m io ns . co Release date : 2012.10.08 model : QVI-LVTX-1CH-V7 / product code : LVTX-1CH-1201-005 C ar -S ol ut Car Video Interface for Dodge/Chrysler www.car-solutions.com User Manual support@car-solutions.
m Contents 1. Before installation io ns . co 1.1 Main specification 1.2 Features 1.3 System diagram 1.4 Components 1.5 Exterior 2.1 DIP switch 2.2 Remote controller 2.3 Original buttons in car 2.4 OSD (on screen display) 2.5 FACTORY mode 2.6 Rear view parking guide line 2.7 Remote controller button 2.8 DVD, DTV model selection -S 3. Installation 8 9 10 11 12 13 14 16 ol ut 2. SETUP 3 4 5 6 7 17 18 19 ar 3.1 Installation diagram 3.2 Cautions on installation 3.3 Installation 4.
co io ns . 1. Input Spec. (MULTI VIDEO INTERFACE) - 1 x Analog R, G, B, C sync - 1 x CVBS(REAR CAMERA) Input. (Rear camera source) - 3 x A/V (NTST & PAL) Input. - 1 x LCD Input (Car system Input) m 1.1 Main specification ol ut 2. Output Spec. - 2 X CVBS OUTPUT (Video Out for installing Headrest monitor) - 1 x Audio OUTPUT - 1 X LCD OUTPUT(LCD Operation) 3. Power Spec. - Input Power : 8VDC ~ 18VDC - Consumption Power : 3WATT (in maximum level) C ar -S 4.
co m 1.2 Features DVD, DTV control via registering values of the buttons on the remote controller (only Plug & Play (the LVDS cable offered) io ns . for models including remote controller Control of position of the DVD, navigation image Compatible Cars C ar -S - Dodge Charger 2011~ - Fiat Freemont - Dodge Journey - Chrysler 300C ol ut Mode switch via original button www.car-solutions.com support@car-solutions.
m 1.3 System diagram Switch for source toggle co Remote Control RGB Input MCU A/V1 A/V2 VIDEO CIRCUIT LCD In/Out ol ut A/V3 CVBS (Rear Camera) VIDEO MUX POWER CIRCUIT A/V OUT -S DVD ar DMB OEM Button (Can Signal) io ns . RGB Touch Input DIP S/W NAVI C Power Input (+8VDC~+18VDC) HEADREST MONITOR www.car-solutions.com support@car-solutions.
LVDS cable * 1EA TOUCH IN cable* 1ea (HTOUCH0013) io ns . TOUCH OUT cable * 1ea (HTOUCH0004) IR cable * 1ea (HIRCAB0002) co m 1.4 Components (HLVDSC0014) ol ut MODE cable * 1ea (HARETC0001) -S RGB cable * 1ea (HNAVIC0004) www.car-solutions.
⑦ ⑧ Dimension co ⑥ m 1.5 Exterior ⑫ ⑬ io ns . Horizontal length 147mm Vertical length 91mm Height 27mm ① LED ol ut ② POWER/CAN/RGB ③ RGB IN-2 ⑨ ⑩ ⑪ ② ③ ④ ⑤ ⑤ AV(IN/OUT) ⑥ DIP SWITCH ⑦ TOUCH OUT TO NAVI ⑧ LVDS OUT ⑨ LVDS-IN ⑩ LED ⑪ LCD-OUT ⑫ TOUCH IN/OUT ⑬ LCD-IN C ① ar -S ④ REAR CAMERA www.car-solutions.com support@car-solutions.
DIP S/W selection 1 RGB INPUT skip ON : Skipping RGB Mode OFF : RGB Display A/V 1 skip 3 A/V 2 skip ON : Skipping A/V 2 OFF : A/V2 Display 4 A/V 3 skip ON : Skipping A/V 3 OFF : A/V3 Display N.C 6 N.C DIP S/W : 1 OFF DIP S/W : 2,3 ON (input mode skip) DIP S/W : 4 OFF (A/V3 available) DIP S/W : 7 ON (External Real Camera available) ON : External Rear Camera OFF : OEM Rear Camera ar 8 Rear Mode ▷ ▷ ▷ ▷ N.
Key Function Not for use OSD implementation io ns . POWER & PIP MENU co m 2.2 Remote controller Making a selection ▲ Move upward ▼ Move downward ◀ Move leftward, press 2 seconds long-Factory mode implementation ▶ Move rightward, press 2 seconds long-Factory Mode implementation-Factory mode Reset C ar -S ol ut OK www.car-solutions.com support@car-solutions.
m 2.3 Original buttons in car co ※ User can find this button from back of the steering wheel(Chrysler has buttons as same place) io ns . DTV channel up Mode Switching ol ut Driver can switch modes with the this button. -S Press long : mode switch Press short : return to main image C ar DTV channel down www.car-solutions.com support@car-solutions.
2.4 OSD (on screen display) Analog RGB Video Video Analog RGB ol ut io ns . co Analog RGB m OSD menu: Press ”MENU” button on the remote controller.
2.5 Factory mode m Factory mode: press ◀ button 2 seconds long. co IMAGE PARK io ns . - H-POSITION : Control over horizontal movement of screen - V-POSITION : Control over vertical movement of the screen - AVOUT SELECT : DEFAULT, AV1, AV2, AV3 -S ol ut - PARK ENABLE : Setup of rear view parking guide line - PARK SETUP : Control over position of rear view parking guide line (Refer to page13.
2.6 Rear view parking guide line m Factory mode: press ◀ button 2 seconds long. io ns . co ① Register the value needed on the “PARK ENABLE” as “ON” in the PARK section as shown left. (default – ON) -S ol ut ② If you get rear gear after setup, parking guide line will appear on screen as shown left. Now that you push “OK” button, you can see “H-POS” on the left of screen. Then adjust horizontal position of the guide line.
2.7.1 Remote controller button io ns . co m Registering value of remote controller buttons? When you want to control DVD and DTV via touch screen (using OSD menu) with other models besides already registered option-SANYO and NECVOX, you can register value of DVD and DTV’ s remote controller which you have. Then you can control DVD and DMB via touch screen. ol ut >>> ① First of all, press ◀ button on remote controller 2 seconds long. Then you can access to the FACTORY mode. And go to IR MEMORY, UTIL.
ol ut io ns . >>> co m 2.7.2 Remote controller button C ar -S Instruction> continued… c. The values that you registered will appear as green text in the marked area on pressing the button. And the values will be saved automatically. d. Register remain buttons’ value in OSD menu like the above-mentioned. www.car-solutions.com ③ After register, select “INPUT” in OSD menu and press “OK”. Then you can see confirmation window as shown above.
UTIL – DVD/DTV TYPE DTV TYPE -S DVD TYPE ol ut io ns . co m 2.8 DVD, DTV model selection ar If DVD/DTV type that you want to use is not NECVOX or SANYO, you have to register values of the remote controller that you want to use in the “IR MEMORY” section and set the “DVD TYPE”/”DTV TYPE” to “USER”. Unless you do this process after saving the data, you can NOT control DVD/DTV via touch screen.
m 3.1 Installation diagram LCD-OUT X+ Y+ XY- SUB BOARD Offered LCD cable DIP S/W TOUCH OUT TO NAVI AUX-ON (N.C) C ar IR www.car-solutions.com PB12 (N.
m 3.2 Cautions on installation Ignition key should be taken off before starting installation, interface power connection must be the last step in installation. Power cable should be separated when connecting interface. Should be no any electronic devices or magnetic pole around installation place. All steps of installation should be done by well-trained specialist. Dismantling without manufacturer’s permission can not be guaranteed, (No permission to break attached label on the board.
m 3.3 Installation ② ① Original LCD cable COMMNAD ol ut io ns . Offered LVDS cable co 1. Connect LVDS Cable Offered LCD cable -S ③ C ar 1. Offered LVDS Cable connect to LVDS-IN in Sub-board 2. After dividing original LCD cable from the back of monitor, and connect with LCD-IN in sub-board 3. Offered LCD cable connect with LCD-OUT in sub-board and the marked point from the back of monitor ※ The Power of Interface connect with accessory Power in the car www.car-solutions.
2. Connecting CAN cable respectively CAN-Low Power Cable CAN-High ar -S ol ut io ns . co The LCD cable in the back of monitor connect with offered powercable m 3.3 Installation C Connect CAN-H cable (green+brown) enclosed in our package with the original CAN-H cable (White+Blue). And connect CAN-L cable (green) enclosed in our package with the original CAN-L cable (White+Yellow). www.car-solutions.com support@car-solutions.
m 4. Troubleshooting co Q. I can not switch A/V sources. A. Check IR or Ground cable connection. Check LED lamps in the interface, if it is not on, check power cable. io ns . Q. All I got on the screen is black. A. Check second LED lamp of the interface is on, if not, check A/V sources connected are working well. (Second lamp indicates AV sources connected works well.) Check interface connection has been done well. Q. Displayed image color is not proper. (too dim or not suitable color) A.
