S1000-DAB In-Car Digital Radio Adaptor User Guide
S1000-DAB User Guide Table of Content INTRODUCTION.................................................................................................................. 1 CONTENTS OF PACKAGE.................................................................................................. 2 INSTALLATION .................................................................................................................... 3 OVERVIEW OF CONTROLS AND CONNECTORS.........................................................
S1000-DAB User Guide INTRODUCTION The S1000-DAB is an in-car audio adaptor that offers a flexible and cost effective way to apply modern digital audio technology to your existing analogue in-car audio system. The existing analogue system can be easily upgraded to receive DAB digital radio services without replacement of any component of the car audio system. In addition, the S1000-DAB can receive audio output from an audio device such as MP3 or iPod® etc.
S1000-DAB User Guide CONTENTS OF PACKAGE 1. S1000-DAB unit 2. Power Cable with Cigarette Lighter Plug 3. Audio Cable: Aux-in/out 4. Cradle (Stand, Holder) 5. Plain Plate 6. External Antenna with cable 7.
S1000-DAB User Guide INSTALLATION 1. Assemble the cradle Assemble the cradle by hooking up the stand into the holder 2. Secure the S1000-DAB unit into the cradle Place the S1000-DAB unit on the holder Line up the cradle’s tab to S1000-DAB, then pull the tab in until you hear it clicks in to the holder 3. Mount the cradle.
S1000-DAB User Guide Note: If you want to remove the S1000-DAB unit from the cradle, please do not just force pulling the tab. Hold the unit as shown below with one hand and the bottom finger push up the edge of the holder, and then push back (not down) with the other hand to release the unit from the cradle.
S1000-DAB User Guide OVERVIEW OF CONTROLS AND CONNECTORS Front Panel Side Panel 5
S1000-DAB User Guide Screen Display Two rows by 16 characters LCD display screen for system status and information.
S1000-DAB User Guide STARTING UP THE SYSTEM 1. 2. 3. 4. 5. Turn on the S1000-DAB car adaptor. S1000-DAB will perform a Full Scan of DAB stations automatically. Press FM on the S1000-DAB and the screen will show the current FM transmitting frequency, make a note of that number. The default is 87.6MHz. Turn on your in-car audio system. Switch the car radio’s FM frequency to match to S1000-DAB FM transmitting frequency setting. 6.
S1000-DAB User Guide USING DIGITAL RADIO ADAPTOR To Listen to the DAB Stations To select and listen to a DAB station, steps through the stations on the station list one by one and in alphabetical order. Press ◄ or ► to select the desired DAB station, the screen will show 《 Station List ; station name 》if the station is available or《 Station List ; ?station name 》if the station is not available. Press INFO/ENTER to start tuning the station selected. The screen will show 《 station name ; Tuning … 》.
S1000-DAB User Guide To Set DAB Presets The S1000-DAB provides individual memory settings for up to three sets of DAB Preset: DAB1, DAB2, DAB3. Each DAB Preset has its own Memory Presets of DAB stations (please refer to To Save a Memory Preset). This allows user to setup the three DAB Presets for different persons (driver or passenger) or different group of stations to enjoy the favorite programs based on the individual settings. Press MODE to select a particular DAB Preset.
S1000-DAB User Guide To Recall a Memory Preset This function allows you to recall a preset favorite DAB station from the Memory Preset List. Press the number key X that the desired DAB station is stored under. Keep pressing the number key X until the desired DAB station is displayed. Press INFO/ENTER to recall the station. Note: If there is no DAB station preset in Memory Preset location XY, the screen will show《 Preset Recall; XY: (Empty) 》.
S1000-DAB User Guide USING THE MENU CONTROL To Scan the DAB Stations This function scans the desired DAB band and searches for all DAB stations available in the area where your car is presently located. Stations found as a result of the search are added to the station list. There are three Scan types available in the S1000-DAB: Quick, Full, and Manual tune. When a Quick scan is performed, the S1000-DAB will scan only the part of Band III (from channel 9A to channel 13F).
S1000-DAB User Guide If the DAB Station List is empty before scanning, and there is no station detected by DAB Scan, the screen will show 《 DAB; Quick Scan 》. There are no DAB stations available in the area where you performed DAB Scan function. c. 2.
S1000-DAB User Guide radio is activated, your car radio will tune to an unused FM frequency automatically when you drive into an area where the original FM frequency for DAB is no longer available. You do not need to do To Enable AutoScan or To Set the FM Transmitting Frequency Setting in the sections below, to switch to an unused FM transmitting frequency.
S1000-DAB User Guide had found it. To see the new FM transmission frequency on screen after this time press the FM button. While in AutoTune mode, if the FM transmitting frequency for S1000-DAB and the Car Radio listening Frequency is out of sync, do the following in sequence to re-sync: Operating on Car Radio Press the FM preset of your car radio to the frequency 87.6MHz if you have previously saved for DAB reception. Otherwise, tune the car radio to FM frequency 87.6MHz manually.
S1000-DAB User Guide To Enable AutoScan If your car radio is not RDS compatible or does not have AF feature, you must not enable AutoTune. However, you can use AutoScan to automatically search for unused FM frequency for transmitting. When this function is activated, the S1000-DAB will keep searching available FM frequencies, and display these frequencies whenever you need.
S1000-DAB User Guide Frequency》where Frequency is the new frequency. Then the FM transmitter will transmit FM signal at the new frequency. Now you can listen to DAB stations via this FM frequency. Operating on Car Radio Manually change your car radio’s FM frequency to match the new S1000-DAB transmitting frequency setup.
S1000-DAB User Guide To Save a Desired FM Transmitting Frequency in Memory As unused FM frequency may vary from one area to another, it is suggested to save a few frequencies (up to 4 frequencies) in S1000-DAB so that you can switch to a new FM transmitting frequency instantly when you drive into an area where the original FM frequency for DAB is no longer available. Press MENU and then ◄ or ► until the screen shows《 System Setup 》.
S1000-DAB User Guide transmit FM signal at the new frequency. Now you can listen to DAB stations via this FM Frequency. To Set the FM Transmitting Power Level While listening to the DAB program, if you experience interference and noise, you may adjust the FM Transmitting Power Level to increase the power of FM signal transmission to suppress the interference. Press MENU and then ◄ or ► until the screen shows《 System Setup 》.
S1000-DAB User Guide To Enable Auto Dimming Press MENU and then press ◄ or ► until the screen shows《 System Setup 》. Press INFO/ENTER, and then press ◄ or ► until the screen shows 《 Auto Dimming 》. Press INFO/ENTER If you do want to disable, press ◄ or ► to find the 《 Off 》and press INFO/ENTER to disable the Auto Dimming. Otherwise, you can press INFO/ENTER to enable the Auto Dimming while the screen is showing 《 On 》 Note: The default is “On” and the Auto Dimming is enabled.
S1000-DAB User Guide press INFO/ENTER to cancel while the screen is showing 《 Factory Reset? ; Yes 》. 1. The screen will show《 Restarting… 》to indicate that factory reset is in progress. 2. The system will perform a Full scan of DAB stations automatically after the factory reset is completed. You must switch the car radio to FM 87.6MHz to continue DAB listening Note: Factory reset will erase all previous system’s settings and set them to default.
S1000-DAB User Guide TROUBLESHOOTING Please read this user manual carefully before using the S1000-DAB In-Car Digital Radio Adaptor. If you still have difficulties to use this unit, this section gives some of the most likely solutions to the problems you might have.. The LCD of S1000-DAB does not light up. Ensure that the power is properly connected; please refer to the installation page. If the S1000-DAB is powered by the cigarette lighter, ensure that the cigarette lighter is in order.
S1000-DAB User Guide is not available as you may have left the signal coverage area, please refer to the section To Listen to the DAB stations to select another station. Also, the station may be unavailable temporarily as you drive into a tunnel, While listening to a DAB station, I lost reception suddenly and hear static noise or a FM program but S1000-DAB shows station is available While in AutoTune mode, the FM transmitting frequency for S1000-DAB and the Car Radio listening Frequency maybe out of sync.
S1000-DAB User Guide TECHNICAL SPECIFICATIONS Digital Audio Services: DAB/DAB+. RF Frequency Range: DAB Band III (174 MHz ~ 240 MHz). RF Sensitivity for DAB Band III: -98dBm ~ -100dBm. FM Transmit Range: 87.6 MHz ~ 107.9 MHz. Mains Power: Input: 12-24V,Output: DC 5V,1A mini USB power adaptor. Input Connectors: 5V mini USB DC power connector, 3.5mm line in. Output Connectors: 3.5mm stereo output for headphones or connecting to car stereo aux-in (if available).
S1000-DAB User Guide INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL & ELECTRONIC EQUIPMENT This mark on a product and/or accompanying documents indicates that when it is to be disposed of, it must be treated as Waste Electrical & Electronic Equipment (WEEE). Any WEEE marked waste products must not be mixed with general household waste, but kept separate for the treatment, recovery and recycling of the materials used.
S1000-DAB V1.
