Installation Instructions

ManualsBrandsCarrier ManualsOther40MBFQ123

40MBFQ

Floor Console Ductless System

Sizes 09 to 58

Installation Instructions

NOTE: Read the entire instruction manual before starting the

installation.

NOTE: Image for illustration purposes only. Actual model may be

slightly different.

TABLE OF CONTENTS

PAGE

SAFETY CONSIDERATIONS 2.........................

PARTS LIST 3.......................................

SYSTEM REQUIREMENTS 4...........................

WIRING 4...........................................

DIMENSIONS 5......................................

CLEARANCES 7.....................................

INSTALLATION LOCATION REQUIREMENTS 7..........

INDOOR UNIT INSTALLATION CONSOLE SIZE 12 7......

INDOOR UNIT INSTALLATION CONSOLE SIZES 18−58 9..

INTERCONNECTING PIPING 9.........................

ELECTRICAL DATA 11...............................

CONNECTION DIAGRAMS 11.........................

WIRELESS REMOTE CONTROL INSTALLATION 12......

WIRED REMOTE CONTROL INSTALLATION 12..........

START−UP 12........................................

TROUBLESHOOTING 13..............................

Summary of content (14 pages)

PAGE 1
40MBFQ Floor Console Ductless System Sizes 09 to 58 Installation Instructions TABLE OF CONTENTS PAGE SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . 2 PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SYSTEM REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
SAFETY CONSIDERATIONS Installing, starting up, and servicing air−conditioning equipment can be hazardous due to system pressures, electrical components, and equipment location (roofs, elevated structures, etc.). Only trained, qualified installers and service mechanics should install, start−up, and service this equipment. Untrained personnel can perform basic maintenance functions such as cleaning coils. All other operations should be performed by trained service personnel.
PAGE 3
PARTS LIST 3 1 1 5 5 D. Connecting point of refrigerant pipe 2 (D. gas side) 1 Drain point 7 E. Connecting point of refrigerant pipe ON MO /O 6 FF DE (E.
PAGE 4
SYSTEM REQUIREMENTS Allow sufficient space for airflow and servicing unit. Piping IMPORTANT: Both refrigerant lines must be insulated separately. S Minimum refrigerant line length between the indoor and outdoor units is 10 ft. (3 m). S Table 2 lists the pipe sizes for the indoor unit. Refer to the outdoor unit installation instructions for other allowed piping lengths and refrigerant information. Table 2—Indoor Unit Pipe Sizes 9K 12K 18K 24K 36K 48K 58K Gas Pipe in(mm) 3/8 (9.52) 1/2 (12.
PAGE 5
23.62(600) DIMENSIONS 8.27(210) 27.56(700) Hanging arm 7.68(195) 0.63(16) Drain pipe Unit: in (mm) Fig. 2 - Indoor Unit Sizes 09−12 Table 3—Indoor Unit Sizes 09−12 UNIT SIZE Depth Width Height Weight-Net 9 8.27 (210) 27.56 (700) 23.62 (600) 32.41 (14.7) in. (mm) in. (mm) in. (mm) Lb (kg.) 5 12 8.27 (210) 27.56 (700) 23.62 (600) 32.41 (14.
PAGE 6
4.7in (120mm) Outside Air Intake 1.3in (33mm) 5.5in (140mm) 8.0in (204mm) 1.57in (40mm) 3.7in (94mm) DIMENSIONS (CONT) 8.7in (222mm)/ 8.6in (220mm) 4.7in (120mm) Fig. 3 - Indoor Unit Sizes 18−58 Table 4—Indoor Unit Sizes 18−58 UNIT SIZE Height Width Depth Weight-Net in(mm) in(mm) in(mm) lbs(kg) 18K 9.25(235) 42.05(1068) 26.57(675) 55.12(25) 24K 9.25(235) 42.05(1068) 26.57(675) 58.42(26.5) 36K 9.25(235) 50.59(1285) 26.57(675) 69(31.3) 6 48K 9.25(235) 64.96(1650) 26.57(675) 83.78(38) 58K 9.
PAGE 7
CLEARANCES Fig.
PAGE 8
INSTALLATION LOCATION REQUIREMENTS S A location where there are no obstacles near inlet and outlet area. S S A location which can bear the weight of indoor unit. S A location which provides appropriate clearances as outlined in Fig. 5. INDOOR UNIT PREPARATION 1. Open the Front Panel sliding the two stoppers towards the middle of the indoor unit (see Fig. 7). Do not install indoor units near a direct source of heat such as direct sunlight or a heating appliance.
PAGE 9
INDOOR INSTALLATION CONSOLE SIZES 18−58 1. The mounting hooks should be located horizontally and level on the wall or vertical on the ceiling. All minimum clearances should be maintained. 2. Remove the side boards and the grille (see Fig. 10). Hanging screw bolt Hanging arm Fig. 14 - Wall mount installation Side board DRILL A HOLE IN THE WALL FOR THE INTERCONNECTING PIPING, DRAIN AND WIRING Grille Fig. 10 - Remove the side boards and the grille 3. Locate the hanging arm on the hanging screw bolt (Fig.
PAGE 10
Handle Bar Bar Yoke Cone CONDENSATE DRAIN CONNECTION The unit is supplied with a drain connection to connect the drain piping. When installing condensate piping, follow these recommendations: S Condensate piping should slope downward in the direction of the condensate flow, with a minimum gradient of 1 in. per 100 inches. S When multiple units are connected to a common condensate drain, ensure the drain is large enough to accommodate the volume of condensate from all units.
PAGE 11
ELECTRICAL DATA Table 7—Electrical Data Console and Floor Ceiling Size FLA Input W Rated HP HP 09K (208/230V) 0.21 66.6 0.027 12K (208/230V) 0.21 66.6 0.027 18K (208/230V) 1.11 100 0.075 24K (208/230V) 1.11 100 0.075 36K (208/230V) 1.36 130 0.156 48K (208/230V) 0.94 98 0.122 58K (208/230V) 1.2 210 0.218 LEGEND FLA - Full Load Amps CONNECTION DIAGRAMS Fig. 23 - Connection Diagrams 09 to 24 Fig. 24 - Connection Diagrams 36 and 58 Fig. 25 - Connection Diagram Notes: 1.
PAGE 12
WIRELESS REMOTE CONTROL INSTALLATION Mounting Bracket (if installed on the wall) 1. Use the two screws supplied with the control to attach the mounting bracket to the wall in a location selected by the customer and within operating range. 2. Install the remote control batteries. 3. Place the remote control into the remote control mounting bracket. NOTE: For remote control operation, refer to the unit owner’s manual.
PAGE 13
TROUBLESHOOTING For ease of service, the systems are equipped with a diagnostic code display LEDs on both the indoor and outdoor units. The indoor diagnostic display is a combination of flashing LEDs on the display panel or the front of the unit. Some indoor units display error codes specifying failure modes in outdoor units. If possible, always check the diagnostic codes displayed on the indoor unit first. The diagnostic codes displayed in the indoor and outdoor units are listed in Table 8.
PAGE 14
Copyright 2018 CAC / BDP D 7310 W. Morris St. D Indianapolis, IN 46231 Edition Date: 10/18 Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.