CAMPANA ™ OWNER’S MANUAL 3-Speed Model Only
CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PREPARATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FAN INSTALLATION . . . . . . . . . . . . . . . . . . . . . .
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7′ above the floor.
CAMPANA™ PREPARATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed.
CROSSBAR MOUNTING BRACKET INSTALLATION CEILING FAN Proceed with installation as follows: Step 1. Route the wires from the ceiling outlet box through APPROVED the crossbar mounting bracket center hole. Attach the bracket, OUTLET BOX with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet box. Tighten the screws firmly by hand only, being careful not to CEILING bend the bracket by over tightening.
CAMPANA™ HANGING THE FAN Step 3. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Check that no wires were pinched. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. 3-Speed Note: Independent control of the light fixture using a W-80 requires an additional independent power wire run from the wall switch to the fan. See Page 10 for wiring.
CANOPY HATCH INSTALLATION Step 5. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Step 6. Install canopy hatch with the last canopy screw and lock washer. To do this, tilt the fan body away from the hatch opening. Tighten the screws firmly by hand only, Step 7.
CAMPANA™ BLADE TO BLADE HOLDER INSTALLATION Step 9. Attach each blade to a blade holder securing it with the four steel washers and blade screws provided. Tighten securely by hand only. BLADE SCREW (4 PER BLADE) WASHER (4 PER BLADE) BLADE BLADE HOLDER INSTALL BLADE ASSEMBLY TO FAN ROTATE FLYWHEEL TO INSTALL BLADE HOLDER SCREWS Step 10. Attach each blade/blade holder assembly to the motor. Tighten securely by hand only.
3-SPEED ONLY: ATTACHING SWITCH HOUSING WIRES Step 11. For 3-Speed models only: Hold the switch housing up to the fan and connect the motor plug to the switch housing socket. The connector is keyed to ensure correct installation. WARNING: Do not force the connectors– check that they are orientated so the keying will match! SWITCH HOUSING CONNECTOR (SOCKET) Note: You may need to arrange the electronics inside the switch housing to make room for the connector.
3-SPEED ♦ OPERATION Pull-chain switches on the fan control the fan and lights. Using the fan control pull-chain switch: Fan off at start. First pull: fan ON, low speed Second pull: medium speed Third pull: high speed Fourth pull: fan OFF Using the optional light pull-chain switch: Light off at start. First pull: light ON Second pull: light OFF Direction of blade rotation is controlled by the reverse slide switch on the side of the switch housing. No changes in household wiring are required.
OPTIONAL 3-SPEED W-40 WALL CONTROL • The W-40 allows the choice of four (4) different speed settings. • No light fixture is used. • Set the FAN pull chain switch to the HIGH speed setting. • No changes in household or fan wiring are required. • The fan may be turned ON and OFF by the W-40 wall control. CAUTION! Failure to set the pull-chain speed to HIGH can result in faulty operation of the fan and damage to the W-40 wall control.
TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents.
2 SAFETY FIRST Warning: To reduce the risk of electrical shock this fan must be installed with an isolating wall control switch. VERSA•TOUCH 2 ♦ INSTALLATION W-72 CONTROL HOLDER W-72 CONTROL 12V BATTERY DRYWALL ANCHOR 6-32 (2) WOOD SCREW 1” (2) SCREW 6-32 X 3/8” (2) SCREW 6-32 X 1” (2) VERSA•TOUCH 2 ♦ CONTROL BRACKET INSTALLATION CAUTION! Do not use with wall dimmer.
2 VERSA•TOUCH 2 OPERATION SEND SIGNAL Fan Control LED To start the fan. Press the selected speed button to run the fan at the desired speed. LO=Low speed MED=Medium speed HI=High speed To turn off the fan. Press the FAN OFF button. MED Airflow Direction To reverse the airflow press the REVERSE button. Reverse operates at any speed whether fan is on or off. The fan returns to its set speed after reversing. LO Light Control Turn the light on or off independently from the fan by pressing the LIGHT button.
2 PROBLEM PROBLEM TROUBLESHOOTING VERSA•TOUCH 2 POSSIBLE POSSIBLE REMEDIES REMEDIES.. Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. FAN WILL NOT START •Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making sure the power is turned off during this inspection. •Pin connectors are not making good contact. Check the connections in the switch housing and under the top cover.
CAMPANA™ PERFORMANCE AND ENERGY INFORMATION Airflow (CFM)* Power Use (watts) Airflow Efficiency (CFM/watt) Low 1985 12 161 Med 3993 34 114 Hi 6689 81 82 Fan Speed 3 SPEED ONLY *Measured according to the ENERGY STAR®-approved Solid State test method. Ceiling fan airflow is measured in cubic feet per minute (CFM). Power use is measured in watts. To maximize energy savings, • Choose a fan with high airflow efficiency (CFM/watt). • Use ENERGY STAR®-labeled lighting in your fan.
761 CORPORATE CENTER DRIVE • POMONA, CA 91768 TOLL FREE: 888-CASA-1ST (227-2178) www.CasablancaFanCo.com ©COPYRIGHT 2003 CASABLANCA FAN COMPANY • U.S.