Specifications

N1430
N1714
716311
GM
Ford
12
clutch release arms & bearings
CLUTCH RELEASE ARMS & BEARINGS:
On the Clutch Selection Chart, the Centerforce clutches we have listed are all high diaphragm pressure plates. By using these
pressure plates, we can standardize on just a few release arms and bearings.
RELEASE ARMS: The clutch throw-out levers are available in several sizes, materials, and configurations. They can be purchased
at your local dealer or from us directly. The clutch release arms are not interchangeable between different manufacturers. For
example, you cannot use a Ford or AMC arm in a Chevy bellhousing. Most arms are held inside the bellhousing by a ball pivot that
the release arm clips over. The ball pivot permits the arm to swing back and forth to release the clutch.
In order to get the maximum efficiency from the clutch mechanism, the release arm portion that is outside of the bellhousing should
be angled approximately 3 to 5 degrees towards the engine block. The angle can be adjusted by using an adjustable ball pivot on
the bellhousing. (Adjustable ball pivots for GM bellhousings can be purchased at any auto parts store). With the clutch release lever
properly installed, you must maintain a minimum of .060" clearance between the release bearing and clutch fingers. It is important
that you verify the clearance between the clutch release arm and clutch pressure plate. There are some applications that will require
additional clearance for the clutch release arm.
The GM arm we use is the straight cast iron style, P/N 716176 (GM# 3765372), that accepts the groove-type throw out bearing.
On most of our conversion bellhousings and adapter plates, we recommend this arm (except on P/N 712548 bellhousing assembly).
The clutch linkage rod or slave cylinder rod that couples to the GM arm may require a pivoting wedge to prevent the linkage from binding.
We offer this wedge under P/N 716139 (GM# 3765322).
On Ford bellhousing applications, we have found a wide variety of release arms. The release arm that your stock Ford bellhousing
has is your best choice. The release arm normally accepts one of two types of release bearings: Up to 1981, Ford used a clip-
type. On 1982 & newer, Ford (like GM) uses a groove-type.
Jeeps are similar to the early Fords in that they use a clip-type release bearing. The
only application that we retain the stock Jeep throw out arm is with our conversion
bellhousing P/N 712548 (vehicles 1976-86). When using this bellhousing on vehicles
that were originally equipped with a AMC 4 cylinder, you will need to purchase:
Part No. 716332 (boot), 716333 (spring) & 716334 (T/O arm - Jeep# 5361620).
CLUTCH RELEASE BEARINGS: This bearing fits on the inside of your bellhousing and attaches to the release lever, providing
a means of disengaging the clutch while shifting the transmission. The bearing only rotates upon the depression of the clutch arm.
Depending on the height of the pressure plate, there are different lengths of bearings. It is important that you have the proper bearing
to obtain the proper release. There should be approximately .060" minimum clearance between the bearing and the clutch fingers.
The clutch pedal should have approximately 1" of play at the top of the pedal swing. If the bearing is allowed contact with the clutch
fingers prior to clutch disengagement, premature bearing failure will occur. The bearing must slip easily over the transmission
bearing retainer. The inside of the release bearing will have a small cavity that has been provided for grease storage. This cavity
should be packed with a good quality grease so that proper lubrication can be maintained between the bearing and transmission
bearing retainer. Most new bearings are already pre-lubricated.
The Centerforce clutches that we recommend are all high diaphragm pressure plates. They all require a flat-face release bearing.
If you are acquiring your own pressure plate, which may be a low diaphragm pressure plate, you will need a radius-face release
bearing.
When selecting the release bearing and using one of the Centerforce clutches recommended, there are two simple things to
consider. First, how does the bearing attach to the release arm? (Clip or Groove). Second, what is the external dimension of the
transmission snout that the bearing rides on? (The GM retainer snout is 1.37”, and Ford, Jeep & Dodge NV4500 is 1.43”).
P/N N1430 - 1.37” I.D. groove-type release bearing. This flat-face Chevy release bearing is used with high diaphragm
clutches. The inside diameter will fit Chevy transmission bearing collars.
P/N 716311 - 1.43” I.D. clip-type release bearing. This is a flat-face release bearing that will fit the Jeep transmission bearing
collars 1976-86. The bearing will clip onto the original Jeep release arm and can only be used with high
diaphragm type clutches. This bearing is also used on all Ford V8 conversions using the stock Ford release
lever on bellhousings 1981 & earlier. Ford and Jeep both have the same inside diameter on the bearing collar.
*P/N N1714 - 1.43” I.D. groove-type release bearing. This release bearing is a Ford style that requires a Ford release arm
having the groove-type connection. It should only be used when the late model Ford V8 release arms are being
used. This bearing also works well on Dodge NV4500 transmissions in
combination with the GM release arm. Slight modifications will be neces-
sary on the GM release arm to properly fit this bearing.
*(When using this bearing with a GM arm, the GM arm will require slight modifications)