™ Q2 pro ™ communication in motion ™ Gebrauchsanleitung Guide d’Utilisation Guida di Avvio Guia de Usario User Guide QGQ2PRO_ NB 009_001 - QG0179.
© Cardo Systems, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Cardo Systems, Inc. is under license. Other trademarks and trade names are those of their respective owners. 2 scala rider® Q2™ pro QGQ2PRO_ NB 009_001 - QG0179.
Congratulations, and thank you for choosing the scala rider Q2 pro Bluetooth® Headset for bikers. This Manual will help you operate the headset, but you should first familiarize yourself with the Bluetooth functionality of your cellular phone and/or GPS device before using the scala rider Q2 pro. CONTENTS OF RETAIL BOX Volume Up / Forward Headset Charging Jack The retail box of the scala rider Q2 pro contains one headset unit.
SET UP AND CONFIGURATION Wall Charger Allen Wrench Velcro Pads MP3 Cable Mobile phone MP3 Cable Holder Glue Plate Pre-moistened Towelette Carry-Pouch Microphone Sponges Flat sponge for full-face helmets and round sponge for other helmet types User Guide, including Warranty and Registration form Built-in FM radio Driver-to-Passenger Full-duplex Intercom Connection scala rider Q2 pro or other scala rider headset GPS MP3 player Bike-to-Bike Intercom up to 500 m / 540 yd (in open terrain) IMPORTANT: The
1. If either headset is turned OFF, turn it ON by pressing and holding the CTRL Button until the Blue Light flashes three times. 2. Make sure that both headsets are now flashing slowly in Blue. 3. Pick up one headset and simultaneously press and hold the CTRL Button and MC Button for at least six seconds until the Red Light begins flashing rapidly, indicating it is in Intercom Pairing mode. 4. Repeat Step 3 again for the second scala rider Q2 pro headset. Both headsets should now be flashing rapidly in Red.
1. Place the scala rider Q2 pro into Intercom Pairing mode following the instructions in the PRIMARY BUDDY PAIRING section above. 2. Once the Red Light begins flashing rapidly, press and hold Volume up for three seconds. 3. The Red and Blue Lights will flash five times, confirming that the Reset Pairing was successful.
GETTING STARTED ATTACHING THE CLAMP ON THE HELMET The Helmet Clamp must be attached to the left side of the helmet. Once attached, the headset unit can be mounted or released from the Helmet Clamp at any time. If you wish to connect your MP3 player to your headset, please refer first to the assembly instructions listed in section: USING THE MP3 PLAYER WITH YOUR HEADSET. There are two methods that can be used in order to attach the Clamp onto the helmet: Standard Method: Recommended for most helmet types.
4. Use the pre-moistened Towelette to clean the helmet area where you want to install the Glue Plate. Allow to dry thoroughly. 5. Peel the foil cover from the Glue Plates’ adhesive pad. 6. Place the Glue Plate into position according to #3. Press firmly 15 seconds on all 3 parts of the Glue Plate. 7. The adhesive pad bonds to full strength over the next 24 hours. Therefore it is recommended to not use the headset during this 24 hour period. 8.
Press here to remove USING THE HEADSET GENERAL USAGE GENERAL FUNCTIONS DESIRED RESULT: Turn on the headset Turn off the headset Increase the volume Decrease the volume REQUIRED ACTION: Press the CTRL Button steadily for at least three seconds Press the CTRL Button steadily for at least three seconds Tap the Volume Up Button Tap the Volume Down Button AGC (Automatic Gain Control): In addition to manual Volume Control, the scala rider Q2 pro will automatically increase and reduce its volume according to am
Reconnecting the Intercom: If the scala rider Q2 pro and its Intercom Buddy headset go out of range and disconnect from each other, the scala rider Q2 pro will automatically try to reconnect to its Intercom Buddy for five minutes. You can manually reconnect at any time by pressing the MC Button (single tap for Primary Buddy and double tap for Secondary Buddy).
STATUS LIGHT STATES None Headset is off Alternating Red/blue flashes Mobile phone/GPS Pairing mode Rapid Red flashes Intercom Pairing mode 1 blue flash every 3 seconds Standby – No call is in progress 2 blue flashes every 3 seconds Call being initiated or in progress / FM Radio ON / MP3 player on 1 red flash every 3 seconds Standby – Battery is low 2 red flashes every 3 seconds Battery is low while call is in progress/ MP3 player is ON / FM Radio ON Solid red Headset is being charged WORKING W
You may still continue to listen to the current unsaved station. Pressing the MC Button in this case will switch to the next saved station. Saving an FM Radio Station The FM Radio is equipped with a memory capacity of six stations. • Select the station you wish to replace by tapping the MC button until you find the station you want to replace. • Search for a new station as described above. • Tap the MC Button within 20 seconds of finding the station to save the current station.
Your scala rider Q2 pro headset can be connected to an MP3 player device by plugging it to the Helmet Clamp’s jack with the MP3 cable. At your option, you may further secure the MP3 cable by using the MP3 cable holder. For this purpose please proceed as follows: 1. Use the enclosed Allen Wrench to remove both Allen screws from Helmet clamp and release the clamp’s back plate. 2. Place the MP3 cable holder on the MP3 cable holder hook helmet clamp.
• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device.
Cardo hereby notifies you that using this Device may also be in contravention to local, federal, state or national laws or regulations, and that any use of the Device is entirely at your sole risk and responsibility. 1.
scala rider® Q2™ pro QGQ2PRO_ NB 009_001 - QG0179.