ns tio Model : QVL-A6LE-V3 / Product code : AD-1012-001 So lu Video Interface for AUDI A4, A5, A6, A8, ALLROAD, Q5, Q7 C ar With MMI 2G head units With external touch screen panel support Installation Manual www.car-solutions.com support@carsolutions.com.
Contents 1. Before installation tio ns 1.1 Main specifications 1.2 Features 1.3 System diagram 1.4 Components 1.5 Exterior 1.6 Power Cable 3. Installation C ar So 2.1 DIP switches 2.2 Remote controller 2.3 Original buttons 2.4 OSD buttons activation 2.5 OSD-menu (On Screen Display) 2.6 FACTORY mode 2.7 Rear view parking guideline 2.8 External touch screen panel calibration 2.9 Remote control buttons 2.10 DVD, DMB model selection lu 2. Setup 3.1 Installation diagram 3.2 Cautions on installation 3.
1.1 Main Specifications tio ns 1. Input Spec. (MULTI VIDEO INTERFACE) - 1 x Analog RGBCs (for navigation system) - 1 x REAR-C Input (for external rear camera source, supports NTSTC & PAL auto detection) - 3 x A/V Input (for external video source - DVD, TV, DVB-T; supports NTSC & PAL auto detection) - 1 x LCD-OUT (input for video from MMI 2G unit) - 1 x NAVI Touch (for external touch screen panel) So lu 2. Output Spec.
ns 1.2 Features DVD, DVB-T and Navigation unit control via external touch panel lu Installation near OEM display tio DVD, DVB-T, navigation control via OEM MMI buttons So Plug & Play (the LVDS cable offered) C ar Possibility to adjust position of AV1-3, RGB image Screen display adjustment (user friendly interface) Remote controller offered www.car-solutions.
1.3 System Diagram A/V1 Input A/V2 Input ns lu RGB input for Navigation unit MCU LCD INPUT\OUTPUT So NAVIGATION TOUCH SCREEN CONTROLLER tio DVD IR DVB-T IR MODE Button DIP Switches Remote controller MMI 2G UNIT Video Interface External Touch Screen Panel VIDEO CIRCUIT C ar A/V3 Input REAR-C (external reverse camera input) OEM LCD POWER CIRCUIT VIDEO MUX Headrest Monitors Power Input (+10 V DC~+16 V DC) www.car-solutions.
1.4 Components tio ns LCD-IN cable * 1pc. Remote Controller * 1pc. So lu TOUCH out cable * 1pc. IR cable * 1pc. Power cable (8P) * 1pc. C ar Navi touch cable * 1pc. Mode button * 1pc. www.car-solutions.com IR OUT cable * 1pc. RGB cable * 1pc. A/V cable * 1pc.
1.5 Exterior Dimensions ② ① tio ns Horizontal length 130mm Vertical length 105mm Height 20mm lu ③ So ④ ⑥ ⑦ www.car-solutions.
tio ns 1.6 Power Cable So C ar GND ring terminal (is connected to car body in the place of installation) Noise filter box lu Fuse box MMI OEM button - NAVI REAR view camera activation SAFE GND -12 В ACC (BAT) +12 В www.car-solutions.
2.
Function POWER & PIP NOT USED lu OK OSD Menu Selection or Mode change Move UP So MENU tio Buttons ns 2.2 Remote Controller C ar Move DOWN Move LEFT (or press 2 sec. – Factory Mode) Move RIGHT (or press 2 sec. - Factory Reset) www.car-solutions.
2.3 Original Buttons ① ③ ⑩ ⑨ tio ⑤ ④ ① Move up ② Move down ③ Magnification ④ Reduction ⑥ Return - press 2 sec. ⑦ Setup for destination or press C ar Temporarily NOT USED ⑥ So NAVIGATION implementation lu ② ⑦ ⑤ Confirm or press 2 sec.- menu ns ⑧ long 2sec. - driving in night mode ⑧ Mode change ⑨ Move left ⑩ Move right DVD, CMMB implementation ⑤ Confirm ⑨ Move counterclockwise ⑩ Move clockwise ※ If you press any of these three buttons, DVD/CMMB OSD menu will appear on the screen.
2.4 OSD Buttons Activation OSD buttons for DVD ns For DVD control via OSD menu installer shall connect DVD system to AV1 input and join “DVD IR” cable from video interface cables with DVD IR receiver DATA cable. tio First of all, if you touch the screen in mode ”AV1”, you can see the menu as shown left. And then if you do NOT touch anything on the screen for 5 seconds or longer; or if you touch the screen in the place beyond menu, the menu will disappear.
2.5 OSD-menu (On Screen Display) OSD menu: Press ”MENU” button on the remote controller. Analog RGB mode Video AV1-3 mode Video AV1-3 mode Analog RGB mode Video AV1-3 mode IMAGE C ar So lu tio ns Analog RGB mode - BRIGHTNESS - CONTRAST - SATURATION - HUE - SHARPNESS - USER IMAGE : To choose a option among 4 prepared color shades. www.car-solutions.
2.6 Factory Mode Factory mode: Press ◀ button 2 sec. or ▲ -> ▼ -> ▲ ->MENU buttons of the IR remote controller ns IMAGE So PARK lu tio - H-POSITION: horizontal movement of screen (image alignment) - V-POSITION : vertical movement of the screen (image alignment) C ar - PARK ENABLE: Rear view camera parking guidelines activation.
2.7 Rear View Parking Guideline Factory mode: Press ◀ button 2 sec. or ▲ -> ▼ -> ▲ ->MENU buttons of the IR remote controller tio ns ① Set “ON” in “PARK ENABLE” line in the PARK section as shown left. (default – ON) . C ar So lu ② If you turn on rear gear after setup, parking guidelines will appear on screen as shown left. Now if you push “OK” button, you can see “H-POS” on the left of screen. Then adjust horizontal position of the parking guidelines.
tio ns 2.8 External Touch Screen Panel Calibration C ar So lu >>> ① First of all, press ◀ button on remote controller for 2 seconds. Then you can enter the FACTORY mode. ② Set “YES” after CALIBRATION option is selected as shown above. www.car-solutions.com ③ After that “touch calibration” caption appears on screen for about 2 seconds as shown above. When it disappears you can calibrate the touch screen. (Just touch on screen.) If calibration was performed, “success” caption will appear.
2.9.1 Remote Controller Buttons Programming OSD buttons value using remote controller supplied together with DVD,TV,DVB-T. tio ns If you want to control DVD and DMB models other than SANYO and NECVOX via touch screen (using OSD menu, you can program value of DVD and DMB’ s remote controller which you have. Then you can control DVD and DMB via touch screen. So lu >>> C ar ① First of all, press ◀ button on remote controller for 2 seconds. Enter FACTORY mode, then select IR MEMORY in UTIL section.
2.9.2 Remote Control Buttons tio ns So lu >>> C ar ③ After programming select “INPUT” in OSD menu and press “OK”. Then you can see confirmation window as shown above. If you choose “YES”, all entered values will be saved. If you select “NO”, the values won’t be saved. If data is saved, DVD TYPE and DMB TYPE will be changed to “USER” automatically.) If you see “SUCCESS” caption on screen, the data is saved and you can control DVD via touch screen.
2.10 DVD, DMB Model Selection C ar So lu tio ns Factory Default : DVD TYPE – NECVOX/SANYO DMB TYPE – DVB-T(CMMB) PIONEER\PANASONIC UTIL – DVD/DMB TYPE If DVD/CMMB type that you want to use is not NECVOX or SANYO, you have to register values of the remote controller that you want to use in the “IR MEMORY” section and set the “DVD TYPE”/”CMMB TYPE” to “USER”. If you do not perform this process after saving the data, you WILL NOT be able to control DVD/CMMB via touch screen.
3.1 Installation Diagram Offered LCD-OUT cable ns NOT INCLUDED! NAVI Touch cable CS9100 Navigation Unit TOUCH OUT VIDEO INTERFACE (A6LE) So NAVI TOUCH X+ Y+ XY- RGB (IN) A/V (IN/OUT) POWER NOT USED NOT USED NOT USED MMI BUTTON REAR CAM. SAFE GND -12V ACC (BAT) +12V C ar IR OUT Audio R Audio L Video www.car-solutions.
3.2 Cautions on Installation Ignition key should be taken off before starting installation, interface power connection must be the last step in installation. Power cable should be disconnected during interface installation. There should be no electronic devices or magnetic pole around the installation place. All steps of installation should be done by well-trained specialist.
lu tio ns 3.3 Installation 2. Connect NAVI TOUCH cable to navigation unit or to USB Touch controller (USB controller not included) C ar So 1. Connect LCD cable (included in the package) to OEM display and video interface. 4. You will find more detailed touch screen panel installation guide on the product page of any touch screen panel at www.car-solutions.com 3. Connect Touch Out cable to touch screen panel (touch screen panel is not included in the package) www.car-solutions.
3.4 Using Original NAVI button ※ If you want to use OEM NAVI button for changing modes, you need to connect to 16 pin connector wiring. lu tio ns ① Attention!!! Find A, B connectors of MMI module. For safety purpose, unplug MMI power cable (B connector) and then disconnect A connector. C ar So ② Find 16th pin after B connector unplugging . www.car-solutions.com ③ Connect Navi orange wire from Power cable to the 16th pin of the connector.
4. Troubleshooting ns Q. I can not switch A/V sources. A. Check IR or Ground cable, and MODE button connection. Check LED lamps in the interface, if they are not on, check power cable. tio Q. All I got on the screen is black. A. Check whether interface second LED lamp is on. If not, check whether connected A/V sources operate well. (Second lamp indicates that connected AV sources are working well.) Check interface connection. So Q. Rear camera image does NOT appear. A.