Datasheet

ManualsBrandsCarlo Gavazzi ManualsRelaysSolid State Relay RGC1S, SPST-NO, 50A, 600V, Clamp Terminal

Specifications are subject to change without notice (11.04.2016) 1

Solid state relay

Number of poles

Switching mode

Rated operational voltage

Control voltage

Rated operational current

Connection type for control

Connection type for power

Connection configuration

Protection

Options

• Product width ranging from 22.5mm to 70mm

• Partial load failure detection

• Zero cross switching

• Ratings up to 600VACrms & 85AACrms @ 40

• Up to 18000A

s for I

t and 1200Vp for blocking voltage

• Control voltage range: 4 - 32 VDC

• Local or remote current set-point

• LED indications for the different faults

• Alarm signal output for SSR or load circuit malfunction

• IP20 protection

• Integrated voltage transient protection with varistor

• RoHS compliant

• Short circuit current rating 100kArms

Product Description

Ordering Key

This slim RG design is capable

of detecting various failure

modes occuring to the heaters

and also to the product itself.

Failures which can be detected

include partial load failure,

heater loss, open circuit SSR,

short circuit SSR and SSR

over temperature. A normally

closed, potential free alarm,

opens in the event of a system

or power semiconductor fault.

A load current setpint has to be

TEACHed to the SSR either

locally by the TEACH button

on the front of the device or

remotely through the provided

terminal.

This product is available either

with integrated heatsink

(RGC1S series) and also with-

out heatsink (RGS1S series).

The minimum product width is

22.5mm. The control and aux-

iliary terminals are double box

clamps to facilitate safe loop-

ing whilst the power terminals

are either screw terminals or

box clamps depending on the

model selected.

Solid State Relays

1-Phase Integrated Heatsink

Integrated Current Monitoring

Types RGC1S

RGC 1 S 60 D 30 G K E P _

Note: Specifications stated at 25°C unless specified.

Ordering Key

1-Phase Switching Rated V, Control Rated current

@ 40˚C Connection Connection Connection Protection

SSR mode Blocking V* voltage I

t data input output configuration

RGC1: S: Zero 60:600VAC D: 4-32VDC 20: 23AAC, 525A

s G: Box K: Screw E: Contactor P: Over-

with heatsink cross with +10% -15%, 25: 25AAC, 1800A

s Clamp G: Box U: SSR temperature

current 1200Vp 26: 25AAC, 18000A

s Clamp protection

sensing 30: 30AAC, 1800A

31: 30AAC, 6600A

41: 43AAC, 18000A

61: 65AAC, 18000A

90: 85AAC, 18000A

* Rated voltage, Blocking voltage

1: refer to derating curves

Summary of content (22 pages)

PAGE 1
Solid State Relays 1-Phase Integrated Heatsink Integrated Current Monitoring Types RGC1S • • • • • • • • • • • • • Product Description This slim RG design is capable of detecting various failure modes occuring to the heaters and also to the product itself. Failures which can be detected include partial load failure, heater loss, open circuit SSR, short circuit SSR and SSR over temperature. A normally closed, potential free alarm, opens in the event of a system or power semiconductor fault.
PAGE 2
RGC1S Selection Guide Rated output voltage, Blocking voltage Connection control/ power Control voltage Configuration 600VAC, 1200Vp Box Clamp/ Screw 4 - 32VDC Rated output voltage, Blocking voltage Connection control/ power 600VAC, 1200Vp Box Clamp/ Box Clamp Rated operational current (I2t value in brackets) 23AAC (525A2s) 25AAC (1800A2s) 30AAC (1800A2s) E RGC1S60D20GKEP RGC1S60D25GKEP RGC1S60D30GKEP RGC1S60D31GKEP Control voltage Configuration Rated operational current (I2t value in br
PAGE 3
RGC1S General Specifications ≤ 20 VAC Latching voltage (across L1-T1) Operational frequency range Power factor Touch protection LEDs status indication Supply ON Control ON Load ON Fault Pollution degree Over-voltage category Isolation Input to Output 45 - 65 Hz > 0.
PAGE 4
RGC1S Output Power Dissipation 100W RG...90 90W 80W Power Dissipation in W 70W RG...61 60W 50W 40W RG...41 RG...25,30 30W RG...20 RG...26, 31 20W 10W 0W 0A 5A 10A 15A 20A 25A 30A 35A 40A 45A 50A 55A 60A 65A 70A 75A 80A 85A Load current in AACrms Current Derating (UL508) RGC1S..90 RGC1S..61 RGC1S..41 RGC1S..30, 31 RGC1S..25, 26 RGC1S..20 85 84.3 58 30 30 30 0 75 50 30 27 25.
PAGE 5
RGC1S Derating vs. Spacing Curves RGC1S.. 20 Load Curre ent in AAC 35 30 25 20 0mm 15 5mm 10 10mm 5 20mm & over 0 0 10 20 30 40 50 60 70 80 Surrounding Ambient Temperature in °C RGC1S.. 25, RGC1S..26 30 Load Current in AAC 25 0mm 20 5mm 10mm 15 22.5mm & over 10 5 0 0 10 20 30 40 50 60 70 80 Surrounding Ambient Temperature in °C Specifications are subject to change without notice (11.04.
PAGE 6
RGC1S Derating vs. Spacing Curves RGC1S.. 30, RGC1S..31 Load Curren nt in AAC 35 30 25 0mm 20 5mm 10mm & over 15 Stand alone unit 10 0 10 20 30 40 50 60 70 80 Surrounding Ambient Temperature in °C RGC1S.. 41 6 Specifications are subject to change without notice (11.04.
PAGE 7
RGC1S Derating vs. Spacing Curves RGC1S.. 61 75 Load Current in AAC 70 65 60 0mm 55 50 10mm & over 45 Stand alone unit 40 35 30 0 10 20 30 40 50 60 70 80 Surrounding Ambient Temperature in °C RGC1S.. 90 Load Curre ent in AAC 90 85 80 75 70 65 0mm 60 10mm & over 55 Stand alone unit 50 0 10 20 30 40 50 Surrounding Ambient Temperature in °C Specifications are subject to change without notice (11.04.
PAGE 8
RGC1S Terminal Markings RG...41GGEP RG...61GGEP RG...90GGEP RG...20GKEP RG...25GKEP RG...26GGEP RG...30GKEP RG...31GKEP 1 11 L1 12 1 A1 11 RG...41GGUP RG...
PAGE 9
RGC1S Connection Diagram for Separate Alarm Outputs Alarm out SSR 1 Alarm out SSR 2 Alarm out SSR n Us: 24VDC Ua: max. 35VDC Uc:4-32VDC Uc: 4TEACH) - 32VDC (only for Remote Ground Terminal Uc SSR 1: 4 - 32VDC Uc SSR 2: 4 - 32VDC Connection Diagram for Series Alarm Outputs Uc SSR n: 4 - 32VDC Alarm out Us: 24VDC Ua: max. 35VDC Uc:4-32VDC Uc: 4TEACH) - 32VDC (only for Remote Ground Terminal Uc SSR 1: 4 - 32VDC Specifications are subject to change without notice (11.04.
PAGE 10
RGC1S Alarm LED Indications (Red LED) Flashes Description of Fault Timing Diagram 3s 1 Locked TEACH 2 Open SSR / Heater 3 SSR Overtemperature 4 SSR Short Circuit 3s 3s 3s 0.5s 50% No TEACH setpoint 100% Partial Load Failure Mode of Operation Introduction: The RGC1S must have a stored current setpoint to operate as a Solid State Relay with a Sensing function. The current setpoint is the nominal operating current that is expected through the SSR when all heater loads are functioning properly.
PAGE 11
RGC1S Mode of Operation (cont.
PAGE 12
RGC1S Mode of Operation (cont.) Fault Conditions Line Voltage; 1L1 Load Voltage; 2T1 >16.67% Load Current Control Voltage; IN 2 Supply Voltage; A1, A2 Green LED SSR Overtemperature Alarm Output (NC); 11, 12 Open Open Open Open Open Yellow LED Red LED half intensity full intensity Condition: Partial load failure Condition: overtemperature Partial Load Failure This occurs when the load current decreases by more than 16.67% as compared to the stored setpoint.
PAGE 13
RGC1S Agency Approvals and Conformances Conformance & Approvals Short Circuit Current Rating EN/IEC 60947-4-3 EN/IEC 62314 UL508 Listed (E172877) cUL Listed (E172877) 100kA, UL508 Electromagnetic Compatibility EMC Immunity Electrostatic Discharge (ESD) Immunity Air discharge, 8kV Contact, 4kV Electrical Fast Transient (Burst) Immunity Output: 2kV, 5kHz Input: 1kV, 5kHz Electrical Surge Immunity Output, line to line, 1kV Output, line to earth, 2kV DC lines, line to line, 500V DC lines, line to earth, 500
PAGE 14
RGC1S Filtering - EN / IEC 55011 Class A compliance (for class B compliance contact us) Part Number Suggested filter for compliance Maximum Heater current RGC1S60D20GKEP RGC1S60D25GKEP RGC1S60D26GGEP RGC1S60D30GKEP RGC1S60D31GKEP RGC1S60D41GG.P RGC1S60D61GG.
PAGE 15
RGC1S Connection Specifications POWER CONNECTIONS: 1/L1, 2 /T1 Use 75°C copper (Cu) conductors Stripping Length (X) Connection type Rigid (Solid & Stranded) UL/ cUL rated data RG..20, 25, 30, 31GKEP RG..26GGEP 12mm M4 screw with captivated washer RG..41GG.P; RG..61GG.P; RG..90GGEP 11mm M5 screw with box clamp X 2 x 2.5..6 mm2 1 x 2.5..6 mm2 2 x 14.. 10 AWG 1 x 14.. 10 AWG 2 x 1.0 ... 2.5mm2 2 x 2.5..4mm2 1 x 1.0..4mm2 2 x 18.. 14 AWG 1 x 18.. 12 AWG 2 x 14.. 12 AWG 2 x 1.0 ... 2.5mm2 2 x 2.5..
PAGE 16
RGC1S Dimensions: RGS1S RGC1S60D20GKEP RGC1S60D25GKEP Housing width tolerance +0.5mm, -0mm…as per DIN43880 All other tolerances: ± 0.5mm All dimensions in mm 16 Specifications are subject to change without notice (11.04.
PAGE 17
RGC1S Dimensions: RGC1S60D26GGEP RGC1S60D30GKEP , RGC1S60D31GKEP Housing width tolerance +0.5mm, -0mm…as per DIN43880 All other tolerances: ± 0.5mm All dimensions in mm Specifications are subject to change without notice (11.04.
PAGE 18
RGC1S Dimensions RGC1S60D41GGEP RGC1S60D61GGEP RGC1S60D90GGEP (fan to be supplied externally - no terminations provided on the RG module) Housing width tolerance +0.5mm, -0mm…as per DIN43880 All other tolerances: ± 0.5mm All dimensions in mm 18 Specifications are subject to change without notice (11.04.
PAGE 19
RGC1S Dimensions RGC1S60D41GGUP RGC1S60D61GGUP Housing width tolerance +0.5mm, -0mm…as per DIN43880 All other tolerances: ± 0.5mm All dimensions in mm Specifications are subject to change without notice (11.04.
PAGE 20
RGC1S Installation Instructions Y1 = 50mm 20mm X 20mm X = 20mm X =XRefer to Derating vs. Spacing Curves Mounting Mounting on on DIN DIN rail rail Y2 = 100mm Dismounting Dismounting from from DIN DIN rail rail 50mm 20 Specifications are subject to change without notice (11.04.
PAGE 21
RGC1S Short Circuit Protection Protection Co-ordination, Type 1 vs Type 2: Type 1 protection implies that after a short circuit, the device under test will no longer be in a functioning state. In type 2 co-ordination the device under test will still be functional after the short circuit. In both cases, however the short circuit has to be interrupted. The fuse between enclosure and supply shall not open. The door or cover of the enclosure shall not be blown open.
PAGE 22
RGC1S Type 2 Protection with Miniature Circuit Breakers (M. C. B.s) Solid State Relay ABB Model no. for ABB Model no. for Wire cross Minimum length of type Z - type M. C. B. (rated current) B - type M. C. B. (rated current) sectional area [mm2] Cu wire conductor [m]8 RG..20 1 pole S201 - Z4 (4A) S201 - Z6 UC (6A) S201 - B2 (2A) S201 - B2 (2A) 1.0 1.0 1.5 21.0 21.0 31.5 1 pole S201 - Z10 (10A) S201-B4 (4A) 1.0 1.5 2.5 7.6 11.4 19.0 S201 - Z16 (16A) S201-B6 (6A) 1.0 1.5 2.5 4.0 5.2 7.