User's Guide
Table Of Contents
- 1 Overview
- DRYVIEW CHROMA Imager at your Site
- Intended Use
- Imager Features
- CHROMA Media
- Network Interfaces
- Power Management Features
- Configuring and Monitoring the System (using the Web Portal)
- Enhancing Serviceability with Remote Monitoring
- How the Imaging System Works
- System Components
- DICOM Interface
- Imager
- Back View
- Control Panel
- Display Screen
- Using the Web Portal to Access Additional Functionality
- Accessing the Web Portal
- Agency Compliance
- Reference Information
- User Guide Conventions
- 2 Working with the Media and Ink
- Handling the CHROMA Media (Film or Paper)
- Working with the Loaded Media
- Viewing the Loaded Media Size
- Monitoring the Amount of Loaded Media
- Checking the DICOM Interface for the Requested Media Size
- Understanding How Media is Selected for Print Requests
- Loading the Media Cassette (Cut Sheets)
- Loading the Roll Paper
- Placing the Roll Paper on the Spindle
- Loading the Roll Paper into the Imager
- Readying the Imager to Print to Roll Paper
- Cutting the Roll Paper
- Changing the Media in the Imager
- Handling a Print Request with a Different Requested Media
- Handling a Media Change when the New Print Request is Urgent
- Replacing the Cut Sheet Media
- Replacing the Roll Paper
- Working with Ink
- Extending the Life of Ink Cartridges During Periods of Inactivity or Low Use
- Checking the Ink Levels
- Replacing the Ink Cartridges
- Checking the Maintenance Tank Levels
- Replacing the Maintenance Tanks
- Replacing the Ink Maintenance Tank (Tank 1)
- Replacing the Borderless Maintenance Tank (Tank 2)
- 3 System Settings and Status
- Changing the Imager’s Date and Time
- Changing Configuration Items in Maintenance Mode
- Working in Maintenance Mode
- Imager Language
- Units of Measurement
- Temperature Units
- Auto Cleaning
- Alert Settings
- Number of Minutes Before Automatic Sleep Mode
- Return Settings to the Defaults
- Checking Imager Status
- Print a Status Sheet
- View Imager Status
- Firmware Version
- Ink Levels
- Maintenance Tank Levels
- Job History
- Total Print Count
- Setting up Automatic Nozzle Check
- Setting up Roll Paper Settings
- Media Selection
- Roll Paper Margins
- Paper Size Check
- Paper Skew Check
- Set Roll Paper Tension
- Optimizing the Look of the Image
- Optimizing Grayscale Images on Film
- Optimizing Color Images on Paper
- Optimizing Grayscale Images on Paper
- 4 Maintenance and Troubleshooting
- Overview
- Keeping the Imager Clean
- Clean the Outside
- Uneven Prints: Clean the Cassette Printing Path
- “Dirty” Prints: Clean the Inside
- White Powder on the Platen: Clean the Platen
- Smudged Prints from the Roller
- Running a Nozzle Check to Avoid or Correct Print Issues
- Checking and Cleaning the Nozzles
- Working with the Print Head
- Overview
- Clean the Print Head
- Align the Print Head
- Correcting Paper Cutting Problems
- Correcting Errors
- Introduction
- Messages at the Imager Display Screen and Suggested Actions
- Roll Paper Errors
- Maintenance or Service Call is Required
- Troubleshooting
- Imager is Not Printing
- Imager Sounds Like it is Printing, but Nothing Prints
- Prints Do Not Look as Expected
- Top Line of the DICOM Interface Screen is Blank
- Feeding or Ejecting Problems/Media Jams
- Clearing a Roll Paper Jam
- An Icon on my Print Indicates a Sizing Issue, or some of the Image or Information is Cut Off
- Miscellaneous Issues
- Restarting the Imager
- The DICOM Interface is Non-Responsive (How to Restart)
- Restoring the System Software - Ghosting
- Calling for Support
- 5 Specifications
- Dimensions and Clearance
- Packed Dimensions
- Environmental Recommendations
- Temperature
- Relative Humidity
- Surface Levelness
- Acoustical Noise
- Network Requirements
- Power Requirements
- Power Consumption -Imager
- Power Consumption -DICOM Interface
- Ink Cartridges
- Cartridge Life
- Temperature
- Capacity
- Weight
- Media
- Environmental
- Storage
- Publication History
2-12 9G4260_en 2012-01-27
Working with the Media and Ink
Changing the Media in the Imager
Handling a Print
Request with a
Different Requested
Media
If a print job requires a different media from the media that is currently
loaded in the imager, the new size appears on the DICOM interface
screen to alert you to install the requested size.
See “Understanding How Media is Selected for Print Requests” on
page 2-3 for more information about image sizes and requested media
sizes.
The DICOM interface screen displays the loaded size on the top row and
the requested size on the lower row. For example:
In this example, the 28 x 35 cm (11 x 14 in.) media is loaded, but a print
job has arrived at the CHROMA imager requesting A3 media.
If there are current jobs to
print on the loaded media...
If there are no current
jobs for the loaded
media...
1. Wait until the current jobs finish
printing.
2. Replace the loaded media with
the requested media. See
“Replacing the Cut Sheet
Media” on page 2-14 or
“Replacing the Roll Paper” on
page 2-16.
The DICOM interface senses
the change; the DICOM
interface screen changes, and
the new job automatically prints.
Replace the loaded media with
the requested media. See
“Replacing the Cut Sheet
Media” on page 2-14 or
“Replacing the Roll Paper” on
page 2-16.
The DICOM interface senses the
change; the DICOM interface
screen changes, and the new job
automatically prints.
11 x 14 [*** ]
A3
Represents the
amount of the
loaded media
remaining
The loaded media size is
28 x 35 cm (11 x 14 in.)
The requested media
size is A3
SHORT TERM CONFIDENTIAL