Adit 3000 CLI REFERENCE MANUAL Part Number: 770-0165 BA Product Release: 1.
Copyright 2007 Carrier Access Corporation. All rights reserved. The information presented in this manual is subject to change without notice and does not represent a commitment on the part of Carrier Access Corporation. The hardware and software described herein are furnished under a license or nondisclosure agreement. The hardware, software, and manual may be used or copied only in accordance with the terms of this agreement.
PREFACE Preface Safety Information CAUTION! WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING THE FOLLOWING: Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
Preface Notices Notices This manual contains important information and warnings that must be followed to ensure safe operation of the equipment. DANGER! A DANGER NOTICE INDICATES THE PRESENCE OF A HAZARD THAT CAN OR WILL CAUSE DEATH OR SEVERE PERSONAL INJURY IF THE HAZARD IS NOT AVOIDED. CAUTION! A CAUTION NOTICE INDICATES THE POSSIBILITY OF INTERRUPTING NETWORK SERVICE IF THE HAZARD IS NOT AVOIDED. WARNING! A WARNING NOTICE INDICATES THE POSSIBILITY OF EQUIPMENT DAMAGE IF THE HAZARD IS NOT AVOIDED.
TABLE OF CONTENTS Table of Contents Preface Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv 1 Introduction Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents reload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents router ospf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53 security-default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-54 security-log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-55 service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . start-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . static-lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 session-target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 strip-digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7 user-id . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents 11 Configuration - Multilink Interface Mode description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2 do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3 end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4 exit . . . . . .
Table of Contents 12 Configuration - Serial Interface Mode description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2 do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3 encapsulation ppp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4 end . . . . . . . . . . . . .
Table of Contents 13 Configuration - IPSec Mode aggressive-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2 authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2 dev-name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2 do . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents 14 Configuration - L2TPC Mode do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2 end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-3 exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-3 firewall . . . . . . . .
Table of Contents 15 Configuration - OSPF Mode area commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-2 compatible rfc1583 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3 do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-4 end . . . . . . . . . . . . . . . . . . . . . .
Table of Contents ppp time-btwn-reconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-23 ppp username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-23 schedule-availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-23 shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents 20 Configuration - VLAN Port Mode do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . history . . . . . . . . . . . . . .
Table of Contents input-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-6 isdn switch-type (PRI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-7 no commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-8 output-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents xviii Adit 3000 CLI - Release 1.
CHAPTER 1 Introduction This Reference Manual covers the Command Line Interface (CLI) for the Adit 3104, Adit 3200 and Adit 3500 products. The chapters are broken down into the User Modes and the Configuration Groups. All commands that are listed in each group are listed in the chapter.
Introduction Overview Overview The Adit 3000 CLI has three command modes, each with access to different command sets. The following displays the basic flow of the Adit CLI. 1-2 Adit 3000 CLI - Release 1.
Introduction Overview Prompt Identifier When you initiate a CLI session it will open in the User Mode, which is clearly indicated by the ">" prompt. At any time you can quickly determine which mode you are in by the prompt (see table above). Command Mode Access Method Prompt Displayed Exit Method User Login Adit 3000> Use the logout command Privileged From User mode, enter the enable command Adit 3000# To exit to User mode, use the exit, or end command.
Introduction Overview Configure Mode Allows users to configure specific features/functions of the Adit. Use the configure terminal command to enter from Configuration Mode. Identified by the (config)# prompt. Note: As the submodes change, the words inside the parentheses are modified. To exit Configuration Mode, the user can enter exit or press Ctrl-Z.
Introduction Command Syntax Conventions Command Syntax Conventions The conventions used to present command syntax are as follows: Convention Description | Vertical bars separate alternative, mutually exclusive elements. Example: (config)# clock source {1|2} {none|ds1 1|ds1 2|ds1 3|ds1 4} [] Square brackets indicate an optional element. Example: (config)# event-history priority [error|fatal|info|notice|warning] {} Braces indicate a required choice.
Introduction Shortcuts Shortcuts Keystroke Up Arrow Description Use the up arrow key to re-display a previously entered command. Select the up arrow repeatedly, to scroll through all the commands entered starting with the most recent. Will move curser one character to the left or right with the arrow. Left and Right Arrow 1-6 ? The question mark will display the current help of the currently command displayed. [Tab] Select the Tab key after entering a partial (but unique) portion of the CLI command.
CHAPTER 2 User Mode The User Mode is the first level of commands after logging in. The User Mode is represented by the Adit 3500> prompt.
User Mode date date Use the date command to display the Adit’s current date. Syntax: Adit 3500> date Example: Adit 3500> date Wed Jan 12 10:37:51 2007 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 enable Use the enable command (at the User Command mode prompt) to enter the Privileged Command mode. Note: Once a correct password has been entered, note the prompt changes from a "Adit 3500>" to "#".
User Mode exit exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode. If the command is entered in a subconfiguration mode (Interface or Routing), this command takes you to the next higher level (example: back to Privileged mode from Interface configuration mode).
User Mode history history Use the history command to display commands that have been entered in this session. Note: This command can be entered in any Configuration mode. Syntax: Adit 3500> history Example: Adit 3500> history date ping 192.168.1.1 -n 4 show version show users show voice-port fxs ping 192.168.1.1 show version history Supported Platforms: Adit 3104, Adit 3200, Adit 3500 2-4 Adit 3000 CLI - Release 1.
User Mode ping ping Use the ping command to send a sequence of ICMP echo request packets to the specified host. If the host variable is omitted, and you are in User mode, the router prompts you for additional information. Note: The ping command, verifies a connection, and is a very important troubleshooting tool. Syntax: Adit 3500> ping {address [-i time] [-l size] [-n count] [-w timeout]|stop} Field Definition address IP address of the host to ping. -i time Specifies the intervals between pings.
User Mode show show For maneuverability through these commands, all command names in blue or italics are hyperlinked.
User Mode show show alarms Use the show alarms command to display the active alarms on the Adit. Syntax: Adit 3500> show alarms [t1 port] {alert|all|critical |info|major|minor} Field Definition t1 port Define a specific port to display alarms. 3104 port range = 1 3500 port range = 1 - 4 alert Filter alert alarms (threshold crossing). all Display all alarms. critical Filter critical alarms. info Filter information alarms. major Filter major alarms (service affecting).
User Mode show show arp Use the show arp command to display the Adit’s ARP (Address Resolution Protocol) table. Syntax: Adit 3500> show arp {all|address|ethernet port} Field Definition all Display entire ARP table. address Display ARP items of the entered IP address. ethernet port Display Ethernet ARP items only. port - Define an Ethernet port number. Range 1 - 2. Example: Adit 3500> show arp ethernet 1 1 192.168.1.1 ether Dynam 00:50:da:59:f0:25 eth_lan Example: Adit 3500> show arp 192.
User Mode show show caclkcd Use the show caclkcd command to display the linux kernel crash dump Syntax: Adit 3500> show caclkcd Example: Adit 3500> show caclkcd ---------------- Begin cacLKCD ----------Jan 1 2003 00:00:44 <3> openrg: unhandled page fault at pc=0x400528c0, lr=0x400 digit-map Show digit-map settings 52890 (bad address=0x30303038, code 245)Show various interfaces pc : [<400528c0>] lr : [<40052890>] No Show l r7 : 4006bb9c r6 : 30303038 r5 : 4006bb9c r4 : 4006bc1c port-trigger r3 : 30303030
User Mode show show config dynamic-dns Use the show config dynamic-dns command to display the dynamic DNS configuration. Syntax: Adit 3500> show config dynamic-dns Example: Adit 3500> show config dynamic-dns dynamic-dns username admin hostname Host1 dynamic-dns interface eth-2 no dynamic-dns offline enable no dynamic-dns wildcard enable no dynamic-dns backup-mx enable no dynamic-dns mail-exchanger Supported Platforms: Adit 3104, Adit 3200, Adit 3500 2-10 Adit 3000 CLI - Release 1.
User Mode show show controller t1 Use the show controller t1 command to display the performance statistics of the DS1. Syntax: Adit 3500> show controller t1 port Field Definition port DS1 (T1) interface.
User Mode show show dhcp-leases Use the show dhcp-leases command to display the DHCP lease table. Syntax: Adit 3500> show dhcp-leases Example: Adit 3500> show dhcp-leases Ethernet 1 Hostname : new-host IP:192.168.1.10 MAC:00:00:ff:ff:00:00 Type:static Expires-In:0 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 show digit-map Use the show digit-map command to display the Digit Map settings.
User Mode show show interface description Use the show interface description command to display the interface information. Syntax: Adit 3500> show interface description Example: Adit 3500> show interface description Device State IP/Mask Dependencies T1 1 running None T1 2 running None T1 3 up None T1 4 up None Serial 1 up 0.0.0.0/255.255.255.255 T1 1 Ethernet 2 disabled 0.0.0.0/0.0.0.0 None Ethernet 1 running 192.168.1.1/255.255.255.0 None IPsec 0 disabled 0.0.0.0/0.0.0.
User Mode show show interface multilink Use the show interface multilink command to display the configuration of the Multilink. Syntax: Adit 3500> show interface multilink port Field Definition port Multilink port number. Range = 1.
User Mode show show interface stats Use the show interface stats command to display the interface statistics.
User Mode show show log Use the show log command to display the current events on the system. Syntax: Adit 3500> show log {firewall|pri|sip|system|t1 port} [severity] Field Definition firewall Filter firewall alarms pri Display PRI logs. Note: This is not supported on the Adit 3104. sip Display SIP logs. system Filter general system alarms t1 port Display T1 event log.
User Mode show show nat-fw Use the show nat-fw command to display the current NAT and firewall connection table. Syntax: Adit 3500> show nat-fw Example: Adit 3500> show nat-fw Number Content 1 TCP 11.0.0.4 36104<--> 172.15.16.1 36104[31.0.0.6 5516 ] TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1320 pkts 7 ppp100 Outgoing BY FTP 2 TCP 11.0.0.4 36103<--> 172.15.16.1 36103[31.0.0.6 21 ] TIME_WAIT/TIME_WAIT ttl 0 sec bytes 1182 pkts 20 FTP child: Yes ppp100 Outgoing 3 TCP 11.0.0.4 36102<--> 172.15.16.1 36102[31.0.0.
User Mode show show port-trigger Use the show port-trigger command to display all port triggering information.
User Mode show show running-config Use the show running-config command to display the current configuration of the system. Syntax: Adit 3500> show running-config Example: Adit 3500> show running-config ip host adit3500 log system notify none log security notify none log t1 notify none . . clock source 1 t1 1 clock source 2 none nat-bypass ip-address 192.168.1.120 mask 255.255.255.0 nat-bypass ip-address 192.168.1.120 mask 255.255.255.
User Mode show no schedule-availability exit interface ethernet 2 . .
User Mode show show service Use the show service command to displays all services.
User Mode show show users Use the show users command to displays all users on this system. Syntax: Adit 3500> show users Example: Adit 3500> show users Provisioned User List User-1 : admin Access: ADMIN
User Mode show show voice-port fxs Use the show voice-port fxs command to display the FXS interface information. Syntax: Adit 3500> show voice-port fxs Example: Adit 3500> show voice-port fxs Registration Address: 192.168.1.
User Mode show show voice-port trunk Use the show voice-port trunk command to display the voice trunk statistics. Note: This command is not supported on the Adit 3104. Syntax: Adit 3500> show voice-port trunk port Field Definition port DS1 (T1) interface.
User Mode traceroute traceroute Use the traceroute command to trace a route to a remote host. Syntax: Adit 3500> traceroute Syntax: Adit 3500> traceroute {address|hostname|stop} Field Definition address IP address of the remote host. hostname Host name of the remote host. stop Stop the traceroute process. Example: Adit 3500> traceroute to 192.168.1.200 (192.168.1.200), 10 hops max 1 192.168.1.200 (192.168.1.200) 10.500 ms 1.013 ms 0.
User Mode traceroute 2-26 Adit 3000 CLI - Release 1.
CHAPTER 3 Privileged Mode The Privileged Mode allows the operator access to the configuration modes of the Adit. This Mode is entered with the Adit 3500> enable command from the Basic mode. The Privileged Mode is represented by the # prompt.
Privileged Mode clear clear clear arp Use the clear arp command to clear the ARP (Address Resolution Protocol) table. Syntax: # clear arp {all|ethernet port|address} Field Definition all Display entire ARP table. ethernet port Display Ethernet ARP items only. port - Define an Ethernet port number. Range 1 - 2. address Enter IP address for specific ARP information on this address.
Privileged Mode configure terminal configure terminal Use the configure terminal command to enter the configuration mode on the Adit 3000s. Syntax: # configure terminal Example: # configure terminal (config)# Supported Platforms: Adit 3104, Adit 3200, Adit 3500 copy copy defaults Use the copy defaults command to restore default setting to the Adit. Syntax: # copy defaults running-config Example: # copy defaults running-config Going to reboot! Restarting system.
Privileged Mode date copy running-config Use the copy running-config command to save the current configuration on the Adit. Note: The TFTP server must be running on the destination device. Syntax: # copy running-config path {destination-path} Field Definition destination-path Enter the destination path, in the form tftp://address/filename to the location where the configuration file is to be saved. address - Enter IP address of the TFTP server. filename - Enter a name for this new configuration file.
Privileged Mode debug debug debug portmon all Use the debug portmon all command allows the user to monitor all traffic of a specific type. All traffic can be displayed, or a specific traffic type can be defined. Note: Immediately after this command is issued, any traffic that falls into the filter parameter will be displayed. To turn the monitoring off, you must issue a no debug portmon command. See no debug portmon command on page 3-17.
Privileged Mode debug Supported Platforms: Adit 3104, Adit 3200, Adit 3500 3-6 Adit 3000 CLI - Release 1.
Privileged Mode debug debug portmon {rx|tx|both} Use the debug portmon {rx|tx|both} command allows the user to monitor specific direction of traffic. Note: Immediately after this command is issued, any traffic that falls into the filter parameter will be displayed. To turn the monitoring off, you must issue a no debug portmon command. See no debug portmon command on page 3-17. Syntax: # debug portmon {rx|tx|both} Field Definition both Display both receive and transmit information.
Privileged Mode debug debug portmon ethernet Use the debug portmon ethernet command allows the user to monitor specific Ethernet traffic. Note: Immediately after this command is issued, any traffic that falls into the filter parameter will be displayed. To turn the monitoring off, you must issue a no debug portmon command. See no debug portmon command on page 3-17.
Privileged Mode debug debug portmon management Use the debug portmon management command allows the user to configure management trace suppression. See no debug portmon command on page 3-17. Syntax: # debug portmon management {hush|off} Field Definition hush hush - Enable suppression of management traffic trace off off - Disable suppression of management traffic trace Example: # debug portmon management hush Supported Platforms: Adit 3104, Adit 3200, Adit 3500 Adit 3000 CLI - Release 1.
Privileged Mode debug debug portmon multilink Use the debug portmon multilink command allows the user to monitor the multilink traffic. All traffic can be displayed, or a specific traffic type can be defined. Note: Immediately after this command is issued, any traffic that falls into the filter parameter will be displayed. To turn the monitoring off, you must issue a no debug portmon command.
Privileged Mode debug debug portmon raw Use the debug portmon raw command allows the user to display raw data related traffic. See no debug portmon command on page 3-17. Syntax: # debug portmon raw {off|on} Field Definition off Disable display of packet hex data on Enables display of packet hex data Example: # debug portmon raw off Supported Platforms: Adit 3104, Adit 3200, Adit 3500 Adit 3000 CLI - Release 1.
Privileged Mode debug debug portmon serial Use the debug portmon serial command allows the user to monitor traffic on a serial port. Note: Immediately after this command is issued, any traffic that falls into the filter parameter will be displayed. To turn the monitoring off, you must issue a no debug portmon command. See no debug portmon command on page 3-17.
Privileged Mode end debug trace Use the debug trace command allows the user to configure trace settings. Note: Immediately after this command is issued, any trace that falls into the filter parameter will be displayed. To turn the monitoring off, you must issue a no debug trace command. See no debug trace command on page 3-17. Syntax: # debug trace {cas|pri|sip} {enable|tx|rx} Field Definition cas Enable Channel Associated Signaling (CAS) tracing. Note: Not supported on the Adit 3104.
Privileged Mode help help Use the help command to display the help information for this command. Note: This can also be accomplished with a ?. Note: This command can be entered in any configuration mode.
Privileged Mode history history Use the history command to display commands that have been entered in this session. Note: This command can be entered in any configuration mode. Syntax: # history Example: # history debug trace sip rx no debug trace no debug trace rx no debug trace sip no debug trace no debug trace sip debug trace date end enable configure terminal history Supported Platforms: Adit 3104, Adit 3200, Adit 3500 Adit 3000 CLI - Release 1.
Privileged Mode log clear log clear Use the log clear command to clear the history of the log. Syntax: # log clear {all|firewall|pri|sip|system|t1} Field Definition all Clear the entire event log. firewall Clear firewall event log. pri Clear PRI event log. Note: Not supported on the Adit 3104. sip Clear SIP event log. system Clear system event log. t1 Clear T1 event log. Example: # log clear firewall Supported Platforms: Adit 3104, Adit 3200, Adit 3500 3-16 Adit 3000 CLI - Release 1.
Privileged Mode no debug no debug no debug portmon Use the no debug portmon command to stop the Packet Monitor (portmon) process. To configure a debug command, see the debug command on page 3-5. Syntax: # no debug portmon Example: # no debug portmon Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no debug trace Use the no debug trace command to stop the trace process. To configure a debug trace, see the debug trace command on page 3-13.
Privileged Mode ping ping Use the ping command to send a sequence of ICMP echo request packets to the specified host. If the host variable is omitted, and you are in Privileged mode, the router prompts you for additional information. Note: The ping command, verifies a connection, and is a very important troubleshooting tool. Syntax: # ping {address [-i time] [-l size] [-n count] [-w timeout]|stop} Field Definition address IP address of the host to ping. -i time Specifies the intervals between pings.
Privileged Mode reload reload Use the reload command to reset the Adit system. CAUTION! THIS IS A SERVICE EFFECTING COMMAND. Syntax: # reload Example: # reload Going to reboot! Restarting system. Supported Platforms: Adit 3104, Adit 3200, Adit 3500 Adit 3000 CLI - Release 1.
Privileged Mode show show For maneuverability through these commands, all command names in blue or italics are hyperlinked.
Privileged Mode show show alarms Use the show alarms command to display the active alarms on the Adit. Syntax: # show alarms [t1 port] {alert|all|critical|info|major|minor} Field Definition t1 port Define a specific port to display alarms. 3104 port range = 1 3500 port range = 1 - 4 alert Filter alert alarms (threshold crossing). all Display all alarms. critical Filter critical alarms. info Filter information alarms. major Filter major alarms (service affecting).
Privileged Mode show show arp Use the show arp command to display the Adit’s ARP (Address Resolution Protocol) table. Syntax: # show arp {all|address|ethernet port} Field Definition all Display entire ARP table. address Display ARP items of the entered IP address. ethernet port Display Ethernet ARP items only. port - Define an Ethernet port number. Range 1 - 2. Example: # show arp ethernet 1 1 192.168.1.1 ether Dynam 00:50:da:59:f0:25 eth_lan Example: # show arp 192.168.1.1 ip=192.168.1.
Privileged Mode show show caclkcd Use the show caclkcd command to display the linux kernel crash dump Syntax: # show caclkcd Example: # show caclkcd ---------------- Begin cacLKCD ----------Jan 1 2003 00:00:44 <3> openrg: unhandled page fault at pc=0x400528c0, lr=0x400 digit-map Show digit-map settings 52890 (bad address=0x30303038, code 245)Show various interfaces pc : [<400528c0>] lr : [<40052890>] No Show l r7 : 4006bb9c r6 : 30303038 r5 : 4006bb9c r4 : 4006bc1c port-trigger r3 : 30303030 r2 : 4006bc1
Privileged Mode show show config access-control Use the show config access-control command to display all access control filters. Syntax: # show config access-control Example: # show config access-control access-control id 1 apply-to lan time-range always service 1 enable Supported Platforms: Adit 3104, Adit 3200, Adit 3500 show config access-list Use the show config access-list command to display all access lists.
Privileged Mode show show config controller Use the show config controller command to display the T1 information. Syntax: # show config controller t1 port Field Definition port T1 port to display.
Privileged Mode show show config dmz-host Use the show config dmz-host command to display the DMZ information. Syntax: # show config dmz-host Example: # show config dmz-host dmz-host 192.168.1.200 enable Supported Platforms: Adit 3104, Adit 3200, Adit 3500 show config host-filter Use the show config host-filter command to display the IP and host name filters. Syntax: # show config host-filter Example: # show config host-filter host-filter id test ip-address 192.168.1.
Privileged Mode show show config interface ethernet Use the show config interface ethernet command to display the Ethernet port information. Syntax: # show config interface ethernet port Field Definition port Ethernet port to display. Range 1 - 2 Example: # show config interface ethernet 1 Interface Ethernet 1 ip address 192.168.1.1 mask 255.255.255.
Privileged Mode show show config interface multilink Use the show config interface multilink command to display the Multilink port information. Syntax: # show config interface multilink port Field Definition port Multilink port to display.
Privileged Mode show show config interface serial Use the show config interface serial command to display the Serial port information. Syntax: # show config interface serial port Field Definition port Serial port to display.
Privileged Mode show show config ip dhcp ethernet Use the show config ip dhcp ethernet command to display the DHCP Pool. Syntax: # show config ip dhcp ethernet port Field Definition port Ethernet port to display. Range 1 - 2 Example: # show config ip dhcp ethernet 1 ip dhcp pool ethernet 1 no relay start-address 192.168.1.1 end-address 192.168.1.244 subnet-mask 255.255.255.
Privileged Mode show show config nat-bypass Use the show config nat-bypass command to display the NAT Bypass entries. Syntax: # show config nat-bypass Example: # show config nat-bypass nat-bypass ip-address 192.168.1.120 mask 255.255.255.0 nat-bypass ip-address 192.168.1.120 mask 255.255.255.0 enable Supported Platforms: Adit 3104, Adit 3200, Adit 3500 show config network-object Use the show config network-object command to display the network object configuration.
Privileged Mode show show config remote-admin Use the show config remote-admin command to display the remote admin configuration.
Privileged Mode show show config service Use the show config service command display the current defined services. Syntax: # show config service Example: # show config service service id 4 name service1 description test protocol tcp server-src-port 1-1 server-dst-port 4-4 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 show config static-dns Use the show config static-dns command to display the static DNS entries.
Privileged Mode show show config voice-port fxs Use the show config voice-port fxs command display the FXS port information. Syntax: # show config voice-port fxs [port] Field Definition port FXS port to display.
Privileged Mode show show config voice-port trunk Use the show config voice-port trunk command display the Trunk port information. Syntax: # show config voice-port trunk port Field Definition port Trunk port to display.
Privileged Mode show show controller t1 Use the show controller t1 command displays the T1 configuration and performance information. Syntax: # show controller t1 port Field Definition port DS1 (T1) interface.
Privileged Mode show show dhcp-leases Use the show dhcp-leases command to display the DHCP lease table. Syntax: Adit 3500> show dhcp-leases Example: Adit 3500> show dhcp-leases Ethernet 1 Hostname : new-host IP:192.168.1.10 MAC:00:00:ff:ff:00:00 Type:static Expires-In:0 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 show digit-map Use the show digit-map command to display the Digit Map patterns.
Privileged Mode show show interface description Use the show interface description command to display the interface information. Syntax: # show interface description Example: # show interface description Device T1 1 T1 2 T1 3 T1 4 Serial 1 Ethernet 2 Ethernet 1 IPsec 0 IPsec 1 State IP/Mask running running up up up 0.0.0.0/255.255.255.255 disabled 0.0.0.0/0.0.0.0 running 192.168.1.1/255.255.255.0 disabled 0.0.0.0/0.0.0.0 running 192.168.1.1/255.255.255.
Privileged Mode show show interface multilink Use the show interface multilink command to display the configuration of the Multilink. Syntax: # show interface multilink port Field Definition port Multilink port number. Range = 1.
Privileged Mode show show ip ospf Use the show ip ospf command to display the general OSPF routing process information. Syntax: # show ip ospf Example: # show ip ospf Routing Process "ospf 0" with ID 192.168.1.
Privileged Mode show show ip ospf database Use the show ip ospf database command to display information related to the OSPF database for a specific router. The various forms of this command deliver information on defined OSPF link state advertisements.
Privileged Mode show Example: # show ip ospf database Router Link States (Area 0.0.0.1) Link ID 192.168.3.1 192.168.3.255 ADV Router 192.168.3.1 192.168.3.255 Age Seq# CkSum Link count 313 0x800000c1 0x4978 1 568 0x8000003a 0xa6c0 1 Net Link States (Area 0.0.0.1) Link ID 192.168.3.251 ADV Router 192.168.3.255 Age Seq# CkSum 388 0x80000003 0xbcec Example: #show ip ospf database self-originate Router Link States (Area 0.0.0.1) Link ID ADV Router Age Seq# CkSum Link count 192.168.3.255 192.168.3.
Privileged Mode show show ip ospf interface Use the show ip ospf interface command to display OSPF related interface information. Syntax: # show ip ospf interface {ethernet port|serial port|multilink port} Field Definition ethernet port Display information on the Ethernet interface. port = 1 or 2 serial port Display information on the Serial interface. port = 1 multilink port Display information on the Multilink interface.
Privileged Mode show show ip ospf neighbor Use the show ip ospf neighbor command to display OSPF neighbor information. Syntax: # show ip ospf neighbor [interface address|neighbor-id|detail] Field Definition interface address Optional parameter. Enter interface IP address to define display. neighbor-id Optional parameter. Enter neighbor IP address to define display. detail Optional parameter. Enable display of detailed information. Example: # show ip ospf neighbor ID Pri 10.199.199.137 1 172.16.
Privileged Mode show show ipsec Use the show ipsec command to display the IPSec Connections or the connection configuration information. Syntax: # show ipsec [spn_ipsecconnection-id] Field Definition connection-id Enter the name of a connection. Example: # show ipsec vpn_ipsec vpn_ipsec vpn_ipsec vpn_ipsec 0 1 2 3 Example: # show ipsec vpn_ipsec2 Device = test State = Enabled tatus = No VPN software license Schedule Availability = Always Remote Tunnel Endpoint Address = 192.168.1.
Privileged Mode show show l2tpc Use the show l2tpc command to display the Layer 2 Tunneling Protocol Connections or the connection configuration information. Syntax: # show l2tpc [l2tpc connection-id] Field Definition connection-id Enter the name of a connection.
Privileged Mode show show licenses Use the show licenses command to display all feature keys enabled on the Adit. Syntax: # show licenses Example: # show licenses VPN SIP MGCP G729A license license license license = = = = No Yes No Yes Supported Platforms: Adit 3104, Adit 3200, Adit 3500 show log Use the show log command to display the current events on the system.
Privileged Mode show show mac-address-table Use the show mac-address-table command to display the current MAC addresses (LAN\WAN). Syntax: # show mac-address-table Example: # show mac-address-table Ethernet 1 mac= 00:00:00:ff:ff:ff Ethernet 2 mac= 00:00:00:ff:ff:fd Supported Platforms: Adit 3104, Adit 3200, Adit 3500 show nat-fw Use the show nat-fw command to display the current NAT and firewall connection table. Syntax: # show nat-fw Example: # show nat-fw Number Content 1 TCP 11.0.0.
Privileged Mode show show port-trigger Use the show port-trigger command to display the port trigger information. Syntax: # show port-trigger Example: # show port-trigger Service ID:134217730 Trigger protocol: UDP dst_end=1701 Enable Service Name:L2TP port: src_start=0 src_end=0 Service ID:16777223 Trigger protocol: UDP dst_end=69 Enable Service Name:TFTP port: src_start=1024 src_end=65535 dst_start=1701 dst_start=69 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 Adit 3000 CLI - Release 1.
Privileged Mode show show pptpc Use the show pptps command to display the PPTP connections or the PPTP connection details. Syntax: # show pptpc [pptpc connection-id] Field Definition connection-id Enter the name of a connection.
Privileged Mode show show pptps Use the show pptps command to display the PPTP Server settings. Syntax: # show pptps Example: # show pptps state = Enable status = Invalid vpn license Idle_Time = 1200 Authentication = MS-CHAP MS-CHAPv2 PAP Encryption = MPPE-40 MPPE-128 (Stateless) Remote IP Address Range = 192.168.1.245 - 192.168.1.254 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 show route Use the show route command to display the routing table.
Privileged Mode show show running-config Use the show running-config command to display the current configuration of the system. Syntax: # show running-config Example: # show running-config ip host adit3500 log system notify none log security notify none log t1 notify none clock source 1 t1 1 clock source 2 none controller t1 1 description T1 #1 lbo short 133 fdl none framing esf linecode b8zs loopdetect none loopback none idle-pattern 0x7f no pri-group no tdm-group no ds0-group . .
Privileged Mode show connection t1 2 no echo-cancel input-gain 0 output-gain 0 isdn switch-type primary-ni2 voice-port fxs 1 description Line 1 no comfort-noise echo-cancel enable input-gain 0 output-gain 0 dial-timeout 5 signal loop-start . .
Privileged Mode show show service Use the show service command to display all service information. Note: The following example, is only a portion of the list. Syntax: # show service Example: # show service Group: Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger Service Trigger . . .
Privileged Mode show show users Use the show users command to display all users on this system. Syntax: # show users Example: # show users Provisioned User List User-1 : admin Access: ADMIN
Privileged Mode show show voice-port fxs Use the show voice-port fxs command to display the FXS voice port information. Syntax: # show voice-port fxs Example: # show voice-port fxs Registration Address: 192.168.1.
Privileged Mode show show voice-port trunk Use the show voice-port trunk command to display the trunk voice port information. Syntax: # show voice-port trunk port Field Definition port DS1 (T1) interface. Range 1.
Privileged Mode traceroute traceroute Use the traceroute command to trace a route to a remote host. Syntax: Adit 3500> traceroute Syntax: Adit 3500> traceroute {address|hostname|stop} Field Definition address IP address of the remote host. hostname Host name of the remote host. stop Stop the traceroute process. Example: Adit 3500> traceroute to 192.168.1.200 (192.168.1.200), 10 hops max 1 192.168.1.200 (192.168.1.200) 10.500 ms 1.013 ms 0.
CHAPTER 4 Global Configuration Mode The Global Configuration Mode allows commands to be entered directly the router configuration. From this level, additional configuration modes can be entered. Once configuration is complete, use exit/end command to return to the Privileged prompt. Note: The Trunk option is not available on the Adit 3104. This Mode is entered with the # configure terminal command from the Privileged mode The Global Configuration Mode is represented by the (config)# prompt.
Global Configuration Mode Commands to Configuration Sub-Commands Commands to Configuration Sub-Commands 4-2 Configuration Mode Link to Command Prompt Displayed Controller T1 controller t1 (config-cont-t1-{n})# DHCP server pool ip dhcp pool ethernet (config-dhcp-eth-{n})# Dial Peer FXS dial-peer voice pots fxs (config-dpeer-fxs)# Dial Peer Trunk dial-peer voice pots trunk (config-dpeer-trk)# Dial Peer VoIP dial-peer voice voip (config-dpeer-voip)# Ethernet Interface interface ethernet
Global Configuration Mode access Global Configure Commands access Use the access command to enable remote access via LAN or WAN. To disable remote access, see no access command on page 4-33. Syntax: (config)# access {lan|wan} enable Field Definition lan Enable remote access via the LAN. wan Enable remote access via the WAN.
Global Configuration Mode access-list access-list Use the access-list command to configure the advanced filtering entries. To delete an access list, see no access-list command on page 4-34.
Global Configuration Mode authentication login authentication login Use the authentication login command to use RADIUS for login authentication. To remove an authentication login, see no authentication login command on page 4-34. Syntax: (config)# authentication login use-radius Example: (config)# authentication login use-radius Supported Platforms: Adit 3104, Adit 3200, Adit 3500 clock source Use the clock source command to define the primary and secondary clock source.
Global Configuration Mode date date date Use the date command to display the Adit’s current date. Syntax: (config)# date Example: (config)# date Mon May 1 05:33:57 2006 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 date auto-time-update Use the date auto-time-update command to automatically update the clock from the defined server. To stop the auto update, see no date auto-time-update command on page 4-34.
Global Configuration Mode date date set Use the date set command to manually set the Adit’s internal clock. Syntax: (config)# date set hh:mm:ss dd mm yyyy Field Definition hh:mm:ss Set the time in the 24 hour format hh:mm:ss hh = hours, range is 0 - 23 mm = minutes, range is 0 - 59 ss = seconds, range is 0 - 59 dd dd = day, range is 1 - 31 mm mm = month, range is 1 - 12 yyyy Enter current year (example 2006). Range 1970 - 2037.
Global Configuration Mode delete local-server date timezone Use the date timezone command to set the Adit’s time zone and the number of hours from the GMT. Syntax: (config)# date timezone hh:mm Field Definition hh Hour offset from GMT. Range is from -12 to +12, with a default of 0. mm Minute offset from GMT in minutes. Range is from 00 to 59, with a default of 00. This is used for half hour time zones.
Global Configuration Mode dial-peer voice dial-peer voice dial-peer voice pots fxs Use the dial-peer voice pots fxs command to allow access to the Dial Peer Voice FXS configuration commands. See Chapter 7, Configuration - Dial Peer FXS Mode for commands in this mode. For the no counterpart of this command see no dial-peer voice pots fxs command on page 4-35. Syntax: (config)# dial-peer voice pots fxs port Field Definition port Selects the port to configure. Adit 3104 FXS - Range is 1-24.
Global Configuration Mode dmz-host dial-peer voice voip Use the dial-peer voice voip command to allow access to the Dial Peer Voice VoIP configuration commands. See Chapter 9, Configuration - Dial Peer VoIP Mode for commands in this mode. For the no counterpart of this command see no dial-peer voice voip command on page 4-36. Syntax: (config)# dial-peer voice voip trunk Field Definition trunk Enter trunk number. Range is 1-50.
Global Configuration Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Global Configuration Mode dynamic-dns dynamic-dns Use the dynamic-dns commands to configure the DNS Dynamic entries. To disable Dynamic DNS, see no dynamic-dns command on page 4-36. dynamic-dns backup-mx Use the dynamic-dns backup-mx command to enable the Dynamic DNS backup MX.
Global Configuration Mode dynamic-dns dynamic-dns offline Use the dynamic-dns offline command to enable Dynamic DNS offline. Syntax: (config)# dynamic-dns offline enable Example: (config)# dynamic-dns offline enable Supported Platforms: Adit 3104, Adit 3200, Adit 3500 dynamic-dns username Use the dynamic-dns username command to define the Dynamic DNS username. Syntax: (config)# dynamic-dns username username Field Definition username Enter your Dyndns user name.
Global Configuration Mode end end Use the end command to exit the current configuration mode. Note: This command can be entered in any configuration mode with the same result. Syntax: (config)# end Example: (config)# end # Supported Platforms: Adit 3104, Adit 3200, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Global Configuration Mode help help Use the help command to display the help information for this command. Note: This can also be accomplished with a ?. Note: This command can be entered in any configuration mode.
Global Configuration Mode history history Use the history command to display commands that have been entered in this session. Note: This command can be entered in any configuration mode. Syntax: (config)# history Example: (config)# history clock source 1 none controller t1 1 date date set 12:12:06 15 12 2006 date set 3:4:3 date set 12:12:20 date set 0:0:1 date summer-time 3 28 00:00 10 28 01:00 60 date timezone +03:00 dial-peer voice pots trunk 1 1 dial-peer voice voip dmz-host 192.168.1.
Global Configuration Mode host-filter host-filter Use the host-filter command to configure the IP/host name filtering entries. To delete a host filter, see no host-filter command on page 4-37. Syntax: (config)# host-filter id filter-id {ip-address address|hostname hostname} apply-to {lan|network-object object-id} time-range {always|schedule-id} Field Definition filter-id Enter a filter ID name. address Enter the host IP address. hostname Enter a host name for the rule.
Global Configuration Mode interface multilink interface multilink Use the interface multilink command to allow access to the MLPPP configuration commands. See Chapter 11, Configuration - Multilink Interface Mode for commands in this mode. To delete a Multilink interface, see no interface multilink command on page 4-39. Syntax: (config)# interface multilink group-number Field Definition group-number Enter current multilink group number. Range = 1. Note: Currently only 1 multilink port is supported.
Global Configuration Mode ipsec ipsec Use the ipsec commands to create an IPSec connection and to configure IPSec global settings. See Chapter 13, Configuration - IPSec Mode for additional commands in this mode. ipsec authentication-retries Use the ipsec authentication-retries command to enable the block-ip feature. To disable block-ip, see no ipsec authentication-retries command on page 4-37.
Global Configuration Mode ipsec ipsec log ike Use the ipsec log ike command to enable Internet Key Exchange (IKE) related logs. To disable IKE logging, see no ipsec log ike command on page 4-37 Syntax: (config)# ipsec log ike {auto-key|ike-int|ike-msg|msg-byte| msg-enc-dec|msg_inp|msg-outp|pri-key|rej-packet} Field Definition auto-key Enable verbose automatic keying. ike-int Enable verbose IKE IPSec interaction. ike-msg Print all IKE message ignoring rate limit.
Global Configuration Mode ipsec ipsec log ipsec Use the ipsec log ipsec command to enable IPSec related logs. To disable IPSec logging, see no ipsec log ipsec command on page 4-38. Syntax: (config)# ipsec log ipsec {atc|emvc|etc|ip-ctc|irtmc|mirl |rc|rtmc|satmc|tc|tsmc|ttc|usc|vrp} Field Definition atc Authentication Transforms Code. emvc Even More Verbose Output. etc Encryption Transforms Code. ip-ctc IP Compression Transforms Code. irtmc Internal Route Table Manipulation Code.
Global Configuration Mode ipsec ipsec net-to-net Use the ipsec net-to-net command to create a network-to-network connection. Syntax: (config)# ipsec net-to-net remote-ip {address|any} remote-subnet {ip address mask mask|any} pre-share secret Field Definition remote-ip address - Enter the remote tunnel endpoint address. any - Allow any IP address. remote-subnet address - Enter an IP address if it is a remote IP. mask - Enter an IP mask if it is a remote IP. any - Allow any IP address.
Global Configuration Mode ip dhcp pool ethernet ip dhcp pool ethernet Use the ip dhcp pool ethernet command to allow access to the DHCP configuration commands. See Chapter 6, Configuration - DHCP Pool Ethernet Mode for commands in this mode. For the no counterpart, see no ip dhcp pool ethernet command on page 4-40. Syntax: (config)# ip dhcp pool ethernet port Field Definition port Selects the Ethernet port to configure. Range is 1-2.
Global Configuration Mode key key Use the key command to enable a specific keyed feature. To acquire a feature key code, contact Carrier Access Customer Support. Syntax: (config)# key key-code Field Definition key-code The key code is entered to enable the specific feature. Example: (config)# key q0B8yma2IsSL+1BarY0u Supported Platforms: Adit 3104, Adit 3200, Adit 3500 l2tpc Use the l2tpc command to allow access to the VPN L2TP Connection configuration commands.
Global Configuration Mode local-server local-server Use the local-server command to configure the local server entries. To delete a local server, see no local-server command on page 4-40. Syntax: (config)# local-server id {name|new} {ip-address address |hostname hostname} time-range {always|schedule-name} fwd-port port service service-id Field Definition name Enter a name of the server. new Select New to create a new local server. address Enter an IP address of the local server.
Global Configuration Mode log log log pri Use the log pri command to configure PRI logging. Syntax: (config)# log pri {buffer-fill {0|1}|buffer-size kilobytes |display number|enable} Field Definition buffer-fill {0|1} Define the method of loading the buffer. 0 = Circular Buffer - the buffer will store a continuous stream of data by starting again at the beginning of the buffer after reaching the end. Default. 1 = Fill Until Full - the buffer will fill until it is full.
Global Configuration Mode log log security notify Use the log security notify command to set the remote security notify level. Syntax: (config)# log security notify {error|info|ip-address address |none|warn} Field Definition error Notify for error level. info Notify for information level. ip-address address Enter IP address of remote system to notify. none No notification. warn Notify for warning level.
Global Configuration Mode log log system buffer Use the log system buffer command to set the buffer size allowed for the system log buffer. Syntax: (config)# log system buffer kilobytes Field Definition kilobytes Set the size of the system log buffer. Range is 1 - 256 KB. Default is 16KB. Example: (config)# log system buffer 24 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 log system notify Use the log system notify command to set the remote system notify level.
Global Configuration Mode log log t1 buffer Use the log t1 buffer command to set the buffer size allowed for the T1 log buffer. Syntax: (config)# log t1 buffer kilobytes Field Definition kilobytes Set the size of the T1 log buffer. Range is 1 - 256 KB. Default is 16KB. Example: (config)# log t1 buffer 24 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 log t1 notify Use the log t1 notify command to set the remote T1 notify level.
Global Configuration Mode mail-server mail-server mail-server authentication enable Use the mail-server authentication enable command to enable the outgoing mail server authentication. To disable the mail-server authentication, see no mail-server authentication command on page 4-41.
Global Configuration Mode mail-server mail-server port Use the mail-server port command to set the outgoing mail server port. Syntax: (config)# mail-server port port Field Definition port Enter the port number. Range is 0 - 65535. Default is 25. Example: (config)# mail-server port 25 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 mail-server username Use the mail-server username command to set the username and password for the mail server.
Global Configuration Mode nat-bypass nat-bypass Use the nat-bypass command to create and enable a NAT bypass rule. To disable NAT Bypass, see no nat-bypass command on page 4-41. Syntax: (config)# nat-bypass ip-address address mask mask [enable] Field Definition address Enter a NAT bypass IP address. mask Enter a subnet mask for the above address. enable Enable NAT bypass. Note to create the rule, without enabling, do not enter this option. Example: (config)# nat-bypass ip-address 10.10.2.
Global Configuration Mode no commands no commands no access Use the access command to disable remote access via LAN or WAN. To enable remote access, see access command on page 4-3. Syntax: (config)# no access {lan|wan} Field Definition lan Disable access to the unit via the LAN. wan Disable access to the unit via the WAN. Example: (config)# no access lan Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no access-control Use the no access-control command to remove an access rule for the system.
Global Configuration Mode no commands no access-list Use the no access-list command to remove an advanced filtering entry. To add a filter, see accesslist command on page 4-4. Syntax: (config)# no access-list rule rule-name apply {eth-lan|eth-wan |ppp-wan|initial|final} Field Definition rule-name Enter an existing rule name to apply this command to. eth-lan Ethernet LAN interface. eth-wan Ethernet WAN interface. initial Initial rules defined here will be applied first to the interface.
Global Configuration Mode no commands no date summer-time Use the no date summer-time command to remove daylight savings time setting. To enable daylight savings, see date summer-time command on page 4-7. Syntax: (config)# no date summer-time Example: (config)# no date summer-time Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no dial-peer voice pots fxs Use the no dial-peer voice pots fxs command denies access to the Dial Peer Voice POTS FXS configuration commands.
Global Configuration Mode no commands no dial-peer voice voip Use the no dial-peer voice voip command denies access to the Dial Peer Voice VoIP configuration commands. To allow access, see dial-peer voice command on page 4-9. Syntax: (config)# no dial-peer voice voip tag Field Definition tag Enter the tag number to denies access. Range is 1-30. Example: (config)# no dial-peer voice voip 1 Supported Platforms: Adit 3104, Adit 3500 no dmz-host Use the no dmz-host command to remove a DMZ host.
Global Configuration Mode no commands no host-filter Use the no host-filter command to remove a IP host name filter entry. To add a IP host name, see host-filter command on page 4-17. Syntax: (config)# no host-filter name Field Definition name Name of an existing IP host name to remove. Example: (config)# no host-filter HostFilter1 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ipsec authentication-retries Use the no ipsec authentication-retries command to disable the block-ip feature.
Global Configuration Mode no commands no ipsec log ipsec Use the no ipsec log ipsec command to disable IPSec related logs. To enable IPSec logging, see ipsec log ipsec command on page 4-21 Syntax: (config)# no ipsec log ipsec {atc|emvc|etc|ip-ctc|irtmc|mirl |rc|rtmc|satmc|tc|tsmc|ttc|usc|vrp} Field Definition atc Authentication Transforms Code. emvc Even More Verbose Output. etc Encryption Transforms Code. ip-ctc IP Compression Transforms Code. irtmc Internal Route Table Manipulation Code.
Global Configuration Mode no commands no ipsec vpn_ipsec Use the no ipsec vpn_ipsec command to delete an IPSec connection. To create an IPSec connection, see ipsec net-to-host command on page 4-21 or ipsec net-to-net command on page 4-22 To enter an IPSec connection, for configuration see ipsec vpn_ipsec command on page 4-22. Syntax: (config)# no ipsec ipsec connection-id Field Definition connection-id Enter the name of a connection.
Global Configuration Mode no commands no ip dhcp pool ethernet Use the DHCP Pool no ip dhcp pool ethernet command to disable the DHCP server for the interface defined. To enter the DHCP configuration mode, see ip dhcp pool ethernet command on page 4-23. Syntax: (config)# no ip dhcp pool ethernet port Field Definition port Ethernet port number. Range is 1 or 2.
Global Configuration Mode no commands no log sip Use the no log sip command to stop SIP logging. To enable SIP logging, see log sip command on page 4-27. Syntax: (config)# no log sip Example: (config)# no log sip Supported Platforms: Adit 3104, Adit 3500 no mail-server authentication Use the no mail-server authentication command to disable the outgoing mail server authentication. To enable the mail server, see mail-server command on page 4-30.
Global Configuration Mode no commands no network-object Use the no network-object command to remove network objects. To enable a network object, see network-object command on page 4-32. Syntax: (config)# no network-object name type {ip-address address| mac-address address|hostname hostname} Field Definition name Enter name for the Network Object. Maximum of 60 characters. hostname Enter the host name of the Network Object. address Enter the IP address of the Network Element.
Global Configuration Mode no commands no pptps Use the no pptps command to disable the VPN PPTP server. To enter the VPN PPTPS configuration mode, see the pptps command on page 4-50. Syntax: (config)# no pptps Example: (config)# no pptps Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no radius-client Use the no radius-client command disables the RADIUS configuration. To enter the RADIUS configuration mode, see radius-client command on page 4-51.
Global Configuration Mode no commands no remote-admin telnet Use the no remote-admin telnet command to remove remote administration to the Adit via Telnet. To enable remote access via telnet, see remote-admin telnet command on page 4-52.
Global Configuration Mode no commands no remote-admin web Use the no remote-admin web command to remove remote administration to the Adit via Web-management. To enable remote access via the web, see remote-admin web command on page 4-53.
Global Configuration Mode no commands no security-log Use the no security-log command to remove a security policy. To add a security policy, see security-log command on page 4-55. Syntax: (config)# no security-log setting Field Definition setting Accepted Events accepted-in-connects Blocked Events Other Events Log Buffer Disable incoming connections logging. accepted-out-connects Disable outgoing connections logging. block-conn-attempts Disable block connection attempts logging.
Global Configuration Mode no commands no service Use the no service command to disable named services. To enable services, see service command on page 4-56. Syntax: (config)# no service service-id Field Definition service-id Enter the service number to apply the rule to.
Global Configuration Mode no commands no static-dns Use the no static-dns command to remove DNS Static entries. To add a DNS static entry, see staticdns command on page 4-58. Syntax: (config)# no static-dns hostname hostname ip-address address Field Definition hostname Enter a DNS static host name of the server. address Enter the DNS static IP address. Example: (config)# no static-dns hostname server1 ip-address 192.168.100.
Global Configuration Mode no commands no vlan Use the no vlan command to clear all VLANs. To enter the VLAN configuration mode, see vlan (global) command on page 4-60. Syntax: (config)# no vlan Example: (config)# no vlan Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no voice-codec Use the no voice-codec command to remove a voice codec. To set the voice codecs, see voice-codec command on page 4-61. Syntax: (config)# no voice-codec {g711alaw|g711ulaw|g729} Field Definition g711alaw G.
Global Configuration Mode port-trigger service port-trigger service Use the port-trigger service command to configure the port-triggering entries. To delete a port trigger service, see no port-trigger-service command on page 4-42. Syntax: (config)# port-trigger service name enable Field Definition name Enter service name.
Global Configuration Mode radius-client radius-client Use the radius-client command to allow access to the RADIUS configuration commands. See Chapter 18, Configuration - RADIUS Mode for commands in this mode. For the no counterpart of this command, see no radius-client command on page 4-43.
Global Configuration Mode remote-admin remote-admin telnet Use the remote-admin telnet command to allow remote administration to the Adit via Telnet. To deny telnet remote access, see no remote-admin telnet command on page 4-44. CAUTION! Syntax: ALLOWING REMOTE ADMINISTRATION TO THE ADIT IS A SECURITY RISK.
Global Configuration Mode router ospf remote-admin web Use the remote-admin web command to allow remote administration to the Adit via Webmanagement. To deny Web remote access, see no remote-admin web command on page 4-45. CAUTION! Syntax: ALLOWING REMOTE ADMINISTRATION TO THE ADIT IS A SECURITY RISK.
Global Configuration Mode security-default security-default Use the security-default command to configure the security policy. Syntax: (config)# security-default {maximum|minimum|typical} [block-ip-frag] Field Definition The following security levels are described in detail. Requests Originating in the WAN Requests Originating in the LAN maximum Blocked: No access to network from Internet, except as configured in the Local Servers, DMZ host and Remote Access screens.
Global Configuration Mode security-log security-log Use the security-log command to configure the security policy. To delete a security policy, see no security-log command on page 4-46. Syntax: (config)# security-log setting enable Field Definition Accepted Events accepted-in-connections Sessions originated from the Internet that have been allowed by the firewall. accepted-outconnections Sessions originated from the network that have been allowed by the firewall.
Global Configuration Mode service service Use the service command to create/modify User-Defined Services on the Adit. To delete a service policy, see no service command on page 4-47. Syntax: (config)# service id {service-id|new} name service-name description text protocol {protocol-number|ah|esp|gre|icmp|tcp |udp} [server-src-port|open-src-port] Field Definition service-id Enter a User-Defined Service number to modify.
Global Configuration Mode snmp-server snmp-server The following are the commands to set the SNMP server configuration. To delete a SNMP server, see no snmp-server command on page 4-47. snmp-server community Use the snmp-server community command to set the SNMP community name. Syntax: (config)# snmp-server community community-name {ro|rw} Field Definition community-name Enter the SNMP Community Name. ro Read only - Set the community name to read only permission.
Global Configuration Mode static-dns snmp-server traps enable Use the snmp-server traps enable command to enable SNMP traps on the system. To delete a SNMP server trap, see no snmp-server traps command on page 4-47.
Global Configuration Mode time-range time-range Use the time-range command to define availability of the Ethernet port. To delete a time range, see no time-range command on page 4-48. Syntax: (config)# time-range id schedule-id name schedule-name {active|inactive} time-segment time-segment-id {mon|tue|wed|thu|fri|sat|sun} time-range hh:mm-hh:mm Field Definition schedule-id Enter a schedule ID for the scheduler rule. schedule-name Enter a name for the scheduler rule.
Global Configuration Mode vlan (global) vlan (global) Use the vlan command to allow access to the global VLAN configuration commands. See Chapter 19, Configuration - VLAN Mode for commands in this mode. To clear VLANs, see the no vlan command on page 4-49. Syntax: (config)# vlan Example: (config)# vlan (config-vlan)# Supported Platforms: Adit 3104, Adit 3200, Adit 3500 vlan (vlan-id) Use the vlan command to allow access to the VLAN port configuration commands.
Global Configuration Mode voice-codec voice-codec Use the voice-codec command to select which codecs are to be enabled and allows the user to set the Packetization Time for that codec. To disable a codec, see no voice-codec command on page 4-49. Syntax: (config)# voice-codec {g711alaw|g711ulaw|g729} ptime {10|20|30|40|50|60|70|80} Field Definition g711alaw G.711, 64kbps, A-law g711ulaw G.711, 64kbps, μ-law g729 G.729, 8kbps ptime Set the Packetization Time for the codec. Default for all is 20.
Global Configuration Mode voice-port fxs voice-port fxs Use the voice-port fxs command to allow access to the Voice Port FXS configuration commands. See Chapter 22, Configuration - Voice Port FXS Mode for commands in this mode. Syntax: (config)# voice-port fxs port Field Definition port FXS voice port number. Range is 1.
CHAPTER 5 Configuration - T1 Controller Mode The T1 Controller Configuration commands allow the user to configure the Controller parameters. This sub-group is entered with the (config)# controller t1 command from the Configure mode. The T1 Controller commands are represented by the (config-cont-t1-{n})# prompt.
Configuration - T1 Controller Mode description description Use the Controller T1 description command to set the circuit ID of the T1. Syntax: (config-cont-t1-{n})# description text Field Definition text Enter a description for the Controller T1. Example: (config-cont-t1-1)# description T1#1 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 5-2 Adit 3000 CLI - Release 1.
Configuration - T1 Controller Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - T1 Controller Mode ds0-group ds0-group Use the Controller T1 ds0-group command to create a group of T1s. To delete a DS0 group, see no ds0-group command on page 5-9. Syntax: (config-cont-t1-{n})# ds0-group timeslots range Field Definition range DS0 timeslot range, in the format n-n (1-4). Range is 1 - 24.
Configuration - T1 Controller Mode fdl fdl Use the Controller T1 fdl command to set line Facilities Data Link (FDL) capabilities the T1 interface. Syntax: (config-cont-t1-{n})# fdl {none|t1.403} Field Definition none Disable FDL output messages. Default. t1.403 Enable T1.403 FDL performance messages. Example: (config-cont-t1-1)# fdl none Supported Platforms: Adit 3104, Adit 3200, Adit 3500 framing Use the Controller T1 framing command to set the framing option for the designated T1.
Configuration - T1 Controller Mode history history Use the history command to display commands that have been entered in this session. Note: This command can be entered in any configuration mode.
Configuration - T1 Controller Mode lbo lbo lbo long Use the Controller T1 lbo long command to set Line Build Out on the T1. Syntax: (config-cont-t1-{n})# lbo long {-7.5db|-15db|-22.5db} Field Definition -7.5db CSU attenuation for LBO of 7.5dB -15db CSU attenuation for LBO of 15dB -22.5db CSU attenuation for LBO of 22.
Configuration - T1 Controller Mode linecode linecode Use the Controller T1 linecode command to set the line coding for the designated T1. Syntax: (config-cont-t1-{n})# linecode {ami|b8zs} Field Definition ami Alternate Mark Inversion line coding (AMI). b8zs Binary 8 Zero Substitution line coding (B8ZS). Default. Example: (config-cont-t1-1)# linecode ami Supported Platforms: Adit 3104, Adit 3200, Adit 3500 loopback Use the Controller T1 loopback command enables a loopback on the T1.
Configuration - T1 Controller Mode loopdetect loopdetect Use the Controller T1 loopdetect command to enable the detection of CSU or NIU loop code. Syntax: (config-cont-t1-{n})# loopdetect {csu|niu|none} Field Definition csu Enable detection of CSU loop codes (10000 for loop up, 100 for loop down) niu Enable detection of NIU loop codes none Disable detection. Default.
Configuration - T1 Controller Mode pri-group no shutdown Use the Controller T1 no shutdown command to set the T1 up (In-Service). To set the T1 down (Out-of-Service), see shutdown command on page 5-11. Syntax: (config-cont-t1-{n})# no shutdown Example: (config-cont-t1-1)# no shutdown Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no tdm-group Use the Controller T1 no dm-group command to ungroup TDM timeslots. To group TDM timeslots, see tdm-group command on page 5-11.
Configuration - T1 Controller Mode shutdown shutdown Use the Controller T1 shutdown command to set the T1 interface down (out-of-service). To set the T1 up (in-service) see no shutdown command on page 5-10. Syntax: (config-cont-t1-{n})# shutdown Example: (config-cont-t1-1)# shutdown Supported Platforms: Adit 3104, Adit 3200, Adit 3500 tdm-group Use the Controller T1 tdm-group command to create a group and define its direction. To delete a TDM group, see no tdm-group command on page 5-10.
Configuration - T1 Controller Mode threshold threshold Use the Controller T1 threshold command to define the interval and threshold levels for this T1. Syntax: (config-cont-t1-{n})# threshold {daily|min15} {bes|css|dm|es|lcv|les|pcv|sefs|ses|uas} {value} Threshold Settings Minute 15 Daily BES - Bursty Errored Seconds Default is 0. Defect Threshold Range is 0 - 900 Default is 0. Range is 0 - 86400 CSS - Controller Slip Seconds Defect Threshold Default is 0. Range is 0 - 900 Default is 0.
CHAPTER 6 Configuration - DHCP Pool Ethernet Mode The DHCP Pool Configuration commands allow the user to configure the DHCP parameters for each interface. This sub-group is entered with the (config)# ip dhcp pool ethernet command from the Configure mode. The DHCP Pool commands are represented by the (config-dhcp-eth-{n})# prompt.
Configuration - DHCP Pool Ethernet Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - DHCP Pool Ethernet Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. NOTE: This command can be entered in any configuration mode with the same result. Syntax: (config-dhcp-eth-{n})# end Example: (config-dhcp-eth-1)# end # Supported Platforms: Adit 3104, Adit 3200, Adit 3500 end-address Use the DHCP end-address command to define the DHCP end address.
Configuration - DHCP Pool Ethernet Mode history history Use the history command to display commands that have been entered in this session. NOTE: This command can be entered in any configuration mode. Syntax: (config-dhcp-eth-{n})# history Example: (config-dhcp-eth-1)# history end-address 192.168.1.250 lease 900 relay 192.168.1.120 start-address 192.168.1.1 subnet-mask 255.255.255.
Configuration - DHCP Pool Ethernet Mode no commands no commands no option Use the DHCP Pool no option command to delete a DHCP option. To add a DHCP pool, see option command on page 6-6. Syntax: (config-dhcp-eth-{n})# no option {66|67} Field Definition 66 Remove/Disable option 66 (TFTP server name). 67 Remove/Disable option 67 (Boot file name).
Configuration - DHCP Pool Ethernet Mode option option Use the option command to configure the DHCP options on the Adit, as per RFC 2132. To delete an option, see no option command on page 6-5. Syntax: (config-dhcp-eth-{n})# option {66 {enable|value {address|hostname}|67 {enable|value filename} Field Definition 66 66 - Send the TFTP server name. address - Enter the IP address of the TFTP server. hostname - Enter the host name of the TFTP server. 67 67 - Send the Boot file name.
Configuration - DHCP Pool Ethernet Mode start-address start-address Use the DHCP Pool start-address command to define the DHCP start IP address. This command works with the end-address (end IP address) to define the number of IP addresses in the DHCP pool. Which also limits the number of hosts that may be connected to the network in this subnet. Start defines the first IP address that may be assigned in this subnet.
Configuration - DHCP Pool Ethernet Mode subnet-mask subnet-mask Use the DHCP Pool subnet-mask command to define the subnet mask for the DHCP pool. Syntax: (config-dhcp-eth-{n})# subnet-mask mask Field Definition mask Enter the DHCP pool subnet mask, using the form xxx.xxx.xxx.xxx, where xxx is a number from 0 to 255. This is an optional setting. Example: (config-dhcp-eth-1)# subnet-mask 255.255.255.
CHAPTER 7 Configuration - Dial Peer FXS Mode The Dial Peer FXS Configuration commands allow the user to configure the Dial Peer FXS parameters. Enter this sub-group with the (config)# dial-peer voice pots fxs port command from the Configure mode. The Dial Peer FXS commands are represented by the (config-dpeer-fxs)# prompt.
Configuration - Dial Peer FXS Mode block-out-caller-id block-out-caller-id Use the Dial Peer block-out-caller-id command to enable the blocking of outgoing Caller ID. To disable blocking, see no block-out-caller-id command on page 7-8. Syntax: (config-dpeer-fxs)# block-out-caller-id enable Example: (config-dpeer-fxs)# block-out-caller-id enable Supported Platforms: Adit 3104, Adit 3500 call-wait-caller-id Use the Dial Peer call-wait-caller-id command to enable Call Waiting and Caller ID.
Configuration - Dial Peer FXS Mode codec preference codec preference Use the Dial Peer codec preference command to set the codec preferences used to establish the codec list offered during media negotiation. To delete a codec, see no codec preference command on page 7-9. Syntax: (config-dpeer-fxs)# codec preference {1|2|3} {g711alaw| g711ulaw|g729} Field Definition 1|2|3 Enter the preference number. #1 being the first preference. g711alaw Set the codec preference to G.711 A-law.
Configuration - Dial Peer FXS Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - Dial Peer FXS Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Syntax: (config-dpeer-fxs}# end Example: (config-dpeer-fxs)# end # Supported Platforms: Adit 3104, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - Dial Peer FXS Mode fax-protocol fax-protocol Use the Dial Peer fax-protocol command to configure the fax protocol. Syntax: (config-dpeer-fxs)# fax-protocol {none|pass-through|t38| t38_reserved} Field Definition none A Fax call would be treated as a normal voice call. Default. pass-through Will cause the line to transmit in G.711 mode, with echo cancellation and silence suppression disabled, on detection of Fax tone.
Configuration - Dial Peer FXS Mode modem-protocol modem-protocol Use the Dial Peer modem-protocol command to configure the modem protocol. Syntax: (config-dpeer-fxs)# modem-protocol {none|pass-through} Field Definition none A Modem call would be treated as a normal voice call. Default. pass-through Will cause the line to transmit in G.711 mode, with echo cancellation and silence suppression disabled, on detection of Modem tone.
Configuration - Dial Peer FXS Mode no commands no commands no block-out-caller-id Use the Dial Peer no block-out-caller-id command to disable the Caller ID blocking. To enable blocking, see block-out-caller-id command on page 7-2. Syntax: (config-dpeer-fxs)# no block-out-caller-id Example: (config-dpeer-fxs)# no block-out-caller-id Supported Platforms: Adit 3104, Adit 3500 no call-wait-caller-id Use the Dial Peer no call-wait-caller-id command to disable Call Waiting Caller ID.
Configuration - Dial Peer FXS Mode no commands no codec preference Use the Dial Peer no codec preference command to remove a codec preference. To set the codec preferences, see codec preference command on page 7-3. Syntax: (config-dpeer-fxs)# no codec preference {1|2|3} Field Definition 1|2|3 Remove a specific codec preference.
Configuration - Dial Peer FXS Mode sip-authentication sip-authentication Note: To disable this SIP authentication, see no sip-authentication command on page 7-9. sip-authentication enable Use the Dial Peer sip-authentication enable command to enable SIP.
CHAPTER 8 Configuration - Dial Peer Trunk Mode The Dial Peer Trunk Configuration commands allow the user to configure the Dial Peer Trunk parameters. Note: The Dial Peer Trunk option is not supported on the Adit 3104. Enter this sub-group with the (config)# dial-peer voice pots trunk trunk dest-port command from the Configure mode. The Dial Peer Trunk commands are represented by the (config-dpeer-trk)# prompt.
Configuration - Dial Peer Trunk Mode codec preference codec preference Use the Dial Peer codec preference command to set the codec preferences used to establish the codec list offered during media negotiation. To delete a preference, see no codec preference command on page 8-7. Syntax: (config-dpeer-trk)# codec preference {1|2|3} {g711alaw| g711ulaw|g729} Field Definition 1|2|3 Enter the preference number. #1 being the first preference. g711alaw Set the codec preference to G.711 A-law.
Configuration - Dial Peer Trunk Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - Dial Peer Trunk Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Syntax: (config-dpeer-trk)# end Example: (config-dpeer-trk)# end # Supported Platforms: Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - Dial Peer Trunk Mode fax-protocol fax-protocol Use the Dial Peer fax-protocol command to configure the fax protocol. Syntax: (config-dpeer-trk)# fax-protocol {none|pass-through|t38| t38=reserved} Field Definition none A Fax call would be treated as a normal voice call. Default. pass-through Will cause the line to transmit in G.711 mode, with echo cancellation and silence suppression disabled, on detection of Fax tone.
Configuration - Dial Peer Trunk Mode modem-protocol modem-protocol Use the Dial Peer modem-protocol command to configure the modem protocol. Syntax: (config-dpeer-trk)# modem-protocol {none|pass-through} Field Definition none A Modem call would be treated as a normal voice call. Default. pass-through Will cause the line to transmit in G.711 mode, with echo cancellation and silence suppression disabled, on detection of Modem tone.
Configuration - Dial Peer Trunk Mode no commands no commands no codec preference Use the Dial Peer no codec preference command to remove a codec preference. To set the preferences, see codec preference command on page 8-2. Syntax: (config-dpeer-trk)# no codec preference {1|2|3} Field Definition 1|2|3 Set the preference level. Range 1 - 3.
Configuration - Dial Peer Trunk Mode prefix prefix Use the Dial Peer prefix command to define the prefix of the phone number. Syntax: (config-dpeer-trk)# prefix prefix Field Definition prefix Prefix is the digits or a name to be added to the phone number after the stripping process has been applied. Up to 10 digits may be entered.
Configuration - Dial Peer Trunk Mode strip-digits sip-authentication username Use the Dial Peer sip-authentication username command to set the SIP ID. Syntax: (config-dpeer-trk)# sip-authentication username username Field Definition username The User ID to be used when responding to authentication requests. Default is the User ID of the line.
Configuration - Dial Peer Trunk Mode strip-digits 8-10 Adit 3000 CLI - Release 1.
CHAPTER 9 Configuration - Dial Peer VoIP Mode The Dial Peer VoIP Configuration commands allow the user to configure the Dial Peer VoIP parameters. Enter this sub-group with the (config)# dial-peer voice voip port command from the Configure mode. The Dial Peer VoIP commands are represented by the (config-dpeer-voip)# prompt.
Configuration - Dial Peer VoIP Mode destination-pattern destination-pattern Use the Dial Peer destination-pattern command to define the full telephone number to be used for a dial peer. To delete a preference, see no destination-pattern command on page 9-5. Syntax: (config-dpeer-voip)# destination-pattern number Field Definition number Enter the phone number to be used for a dial peer.
Configuration - Dial Peer VoIP Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - Dial Peer VoIP Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Syntax: (config-dpeer-voip) end Example: (config-dpeer-voip)# end # Supported Platforms: Adit 3104, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - Dial Peer VoIP Mode no commands no commands no destination-pattern Use the Dial Peer no destination-pattern command to remove a destination pattern. To set the destination pattern, see destination-pattern command on page 9-2. Syntax: (config-dpeer-voip)# no destination-pattern Example: (config-dpeer-voip)# no destination-pattern Supported Platforms: Adit 3500 no prefix Use the Dial Peer no prefix command to remove the prefix of the phone number.
Configuration - Dial Peer VoIP Mode prefix prefix Use the Dial Peer prefix command to define the prefix of the phone number. To delete a prefix, see no prefix command on page 9-5. Syntax: (config-dpeer-voip)# prefix prefix Field Definition prefix Prefix is the digits or a name to be added to the phone number after the stripping process has been applied. Up to 10 digits may be entered.
Configuration - Dial Peer VoIP Mode strip-digits strip-digits Use the Dial Peer strip-digits command to configure the number of digits (or characters) to be stripped off from the left most digits in the phone number. Possible usages include stripping off the area code, or the 3-digit office prefix. Syntax: (config-dpeer-voip)# strip-digits number Field Definition number Range is based on the defined phone number. Default is set to 0.
Configuration - Dial Peer VoIP Mode user-id 9-8 Adit 3000 CLI - Release 1.
CHAPTER 10 Configuration - Ethernet Interface Mode The Ethernet Interface Configuration commands allow the user to configure the Controller parameters. Enter this sub-group with the (config)# interface ethernet command from the Configure mode. The Ethernet Interface commands are represented by the (config-int-eth-{n})# prompt.
Configuration - Ethernet Interface Mode description description Use the Ethernet Interface description command to set the description for this Ethernet interface. Syntax: (config-int-eth-{n})# description text Field Definition text Enter a description for the Ethernet interface with a maximum of 64 characters. Example: (config-int-eth-1)# description Eth#1 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 10-2 Adit 3000 CLI - Release 1.
Configuration - Ethernet Interface Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - Ethernet Interface Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Note: This command can be entered in any configuration mode with the same result. Syntax: (config-int-eth-{n})# end Example: (config-int-eth-1)# end # Supported Platforms: Adit 3104, Adit 3200, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - Ethernet Interface Mode full-duplex full-duplex Use the Ethernet Interface full-duplex command to specify the Ethernet PHY (physical specifications) mode to full duplex. Syntax: (config-int-eth-{n})# full-duplex Example: (config-int-eth-1)# full-duplex Supported Platforms: Adit 3104, Adit 3200, Adit 3500 half-duplex Use the Ethernet Interface half-duplex command to specify the Ethernet PHY (physical specifications) mode to half duplex.
Configuration - Ethernet Interface Mode history history Use the history command to display commands that have been entered in this session. Note: This command can be entered in any configuration mode.
Configuration - Ethernet Interface Mode ip default-gateway ip default-gateway Use the Ethernet Interface ip default-gateway command to set the default gateway for the Ethernet port. Syntax: (config-int-eth-{n})# ip default-gateway address Field Definition address Enter a default gateway address to the Ethernet port. Example: (config-int-eth-1)# ip default-gateway 192.168.100.
Configuration - Ethernet Interface Mode ip mtu ip mtu Use the Ethernet Interface ip mtu command to set the Maximum Transmission Unit. Sets the largest packet size (bytes) the network will allow to transmit. Syntax: (config-int-eth-{n})# ip mtu {size|auto} Field Definition size Allows the user to set the Maximum Transmission Unit (MTU). size = range of 576 to 1500 bytes. auto Auto sets the MTU at 1500 bytes.
Configuration - Ethernet Interface Mode ip ospf authentication ip ospf authentication Use the Ethernet Interface ip ospf authentication command to enable the authentication method (either message-digest or simple authentication) for this Ethernet interface. To remove the authentication type for this interface set the parameter to null or see no ip ospf authentication command on page 10-18.
Configuration - Ethernet Interface Mode ip ospf authentication-key ip ospf authentication-key Use the Ethernet Interface ip ospf authentication-key command to assign a password to be used by neighboring routers, that are using OSPF’s simple password authentication.To remove a previously assigned password, see no ip ospf authentication-key command on page 10-18. Syntax: (config-int-eth-{n})# ip ospf authentication-key password Field Definition password Enter a password, with up to 8 characters.
Configuration - Ethernet Interface Mode ip ospf disable ip ospf disable Use the Ethernet Interface ip ospf disable command to disable OSPF processing on this interface. To enable OSPF on this interface, see no ip ospf disable command on page 10-19.
Configuration - Ethernet Interface Mode ip ospf priority ip ospf priority Use the Ethernet Interface ip ospf priority command to set the router priority, which determines the designated router for this network. To restore the default setting of priority 1, see no ip ospf priority command on page 10-20. Syntax: (config-int-eth-{n})# ip ospf priority priority Field Definition priority Enter an ID for this key. Range is 0-255.
Configuration - Ethernet Interface Mode ip primary-dns ip primary-dns Use the Ethernet Interface ip primary-dns command to configure the primary DNS. To delete a primary DNS, see no ip primary-dns command on page 10-20. Syntax: (config-int-eth-{n})# ip primary-dns address Field Definition address Enter the IP address of the primary server. Example: (config-int-eth-1)# ip primary-dns 192.168.1.
Configuration - Ethernet Interface Mode ip rip ip rip ip rip enable Use the Ethernet Interface ip rip enable command to enable RIP on this interface. To disable RIP, see no ip rip command on page 10-21. Syntax: (config-int-eth-{n})# ip rip enable Example: (config-int-eth-1)# ip rip enable Supported Platforms: Adit 3104, Adit 3200, Adit 3500 ip rip receive-version Use the Ethernet Interface ip rip receive-version command to configure the RIP receive messages on this interface.
Configuration - Ethernet Interface Mode ip route ip route Use the Ethernet Interface ip route command to configure the static routes on this interface. To delete a route, see no ip route command on page 10-21. Syntax: (config-int-eth-{n})# ip route dest-ip-addr mask mask gateway gateway metric metric Field Definition dest-ip-addr Enter the destination IP address. mask Enter the mask of the above address. gateway Enter the gateway IP address.
Configuration - Ethernet Interface Mode ip secondary-dns ip secondary-dns Use the Ethernet Interface ip secondary-dns command to configure the secondary DNS. To delete a secondary DNS address, see no ip secondary-dns command on page 10-21. Syntax: (config-int-eth-{n})# ip secondary-dns address Field Definition address Enter the IP address of the secondary Domain Name Server (DNS). Example: (config-int-eth-1)# ip secondary-dns 192.168.1.
Configuration - Ethernet Interface Mode no commands no commands no firewall Use the no firewall command to disable the configured firewall. To enable the firewall, see firewall command on page 10-4. Syntax: (config-int-eth-{n})# no firewall Example: (config-int-eth-1)# no firewall Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ip address Use the Ethernet Interface no ip address command to remove the IP address from the alias. To set the Ethernet IP address, see ip address command on page 10-6.
Configuration - Ethernet Interface Mode no commands no ip ospf authentication Use the Ethernet Interface no ip ospf authentication command to disable the authentication method for this Ethernet interface. To enable the authentication type for this interface see ip ospf authentication command on page 10-9.
Configuration - Ethernet Interface Mode no commands no ip ospf disable Use the Ethernet Interface no ip ospf disable command to enable OSPF processing on this interface. To disable OSPF on this interface, see ip ospf disable command on page 10-11.
Configuration - Ethernet Interface Mode no commands no ip ospf priority Use the Ethernet Interface no ip ospf priority command to set the router priority to the default setting of priority 1. To set the router priority, which determines the designated router for this network, see ip ospf priority command on page 10-12.
Configuration - Ethernet Interface Mode no commands no ip proxy-arp Use the Ethernet Interface no ip proxy-arp command to disable the proxy ARP on this interface. To enable proxy ARP, see ip proxy-arp command on page 10-13. Syntax: (config-int-eth-{n})# no ip proxy-arp Example: (config-int-eth-1)# no ip proxy-arp Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ip rip Use the Ethernet Interface no ip rip command to disable RIP on this interface. To enable RIP, see ip rip command on page 10-14.
Configuration - Ethernet Interface Mode no commands no remote-admin Use the Ethernet Interface no remote-admin command to disable remote access on this interface. To enable remote access, see remote-admin command on page 10-24. Syntax: (config-int-eth-{n})# no remote-admin Example: (config-int-eth-1)# no remote-admin Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no schedule-availability Use the Ethernet Interface no schedule-availability command to disable a schedule rule.
Configuration - Ethernet Interface Mode no commands no tos ip Use the Ethernet Interface no tos ip command to disable IP TOS marking. To enable TOS marking, see tos command on page 10-26. Syntax: (config-int-eth-{n})# no tos ip Example: (config-int-eth-1)# no tos ip Supported Platforms: Adit 3104, Adit 3200, Adit 3500 Adit 3000 CLI - Release 1.
Configuration - Ethernet Interface Mode release release Use the Ethernet Interface release command to release the DHCP lease. Syntax: (config-int-eth-{n})# release Example: (config-int-eth-1)# release Supported Platforms: Adit 3104, Adit 3200, Adit 3500 remote-admin Use the Ethernet Interface remote admin command to enable Remote Access on this interface. To disable remote access, see no remote-admin command on page 10-22.
Configuration - Ethernet Interface Mode schedule-availability schedule-availability Use the Ethernet Interface schedule-availability command to apply a schedule rule to this interface. To delete a schedule, see no schedule-availability command on page 10-22. Syntax: (config-int-eth-{n})# schedule-availability time-range schedule-id Field Definition schedule-id Enter an existing schedule rule name.
Configuration - Ethernet Interface Mode speed speed Use the Ethernet Interface speed command to specify the Ethernet PHY (physical specifications) speed. Syntax: (config-int-eth-{n})# speed {10|100|auto} Field Definition 10 10 Mbps speed . 100 100 Mbps speed. auto Auto-negotiate the speed for the interface. Default. Note: Setting speed to auto will set the duplex to auto.
CHAPTER 11 Configuration - Multilink Interface Mode The Multilink Interface Configuration commands allow the user to configure the MLPPP connections. Enter this sub-group with the (config)# interface multilink number command from the Configure mode. The Multilink Interface commands are represented by the (config-int-mlink-{n})# prompt.
Configuration - Multilink Interface Mode description description Use the Multilink Interface description command to set the description for this Multilink interface. Syntax: (config-int-mlink-{n})# description text Field Definition text Enter a description for the Multilink interface with a maximum of 64 characters. Example: (config-int-mlink-1)# description MLPPP1 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 11-2 Adit 3000 CLI - Release 1.
Configuration - Multilink Interface Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - Multilink Interface Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Note: This command can be entered in any configuration mode with the same result. Syntax: (config-int-mlink-{n})# end Example: (config-int-mlink-1)# end # Supported Platforms: Adit 3104, Adit 3200, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - Multilink Interface Mode history history Use the history command to display commands that have been entered in this session. Note: This command can be entered in any configuration mode.
Configuration - Multilink Interface Mode ip default-route ip default-route Use the Multilink Interface ip default-route command to enable the default route. To disable the default route, see no ip default-route command on page 11-14. Syntax: (config-int-mlink-{n})# ip default-route enable Example: (config-int-mlink-1)# ip default-route enable Supported Platforms: Adit 3104, Adit 3200, Adit 3500 ip mtu Use the Multilink Interface ip mtu command to set the Maximum Transmission Unit.
Configuration - Multilink Interface Mode ip ospf authentication ip ospf authentication Use the Multilink Interface ip ospf authentication command to enable the authentication method (either message-digest or simple authentication) for this Multilink interface. To remove the authentication type for this interface set the parameter to null or see no ip ospf authentication command on page 11-14.
Configuration - Multilink Interface Mode ip ospf authentication-key ip ospf authentication-key Use the Multilink Interface ip ospf authentication-key command to assign a password to be used by neighboring routers, that are using OSPF’s simple password authentication.To remove a previously assigned password, see no ip ospf authentication-key command on page 11-15. Syntax: (config-int-mlink-{n})# ip ospf authentication-key password Field Definition password Enter a password, with up to 8 characters.
Configuration - Multilink Interface Mode ip ospf disable ip ospf disable Use the Multilink Interface ip ospf disable command to disable OSPF processing on this interface. To enable OSPF on this interface, see no ip ospf disable command on page 11-15.
Configuration - Multilink Interface Mode ip ospf priority ip ospf priority Use the Multilink Interface ip ospf priority command to set the router priority, which determines the designated router for this network. To restore the default setting of priority 1, see no ip ospf priority command on page 11-16. Syntax: (config-int-mlink-{n})# ip ospf priority priority Field Definition priority Enter an ID for this key. Range is 0-255.
Configuration - Multilink Interface Mode ip primary-dns ip primary-dns Use the Multilink Interface ip primary-dns command to configure the primary DNS. To delete a primary DNS, see no ip primary-dns command on page 11-17. Syntax: (config-int-mlink-{n})# ip primary-dns address Field Definition address Enter the IP address of the primary server. Example: (config-int-mlink-1)# ip primary-dns 10.10.5.
Configuration - Multilink Interface Mode ip route ip rip send-version Use the Multilink Interface ip rip send-version command to configure the send RIP messages on this interface. Syntax: (config-int-mlink-{n})# ip rip send-version {1|2-bcast|2-mcast |none} Field Definition 1 Send RIP version 1. 2-bcast Send RIP version 2 - Broadcast. 2-mcast Send RIP version 2 - Multicast. none Set RIP version to none.
Configuration - Multilink Interface Mode ip route-mode ip route-mode Use the Multilink Interface ip route-mode command to configure the routing mode. Syntax: (config-int-mlink-{n})# ip route-mode {napt|route} Field Definition napt Set to NAPT mode. Default. NAPT is used if doing private IPs on the Ethernet side or if you want to hide specific publics on the internal side. route Set to Route mode. Routing is used if public is visible on both sides.
Configuration - Multilink Interface Mode no commands no commands no firewall Use the Multilink Interface no firewall command to disable the configured firewall. To enable the firewall on this interface, see firewall command on page 11-4. Syntax: (config-int-mlink-{n})# no firewall Example: (config-int-mlink-1)# no firewall Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ip address Use the Multilink Interface no ip address command to remove the IP address assigned to the port.
Configuration - Multilink Interface Mode no commands no ip ospf authentication-key Use the Multilink Interface no ip ospf authentication-key command to remove a password to be used by neighboring routers, that are using OSPF’s simple password authentication.To assign a password, see ip ospf authentication-key command on page 11-8.
Configuration - Multilink Interface Mode no commands no ip ospf hello-interval Use the Multilink Interface no ip ospf hello-interval command to reset the interval of time to the default setting of the path cost to the default setting of 10 seconds. To define the interval of time between hello packets that the Adit 3000 sends on the interface, see ip ospf hello-interval command on page 11-9.
Configuration - Multilink Interface Mode no commands no ip ospf retransmit-interval Use the Multilink Interface ip ospf retransmit-interval command to restore the default value of 5 seconds. To define the interval of time between link state advertisement retransmissions for adjacencies belonging to the interface, see ip ospf retransmit-interval command on page 11-10.
Configuration - Multilink Interface Mode no commands no ip route Use the Multilink Interface no ip route command remove an IP route. To add a route, see ip route command on page 11-12. Syntax: (config-int-mlink-{n})# no ip route dest-ip-addr gateway Field Definition dest-ip-addr Enter destination IP address to remove. gateway Enter gateway IP address to remove. Example: (config-int-mlink-1)# no ip route 192.168.100.200 192.168.100.
Configuration - Multilink Interface Mode no commands no ppp on-demand Use the Multilink Interface no ppp on-demand command to disable PPP on-demand. To enable PPP on demand, see ppp on-demand command on page 11-22. Syntax: (config-int-mlink-{n})# no ppp on-demand Example: (config-int-mlink-1)# no ppp on-demand Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ppp password Use the Multilink Interface no ppp password command to remove the PPP password.
Configuration - Multilink Interface Mode no commands no schedule-availability Use the Multilink Interface no schedule-availability command to disable a schedule rule. To add a rule, see schedule-availability command on page 11-24. Syntax: (config-int-mlink-{n})# no schedule-availability Example: (config-int-mlink-1)# no schedule-availability Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no shutdown Use the Multilink Interface no shutdown command to set the Multilink port up (In-Service).
Configuration - Multilink Interface Mode ppp authentication ppp authentication Use the Multilink Interface ppp authentication command to configure the support of authentication types for the password. To disable PPP authentication, see no ppp authentication command on page 11-18. Syntax: (config-int-mlink-{n})# ppp authentication {chap|ms-chapv1| ms-chapv2|pap} Field Definition chap Support Challenge Handshake Authentication (CHAP) ms-chapv1 Support Microsoft CHAP (MS-CHAP).
Configuration - Multilink Interface Mode ppp link-fragmentation ppp link-fragmentation Use the Multilink Interface ppp link-fragmentation command to configure the threshold byte size of the packet, for Interleaving. Note: If the packet is > the set threshold, the packet will be split in half and sent. Syntax: (config-int-mlink-{n})# ppp link-fragmentation number Field Definition number Range 320 - 1600, with a default of 1600 bytes.
Configuration - Multilink Interface Mode ppp qos-interleaving ppp qos-interleaving Use the Multilink Interface ppp qos-interleaving command enable PPP Quality of Service Interleaving. To disable PPP QoS Interleaving, see no ppp qos interleaving command on page 11-19.
Configuration - Multilink Interface Mode ppp username ppp username Use the Multilink Interface ppp username command set the PPP Login User Name. To delete a PPP user, see no ppp qos interleaving command on page 11-19. Syntax: (config-int-mlink-{n})# ppp username username Field Definition username Enter the Username, with a maximum of 19 characters.
Configuration - Multilink Interface Mode sip-alg sip-alg Use the Multilink Interface sip-alg command to enable SIP ALG. To disable SIP ALG, see no sip-alg command on page 11-20. Syntax: (config-int-mlink-{n})# sip-alg enable Example: (config-int-mlink-1)# sip-alg enable Supported Platforms: Adit 3104, Adit 3500 Adit 3000 CLI - Release 1.
Configuration - Multilink Interface Mode sip-alg 11-26 Adit 3000 CLI - Release 1.
CHAPTER 12 Configuration - Serial Interface Mode The Serial Interface Configuration commands allow the user to configure the Serial port parameters. Enter this sub-group with the (config)# interface serial number command from the Configure mode. The Serial Interface commands are represented by the (config-int-ser-{n})# prompt.
Configuration - Serial Interface Mode description description Use the Serial Interface description command to set the description for this Serial interface. Syntax: (config-int-ser-{n})# description text Field Definition text Enter a description for the Serial interface with a maximum of 64 characters. Example: (config-int-ser-1)# description Serial1 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 12-2 Adit 3000 CLI - Release 1.
Configuration - Serial Interface Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - Serial Interface Mode encapsulation ppp encapsulation ppp Use the Serial Interface encapsulation ppp command to enable PPP encapsulation. To disable encapsulation, see no encapsulation ppp command on page 12-14. Syntax: (config-int-ser-{n})# encapsulation ppp Example: (config-int-ser-1)# encapsulation ppp Supported Platforms: Adit 3104, Adit 3200, Adit 3500 end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file.
Configuration - Serial Interface Mode firewall firewall Use the Serial interface firewall command to enable the configured firewall. To delete a preference, see no firewall command on page 12-14. Syntax: (config-int-ser-{n})# firewall enable Example: (config-int-ser-1)# firewall enable Supported Platforms: Adit 3104, Adit 3200, Adit 3500 history Use the history command to display commands that have been entered in this session. Note: This command can be entered in any configuration mode.
Configuration - Serial Interface Mode ip address ip address Use the Serial Interface ip address command to configure the IP address for the port. To remove an IP address, see no ip address command on page 12-15. Syntax: (config-int-ser-{n})# ip address {address mask mask|auto |unnumbered} [secondary] Field Definition address Enter an IP address to assign to the port. mask Enter a subnet mask for the IP address. auto Uses IPCP to assign an IP address.
Configuration - Serial Interface Mode ip ospf authentication ip ospf authentication Use the Serial Interface ip ospf authentication command to enable the authentication method (either message-digest or simple authentication) for this Serial interface. To remove the authentication type for this interface set the parameter to null or see no ip ospf authentication command on page 12-15.
Configuration - Serial Interface Mode ip ospf authentication-key ip ospf authentication-key Use the Serial Interface ip ospf authentication-key command to assign a password to be used by neighboring routers, that are using OSPF’s simple password authentication.To remove a previously assigned password, see no ip ospf authentication-key command on page 12-15. Syntax: (config-int-ser-{n})# ip ospf authentication-key password Field Definition password Enter a password, with up to 8 characters.
Configuration - Serial Interface Mode ip ospf disable ip ospf disable Use the Serial Interface ip ospf disable command to disable OSPF processing on this interface. To enable OSPF on this interface, see no ip ospf disable command on page 12-16.
Configuration - Serial Interface Mode ip ospf priority ip ospf priority Use the Serial Interface ip ospf priority command to set the router priority, which determines the designated router for this network. To restore the default setting of priority 1, see no ip ospf priority command on page 12-17. Syntax: (config-int-ser-{n})# ip ospf priority priority Field Definition priority Enter an ID for this key. Range is 1-255.
Configuration - Serial Interface Mode ip primary-dns ip primary-dns Use the Serial Interface ip primary-dns command to configure the primary DNS. To delete a primary DNS, see no ip primary-dns command on page 12-18. Syntax: (config-int-ser-{n})# ip primary-dns address Field Definition address Enter the IP address of the primary server. Example: (config-int-ser-1)# ip primary-dns 192.168.1.
Configuration - Serial Interface Mode ip route ip rip send-version Use the Serial Interface ip rip send-version command to configure the send RIP messages on this interface. Syntax: (config-int-ser-{n})# ip rip send-version {1|2-bcast|2-mcast |none} Field Definition 1 Send RIP version 1. 2-bcast Send RIP version 2 - Broadcast. 2-mcast Send RIP version 2 - Multicast. none Set RIP version to none.
Configuration - Serial Interface Mode ip route-mode ip route-mode Use the Serial Interface ip route-mode command to configure the routing mode. Syntax: (config-int-ser-{n})# ip route-mode {napt|route} Field Definition napt Set to NAPT mode. Default. NAPT is used if doing private IPs on the Ethernet side or if you want to hide specific publics on the internal side. route Set to Route mode. Routing is used if public is visible on both sides.
Configuration - Serial Interface Mode multilink-group multilink-group Use the Serial Interface multilink-group command to configure a MLPPP group. Syntax: (config-int-ser-{n})# multilink-group group-number Field Definition group-number Enter multilink group. Range = 1. Example: (config-int-ser-1)# multilink-group 1 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no commands no encapsulation ppp Use the Serial Interface no encapsulation ppp command to disable PPP encapsulation.
Configuration - Serial Interface Mode no commands no ip address Use the Serial Interface no ip address command to remove the IP address assigned to the port. To set the Serial IP address, see ip address command on page 12-6. Syntax: (config-int-ser-{n})# no ip address address Field Definition address Enter the IP address to remove. Example: (config-int-ser-1)# no ip address 192.168.1.
Configuration - Serial Interface Mode no commands no ip ospf cost Use the Serial Interface no ip ospf cost command to reset the cost path to the default setting of 0. To define the cost of sending a packet on this Serial interface, see ip ospf cost command on page 12-8.
Configuration - Serial Interface Mode no commands no ip ospf message-digest-key Use the Serial Interface no ip ospf message-digest-key command to remove an old MD5 key. To enable OSPF MD5 (Message-Digest) authentication, see ip ospf message-digest-key command on page 12-9. Syntax: (config-int-ser-{n})# no ip ospf message-digest-key key-id Field Definition key-id Enter an ID for this key. Range is 1-255.
Configuration - Serial Interface Mode no commands no ip primary-dns Use the Serial Interface no primary-dns command to disable the primary DNS. To set the DNS primary IP address, see ip primary-dns command on page 12-11. Syntax: (config-int-ser-{n})# no ip primary-dns Example: (config-int-ser-1)# no ip primary-dns Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ip rip Use the Serial Interface no ip rip command to disable RIP on this interface. To enable RIP, see ip rip command on page 12-11.
Configuration - Serial Interface Mode no commands no ppp authentication Use the Serial Interface no ppp authentication command disable PPP authentication. To enable PPP authentication, see ppp authentication command on page 12-21. Syntax: (config-int-ser-{n})# no ppp authentication Example: (config-int-ser-1)# no ppp authentication Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ppp encryption Use the Serial Interface no ppp encryption command to disable PPP encryption.
Configuration - Serial Interface Mode no commands no ppp username Use the Serial Interface no ppp username command remove the PPP username. To set a PPP user, see ppp username command on page 12-23. Syntax: (config-int-ser-{n})# no ppp username username Example: (config-int-ser-1)# no ppp username test-user-name Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no schedule-availability Use the Serial Interface no schedule-availability command to disable a schedule rule.
Configuration - Serial Interface Mode ppp authentication ppp authentication Use the Serial Interface ppp authentication command to configure the support of authentication types for the password. To disable PPP authentication, see no ppp authentication command on page 12-19. Syntax: (config-int-ser-{n})# ppp authentication {chap|ms-chap| ms-chapv2|pap} Field Definition chap Support Challenge Handshake Authentication (CHAP) ms-chap Support Microsoft CHAP (MS-CHAP).
Configuration - Serial Interface Mode ppp link-fragmentation ppp link-fragmentation Use the Serial Interface ppp link-fragmentation command to configure the threshold byte size of the packet, for Interleaving. Note: If the packet is > the set threshold, the packet will be split in half and sent. Syntax: (config-int-ser-{n})# ppp link-fragmentation number Field Definition number Range 320 - 1600, with a default of 1600 bytes.
Configuration - Serial Interface Mode ppp restart-timer ppp restart-timer Use the Serial Interface ppp restart-timer command to configure the PPP restart timer. Syntax: (config-int-ser-{n})# ppp restart-timer seconds Field Definition seconds Range is 1 - 65535 seconds. Default is 3 seconds.
Configuration - Serial Interface Mode schedule-availability schedule-availability Use the Serial Interface schedule-availability command to apply a schedule rule to this interface. To delete a schedule, see no schedule-availability command on page 12-20. Syntax: (config-int-ser-{n})# schedule-availability time-range schedule-id Field Definition schedule-id Enter an existing schedule rule name.
CHAPTER 13 Configuration - IPSec Mode The IPSecConfiguration commands allow the user to configure the VPN IPSec parameters. Enter this sub-group with the (config)# ipsec vpn_ipsec command from the Configure mode. The IPSec commands are represented by the (config-ipsec-1)# prompt. Note: First a connection must be created. See ipsec net-to-host command on page 4-21, or ipsec net-tonet command on page 4-22.
Configuration - IPSec Mode aggressive-mode aggressive-mode Use the IPSec aggressive-mode command to set to aggressive mode, instead of main mode. To set to main mode, see no aggressive-mode command on page 13-13. Syntax: (config-ipsec {n})# aggressive-mode Example: (config-ipsec-1)# aggressive-mode Supported Platforms: Adit 3104, Adit 3200, Adit 3500 authentication Use the IPSec authentication command to specify a peer authentication method.
Configuration - IPSec Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - IPSec Mode dpd-delay dpd-delay Use the IPSec dpd-delay command to set the Dead Period Detection delay. To set the DPD delay back to the default settings, see no dpd-delay command on page 13-13. Syntax: (config-ipsec {n})# dpd-delay seconds Field Definition seconds Set the delay time in seconds. Range 1-3600 seconds, with a default of 60.
Configuration - IPSec Mode encryption encryption Use the IPSec encryption command to specify an encryption algorithm. To disable encryption, see no group command on page 13-14. Syntax: (config-ipsec {n})# encryption {des|3des|aes|aes192|aes256} Field Definition des Set to 56-bit Data Encryption Standard (DES). 3des Set to 168-bit DES. Default. aes Set 128-bit Advanced Encryption Standard (AES) as the encryption algorithm. aes192 Set 192-bit AES as the encryption algorithm.
Configuration - IPSec Mode group group Use the IPSec group command to define the Diffie-Hellman (DH) group identifier for phase-1. Note: More than one group can be enabled. To disable a DH identifier, see no group command on page 13-14. Syntax: (config-ipsec {n})# group {1|2|5} Field Definition 1 Set to DH group 1 (768 bit). 2 Set to DH group 2 (1024 bit). Default is enabled. 5 Set to DH group 25 (1536 bit). Default is enabled.
Configuration - IPSec Mode history history Use the history command to display commands that have been entered in this session. Note: This command can be entered in any configuration mode.
Configuration - IPSec Mode ip rip ip rip ip rip enable Use the IPSec ip rip enable command to enable RIP on this interface. To disable RIP, see no ip rip command on page 13-15. Syntax: (config-ipsec-{n})# ip rip enable Example: (config-ipsec-1)# ip rip enable Supported Platforms: Adit 3104, Adit 3200, Adit 3500 ip rip receive-version Use the IPSec ip rip receive-version command to configure the RIP receive messages on this interface.
Configuration - IPSec Mode ip route metric ip route metric Use the IPSec mode ip route metric command to define a number for the device metric. Syntax: (config-ipsec {n})# ip route metric metric Field Definition metric Enter a number for the device metric. Range is 0-255, with a default of 10. Example: (config-ipsec-1)# ip route metric 25 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 ipsec-conn Use the IPSec mode ipsec-conn command to enable or disable an IPSec connection without removing it.
Configuration - IPSec Mode key key Use the IPSec key command to set the shared secret key. Syntax: (config-ipsec {n})# key key Field Definition key Enter a shared secret key, with a maximum of 30 characters. Example: (config-ipsec-1)# key mysecret Supported Platforms: Adit 3104, Adit 3200, Adit 3500 lifetime Use the IPSec mode lifetime command to set the connection lifetime. Syntax: (config-ipsec {n})# lifetime time seconds Field Definition seconds Set the connection lifetime.
Configuration - IPSec Mode local-subnet local-subnet Use the IPSec mode local-subnet command to set the local subnet IP address. Syntax: (config-ipsec {n})# local-subnet {none|range {start-address address end-address address}|single ip address|subnet ip address} Field Definition none No IP address. range Enter an IP address range. start-address - Enter the start IP address of the range. end-address - Enter the end IP address of the range. single ip Enter a single IP address.
Configuration - IPSec Mode mode mode Use the IPSec mode mode command to modify an IPSec security association mode. Note: If a router requests tunnel mode, only tunnel mode can be negotiated between the peers. However, if transport mode is requested, either transport or tunnel mode can be negotiated. Syntax: (config-ipsec {n})# mode {transport|tunnel} Field Definition transport Transport Mode - only the payload of the original IP packet is encrypted and/or authenticated.
Configuration - IPSec Mode netbios remote-ip netbios remote-ip Use the IPSec netbios remote-ip command to set the remote broadcast address for NetBIOS. Syntax: (config-int-ser-{n})# netbios remote-ip address Field Definition address Enter the remote broadcast address. Example: (config-int-ser-1)# netbios remote-ip 192.168.1.
Configuration - IPSec Mode no commands no dpd-timeout Use the IPSec no dpd-timeout command to set the Dead Period Detection (DPD) timeout to the default setting. To set DPD timeout, see dpd-timeout command on page 13-4. Syntax: (config-int-ser-{n})# no dpd-timeout Example: (config-int-ser-1)# no dpd-timeout Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no encryption Use the IPSec no encryption command to disable encryption. To configure encryption, see encryption command on page 13-5.
Configuration - IPSec Mode no commands no hash Use the IPSec no hash command to disable a hash algorithm. To set a hash algorithm, see hash command on page 13-6. Syntax: (config-int-ser-{n})# no hash {md5|sha} Field Definition md5 Disable the MD5 algorithm. sha Disable SHA1. SHA = Secure Hash Algorithm. Example: (config-int-ser-1)# no hash md5 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ip default-route Use the IPSec no ip default-route command to remove an existing IPSec connection.
Configuration - IPSec Mode no commands no netbios Use the IPSec no netbios command to disable routing of NetBIOS broadcasts. To enable NetBIOS broadcasts, see netbios command on page 13-12. Syntax: (config-int-ser-{n})# no netbios Example: (config-int-ser-1)# no netbios Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no reconnect Use the IPSec no reconnect command to disable automatic reconnection. To enable reconnection, see reconnect command on page 13-18.
Configuration - IPSec Mode no commands no transform-set Use the IPSec no transform-set command to disable Perfect Forward Secrecy. To enable PFS, see transform-set command on page 13-21. Syntax: (config-int-ser-{n})# no transform-set {ah-md5|ah-sha|esp-3des| esp-aes|esp-aes192|esp-aes256|esp-des|esp-md5|esp-null|esp-sha |ipcomp} Field Definition ah-md5 Authentication Header transform using MD5 authentication. Default.
Configuration - IPSec Mode reconnect reconnect Use the IPSec reconnect command to enable the automatic reconnection option. To disable reconnection, see no reconnect command on page 13-16. Syntax: (config-int-ser-{n})# reconnect Example: (config-int-ser-1)# reconnect Supported Platforms: Adit 3104, Adit 3200, Adit 3500 rekey Use the IPSec rekey command to set the rekey lifetime, rekey margin and rekey fuzz percent.
Configuration - IPSec Mode remote-subnet remote-subnet Use the IPSec remote-subnet command to set the remote subnet IP address. Syntax: Syntax: (config-int-ser-{n})# remote-subnet {none|range {start-address address end-address address}|single ip address|subnet ip address} Field Definition none No IP address. range Enter an IP address range. start-address - Enter the start IP address of the range. end-address - Enter the end IP address of the range. single ip Enter a single IP address.
Configuration - IPSec Mode session-key session-key Use the IPSec session-key command to specify the parameters needed during manual key exchange (ipsec-manual). No command. session-key ah Syntax: (config-int-ser-{n})# session-key {inbound|outbound} ah spi authentication [md5|sha] hex-key-data Field Definition inbound Set the inbound (local) IPSec key. outbound Set the outbound (remote) IPSec key. ah spi Set the Authentication Header Security Parameter Index.
Configuration - IPSec Mode transform-set transform-set Use the IPSec transform-set command to set the allowable encryption methods, authentication protocols and to enable compression during automatic key exchange. To disable encryption/ authentication/compression, see no transform-set command on page 13-17.
Configuration - IPSec Mode transform-set Example of IPSec Connection Configuration Adit 3104(config)#ipsec VPN_IPSEC 0 Adit 3104(config-ipsec-0)#dev-name VPNIPSec0 Adit 3104(config-ipsec-0)#net-type WAN Adit 3104(config-ipsec-0)#aggressive-mode Adit 3104(config-ipsec-0)#authentication pre-share ocho Adit 3104(config-ipsec-0)#no encryption des Adit 3104(config-ipsec-0)#no encryption 3des Adit 3104(config-ipsec-0)#no encryption aes Adit 3104(config-ipsec-0)#encryption aes192 Adit 3104(config-ipsec-0)#no encr
Configuration - IPSec Mode transform-set Adit 3104(config-ipsec-0)#transform-set esp-null Adit 3104(config-ipsec-0)#transform-set esp-des Adit 3104(config-ipsec-0)#transform-set esp-3des Adit 3104(config-ipsec-0)#transform-set esp-aes Adit 3104(config-ipsec-0)#transform-set esp-aes192 Adit 3104(config-ipsec-0)#transform-set esp-aes256 Adit 3104(config-ipsec-0)#transform-set esp-md5 Adit 3104(config-ipsec-0)#transform-set esp-sha Adit 3104(config-ipsec-0)#transform-set ah-md5 Adit 3104(config-ipsec-0)#trans
Configuration - IPSec Mode transform-set 13-24 Adit 3000 CLI - Release 1.
CHAPTER 14 Configuration - L2TPC Mode The L2TPC Configuration commands allow the user to configure the VPN Layer 2 Tunneling Protocol Connection (L2TPC) parameters. Enter this sub-group with the (config)# l2tp command from the Configure mode. The VPN L2TPC commands are represented by the (config-l2tpc-1)# prompt.
Configuration - L2TPC Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - L2TPC Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Note: This command can be entered in any configuration mode with the same result. Syntax: (config-l2tpc-{n})# end Example: (config-l2tpc-1)# end # Supported Platforms: Adit 3104, Adit 3200, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - L2TPC Mode history history Use the history command to display commands that have been entered in this session. Note: This command can be entered in any configuration mode. Syntax: (config-l2tpc-{n})# history Example: (config-l2tpc-1)# history firewall enable exit host-ip 192.168.1.10 ip default-route enable ip rip enable ip rip send-version none ip primary-dns 192.168.2.10 ip route 192.168.1.160 history Supported Platforms: Adit 3104, Adit 3200, Adit 3500 14-4 Adit 3000 CLI - Release 1.
Configuration - L2TPC Mode ip address ip address Use the L2TPC ip address command to configure the IP address for the port. To remove an IP address, see no ip address command on page 14-13. Syntax: (config-l2tpc-{n})# ip address {address mask mask|auto |unnumbered} [secondary] Field Definition address Enter an IP address to assign to the port. mask Enter a subnet mask for the IP address. auto Uses IPCP to assign an IP address. unnumbered Treat this as an un-numbered interface, as per RFC 1812.
Configuration - L2TPC Mode ip ospf authentication ip ospf authentication Use the L2TPC ip ospf authentication command to enable the authentication method (either messagedigest or simple authentication) for this interface. To remove the authentication type for this interface set the parameter to null or see no ip ospf authentication command on page 14-13. Note: If an optional parameter is not entered, the authentication method of simple authentication is applied to the interface.
Configuration - L2TPC Mode ip ospf authentication-key ip ospf authentication-key Use the L2TPC ip ospf authentication-key command to assign a password to be used by neighboring routers, that are using OSPF’s simple password authentication.To remove a previously assigned password, see no ip ospf authentication-key command on page 14-14. Syntax: (config-l2tpc-{n})# ip ospf authentication password Field Definition password Enter a password, with up to 8 characters.
Configuration - L2TPC Mode ip ospf disable ip ospf disable Use the L2TPC ip ospf disable command to disable OSPF processing on this interface. To enable OSPF on this interface, see no ip ospf disable command on page 14-14.
Configuration - L2TPC Mode ip ospf priority ip ospf priority Use the L2TPC ip ospf priority command to set the router priority, which determines the designated router for this network. To restore the default setting of priority 1, see no ip ospf priority command on page 14-15. Syntax: (config-l2tpc-{n})# ip ospf priority priority Field Definition priority Enter an ID for this key. Range is 0-255.
Configuration - L2TPC Mode ip primary-dns ip primary-dns Use the L2TPC ip primary-dns command to configure the primary DNS. To delete a primary DNS, see no ip primary-dns command on page 14-16. Syntax: (config-l2tpc-{n})# ip primary-dns address Field Definition address Enter the IP address of the primary server. Example: (config-l2tpc-1)# ip primary-dns 192.168.2.
Configuration - L2TPC Mode ip route ip rip send-version Use the L2TPC ip rip send-version command to configure the send RIP messages on this interface. Syntax: (config-l2tpc-{n})# ip rip send-version {1|2-bcast|2-mcast |none} Field Definition 1 Send RIP version 1. 2-bcast Send RIP version 2 - Broadcast. 2-mcast Send RIP version 2 - Multicast. none Set RIP version to none.
Configuration - L2TPC Mode ip route-mode ip route-mode Use the L2TPC ip route-mode command to configure the routing mode. Syntax: (config-l2tpc-{n})# ip route-mode {napt|route} Field Definition napt Set to NAPT mode. Default. NAPT is used if doing private IPs on the Ethernet side or if you want to hide specific publics on the internal side. route Set to Route mode. Routing is used if public is visible on both sides.
Configuration - L2TPC Mode no commands no commands no firewall Use the L2TPC no firewall command to disable the configured firewall. To enable the firewall, see firewall command on page 14-3. Syntax: (config-l2tpc-{n})# no firewall Example: (config-l2tpc-1)# no firewall Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ip address Use the L2TPC no ip address command to remove the IP address assigned to the port. To set the Serial IP address, see ip address command on page 14-5.
Configuration - L2TPC Mode no commands no ip ospf authentication-key Use the L2TPC no ip ospf authentication-key command to remove a password to be used by neighboring routers, that are using OSPF’s simple password authentication.To assign a password, see ip ospf authentication-key command on page 14-7.
Configuration - L2TPC Mode no commands no ip ospf hello-interval Use the L2TPC no ip ospf hello-interval command to reset the interval of time to the default setting of the path cost to the default setting of 10 seconds. To define the interval of time between hello packets that the Adit 3000 sends on the interface, see ip ospf hello-interval command on page 14-8.
Configuration - L2TPC Mode no commands no ip ospf retransmit-interval Use the L2TPC ip ospf retransmit-interval command to restore the default value of 5 seconds. To define the interval of time between link state advertisement retransmissions for adjacencies belonging to the interface, see ip ospf retransmit-interval command on page 14-9.
Configuration - L2TPC Mode no commands no ip route Use the L2TPC no ip route command remove an IP route. To add a route, see ip route command on page 14-11. Syntax: (config-l2tpc-{n})# no ip route dest-ip-addr gateway Field Definition dest-ip-addr Enter destination IP address to remove. gateway Enter gateway IP address to remove. Example: (config-l2tpc-1)# no ip route 192.168.100.200 192.168.100.
Configuration - L2TPC Mode no commands no ppp exec-timeout Use the L2TPC no ppp exec-timeout command to disable PPP idle time. To set the PPP maximum idle time before hangup, see ppp exec-timeout command on page 14-21. Syntax: (config-l2tpc-{n})# no ppp exec-timeout Example: (config-l2tpc-1)# no ppp exec-timeout Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ppp on-demand Use the L2TPC no ppp on-demand command to disable PPP on-demand.
Configuration - L2TPC Mode no commands no ppp time-btwn-reconnect Use the L2TPC no ppp time-btwn-reconnect command to reset this time to the default settings. To set the interval between reconnect attempts, see ppp time-btwn-reconnect command on page 14-22. Syntax: (config-l2tpc-{n})# no ppp time-btwn-reconnect Example: (config-l2tpc-1)# no ppp time-btwn-reconnect Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ppp username Use the L2TPC no ppp username command remove the PPP username.
Configuration - L2TPC Mode ppp authentication no sip-alg Use the L2TPC no sip-alg command to disable SIP ALG on this interface. To enable SIP ALG, see sip-alg command on page 14-23. Syntax: (config-l2tpc-{n})# no sip-alg Example: (config-l2tpc-1)# no sip-alg Supported Platforms: Adit 3104, Adit 3500 ppp authentication Use the L2TPC ppp authentication command to configure the support of authentication types for the password. To disable PPP authentication, see no ppp authentication command on page 14-17.
Configuration - L2TPC Mode ppp exec-timeout ppp exec-timeout Use the L2TPC ppp exec-timeout command to set the PPP maximum idle time before hangup.To disable PPP idle time, see no ppp exec-timeout command on page 14-18. Syntax: (config-l2tpc-{n})# ppp exec-timeout minutes Field Definition minutes Range is 0 - 99999 minutes.
Configuration - L2TPC Mode ppp restart-timer ppp restart-timer Use the L2TPC ppp restart-timer command to configure the PPP restart timer. To set the restart timer to the default setting, see no ppp restart-timer command on page 14-18. Syntax: (config-l2tpc-{n})# ppp restart-timer seconds Field Definition seconds Range is 1 - 65535 seconds. Default is 3 seconds.
Configuration - L2TPC Mode schedule-availability schedule-availability Use the L2TPC schedule-availability command to apply a schedule rule to this interface. To delete a schedule, see no schedule-availability command on page 14-19. Syntax: (config-l2tpc-{n})# schedule-availability time-range scheduleid Field Definition schedule-id Enter an existing schedule rule name.
Configuration - L2TPC Mode sip-alg 14-24 Adit 3000 CLI - Release 1.
CHAPTER 15 Configuration - OSPF Mode The Router OSPF Configuration commands allow the user to configure the OSPF parameters. OSPF (Open Shortest Path First) is a protocol based on the link-states of routers within a network. OSPF supports hierarchical routing by segmenting a larger network into smaller more manageable networks called areas. Enter this sub-group with the (config)# router ospf command from the Configure mode. The Router OSPF commands are represented by the (config-ospf)# prompt.
Configuration - OSPF Mode area commands area commands Note: On the following area commands, the first command that enters the area ID, will set this parameter. The no area command will remove a specific area from the configuration. See see no area command on page 15-7. area authentication Use the Router OSPF area authentication command to enable authentication method (either message-digest or simple authentication) for an OSPF area. The default setting is no authentication.
Configuration - OSPF Mode compatible rfc1583 compatible rfc1583 Use the Router OSPF compatible rfc1583 command to restore the method used to calculate summary route costs per RFC 1583. To disable RFC 1583 compatibility, see the no compatible rfc1583 command on page 15-8. Syntax: (config-ospf)# compatible rfc1583 Example: (config-ospf)# compatible rfc1583 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 Adit 3000 CLI - Release 1.
Configuration - OSPF Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - OSPF Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Note: This command can be entered in any configuration mode with the same result. Syntax: (config-ospf)# end Example: (config-ospf)# end # Supported Platforms: Adit 3104, Adit 3200, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - OSPF Mode network area network area Use the Router OSPF network area command to define the interfaces on which OSPF will run and set the ID for those interfaces. To disable OSPF routing for the interface defined, see no network area command on page 15-8. Syntax: (config-ospf)# network address wildcard-mask area area-id Field Definition address IP address wildcard-mask IP address-type mask that includes "don’t care" bits.
Configuration - OSPF Mode no commands no commands no area Use the Router OSPF no area command to remove a specific area from the OSPF configuration. To set an area, see the area commands command on page 15-2, or area stub command on page 15-2, the first use of either command will set the area. Syntax: (config-ospf)# no area area-id Field Definition area-id ID of area to be removed, in the form: area number - Range 0-4294967295 area IP address - IP address of the area.
Configuration - OSPF Mode no commands no compatible rfc1583 Use the Router OSPF no compatible rfc1583 command to disable RFC 1583 compatibility. To restore RFC 1583 compatibility, see compatible rfc1583 command on page 15-3 Syntax: (config-ospf)# no compatible rfc1583 Example: (config-ospf)# no compatible rfc1583 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no network area Use the Router OSPF no network area command to disable OSPF routing for the interface defined.
Configuration - OSPF Mode router-id router-id Use the Router OSPF router-id command to use a fixed router ID. To force OSPF to use the previous OSPF router ID behavior use the no form of this command, see no router-id command on page 15-8. Syntax: (config-ospf)# router-id address Field Definition address Router ID in IP address format. Example: (router-ospf)# router-id 10.1.1.1 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 Adit 3000 CLI - Release 1.
Configuration - OSPF Mode router-id Sample Configuration ospf router ospf no compatible rfc1583 router-id 192.168.3.251 network 192.168.3.0 0.0.0.255 area 0.0.0.1 interface ethernet 1 ip address 192.168.2.251 mask 255.255.255.0 description Ethernet 1 ip mtu auto no tos ip tos ip value 0x0 ip default-gateway 0.0.0.
Configuration - OSPF Mode router-id ip ospf priority 2 exit interface ethernet 2 ip address 192.168.3.251 mask 255.255.255.0 description Ethernet 2 ip mtu auto ip default-gateway 192.168.3.
Configuration - OSPF Mode router-id 15-12 Adit 3000 CLI - Release 1.
CHAPTER 16 Configuration - PPTPC Mode The PPTPC Configuration commands allow the user to configure the VPN (Virtual Private Network) Point-to-Point Tunneling Protocol Client parameters. Enter this sub-group with the (config)# pptp command from the Configure mode. The VPN PPTPC commands are represented by the (config-pptpc-1)# prompt.
Configuration - PPTPC Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - PPTPC Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Note: This command can be entered in any configuration mode with the same result. Syntax: (config-pptpc-{n})# end Example: (config-pptpc-1)# end # Supported Platforms: Adit 3104, Adit 3200, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - PPTPC Mode history history Use the history command to display commands that have been entered in this session. Note: This command can be entered in any configuration mode.
Configuration - PPTPC Mode ip address ip address Use the PPTP Client ip address command to configure the IP address for the port. To remove an IP address, see no ip address command on page 16-13. Syntax: (config-pptpc-{n})# ip address {address mask mask|auto |unnumbered} [secondary] Field Definition address Enter an IP address to assign to the port. mask Enter a subnet mask for the IP address. auto Uses IPCP to assign an IP address.
Configuration - PPTPC Mode ip ospf authentication ip ospf authentication Use the PPTP Client ip ospf authentication command to enable the authentication method (either message-digest or simple authentication) for this interface. To remove the authentication type for this interface set the parameter to null or see no ip ospf authentication command on page 16-13. Note: If an optional parameter is not entered, the authentication method of simple authentication is applied to the interface.
Configuration - PPTPC Mode ip ospf authentication-key ip ospf authentication-key Use the PPTP Client ip ospf authentication-key command to assign a password to be used by neighboring routers, that are using OSPF’s simple password authentication.To remove a previously assigned password, see no ip ospf authentication-key command on page 16-14. Syntax: (config-pptpc-{n})# ip ospf authentication password Field Definition password Enter a password, with up to 8 characters.
Configuration - PPTPC Mode ip ospf disable ip ospf disable Use the PPTP Client ip ospf disable command to disable OSPF processing on this interface. To enable OSPF on this interface, see no ip ospf disable command on page 16-14.
Configuration - PPTPC Mode ip ospf priority ip ospf priority Use the PPTP Client ip ospf priority command to set the router priority, which determines the designated router for this network. To restore the default setting of priority 1, see no ip ospf priority command on page 16-15. Syntax: (config-pptpc-{n})# ip ospf priority priority Field Definition priority Enter an ID for this key. Range is 0-255.
Configuration - PPTPC Mode ip primary-dns ip primary-dns Use the PPTP Client ip primary-dns command to configure the primary DNS. To delete a primary DNS, see no ip primary-dns command on page 16-16. Syntax: (config-pptpc-{n})# ip primary-dns address Field Definition address Enter the IP address of the primary server. Example: (config-pptpc-1)# ip primary-dns 192.168.2.
Configuration - PPTPC Mode ip route ip rip send-version Use the PPTP Client ip rip send-version command to configure the send RIP messages on this interface. Syntax: (config-pptpc-{n})# ip rip send-version {1|2-bcast|2-mcast |none} Field Definition 1 Send RIP version 1. 2-bcast Send RIP version 2 - Broadcast. 2-mcast Send RIP version 2 - Multicast. none Set RIP version to none.
Configuration - PPTPC Mode ip route-mode ip route-mode Use the PPTP Client ip route-mode command to configure the routing mode. Syntax: (config-pptpc-{n})# ip route-mode {napt|route} Field Definition napt Set to NAPT mode. Default. NAPT is used if doing private IPs on the Ethernet side or if you want to hide specific publics on the internal side. route Set to Route mode. Routing is used if public is visible on both sides.
Configuration - PPTPC Mode no commands no commands no firewall Use the PPTP Client no firewall command to disable the configured firewall. To enable the firewall, see firewall command on page 16-3. Syntax: (config-pptpc-{n})# no firewall Example: (config-pptpc-1)# no firewall Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ip address Use the PPTP Client no ip address command to remove the IP address assigned to the port. To set the Serial IP address, see ip address command on page 16-5.
Configuration - PPTPC Mode no commands no ip ospf authentication-key Use the PPTP Client no ip ospf authentication-key command to remove a password to be used by neighboring routers, that are using OSPF’s simple password authentication.To assign a password, see ip ospf authentication-key command on page 16-7.
Configuration - PPTPC Mode no commands no ip ospf hello-interval Use the PPTP Client no ip ospf hello-interval command to reset the interval of time to the default setting of the path cost to the default setting of 10 seconds. To define the interval of time between hello packets that the Adit 3000 sends on the interface, see ip ospf hello-interval command on page 16-8.
Configuration - PPTPC Mode no commands no ip ospf retransmit-interval Use the PPTP Client ip ospf retransmit-interval command to restore the default value of 5 seconds. To define the interval of time between link state advertisement retransmissions for adjacencies belonging to the interface, see ip ospf retransmit-interval command on page 16-9.
Configuration - PPTPC Mode no commands no ip route Use the PPTP Client no ip route command remove an IP route. To add a route, see ip route command on page 16-11. Syntax: (config-pptpc-{n})# no ip route dest-ip-addr gateway Field Definition dest-ip-addr Enter destination IP address to remove. gateway Enter gateway IP address to remove. Example: (config-pptpc-1)# no ip route 192.168.100.200 192.168.100.
Configuration - PPTPC Mode no commands no ppp exec-timeout Use the PPTP Client no ppp exec-timeout command to disable PPP idle time. To set the PPP maximum idle time before hangup, see ppp exec-timeout command on page 16-21. Syntax: (config-pptpc-{n})# no ppp exec-timeout Example: (config-pptpc-1)# no ppp exec-timeout Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ppp on-demand Use the PPTP Client no ppp on-demand command to disable PPP on-demand.
Configuration - PPTPC Mode no commands no ppp time-btwn-reconnect Use the PPTP Client no ppp time-btwn-reconnect command to set the time between reconnect attempts to the default setting. To configure the time between reconnect attempts, see ppp timebtwn-reconnect command on page 16-23.
Configuration - PPTPC Mode no commands Example: (config-pptpc-1)# no shutdown Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no sip-alg Use the PPTP Client no sip-alg command to disable SIP ALG on this interface. To enable SIP ALG, see sip-alg command on page 16-24. Syntax: (config-pptpc-{n})# no sip-alg Example: (config-pptpc-1)# no sip-alg Supported Platforms: Adit 3104, Adit 3500 16-20 Adit 3000 CLI - Release 1.
Configuration - PPTPC Mode ppp authentication ppp authentication Use the PPTP Client ppp authentication command to configure the support of authentication types for the password. To disable PPP authentication, see no ppp authentication command on page 16-17. Syntax: (config-pptpc-{n})# ppp authentication {chap|ms-chap| ms-chapv2|pap} Field Definition chap Support Challenge Handshake Authentication (CHAP) ms-chap Support Microsoft CHAP (MS-CHAP).
Configuration - PPTPC Mode ppp on-demand ppp on-demand Use the PPTP Client ppp on-demand command to enable on demand the feature. On demand attempts to connect only when packets are sent. To disable PPP on demand, see no ppp encryption command on page 16-17. Syntax: (config-pptpc-{n})# ppp on-demand Example: (config-pptpc-1)# ppp on-demand Supported Platforms: Adit 3104, Adit 3200, Adit 3500 ppp password Use the PPTP Client ppp password command set the PPP password.
Configuration - PPTPC Mode ppp time-btwn-reconnect ppp time-btwn-reconnect Use the PPTP Client ppp time-btwn-reconnect command configure the time between reconnect attempts. To reset to the default setting, see no ppp time-btwn-reconnect command on page 16-19. Syntax: (config-pptpc-{n})# ppp time-btwn-reconnect seconds Field Definition seconds Set the interval of time between reconnect attempts. Range is 0 - 99999 seconds with a default of 0.
Configuration - PPTPC Mode shutdown shutdown Use the PPTP Client shutdown command to disable the Serial port. To set the Serial port up (In-Service), see no shutdown command on page 16-19. Syntax: (config-pptpc-{n})# shutdown Example: (config-pptpc-1)# shutdown Supported Platforms: Adit 3104, Adit 3200, Adit 3500 sip-alg Use the PPTP Client sip-alg command to enable SIP ALG. To disable SIP ALG, see no sip-alg command on page 16-20.
CHAPTER 17 Configuration - PPTPS Mode The PPTP Server Configuration commands allow the user to configure the VPN (Virtual Private Network) Point-to Point Tunneling Protocol Server parameters. Enter this sub-group with the (config)# pptps command from the Configure mode. The VPN PPTP Server commands are represented by the (config-pptps)# prompt.
Configuration - PPTPS Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - PPTPS Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Note: This command can be entered in any configuration mode with the same result. Syntax: (config-pptps)# end Example: (config-pptps)# end # Supported Platforms: Adit 3104, Adit 3200, Adit 3500 end-address Use the PPTP Server end-address command to set the PPTP remote host IP address range end.
Configuration - PPTPS Mode history history Use the history command to display commands that have been entered in this session. Note: This command can be entered in any configuration mode. Syntax: (config-pptps)# history Example: (config-pptps)# history ppp end-address 192.168.1.175 ppp encryption ppp authentication pap idle-time 99999 start-address 192.168.1.
Configuration - PPTPS Mode no commands no commands no idle-time Use the PPTP Server no idle-time command to reset the idle time to the default setting. To set the maximum idle time for a PPTP connection, see idle-time command on page 17-4. Syntax: (config-pptps)# no idle-time Example: (config-pptps)# no idle-time Supported Platforms: Adit 3104, Adit 3200, Adit 3500 no ppp authentication Use the PPTP Server no ppp authentication command to disable PPP authentication.
Configuration - PPTPS Mode ppp authentication no shutdown Use the PPTP Server no shutdown command to set the admin state of the server up (in-service). To set the admin state of the server down (out-of-service), see shutdown command on page 17-7. Syntax: (config-pptps)# no shutdown Example: (config-pptps)# no shutdown Supported Platforms: Adit 3104, Adit 3200, Adit 3500 ppp authentication Use the PPTP Server ppp authentication command to configure the support of authentication types for the password.
Configuration - PPTPS Mode shutdown shutdown Use the PPTP Server shutdown command to set the admin state of the server down (out-of-service). To set the admin state up (in-service), see no shutdown command on page 17-6. Syntax: (config-pptps)# shutdown Example: (config-pptps)# shutdown Supported Platforms: Adit 3104, Adit 3200, Adit 3500 start-address Use the PPTP Server start-address command to set the PPTP remote host IP address range start.
Configuration - PPTPS Mode start-address 17-8 Adit 3000 CLI - Release 1.
CHAPTER 18 Configuration - RADIUS Mode The RADIUS Configuration commands allow the user to configure the RADIUS parameters for each interface. This sub-group is entered with the (config)# radius-client command from the Configure mode. The RADIUS commands are represented by the (config-radius)# prompt.
Configuration - RADIUS Mode authentication authentication Use the RADIUS authentication command to set the RADIUS client authentication method. Syntax: (config-radius)# authentication {chap|ms-chap|ms-chapv2|pap} Field Definition chap CHAP - Challenge Handshake Authentication ms-chap MS-CHAP - Microsoft CHAP ms-chapv2 MS-CHAPv2 - Microsoft CHAP Version 2 pap PAP - Unencrypted Password.
Configuration - RADIUS Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - RADIUS Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Note: This command can be entered in any configuration mode with the same result. Syntax: (config-radius)# end Example: (config-radius)# end # Supported Platforms: Adit 3104, Adit 3200, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - RADIUS Mode host host Use the RADIUS host command to set the RADIUS server IP address on the system. Syntax: (config-radius)# host address auth-port port Field Definition address Enter the IP address of the RADIUS server. port Enter the port number to use for RADIUS authentication. Range is 0 65535 with a default of 1812. Example: (config-radius)# host 192.168.1.
Configuration - RADIUS Mode key 18-6 Adit 3000 CLI - Release 1.
CHAPTER 19 Configuration - VLAN Mode The VLAN Configuration commands allow the user to configure the global VLAN parameters. This sub-group is entered with the (config)# vlan command from the Configure mode. The global VLAN commands are represented by the (config-vlan)# prompt.
Configuration - VLAN Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - VLAN Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Note: This command can be entered in any configuration mode with the same result. Syntax: (config-vlan)# end Example: (config-vlan)# end # Supported Platforms: Adit 3104, Adit 3200, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - VLAN Mode no command no command no port-dot1q Use the VLAN no port-dot1q command to disable dot1q tagging for the port. By default, VLAN tagging is disabled on a LAN port. In this default state, if the port receives a VLAN tagged frame, it will ignore the VLAN header and will process the ingress frames as a regular Ethernet frame. The VLAN tag will not be altered. Note: Ingress port is a port receiving frames from a source external to the switch.
Configuration - VLAN Mode port-priority port-priority Use the VLAN port-priority command to set the VLAN priority for the port. Syntax: (config-vlan)# port-priority ethernet port priority Field Definition port Ethernet port in the form {port}.{sub-interface}. Adit 3104 and Adit 3200 = 1.1, 1.2, 1.3, 1.4, 2.1 Adit 3500 = 1.1 and 2.1 priority Set priority level. Range = 0 - 7. Default is 0. Example: (config-vlan)# port-priority ethernet 1.
Configuration - VLAN Mode pvid pvid Use the VLAN pvid command to set the port native VLAN ID, or PVID. Syntax: (config-vlan)# pvid ethernet port Field Definition port Ethernet port in the form {port}.{sub-interface}. Adit 3104 and Adit 3200 = 1.1, 1.2, 1.3, 1.4, 2.1 Adit 3500 = 1.1 and 2.1 Example: (config-vlan)# port-protocol-filter enable ethernet 1.1 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 tag-all Use the VLAN tag-all command to enable dot1q tagging for all ports.
Configuration - VLAN Mode vlan-feature vlan-feature Use the VLAN mode vlan-feature command to enable/disable the VLAN feature on the device. Note: This command is not visible on the Adit 3500, as it is always enabled on this product. Syntax: (config-vlan)# vlan-feature {disable|enable} Field Definition disable Disable VLAN feature. enable Enable VLAN feature. Example: (config-vlan)# vlan-feature enable Supported Platforms: Adit 3104, Adit 3200 Adit 3000 CLI - Release 1.
Configuration - VLAN Mode vlan-feature 19-8 Adit 3000 CLI - Release 1.
CHAPTER 20 Configuration - VLAN Port Mode The VLAN Port Configuration commands allow the user to configure the VLAN port parameters. This sub-group is entered with the (config)# vlan {vlan-id} command from the Configure mode. The VLAN Port commands are represented by the (config-vlan-{n})# prompt.
Configuration - VLAN Port Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - VLAN Port Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Note: This command can be entered in any configuration mode with the same result. Syntax: (config-vlan-{n})# end Example: (config-vlan-100)# end # Supported Platforms: Adit 3104, Adit 3200, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - VLAN Port Mode no commands no commands no port Use the VLAN no port command to remove this port’s membership from the VLAN. To set the preferences, see port command on page 20-5. Syntax: (config-vlan-{n})# no port ethernet port Field Definition port Ethernet port in the form {port}.{sub-interface}. Adit 3104 and Adit 3200 = 1.1, 1.2, 1.3, 1.4, 2.1 Adit 3500 = 1.1 and 2.1 Example: (config-vlan-100)# no port ethernet 1.
Configuration - VLAN Port Mode port port Use the VLAN port command to set the Ethernet port as a VLAN port member. Syntax: (config-vlan-{n})# port ethernet port Field Definition port Ethernet port in the form {port}.{sub-interface}. Adit 3104 and Adit 3200 = 1.1, 1.2, 1.3, 1.4, 2.1 Adit 3500 = 1.1 and 2.1 Example: (config-vlan-100)# port ethernet 1.1 Supported Platforms: Adit 3104, Adit 3200, Adit 3500 priority Use the VLAN priority command to set the VLAN priority level.
Configuration - VLAN Port Mode voice-interface 20-6 Adit 3000 CLI - Release 1.
CHAPTER 21 Configuration - Voice Port Mode The Voice Port Configuration commands allow the user to configure the Voice Port parameters. Enter this sub-group with the (config)# voice-port command from the Configure mode. The Voice Port commands are represented by the (config-vport)# prompt. Note: There are two additional Voice Port groups (FXS-Chapter 22 and Trunk-Chapter 23), please see their respective chapters for information.
Configuration - Voice Port Mode digit-map (global) digit-map (global) Use the Voice Port digit-map global command to configure the Digit Map on a global level. To disable digit map, see no digit-map (global) command on page 21-5. Syntax: (config-vport)# digit-map mode {long-timeout seconds |pattern number pattern |short-timeout seconds} Field Definition long-timeout seconds Range is 4-60 seconds, with a default of 16. pattern number - Enter pattern number to modify. Range is 1-30.
Configuration - Voice Port Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - Voice Port Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Note: This command can be entered in any configuration mode with the same result. Syntax: (config-vport)# end Example: (config-vport)# end # Supported Platforms: Adit 3104, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - Voice Port Mode no digit-map (global) no digit-map (global) Use the Voice Port no digit-map command to remove a digit map pattern. To configure digit map, see digit-map (global) command on page 21-2. Syntax: (config-vport)# no digit-map pattern number Field Definition pattern number Enter pattern number to remove. Range is 1-30. See show digit-map command on page 3-37, to display the current list of Digit Map numbers.
Configuration - Voice Port Mode tos 21-6 Adit 3000 CLI - Release 1.
CHAPTER 22 Configuration - Voice Port FXS Mode The Voice Port FXS Configuration commands allow the user to configure the Voice Port FXS parameters. Enter this sub-group with the (config)# voice-port fxs number command from the Configure mode. The Voice Port FXS commands are represented by the (config-vport-fxs-{n})# prompts.
Configuration - Voice Port FXS Mode comfort-noise comfort-noise Use the Voice Port FXS comfort-noise command to enable the comfort noise feature. To to disable comfort noise, see no comfort-noise command on page 22-6. Syntax: (config-vport-fxs-{n})# comfort-noise enable Example: (config-vport-fxs-1)# comfort-noise enable Supported Platforms: Adit 3104, Adit 3500 description Use the Voice Port FXS description command to set the circuit ID of the voice port.
Configuration - Voice Port FXS Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - Voice Port FXS Mode echo-cancel echo-cancel Use the Voice Port FXS echo-cancel command to enable Echo Cancellation on this trunk. To to disable Echo Cancellation, see no echo-cancel command on page 22-6 Syntax: (config-vport-fxs-{n})# echo-cancel enable Example: (config-vport-fxs-1)# echo-cancel enable Supported Platforms: Adit 3104, Adit 3500 end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file.
Configuration - Voice Port FXS Mode history history Use the history command to display commands that have been entered in this session. Syntax: (config-vport-fxs-{n})# history Example: (config-vport-fxs-1)# history description tests echo-cancel enable input-gain 4 output-gain 4 signal ground-start history Supported Platforms: Adit 3104, Adit 3500 input-gain Use the Voice Port FXS input-gain command to set the gain on the receive side voice path for the specified voice channel(s).
Configuration - Voice Port FXS Mode no commands no commands no comfort-noise Use the Voice Port FXS no comfort-noise command to disable comfort noise. To enable remote access, see comfort-noise command on page 22-2. Syntax: (config-vport-fxs-{n})# no comfort-noise Example: (config-vport-fxs-1)# no comfort-noise Supported Platforms: Adit 3104, Adit 3500 no echo-cancel Use the Voice Port FXS no echo-cancel command disable echo cancellation on this port.
Configuration - Voice Port FXS Mode output-gain output-gain Use the Voice Port FXS output-gain command to set the gain on the transmit side voice path for the specified voice channel(s). Syntax: (config-vport-fxs-{n})# output-gain value Field Definition value Range -12 to +6dB. Default is 0. Example: (config-vport-fxs-1)# output-gain 4 Supported Platforms: Adit 3104, Adit 3500 per-line-logging Use the Voice Port FXS per-line-logging command to enable the logging per line feature.
Configuration - Voice Port FXS Mode signal signal Use the Voice Port FXS signal command to set the signaling protocol. Syntax: (config-vport-fxs-{n})# signal {ground-start|loop-start} Field Definition ground-start Sets the line to Ground Start signaling loop-start Sets the line to Loop Start signaling Example: (config-vport-fxs-1)# signal ground-start Supported Platforms: Adit 3104, Adit 3500 22-8 Adit 3000 CLI - Release 1.
CHAPTER 23 Configuration - Voice Port Trunk Mode The Voice Port Trunk Configuration commands allow the user to configure the Voice Port Trunk parameters. Enter this sub-group with the (config)# voice-port trunk number command from the Configure mode. Note: The Trunk option is not supported on the Adit 3104 or the Adit 3200. The Voice Port Trunk commands are represented by the (config-vport-trk-{n})# prompt.
Configuration - Voice Port Trunk Mode comfort-noise comfort-noise Use the Voice Port Trunk comfort-noise command to enable the comfort noise feature. To disable this feature, see no comfort-noise command on page 23-8. Syntax: (config-vport-trk-{n})# comfort-noise enable Example: (config-vport-trk-1)# comfort-noise enable Supported Platforms: Adit 3500 connection t1 Use the Voice Port Trunk connection t1 command to enter the T1 connection configuration mode.
Configuration - Voice Port Trunk Mode digit-map digit-map Use the Voice Port Trunk digit-map command to configure the Digit Map on the trunk level. To disable digit map, see no digit-map command on page 23-8. Syntax: (config-vport-trk-{n})# digit-map mode {default|custom} Field Definition default Pass dialed number as a complete number for routing to the phone book, or to the proxy if there are no phone book entries. custom Process as for the default digit map.
Configuration - Voice Port Trunk Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - Voice Port Trunk Mode echo-cancel echo-cancel Use the Voice Port Trunk echo-cancel command to enable Echo Cancellation on this trunk. To disable Echo Cancellation, see no echo-cancel command on page 23-9. Syntax: (config-vport-trk-{n})# echo-cancel enable Example: (config-vport-trk-1)# echo-cancel enable Supported Platforms: Adit 3500 end Use the end command to exit the current Configuration mode.
Configuration - Voice Port Trunk Mode history history Use the history command to display commands that have been entered in this session. Syntax: (config-vport-trk-1)# history Example: (config-vport-trk-1)# history exit description VoiceP-#1 digit-map mode custom history Supported Platforms: Adit 3500 input-gain Use the Voice Port Trunk input-gain command to set the gain on the receive side voice path for the specified voice channel(s).
Configuration - Voice Port Trunk Mode isdn switch-type (PRI) isdn switch-type (PRI) Use the Voice Port Trunk isdn switch-type command to configure the switching type (protocol) on this trunk. Note: Hunt sequence of the PRI is a Round-Robin type, and is not configurable. Syntax: (config-vport-trk-{n})# isdn switch-type {pri-dms100|pri-4ess |pri-5ess|pri-ni2} Field Definition pri-4ess PRI-4ess - The class 4 US AT&T proprietary version of ISDN.
Configuration - Voice Port Trunk Mode no commands no commands no comfort-noise Use the Voice Port Trunk no comfort-noise command to disable comfort noise. To enable remote access, see comfort-noise command on page 23-2. Syntax: (config-vport-trk-{n})# no comfort-noise Example: (config-vport-trk-1)# no comfort-noise Supported Platforms: Adit 3500 no connection t1 Use the Voice Port Trunk no connection t1 command to remove a T1 connection.
Configuration - Voice Port Trunk Mode no commands no echo-cancel Use the Voice Port Trunk no echo-cancel command disable echo cancellation on this port. To enable echo cancellation, see echo-cancel command on page 23-5. Syntax: (config-vport-trk-{n})# no echo-cancel Example: (config-vport-trk-1)# no echo-cancel Supported Platforms: Adit 3500 no registration enable Use the Voice Port Trunk no registration enable command disable trunk registration.
Configuration - Voice Port Trunk Mode output-gain no registration line enable Use the Voice Port Trunk no registration line enable command disable a registration line. To enable line registration, see registration line enable command on page 23-12. Syntax: (config-vport-trk-{n})# no registration line number enable Field Definition number Enter line number to disable. Range 1 -300. Note: This line must be enabled for this command to be accepted.
Configuration - Voice Port Trunk Mode registration registration The registration command enables the user to Add, Edit, Remove, Enable, Disable PBX line number behind a voice trunk that will register to the SIP proxy. registration enable Use the Voice Port Trunk registration enable command to enable the Voice Port registration feature. To disable Voice Port registration, see no registration enable command on page 23-9.
Configuration - Voice Port Trunk Mode registration registration line enable Use the Voice Port Trunk registration line enable command to enable registration. To disable registration, see no registration line enable command on page 23-10. Syntax: (config-vport-trk-{n})# registration line value line-numbers value enable Field Definition line value Enter the PBX line number to configure. Range is 1 - 300. line-numbers value Define the number of lines in this block that is going to be registered.
Configuration - Voice Port Trunk Mode signal registration line logging Use the Voice Port Trunk registration line authentication command to enable logging on this line. To disable logging, see no registration line logging command on page 23-10. Syntax: (config-vport-trk-{n})# registration line value line-numbers value logging Field Definition line value Enter the PBX line number to configure. Range is 1 - 300. line-numbers value Define the number of lines in this block that is going to be registered.
Configuration - Voice Port Trunk Mode trunk trunk Use the Voice Port Trunk trunk command to set the Trunk ID. Syntax: (config-vport-trk-{n})# trunk trunk-id Field Definition trunk-id Enter a trunk ID for this Voice Port Trunk. With a maximum of 20 characters. Example: (config-vport-trk-1)# trunk VPtrunk1 Supported Platforms: Adit 3500 23-14 Adit 3000 CLI - Release 1.
CHAPTER 24 Configuration - Voice Service SIP Mode The Voice Service SIP Configuration commands allow the user to configure the Voice Trunk SIP parameters. Enter this sub-group with the (config)# voice-service sip command from the Configure mode. The Voice Port commands are represented by the (config-voice-serv-sip)# prompt.
Configuration - Voice Service SIP Mode calling-party-disc calling-party-disc Use the Voice Service SIP calling-party-disc command to configure the call party disconnect feature. Syntax: (config-voice-serv-sip)# calling-party-disc duration Field Definition duration Range 500 - 3000 seconds. Example: (config-voice-serv-sip)# calling-party-disc 600 Supported Platforms: Adit 3104, Adit 3500 conference Use the Voice Service SIP conference command to enable the conference calling feature.
Configuration - Voice Service SIP Mode do do Use the do commands allow the user to run Privileged and User mode commands. The following are links to the Privileged and User "do" commands.
Configuration - Voice Service SIP Mode dtmf dtmf Use the Voice Service SIP dtmf command to configure the DTMF events. Syntax: (config-voice-serv-sip)# dtmf {inband|rfc2833} Field Definition inband Configure the DTMF in-band, as part of the RTP packets. rfc2833 Configure the DTMF events out-of-band, as RTP event packets. Example: (config-voice-serv-sip)# dtmf inband Supported Platforms: Adit 3104, Adit 3500 early-media Use the Voice Service SIP early-media command to configure the SIP early media.
Configuration - Voice Service SIP Mode end end Use the end command to exit the current configuration mode, and must be used to mark the end of any configuration file. Note: This command can be entered in any configuration mode with the same result. Syntax: (config-voice-serv-sip)# end Example: (config-voice-serv-sip)# end # Supported Platforms: Adit 3104, Adit 3500 exit Use the exit command to close your current connection if you are in the User mode, or Privileged mode.
Configuration - Voice Service SIP Mode fax-protocol-t38 redundancy fax-protocol-t38 redundancy Use the Voice Service SIP fax-protocol-t38 redundancy command to set the T.38 protocol high and low speed redundancy. Syntax: (config-voice-serv-sip)# fax-protocol-t38 {hs-redundancy value}|ls-redundancy value} Example: (config-voice-serv-sip)# fax-protocol-t38 hs-redundancy 1 Syntax Descriptions: Variable Definition hs-redundancy Configures the number of duplicate packets to transmit during a high-speed T.
Configuration - Voice Service SIP Mode feature-mode feature-mode Use the Voice Service SIP feature-mode command to determine where the intelligence for the calling features will lie, offering a choice between server-based (Info) and device-based (local) features. Syntax: (config-voice-serv-sip)# feature-mode {info|local} Field Definition info This selection is used with BroadSoft 11.1 Info Mode Proxy.
Configuration - Voice Service SIP Mode history history Use the history command to display commands that have been entered in this session. Note: This command can be entered in any configuration mode. Syntax: (config-voice-serv-sip)# history Example: (config-voice-serv-sip)# history feature-mode outbound-proxy outbound-proxy ip-address 192.168.2.2 dtmf inband outbound-proxy 192.168.1.140 proxy proxy-server 10.10.0.1 exit history Supported Platforms: Adit 3104, Adit 3500 24-8 Adit 3000 CLI - Release 1.
Configuration - Voice Service SIP Mode no commands no commands no conference Use the Voice Service SIP no conference command to disable the conference feature. To enable conference, see conference command on page 24-2. Syntax: (config-voice-serv-sip)# no conference Example: (config-voice-serv-sip)# no conference Supported Platforms: Adit 3104, Adit 3500 no outbound-proxy Use the Voice Service SIP no outbound-proxy command to disable the outbound proxy.
Configuration - Voice Service SIP Mode no commands no redundancy filter-incoming Use the Voice Service SIP no redundancy-filter-incoming command to disable the incoming redundancy filter. To enable filter, see redundancy filter-incoming command on page 24-14.
Configuration - Voice Service SIP Mode outbound-proxy outbound-proxy Use the Voice Service SIP outbound-proxy command to configure the SIP outbound proxy. To disable outbound proxy, see no outbound-proxy command on page 24-9. Syntax: (config-voice-serv-sip)# outbound-proxy {hostname hostname| ip-address address} Field Definition hostname Enter the host name of the outbound proxy. address Enter the IP address of the outbound proxy. Example: (config-voice-serv-sip)# outbound-proxy ip-address 192.168.
Configuration - Voice Service SIP Mode privacy-mode privacy-mode Use the Voice Service SIP privacy-mode command to configure the SIP privacy mode. Syntax: (config-voice-serv-sip)# privacy-mode {none|rfc3325} Field Definition none Disables the Privacy Mode. Default is None. rfc3325 Enables support for RFC 3325, as supported on the Sylantro Application Server.
Configuration - Voice Service SIP Mode proxy-type proxy-type Use the Voice Service SIP proxy-type command to configure the SIP proxy type. Syntax: (config-voice-serv-sip)# proxy-type {broadsoft-info|generic| sylantro} Field Definition broadsoft-info Sets the SIP proxy type to BroadSoft. generic Set the SIP proxy type to generic. sylantro Sets the SIP proxy type to Sylantro.
Configuration - Voice Service SIP Mode redundancy advance-timeout redundancy advance-timeout Use the Voice Service SIP redundancy advance-timeout command to set the interval of time before moving onto the next proxy, when the first is not reachable. Syntax: (config-voice-serv-sip)# redundancy advance-timeout number Field Definition number Range 0 - 10 seconds, with a default of 2.
Configuration - Voice Service SIP Mode redundancy rollback-timer redundancy rollback-timer Use the Voice Service SIP redundancy rollback-timer command to set the interval of time between the time the primary proxy fails, and when a rollback is performed back to the primary proxy. To disable rollback timer, see no redundancy rollback-timer command on page 24-10.
Configuration - Voice Service SIP Mode redundancy ttl redundancy ttl Use the Voice Service SIP redundancy ttl command to set the set the SRV Time To Live (TTL) option. The TTL is a set interval of time between flushing the SRV cache. Syntax: (config-voice-serv-sip)# redundancy ttl seconds Field Definition seconds Range 0 - 3600 seconds, with a default of 3600.
Configuration - Voice Service SIP Mode registration registration Use the Voice Service SIP registration command to configure the SIP registration, which allows trunk registration for each user of a PBX. To disable ignore negotiated registration timeout, see no registration ignore-negotiated command on page 24-10.
Configuration - Voice Service SIP Mode session-timer session-timer session-timer mode Use the Voice Service SIP session-timer mode command to configure the timer mode. To disable the timer mode, see no session-timer mode command on page 24-10. Syntax: (config-voice-serv-sip)# session-timer mode {requested|supported} Field Definition requested System shall initiate Session Timer procedures in outgoing initial INVITE’s by including a Session-Expires header.
Configuration - Voice Service SIP Mode sip-port session-timer timeout Use the Voice Service SIP session-timer timeout command to configure the interval of idle time to pass before timeout. Syntax: (config-voice-serv-sip)# session-timer timeout seconds Field Definition seconds Range 90 - 7200 seconds, with a default of 1800.
Configuration - Voice Service SIP Mode transport 24-20 Adit 3000 CLI - Release 1.
INDEX Index A access lan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 access wan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 access-control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 access-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 add user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-59 aggressive-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index C ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ipsec authentication-retries . . . . . . . . . . . . . . . . ipsec key generate key . . . . . . . . . . . . . . . . . . . ipsec log ike . . . . . . . . . . . . . . . . . . . . . . . . . . . ipsec log ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . ipsec vpn_ipsec . . . . . . . . . . . . . . . . . . . . . . . . . net-to-host ipsec . . . . . . . . . . . . . . . . . . . . . . . . net-to-net ipsec . . . . . . . . . . .
Index C trusted-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-58 static-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-58 time-range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-59 username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-59 vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60 vlan port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60 voice-codec . . . . . . . . .
Index C disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . hello-interval . . . . . . . . . . . . . . . . . . . . . . . . . . message-digest-key . . . . . . . . . . . . . . . . . . . . . priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . retransmit-interval . . . . . . . . . . . . . . . . . . . . . transmit-delay . . . . . . . . . . . . . . . . . . . . . . . . . ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . . . ip proxy-arp . . . . . . . . . . . . . .
Index C session-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-20 set-pfs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-20 transform-set . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-21 Configuration-L2TPC do commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2 end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-3 exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index C message-digest-key . . . . . . . . . . . . . . . . . . 11-16 priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-16 retransmit-interval . . . . . . . . . . . . . . . . . . . 11-17 transmit-delay . . . . . . . . . . . . . . . . . . . . . . . 11-17 ip primary-dns . . . . . . . . . . . . . . . . . . . . . . . . . 11-17 ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-17 ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-18 ip secondary-dns .
Index C time-btwn-reconnect . . . . . . . . . . . . . . . . . . 16-19 username . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-19 schedule-availability . . . . . . . . . . . . . . . . . . . . 16-19 shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-19 sip-alg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-20 ppp authentication . . . . . . . . . . . . . . . . . . . . . . . . . 16-21 encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index C ppp authentication . . . . . . . . . . . . . . . . . . . . . . . . . 12-21 encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-21 exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . 12-21 link-fragmentation . . . . . . . . . . . . . . . . . . . . . 12-22 on-demand . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-22 password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-22 restart-timer . . . . . . . . . . . . . . . . . . . . . . . . . .
Index D line enable . . . . . . . . . . . . . . . . . . . . . . . . . . 23-10 line logging . . . . . . . . . . . . . . . . . . . . . . . . . 23-10 output-gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-10 registration enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-11 line authentication . . . . . . . . . . . . . . . . . . . . . . 23-11 line enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-12 line first-phone-number . . . . . . . . . . . . . . .
Index E E early-media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-4 echo-cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-4, 23-5 enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 encapsulation ppp . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-4 encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5 end .
Index M pri . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26 security buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26 notify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 sip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 system buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28 notify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index O ip route . . . . . . . . . 10-21, 11-18, 12-18, 14-17, 16-17 ip secondary-dns . . 10-21, 11-18, 12-18, 14-17, 16-17 ipsec authentication-retries . . . . . . . . . . . . . . . . . . . . 4-37 log ike . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37 log ipsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38 manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-15 replay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38 vpn_ipsec . .
Index R port-protocol-filter . . . . . . . . . . . . . . . . . . . . . . 19-5, 20-5 port-trigger service . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-50 ppp authentication . . . . . 11-21, 12-21, 14-20, 16-21, 17-6 encryption . . . . . . . 11-21, 12-21, 14-20, 16-21, 17-6 exec-timeout . . . . . . . . . . . . . . . . 11-21, 12-21, 14-21 idle-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-21 link-fragmentation . . . . . . . . . . . . . . . . . . 11-22, 12-22 on-demand . . . .
Index S filter-incoming . . . . . . . . . . . . . . . . . . . . . . . . . . 24-14 primary-address . . . . . . . . . . . . . . . . . . . . . . . . . . 24-14 rollback-timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-15 secondary-address . . . . . . . . . . . . . . . . . . . . . . . . 24-15 ttl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-16 type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-16 registration . . . . . . . . . . . . . . . .
Index T static-lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 strip-digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9, 9-7 subnet-mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 T tag-all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-6 tdm-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index W Index - 16 Adit 3000 CLI - Release 1.
