Installation guide

ManualsBrandsCar Show ManualsAutomotiveDual DVD Headrest Replacement System

Car Show Installation Guide CS005 Rev A

Page 1

INSTALLATION GUIDE

Car Show Dual DVD Headrest Replacement System

NOTICE OF INTENDED INSTALLATION AND USE E

CAR SHOW VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO

BE INSTALLED ONLY TO BE VIEWED BY REAR-SEAT OCCUPANTS.

IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH SAFE

OPERATION OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH, AND

COULD ALSO VIOLATE STATE LAW. CAR SHOW DISCLAIMS ANY LIABILITY FOR ANY BODILY

INJURY OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED

INSTALLATION AND/OR USE.

BEFORE YOU START THE INSTALLATION, READ THIS GUIDE!

Car Show “Headrest DVD” systems are the easiest-to-install DVD entertainment systems available today.

However, we strongly recommend reading this guide before starting the installation!

1 Make sure you have the tools you will need

These common items are needed to complete this installation:

· Digital multimeter (DMM) · #2 Phillips screwdriver

Appropriate tool for headrest removal

Allen wrench set

Panel removing tools

Cable routing tool (included)

Security latch tool (included)

Retractable knife

Wire cutters, strippers, and a crimping tool

1/4” drive sockets are often needed for dashboard and trim disassembly

Check if Torx or Allen-drive bolts are used on any panels you will be removing

You will need a DVD

in good condition

when testing the system

Standard installation parts you will need include wire, wire ties, wire crimp connectors or solder, and

electrical insulating tape. Installation of aftermarket automotive electronics also often requires access to

special parts. It is a good idea to have a source for these common installation parts.

2 Inspect the vehicle and plan your work k

CHECK THE BATTERY

Test the battery voltage to make sure it’s fully charged and inspect battery terminals for tightness and any

corrosion. This only takes seconds and can save hours of troubleshooting later.

Summary of content (9 pages)

PAGE 1
INSTALLATION GUIDE Car Show Dual DVD Headrest Replacement System NOTICE OF INTENDED INSTALLATION AND USE E CAR SHOW VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER, AND ARE TO BE INSTALLED ONLY TO BE VIEWED BY REAR-SEAT OCCUPANTS. IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH SAFE OPERATION OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH, AND COULD ALSO VIOLATE STATE LAW.
PAGE 2
DECIDE ON A LOCATION FOR THE INTERFACE UNIT Location of the interface unit varies by vehicle, but is typically secured underneath a driver or passenger seat out of sight and unobstructed by moving parts and passengers. IF YOU HAVE PURCHASED A PRE-ASSEMBLED HEADREST SYSTEM, SKIP TO SECTION 6 3 Installing the electronics mounting bracket You will need to install the electronics mounting bracket. The following steps will guide you through this process.
PAGE 3
5 Mounting the Car Show electronics into the headrest bucket You will need to mount the Car Show electronics unit into the headrest bucket. The following steps will guide you through this process. to the LCD CAUTION! Do NOT press directly on the surface of the LCD. This will cause permanent damage which will not be covered by warranty. Always REMOVE ANY SLACK in the cables during assembly. Failure to follow this step may cause damage to the cables.
PAGE 4
Wiring diagram Gray Black REMOTE AUX 2 FMM OUTPUT IR A A/V OUTPUT Gray MONITOR A IR B A/V OUTPUT Black MONITOR B POWER Interface Harness Red – 12V ACC (switched) Black – Ground Gray – 12V Switch-FMM Black – Ground-FMM Blue – 12V (Aux source) Black – Ground (Aux source) Purple – Antenna 6 Removing the factory headrests IMPORTANT! Do NOT start this step until you have inspected the seats and factory headrests for any obstructions. You will need to remove the existing factory headrests.
PAGE 5
7 Installing the Car Show headrests You will need to install the Car Show headrests and route the cables through the seat backs. The following steps will guide you through this process. Step 1: Check the headrest down tubes in the seat backs for any obstructions. Normally the down tubes are clear and allow the Car Show cables to exit from the bottom of the down tubes. Step 2: Position the Car Show headrest so the monitor will be facing the rear of the vehicle once properly installed.
PAGE 6
8 Routing the harnesses and making the wiring connections It is the installer’s responsibility to ensure that the safety equipment in the vehicle is NOT adversely affected by installation of this system. Ensure that the routing of the harnesses does NOT obstruct airbags, SRS or other safety devices. You will need to route the harnesses and make the power connections to the vehicle. The following steps will guide you through this process.
PAGE 7
Step 3: PRE-DELIVERY AND RE-TEST a. Start the vehicle (ensure that it is safe to do so, there are no tools or people under the hood) b. Perform the following steps • Insert a DVD (in good condition) and select play • Re-check IR headphones and FMT audio • Eject the disc • Remove the protective films and clean the unit as needed c. Place the Owners Information package in the glove compartment d.
PAGE 8
FAQ’s The monitor cables get stuck in the posts Normally the cables will slide through the posts with very little effort. However, if you encounter difficulty, please check the following: Solution: Ensure that there are no obstructions inside the post. Solution: Ensure that there are no metal burs at the entrance or exit of the posts. Solution: Ensure that there are no kinks or knots in the cables. Solution: Use a cable pulling lubricant.
PAGE 9
Selecting FMM pre-sets For best operation, the FMM Pre-set selection should be on a station which is not in use or has weak broadcast in your area. Solution: You can also check www.RosenDealerCentral.com. This site provides you with the best stations in your local area. Select a corresponding FMM Station when available. Reducing audio or video noise Audio or video noise may be induced into the system from sources ranging from harness location, power point to poor grounding.