† † pxm250/450/900 Professional Stereo Power Amplifier Made In America 8100.0157A †Available in North America only A Division Of Phoenix Gold International, Inc. 9300 North Decatur ● Portland OR 97203 ● Tel: 503.288.2008 ● Fax: 503.978.3302 ● Email: carverpro@imagina.
Introduction Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated"dangerous voltage" within the product's enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Introduction Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated"dangerous voltage" within the product's enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons.
PXm250 • 250W bridged mono into 8 ohms 175W per channel into 2 ohms 125W per channel into 4 ohms 75W per channel into 8 ohms • Three connector versions available: Standard - XLR and 1/4" TRS inputs with Multi-way Binding Posts BR Version - Barrier Strip inputs with Multi-way Binding Posts SP Version - XLR and 1/4" TRS inputs with Neutrik™ Speakons™ • Independent level controls for CH1 & CH2 • Independent CH1 and CH2 switchable High Pass Filters, selectable at 30Hz or 80Hz • Independent CH1 and CH2 selec
PXm250 • 250W bridged mono into 8 ohms 175W per channel into 2 ohms 125W per channel into 4 ohms 75W per channel into 8 ohms • Three connector versions available: Standard - XLR and 1/4" TRS inputs with Multi-way Binding Posts BR Version - Barrier Strip inputs with Multi-way Binding Posts SP Version - XLR and 1/4" TRS inputs with Neutrik™ Speakons™ • Independent level controls for CH1 & CH2 • Independent CH1 and CH2 switchable High Pass Filters, selectable at 30Hz or 80Hz • Independent CH1 and CH2 selec
PXm450 • 450W bridged mono into 8 ohms 275W per channel into 2 ohms 225W per channel into 4 ohms 150W per channel into 8 ohms • Three connector versions available: Standard - XLR and 1/4" TRS inputs with Multi-way Binding Posts BR Version - Barrier Strip inputs with Multi-way Binding Posts SP Version - XLR and 1/4" TRS inputs with Neutrik™ Speakons™ • Independent level controls for CH1 & CH2 • Independent CH1and CH2 switchable High Pass Filters, selectable at 30Hz or 80Hz • Independent CH1and CH2 select
PXm450 • 450W bridged mono into 8 ohms 275W per channel into 2 ohms 225W per channel into 4 ohms 150W per channel into 8 ohms • Three connector versions available: Standard - XLR and 1/4" TRS inputs with Multi-way Binding Posts BR Version - Barrier Strip inputs with Multi-way Binding Posts SP Version - XLR and 1/4" TRS inputs with Neutrik™ Speakons™ • Independent level controls for CH1 & CH2 • Independent CH1and CH2 switchable High Pass Filters, selectable at 30Hz or 80Hz • Independent CH1and CH2 select
PXm900 • 900W bridged mono into 8 ohms 550W per channel into 2 ohms 450W per channel into 4 ohms 300W per channel into 8 ohms connector versions available: • Three Standard XLR and 1/4" TRS inputs with Multi-way Binding Posts BR Version - Barrier Strip inputs with Multi-way Binding Posts SP Version - XLR and 1/4" TRS inputs with Neutrik™ Speakons™ • Independent Level controls for CH1 & CH2 • Independent CH1 and CH2 switchable High Pass Filters, selectable at 30Hz or 80Hz • Independent CH1 and CH2 selecta
PXm900 • 900W bridged mono into 8 ohms 550W per channel into 2 ohms 450W per channel into 4 ohms 300W per channel into 8 ohms connector versions available: • Three Standard XLR and 1/4" TRS inputs with Multi-way Binding Posts BR Version - Barrier Strip inputs with Multi-way Binding Posts SP Version - XLR and 1/4" TRS inputs with Neutrik™ Speakons™ • Independent Level controls for CH1 & CH2 • Independent CH1 and CH2 switchable High Pass Filters, selectable at 30Hz or 80Hz • Independent CH1 and CH2 selecta
Installation Location and General Precautions Observe the following precautions when choosing a location for your amplifier. A. Do not expose the unit to rain or moisture. If a fluid or foreign object should enter the unit, disconnect the power plug and contact an authorized dealer or service center. Do not pull the plug by pulling on the cord; grasp the plug firmly. B. Protect from heat and allow adequate ventilation. Place away from direct sources of heat, such as heating vents and radiators.
Installation Location and General Precautions Observe the following precautions when choosing a location for your amplifier. A. Do not expose the unit to rain or moisture. If a fluid or foreign object should enter the unit, disconnect the power plug and contact an authorized dealer or service center. Do not pull the plug by pulling on the cord; grasp the plug firmly. B. Protect from heat and allow adequate ventilation. Place away from direct sources of heat, such as heating vents and radiators.
High Pass Filter Cut Off Frequency The High Pass Filter Cut Off frequency is independently selectable for each channel at a frequency of either 30Hz or 80Hz. In the 30Hz position this filter performs much like a subsonic filter, eliminating power-robbing low frequencies below the audible or useable range. In the 80Hz position the High Pass Filter protects sensitive high frequency drivers from low frequency transients that could damage voice coils or diaphragms.
High Pass Filter Cut Off Frequency The High Pass Filter Cut Off frequency is independently selectable for each channel at a frequency of either 30Hz or 80Hz. In the 30Hz position this filter performs much like a subsonic filter, eliminating power-robbing low frequencies below the audible or useable range. In the 80Hz position the High Pass Filter protects sensitive high frequency drivers from low frequency transients that could damage voice coils or diaphragms.
Operating Tips Using the PXm Amplifiers Once the amplifier has been installed and wired into the system, you are ready to use it. Here are some tips to help you get the most from your new PXm amplifier. • Verify that the switches (Output Configuration, Input Sensitivity, High Pass Filter and Clip Limiter) have been set to the mode or selection that you had intended for your application.
Operating Tips Using the PXm Amplifiers Once the amplifier has been installed and wired into the system, you are ready to use it. Here are some tips to help you get the most from your new PXm amplifier. • Verify that the switches (Output Configuration, Input Sensitivity, High Pass Filter and Clip Limiter) have been set to the mode or selection that you had intended for your application.
Warranty Information Professional Power Amplifiers: 5 years NOTE: The following warranty is exclusive to the United States and its possessions and territories. Please see your Carver Professional dealer or distributor for the correct warranty information in your area or locale. WHAT IS COVERED: THIS WARRANTYCOVERS DEFECTS IN MATERIALAND WORKMANSHIPONLY.
Warranty Information Professional Power Amplifiers: 5 years NOTE: The following warranty is exclusive to the United States and its possessions and territories. Please see your Carver Professional dealer or distributor for the correct warranty information in your area or locale. WHAT IS COVERED: THIS WARRANTYCOVERS DEFECTS IN MATERIALAND WORKMANSHIPONLY.
† † pxm250/450/900 Professional Stereo Power Amplifier Made In America 8100.0157A †Available in North America only A Division Of Phoenix Gold International, Inc. 9300 North Decatur ● Portland OR 97203 ● Tel: 503.288.2008 ● Fax: 503.978.3302 ● Email: carverpro@imagina.