Owner's Manual

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SAFETY INSTRUCTIONS (EUROPEAN)
The conductors in the AC power cord are colored in accordance with the following code.
GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live
U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is
unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAM-
AGED OR CUT MAIN PLUG INTO A POWER SOCKET.
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken
so that objects do not fall and liquids are not spilled into the enclosure through openings.
POWER SOURCES: The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polar-
ization means of an appliance is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the appliance.
SERVICING: The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse.
Refer to replacement text on the unit for correct fuse type.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL! THIS UNIT CONTAINS HIGH
VOLTAGE INSIDE!
CAUTION
RISK OF ELECTRIC SHOCK
D6 03-50135 1 EACH STANDOFF LED .500 X .135 T1
D7 03-50135 1 EACH STANDOFF LED .500 X .135 T1
S1 06-40040 4 EACH TERMINAL VERT FEML PC MTG .250
QC5 06-40050 1 EACH TERMINAL VERT MALE PC MTG .250
QC1 06-40060 2 EACH TERMINAL 90dg MALE PC MTG .250
QC2 06-40060 2 EACH TERMINAL 90dg MALE PC MTG .250
J11 21-40000 6 EACH XLR FEML CON NEUTRIK #NC3FAV-0
J21 21-40000 6 EACH XLR FEML CON NEUTRIK #NC3FAV-0
J31 21-40000 6 EACH XLR FEML CON NEUTRIK #NC3FAV-0
J41 21-40000 6 EACH XLR FEML CON NEUTRIK #NC3FAV-0
J51 21-40000 6 EACH XLR FEML CON NEUTRIK #NC3FAV-0
J61 21-40000 6 EACH XLR FEML CON NEUTRIK #NC3FAV-0
J5 21-40022 1 EACH JACK RCA QUAD PC VERTICAL MTG
J1 21-50345 “11 EACH JACK .250”” PHONE MONO PCB MTG”
J2 21-50345 “11 EACH JACK .250”” PHONE MONO PCB MTG”
J3 21-50345 “11 EACH JACK .250”” PHONE MONO PCB MTG”
J4 21-50345 “11 EACH JACK .250”” PHONE MONO PCB MTG”
J6 21-50345 “11 EACH JACK .250”” PHONE MONO PCB MTG”
J12 21-50345 “11 EACH JACK .250”” PHONE MONO PCB MTG”
J22 21-50345 “11 EACH JACK .250”” PHONE MONO PCB MTG”
J32 21-50345 “11 EACH JACK .250”” PHONE MONO PCB MTG”
J42 21-50345 “11 EACH JACK .250”” PHONE MONO PCB MTG”
J52 21-50345 “11 EACH JACK .250”” PHONE MONO PCB MTG”
J62 21-50345 “11 EACH JACK .250”” PHONE MONO PCB MTG”
F1 23-03529 2 EACH FUSEHOLDER CLIPS 3AG VERT MTG
“H2, H4, H5, H6, H7, H8”
23-11004 6 EACH CONNECT HEADER 4 PIN STRAIGHT
“H1, H10, H11, H12”
23-11008 4 EACH CONNECT HEADER 8 PIN STRAIGHT
“H13, H14” 23-11010
2 EACH CONNECT HEADER 10 PIN STRAIGHT
H9 23-15605 “1 EACH CONNECT HEADER .156”” 5 PIN”
H3 23-40008 1 EACH CONNECT HEADER .400 IN 8 PIN
H3 middle pins 23-92995
2 EACH SHUNT JUMPER UNPLATED
“S4, S11, S21, S31, S41, S51, S61”
25-02201- 1 * STD 7 EACH ASSEMBLED
SWITCH AND CAP
AA 30-62004 1 EACH PCB CARD SYS MSTR PA620/410
“C58, C98” 42-47251-
“1 * STD 2 EACH CAP ELEC 4,700 MFD 50V 20%”
C150 or C250 46-22461
1 EACH CAP MYLR .2200UF 63VOLT 10%
“C14, C15, C61, C70, C84, C85, C94”
47-10225 “7 EACH CAP ELEC 1,000 MFD 25V 20%”
“C49, C51, C53, C71, C111, C117, C123, C211, C223, C311, C323,
C411, C423, C511, C523, C611, C623”
49-10212 17 EACH 0.001UF SMT 10% FILM 0805 50V
“C27, C40, C43, C57, C95”
49-10312 5 EACH 0.01UF SMT 10% FILM 080550V
“C3, C4, C7, C10, C11, C12,”
49-10412 23 EACH 0.1UF SMT 5% CERAMIC 0805
“C13, C24, C35, C39, C60, C65,”
49-10412 23 EACH 0.1UF SMT 5% CERAMIC 0805
“C74, C75, C76, C77, C78, C79,”
49-10412 23 EACH 0.1UF SMT 5% CERAMIC 0805
“C80, C142, C151, C152, C155”
49-10412 23 EACH 0.1UF SMT 5% CERAMIC 0805
“C42, C44, C99” 49-10451
3 EACH 0.1 uF SMT 10% FILM 1206 50V
“C2, C5, C16, C19, C20, C21,”
49-22035 58 EACH SMT CAP 22uF 35v ELECTROLITIC
“C22, C26, C29, C31, C34, C56,”
49-22035 58 EACH SMT CAP 22uF 35v ELECTROLITIC
“C59, C62, C63, C64, C66, C67,”
49-22035 58 EACH SMT CAP 22uF 35v ELECTROLITIC
“C68, C93, C103, C104, C105, C108,”
49-22035 58 EACH SMT CAP 22uF 35v ELECTROLITIC
“C110, C114, C153, C154,”
49-22035 58 EACH SMT CAP 22uF 35v ELECTROLITIC
“C203, C204, C205, C208, C210, C214,”
49-22035 58 EACH SMT CAP 22uF 35v ELECTROLITIC
“C303, C304, C305, C308, C310, C314,”
49-22035 58 EACH SMT CAP 22uF 35v ELECTROLITIC
“C403, C404, C405, C408, C410, C414,”
49-22035 58 EACH SMT CAP 22uF 35v ELECTROLITIC
“C503, C504, C505, C508, C510, C514,”
49-22035 58 EACH SMT CAP 22uF 35v ELECTROLITIC
“C603, C604, C605, C608, C610, C614,”
49-22035 58 EACH SMT CAP 22uF 35v ELECTROLITIC
“C72, C122, C124, C135”
49-22212 4 EACH 0.0022UF SMT 10% FILM 0805 50V
“C50, C112, C134, C212, C312, C412, C512, C612”
49-22312 8 EACH 0.022UF SMT 10% FILM 0805 50V
“C8, C9” 49-25152
2 EACH 220PF SMT 5% CERAMIC 0805
“C8, C9”
“C1, C36, C37, C106, C107,”
49-27052 16 EACH 27 PF SMT 5% CERAMIC 0805
“C206, C207, C209, C306, C307,”
49-27052 16 EACH 27 PF SMT 5% CERAMIC 0805
“C406, C407, C506, C507, C606, C607”
49-27052 16 EACH 27 PF SMT 5% CERAMIC 0805
C55 49-33152 1 EACH 330PF SMT 5% CERAMIC 0805
C47 49-33212 1 EACH 0.0033UF SMT 10% FILM 0805 50
“C38, C48” 49-33312
2 EACH 0.033UF SMT 10% FILM 0805 50V
“C17, C18, C23, C25, C28, C33,”
49-39052 24 EACH 39PF SMT 5% CERAMIC 0805
“C69, C82, C87, C90, C100, C109,”
49-39052 24 EACH 39PF SMT 5% CERAMIC 0805
“C113, C118, C119, C213, C309, C313,”
49-39052 24 EACH 39PF SMT 5% CERAMIC 0805
“C409, C413, C509, C513, C609, C613”
49-39052 24 EACH 39PF SMT 5% CERAMIC 0805
“C45, C52, C54” 49-47212
3 EACH 0.0047uF SMT FILM 0805 50V
“C32, C46, C73” 49-47312
2 EACH 0.047UF SMT 10% FILM 0805 50V
“C30, C41, C101, C102, C201, C202, C301,”
49-82052 14 EACH 82PF SMT 5% CERAMIC 0805
“C302, C401, C402, C501, C502, C601, C602”
49-82052 14 EACH 82PF SMT 5% CERAMIC 0805
“R222, R224” 58-92201
2 EACH 22 SMT 1W 2512 20%
“R59, R60, R89, R128”
55-03300 4 EACH RES .33 OHM 5W 5% SB VERT
R196 58-00035 1 EACH 0.0 SMT JUMPER 1206
“R85, R91, R165, R171, R172, R188, R189”
58-10015 7 EACH 10.5 SMT .25W 1206 1%
R40 58-10025 1 EACH 100.5 SMT .25W 1206 1%
“R48, R66, R78, R81, R86, R99,”
58-10035 15 EACH 1K SMT .25W 1206 1%
“R111, R131, R133, R136, R150, R158,”
58-10035 15 EACH 1K SMT .25W 1206 1%
“R187, R190, R191”
58-10035 15 EACH 1K SMT .25W 1206 1%
“R1, R4, R28, R29, R30,”
58-10045 39 EACH 10K SMT .25W 1206 1%
“R31, R35, R36, R37, R39,”
58-10045 39 EACH 10K SMT .25W 1206 1%
“R83, R116,” 58-10045
39 EACH 10K SMT .25W 1206 1%
“R120, R121, R123, R139,”
58-10045 39 EACH 10K SMT .25W 1206 1%
“R152, R153, R154, R156, R159, R160,”
58-10045 39 EACH 10K SMT .25W 1206 1%
“R167, R170, R175, R176, R193,”
58-10045 39 EACH 10K SMT .25W 1206 1%
“R198, R199, R216, R223, R316,”
58-10045 39 EACH 10K SMT .25W 1206 1%
“R323, R416, R423,”
58-10045 39 EACH 10K SMT .25W 1206 1%
“R516, R523, R616, R623”
58-10045 39 EACH 10K SMT .25W 1206 1%
“R52, R61, R71, R100, R134, R135, R138”
58-10055 7 EACH 100K SMT .25W 1206 1%
“R92, R94, R144” 58-10065
3 EACH 1M SMT .25W 1206 1%
“R112, R115, R212, R215, R312, R315,”
58-15035 12 EACH 1.5K SMT .25W 1206 1%
“R412, R415, R512, R515, R612, R615”
58-15035 12 EACH 1.5K SMT .25W 1206 1%
“R38, R105, R125, R205,”
58-15045 8 EACH 15K SMT .25W 1206 1%
“R305, R405, R505, R605”
58-15045 8 EACH 15K SMT .25W 1206 1%
“R2, R8, R41, R44,”
58-15055 8 EACH 150K SMT .25W 1206 1%
“R54, R65, R67, R79”
58-15055 8 EACH 150K SMT .25W 1206 1%
“R76, R130, R137”58-22025
3 EACH 220.5 SMT .25W 1206 1%
“R21, R27, R32, R47, R53, R55, R56,”
58-22035 36 EACH 2.2K SMT .25W 1206 1%
“R62, R64, R68, R72, R74, R95, R97,”
58-22035 36 EACH 2.2K SMT .25W 1206 1%
“R103, R104, R124, R142, R155, R157,”
58-22035 36 EACH 2.2K SMT .25W 1206 1%
“R169, R203, R204, R303, R304,”
58-22035 36 EACH 2.2K SMT .25W 1206 1%
“R403, R404, R503, R504, R603, R604,”
58-22035 36 EACH 2.2K SMT .25W 1206 1%
“R117, R217, R317, R417, R517, R617”
58-22035 36 EACH 2.2K SMT .25W 1206 1%
“R5, R10, R11, R12, R14,”
58-22045 41 EACH 22K SMT .25W 1206 1%
“R15, R16, R18, R19, R23,”
58-22045 41 EACH 22K SMT .25W 1206 1%
“R24, R25, R26, R33,”
58-22045 41 EACH 22K SMT .25W 1206 1%
“R108, R109, R113, R126, R127, R129,”
58-22045 41 EACH 22K SMT .25W 1206 1%
“R132, R137, R140, R141, R148, R149, R163,”
58-22045 41 EACH 22K SMT .25W 1206 1%
“R208, R209, R213, R308, R309, R313,”
58-22045 41 EACH 22K SMT .25W 1206 1%
“R408, R409, R413, R508, R509, R513,”
58-22045 41 EACH 22K SMT .25W 1206 1%
“R608, R609, R613”
58-22045 41 EACH 22K SMT .25W 1206 1%
“R20, R22, R63, R69, R73, R75”
58-22055 6 EACH 220K SMT .25W 1206 1%
“R50, R90” 58-27025
2 EACH 270.5 SMT .25W 1206 1%
“R77, R82, R161, R162, R177, R178, R233”
58-33025 7 EACH 330.5 SMT .25W 1206 1%
“R70, R106, R107, R168, R206,”
58-33035 14 EACH 3.3K SMT .25W 1206 1%
“R207, R306, R307, R406, R407,”
58-33035 14 EACH 3.3K SMT .25W 1206 1%
“R506, R507, R606, R607”
58-33035 14 EACH 3.3K SMT .25W 1206 1%
“R3, R9, R34, R145”
58-33045 * STD 4 EACH 33K SMT .25W 1206 1%
“R48, R58, R88, R200”
58-47015 4 EACH 47.5 SMT .25W 1206 1%
“R42, R43, R45, R80, R93, R98, R146”
58-47025 7 EACH 470.5 SMT .25W 1206 1%
“R6, R13, R17, R84,”
58-47035 22 EACH 4.7K SMT .25W 1206 1%
“R110, R118, R119, R210, R218, R219,”
58-47035 22 EACH 4.7K SMT .25W 1206 1%
“R310, R318, R319, R410, R418, R419,”
58-47035 22 EACH 4.7K SMT .25W 1206 1%
“R510, R518, R519, R610, R618, R619”
58-47035 22 EACH 4.7K SMT .25W 1206 1%
“R46, R57, R87, R96, R114,”
58-47045 13 EACH 47K SMT .25W 1206 1%
“R147, R164, R166, R214”
58-47045 13 EACH 47K SMT .25W 1206 1%
“R314, R414, R514, R614”
58-47045 13 EACH 47K SMT .25W 1206 1%
R92 58-47055 1 EACH 470K SMT .25W 1206 1%
R7 58-56025 1 EACH 560.5 SMT .25W 1206 1%
“R101, R102, R201, R202, R301, R302,”
58-56035 12 EACH 5.6K SMT .25W 1206 1%
“R401, R402, R501, R502, R601, R602”
58-56035 12 EACH 5.6K SMT .25W 1206 1%
“R173, R174, R192, R193, R194, R195”
58-68015 6 EACH 68.5 SMT .25W 1206 1%
“R49, R51, R151” 58-68025
3 EACH 680 SMT .25W 1206 1%
R122 58-68035 1 EACH 6.8K SMT .25W 1206 1%
“R142, R143” 58-91025
2 EACH 910.5 SMT .25W 1206 1%
“Q32, Q34” 60-00142
2 EACH TRANS NPN TIP142 TO-218
“Q31, Q33” 60-00147
2 EACH TRANS PNP TIP147 TO-218
“D31, D32, D33, D34”
60-50200 4 EACH DIODE GEN REC 1N5402 3A 200V
“Q2, Q11, Q23, Q25”
60-55500- 1 * STD 4 EACH TRANS 2N5550
HV NPN 250V T0-92
U3 60-71024 1 EACH CMOS STATIC RAM 1MEG 20NS
D6 60-75320 1 EACH LED RED DIFFUSED 3MM T-1.00
D1 60-75330 1 EACH LED GREEN DIFFUSED 3MM T-1.00
D2 60-75340 1 EACH LED YELLOW DIFFUSED 3MM T-1.00
Q27 60-78050 1 EACH REGULATOR VOLTAGE 5 +V 1 AMP
Q14 62-04391 1 EACH TRANSISTOR SMT MMBF4391LT1
“Z1, Z2, Z3, Z4, Z11, Z12, Z13”
62-04739 7 EACH SMT DIODE ZENER 4739
“D15, D16, D17, D18, D35, D36”
62-06001 6 EACH DIODE ULTRA FAST 600V 1A SMA
U1 62-07712 1 EACH IC DSP W/CODEC AKM7712
Y1 62-16400 1 EACH CRYSTAL CERAMIC SMT 16.4mHz
“D3, D4, D5, D7, D8, D9,”
62-19140 11 EACH 1N914 HI SPD SMT 250mW DIODE
“D10, D11, D12, D13, D14”
62-19140 11 EACH 1N914 HI SPD SMT 250mW DIODE
“A10, A11, A21, A31, A41, A51, A61”
62-20430 7 EACH NJM2043SMT(TESTED) DUAL HFREQ
“A1, A2, A3, A4, A5, A7,”
62-45650 16 EACH NJM4565 SMT DUAL HI FREQ
“A8, A9, A12, A15, A16,”
62-45650 16 EACH NJM4565 SMT DUAL HI FREQ
“A22, A32, A42, A52, A62”
62-45650 16 EACH NJM4565 SMT DUAL HI FREQ
“Q3, Q4, Q5, Q6, Q9, Q10, Q13, Q16, Q17, Q18, Q21, Q24”
62-54001 12 EACH MMBT5401LTI PNP SOT-23 SMT
“Q7, Q8, Q19, Q20”
62-55500 4 EACH MMBT5550 NPN SOT-23
U2 62-87764 1 EACH MICRO CONTROLLER SOIC PACKAGE
“K1, K2” 70-05713
2 EACH RELAY SPDT 12A@120VAC/24V COIL
F1 70-21050 1 EACH FUSE ABC 5.00A FAST 6.35X32MM
“P11, P13, P21, P23, P31, P33,”
71-09252 “12 EACH POT 9 “”D-P”” 25F B50K-CC”
“P41, P43, P51, P53, P61, P63”
71-09252 “12 EACH POT 9 “”D-P”” 25F B50K-CC”
“P1, P2, P3, P8, P9, P10,”
71-09253 “24 EACH POT 9 “”D-P”” 25F B50K-”
“P14, P16, P17, P24, P26, P27,”
71-09253 “24 EACH POT 9 “”D-P”” 25F B50K-”
“P34, P36, P37, P44, P46, P47,”
71-09253 “24 EACH POT 9 “”D-P”” 25F B50K-”
“P54, P56, P57, P64, P66, P67”
71-09253 “24 EACH POT 9 “”D-P”” 25F B50K-”
“P72, P73, P74, P75, P76, P77, P78”
71-10320 7 EACH FADER 20MM SL20V3-B10K-L15D(G)
REPLACEMENT PARTS LIST (for circuit cards)
This symbol is intended to
alert the user to the pres-
ence of uninsulated “dan-
gerous voltage” within the
product’s enclosure that may be of suf-
ficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intend-
ed to alert the user to
the presence of impor-
tant operating and
maintenance (servicing) instructions
in the literature accompanying the
appliance.
LIMITED WARRANTY
Your Carvin product is guaranteed against failure for 1 YEAR unless otherwise stated.
Carvin will service and supply all parts at no charge to the customer providing the unit is
under warranty. Shipping costs are the responsibility of the customer. CARVIN DOES NOT
PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF THE ORIGINAL
INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin assumes no responsibility
for horn drivers or speakers damaged by this unit. This warranty does not cover, and no
liability is assumed, for damage due to: natural disasters, accidents, abuse, loss of parts,
lack of reasonable care, incorrect use, or failure to follow instructions. This warranty is in
lieu of all other warranties, expressed or implied. No representative or person is authorized
to represent or assume for Carvin any liability in connection with the sale or servicing of
Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
When RETURNING merchandise to the factory, you may call for a return authorization
number. Describe in writing each problem. If your unit is out of warranty, you will be
charged the current FLAT RATE for parts and labor to bring your unit up to factory spec-
ifications.
MAINTAINING YOUR EQUIPMENT
Avoid spilling liquids or allowing any other foreign matter inside the unit. The panel of
your unit can be wiped from time to time with a dry or slightly damp cloth in order to
remove dust and bring back the new look. As with all pro gear, avoid prolonged use in
caustic environments (salt air). When used in such an environment, be sure the mixer
is adequately protected by a cover.