 3 4. 5. 6. 7. 8. Headlight assembly Map light Personal light Fog light (if so equipped)/ Daytime running light (Canada only) (if so equipped) Cargo light Courtesy light Rear combination light License plate light Indicates bulb removal Indicates bulb installation WDI0263 Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, first remove the lens, lamp and/or cover.
WDI0670 Personal lights 1 to protect the housing. Use a cloth 䊊 8-28 Maintenance and do-it-yourself LDI2096 Vanity mirror 1 to protect the housing. Use a cloth 䊊 WDI0206 Cargo light 1 to protect the housing.
WHEELS AND TIRES If you have a flat tire, see “Flat tire” in the “In case of emergency” section of this manual. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit and the Tire Pressure Low - Add Air warning appears in the vehicle information display, one or more of your tires is significantly under-inflated.
WARNING ● Improperly inflated tires can fail suddenly and cause an accident. ● The Gross Vehicle Weight Rating (GVWR) is located on the F.M.V.S.S./C.M.V.S.S. certification label. The vehicle weight capacity is indicated on the Tire and Loading Information label. Do not load your vehicle beyond this capacity. Overloading your vehicle may result in reduced tire life, unsafe operating conditions due to premature tire failure, or unfavorable handling characteristics and could also lead to a serious accident.
4 䊊 5 䊊 6 䊊 Tire size - refer to “Tire labeling” later in this section. Spare tire size. Vehicle load limit: See loading information in the “Technical and consumer information” section. LDI2083 Tire and loading information label 1 䊊 2 䊊 Seating capacity: The maximum number of occupants that can be seated in the vehicle. Original tire size: The size of the tires originally installed on the vehicle at the factory. 3 䊊 Cold tire pressure: Inflate the tires to this pressure when the tires are cold.
4. Read the tire pressure on the gauge stem and compare to the specification shown on the Tire and Loading Information label. 5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Recheck the pressure and add or release air as needed. 6. Install the valve stem cap. LDI0393 Checking tire pressure 7. Check the pressure of all other tires, including the spare. 1. Remove the valve stem cap from the tire.
7. H: Tire speed rating. You should not drive the vehicle faster than the tire speed rating. WDI0395 Example 1 Tire size (example: P215/65R15 95H) 䊊 1. P: The “P” indicates the tire is designed for passenger vehicles (not all tires have this information). 2. Three-digit number (215): This number gives the width in millimeters of the tire from sidewall edge to sidewall edge. 3. Two-digit number (65): This number, known as the aspect ratio, gives the tire’s ratio of height to width. 4.
3 Tire ply composition and material 䊊 The number of layers or plies of rubbercoated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. 4 Maximum permissible inflation pres䊊 sure WDI0396 Example 2 TIN (Tire Identification Number) for a 䊊 new tire (example: DOT XX XX XXX XXXX) 1. DOT: Abbreviation for the “Department Of Transportation”.
7 The word “radial” 䊊 The word “radial” is shown if the tire has radial structure. 8 Manufacturer or brand name 䊊 Manufacturer or brand name is shown.
Generally, snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire. If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires.
Wheel nut tightening torque: 83 ft-lb (113 N·m) ● The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced. The wheel nuts must be kept tightened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval. ● Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified technician because some tire damage may not be obvious.
Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in “Wheels and tires” in the “Technical and consumer information” section of this manual.
If excessive tire wear is found, it is recommended that all four tires be replaced with tires of the same size, brand, construction and tread pattern. The tire pressure and wheel alignment should also be checked and corrected as necessary. Contact a NISSAN dealer. Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as required.
MEMO 8-40 Maintenance and do-it-yourself
9 Technical and consumer information Capacities and recommended fuel/lubricants . . . . . . . . . 9-2 Fuel recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Engine oil and oil filter recommendations . . . . . . . . . . 9-5 Air conditioner system refrigerant and oil recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7 Engine . . . . . . . . . . . . . . . . . . . . . .
CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity.
FUEL RECOMMENDATION Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91). CAUTION ● Only vehicles with the E-85 filler door label can operate on E-85. Fuel system or other damage can occur if E-85 is used in vehicles that are not designed to run on E-85. ● Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage.
● If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol). It should also contain a suitable amount of appropriate cosolvents and corrosion inhibitors. If not properly formulated with appropriate cosolvents and corrosion inhibitors, such methanol blends may cause fuel system damage and/or vehicle performance problems. At this time, sufficient data is not available to ensure that all methanol blends are suitable for use in NISSAN vehicles.
Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be operated before the next oil change. Choosing an oil viscosity other than that recommended could cause serious engine damage.
Your engine was filled with a high-quality engine oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle.
SPECIFICATIONS ENGINE Model Type Cylinder arrangement Bore x Stroke Displacement Firing order VQ35DE Gasoline, 4-cycle, DOHC 6-cylinder, V-block, Slanted at 60° in (mm) 3.760 x 3.205 (95.5 x 81.4) cu in (cm3) 213.45 (3,498) 1–2–3–4–5–6 Idle speed CVT (in “N” position) Ignition timing (degree B.T.D.C. at idle speed) CO % at idle Spark plug Spark plug gap (Nominal) Camshaft operation This spark ignition system complies with the Canadian standard ICES-002. No adjustment is necessary. FXE22HR-11 in (mm) 0.
WHEELS AND TIRES Wheel type Aluminum DIMENSIONS AND WEIGHTS Offset in (mm) Size 1.97 (50) 18 x 7.5J 1.97 (50) 20 x 7.5J Spare Wheel - Steel Tire size 18 x4T 235/65R18 235/55R20 Spare tire 9-8 Technical and consumer information T165/90D18 Overall length Overall width Overall height without roof rack with roof rack Front and Rear Track Wheelbase Gross vehicle weight rating Gross axle weight rating Front Rear in (mm) in (mm) 197.2 (5,008.4) 77.2 (1,960) in (mm) in (mm) in (mm) in (mm) 69.
WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY VEHICLE IDENTIFICATION When planning to drive your NISSAN vehicle in another country, you should first find out if the fuel available is suitable for your vehicle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. Therefore, avoid taking your vehicle to areas where appropriate fuel is not available.
LTI2034 ENGINE SERIAL NUMBER The number is stamped on the engine as shown. 9-10 Technical and consumer information WTI0058 WTI0167 F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL EMISSION CONTROL INFORMATION LABEL The Federal/Canadian Motor Vehicle Safety Standard (F.M.V.S.S./C.M.V.S.S.) certification label is affixed as shown.
INSTALLING FRONT LICENSE PLATE To mount the license plate, attach the license plate bracket to the front plastic finisher at the location marks (small dimples) using the screws provided. LTI0084 WTI0173 TIRE AND LOADING INFORMATION LABEL AIR CONDITIONER SPECIFICATION LABEL The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown. The air conditioner specification label is affixed to the underside of the hood as shown.
VEHICLE LOADING INFORMATION WARNING ● It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. ● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. ● Be sure everyone in your vehicle is in a seat and using a seat belt properly.
VEHICLE LOAD CAPACITY Do not exceed the load limit of your vehicle shown as “The combined weight of occupants and cargo” on the Tire and Loading Information label. Do not exceed the number of occupants shown as “Seating Capacity” on the Tire and Loading Information label. To get “the combined weight of occupants and cargo”, add the weight of all occupants, then add the total luggage weight. Examples are shown in the following illustration.
Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX lbs or XXX kg. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the XXX amount equals 1,400 lbs.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. WARNING ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury. 6.
TOWING A TRAILER LOADING TIPS ● The GVW must not exceed GVWR or GAWR as specified on the F.M.V.S.S./C.M.V.S.S. certification label. ● Do not load the front and rear axle to the GAWR. Doing so will exceed the GVWR. WARNING ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury.
Temperature conditions can also affect towing. For example, towing a heavy trailer in high outside temperatures on graded roads can affect engine performance and cause overheating. The engine protection mode, which helps reduce the chance of engine damage, could activate and automatically decrease engine power. Vehicle speed may decrease under high load. Plan your trip carefully to account for trailer and vehicle load, weather and road conditions.
Towing capacities are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers, cargo and/or optional equipment, such as the trailer hitch, will add weight to the vehicle and reduce your vehicle’s maximum towing capacity and trailer tongue load. The vehicle and trailer need to be weighed to confirm the vehicle is within the GVWR, Front GAWR, Rear GAWR, Gross Combined Weight Rating (GCWR) and Towing capacity.
To determine the available towing capacity, use the following procedure. 1. Find the GCWR for your vehicle on the ⬙Towing Load/Specification⬙ chart found later in this section. 2. Subtract the actual vehicle weight from the GCWR. The remaining amount is the available maximum towing capacity. To determine the Gross Trailer Weight, weigh your trailer on a scale with all equipment and cargo, that are normally in the trailer when it is towed.
TOWING LOAD/SPECIFICATION TOWING SAFETY Trailer hitch TOWING LOAD/SPECIFICATION CHART U.S. and Canada Maximum Towing Capacity*1 5,000lb. Maximum Tongue Load 500 lb. Maximum Gross Combined Weight Rating 10,000 lb. (2,268 kg) (227 kg) (4, 536 kg) *1: The towing capacity values are calculated assuming a base vehicle with driver and any options required to achieve the rating.
Ball mount NOTE: Trailer hitch components have specific weight ratings. Your vehicle may be capable of towing a trailer heavier than the weight rating of the hitch components. Never exceed the weight rating of the hitch components. Doing so can cause serious personal injury or property damage. The hitch ball is attached to the ball mount and the ball mount is inserted into the hitch receiver. Choose a proper class ball mount based on the trailer weight.
Class I hitch Safety chains Properly adjust the weight distributing hitch so the rear of the bumper is no higher than the measured reference height when the trailer is attached. If the rear bumper is higher than the measured reference height when loaded, the vehicle may handle unpredictably which could cause a loss of vehicle control and cause serious personal injury or property damage.
Trailer lights should comply with federal and/or local regulations. For assistance in hooking up trailer lights, contact a NISSAN dealer or reputable trailer retailer. Vehicles equipped with the optional trailer tow package are equipped with a 7-pin trailer harness connector. If your trailer is equipped with a flat 4-pin connector, an adapter will be needed to connect the trailer lights to the vehicle. Adapters are available at auto parts stores and hitch retailers.
Wire color designation for electric trailer brake controller jumper harness. WIRE COLOR WHITE BLACK WHITE GREEN LTI2045 LTI2046 2. Locate the jumper harness connector under the lower portion of the instrument panel. The connector is taped to the wiring harness 1 as indicated. 䊊 ● The connector is marked with a white tag with “elec brake conn”. NOTE Vehicle stop lamp switch to trailer brake controller. Brake controller ground (-). Trailer brake controller switched output.
● Keep the cargo load as low as possible in the trailer to keep the trailer center of gravity low. ● Lock the trailer hitch coupler with a pin or lock to prevent the coupler from inadvertently becoming unlatched. ● Load the trailer so approximately 60% of the trailer load is in the front half and 40% is in the back half. Also make sure the load is balanced side to side. ● Avoid abrupt starts, acceleration or stops.
● While going downhill, the weight of the trailer pushing on the tow vehicle may decrease overall stability. Therefore, to maintain adequate control, reduce your speed and shift to a lower gear. Avoid long or repeated use of the brakes when descending a hill, as this reduces their effectiveness and could cause overheating. Shifting to a lower gear instead provides “engine braking” and reduces the need to brake as frequently.
● When launching a boat, don’t allow the water level to go over the exhaust tail pipe or rear bumper. ● Make sure you disconnect the trailer lights before backing the trailer into the water or the trailer lights may burn out. When towing a trailer, final drive gear oil should be replaced and transmission oil/fluid should be changed more frequently. For additional information, see the “Maintenance and do-it-yourself” section earlier in this manual.
UNIFORM TIRE QUALITY GRADING DOT (Department of Transportation) Quality Grades: All passenger car tires must conform to federal safety requirements in addition to these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
EMISSION CONTROL SYSTEM WARRANTY REPORTING SAFETY DEFECTS Your NISSAN vehicle is covered by the following emission warranties: For USA For USA 1. Emission Defects Warranty 2. Emissions Performance Warranty Details of this warranty may be found with other vehicle warranties in your Warranty Information Booklet which comes with your NISSAN vehicle. If you did not receive a Warranty Information Booklet, or it is lost, you may obtain a replacement by writing to: ● Nissan North America, Inc.
READINESS FOR INSPECTION/ MAINTENANCE (I/M) TEST Additional information concerning motor vehicle safety may be obtained from Transport Canada’s Road Safety Information Centre at 1-800-333-0371 or online at www.tc.gc.ca/roadsafety (English speakers) or www.tc.gc.ca/securiteroutiere (French speakers). To notify NISSAN of any safety concerns please contact our Consumer Information Centre toll free at 1-800-387-0122.
EVENT DATA RECORDERS (EDR) This vehicle is equipped with an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.
MEMO 9-32 Technical and consumer information
10 Index A Air bag (See supplemental restraint system) . . . . . . . . . . . . . . . . . . . . .1-53 Air bag system Front (See supplemental front impact air bag system) . . . . . . . . . . . . . . .1-60 Air bag warning labels . . . . . . . . . . . . .1-68 Air bag warning light. . . . . . . . . . .1-68, 2-14 Air cleaner housing filter . . . . . . . . . . . .8-18 Air conditioner Air conditioner service . . . . . . . . . . .4-49 Air conditioner specification label . . . . .
Cleaning exterior and interior . . . . . . . . . . .7-2 C.M.V.S.S. certification label . . . . . . . . . .9-10 Cold weather driving . . . . . . . . . . . . . .5-33 Compact disc (CD) player . . . . . . . .4-74, 4-81 Console box . . . . . . . . . . . . . . . . . . .2-47 Continuously Variable Transmission (CVT). . .5-15 Continuously Variable Transmission (CVT) fluid . . . . . . . . . . . . . . . . . .8-11 Driving with Continuously Variable Transmission (CVT) . . . . . . . . . . . . .
Fuel octane rating . . . . . . . . . . . . . . .9-4 Fuel recommendation . . . . . . . . . . . . .9-3 Loose fuel cap warning. . . . . . . .2-26, 3-28 Fuses . . . . . . . . . . . . . . . . . . . . . . .8-21 Fusible links . . . . . . . . . . . . . . . . . . .8-21 G Garage door opener, HomeLink® Universal Transceiver . . . . . . . . . . . . . . . . . . . Gas cap . . . . . . . . . . . . . . . . . . . . Gauge Engine coolant temperature gauge . . . Fuel gauge . . . . . . . . . . . . . . . . . Odometer . . . . . .
Light Air bag warning light . . . . . . . . .1-68, 2-14 Brake light (See stop light) . . . . . . . . .8-26 Bulb check/instrument panel . . . . . . . .2-10 Bulb replacement . . . . . . . . . . . . . .8-26 Charge warning light . . . . . . . . . . . .2-11 Fog light switch . . . . . . . . . . . . . . .2-35 Headlight and turn signal switch . . . . . .2-31 Headlight control switch . . . . . . . . . .2-32 Headlights . . . . . . . . . . . . . . . . . .8-25 Interior light. . . . . . . . . . . . . . . . . .
Power steering system . . . . . . . . . . .5-27 Power windows . . . . . . . . . . . . . . .2-50 Rear power windows . . . . . . . . . . . .2-51 Power inverter switch . . . . . . . . . . . . . .2-40 Precautions Maintenance precautions . . . . . . . . . . .8-5 On-pavement and off-road driving precautions . . . . . . . . . . . . . . . . . .5-6 Precautions on child restraints. . . . . . . . .1-33, 1-40, 1-45, 1-50 Precautions on seat belt usage . . . . . . .1-24 Precautions on supplemental restraint system . . .
Precautions on supplemental restraint system . . . . . . . . . . . . . . . . . . . .1-53 Supplemental restraint system (Supplemental air bag system) . . . . . . . . .1-53 Switch Autolight switch . . . . . . . . . . . . . . .2-32 Automatic power window switch . . . . . .2-52 Fog light switch . . . . . . . . . . . . . . .2-35 Hazard warning flasher switch . . . . . . . .6-2 Headlight and turn signal switch . . . . . .2-31 Headlight control switch . . . . . . . . . .2-32 Power door lock switch . . . . . . . .
Low windshield-washer fluid warning light . . . . . . . . . . . . . . . . . . . . Passenger air bag and status light . . . Seat belt warning light. . . . . . . . . . Vehicle security system . . . . . . . . . Warning/indicator lights and audible reminders . . . . . . . . . . . . . . . . . Warning labels (for SRS) . . . . . . . . Warning lights . . . . . . . . . . . . . . . . Washer switch Rear window wiper and washer switches . . . . . . . . . . . . . . . . . Windshield wiper and washer switch .
GAS STATION INFORMATION RECOMMENDED FUEL: Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91). CAUTION ● Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage. ● Under no circumstances should a leaded gasoline be used, because this will damage the three-way catalyst. ● Do not use E-15 or E-85 fuel in your vehicle.
Printing : May 2013 (04) 0R52U0 Publication No.: OM14E OM1E 0R51U0 Printed in U.S.A.
