Datasheet

ManualsBrandsCarlo Gavazzi ManualsAutomationSoft Starter, Rse 3A 400V 1.5kW 24 ... 480VAC 24 ... 110VDC

Specifications are subject to change without notice (07.10.2003) 1

Type Rated operational Rated operational Control voltage

voltage U

current I

RSE: E-series, 22: 127/220 VACrms, 50/60 Hz 03: 3 A -B: 24 to 110 VAC/DC

motor controller 40: 230/400 VACrms, 50/60 Hz 12: 12 A & 110 to 480 VAC

48: 277/480 VACrms, 50/60 Hz

60: 346/600 VACrms, 50/60 Hz

*) The control voltage should never be higher than the rated operational voltage.

Solid State Relay

Motor controller

E-line housing

Rated operational voltage

Rated operational current

Control voltage

Ordering Key

Motor Controllers

AC Semiconductor Motor Controller

Types RSE 22 .. - B, RSE 4. .. - B, RSE 60 .. - B

RSE 40 03 - B

• Soft starting and stopping of 3-phase

squirrel cage motors

• Rated operational voltage: Up to 600 VACrms, 50/60 Hz

• Rated operational current: 3 A or 12 AAC 53 b

• Potential-free control input

• LED-indications for supply and operation

• Transient overvoltage protection built-in

•Integral bypassing of semiconductors

Product Description

Compact easy-to-use AC

semiconductor motor con-

troller. With this controller 3-

phase motors with nominal

load currents up to 12 A can

be soft-started and/or soft-

Type Selection

stopped. Starting and stop-

ping time as well as initial

torque can be independently

adjusted by built-in potentio-

meters.

Input Specifications (Control Input)

Control voltage U

A1-A2: 24 - 110 VAC/DC ±15%,

12 mA

A1-A3: 110 - 480 VAC ±15%,

5 mA

Rated insulation voltage 630 V rms

Overvoltage cat. III (IEC 60664)

Dielectric strength

Dielectric voltage 2 kVAC (rms)

Rated impulse withstand volt. 4 kV (1.2/50 µs)

Output Specifications

Utilization category AC-53b Integral bypassing

of semiconductors

Overload current profile

(overload relay trip class)

RSE ..03-B 3A: AC-53b:3-5:30

RSE ..12-B 12A: AC-53b:3-5: 180

Min. load current

RSE ..03-B 100 mAAC rms

RSE ..12-B 200 mAAC rms

Summary of content (4 pages)

PAGE 1
Motor Controllers AC Semiconductor Motor Controller Types RSE 22 .. - B, RSE 4. .. - B, RSE 60 ..
PAGE 2
RSE 22 .. - B, RSE 4. .. - B, RSE 60 .. - B Supply Specifications General Specifications Power supply Rated operational volt. (Ue) through terminals L1-L2-L3 22 Accuracy Ramp up Overvoltage cat. III (IEC 60664) (IEC 60038) 127/220 VAC rms ±15% 50/60 Hz -5/+5 Hz 40 230/400 VAC rms ±15% 50/60 Hz -5/+5 Hz 48 277/480 VAC rms ±15% 50/60 Hz -5/+5 Hz 60 346/600 VAC rms ±15% 50/60 Hz -5/+5 Hz Voltage interruption ≤ 40 ms Dielectric voltage None Rated impulse withstand volt. 4 kV (1.
PAGE 3
RSE 22 .. - B, RSE 4. .. - B, RSE 60 .. - B Housing Specifications Dimensions Weight Housing material Colour Terminal block Colour Bottom clip Colour Diode cover Colour Front knob Colour 270 g PC/ABS Blend Light grey PBTP Black POM Black PC Grey Transparent PC Black All dimensions in mm Applications Changing from Direct ON Line start to soft start (Line controlled soft-start) (Fig. 1 & Fig.
PAGE 4
RSE 22 .. - B, RSE 4. .. - B, RSE 60 .. - B Applications Note: Table is valid for ambient temperature 25°C. For higher ambient temperature add 5%/°C to values in the tables. The shaded areas in the tables are for blocked rotor. Do not repeat rampings with blocked rotor. Time between rampings To prevent the semiconductors from overheating, a certain time between ramping should be allowed. The time between rampings depends on the motor current during ramping and ramp time (see tables below). RSE ..