Adit 3200 USER MANUAL Part Number: 770-0156 BA Product Release: 1.
Copyright 2007 Carrier Access Corporation. All rights reserved. The information presented in this manual is subject to change without notice and does not represent a commitment on the part of Carrier Access Corporation. The hardware and software described herein are furnished under a license or nondisclosure agreement. The hardware, software, and manual may be used or copied only in accordance with the terms of this agreement.
PREFACE Preface Compliance Safety of Information Technology Equipment The Adit 3200 is safety certified by Underwriters Laboratories and is compliant with the following safety standards for information technology equipment: UL 60950-1 CSA 60950-1 FCC Requirements, Part 15 This device complies with Part 15 of the FCC Rules.
Preface Compliance The Facility Interface Code (FIC) associated with each private line application represents the type of service that will be provided by the telephone company. The following are currently registered: Port: T1 1.544Mbps T1 1.544Mbps T1 1.544Mbps T1 1.544Mbps FIC: 04DU9-BN 04DU9-DN 04DU9-1KN 04DU9-1SN SOC: 6.0N 6.0N 6.0N 6.
Preface Compliance Industry Canada ICES-003 English This class A digital apparatus complies with Canadian ICES-003. French Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. Industry Canada CS-03 Registration Number: IC: 2638A-675849 This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number.
Preface Safety Information Safety Information CAUTION! ALWAYS USE CAUTION WHEN INSTALLING TELEPHONE LINES. READ THE CAUTIONS BELOW FOR DETAILS ON SAFETY GUIDELINES TO PREVENT INJURY. Never touch uninsulated telephone wires and terminals unless the telephone line has been disconnected at the Network Interface (NI) as voltage potentials as high as 300 VAC may be present across the transmit and receive pairs Only use No.
Preface Electrostatic Discharge (ESD) Precautions Electrostatic Discharge (ESD) Precautions ESD can damage processors, circuit cards, and other electronic components. Always observe the following precautions before installing a system component. 1. Do not remove a component from its protective packaging until ready to install. 2. Wear a wrist grounding strap and attach it to a metal part of the system unit before handling components.
Preface Warranty Warranty Carrier Access warrants to BUYER that Product Hardware will be free from substantial defect in material and workmanship under normal use in accordance with its Documentation and given proper installation and maintenance for period of five years from the date of shipment by Carrier Access.
Preface Warranty Severity 2 issues are failures of the Licensed Software to comply with the Carrier Access software specifications and that result in a major degradation of the Carrier Access Product so as to impact its system or service performance, or significant impairments to network operator control or effectiveness.
Preface Warranty THE WARRANTIES IN THIS AGREEMENT REPLACE ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND ALL OTHER OBLIGATIONS OR LIABILITIES OF CARRIER ACCESS, INCLUDING ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NONINFRINGEMENT AND/OR ANY IMPLIED WARRANTIES ARISING OUT OF COURSE OF PERFORMANCE OR COURSE OF DEALING. ALL OTHER WARRANTIES ARE DISCLAIMED AND EXCLUDED BY CARRIER ACCESS.
TABLE OF CONTENTS Table of Contents Preface Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Safety of Information Technology Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii FCC Requirements, Part 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii FCC Requirements, Part 68 . . . . . . . . . . . . . . . . . . . . .
Table of Contents Compliant Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adit 3104, 3200, 3300 and 3400 Battery Backup . . . . . . . . . . . . . .
CHAPTER 1 Adit 3200 Base Platform In this Chapter Overview Technical Specifications Chassis
Adit 3200 Base Platform Overview Overview The Adit 3200 series IP Business Router is a new breed of access equipment designed to deliver hosted voice and data services at a disruptive price with unmatched performance, engineered to withstand the inherent stress of an enterprise environment. The Adit 3200 integrates the features of a highperformance router and a stateful firewall with flexile WAN interface options.
Adit 3200 Base Platform Technical Specifications Technical Specifications Components Included Accessories - Wall mount bracket Additional Accessories - Adit 3000 Battery Backup Unit - Adit 3000 Rack Mount Kit Interfaces T1 WAN port (RJ-48C connector) - Framing for T1: SF (D4) or ESF - Line Code for T1: B8ZS or AMI - Internal or line-derived clock source - T1 Loop Codes and BERT testing 10/100Base-T WAN port (RJ-45 connector) 4 10/100Base-T switched LAN ports (RJ-45 connector) RS-232 for local management (
Adit 3200 Base Platform Technical Specifications VPN IPSec tunneling and PPTP & L2TP support DES, 3DES and AES IKE-based key management Digital certificates and pre-shared key authentication Router Performance Wire-speed on Ethernet to T1 interface Quality of Service ToS marking and interpretation per IETF Std.
Adit 3200 Base Platform Technical Specifications Regulatory Approvals USA UL60950 FCC Part 15, Class A FCC Part 68 Canada CSA 60950-1 ICES-003, Class A CS-03 Physical Information Wall mount brackets (included) Rack mount options: 19 or 23 inch rack Dimensions: 1.75 in. (H-2 RU) x 8.25 in. (W) x 12 in. (D) 4.4 cm (H) x 21 cm (W) x 30.5 cm (D) Weight: 6.25 lbs. (2.
Adit 3200 Base Platform Chassis Chassis Front (4) 10/100Base-T Ethernet (LAN) Alarm Status Reset (1) DS1/E1 (WAN) (E1-future) (1) 10/100Base-T Ethernet (WAN) Back Ground 1-6 Power/Battery/Status RS-232 Management Port Adit 3200 - Release 1.
CHAPTER 2 Physical Installation In this Chapter Unpacking and Inspection Installation Environment Compliant Installation Wall Mounting Rack Mounting Adit 3104, 3200, 3300 and 3400 Battery Backup
Physical Installation Unpacking and Inspection Unpacking and Inspection WARNING! OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES. 1. Inspect containers for damage during shipment. Report any damage to the freight carrier for possible insurance claims. 2. Compare packing list with office records. Report any discrepancies to the office. 3. Open shipping containers, be careful not to damage contents. 4. Inspect contents and report any damage. 5.
Physical Installation User Safety User Safety CAUTION! WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING THE FOLLOWING: Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using a telephone (other than a cordless type) during an electrical storm.
Physical Installation Compliant Installation NOTE: It is important the DS1/E1 Network Interface Cables are secured separately from the power and Signal Cables. 1. Inspect the unit. 2. Mount the unit, see Wall Mounting on page 2-5, or Rack Mounting on page 2-6 for detailed instructions. 3. Ground the unit. WARNING! THE SEPARATE PROTECTIVE EARTHING TERMINAL PROVIDED ON THIS PRODUCT SHALL BE PERMANENTLY CONNECTED TO EARTH. SEE GROUNDING THE UNIT ON PAGE 3-3. 4.
Physical Installation Wall Mounting Wall Mounting Before beginning the mounting process, verify that the installation area is a stable environment, clean and free from extremes of temperature, shock, vibration and EMI. See Installation Environment on page 2-2.
Physical Installation Rack Mounting Rack Mounting NOTE: Rack mounting kits are available for both 19 and 23 inch racks. 1 Rack Unit (RU) of spacing is required above the Adit 3000 in the Rack Mount Unit. To rack mount the Adit 3000, follow the instructions below: 1. Attach bracket ears to Rack Mounting Tray using four #10-32 x 1/4” screws on each side. The Mounting Ears can be used for both a 19 or 23 inch rack. The drawing below shows a top view of the 2 versions.
Physical Installation Rack Mounting 4. Place the Adit on the Tray Slide and attach with 4 screws removed in step 2. screws screws Tray Slide 5. Slide the assembled piece (Adit 3000 and Tray Slide) onto the installed Rack Mounting Tray. 6. Secure the Tray Slide to the Rack Mounting Tray with the attached screws on the Tray Slide. Adit 3200 - Release 1.
Physical Installation Adit 3104, 3200, 3300 and 3400 Battery Backup Adit 3104, 3200, 3300 and 3400 Battery Backup The Adit 3104, 3200, 3300 and 3400 Battery Backup (P/N 730-0132), is a wall-mount battery backup unit to provide up to 8 hours battery backup. Please see the Battery Backup User Manual for product information and installation instructions, which is provided with unit. Note: This is an optional feature. 2-8 Adit 3200 - Release 1.
CHAPTER 3 Electrical Installation & Cabling In this Chapter Adit 3200 Interface Connectors Reset Button Alarm/Status LEDs
Electrical Installation & Cabling Adit 3200 Adit 3200 Connections The following illustrations show all connectors on the Adit 3200. Front Alarm Status (4) 10/100Base-T Ethernet (LAN) Reset (1) DS1/E1 (WAN) (E1-future) (1) 10/100Base-T Ethernet (WAN) Back Ground 3-2 Power/Battery/Status RS-232 Management Port Adit 3200 - Release 1.
Electrical Installation & Cabling Interface Connectors Interface Connectors The following are the Adit 3200 interface connectors: Front of Adit (1) DS1 WAN port (RJ-48C). Note: E1 will be in a future release.
Electrical Installation & Cabling Interface Connectors Power The Adit 3000 is powered by a limited -48 VDC Power source. The following options are available: AC/DC Converter Battery Backup module AC/DC Converter An AC/DC Converter generates 48VDC from any worldwide AC power source. To connect AC power: 1. Plug power connector from AC/DC converter into rear of Adit 3000. 2. Connect AC/DC converter to wall outlet. 3. A green light should appear on the Status LED on the front of the unit.
Electrical Installation & Cabling Interface Connectors RS-232 Craft Port (Female DB-9) The RS-232 craft port connector (female) is for connection to an external PC or Hayes-compatible modem for local or remote configuration, management, and performance monitoring using the Adit 3000 Command Line Interface (CLI). The RS-232 craft port connects via a female DB-9 connector on the Adit 3000.
Electrical Installation & Cabling Interface Connectors DS1/E1 Connection Ports Each DS1/E1 connection port is equipped with a standard RJ-48C (female) on the Adit 3000 unit. Note: E1 will be available in a future release.
Electrical Installation & Cabling Interface Connectors 10/100Base-TX Ethernet The 10/100Base-TX Ethernet (female) ports provide connectivity for Router WAN and/or LAN ports and for management connection via Telnet and/or SNMP to a Network Management System. 1 8 8 Ethernet (RJ-45) 1 The pinouts are as follows: Note: This is a hub pinout, you will need a straight cable to connect to a PC.
Electrical Installation & Cabling Reset Button Reset Button The system can be reset by pressing the reset button located on the front panel. Alarm/Status LEDs LED State Description Critical Off No critical alarms present Red Critical alarms present. Critical alarms include: user-configured manor environmental inputs. Off No major alarms present Red Major alarm present.
CHAPTER 4 Configuration After the Adit 3200 is installed (see Compliant Installation on page 2-3), the system can now be provisioned.
Configuration PC Network Configuration PC Network Configuration When a PC is connected directly or indirectly to the Adit 3200 Ethernet LAN port (Eth-1), IP addresses will be acquired using the DHCP server or relay functionality of the Adit 3200. Note: For either of these cases, the PC must be configured as a DHCP Client. This configuration principle is identical but performed differently on each OS. Windows XP 1. Access Network Connections from the Control Panel. 2.
Configuration PC Network Configuration Linux 1. Login into the system as a super-user, by entering su at the prompt. 2. Type ifconfig to display the network devices and allocated IP’s. 3. Type pump -i dev, the dev is the network device name. 4. Type ifconfig again to view the new allocated IP address. 5. Continue on the following setup for a LAN Connection. LAN Connection Your computer can connect to the gateway in various forms, each requiring a different physical connection.
Configuration Web-Based Management Web-Based Management The web-based management interface allows you to control various system parameters. The interface is accessed through a web browser. To access the management console NOTE: The following assumes that you have connected the PC to the LAN port of the Adit 3200. 1. Launch a web browser on your PC in the LAN to which the Adit 3200’s LAN port is connected.
Configuration Setting up a CLI Connection Setting up a CLI Connection A CLI connection will require the LAN or WAN IP address of the unit. Note: If the WAN IP address is used, the remote admin WAN access must be enabled with the following command sequence: Command Username: admin Description Log into the system (username and password). Password: ******** Adit 3200> enable Enter the Privileged mode. Password: ******** Enter password for the Privileged mode.
Configuration Log in Log in After successful connection, via telnet or HyperTerm, the user must login. Default Logins are: Login: admin Password: admin123 After successful login the prompt will be displayed as follows: Adit 3200> Note: It is recommended that you change your password from the default. See the following to modify the Admin level password on your system. GUI interface - see Advanced/Users window CLI interface - use the Adit 3000(config)#username command 4-6 Adit 3200 - Release 1.
Configuration Key Enabled Software Features Key Enabled Software Features The Adit 3200 has additional features that are not provided on the base system. These features can be purchased with the product or added later as needed. These features are enabled via a Software Key (example: G.729). The number of keyed features may expand with the development of the product, therefore to see a list of current keyed features, or to purchase a key, contact Carrier Access Customer Service or Sales.
Configuration Basic Configuration Basic Configuration The following configuration is divided into logical sections, where each section configures an additional function. The first must be configured before the second and so forth, however, you may stop at any section and not add the following feature. NOTE: The order in which commands are entered can affect the successful provisioning of the Adit 3200.
Configuration Basic Configuration Restore Factory Defaults If the unit is not out-of-the-box, you may want to verify that the unit is set to defaults. Note: This will reset the IP address back to the default setting of 192.168.1.1. In the web-browser: Select Advanced from the Navigation bar Select Restore Defaults Select OK to restore defaults Adit 3200 - Release 1.
Configuration Basic Configuration Modify Default Admin User For security purposes it is recommended that the Administrator User be changed from the default settings. Modify the Administrator User in the web-browser: Select Advanced from the Navigation bar Select Users icon Select Administrator, to open the profile. 4-10 Adit 3200 - Release 1.
Configuration Basic Configuration Modify the User information, and select OK to save. It is important to note that you need to have a minimum of one user with Administrative Privileges. For users with other access levels, add a New User. Note: For security purposes, the password should be changed. You will be required to login again, if you have modified the User Profile that you are logged in with. Adit 3200 - Release 1.
Configuration Basic Configuration Configure Ethernet WAN Interface In the web-browser: 1. Select Network Connections from the Navigation bar. 2. It is recommended that you disable/delete the Serial1 port. 3. Select (click) Ethernet 2 (WAN Ethernet) connection to configure. 4. Select the Enable button, to configure the WAN Ethernet up (or in-service). 5. Select the Settings button. 4-12 Adit 3200 - Release 1.
Configuration Basic Configuration 6. Set Internet Protocol to Obtain an IP Address Automatically, from the pulldown menu. This will enable the Adit 3200 as a DHCP Client. Leave the other fields to their default settings. 7. Select Apply to apply the new settings. Adit 3200 - Release 1.
Configuration Basic Configuration Configure Serial 1 as WAN In the web-browser: 1. Select Network Connections from the Navigation bar. 2. Select Serial 1. 3. Select Settings button. 4. Set Network to WAN. 5. Select Apply to apply the new settings. 4-14 Adit 3200 - Release 1.
Glossary AMI Automatic Mark Inversion ARP Address Resolution Protocol B8ZS Bipolar with 8 Zero Substitution BIT Binary Digit BPS Bits Per Second BPV Bipolar Violation CA Certificate Authority CAS Channel Associated Signaling CCS Common Channel Signaling CHAP Challenge Handshake Authentication Protocol CID Caller ID CIDR Classless Inter-Domain Routing CLASS Custom Local Area Signaling Service CLEI Common Language Equipment Identification CLI Command Line Interface CO Central O
Glossary DLCI DLCI Data Link Connection Identifier DMZ Demilitarized Zone DNS Domain Naming System DS0 Digital Signal Level Zero (64 kbps) (1 voice channel) DS1 Digital Signal Level 1 (1.
Glossary NAT NAT Network Address Translation NCS Network-based Call Signaling NEBS Network Equipment Building Standards NRZ Non-Return to Zero NSE Named Service Event NTP Network Time Protocol OSPF Open Shortest Path First PAP Password Authentication Protocol PHY Physical specifications POTS Plain Old Telephone Service PPP Point-to-Point Protocol PRI Primary Rate Interface PVC Permanent Virtual Circuit QoS Quality of Service RADIUS Remote Authentication Dial-In Service SABME S
Glossary WAN WAN Wide Area Network WINS Windows Internet Naming Service Glossary-4 Adit 3200 - Release 1.
Glossary 10Base-T 10Base-T The most widely installed Ethernet local area networks (LANs) use ordinary telephone twisted-pair wire. When used on Ethernet, this carrier medium is known at 10BASE-T. 10BASE-T supports Ethernet’s 10 Mbps transmission speed. 100Base-TX Also called “Fast Ethernet”, it is a 100 Mbps version of Ethernet. 100Base-T transmits at 100 Mbps rather than 10 Mbps. Like regular Ethernet, Fast Ethernet is a shared media LAN. All nodes share the 100 Mbps bandwidth.
Glossary channel channel A generic term for a communications path on a given medium; multiplexing techniques allow providers to put multiple channels over a single medium. Channel Associated Signaling (CAS) Carrying signaling information within the data channels of a T1 line (in band) rather than on a separate control channel. CAS signaling is also used to carry 911 emergency data such as telephone number and location information.
Glossary Electro-magnetic Interference (EMI) Electro-magnetic Interference (EMI) Equipment used in high speed data systems, including ATM, that generate and transmit many signals in the radio frequency portion of the electromagnetic spectrum. Interference to other equipment or radio services may result if sufficient power from these signals escape the equipment enclosures or transmission media. National and international regulatory agencies (FCC, CISPR, etc.) set limits for these emissions.
Glossary gateway gateway An entrance and exit into a communications network Graphical User Interface (GUI) GUI, pronounced “GOOEY”. A set of screen presentations and metaphors that utilize graphic elements such as icons in an attempt to make an operating system easier to use. ground A physical connection to the earth or other reference point.
Glossary Local Area Network (LAN) Local Area Network (LAN) A short distance data communications network (typically within a building or campus) used to link together computers and peripheral devices under some form of standard control. Line Build Out (LBO) T1s require the last span to lose 15 - 22.5 dB, a selectable output attenuation is generally required of DTE equipment. Line Coding Violation (LCV) This parameter is a count of both BPVs and EXZs occurring over the accumulation period.
Glossary modem modem MOdulator-DEModulator, a device that takes digital computer signal, converts it to analog, and sends it across the phone line. Another modem on the reverse does the exact opposite action. Modems transfer data at different speeds or rates, called baud. multiplexer Electronic equipment which allows two or more signals to pass over one communications circuit. The circuit may be analog or digital MUX See multiplexer NetBIOS Network Basic Input/Output System.
Glossary PPP PPP Point-to-Point Protocol. is used for establishing a point-to-point link that provides a single, preestablished WAN communications path from the customer premises, through a carrier network (the telephone company), to a remote network PPPoT1 Point-to-Point over T1. PRACK Provisionable acknowledgement. Primary Rate Interface (PRI) The ISDN equivalent of a T1. The Primary Rate Interface (delivered to the customer’s premise) provides 23B+D (N.America) or 30B+D (Europe) running at 1.
Glossary SAP SAP Service Access Point. signal A generated electrical impulse that is a change in voltage to trigger an event. Simple Network Management Protocol (SNMP) SNMP is the most common method by which network managements applications can query a management agent using a supported MIB (Management Information Base). SNMP operates at the OSI application layer.
Glossary Wide Area Network (WAN) Wide Area Network (WAN) A private long distance network that uses leased lines to connect computers or LANs. A wide area network is a linking of computers not physically attached through conventional network connectivity. Usually the WAN connection is a dedicated or high grade dial up phone link. It is often done with T1 or T3 connections but can also be through satellite or other technologies. WINS Windows Internet Naming Service.
Glossary Virtual Local Area Network (VLAN) Glossary-14 Adit 3200 - Release 1.
INDEX Index Numerics 100Base-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 A operating altitude . . . . . . . . . . . . . . . . . . . . . . . . . . operating temperature . . . . . . . . . . . . . . . . . . . . . . . relative humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . connector pinout . . . . . . . . . . . . .
Index N N non-operating altitude . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 O operating altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 P PC Network Configuration . . . . . . . . . . . . . . . . . . . . . Physical Information . . . . . . . . . . . . . . . . . . . . . . . . . . pinouts DB-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RJ-48C . . . . . . . . . .
