Owner's Manual

ManualsBrandsCarvin ManualsAudioCarvin XP800L

CONGRATULATIONS on your purchase of Carvin’s XP800L mixer! The XP800L

model includes 2 built-in high power amplifiers for direct hook-up to your speakers.

Please read this manual carefully to take all the advantages of your new mixer.

SUPERB SOUND is derived from the extremely low distortion, “high headroom”

design. State-of-the art, low noise, balanced XLR preamps from our Concert Series

mixers provide common mode rejection of better than 78 dB, which means that any

noise that may come over your cables is virtually eliminated. Distortion is nearly

non-existent with THD below 0.1% from input to output, guaranteeing the purity of

your sound. Hear the difference - your sound will not seem sterile or processed. It

will be dynamically open and transparent just like it was meant to be!

LIGHT WEIGHT / EASY TO USE Controls are logically laid out making the XP

Series simple to use, reducing errors during setup and performance. Its compact

size and weight of only 10 lbs. makes it the lightest, most powerful mixer in it’s class.

2 HIGH CURRENT “GREEN” CLASS-D AMPLIFIERS produce total of 500 watts

RMS, 750 watts peak. Class-D amps not only run cooler, but are also energy effi-

cient. Use both amps in stereo (250w/250w) for MAIN L and R speakers, or switch

to 250watts for MAIN and 250watts for MONITORS. This is the kind of output power

that maintains the purity and integrity of your sound.

HIGH CURRENT “GREEN” SWITCHMODE POWER SUPPLY conserves power

by operating at higher efficiency. The DC voltage supply is recharged 100,000 times

per second, delivering continuous high current to the power amps.

24-Bit DSP STEREO EFFECT PROCESSOR delivers professional level effects.

You get awesome lush Reverbs, rich Chorus, crisp Delay and Echo, and thick, layered

Flanging – all with full bandwidth and pristine clarity. Effect level is adjustable to your

stage monitors so you can hear yourself with full effects. 256 effect variations

include fully adjustable parameters for damping, decay, depth, speed, regeneration

and time.

ACTIVE 3 BAND CHANNEL EQ provides easy adjustment for the tone you want.

The 80Hz LO frequency controls deliver solid non-flabby bass. A simple adjustment

with the MID band control brings out the best sound for vocals or guitar by affecting

the very important 750Hz frequency range. The 11.5k Hz HI treble control adds

sparkle to your top-end without adding harshness. Both the LO and HI controls are

"shelving", which means they are effective from 20Hz to 20kHz.

DUAL 7-BAND EQUALIZER provides precise adjustments to fine tune your overall

sound and to help control feedback. The stereo (dual) graphic equalizer controls

the main L and R outputs or switch to MAIN/MONITOR with one press of a button.

ENGINEERED TO LAST Every XP Series mixer incorporates a rugged steel chas-

sis with protective side panels. Continuous full power is assured from a high-grade

6063-T5-aluminum heat sink. Sealed controls and switches guard against the out-

side elements while heavy-duty connectors provide a positive connection to your

cables. Hidden deep in the heart of these mixers is the “SMT” Surface Mount

Technology construction that utilizes surface mounted components to prevent parts

from shaking or vibrating loose. Precision 1% tolerances guarantee that your set-

tings will be accurate every time. Fire retardant FR-4 military spec circuit cards fea-

ture double-sided copper construction to guard against noise and radio frequencies

(RF). The XP Series is made in the USA for years of dependable service!

LEFT

RIGHT

MONITOR

EFFECTS

CHANNELS 1-4

+20dB

GAIN SW

CHANNELS 5/6, 7/8

MAIN/MON

SWITCH

AMP 1

AMP 2

MONITOR

LEVEL

MAIN

LEVEL

EFF

MON

OUT

LEFT

OUT

RIGHT

OUT

EFF

SEND

EFFECTS

TO MAIN

EFFECTS

TO MONITOR

TAPE OUT

MONITOR

STEREO

THREE BAND

TONE

CONTROLS

THREE BAND

TONE

CONTROLS

STEREO

GRAPHIC

EQUALIZER

LINE

MIC

RETURN FROM

INTERNAL DSP

INTERNAL

DSP INPUT

HI MID LOW

PAD

MIC

PRE

MIC

PRE

EFF

12340 World Trade Drive, San Diego, CA 92128

800.854.2235 www.carvin.com

76-80000A 909b

MODEL XP800L SPECIFICATIONS:

Frequency Response: Mic or Line Inputs: 20Hz-20kHz ±1dB

Total Harmonic Distortion: Less than .1% at nominal levels

Equivalent Input Noise: 150 ohm source: -117dBu

Output Noise: -90dBu Master Line Out

(All Levels Minimum)

Output Headroom: +20dB

Maximum Gain: Mic in to Master Line Out: 70dB

Crosstalk: Adjacent ch’s: -60db at 1KHz

Common Mode Rejection: -78db at 1KHz

Phantom Power: 48volt @ XLR Mic channels

USB Power port: 5volt, 250mA for LED lighting or MP3 charging

Channel EQ 3-band active:

LOW: 80Hz ±12dB

MID: 750Hz ±12dB

HI: 11.5KHz ±12dB

Power Output: 500wRMS (2x250w@4ohms), 750w peak total

Power Req.: 100-140VAC or 200-250VAC, 50-60Hz

Size and Weight: 7.5”H x 13.5”W x 9”D, 10 lbs

Vinyl Cover: CV800

XP800L BLOCK DIAGRAM

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SAFETY INSTRUCTIONS (EUROPEAN)

The conductors in the AC power cord are colored in accordance with the following code.

GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live

U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is

unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAM-

AGED OR CUT MAIN PLUG INTO A POWER SOCKET.

IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:

WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,

kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken

so that objects do not fall and liquids are not spilled into the enclosure through openings.

POWER SOURCES: The appliance should be connected to a power supply only of the type

described in the operating instructions or as marked on the appliance.

GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polar-

ization means of an appliance is not defeated.

POWER CORD PROTECTION: Power supply cords should be routed so that they are not like-

ly to be walked on or pinched by items placed upon or against them, paying particular attention

to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

SERVICING: The user should not attempt to service the appliance beyond that described in the

operating instructions. All other servicing should be referred to qualified service personnel.

FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse.

Refer to replacement text on the unit for correct fuse type.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL! THIS UNIT CONTAINS HIGH

VOLTAGE INSIDE!

CAUTION

RISK OF ELECTRIC SHOCK

This symbol is intended to

alert the user to the pres-

ence of uninsulated “dan-

gerous voltage” within the

product’s enclosure that may be of suf-

ficient magnitude to constitute a risk of

electric shock to

persons.

This symbol is intend-

ed to alert the user to

the presence of impor-

tant operating and

maintenance (servicing) instructions

in the literature accompanying the

appliance.

LIMITED WARRANTY

Your Carvin product is guaranteed against failure for 1 YEAR unless otherwise stated.

Carvin will service and supply all parts at no charge to the customer providing the unit is

under warranty. Shipping costs are the responsibility of the customer. CARVIN DOES

NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF THE

ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin assumes

no responsibility for horn drivers or speakers damaged by this unit. This warranty does

not cover, and no liability is assumed, for damage due to: natural disasters, accidents,

abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow instructions.

This warranty is in lieu of all other warranties, expressed or implied. No representative or

person is authorized to represent or assume for Carvin any liability in connection with the

sale or servicing of Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES.

When RETURNING merchandise to the factory, you may call for a return authoriza-

tion number. Describe in writing each problem. If your unit is out of warranty, you will

be charged the current FLAT RATE for parts and labor to bring your unit up to factory

specifications.

MAINTAINING YOUR EQUIPMENT

Avoid spilling liquids or allowing any other foreign matter inside the unit. The panel of

your unit can be wiped from time to time with a dry or slightly damp cloth in order to

remove dust and bring back the new look. As with all pro gear, avoid prolonged use in

caustic environments (salt air). When used in such an environment, be sure the mixer

is adequately protected by a cover.

CARVIN ENGINEERING DATA

XP800L POWERED MIXER OPERATING MANUAL

RECEIVING INSPECTION—read before getting started

INSPECT YOUR MIXER FOR DAMAGE which may have occurred during

shipping. If damage is found, please notify the shipping company and

CARVIN immediately.

SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have

to re-ship your unit, always use the original carton and packing material. This

will provide the best possible protection during shipment. CARVIN and the

shipping company are not liable for any damage caused by improper packing.

SAVE YOUR INVOICE. It will be required for warranty service if needed in

the future.

SHIPMENT SHORTAGE. If you find items missing, they may have been

shipped separately. Please allow several days for the rest of your order to

arrive before inquiring.

RECORD THE SERIAL NUMBER on the enclosed warranty card or below

on this manual for your records. Keep your portion of the card and return the

portion with your name and comments to us.

USA customers register online at: www

.carvin.com/registration

All other countries register online at: www

.carvinworld.com/registration

For your records, you may wish to record the following information.

Serial No._____________________ Invoice Date_______________

XP800L LIVE SET UP

MADE IN THE USA

A NOTE ABOUT SPEAKER IMPEDANCE (OHMS) and CABLES

As you add more speakers to an amp, the total impedance (ohms) is

reduced. The amplifiers will drive an impedance of 4ohms or higher. This

means up to TWO 8ohm speakers, or ONE 4ohm speaker for each amp.

Speaker cables should be a minimum 16 gauge for up to 50ft (C50S).

8 ohms

MAIN (or LEFT) SPEAKERS

MONITOR (or RIGHT) SPEAKERS

8 ohms

Summary of content (2 pages)

PAGE 1
CARVIN ENGINEERING DATA XP800L POWERED MIXER OPERATING MANUAL XP800L LIVE SET UP RECEIVING INSPECTION—read before getting started INSPECT YOUR MIXER FOR DAMAGE which may have occurred during shipping. If damage is found, please notify the shipping company and CARVIN immediately. SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your unit, always use the original carton and packing material. This will provide the best possible protection during shipment.
PAGE 2
XP800L CONTROLS QUICK START UP If you’re like most new owners, you’re probably in a hurry to plug your mixer in and use it. Here are some brief instructions to get you going quickly. With the mixer unplugged and the unit turned off, complete the following procedures: A. CONNECTING AC POWER TO YOUR MIXER • Be sure to plug your mixer into the proper AC voltage marked on the rear of your mixer. • Use only a grounded (3 prong) power outlet to prevent a shock hazard (do not bypass).