Carry Technology ComWi Quick Guide ComWi (DW06) Quick Guide Copyright © 2011, Carry Technology Co., Ltd.
Carry Technology ComWi Quick Guide Table of Content Chapter 1: Introduction ………………………………..……….2 1.1 Introduction ……..………………………………………………....2 1.2 Hardware Features ……..………………………………………………....3 1.3 Software Features ……..………………………………………………....4 1.4 Package Contents ……..………………………………………………....4 Chapter 2: Hardware Installation ………………………...…….5 2.1 How to install Network function ……………..……..…….……5 2.2 How to start reader and charger function ……………..……..…….……5 2.
Carry Technology ComWi Quick Guide Chapter 1: Introduction 1.1 Introduction Thank you for purchasing the ComWi for your iPad accessory. The ComWi Wi-Fi travel router is designed for use with tablets, smart phones, and handheld electronic wireless devices. The ComWi can be powered by power adapter of iPad, can conveniently connect to the internet and share the connection around an average sized room at 150Mbps.
Carry Technology ComWi Quick Guide 1.2 Hardware Features Standard Wireless LAN Antenna Interface Frequency Range Number of Selectable Channels Data Rate Coverage Area LED IEEE 802.11b/g/n standards compliant 1T1R Mode (150Mbps) Internal PIFA 2 dBi antenna • USB Type-A Plug for iPad Power Adapter • USB Type-A Receptacle for iPad Charger • RJ45 (WAN Port) • Reset (3Sec) button 2.250 ~ 2.4835 GHz (subject to local regulations) 802.11n 20MHz/25MHz 802.11b/g USA, Canada (FCC): 11 channels (2.412GHz ~2.
Carry Technology ComWi Quick Guide 1.3 Software Features WAN Networking Wi-Fi • DHCP Client • Static IP • PPPoE (for ADSL…) • PPTP • L2TP • DHCP Client/Server • Dynamic DNS • 1 Transmit and 1 Receive paths (1T1R) • 20MHz/25MHz bandwidth • Support different SSID • Support Hidden SSID • Support WPS • Support WDS / WiFi Repeater Mode • High security supported: WEP64/128, WPA, WPA2 AES, WPA2 Mixed • Support QoS 1.
Carry Technology ComWi Quick Guide Chapter 2: Hardware Installation 2.1 How to install Network function After you unpack the box, please make sure all the components are completed. Follow the below steps to setup the ComWi: 1. Connect USB Type-A Plug to iPad Power Adapter. 2. Connect the Ethernet cable to the ComWi WAN port 3. Connect the other end of the Ethernet cable to the ADSL 2.2 How to start iPad charger function Follow the below steps to enable iPad Charger function: 1.
Carry Technology ComWi Quick Guide 2.3 Interface & LED Indicators Description iPad Power Adapter Hole LED USB Type-A Receptacle WAN (RJ-45) 1. PWR LED (Green): Indicates ComWi is Power On for Wi-Fi mode. 2. Wi-Fi LED (Red): Indicates the Wireless LAN is keeping in working stage.
Carry Technology ComWi Quick Guide 3. Reset (3Sec) button under the Hole: First, please make sure you had powered on the Wi-Reader and Wi-Fi LED (Red) is keeping in working stage, then you can use a kit to press the Reset button. After pressing 3 seconds, you will see Wi-Fi LED (Red) will turn off. Currently, you can release the button for recovering it to Default Network setting.
Carry Technology ComWi Quick Guide Chapter 3: Wireless and Network Setup This chapter is to describe how to configure Network of ComWi. If you don’t want to update any Network setting, please skip this Chapter (Chapter 3). 3.1 Default Network setting for ComWi IP address 10.10.1.1 Subnet mask 255.255.255.0 Username OFF Password OFF Operation Mode Gateway DHCP Server Mode SSID ComWi Channel Auto Security OFF 3.
Carry Technology ComWi Quick Guide 2. Choose a Wi-Fi Network: “ComWi_xxxxxx” 3. Open iPad / iPhone Native Browser – Safari 4. Enter: http://10.10.1.
Carry Technology ComWi Quick Guide 5. Refer to the following Web U/I and click “Next”.
Carry Technology ComWi Quick Guide 6. LAN Interface Setup The following figure is to show how to configure the parameters for local area network connected to the ComWi. If you don’t want to update LAN Interface Setup, please click “Next” directly to skip it.
Carry Technology ComWi Quick Guide 7. WAN Interface Setup For Example: Select PPPoE for ADSL on WAN interface. User Name and Password need to be done and click “Next”. If there is no ADSL network for connecting WAN Port of ComWi, you can keep it in “DHCP Client” and click “Next” directly to skip it.
Carry Technology ComWi Quick Guide 8. Wireless Basic Settings for using different SSID for your ComWi. After updating it, please click “Next” directly.
Carry Technology ComWi Quick Guide 9. Wireless Security Setting The following figure is to show setting up the security of the ComWi. Turning on the ComWi security will prevent any unauthorized access to the wireless network and. After updating it, please click “Finished” and wait about 20 second for accessing your New SSID.
Carry Technology ComWi Quick Guide 10. Upgrade Firmware The feature allows ComWi firmware to be upgraded to a new version. Please refer to the following figure for updating firmware. It shows the current Firmware version. Select the latest firmware file from the local system like PC/Notebook and click “Upload”. NOTE: DON’T TURN OFF THE POWER DURING THE UPLOAD FIRMWARE. FAILURE WILL DAMAGE ComWi. 15 FCC Compliance and Advisory Statement This device complies with Part 15 of the FCC rules.
