Ceiling Fan Smart Switch User Manual SMART LIFE STAYS IN MOTION
General Specifications Model PN-04F02D FCC ID 2ANDL-WBR3 Power Supply AC 120V Rated Frequency 60Hz Max. Current Fan: 1.5A Light: 2.5A Max. Power 400W/gang Wireless Standard WiFi 2.4GHz WIFI IEEE 802.11b/g/n Installing your switch 1 Turn power off at circuit breaker! WARNING – SHOCK HAZARD May result in serious injury or death. Turn off power at circuit breaker or fuse before installing. If you are unsure or uncomfortable about performing this installation, consult a qualified electrician.
2 Wiring Switch. White: Neutral (Supplied) Black: Live Bare copper or Green: Ground Red: Load (Light) Orange: Electric Fan Electric Fan Light Note: Make sure all the wires are connected with the correct colors as shown above.
Take out the white wire and wiring cap from the screw bag . Stick this white wire to the switch using the provided screw. Then connect tightly the white wire to the Neutral wire from the wall by wiring cap. (If the length of Neutral wire from the wall is long enough, connect it to the switch directly.) Connect tightly the remaining wires from the wall to the switch by the provided screws as per the above wiring diagram.
Installation of the Smart Switch is now completed. Turn the circuit breaker back on.
5 Switch can be assembled in several. Switch can be combined in 2gang, 3gang, or 4gang boxes. The buttons and switch can be seamlessly connected together, which fully conforms to the size of the home switchbox.
Operation Fan On/Off Light On/Off ON/OFF ON/OFF Fan Speed Up Light High Fan Speed Down Light Low Sleep Breeze Night Light MINI Pair Function,press and hold button for 5 Seconds to retry switch and App connection. Fan Indicator Light Turns the power to fan off. Speeds up the fan. Presses to get the light brighter. Speeds down the fan. Presses to make the light dimmer. There are three gears of wind speed. MINI Turns the light on and off.
NOTE:If the fan indicator light is blinking then the switch is ready to pair with the App. If you are unable to pair smart switch with App, press and hold "CARRO"button for 5 Seconds until LED indicator light starts blinking slowly on switch button to pair with App again. The fan indicator light is red when you fail to connect smart switch to App, and green when the connection is finished. Cleaning: Clean with a damp cloth. DO NOT use chemical cleaners.
APP control Connection (Wifi and Bluetooth): 1. First download the free Carro Home app from the App Store or Google Play or scan the QR Code as below. 2. Open the Carro Home app to create your account. The account with “Carro Home” can be registered through E-mail or Mobile phone. 3. Connect the device to the Carro Home app (Four ways connection): ① Bluetooth connect (WIFI & Bluetooth on) a. Press “+” button into the device list, then a window will pop up to show you some devices can be connected. b.
Smart switch: Press and hold the “CARRO” button for 5 seconds till the indicator light blinking slowly to into AP Mode. b. Press “+” button to select “Electrical”(smart switch) or “Air Circulation” (smart ceiling fan) on the sidebar menu then select “Ceiling Fan Switch” or “Ceiling Fan” and tap next. c. Connect to your home WIFI (Only for 2.4Ghz). d. Choose AP Mode. e. Press “Next” button to go to connect the fan’s WIFI signal. f. Choose the fan’s WIFI signal “CarroHome-XXXX” then back to the app. g.
Troubleshooting Symptom Solution Fan and light do not turn ON and no indicator lights turn ON. • Ensure Front Accessible Service Switch (FASS) is fully pushed in to the ON position. • Ensure both fan and light pull chain are set to highest possible setting. • Light bulb(s) burned out and the fan is in the off position. Ensure fan is in the highest speed setting and replace light bulbs as needed. • Light is not properly installed. • Breaker is OFF or tripped (or fuse blown). Reset breaker or replace fuse.
FCC/IC Information This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Carro USA Inc. could void the user’s authority to operate this equipment.
