™ Q2 pro ™ communication in motion ™ User Guide
© Cardo Systems, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Cardo Systems, Inc. is under license. Other trademarks and trade names are those of their respective owners.
Congratulations, and thank you for choosing the scala rider Q2 pro Bluetooth® Headset. This Manual will help you operate the headset, but you should first familiarize yourself with the Bluetooth® functionality of your cellular phone and/or GPS device before using the scala rider Q2 pro. CONTENTS OF RETAIL BOX Volume Up / Forward MP3 Music Headset Charging Jack The retail box of the scala rider Q2 pro contains one headset unit.
SET UP AND CONFIGURATION Wall Charger Allen Wrench Velcro Pads MP3 Cable Mobile phone & A2DP connectivity MP3 Cable Holder Glue Plate Pre-moistened Towelette Carry-Pouch Microphone Sponges Flat sponge for full-face helmets and round sponge for other helmet types User Guide, including Warranty and Registration form Built-in FM radio Driver-to-Passenger Full-duplex Intercom Connection scala rider Q2 pro or other scala rider headset GPS MP3 player Bike-to-Bike Intercom up to 700 m / 2,300 ft (in open te
1. If either headset is turned OFF, turn it ON by pressing and holding the CTRL Button until the Blue Light flashes three times. 2. Make sure that both headsets are now flashing slowly in Blue. 3. Pick up one headset and simultaneously press and hold the CTRL Button and MC Button for at least six seconds until the Red Light begins flashing rapidly, indicating it is in Intercom Pairing mode. 4. Repeat Step 3 again for the second scala rider Q2 pro headset. Both headsets should now be flashing rapidly in Red.
When using an earlier scala rider headset as a Passenger headset, Voice Connect Intercom can be initiated only by the scala rider Q2 pro headset. Manual Connect Intercom can be initiated from either headset by pressing the MC button for scala rider Q2 pro and CTRL button for any earlier scala rider headset. RESET INTERCOM PAIRING You can delete all of the headset’s Intercom pairings at any time. 1.
1. Turn on your GPS device. 2. With the scala rider Q2 pro headset turned ON, press and hold the volume up Button for at least six seconds until the Red and Blue Lights begin flashing simultaneously. 3. Search for Bluetooth headsets on your GPS device by following the device’s instructions. The headset will be listed as “scala rider Q2 Pro“. Please consult your GPS device’s User Manual for more information. 4. If your GPS device prompts for a PIN or Passkey enter 0000 (four zeros). 5.
1. Use the enclosed Allen Wrench to remove both Allen screws and release the Helmet Clamp’s back plate. 2. Determine the location on the helmet where the Helmet Clamp must be attached. 3. Adjust the Helmet Clamp’s location on the Helmet so that the microphone is located opposite your mouth. You may need to reposition the Clamp repeatedly until you identify the best spot. The microphone must be positioned vertically and not horizontally (Be sure to clean the selected area prior to the gluing process). 4.
ATTACHING: Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place. REMOVING: Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand. We recommend that you remove the headset from the helmet when not in use.
MC BUTTON CONNECT: Double tap the MC Button MC Button A Buddy Intercom call will be established. To end the Buddy Intercom call, double tap the MC Button again. NOTE: While the Intercom is on, the Redial and Voice Dial functions will be disabled. NOTE: When using a scala rider Headset (not a Q2 pro version) as a Passenger headset, Voice Connect Intercom can be initiated only by the scala rider Q2 pro headset. Manual Connect Intercom can be initiated from either headset.
STATUS LIGHT STATES English During Standby, press and hold the Volume Up Button for three seconds and you will hear a beep: • One beep – Voice Connect set to Primary Buddy • Two beeps – Voice Connect set to Secondary Buddy None Headset is off Alternating red and Blue flashes Mobile phone Pairing mode Simultaneous red and Blue flashes GPS Pairing mode Rapid Red flashes Intercom Pairing mode Tap the CTRL Button or speak loudly any word of your choice during an incoming call.
strongest signal available for the FM station you wish to listen to, no matter where you are riding. This allows you to leave your hands on the handlebars at all times with no need to adjust the radio station frequency while you are in motion. To use the RDS feature while the Radio is on, press and hold the Volume Up and Volume Down Buttons simultaneously for 3 seconds. The headset will display a solid blue light indicating that the RDS function is enabled.
NOTE: If your A2DP source is integrated inside your Mobile Phone, then you should pair it with your headset as described earlier in section: SET UP FOR MOBILE PHONE CALLS: PAIRING 1. Turn on your MP3 Player or Adapter, and make sure that its Bluetooth function is activated. 2. With the scala rider Q2 pro headset turned ON, press and hold the CTRL Button for at least six seconds until the Red and Blue Lights begin alternating rapidly: 3.
cable holder. Make sure that the cable plug clicks into place. 7. Tuck the MP3 cable into the hook of the MP3 cable holder. 8. In order to use your MP3 player, power on the headset to have it on Standby mode, flashing slowly in Blue. NOTES: • Operate the MP3 Player device by using its buttons (FF/REW/PLAY/PAUSE). • Volume can only be adjusted through the MP3 Player. • Any other audio connection will automatically mute the MP3 Player.
IC RF Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
and that you have given up substantial rights by not returning the Device for a full refund (see refund option below). Disclaimer of Warranty CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. THE DEVICE AND ITS ACCESSORIES ARE PROVIDED “AS IS” AND “AS AVAILABLE” WITHOUT WARRANTY OF ANY KIND BEYOND THOSE ASSUMED IN THE ENCLOSED MANUAL.
