Operation Manual

Fitting instructions
1. Place the blanket directly on the mattress, with the control
switch end at the head of the bed.
2. The blanket must be positioned to the mattress in the following
manner. Place the blanket directly on the mattress and ensure
that a space of 10-15cm (4-6 inches) is left between the bottom
edge of the blanket and mattress. Position the blanket on the
bed ensuring the pillow area is clear. (G).
•Eachblanketisttedwith3tietapes.
•Donotstretchthetapetootightly.Allowsome‘give’toavoid
edge distortion. Ensure knots are not tied too tightly so that
they can be undone easily.
3. Pass the rst tape (1) under the corner of the mattress.
4. Thread up through the centre eyelet.
5.Passundertheadjacentcornerandtieotooppositeloop.
6.Repeatforthesecondtape(2)atoppositeendoftheblanket.
7. Pass the centre tape (3) underneath the mattress and tie to
opposite loop.
•Ifthetapeistoolongyoucancutotheends.
› Operating instructions model EB1500 and EB2000
Switchcontrol(C)
1. Illuminated heat setting light
2. Heat levels 2 and 3
3. Heat level 1
4. Braille markings
5. Oposition
6.Footwarmthonlyon/oswitch
How to use switch
1. Ensure the blanket is tted to the bed correctly.
2. Plugthepowerleadintotheclosestsocket,usinganextension
lead if needed to ensure that the lead is not stretched.
Preheating the bed
Move the heat setting on the control switch to heat level 2 and 3,
dependingontheleveloftheheatrequired.Allowapproxima-
tely 60-90 minutes for the blanket to heat the bed thoroughly,
although this time may vary depending on the room temperature
and type of bedding used.
Foot warmth
Models EB1500 and EB2000 have the possibility to switch on
separate and only the foot warmth function. Move the heat setting
on the control switch to the level indicated with foot symbol.
Switchothefootwarmthafterreachingcorrecttemperature.
The foot warmth is too warm for all night use.
All night use
• Movetheheatsettingonthecontrolswitchtoheatlevel1.
• Thissettingwillprovidesafeandcomfortableheattosleepon
all night.
• Thissettingcanbeusedtoairthebed.
Warning!
Always ensure that the heat setting is moved to the OFF position
whenyougetupthenextday,orafterairingthebed.
Braille markings
• Braillemarkingsarelocatedonthebackoftheswitchtohelp
identify the direction of the heat level in the dark, or if visually
impaired.
• Thehighestheatlevel‘preheat’isidentiedby3raisednodu-
les,‘midlevel’by2raisednodulesand‘lowlevel’(allnight)by
1 raised nodule Fitting underblanket.
Fitting instructions
1. Place the under blanket directly on the mattress with the control
switch end at the head of the bed. Do not turn the blanket over,
ensure that the socket on the blanket is facing upwards.
2. Fit the shaped corners to the mattress and turn the elasticated
edges of the skirt under the mattress (E).
3. Ensure all creases are smoothed out and the skirt ts tightly
round the sides of the mattress.
› Cleaning and maintenance
• Examinefrequentlyforanysignsofwearordamagetothe
blanket, switch or cord. In case of damage or misuse, please
return immediately following instruc tions under servicing.
• Iftheblanketfailstoperate,checkthefollowingbeforereturning:
1.
Ensure that the plug and socket have not become disconnected.
2. Checkthatthesupplyplugiscorrectedtottheex.
•Noattemptshouldbemadetorepairtheblanketorhaveit
repaired locally and the switch supplied must never be replaced
other than by the manufacturers since the specialized compo-
nents are not generally available.
Storage
• Tostore,foldcarefullyandplacebackintooriginalpackaging.
• Whenstoringtheblanket,allowittocooldownbeforefolding.
• Donotcreasetheblanketbyplacingitemsontopofitduring
storage.
18•English
Blankets_Manual A5.indd 18 10-10-2011 10:42:09