Product Brochure
Orange Low Voltage Boxes/Brackets
39
Dual Voltage Box/Bracket
Here’s a smart alternative where you
would normally use separate high and
low voltage boxes. Designed to fit a
standard two-gang faceplate, this
component combines an electrical
box and low voltage bracket into a
single unit for fast, easy installation. No alignment tools are
required, and easy nail-on mounting provides precise placement
and a professional finished appearance. Resi-Rings accept
3
/
4
"
Resi-Gard
®
fittings only. SC200DV
Low Voltage Adjustable
Brackets
Our Low Voltage Adjustable Brackets
are the perfect solution for tile,
paneling, or stucco. A bracket allows
for quick, easy stud mounting, and a
turn of the screw adjusts to any wall thickness. It’s great for
retrofit/ installation upgrades. Replace the single-gang bracket
with a two-gang bracket, or switch services to a high-voltage
Adjust-A-Box
™
devices. SC100ADJC (shown) and SC200ADJC
Resi-Gard
®
Flexible
Raceway And Fittings
Available in 5 sizes from
3
/
4
" to
2", with factory installed pull tape
in sizes 1" to 2", our Resi-Gard
®
Flexible Raceway provides a main
chase from the main distribution panel to a secondary hub in
the attic or basement. Ideal for easy access to add cable or
service upgrades, or leave empty for future expansion.
Low Voltage Add-On
Bracket
This low voltage bracket pro-
vides a low voltage outlet next
to a previously installed high
voltage outlet. Great for both
new construction and rework, it
attaches easily to most electrical boxes, and is designed to
fit a standard two-gang faceplate. Resi-Rings accept
3
/
4
"
Resi-Gard
®
fittings only. SC100SC
Low Voltage Brackets
Here’s the fast installation choice
where only low voltage is
required. Designed to fit a
standard one-, two- or three-gang
faceplate, these low voltage
brackets feature an easy nail-on
mounting or screw-in bracket,
while a hard shell provides increased durability and no
racking. Resi-Rings accept
3
/
4
", 1", and 1
1
/
4
"
Resi-Gard
®
fittings (one-and two-gang versions only).
SC100A, SC200A (shown), and SC300A
Why waste time mounting, then trying to line up separate high voltage and low voltage boxes, and still end up with
something not quite right? Our Dual Voltage Box/Bracket lets you do it all in one fast, easy step with perfect alignment
every time.
Attaching the Add-On Bracket is a “snap.” You just remove the back of the double-sided tape (1), clip the bracket in
place (2), and press on the bracket to secure it against the box (3). Allows for the installation of most rectangular
yoke plates
Our Low Voltage Brackets are open-backed to easily accommodate the bend radiuses required for low voltage
cabling and deep devices such as volume controls, while molded-in ports make it easy to connect flexible race-
way for future-proofing. Or you can use them to tie off cable to the bracket. They can also be attached to wood
or steel studs.
Our Low Voltage Adjustable Brackets
simplify installation with tile,
paneling, or stucco to save you time
and effort. Just use the quick-mount
bracket to clip it to the stud (1),
add a screw for extra support if you
want it (2), then use the adjustment
screw to accommodate wall thickness
(3). Also available in a two-gang
version.
1.
2.
3.
Our complete line of quick-connect couplings, adapters, cable clips, conduit clamps, and solvent cement make for
quick, easy professional installation of Resi-Gard
®
Flexible Raceway.
1.
2.
3.
1.
2.
3.
1.
1.
2.
2.
3.
3.
4.
4.
5.
5.
GM-19_2-01-10:GM-19_2-01-10 7/26/10 9:53 AM Page 39