User manual

ATTENTION
CAREL bases the development of its products on several years’ experience in the HVAC
field, on continuous investment in technological innovation of the product, on rigorous
quality procedures and processes with in-circuit and function tests on 100% of its
production, on the most innovative production technologies available on the market.
CAREL and its branch offices/affiliates do not guarantee, in any case, that all the aspects
of the product and the software included in the product will respond to the demands of
the final application, even if the product is built according to state-of-the-art techniques.
The client (builder, developer or installer of the final equipment) assumes every
responsibility and risk relating to the configuration of the product in order to reach the
expected results in relation to the specific final installation and/or equipment.
CAREL in this case, through specific agreements, can intervene as consultant for the
positive result of the final start-up machine/application, but in no case can it be held
responsible for the positive working of the final equipment/apparatus.
The CAREL product is a state-of-the-art product, whose operation is specified in the
technical documentation supplied with the product or can be downloaded, even prior
to purchase, from the website www.carel.com.
Each CAREL product, in relation to its advanced technological level, needs a phase of
definition / configuration / programming / commissioning so that it can function at its
best for the specific application. The lack of such phase of study, as indicated in the
manual, can cause the final product to malfunction of which CAREL cannot be held
responsible.
Only qualified personnel can install or carry out technical assistance interventions on the
product.
The final client must use the product only in the manner described in the
documentation related to the product itself.
Without excluding proper compliance with further warnings present in the manual, it is
stressed that in any case it is necessary, for each CAREL product:
 Not allow the electronic circuits getting wet. Rain, humidity and all types of liquids or
condensate contain corrosive mineral substances that can damage the electrical
circuits. In any case, the product should be used and stored in environments that
respect the temperature and humidity limits specified in the manual;
 Not to install the device in a particularly hot environments. Temperatures that are
too high can shorten the duration of the electronic devices, damaging them and
distorting or melting the parts in plastic. In any case, the product should be used and
stored in environments that respect the temperature and humidity limits specified in
the manual;
 Not to try to open the device in any way different than that indicated in the manual;
 Not to drop, hit or shake the device, because the internal circuits and mechanisms
could suffer irreparable damage.
 Not to use corrosive chemical products, aggressive solvents or detergents to clean
the device;
 Not to use the product in application environments different than those specified in
the technical manual.
All the above reported suggestions are also valid for the control, serial boards,
programming keys or however for any other accessory in the CAREL product portfolio.
CAREL adopts a continuous development policy. Therefore, CAREL reserves the right to
carry out modifications and improvements on any product described in this document
without prior notice.
The technical data in the manual
can undergo modifications
without forewarning.
The liability of CAREL in relation to its own product is governed by CAREL’s general
contract conditions edited on the www.carel.com and/or by specific agreements with
clients; in particular, within the criteria consented by the applicable norm, in no way will
CAREL, its employees or its branch offices/affiliates be responsible for possible lack of
earnings or sales, loss of data and information, cost of replacement goods or services,
damage to objects or persons, work interruptions, or possible direct, indirect, accidental,
patrimonial, coverage, punitive, special or consequential damage in any way caused, be
they contractual, out-of-contract, or due to negligence or other responsibility originating
from the installation, use or inability of use of the product, even if CAREL or its branch
offices/affiliates have been warned of the possibility of damage.
DISPOSAL
INFORMATION FOR THE USERS REGARDING THE CORRECT
HANDLING OF WASTE ELECTRIC AND ELECTRONIC EQUIPMENT
(WEEE)
With reference to European Parliament and Council Directive 2002/96/EC issued on 27
January 2003 and the related national implementation legislation, please note that:
 WEEE cannot be disposed of as municipal waste, said waste must be collected
separately;
 the public or private waste collection systems defined by local legislation must be
used. Moreover, the equipment can be returned to the distributor at the end of its
working life when buying new equipment;
 this equipment can contain hazardous substances: improper use or incorrect
disposal of such may have negative effects on human health and on the
environment;
 the symbol (crossed-out wheeley bin) shown on the product or on the packaging
and on the instruction sheet indicates that the equipment has been introduced
onto the market after 13 August 2005 and that it must be disposed of separately;
 in the event of illegal disposal of electrical and electronic waste, the penalties are
specified by local waste disposal legislation.
Materials warranty: 2 years (from the date of production, excluding consumables).
Type-approval: the quality and safety of CAREL S.P.A. products are guaranteed by the
design system and ISO 9001 certified production.
ATTENTION: separate the probe cables and the digital input cables as much as possible
from the inductive load and power cables to prevent possible electro-magnetic
interference. Never introduce power cables and signal cables (including those of electric
control board) into the same cable troughs.
3