Owner’s Manual

8 Specifications subject to change without notice. OM-40MAQ-07
Timer Function
TIMER ON (to start the unit) and TIMER OFF (to stop the unit) can
be used separately or together.
Timer ON Only
This function allows the unit to start automatically at the set time. The
TIMER ON function can be set while the unit is on or off.
UNIT ON
1. Press TIMER ON to initiate the auto-on time sequence. The set
time is displayed in the remote control display. Every time TIMER
ON is pressed, the time increases by 30 minutes, up to 10h. It
increases by 60 minutes, afterwards, until the time setting reaches
24h. When the TIMER ON is set, the TIMER light on unit
illuminates. The unit continues to run at the set time.
UNIT OFF
1. Set the timer described in the UNIT ON section. The unit starts at the
set time.
2. Adjust the TIMER ON settings to 0.0 to cancel this option.
Timer OFF Only
This function allows the unit to stop automatically at the set time. The
timer can be set while the unit is on or while it is off.
UNIT ON
1. Press TIMER OFF to initiate the auto-off time sequence. The
set time appears on the remote control display. Every time TIMER
OFF is pressed, the time increases by 30 minutes, up to 10h. It
increases by 60 minutes, afterwards, until the time settings reach
24h. When the TIMER OFF is set, the timer light on the unit
illuminates and the unit turns off automatically at the set time.
UNIT OFF
1. Set the TIMER OFF as described in the UNIT ON section. The
TIMER display on the unit illuminates and the unit remains off.
2. Adjust the TIMER ON settings to 0.0 to cancel this option.
Timer ON and Timer OFF
Use both functions to program the unit to turn on and shut off at
specified times.
UNIT ON
1. Set TIME OFF as previously described.
2. Set TIME ON as previously described. The unit turns off
automatically at the set TIME OFF and turns on at the set TIME
ON.
UNIT OFF
1. Set TIMER ON as previously described.
2. Set TIMER OFF as previously described. The unit starts
automatically at the set TIME ON and turns off at the set TIME
OFF.
SLEEP Mode
SLEEP mode is used to conserve energy and can be used when the
unit is in the COOL, HEAT or AUTO mode only.
Fig. 12 — Sleep Mode
COOLING Mode
1. Push SLEEP. After 1 hour the set point raises by 1.8°F (1°C). After
another hour, the set point raises by another 1.8°F (1°C) and the fan
runs in a low speed. The unit shuts off 5 hours after setting the
SLEEP mode. SLEEP mode cancels if either MODE, TEMP,
FAN, TIMER, or ON/OFF on the remote control is pressed.
HEATING Mode
Same as the COOLING mode however the set points are lowered by
1.8°F (1°C).
TURBO Mode
Use TURBO to cool or heat the room rapidly.
1. Press TURBO. An audible “beep” is heard if the indoor unit
supports this function. The fan runs on super high speed. The
TURBO mode terminates automatically 20 minutes after selecting
TURBO.
2. To cancel TURBO, select TURBO mode again. When the
TURBO mode terminates, the unit reverts to the original setting.
SELF CLEAN Mode
1. Press CLEAN to activate or deactivate the self-cleaning function.
Under this function, the air conditioner automatically cleans and
dries the evaporator. The cleaning cycle takes 30 minutes, after
which the unit turns off automatically. The unit operates in the
following sequence:
•FAN ONLY mode at LOW fan speed
•HEATING operation with LOW fan speed
•FAN ONLY operation
•Stop Operation
•Turn off
2. To cancel the CLEAN mode, press CLEAN. The operation ends
and the unit turns off. This function can be activated only in the
COOL or DRY modes. Before selecting this function, it is
recommended to run the air conditioner under COOLING
operation for about half an hour. Once the SELF CLEAN function
is activated, all timer settings will cancel.The indoor unit displays
SC.
NOTE: The SELF CLEAN mode is available ONLY on the single
zone models.
TIMER
ON
TIMER
OFF
Set
temperature
1hr
1hr
7 hours
timer o
+/- 1 C/2 F
SLEEP Operation
+/- 1 C/2 F
Saving energy during sleep
TIMER
ON
ON/OF F
ON/OF F
TIMER
OFF
ON/OF F
ON/OF F
TIMER
ON
TIMER
OFF
ON/OF F
ON/OF F
SLEEP
TURBO
CLEAN