Operator`s manual

F:\data\John\Docs\Machine Docs\Machine Specs\1790 SPECS.DOC
Carlton Model 1790HD Specifications
General: Hydraulic System:
Weight: 5360 Pounds Hyd Pump Displcmnt: Double Pump Two .4 Cu in
Length: 186 inches Hyd Pump Drv Systm:Direct Drive off Engine Mount
Height: 93 inches Flow: 8.8 GPM Total
Tires: 235/85R16
Ld Rng D3200 Pnd Cap @ 65PSI System Relief: Two Independent 2500 PSI
Axle: Dexter Torflex 8,000 Pound Cap Oil Tank Capacity: 9 Gallons
Brakes: Electric with Breakaway Switch Oil Type: AW32
Hitch: Five Inch Height Adjustable Pintle Valve: DO5 Electric Operated
Fuel Capacity: 24 Gallons Hose: 16,000 PSI Burst - Exceeds SAE 100R2
Battery: 29HVD 650 CCA Oil Filter: 10 Micron Return with Suction Strainer
Jack Stand: 7000 # Cap Screw Type Swing Up
Engine: Drive System:
Manufacturer: Kubota Turbo Charged Diesel V3300T Engine Sheave: 4/5V8.5
Number of Cylinders: Four Jackshaft Sheave: 4/5V14.0
Bore: 3.86 Inches (98 mm) Drive Belt: 4/5V1000
Stroke: 4.33 Inches(110 mm) Cutter Head Shaft: 3 1/2 inches
Displacement: 202.53 Cubic Inches (3.3L)
Maximum RPM: 2800 RPM Feed System:
Horsepower: 88 HP
Torque: 205 Ft Lbs Feed Motors: Two 32 Cubic Inch Displacement
Cooling Medium: Liquid Water/Antifreeze Mixture Flow: 4.4 GPM to Each Motor Independently
Air Cleaner: Two Stage Dry Type Hydraulic Drive: Live – Driven off engine
Oil Filter: Full Flow Spin On Autofeed: Reversing, Digital, Fully Adjustable
Oil Capacity: 14 Quarts Feed Rate: 100 Feet Per Minute
Oil Type: SAE 10W40 CD Grade or Higher Feed Rollers: Two 10 ½” x 17”
Electrical: 12 Volt Springs: Two 19” Tight Wound Powder Coated
Gauges: Oil Pres, Water Temp, Amp, Digital Tach Slide Bearings: Four 16” x 1” x 1” Ryertex
Clutch: Stein Lift Cylinders: Two 2 x 10 with 1” attachments
Discharge: Crank Adjustable Swivel and Height
Bearings: Frame:
Disk Bearings: 2 7/16 inches Tapered Roller Main Trailer Tongue: 3”x 4” with 1/4” wall
Feed Roller Bearings: 2 inches Ball Bearing Main Trailer Frame: 2”x4” with ¼” wall
Disk Shaft: 3 ½ inches Telescoping Tongue: N/A
Feed Roller Shaft: 2 inches Engine Channel Mnts: 4” Channel with 5/16”
web
Infeed Chute: 10ga with 2”x2”x1/8” tube frame
Folding Infeed Tray: 10ga with 4”x11/2” x3/16” bracing
Chipper Disk: Folding Tray Lock: ¾” Spring Loaded Pin
Discharge Chute: 10 gauge
Wheel Diameter: 30 inches Discharge Lock: ¾” Spring Loaded Pin
Wheel Thickness: 1.5 inches Fuel Tank: 10 gauge with baffles rubber mtd
Disk Balance: Precision High Speed Balanced Hydraulic Tank: 10 gauge with baffles rubber mtd
Wheel Speed: 1180 RPM Battery Box: 10 gauge checker plate - lockable
Number of Knives: 2 Fenders: 3/16” checker plate
Knife Dimensions: 5 3/32” x 4 x1/2” Feeder Bar: 1 ½” OD x 1/8” wall - removable
Anvil: 4 ½” x 11”x ½” AR400 Radiator Guards: 2”x4” with 3/16” wall
Chip Throwers: Two 3/8”x 4” x 4” x 11” long Light Brackets: 3/16” with hidden wiring
Axle Mounts:
Cutting Dimensions: Hitch Plate: ¾” Plate adjustable 5” Up/Down
Throat Opening: 9” x 17”
Infeed Hopper Opening: 29” x 48”