™ Solo ™ communication in motion ™ Gebrauchsanleitung Guide d’Utilisation Guida di Avvio Guia de Usario User Guide
© Cardo Systems, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Cardo Systems, Inc. is under license. Other trademarks and trade names are those of their respective owners.
Dear Biker, Congratulations, and thank you for choosing the scala rider Solo Bluetooth® Headset for bikers. CONTENTS OF RETAIL BOX English INTRODUCTION Volume Up Headset Cover tongue & Charging Jack The scala rider Solo headset offers the following communication options: 1. Bluetooth headset for mobile phone communication, supporting Headset* and Handsfree* profiles (10m / 33 ft. range) 2. Transmitting GPS navigation instructions from a Bluetooth enabled GPS device 3.
SET UP AND CONFIGURATION Wall Charger Allen Wrench Velcro Pads GPS MP3 Cable Mobile Phone MP3 Cable Holder MP3 Player Glue Plate Pre-moistened Towelette Carry-Pouch Microphone sponges Flat sponge for full-face helmets and round sponge for other helmet types User Guide, including Warranty and Registration form IMPORTANT: The scala rider Solo is a water-resistant device, designed for use under moderate rain or snow conditions.
2. With the scala rider Solo headset turned OFF, press and hold the CTRL Button until the Red and Blue Lights begin rapidly alternating. 3. Search for Bluetooth headsets on your GPS device by following the device’s instructions. Please consult your GPS device’s User Manual for more information. NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode. 4. If your GPS device prompts for a PIN or Passkey enter 0000 (four zeros).
Standard Method 1. Use the enclosed Allen Wrench to loosen the two screws on the Back Plate. 2. Slide the Back Plate between the internal padding and the external shell of the helmet. 3. Adjust the clamp’s location so that the microphone is located opposite your mouth and then tighten the screws. You may need to reposition the Clamp repeatedly until you identify the best spot. The microphone must be positioned vertically and not horizontally.
Cable AUDIO SOURCES AND PRIORITIES Speaker B Speaker B Speaker A ATTACHING AND REMOVING THE HEADSET FROM THE HELMET CLAMP Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place. REMOVING: Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand. We recommend that you remove the headset from the helmet when not in use.
INITIATING AND RECEIVING MOBILE PHONE CALLS Voice Recognition – VR (VOX) The VR feature allows you to answer or reject incoming calls by voice Control without having to remove your hands from the handlebars. The default mode of this feature is ON (enabled). Each time you switch off and turn on the headset, the VR feature will be automatically enabled. To disable / enable the VR feature press and hold the Volume Up and Volume Down simultaneously for three seconds during Standby.
NOTE: Operate the MP3 Player device by using its buttons (FF/REW/ PLAY/PAUSE). Volume can only be adjusted through the MP3 Player. Any other audio connection will automatically mute the MP3 Player. The audio signal will return only when headset is once again in Standby mode. SUPPORT English on the MP3 cable holder should be fixed into corresponding indentations on clamp. 3.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Operation is subject to the following two conditions: • Reorient or relocate the receiving antenna.
WAIVER AND GENERAL RELEASE By using the scala rider Solo you will waive substantial legal rights including the right to sue. Please read the following carefully before using the device. If you do not accept all terms of this agreement, you should immediately return the product for a full refund. By using the headset you agree to be bound to this agreement and forfeit the right to sue.
signing or manufacturing the Device; (c) these risks and dangers may arise from foreseeable or unforeseeable causes. You hereby assume all risks and dangers and all responsibility for any losses and/or damages, whether caused in whole or in part by the negligence or other conduct of others, including the Company. 5.
