Operating Instructions and Installation Instructions
10
Setting of the
cars´ basic speed
1 – 10
1 – 10
The setting of the basic speed can be eected individually for one
and/or several cars. The cars which are to be adjusted have to be
positioned on the track. The setting can be carried out on 10 levels
with the 5 LEDs indicating the dierent levels by ashing or perma-
nent lighting.
1 LED lights = low speed
5 LEDs light = high speed
Switch on the Control Unit, place the cars to be adjusted on the
track and press “SPEED”
once. A certain number of LEDs will
now light, showing the speed level last used. Push the “SPEED”
button
as many times until you have reached the speed desired.
Conrm by pressing “ENTER/START”
. A short running light and
the lighting of the middle LED conrms completion of the setting,
g.
.
Setting of cars´
braking performance
1 – 10
1 – 10
(only for cars operated with speed controllers)
The setting of the braking performance can be eected individually
for one and/or several cars. The cars which are to be adjusted have
to be positioned on the track. The setting can be carried out on 10
levels with the 5 LEDs indicating the dierent levels by ashing or
permanent lighting.
1 LED lights = low braking eect
5 LEDs light = high braking eect
Switch on the Control Unit, place the cars to be adjusted on the
track and press “BRAKE”
once. A certain number of LEDs will
now light, showing the brake step last used. Push the “BRAKE” but-
ton
as many times until you have reached the braking perform-
ance desired. Conrm by pressing “ENTER/START”
. A short
running light and the lighting of the middle LED conrms completion
of the setting, g.
.
Setting fuel tank capacity
1 – 10
1 – 10
(only for cars operated with speed controllers)
The setting of the fuel tank capacity in combination with the Pit Lane
(30356) is eected for all cars simultaneously. The setting can be
carried out on 10 levels with the 5 LEDs indicating the dierent lev-
els by ashing or permanent lighting.
1 LED lights = low fuel capacity
5 LEDs light = full tank
Switch on the Control Unit, place the cars to be adjusted on the
track and activate the fuelling function by means of the slide switch
, g.
. Press the “FUEL” button
once. A certain number of
LEDs will now light, showing the fuel capacity last used. Push the
“FUEL” button
as many times until you have reached the fuel
capacity desired. Conrm by pressing “ENTER/START”
. A short
running light and the lighting of the middle LED conrms completion
of the setting, g
.
You can choose between 3 modes via the sliding switch
,
g.
:
• OFF = cars don´t consume any “petrol”
• ON = cars consume “petrol”
• REAL = maximum speed depending on fuel tank capacity / cars
consume “petrol”) (only in combination with Pit Lane 30356 or Pit
Stop Lane 30346 and Pit Stop Adapter Unit 30361)
When driving in “REAL-mode” the car with a full tank is “heavier”,
drives slowlier and shows a lower braking eect; a car with an empty
tank is “lighter”, drives faster and shows a higher braking eect. The
current fuel tank capacity and the “fuel consumption” can only be
displayed in combination with the Driver Display 30353 and Pit Stop
30356.
Pit Lane 30356 Driver Display 30353
The car´s present tank capacity can be read via the bar display with
5 green and 2 red LEDs at the Driver Display. For refuelling drive
your car into the Pit Lane across the refuelling sensor g.
. The
bar display now starts to ash, g.
, and the car can be refuelled
by keeping the lane-change button pushed. g.
. The number of
refuellings are indicated by ashing or lighting of the yellow LEDs,
g.
(also see Driver Display).
Pit Lane 30356 Driver Display 30353
(only in combination with Pit Lane 30356 and Driver Display
30353)
Irrespective of the basic setting of the tank capacity it is possible
to individually set the tank capacity for one or several cars at the
race´s start for the number of laps till the rst pit stop. Push “START/
ENTER” once
; the 5 LEDs at the Control Unit will light perma-
nently, g.
, and the Driver Display´s bar display will ash, g.
.
Clicking the lane-change button at the corresponding speed control-
ler enables you to change the ll level, g.
.
Extended Pit Lane function
Pit Lane 30356
(only in combination with Pit Lane 30356)
It is possible to activate/deactivate the lap counting function in the
Pit Lane 30356 or Pit Stop Lane 30346 with the Pit Stop Adapter
Unit 30361. Switch o the Control Unit, keep “SPEED” button
)
pushed, switch on Control Unit and release “SPEED” button
.
By pushing the button again, 1 or 2 LEDs will light depending on
the setting.
• LED 1 = lap counting function deactivated
• LED 1 + 2 = lap counting function activated
Select the desired setting and push or drive a car across the Pit
Lane Sensor, g.
. The settings will now be adopted. Push
“START/ENTER”
for leaving the settings again.