ns tio Release date : 2011.07.19 Model : QVI-AUD09-V6 / Product code : AUD09-1107-001 So lu Video Interface for AUDI 2009-2011~ model years C ar With MMI 3G/3G+ head units With external touch screen panel support Installation Manual www.car-solutions.com support@carsolutions.com.
Contents 1. Before installation tio ns 1.1 Main specifications 1.2 Features 1.3 System diagram 1.4 Components 1.5 Exterior 3. Installation C ar So 2.1 DIP switches 2.2 Remote controller 2.3 Original buttons in car 2.4 OSD buttons activation 2.5 OSD Menu (On Screen Display) 2.6 FACTORY mode 2.7 Rear view camera parking guideline 2.8 Touch screen panel calibration 2.9 Remote controller buttons 2.10 DVD, DVB-T model selection lu 2. Setup 3.1 Installation diagram 3.2 Cautions on installation 3.
1.1 Main Specifications tio ns 1. Inputs (MULTI VIDEO INTERFACE) - 1 x Analog RGBCs (for navigation system) - 1 x REAR-C Input (for external rear camera source, supports NTSC & PAL auto detection) - 3 x A/V Input (for external video source - DVD, TV, DVB-T; supports NTSC & PAL auto detection) - 1 x SYS Input – To SYS (video input from MMI 3G unit) - 1 x Touch In – To Touch (for external touch screen panel) So lu 2.
1.2 Features ns DVD, DVB-T and Navigation unit control via external touch screen panel tio DVD, DVB-T, navigation control via OEM MMI 3G buttons Installation near MMI 3G unit lu Plug & Play installation (LVDS cable offered) So Possibility to adjust position of AV1-3, RGB image Screen display adjustment (user friendly interface) C ar Remote control unit Mode change via OEM MODE switch on the wheel (only when connected to CAN bus) Control of rear view camera power www.
1.3 System Diagram ns TOUCH CONTROLLER lu NAVIGATION LCD INPUT\OUTPUT SUB BOARD VIDEO CIRCUIT C ar REAR-C (external rear camera input) OEM LCD Video Interface A/V1 Input A/V3 Input LVDS So RGB input for Navigation unit A/V2 Input MCU MMI 3G UNIT tio DVD IR DVB-T IR MODE Button DIP Switches Remote control POWER CIRCUIT External Touch Panel VIDEO MUX Headrest Monitors Power Input (+10 V DC~+16 V DC) www.car-solutions.
LVDS cable * 1pc. lu So Cable with remote mode switch button * 1pc. TOUCH IN cable * 1pc. C ar RGB cable * 1pc. OEM cable * 1pc. tio TOUCH OUT cable * 1pc. IR cable * 1pc. ns 1.4 Components POWER cable (24P) * 1pc. www.car-solutions.com Rear camera power cable * 1pc. AV cable * 1pc. Remote control * 1pc.
1.5 Exterior SUB BOARD ⑥ (47*38*22) ⑤ Dimension ⑩ Horizontal length 146 mm Vertical length 88 mm Height 25 mm ⑤ tio ⑥ ⑪ lu ⑦ ns ⑦ ① LED So ② POWER/CAN/RGB ③ REAR CAMERA POWER ① ② C ar ④ AV (IN/OUT) ③ ④ ⑤ LVDS OUT ⑥ TOUCH OUT TO NAVI ⑦ DIP S/W ⑧ ⑨ ⑧ TO VIDEO INTERFACE ⑨ TO TOUCH SCREEN PANEL ⑩ TO OEM DISPLAY ① ② ③ www.car-solutions.
2.1 DIP Switches RGB Input ON : RGB Input is OFF OFF : RGB Input is ON 2 A/V1 Input ON : A/V1 Input is OFF OFF : A/V1 Input is ON 3 A/V2 Input ON : A/V2 Input is OFF OFF : A/V2 Input is ON A/V3 Input 5 OEM Display Size 7 8 - Inputs to be used: A/V3(DVD), CS9100 navigation box (RGB) - External rear view camera: connected to REARC input ON : 7” LCD with 800*480 Resolution OFF : 6.5” LCD with 400*240 Resolution NOT USED C ar 6 ON : A/V3 Input is OFF OFF : A/V3 Input is ON [AUDI 2009 LCD 6.
Function POWER & PIP NOT USED lu OK OSD Menu Selection or Mode change Move UP So MENU tio Buttons ns 2.2 Remote Controller C ar Move DOWN Move LEFT (or press 2 sec. – Factory Mode) Move RIGHT (or press 2 sec. - Factory Reset) www.car-solutions.
2.3 Original Buttons on MMI Panel or On Wheel ① ③ ⑩ ⑨ ns ⑧ ④ ⑥ NAVIGATION control Temporarily NOT USED DVD, DVB-T control MODE CHANGE ⑤ Confirm ⑨ Move counterclockwise ⑩ Move clockwise If there is the MODE handle button on the steering wheel and interface is connected to CAN bus, driver can change modes by the MODE button. C ar ① Move UP ② Move Down ③ Magnification ④ Reduction ⑤ Confirm; press 2 sec. - Menu ⑥ Return - press 2 sec. ⑦ Setup for destination. If pressed 2 sec.
2.4 OSD Buttons Activation OSD Buttons for DVD ns For DVD control via OSD menu installer shall connect DVD system to AV1 input and join “DVD IR” cable from video interface cables with DVD IR receiver DATA cable. tio First of all, if you touch the screen in mode ”AV1”, you can see the menu as shown left. And then if you do NOT touch anything on the screen for 5 seconds or longer; or if you touch the screen in the place beyond menu, the menu will disappear.
2.5 OSD Menu (On Screen Display) OSD menu: Press ”MENU” button on the remote controller. Analog RGB mode Video AV1-3 mode Video AV1-3 mode Analog RGB mode Video AV1-3 mode IMAGE C ar So lu tio ns Analog RGB mode - BRIGHTNESS - CONTRAST - SATURATION - HUE - SHARPNESS - USER IMAGE: To choose among 4 prepared color shades. www.car-solutions.
2.6 Factory Mode Factory mode: press ◀ button for 2 sec.
2.7 Rear View Parking Guideline Factory mode: press ◀ button 2 sec. tio ns ① Set “ON” in “PARK ENABLE” line in the PARK section as shown left. (default – ON) . In case camera you want to connect already has parking lines, you should turn this function off in order to avoid parking lines and rear view camera image overlapping. To do this set “OFF”. C ar So lu ② If you turn rear gear after setup, parking guidelines will appear on screen as shown left.
2.8 Touch calibration tio ns If you use external touch screen panel for connected DVD player, TV tuner, DVB-T receiver control by OSD buttons, which will emulate remote controller buttons of these devices, you should calibrate the connected touch screen panel. C ar So lu >>> ① First of all, press ◀ button on remote controller for 2 seconds. Then you can enter the FACTORY mode. ② Set “YES” after CALIBRATION option is selected as shown above. www.car-solutions.
2.9.1 Remote Controller Button tio ns Programming OSD buttons value using remote controller supplied together with DVD,TV,DVB-T. If you want to control DVD and DMB models other than SANYO and NECVOX via touch screen (using OSD menu, you can program value of DVD and DMB’ s remote controller which you have. Then you can control DVD and DMB via touch screen. So lu >>> C ar ① First of all, press ◀ button on remote controller for 2 seconds. Enter FACTORY mode, then select IR MEMORY in UTIL section.
So lu tio >>> ns 2.9.2 Remote Controller Button C ar Programming Instructions> continued… c. Programmed values will appear as green text in the marked area on pressing the button. And the values will be saved automatically. d. Program other buttons value in OSD menu according to the above-mentioned procedure. www.car-solutions.com ③ After programming select “INPUT” in OSD menu and press “OK”. Then you can see confirmation window as shown above. If you choose “YES”, all entered values will be saved.
2.10 DVD, CMMB Model Selection Factory Default : DVD TYPE – NECVOX/SANYO CMMB TYPE – PIONEER/PANASONIC So lu tio ns CMMB TYPE C ar DVD TYPE UTIL – DVD/DMB TYPE If DVD/CMMB type that you want to use is not NECVOX or SANYO, you have to register values of the remote controller that you want to use in the “IR MEMORY” section and set the “DVD TYPE”/”CMMB TYPE” to “USER”. If you do not perform this process after saving the data, you WILL NOT be able to control DVD/CMMB via touch screen.
3.1 Installation Diagram Touch panel not included! NOT INCLUDED! USB Touch Screen Controller Touch cable X+ Y+ XY- DIP S/W Offered LCD cable LVDS OUT lu TOUCH OUT TO NAVI TO SYS SUB BOARD TO I/F TO TOUCH A/V(IN/OUT) LVDS cable Offered Touch In cable Audio R Audio L Video www.car-solutions.
3.2 Cautions on Installation Ignition key should be taken off before starting installation, interface power connection must be the last step in installation. Power cable should be disconnected during interface installation. There should be no electronic devices or magnetic pole around the installation place. All steps of installation should be done by well-trained specialist.
lu So Rear view of monitor tio ns 3.3 Installation C ar Rear view of MMI 3G unit ① The pictures show rear view of the disassembled monitor and MMI 3G unit. You can see that original monitor LCD cable is connected to the MMI 3G unit. www.car-solutions.com ② Disconnect original LCD cable from MMI 3G unit and connect it to “TO MONITOR” socket of the sub-board. Then connect the LCD cable included in video interface package to “TO SYS” socket of the sub-board.
ns 3.3 Installation So lu tio Navigation unit C ar ② Connect the TOUCH OUT cable enclosed in our package to “TOUCH OUT TO NAVI” socket of the video interface. Then connect its opposite end to the navigation system touch cable or USB Touch Screen Controller connected to navigation unit. (USB touch screen controller is not included in the package.) ① Connect the TOUCH IN cable to external touch screen flat cable. Then connect its opposite end to “TO TOUCH” socket of the sub-board. www.car-solutions.
3.4 Using Original Navigation Button C ar So lu tio ns If you want to use OEM NAVI button for changing modes, you need to connect to 16 pin connector wiring. - Case of A8 - Find cables bundle connected to OEM DVD device (in glove box or under OEM monitor) and connect orange wire from POWER cable with white wire of OEM DVD device. (NOTE: manufacturer can change wiring colours!!!). If you have Audi A8, connect white/blue wire to orange wire of power cable as shown on the left picture.
3.5 CAN Cable Connection C ar So lu tio ns If you connect the CAN cable in models with ”MODE” handle button, you can change modes via “MODE” button. Connection to CAN COMFORT bus shall be performed according to car schematics in each separate case to avoid car modular units damage. Above you can see example of connection to CAN COMFORT bus in Audi Q7 of 2010 model year. Connection was performed to red 20 pin connector (connector was disconnected from the air conditioner control panel).
4. Troubleshooting ns Q. I can not switch A/V sources. A. Check IR or Ground cable, and MODE button connection. Check LED lamps in the interface, if they are not on, check power cable. tio Q. All I got on the screen is black. A. Check whether interface green LED lamp is on. If not, check whether connected A/V sources operate well. (Green lamp indicates that connected AV sources are working well.) Check interface connection. So lu Q. Displayed image color is not proper.
